ISO 7005-2-1988 - Cast Iron Flanges 1

IS0
INTERNATIONAL STANDARD 7005-2

First edition
1988-12-H
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION

ORGANISATION INTERNATIONALE DE NORMALISATION
MEXAYHAPOAHAR OPrAHM3A~MR n0 CTAHAAPTMSA~MM
Metallic flanges -
Part 2 :
Cast iron flanges
Brides m&alliques -
Partie 2: Brides en fonte
Reference number
IS0 7005-2: 1988 Q
--`,`,````,`,,`,,,,,`,`,``,,,`-`-`,,`,,`,`,,`---
Copyright International Organization for Standardization

Provided by Accuris under license with AENOR Licensee=JGC Philippines/5978460008, User=Fernandez, Renato
No reproduction or networking permitted without license from Accuris Not for Resale, 07/24/2023 01:25:38 MDT
IS0 7005-2 : 1988 (El
Contents
Page
. ..
Foreword .............................................................. III
Introduction ............................................................ iv
Section 1: General ..................................................... 1
1.1 Scope ............................................................ 1
1.2 Normative references ............................................... 1
1.3 Definitions and designations ......................................... 1
Section 2: General requirements ........................................ 3
2,l Pressure/temperature (p/T) ratings ................................... 3
2.2 Materials .......................................................... 3
2.3 Dimensions ........................................................ 3
2.4 Joint facings ....................................................... 3
2.6 Spot-facing or back-facing ........................................... 4
2.6 Marking ........................................................... 4
2.7 inspection and test ................................................. 4
2.8 Repairs ........................................................... 4
2.9 Information to be supplied by the purchaser ............................ 4
Section 3: Dimensions ................................................. 7
Section 4: Materials and pressure/temperature (p/T) ratings ............. 29
4.1 Materials .......................................................... 29
4.2 Pressure/temperature ratings ........................................ 30
Annexes
A Guidance on tolerances of dimensions .................................. 32
34
0 International Organization for Standardization, 1988 l
Printed In Switzerland
ii --`,`,````,`,,`,,,,,`,`,``,,,`-`-`,,`,,`,`,,`---

IS0 7005-2 :I988 (EI
--`,`,````,`,,`,,,,,`,`,``,,,`-`-`,,`,,`,`,,`---
Foreword
IS0 (the international Organization for Standardization) is a worldwide federation of
national standards bodies (IS0 member bodies). The work of preparing international
Standards is normally carried out through IS0 technical committees. Each member
body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. international organizations, govern-
mental and non-governmental, in liaison with ISO, also take part in the work. IS0
collaborates closely with the international Eiectrotechnicai Commission (IEC) on all
matters of eiectrotechnical standardization.
Draft International Standards adopted by the technical committees are circulated to

the member bodies for approval before their acceptance as international Standards by
the IS0 Council. They are approved in accordance with IS0 procedures requiring at
least 75 % approval by the member bodies voting.
International Standard IS0 705-2 was prepared by Technical Committee iSO/TC 5,

Ferrous metal pipes and metallic fittings.
This part of IS0 7995, together with parts 1 and 3, cancel and replace IS0 2084 : 1974,
IS0 2229 : 1973 and IS0 2441 : 1975.
IS0 7095 will consist of the following parts, under the general title Metallic f/anges:
- Part 1: Steel flanges
- Part 2: Cast iron flanges
- Part 3 : Copper alloy and composite flanges
- Part 4: Aiuminium and aiuminium alloy flanges
Annexes A and B of this part of IS0 7905 are for information only.

IS0 7005-2 : 1988 (El
Introduction
Various flange systems based on differing design criteria have been in use throughout
the world for many years. Given the increasing difficulties arising from such a situation,
this international Standard has been based on a single series of metallic flanges.
IS0 7005 will be published in four parts as follows :
Part 1 : Steel flanges
Part 2: Cast iron flanges

Part 3 : Copper alloy and composite flanges
Part 4: Aluminium and aluminium alloy flanges
This part of IS0 7005 is based on the American and European cast iron flange systems
which have been combined to produce one International Standard with some changes
to the dimensions specified in the two systems.
The materials specified in American (ANSI) standards and international Standards

