E_S-1WR & F_S-1WR Series

1W, FIXED INPUT, ISOLATED & UNREGULATED

DUAL/SINGLE OUTPUT DC-DC CONVERTER

Patent Protection RoHS

FEATURES PRODUCT PROGRAM

Input Output
● SIP Package Part Efficiency
Voltage(VDC) Voltage Current (mA)
Number (%)(Typ.)
● Output Short Circuit Protection Nominal (VDC) Max Min
Range
● Little Isolation Capacitance
F0303S-1WR 3.3 303 30 68
● 3000VDC Isolation Voltage 3.3 3.0-3.6
● Operating Temperature: -40℃～+85℃ F0305S-1WR 5 200 20 70
● Internal SMD construction E0505S-1WR ±5 ±100 ±10 69
● Industry Standard Pinout E0509S-1WR ±9 ±56 ±5 73
● RoHS Compliance E0512S-1WR ±12 ±42 ±4 74
E0515S-1WR ±15 ±34 ±3 74
E0524S-1WR ±24 ±21 ±2 76
5 4.5-5.5
F0505S-1WR 5 200 20 73
APPLICATIONS F0509S-1WR 9 112 11 73
The E_S-1WR & F_S-1WR Series are F0512S-1WR 12 83 8 75
specially designed for applications where a F0515S-1WR 15 67 6 75
group of polar power supplies are isolated from F0524S-1WR 24 42 4 76
the input power supply in a distributed power E1205S-1WR ±5 ±100 ±10 70
supply system on a circuit board. E1212S-1WR ±12 ±42 ±4 76
These products apply to: E1215S-1WR ±15 ±34 ±3 76
1) Where the voltage of the input power
F1205S-1WR 12 10.8-13.2 5 200 20 73
supply is fixed (voltage variation ≤ ±10%);
F1209S-1WR 9 112 11 72
2) Where isolation is necessary between
F1212S-1WR 12 83 8 75
input and output (isolation voltage ≤3000VDC);
F1215S-1WR 15 67 6 76
3) Where the regulation of the output
E1505S-1WR ±5 ±100 ±10 70
voltage and the output ripple noise are not 15 13.5-16.5
demanding. F1515S-1WR 15 67 6 75
Such as: purely digital circuits, ordinary low E2405S-1WR ±5 ±100 ±10 70
frequency analog circuits, and IGBT power device E2412S-1WR ±12 ±42 ±4 76
driving circuits. E2415S-1WR ±15 ±34 ±3 76
F2403S-1WR 24 21.6-26.4 3.3 303 30 70
F2405S-1WR 5 200 20 70
MODEL SELECTION
F2412S-1WR 12 83 8 76
F2415S-1WR 15 67 6 76
F0505S-1WR Note:Models listed with strike-through text have been officially discontinued.

Rated Power COMMON SPECIFICATIONS

Package Style
Item Test conditions Min Typ Max Units
Output Volt age
.
Input Voltage Storage humidity 95 %
Product Series Operating Temperature -40 85
Storage Temperature -55 125
°C
Temp. rise at full load 20 30
MORNSUN Science & Technology Co.,Ltd.
Address: No. 5, Kehui St. 1, Kehui development
Lead temperature 1.5mm from case for 10 seconds 300
center, Science Ave., Guangzhou Science City, Cooling Free air convection
Luogang district, Guangzhou,P.R.China. Case material Plastic (UL94-V0)
Tel: 86-20-38601850
Short circuit protection* Continuous, Auto-recovery
Fax:86-20-38601272
Http://www.mornsun-power.com MTBF 1940 K hours
Weight 2.3 g

The copyright and authority for the interpretation of the products are reserved by MORNSUN Specifications subject to change without notice.
E_S-1WR & F_S-1WR B/0-2012 Page 1 of 3
 INPUT SPECIFICATIONS TYPICAL CHARACTERISTICS
Item Test conditions Min. Typ. Max. Units
3.3V input 50/420
5V input 30/260
Input current
12V input 12/110 mA
(No load/Full load)
15V input 12/100
24V input 7/55
3.3V input 7
5V input 9
Surge voltage
12V input 18 V
(1S max)
15V input 21
24V input 30

OUTPUT SPECIFICATIONS
Item Test conditions Min. Typ. Max. Units
Output power 0.1 1 W
Line regulation For Vin change of ±1% ±1.1 ±1.5
%
Load regulation 10% to 100% load 10 20
Output voltage accuracy Follow the tolerance envelope graph
Temperature drift 100% full load ±0.03 %/°C Operating Temp.(oC)
Ripple & Noise* 20MHz Bandwidth 100 200 mVp-p
Switching frequency Full load, nominal input 100 kHz RECOMMENDED CIRCUIT
*Test ripple and noise by “parallel cable” method. See detailed operation instructions at Testing D u al Ou tpu t
L L
of Power Converter section, application notes. +Vo
Vin Cout
Cin DC DC 0V
L Cout
ISOLATION SPECIFICATIONS GND
-Vo
Item Test conditions Min Typ Max Units Sin gle Ou tp ut
L
L +Vo
Isolation voltage Tested for 1 minute and 1 mA max 3000 VDC Vin
Cin DC DC Cout
Isolation resistance Test at 500VDC 1000 MΩ GND
0V
Isolation Capacitance Input/Output,100KHz/0.1V 6 15 PF
(Figure 1)
D ual Output
APPLICATION NOTE REG +Vo
Vin REG

