PC1616/PC1832/PC1864 STANDARD INSTALLATION GUIDE

This Installation Guide provides the basic installation, wiring and programming information required to program the PowerSeries PC1616, PC1832 and PC1864 control panels. This guide shall be used in conjunction with the PowerSeries PC1616/1832/1864 Reference Manual which can be obtained from your local dealer or downloaded from the DSC web site at www.dsc.com. NOTE: All necessary information required to meet UL Listing requirements is contained in this document. Read the complete guide, then work through each step as indicated.

FEATURES OUT Of THE BOX

Qty 1 K Qty 1 K Qty 1 K Qty 1 K Qty 2 K Qty 1 K Qty 4 K Qty 16 K Qty 1 K Qty 1 K Qty 1 K Qty 1 K Cabinet PC Module Installation guide User manual Cabinet Label Cabinet Door Plug Standoffs 5.6K Resistors 2.2K Resistors 1.0K Resistors 10 Resistors Grounding Kit On-board Zones Hardwired Zones Wireless Zones Keypad Zone Support On-board PGM Outputs PGM Expansion Keypads Partitions 6

PC1616
8

PC1832
8

PC1864

16 (1xPC5108) 16

32(3xPC5108) 32

64 (7xPC5108) 32


PGM 1 - 50mA PGM 2 - 300mA 8x50mA (PC5208) 4x500 mA (PC5204) 8 2 32 + Master Codes 500 Events 16.5VAC/40VA 4Ah / 7Ah/14AHr 12V/700 mA (cont)


PGM 1 - 50mA PGM 2 - 300mA 8x50mA (PC5208) 4x500 mA (PC5204) 8 4 32 + Master Codes 500 Events 16.5VAC/40VA 4Ah / 7Ah/14AHr 12V/700 mA (cont)


PGM 1, 3, 4 - 50mA PGM 2 - 300mA 8x50mA (PC5208) 4x500 mA (PC5204) 8 8 32 + Master Codes 500 Events 16.5VAC/40VA 4Ah / 7Ah/14AHr 12V/700 mA (cont)

SPECIFICATIONS
Temp Range ....... 0C-49C (32F-120F) Humidity (Max)........................... 93%R.H. Power Supply........ 16.5VAC/40VA @60Hz Current Draw (Panel) .........110mA (nom.) Aux+ Output............11.1-12.6VDC/700mA Bell Output ..............11.1-12.6VDC/700mA

User Codes Event Buffer Transformer Required Battery Required Bell Output

COMPATIBLE DEVICES Keypads (Backward compatible with all PowerSeries keypads)

PK5500 Keypad...........................................................125mA (max.) PK5501 Keypad...........................................................125mA (max.) PK5508 LED Keypad...................................................125mA (max.) PK5516 LED Keypad...................................................125mA (max.) PC5532Z LED Keypad ................................................125mA (max.) LCD5511 Fixed Message LCD Keypad........................ 85mA (max.) LED5511Z 8-zone LED Keypad .................................100mA (max.)

Modules
T-Link TL-250/TL300 .......................................................275/350mA PC5100 2-wire Interface ............ 40mA plus devices to 170mA max. PC5132-433 Wireless Receiver .............................................125mA RF5108-433 Wireless Receiver .............................................125mA PC5108 Zone Expander ..........................................................30mA PC5204 Power Supply with 4 Programmable Outputs ............30mA PC5208 Low Current Programmable Output Module ..............50mA PC5400 Printer/DVAC Module .................................................65mA PC5401 Bi-Directional RS232 Module (Not UL Listed) ............65mA Escort5580 Telephone Interface Module ...............................130mA
Refer to the Reference Manual for additional devices.

Cabinets
PC5003C ..................................... 222x298x78mm (11.3x11.7x3.0in) PC500C ......................................... 213x235x78mm (8.4x9.25x3.0in)
Refer to the Reference Manual for alternate control cabinets

Classified in Accordance with ANSI/SIA CP-01-2000 (SIA-FAR)

2 9 0 0 7 1 0 9 R0 0 3

Hardware Installation
Begin the installation by mounting the cabinet in a dry protected area with access to unswitched AC power. Install Hardware in the sequence indicated below. Do NOT apply power until installation is complete. NOTE: All wiring entry points are designated by arrows. All circuits are classified UL power limited except for the battery leads. Minimum 1/4 (6.4mm) separation must be maintained at all points between power limited and non-power limited wiring and connections.