have been retained. Because, at this time, the International Standards for cast iron
materials do not specify pressure/temperature (p/T) ratings, the ratings for the
materials specified have been based on those given in comparable national standards.
in the American system, flanges are designated by a Class rating but in this part of
IS0 7005 the relevant Class ratings are designated by nominal pressure (PN) ratings.
The equivalent designations are as follows :
Classes 125 and 150: IS0 PN20
Classes 250 and 300: IS0 PN50
The ratings used in the European system remain as IS0 PN2,5, IS0 PN6, IS0 PNIO,
IS0 PN16, IS0 PN25 and IS0 PN4O.
IS0 PN20 and IS0 PNSQ grey cast iron and ductile cast iron flanges am designed to be
interchangeable with flanges to ANSI 816.1 (grey cast iron) and ANSI 816.42 (ductile
cast iron). They are not identical but are deemed to comply with the dimensions
specified in ANSI 816.1 and ANSI 816.42 as appropriate (see 2.7).
Flange details in ail four parts of IS0 7005 are such that flanges having the same PN
and nominal size (DN) values and compatible flange facings will mate together when
using metric bolting. Tolerances on dimensions are given for guidance in annex A.
To avoid any possible confusion in giving descriptive names to flanges, all flanges are
designated by type numbers and flange facings are designated by a letter.
Users of this part of IS0 7005 should satisfy themselves that the flanges comply with
--`,`,````,`,,`,,,,,`,`,``,,,`-`-`,,`,,`,`,,`---
any statutory requirements,

INTERNATIONAL STANDARD IS0 7005-2 : 1988 (E)
Metallic flanges -
Part 2:
Cast iron flanges
Section 1: General
1.1 Scope of the standards listed below. Members of IEC and IS0 main-
tain registers of currently valid International Standards.
This part of IS0 7665 for a single system of flanges specifies re-
quirements for circular grey, malleable and ductile cast iron IS0 166 : 1969, ClassrYkation of grey cast iron.
flanges in the following nominal pressure ratings: IS0 997 : 1963, plain washers for metric bofts, screws and
nuts - Genera/plan.
Series I* Series 2*
IS0 PNIO IS0 PN2,5 IS0 1693 : 1967, Spheroidalgraphite cast iron - Classification.
IS0 PN16 IS0 PN6 IS0 2531 : 1966, Ductile iron pipes, fittings and accessories for
IS0 PN20 IS0 PN25 pressure pipelines.
IS0 PN56 IS0 PN46
IS0 6922 : 1961 I Malleable cast iron.
This part of IS0 7665 specifies the types of flanges and their
facings, dimensions, bolt sizes, surface finish of faces, mark- IS0 6769 : 1980, Pipe components - Definition of nominal
ing, testing, inspection and materials together with associated size.
pressure/temperature ratings. IS0 7269 : 1963, Pipe components - Definition of nominal
pressure.
NOTES
ASTM A 126 : 1964, Gray iron castings for valves, flanges, and
1 Attention is drawn to the need to refer to the pressure/temperature pipe fittings.
rating tables for the permissible working pressures, particularly for
flanges of IS0 PN20 and IS0 PN50. ASTM A 395 : 1960, Ferritic ductile iron pressure-retaining
2 Dimensions of gaskets will be the subject of a future International castings for use at elevated temperatures,
Standard.
1.3 Definitions and designations
1.2 Normative references
1.3.1 Definitions
The following standards contain provisions which, through
For the purposes of this part of IS0 7665, the definitions of
reference in this text, constitute provisions of this part of
nominal size (DNj as given in IS0 6766, and nominal pressure
IS0 7665. At the time of publication, the editions indicated
(PNj as given in IS0 7266, apply.
were valid. All standards are subject to revision, and parties to
agreements based on this part of IS0 7005 are encouraged to NOTE - In this part of IS0 7005, nominal pressure is designated by the
investigate the possibility of applying the most recent editions letters “IS0 PN” followed by the appropriate reference number.
l Series 1 ratings are the basic ratings; series 2 ratings have limited application.
--`,`,````,`,,`,,,,,`,`,``,,,`-`-`,,`,,`,`,,`---
1
IS0 70052 : 1988 (El
1.3.2 Designation of types and facings 13 - Hubbed threaded flange
14 - Hubbed socket welding flange

Figure 1 illustrates flanges identified according to type.
15 - Loose hubbed flange for lapped pipe end
05 - Blank flange
21 - Integral flange
11 - Welding neck flange Figure 2 illustrates facing types (type A and type Bj which are
used where applicable in conjunction with flanges shown in
12 - Hubbed slip-on flange for welding figure I.
--`,`,````,`,,`,,,,,`,`,``,,,`-`-`,,`,,`,`,,`---