① Requirement on output load DC DC 0V

GND
To ensure this module can operate efficiently and reliably, During operation, the REG -Vo
minimum output load is not less than 10% of the full load. If the actual output power is very
Single Output
small, please connect a resistor with resistance of 10% rated power at the output end in
REG +Vo
parallel, or use our company’s products with a lower rated output power Vin REG
DC DC
② Overload Protection GND
0V
Under normal operating conditions, the output circuit of these products has no protection
(Figure 2)
against overload. The simplest method is to connect a slow-blow fuse in series at the input
end or add a circuit breaker to the circuit.
Recommended capacitance(Table 1)
③ Recommended testing and application circuit Vin Cin Single Cout Dual Cout
If you want to further decrease the input ripple or the input inrush current, an “LC” (VDC) (μF) output (μF) output (μF)
filtering network may be connected to the input and output ends of the DC/DC converter, (VDC) (VDC)
see (Figure 1).
5 4.7 5 10 ±5 4.7
It should also be noted that the inductance and the frequency of the “LC” filtering
network should be staggered with the DC/DC frequency to avoid mutual interference. 12 2.2 9 4.7 ±9 2.2
However, the capacitance of the output filter capacitor must be proper. If the capacitance is 15 2.2 12 2.2 ±12 1
too big, a startup problem might arise. For every channel of output, provided the safe and
reliable operation is ensured, the recommended capacitance of its filter capacitor sees 24 1 15 1 ±15 0.47
(Table 1). 1.The recommended external capacitance please use
the ceramic capacitor;
④ Output Voltage Regulation and Over-voltage Protection Circuit 2. For applications where output power is less than
The simplest device for output voltage regulation, over-voltage and over-current 0.5W in reality, external capacitors are not
protection is a linear voltage regulator with overheat protection that is connected to the recommended.
input or output end in series (Figure 2).

⑤ No parallel connection or plug and play

The copyright and authority for the interpretation of the products are reserved by MORNSUN Specifications subject to change without notice.
E_S-1WR & F_S-1WR B/0-2012 Page 2 of 3
 OUTLINE DIMENSIONS & pIN CONNECTIONS

MECHANICAL DIMENSIONS RECOMMENDED FOOTPRINT

19.50±0.50 15.24
[0.768±0.020 ] 2.13
[0.084] [0.600]
10.16
[0.400]

[0.366±0.008]
[0.354±0.008]
9.30±0.20
9.00±0.20

[0.528±0.020]
13.40±0.50
(Front View)

1 2 5 6 7 1 2 5 6 7

[0.075±0.008]
1.90±0.20
∅1.00
[0.040]

10.16
0.6±0.10 [0.400]
[0.024±0.004 ] 15.24 Note: grid 2.54*2.54mm.
[0.600]
[0.075±0.008]
1.90±0.20

TUBE OUTLINE DIMENSIONS

[0.024±0.008]
[0.700]

0.60±0.20
1.75
(Bottom View)
8.30[0.327]

2.13
[0.084]
[0.012±0.004]
0.30 ±0.10

11.70[0.461]
17.50[0.689]
(Side View)

F OOTP RINT DETAI LS

PIN Single Dual
5.00 [0.197]
1 Vin Vin
2 GND GND Note :
5 0V -Vo Unit : mm[inch]
General tolerances:± 0.50mm[ ± 0.020inch]
6 No Pin 0V L=530mm[20.866inch] Devices per tube quantity: 25pcs
7 +Vo +Vo L=220mm[8.661inch] Devices per tube quantity: 10pcs
Short tube inner package dimensions: 255*170*80mm
Short tube outer package dimensions
(with six inner package box): 375*280*270mm
Note : Long tube inner package dimensions: 580*200*100mm
Unit : mm[inch] Long tube outer package dimensions
Pin section tolerances :±0.10mm[± 0.004inch]
(with two inner package box): 600*215*220mm
General tolerances:± 0.25mm[ ± 0.010inch ]
Long tube outer package dimensions
(with three inner package box):600*215*325mm

Note:
1. Operation under minimum load will not damage the converter; However, they may not meet all specification listed, and that will reduce the life
of product.
2. All specifications measured at Ta=25°C, humidity<75%, nominal input voltage and rated output load unless otherwise specified.
3. In this datasheet, all the test methods of indications are based on corporate standards.
4. Only typical models listed, other models may be different, please contact our technical person for more details.

The copyright and authority for the interpretation of the products are reserved by MORNSUN Specifications subject to change without notice.
E_S-1WR & F_S-1WR B/0-2012 Page 3 of 3