1. Keybus Wiring
The 4-wire KEYBUS (red, black, yellow and green) is the communication connection between the control panel and all modules. The 4 KEYBUS terminals of all modules must be connected to the 4 KEYBUS terminals of the main control panel. The following rules must be followed when wiring the Keybus: Minimum 22 AWG wire, maximum 18 AWG (2-wire twisted preferred Do NOT use shielded wire Modules can be home run, connected in series or can be Ttapped provided that the maximum wire distance from the control panel to any module does not exceed 1,000 feet (305m) No more than 3,000 feet (915m) of wire can be used in total

150 (46m) 150 (46m) 500 (152m)

CONTROL PANEL 500 (152m)

2. Zone Wiring
Zones can be wired for Normally Open, Normally Closed Contacts with Single-end-of-line (SEOL) resistors or Double End-of-Line (DEOL) resistors. Observe the following guidelines For UL Listed Installations use SEOL or DEOL only. Minimum 22 AWG wire, maximum 18 AWG Do NOT use shielded wire Wire run resistance shall not exceed 100. Refer to the chart below.

Normally Closed Loops - Do NOT use for UL Installations

Single End-of-Line Resistor Wiring

Section [001-004] Selects Zone Definition Section [013] Opt [1] Selects Normally Closed or EOL resistors Section [013] Opt [2] Selects Single EOL or Double EOL resistors.

Double End-of-Line Resistor Wiring

Zone Status Loop Resistance - 0 (shorted wire/loop) - 5600 (contact closed) - infinite (broken wire, open) - 11,200 (contact open) Loop Status Fault Secure Tamper Violated

3. Bell Wiring
These terminals supply 700mA of current at 12VDC for commercial installations and 11.1-12.6 VDC for residential installations (e.g.DSC SD-15 WULF). To comply with NFPA 72 Temporal Three Pattern requirements: Program Section [013] Opt [8] ON. The Bell output is supervised and power limited. If unused, connect a 1000 resistor across Bell+ and Bell- to prevent the panel from displaying a trouble. See [,][2].
BELL/SIREN 700mA (max.)
OBSERVE POLARITY

NOTE: Bell output is current limited by 2A PTC NOTE: Steady, Pulsed and Temporal Three Pattern alarms are supported.

Hardware Installation (Cont.)

North America Only

POWER LIMITED
1. Insert Stand off into cabinet mounting hole in the desired location. Snap-inplace. 2. Position circuit board mounting holes over standoffs. Press firmly on board to snap-in-place.
PC Board Stand Off

Cable Tie (not supplied) recommended

Cabinet

Primary:120VAC/60Hz. Secondary: 16.5VDC 40VA DSCPTD 1640U Class II Transformer NOTE: Do not connect transformer to receptacle controlled by a switch

UA503

DSC

PC1616/1832/1864
WARNING:
High Voltage. Disconnect AC Power and telephone lines before servicing

220

PC1864 Only
CON1 BAT+BATAC AC AUX+ BELL+ PGM1 PGM3 AUXBELL- RED BLK YEL GRN PGM2 PGM4 Z1 COM Z2 Z3 COM Z4 Z5 COM Z6

PC1864 PC1832 Only

Z7 COM Z8 EGND RING TIP R-1 T-1

TB-2

230 VAC/50 Hz International

CON1 BAT+BATAC AC

See Section 9 for ground wiring details

12V / 7 AHr
To EGND Terminal
BLACK RED DSC Model BD7-12 or equivalent Battery StandbyTime: 24Hrs min.

12V / 7 AHr

16.5VAC/40VA

NON-POWER LIMITED

FUSE

WARNING: Incorrect connections may result in PTC failure or improper operation.

Inspect wiring and ensure connections are correct before applying power. Incorrect connection of batteries may result in battery rupture or Fire Hazard. Do NOT allow metal objects to connect the Positive and Negative Terminals. Ensure that batteries are connected with correct polarity (Red to (+), Black to (-)). Failure to comply with this may result in battery rupture and/or Fire Hazard. All circuits are classified for UL Installations as Power Limited/Class II Power Limited except for battery leads which are not power limited. Do NOT route any wiring over circuit boards. Maintain at least 1"(25.4mm) separation. A minimum of 1/4" (6.4mm) separation must be maintained at all points between power limited wiring and all other non-power limited wiring.