IS0 7005-2 : 1988 (EI
Section 2 : General requirements
2.1 Pressure/temperature (p/T) ratings 2.2.3 Bolting
NOTES
2.1.1 General
1 Bolting materials are not within the scope of this part of IS0 7905
but materials for bolting should be chosen by the user according to the
The pressure/temperature ratings of the flanges manufactured pressure, flange material and the selected gasket so that the flanged
from the materials specified in table 14 shall be the maximum joint remains tight under the expected operating conditions.
allowable non-shock working pressures at the temperatures
2 For joints comprising grey cast iron flanges with raised faces, and
given in tables 15 (grey cast iron), 16 and 17 (ductile cast iron)
where grey cast iron flanges are bolted to flanges of other materials
and 18 (malleable cast iron). Linear interpolation is permitted and either or both of the flanges have a raised face, it is recommended
for intermediate temperatures. that bolting having a yield strength not exceeding 240 N/mm* should
be used. If higher strength bolting is used, it is recommended that
NOTE - The rating of a flange is not necessarily the rating of the mating flanges should have flat faces and that full-face gaskets, which
whole pipework system. extend to the outside diameter of the flange, should be used.
2.3 Dimensions
2.1.2 Rating of flanged joints
2.3.1 Range of nominal sizes
Where two flanges in a flanged joint do not have the same
pressure/temperature rating, the rating of the joint at any The range of nominal sizes applicable to each flange type and
temperature shall not exceed the lower of the two flange to each pressure rating shall be as specified in tables 2 to 4 as
ratings at that temperature. appropriate.
NOTES 2.3.2 Dimensional details

1 The temperature shown for a corresponding pressure rating is con-
sidered to be the same as that of the contained fluid. Use of a pressure Dimensions of flanges shall be in accordance with the following
rating corresponding to a temperature other than that of the contained tables, as appropriate :
fluid is the responsibility of the user, subject to the requirements of any
applicable code or regulation. table 6 for IS0 PN2,5 flanges
2 Application of the ratings given in this part of IS0 7005 to flange table 7 for IS0 PN6 flanges
joints should take into consideration the risk of leakage due to forces
and moments developed in the connecting pipework. table 8 for IS0 PNlO flanges
3 Owing to the nature of any thread sealant used, additional limi- table 9 for IS0 PN16 flanges
tations may be placed on a threaded flange. table 10 for IS0 PN20 flanges
4 These notes on service considerations are not intended to be table 11 for IS0 PN25 flanges
exhaustive.
table 12 for IS0 PN46 flanges
table 13 for IS0 PN59 flanges
2.2 Materials
NOTE - Tolerances on dimensions are not specified in this part of
IS0 7005 but guidance on the dimensions which should have
2.2.1 Range of materials tolerances and suggested tolerances are given in annex A.
Flanges shall be manufactured from the materials specified in

table 14.
2.3.3 Attachment of welded and threaded flanges
NOTE - Details of attachment for welded and threaded flanges are

NOTES not specified in this part of IS0 7005.
1 It is the responsibility of each national standards organization to
determine which are the national materials equivalent to materials
2.4 Joint facings
specified in this part of IS0 7005.
--`,`,````,`,,`,,,,,`,`,``,,,`-`-`,,`,,`,`,,`---
2 Where there is an appropriate application standard, it is the 2.4.1 Types of facings

responsibility of the purchaser to ensure compliance with the re-
quirements of that standard.
The flange facings specified (flat face type A and raised face
type B) are illustrated in figure 2; their raised face dimensions
shall be as given in table 5.
2.2.2 Gaskets
NOTE - The transition from the outside diameter of the raised face to
The various types, dimensions and materials used for gaskets the flange face is at the option of the manufacturer (i.e. either a radius
are not within the scope of this part of IS0 7965. or a chamfer may be used).
3
IS0 700!%2 :I983 (E)
2.4.2 Application 2.6 Marking
2.4.2.1 IS0 PN2,5, is0 PN6, IS0 PNIO, is0 PN16, 2.6.1 Identification
IS0 PN25 and IS0 PN46 flanges made of grey cast iron and
ductile cast iron shall have raised faces. Flanges other than integral shall be clearly marked as follows :
a) the nominal size (DNI and the nominal pressure rating

2,4.2,2 IS0 PN20 flanges made of grey cast iron shall have (IS0 PN);
flat faces. IS0 PN56 flanges made of grey cast iron shall have
raised faces unless otherwise specified. b) material designation;
IS0 PN20 and IS0 PN56 flanges made of ductile cast iron shall c) manufacturer’s name or trade-mark.
have raised faces unless otherwise specified.
EXAMPLE
2.4.2.3 Flanges made in malleable cast iron shall have either DN 300 IS0 PN16 400-5 XXXX
al fiat faces, or NOTES

