BBV4205402 - 07 Locking Spring Magnetic

Download as pdf or txt
Download as pdf or txt
You are on page 1of 1

1 2 3 4 5 6 7 8 9 10

DESIGN PRINCIPLE
OPERATING DATA VIEW-A SPRING SKETCH

2x
Torque (N.mm)
Spring function : -
06

3.
06 $
) 07
(253.9

2
C max
07
ngle
A

0. 1
A
free a
Service requirement :
C2
INSIDE DIA, 2x 2.3 0.1 10.9 0.2

2
L0
- Number of guaranteed operations : 10 000 B
in operating range : L1-L2
D02 L02
- Maximum temperature : < 100 °C

- Coil direction : Right and Left

C1 - Length of lever arm :


working range
C0 a = 3.7 mm b = 3.7 mm 06
Angle A (degree) - Material : Managed by Symphony
A0 A1 A2 An

A2
MATERIAL RECOMMENDATION
$
$5
b A1
d

2x 3.2 0.2
5

X01L01
A0 Use of CHLORINE products FORBIDDEN in the
44.
manufacturing process of the material and the component. 2x
In the case of thermal treatment > 300 $ C,
07
Da
it is OBLIGATORY to carry out a degreasing before this
07 07
thermal treatment 07
15 0.4
Angle Ao : Stress relieved
B
Free State
L03 (Including ends Burr) B

07 06
Dm

a
An
P

Angle A1 :
DATA TABLE Mini * Nominal * Maxi * Bending Radius - 0.8
Torque C1
under L1 = 0.45 mm, load P1 (N) 4 - -

Angle A2 : Max allowded burr on


Torque C2 under L2 = 2.2 mm, load P2 (N) - - 40 06 cutting edges are 0.1mm
06
Spring rate R (N.mm/deg)
C = R (A - Ao)
CZ
Maximal operating angle An (deg)

NOTE:
Assembly Angle (deg)
No deterior
C = P x a . with P(N) perpendicular 06
to the lever arm a (mm)
ation nor
Shaft diameter Da (mm)
tool marking
A
in these area
De maxi. (mm)

CALCULATED VALUES
C (Indicative values ) Di mini. (mm) 06
C

0.2
. . .

Wire diameter ------------------------ 0.7 mm Body length Lk under A2 (mm)


Mean coil diameter ------------------- 3.0 mm
5.9
Number of coils ---------------------- 2.36 TURNS BOTH SIDE
Spring rate R ------------------------ 1.56 N.mm/deg 07
Free angle Ao ----------------------- 253.9 deg
Stress under A2 --------------------- - %Rm
* - INDICATIVE VALUES
Maximal stress ----------------------- - %Rm
0.7 0.05 WIRE DIAMETER
Under angle ---------------------- - deg
D01
Tensile strength ---------------------- 2100 MPa
06
. . .

Use Fixture no. F21061154 to measure the indicative values

VIEW-A 07
SCALE 1.000

Scale: Tolerancing Standard : Units of measure :


5.000 ISO 8015 mm
D
LOCKING SPRING MAGNETIC
LOCKING SPRING MAGNETIC
Number: Revision: Sheet:
BBV4205402 07 1/1
State:
The information is highly confidential and is the exclusive property of Schneider Electric Group
copyright reserved. This drawing must not be used for any purpose other than that expressly permitted Released for Manufacturing
in writing by the owners and must not be disclosed or reproduced in any way without permission from the
owners in writing. This drawing must be returned to the owners when the purpose has ceased.
Printed on 2024/08/01

Original format A3

You might also like