Syllabus for Internet of Things

Summer Training
Unit-1 Introduction to Embedded Systems and IoT Contact Hours:30
Embedded Systems Embedded system: Introduction to Microcontroller, Difference between
and its microprocessor and Microcontroller, Difference between Embedded system and
IoT.
Introduction to IoT Introduction to IoT and its architecture, Importance of the Internet of Things (IoT)
and Raspberry Pi in Society, Introduction of Raspberry Pi, Pin Diagram of Raspberry, Comparison
and Arduino of Arduino and Raspberry Pi.
Arduino: Birth, Open-Source community: Features of Arduino Uno, Functional
pin diagram of Arduino UNO, the Basic skeleton of Arduino programming,
Function of Arduino- Setup and Loop functions, variables, Constants, and their
Week 1 scopes.
Experiment 1 Design first sketch to interface Led with Arduino Uno and to design different
patterns using delay and without delay (millis) function.
Experiment 2 Design the circuit and WAP to interface the Switches and push buttons using pull-
up and pull-down resistors with Arduino.
Experiment 3 Design the circuit and WAP to interface with 16*2 LCD using I2C with Arduino
Uno to print the message on LCD.
Basic Electronics Introduction to Active and Passive Elements: Resistors(R), Capacitors(C),
Components Inductors(L), Transistors, Ohm’s Law, Voltage and Current Divider rule,
Importance of Pull up and Pull-down resistors

Interfacing of Digital: Seven Segment Display, Relay (SPDT), DHT11sensor.

Week 2 Devices Analog: Interfacing of LDR (Photoresistor) with Arduino, Temp. sensor (LM35).
Experiment 4 Design the circuit and WAP to interface an ultrasonic sensor (SR-04) with Arduino
Uno to measure distance and print on LCD.
Experiment 5 Design the circuit and WAP to interface the RFID card and reader with Arduino
Uno.
Embedded System Introduction to Node MCU, Pin diagram, Programming of Node MCU,
Applications Introduction of cloud (BLYNK/Thingspeak/Cayenne), Connecting NodeMCU to
WIFI network and cloud, Collect and analyze data of sensors over the cloud.
Week 3 Interfacing of LEDs with NodeMCU.
Experiment 6 Interfacing NodeMCU with sensors (Gas Sensor/ Ultrasonic
sensor/DHT11/TMP36) and actuators and getting data over the cloud.
Experiment 7 Design the circuit and WAP to interface the DC motor /Servo Motor using a
motor-driven IC and using Arduino Uno.
Experiment 8 Design the circuit and WAP to interface the Bluetooth (HC-05) with Arduino Uno
or NodeMCU.
Design smart home systems, Smart parking systems, Smart dustbins for a clean
environment, Water level controller systems, and other various applications.
Design one live project on the basis of sensors and microcontroller Arduino Uno
Week 4 Applications of IoT or Node MCU.
and Project
 Syllabus for Internet of Things
Summer Training
Day Wise Syllabus - Week 1
Days Topic Sub-Topic Contact Hours(15 Hrs)
Introduction to Embedded System, Difference 1.5 Hrs
Embedded between Microprocessor and Microcontroller,
System and IoT Examples of Microprocessor and Microcontrollers
Day 1 Difference between Embedded System and IoT, 1.5 Hrs
Example of embedded system and IoT
Introduction to IoT and its architecture, Importance 1.5 Hrs
Introduction to of the Internet of Things (IoT) in Society,
Day 2 IoT and
Raspberry Pi Introduction to Arduino Uno board, Pin diagram and 1.5 Hrs
and Arduino architecture of Uno, Difference between RPi and
Arduino Uno
The first program and basic skeleton of Arduino IDE, 1 Hrs
Programming Download and installation of Arduino IDE.
Day 3 and first Sketch Introduction to Tinkercad Software
of Arduino Interfacing of Arduino with Led and generate it 2 Hrs
random pattern (Circuit Design and Coding),
Experiment 1 Difference between digital and PWM pins of Uno
Week 1
Worksheet and Assignment related to interfacing of 1.5 Hrs
Assignment 1 LED. Interfacing of pushbutton with Arduino uno,
and Difference between pushbutton and switch
Experiment 2 Concept of pull up and pull-down resistor, Difference 1.5 Hrs
Day 4 between pull up and pull-down resistor. Controlling
of Led with pushbutton
Introduction to Introduction to LCD (16*2), pinout of LCD, 2 Hrs
LCD Difference between UART and I2C protocol,
Day 5 Interfacing of LCD with Arduino Uno
Experiment 3 Interfacing of LCD with Arduino uno and print data 1 Hrs
on display using UART and I2C protocol.
Total Hours (Week 1) 15 Hrs
 Syllabus for Internet of Things
Summer Training
Day Wise Syllabus - Week 2
Days Topic Sub-Topic Contact Hours
Introduction to basics of electronics, Difference 1 Hrs
Basic between active and passive elements.
Electronics Introduction to Resistor, Capacitor and Inductor 2 Hrs
Day 6 concepts elements, Ohm's Law and its applications. Examples
of Ohm’s law. Series and parallel connections of
resistors
Introduction and difference between voltage and 1.5 Hrs
Basic current divider rule. Implementation of current and
Day 7 electronics and voltage divider circuits.
gas sensor Introduction to Gas Sensors, Working and Types of 1.5 Hrs
interfacing gas sensors, Interfacing of gas sensors with Arduino
and its code.
Introduction to seven-segment display, types of 1 Hrs
Week 2 Seven Segment seven-segment display. Difference between common
Day 8 display and its cathode and common anode seven segment display.
interfacing
Introduction Interfacing of seven-segment display in the common 2 Hrs
and interfacing anode and common cathode configuration,
of LDR Interfacing of LDR with Arduino.
Worksheet Discussion of worksheet and Assignment related to 1 Hrs
Day 9 Interfacing of gas sensor and seven-segment display
Experiment 4 Introduction to ultrasonic sensor and its working. 2 Hrs
interfacing of ultrasonic sensor with Arduino.
Introduction to Introduction to relay and difference between SPDT 2.5 Hrs
relay and DPDT relay. Interfacing of relay with Arduino
Day 10 uno and control appliances.
Worksheet Discussion on worksheet related to LCD interfacing. 0.5 Hrs