1 Additionally, flange facing designations may be given.
bl raised faces.
2 Where a flange is subsequently used to form an integral part of a
component and the component has a lower pressure rating than that of
2.4.3 Surface finish of flanges the flange, the lower rating should be clearly marked on the compo-
nent and the lowest p/T rating will apply.
All flange jointing faces shall be finished in accordance with
table 1. The faces shall be compared by visual or tactile means 2.6.2 Stamping
with reference specimens which conform with the R, and R,
values given in table 1. Where steel stamps are used, the marking shall be positioned
on the rim of the flange.
NOTES
1 It is not intended that instrument measurements are taken on the
2.7 Inspection and test
flange faces, and the R, and R, values as defined in IS0 469 : 1982,
Surface roughness - Parameters, their values and general rules for
specifying requirements, relate to the reference specimens. IS0 PN20 and IS0 PN56 flanges specified are designed to be
interchangeable with, but not identical to, grey cast iron
2 Other finishes may be agreed between the manufacturer and pur-
Class 125 and Class 256 flanges to ANSI B16.1 respectively
chaser.
and with ductile cast iron Class 156 and Class 366 flanges to
ANSI 816.42 respectively.
Table 1 - Numerical values of the surface finish
parameters, R, and R,, of flange faces NOTES
Values in micrometres 1 It is recommended that IS0 PN26 and IS0 PNXI flanges be ac-
cepted by inspectors as complying with the dimensions specified in
--`,`,````,`,,`,,,,,`,`,``,,,`-`-`,,`,,`,`,,`---
Manufacturing
process 4 RZ ANSI 816.1 or ANSI 816.42 as appropriate.
I I I
2 This part of IS0 7005 does not make provision for routine inspec-
Turning 11 I 3,2 to 12,6 1 12,5 to 56 1
tion or pressure testing of separate flanges. However, flanges may be
Other*) 3,2 to 6,3 12,5 to 25 required to be pressure tested after attachment to a pipe or other
I equipment or when forming an integral part of such equipment. The
1) “Turning” covers any method of machine operation producing test pressure is then dependent on the requirements of the appropriate
either serrated concentric or serrated spiral grooves. standard or code of practice in accordance with which the equipment
2) Processes other than turning are permissible provided that they has been manufactured.
give a surface finish in compliance with the R, and R, values
specified.
2.6 Repairs
Where not otherwise prohibited by the applicable material stan-

2.5 Spot-facing or back-facing dard or codes and regulations, repairs by welding are permitted
for ductile cast iron. All welding repairs shall be carried out in
Any spot-facing or back-facing required shall not reduce the
accordance with a written procedure.
flange thickness to less than the thickness specified. When
spot-facing is usedl the diameter shall be large enough to
accommodate the outside diameter of the equivalent normal 2.9 information to be supplied by the purchaser
series of washers complying with IS0 637 for the bolt size
being fitted. When a flange is back-faced, it is permissible for The following information should be supplied by the purchaser
the fillet radius to be reduced but it shall not be eliminated in the enquiry and/or order:
entirely. The bearing surfaces for the bolting shall be parallel to
the flange face within 2O. a) number of this part of IS0 7665, i.e. IS0 76652;

IS0 7005-2 : 1588 (El
b) nominal size - DN followed by the appropriate number f) material designation (see 2.2.1);
(see 2.3.1);
g) for flange types 11, 12, 14 and 15, the external diameter
c) nominal pressure - IS0 PN followed by the ap- and thickness of pipe to which the flange is to be attached
propriate number (see 1.1); (see note 3 to tables 6 to 13) when supplied loose, i.e. not as
a component of some other fitting;
d) flange type number (see 1.3.2 and figure 1);
h) type of thread for threaded flanges (type 13) when sup-
e) facing type letter (see 1.3.2 and figure 2); plied loose, i.e. not as a component of some other fitting.
For IS0 PN20 IS0 PN50

flanges only
Blank flange
NOTE - See the note to 2.4.1 regarding the transition from the outside diameter of the raised face.
Figure 1 - Types of flanges
--`,`,````,`,,`,,,,,`,`,``,,,`-`-`,,`,,`,`,,`---
5
IS0 700!!-2 : 1988 (El
Type 11 Type 12
Welding neck flange Hubbed slip-on flange for welding
Type 13 Type 14
Hubbed threaded flange Hubbed socket welding flange
Type 15 Type 21
Loose hubbed flange for lapped pipe end Integral flange
NOTE - See the note to 2.4.1 regarding the transition from the outside diameter of the raised face.
Figure 1 - Types of flanges bncludedl
--`,`,````,`,,`,,,,,`,`,``,,,`-`-`,,`,,`,`,,`---