IMPORTANT:
a)This equipment, Alarm Controller PC1616/1832/1864 shall be installed and used within an environment that provides the pollution degree max 2 and overvoltages category II NON-HAZARDOUS LOCATIONS, indoor only. The equipment is FIXED and PERMANENTLY connected and is designed to be installed by service persons only; [service person is defined as a person having the appropriate technical training and experience necessary to be aware of hazards to which that person may be exposed in performing a task and of measures to minimize the risks to that person or other persons.] b)The connection to the mains supply must be made as per the local authorities rules and regulations. An appropriate disconnect device must be provided as part of the building installation. Where it is not possible to rely on identification of the neutral in the AC Mains supply the disconnecting device must disconnect both poles simultaneously (line and neutral). The device shall disconnect the supply during servicing. c)The equipment enclosure must be secured to the building structure before operation. e)Internal wiring must be routed in a manner that prevents: - Excessive strain on wire and on terminal connections; - Loosening of terminal; connections; - Damage of conductor insulation f) Disposal of the used batteries shall be made according to the waste recovery and recycling regulations applicable to the intended market. g) Before servicing, DISCONNECT the telephone connection.
CON1 BAT+BAT-

UA503

REV XX

DSC

220

PC1616/1832/1864

PC-LINK

AUX+ and Keybus (Red) are Internally Connected Total current draw from Keypads, PGM Outputs and Aux circuits must not exceed 550ma

10
Internally Connected

PC1864 Only

PC1864 PC1832 Only

TB-2
AC AC AUX+ BELL+ PGM1 PGM3 AUXBELL- RED BLK YEL GRN PGM2 PGM4 Z1 COM Z2 Z3 COM Z4 Z5 COM Z6 Z7 COM Z8 EGND RING TIP R-1 T-1

WARNING:
High Voltage. Disconnect AC Power and telephone lines before servicing

See corresponding Section NumberText for wiring details.

Hardware Installation (Cont.)

4. AUX Power Wiring
The control panel can provide a maximum of 700mA of current for modules, powered detectors, relays, LEDs etc. If the total current required exceeds 700mA an additional power supply is required (e.g.,PC5200, PC5204). See list below. NOTE: Min/max operating voltages for devices, sensors and modules is 9.5VDC - 14VDC Refer to the list of Compatible Devices on the first page for the current draw of individual devices

5. PGM Wiring
PGMs switch to ground when activated by control panel. Connect the positive side of the device to be activated to the AUX+ Terminal. Connect the negative terminal to the PGM. current output is as follows PGM 1, 3, 4 .................... 50mA PGM 2 .......................... 300mA For currents levels greater than 300mA a relay is required. PGM2 can also be used for 2-wire smoke detectors. NOTE: Use SEOL resistors on Fire Zones ONLY. 2-wire Smoke Detectors Initiating Circuit
Style B (Class B), Supervised, Power Limited Compatibility Identifier ........................................................ PC18-1 DC Output Voltage..................................................... 9.8-13.8 VDC Detector Load ............................................................. 2 mA (MAX) Single-end-of-line (SEOL) Resistor ..................................... 2200 Loop Resistance............................................................24 (MAX) Standby Impedance.................................................. 1020 () Alarm Impedance ........................................................570 (MAX) Alarm Current ............................................................ 89 mA (MAX) PGM 1, LED Output with current limiting resistor and Optional Relay driver output

Compatibility ID For FSA-210B Series is: FS200

4-wire Smoke Detectors

RM-1/RM-2 POWER LOOP SUPERVISORY RELAY

6. Telephone Line Wiring

Wire the telephone connection terminals (TIP, Ring, T-1, R-1) to an RJ-31x Connector as indicated. For connection of multiple devices to the telephone line, wire in the sequence indicated. Telephone format is programmed in section [350]. Telephone Call Directions are programmed in section [351]-[376].
T-1 R-1 TIP RING