Total Hours (Week 2) 15 Hrs

 Syllabus for Internet of Things
Summer Training
Day Wise Syllabus - Week 3
Days Topic Sub-Topic Contact Hours
Introduction to RFID, Types of RFID, Difference 2 Hrs
RFID between Active and Passive RFID, Interfacing of
interfacing and RFID reader/writer with Arduino uno
Day 11 Experiment 5

Introduction to Introduction of NodeMCU, Difference between 0.5 Hrs

NodeMCU Arduino uno board and NodeMCU,
Introduction to Introduction to Blynk cloud, Login and designing of 1 Hrs
Cloud template in Blynk cloud.
Day 12
NodeMCU Installation of Libraries and board for NodeMCU 2 Hrs
board (Esp8266) in Arduino IDE, First sketch of
NodeMCU interfacing.
Controlling of LED from remote location using cloud 1 Hrs
Week 3 Interfacing of Interfacing of ultrasonic sensor with NodeMCU and 2 Hrs
Day 13 Blynk cloud getting data over cloud.
with NodeMCU
DC Motor Introduction to motor driven IC, Motor driven 2 Hrs
Shield, Interfacing of DC motor with Arduino
Day 14 Servo motor Interfacing of servo motor with Arduino uno and 1.5 Hrs
and NodeMCU. Controlling of servo motor from remote
Experiment 7 location.
Introduction to Introduction to Bluetooth and interfacing of 2 Hrs
Bluetooth and Bluetooth with Arduino uno to control appliances
Day 15 Experiment 8 like light, fan etc.
Temperature Introduction to Temperature and DHT11 Sensor and 1 Hrs
Sensor its interfacing with NodeMCU and Uno board
Total Hours (Week 3) 15 Hrs
 Syllabus for Internet of Things
Summer Training
Day Wise Syllabus - Week 3

Days Topic Sub-Topic Contact Hours

Live Project Design one live project on the basis of sensors and 15 Hrs
microcontroller Arduino Uno or Node MCU.

Week 4
Total Hours (Week 1) 15 Hrs

Sno Week Contact Hrs

1. Week 1 15 Hrs
2. Week 2 15 Hrs
3. Week 3 15 Hrs
4. Week 4 15 Hrs
Total 60 Hrs