IS0 7005-2 : 1988 (E)
i3
c
--`,`,````,`,,`,,,,,`,`,``,,,`-`-`,,`,,`,`,,`---
I , I I I , , ,
I I

IS0 700!5-2 :I988 (E)
GQZ 1
oool
006
oos
ML I I IIIII III I I I I I I I I I I I Illll III I I
--`,`,````,`,,`,,,,,`,`,``,,,`-`-`,,`,,`,`,,`---

IS0 7005-2 : 1988 (El
--`,`,````,`,,`,,,,,`,`,``,,,`-`-`,,`,,`,`,,`---
I
,

9
IS0 7005-2 1988(El
OOZE
oooc
OOSZ
0091
OOPZ
oozz
0001
0091
oobl
ooz 1
oool
0%
OOE
OGZ
OOZ
091
9ZC
001
oa
99
09
ob
ZE
91
01
91
01
E
L
/ s
3!
%
*
z"
Q)
I-2
--`,`,````,`,,`,,,,,`,`,``,,,`-`-`,,`,,`,`,,`---

IS0 7005-2 : 1988 (E)
Type A Type B
Flat face Raised face
Figure 2 - Flange facing types A and B *)
Table 5 - Dimensions for type B flange facings ‘1
’ IS0 PN2.5 IS0 PN6 IS0 PNIO IS0 PN16 IS0 PN26 IS0 PN25 IS0 PN46 IS0 ‘N50
Nominal I I I I I I I I I I
size Grey cast Ductile cast
-L4
iron iron
DN fl 4 fl 4 fl 4 fi 4 4 fl 4 fl 4 fl
IO 33 2 41 2 41 2 -c 41 2
15 38 2 48 2 46 2 46 2 48 2
m 48 2 56 2 56 2 56 2 56 2
25 58 3 65 3 65 3 51 65 3 65 3 68 2 51 2
32 69 3 76 3 76 3 64 76 3 76 3 78 2 64 2
40 78 3 84 3 84 3 73 84 3 84 3 80 2 73 2
50 88 3 88 3 89 3 92 88 3 88 3 106 2 92 2
65 108 3 118 3 118 3 105 118 3 118 3 125 2 105 2
80 124 3 132 3 132 3 127 132 3 132 3 144 2 127 2
100 144 3 156 3 156 3 157 156 3 156 3 176 2 157 2
125 174 3 184 3 184 3 186 184 3 184 3 211 2 186 2
Use
150 199 3 211 3 211 3 216 211 3 211 3 246 2 216 2
IS0 PN6
200 254 3 266 3 266 3 270 274 3 284 3 303 2 270 2
dimensions
250 308 3 319 3 319 3 324 3303 345 3 357 2 324 2
353 4 370 4 370 4 381 3894 408 4 418 2 382 2
413 4 429 4 429 4 413 4484 465 4 481 2 413 2
463 4 480 4 480 4 470 5034 535 4 2 470 2
518 4 530 4 548 4 533 5484 560 4 E 2 633 2
569 4 582 4 609 4 584 6094 615 4 648 2 584 2
667 5 682 5 720 5 692 720 5 770 2
772 5 794 5 794 5 820 5 9452) 2
878 5 801 5 901 5 928 5
978 5 1001 5 1001 5 1028 5
1078 5 1 112 5 1 112 5 1140 5
1295 5 1328 5 1328 5 1350 5
1400 1480 5 1 510 5 1530 5 1530 5 1560 5
1600 1690 5 1710 5 1750 5 1750 5 1780 5
1800 1890 5 1918 5 1950 5 1950 5 1985 5
2OGil 2090 5 2125 5 2160 5 2150 5 2210 5
2200 2295 6 2335 6
2400 2495 6 2545 6
2600 2695 6 2750 6
2800 2910 6 2960 6
3000 3 110 6 3160 6
3200 3 310 6 3370 6
3400 3 510 6 3580 8
3600 3 720 6 3790 6
3800 3 920 6
4000 4 120 6
- i
1) See 2.4.2.
2) For IS0 PN5Oflanges, nominal size DN 750is used instead of DN 700.
*) For application see2.4.2.
--`,`,````,`,,`,,,,,`,`,``,,,`-`-`,,`,,`,`,,`---
11
IS0 7005-2 : 1988 (E)
--`,`,````,`,,`,,,,,`,`,``,,,`-`-`,,`,,`,`,,`---
12
IS0 70052 :I988 CE)
13
--`,`,````,`,,`,,,,,`,`,`

IS0700!%2:1988 (E)
14 --`,`,````,`,,`,,,,,`,`,``,,,`-`-`,,`,,`,`,,`---

IS0 7005-2 : 1958 (E)
El
N
uo!gdo spmmepue~
--`,`,````,`,,`,,,,,`,`,``,,,`-`-`,,`,,`,`,,`---
15
ISO7005-2:1666 (E)
r-l
EN
16 --`,`,````,`,,`,,,,,`,`,``,,,`-`-`,,`,,`,`,,`---

IS0 7005-2 :I988 (E)
--`,`,````,`,,`,,,,,`,`,``,,,`-`-`,,`,,`,`,,`---
17
IS0 7005-2 : 1988 (El
I-
18 --`,`,````,`,,`,,,,,`,`,``,,,`-`-`,,`,,`,`,,`---

IS0 700!5-2 : 1988 (EI
-
s
-
-
R
-
to
5
-
--`,`,````,`,,`,,,,,`,`,``,,,`-`-`,,`,,`,`,,`---
d
-
z
-
-
B
-
B
19
IS0 700!5-2 : 1988 (E)
--`,`,````,`,,`,,,,,`,`,``,,,`-`-`,,`,,`,`,,`---

IS0 7005-2 : 1988 (E)
--`,`,````,`,,`,,,,,`,`,``,,,`-`-`,,`,,`,`,,`---

21
IS0 70052 : 1988 (El
--`,`,````,`,,`,,,,,`,`,``,,,`-`-`,,`,,`,`,,`---

IS0 7005-2 : 1988 (El
--`,`,````,`,,`,,,,,`,`,``,,,`-`-`,,`,,`,`,,`---
E
-
-
lo.
w
-
-
35
-
3
-
% ,
I
-
%
-
,
8 ,
,

IS0 7005-2 : 1988 (E)
t--T-l
--`,`,````,`,,`,,,,,`,`,``,,,`-`-`,,`,,`,`,,`---

24
IS0 7005-2 : 1999 (EI
.E
E
2
E
E
E
I si i i i i i i i i i i i i i i i i i i i I I
--`,`,````,`,,`,,,,,`,`,``,,,`-`-`,,`,,`,`,,`---
1
.E P)
E .N x
On
2
-
25
IS0 7005-2 : 1988 (El
--`,`,````,`,,`,,,,,`,`,``,,,`-`-`,,`,,`,`,,`---

IS0 70052 : 1988 (El
--`,`,````,`,,`,,,,,`,`,``,,,`-`-`,,`,,`,`,,`---

IS0 7666-2 : 1966 (EI
Notes to tables 6 to 13
1 All IS0 PNs: For dimensions dt andft, see table 5.
2 IS0 PN2,5, IS0 PN6, IS0 PNIO, IS0 PN16, IS0 PN25 and IS0 PN4O: The ductile, grey and malleable cast iron flange thicknesses specified are :
Ca, grey cast iron thicknesses to DIN 2530, DIN 2531, DIN 2532, DIN 2533, DIN 2534 and DIN 2535;
C,, ductile cast iron thicknesses to IS0 2531;
Cs, malleable cast iron thicknesses equal to C, dimension for steel type 21 flanges given in IS0 7005-l.
3 Pipe dimensions affect the bore of the flange, and the external diameter and thickness of pipe which is to be joined to the flange should be
specified where appropriate. The bore sizes of integral (type 21) flanges on valves and fittings to which they form a part may be given in the
appropriate standard for the component.
4 For bolts to IS0 261 used in conjunction with IS0 PN20 and IS0 PN50 flanges :
- for sizes up to and including M45, use metric coarse series;
- for sizes M46 and above, use a constant 4 mm pitch.
26 --`,`,````,`,,`,,,,,`,`,``,,,`-`-`,,`,,`,`,,`---

IS0 700!5-2 : 1666 (El
Section 4 : Materials and pressure/temperature (p/T) ratings
4.1 Materials
Table 14 - Material applicable for each IS0 PN
Material Mechanical properties IS0 PN

Minimum Minimum
Minimum
elongation 0,2 %
tensile
after proof
Reference strength
Type Grade/Class fracture stress 2,5 6 10 16 20 25 40 50
standard
Rnl A R PO..7
min. min. min.
N/mm2 % N/mmz
IS0 185 200 2cmJ X X X X X x
Grey IS0 185 250 250 x x X X X X x x
cast iron
GI ASTM A 126 A” 145 X X
ASTM A 126 B 214 X X
IS0 1083 350-22 350 22 220 X X X X X X
IS0 2531 400-5 400 5 300 x x x X X X
Ductile IS0 1083 400-15 400 15 250 x x x X X X
cast iron IS0 1083 500-7 500 7 320 X X X X X X
DI IS0 1083 600-3 600 3 370 X x x X X X
ASTM A 395 414-18 414 18 276 X X

Malleable
cast iron IS0 5922 B 32-12 320 12 190 X x x X X
Ml IS0 5922 B 35-10 350 10 200 X X X x x
1) Grey cast iron to ASTM A 126 Class A is limited to flanges of nominal size up to and including DN 300.
--`,`,````,`,,`,,,,,`,`,``,,,`-`-`,,`,,`,`,,`---
26
IS0 700!3-2 : 1988 (El
4.2 Pressure/temperature ratings
Table 15 - Pressure/temperature ratings for grey cast iron flanges
Temperature, OC
Nomlnal Material
IS0 pressure
PN -1oto66 1 120 1 150 160 1 200 230 250 300
IS0 ASTM Maximum permissible working pressure, bar11 (gauge)
2,6 165 2,5 23 2,3 2,1 2 13 13 1,5
6 166 - 6 6 5,4 5 48 4,4 42 3,6
10 165 10 10 9 a,4 8 7,4 7 6
16 185 16 16 14,4 13,4 12,8 11,8 11,2 9,6
(<DN300) - A 126 Class A 12,l 10,3 986 fA6
--`,`,````,`,,`,,,,,`,`,``,,,`-`-`,,`,,`,`,,`---
m i (<DN300) 185 A 126 Class B 13,8 12,l 11,4 10,3 W 86
(300 <DN <6W 185 A 126 Class B 10,3 8,6 7,6 63
EOO<DN<9001 185 A 126 Class B 10,3 59 3,4
25 1852) 25 25 22,5 21 20 18,5 17,5 15
40 1852) 1 40 40 36 33,6 32 29,6 28 24
(<DN300) - A 126 Class A 27,6 23‘4 21,4 18,3 17,7
M) 1 (<DN300) 165 A 126 Class B 34,5 %‘3 25,9 23,l 20,8 17,2
(300 <DN <600) 185 A 126 Class B 20,7 17.9 16,6 15,2 14,l
(600 <DN (759) 185 A 126 Class B 20,7 13,8 10,3 69
1) 1 bar = 0,l MPa
2) IS0 PN25 and IS0 PN40 flanges manufactured In grey cast iron are limited to IS0 185 grade 250.
Table 16 - Pressure/temperature ratings for ductile cast iron flanges to IS0 2531
grade 406-5 and to IS0 1663 grades 500-7 and 600-3 1)
Temperature, OC I
Nominal pressure -1o to 12g 150 200 250 300 350
IS0 PN
Maximum permissible working pressure, bar21 (gauge)
:: 10
16 15,2
9,s 14,4
9 12,8
8 11,2
7 a,8
5,5
20 15,5 14,8 13,9 12.1 10,2 w-3
25 25 23,8 22,5 20 17,5 13,8
40 40 36 36 32 26 22
50 402 39 36 35 33 31
1) Ductile cast iron grade 600-3 flanges are limited to applications up to temperatures of 120 OC.
2) 1 bar = 0.1 MPa
36
IS0 70052 :1988 (E)
Table 17 - Pressure/temperature ratings for ductile cast iron flanges to IS0 1083
grades 350-22 and 400-15 and ASTM A 3% Class 414-18
--`,`,````,`,,`,,,,,`,`,``,,,`-`-`,,`,,`,`,,`---
I) 1 bar = 0,l MPa
Table 18 - Pressure/temperature ratings for malleable cast iron flanges to IS0 592
Nominal Temperature, OC
pressure -10 to 120 150 200 250 300 350
IS0 PN
Maximum permissible working pressure, bar’) (gauge1
6 6 58 585 5.2 4.8 4,2
10 10 9,7 9.2 8,7 8 7
16 16 15,5 14,7 13,9 12,8 11,2
26 25 24,3 23 21,8 20 17.5
40 40 38.8 36.8 34,8 32 28
I) 1 bar = 0,l MPa
31
IS0 700!!-2 : 1988 (El
Annex A
(informative)
Guidance on tolerances on dimensions

This annex lists dimensions which should be given a tolerance and also gives suggested tolerances.
NOTE - ISO/TC 5/SC 10 Working Group 6 has been instructed to prepare a table of tolerances which become mandatory by revision or by
amendment to this part of IS0 7005.
--`,`,````,`,,`,,,,,`,`,``,,,`-`-`,,`,,`,`,,`---
32
IS0 7005-2 : 1999 (E)
OOOP
008E
009E
OOVE
OOZE
OOOE
00&Z
0092
WbZ
oozz
OOOZ
0061
ootr I
ooz 1
oool ,
,
008
1
OOL .!
009 ;
009
09c ,
oob
09Z
002 ,
r
0%
9ZL
001
08
99
05
LD.
ob ect
- + I
ZE
9Z
oz
91
01
--`,`,````,`,,`,,,,,`,`,``,,,`-`-`,,`,,`,`,,`---
%
s
:
‘cB

IS0 700!%2 : 1999 (El
Annex B
(informative)
Bibliography
IS0 261 : 1973, IS0 general purpose metric screw threads - DIN 2632 : 1976, Cast iron flanges: nominal pressure 10.
General plan.
IS0 7oo!sl : - 11,Metallic flanges - Part 1: Steel flanges. DIN 2633 : 1976, Cast iron flanges; nominal pressure 16.
DIN 2630 : 1976, Cast iron flanges; nominal pressure 2,s. DIN 2534 : 1976, Cast iron flanges; nominal pressure 25,
DIN 2531 : 1976, Cast iron flanges; nominal pressure 6, DIN 2635 : 1976, Cast iron flanges: nominal pressure 40.
I) To be published.
--`,`,````,`,,`,,,,,`,`,``,,,`-`-`,,`,,`,`,,`---
34
IS0 70052 : 1988 (E)
--`,`,````,`,,`,,,,,`,`,``,,,`-`-`,,`,,`,`,,`---
UDC 621.643.412-034.13
Descriptors : metal tubes, pipe joints, cast iron products, pipe flanges, specifications, dimensions, designation, marking.
Price based on 34 pages


ISO 7005-2-1988 - Cast Iron Flanges 1

Uploaded by

Copyright:

Available Formats

ISO 7005-2-1988 - Cast Iron Flanges 1

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

ISO 7005-2-1988 - Cast Iron Flanges 1

Uploaded by

Copyright:

Available Formats

IS0

INTERNATIONAL STANDARD 7005-2

INTERNATIONAL ORGANIZATION FOR STANDARDIZATION

Partie 2: Brides en fonte

Copyright International Organization for Standardization

Section 1: General ..................................................... 1

1.1 Scope ............................................................ 1

1.2 Normative references ............................................... 1

1.3 Definitions and designations ......................................... 1

Section 2: General requirements ........................................ 3

2,l Pressure/temperature (p/T) ratings ................................... 3

2.2 Materials .......................................................... 3

2.3 Dimensions ........................................................ 3

2.4 Joint facings ....................................................... 3

2.6 Spot-facing or back-facing ........................................... 4

2.6 Marking ........................................................... 4

2.7 inspection and test ................................................. 4

2.8 Repairs ........................................................... 4

2.9 Information to be supplied by the purchaser ............................ 4

Section 3: Dimensions ................................................. 7

Section 4: Materials and pressure/temperature (p/T) ratings ............. 29

4.1 Materials .......................................................... 29

4.2 Pressure/temperature ratings ........................................ 30

0 International Organization for Standardization, 1988 l

Copyright International Organization for Standardization

Draft International Standards adopted by the technical committees are circulated to

International Standard IS0 705-2 was prepared by Technical Committee iSO/TC 5,

- Part 1: Steel flanges

- Part 2: Cast iron flanges

- Part 3 : Copper alloy and composite flanges

- Part 4: Aiuminium and aiuminium alloy flanges

Copyright International Organization for Standardization

Part 1 : Steel flanges

Part 2: Cast iron flanges

Part 4: Aluminium and aluminium alloy flanges

The materials specified in American (ANSI) standards and international Standards

Classes 125 and 150: IS0 PN20

Classes 250 and 300: IS0 PN50

any statutory requirements,

Copyright International Organization for Standardization

1.3.2 Designation of types and facings 13 - Hubbed threaded flange

14 - Hubbed socket welding flange

Copyright International Organization for Standardization

Section 2 : General requirements

2.1 Pressure/temperature (p/T) ratings 2.2.3 Bolting

NOTES 2.3.2 Dimensional details

Flanges shall be manufactured from the materials specified in

NOTE - Details of attachment for welded and threaded flanges are

2 Where there is an appropriate application standard, it is the 2.4.1 Types of facings

2.4.2 Application 2.6 Marking

a) the nominal size (DNI and the nominal pressure rating

al fiat faces, or NOTES

Where not otherwise prohibited by the applicable material stan-

Copyright International Organization for Standardization

For IS0 PN20 IS0 PN50

Figure 1 - Types of flanges

Figure 1 - Types of flanges bncludedl

Copyright International Organization for Standardization

Copyright International Organization for Standardization