RJ-31X

7. Ground
Ground Installation
Tighten nut to break paint and make good connection to the cabinet

8. Battery
A sealed, rechargeable, lead acid battery or gel type battery is required to meet UL requirements for power standby times. NOTE: UL Residential/Commercial Burglary installations require 4Hrs Power Standby time. NOTE: UL/ULC Residential Fire & Home Care installations require 24 Hr power standby. ULC Commercial Burglary and Fire monitoring installations require 24 Hr power standby. Standby Battery Guide
Battery Charging Current: 400 mA Batt Standby Size 4Hr 24Hr ------------------------------------------------4Ahr 700mA ---7Ahr 700mA 180mA 14Ahr 700mA 470mA

9. AC Wiring
AC Wiring
UL Listed Installations Primary: 120VAC/60Hz./0.33A Secondary: 16.5VAC/40VA DSCPTD 1640 Plug-in, Class 2 Transformer. NOTE: Do not connect transformer to a receptacle controlled by a switch. (UL Listed Installations Only)

NOTE:
Replace batteries every 3-5 years. Battery capacity will deteriorate with age and number of charge/discharge cycles

TESTING & TROUBLESHOOTING

Testing:
Power up system Program options as required (See Programming Section on reverse side) Note: For advanced programming refer to the PC1616/1832/1864 Reference manual Violate, then restore zones Verify correct Reporting Codes are sent to the Central Station

Troubleshooting:
LCD5500 LCD Programmable-Message Keypad Press [][2] to view a trouble condition. The trouble light will flash and the LCD will display the first trouble condition present. Use the arrow keys to scroll through all trouble conditions present. NOTE: When additional information is available for a specific trouble condition a [] will appear on the display. Press the [] key to view the additional information LED Keypads, LCD Fixed Message Keypads Press [][2] to view a trouble condition. The trouble light will flash. Refer to the Trouble Summary chart below to determine the trouble condition(s) present.

Trouble Summary:
Light [1] Service Required - Press [1] for more information [1] Low Battery [2] Bell Circuit [3] General System Trouble [4] General system Tamper [5] Module Supervision [6] RF Jam Detected [7] PC5204 Low Battery [8] PC5204 AC Failure Light [2] AC Trouble Light [3] Telephone Line Trouble Light [4] Failure to Communicate Light [5] Zone Fault -Press [5] for more information Light [6] Zone Tamper - Press [6] for more information Light [7] Wireless Device Low Battery - Press [7] for more information Light [8] Loss of Time or Date

Trouble
Trouble [1] Service Required
[1] Low Battery

Cause
Main panel battery less than 11 VDC NOTE: This trouble condition will not clear until the battery voltage is 12.5VDC min., under load.

Troubleshooting
NOTE: If battery is new allow 1 Hr. for battery to charge. Verify voltage measured across AC terminals is 16-18 VAC. Replace transformer if required. Disconnect battery wire leads Verify battery charging voltage measured across battery leads = 13.70 - 13.80 VDC. Connect battery, remove AC power Verify measured voltage across battery terminals is 12.5VDC min. Disconnect Bell-/Bell+ wire leads, measure resistance of wire leads. Open circuit indicates break in wiring or defective siren/bell Jumper Bell+, Bell- with 1K resistor (Brown, Black, Red) Verify trouble clears If Output#1 is unused: Ensure that terminals O1, AUX are jumpered with 1K resistor (Brown, Black, Red) If Output #1 is used: Disconnect wire leads from O1, AUX terminals, measure the resistance of the wire leads Open circuit indicates a break in the wiring Verify voltage measured across AC input terminals is 16-18VAC. Disconnect all connections to PC5204 AUX terminal. Verify AUX voltage is 13.70 - 13.80 VDC.

Press [1] to determine specific trouble

[2] Bell Circuit

Bell+, Bell-...Open Circuit

[3] General System Trouble PC5204 Output#1 Open Circuit

PC5204 AUX

Printer connected to PC5400 offline T-Link Network Fault present T-Link Receiver Trouble present T-Link Interface Trouble present [4] General System Tamper Tamper input on module(s) open circuit Wireless Receiver - excessive noise detected [5] Module Supervision Panel does not communicate with module(s) on KEYBUS Keypad assigned to incorrect slot.

Verify printer operation (out of paper, paper jam etc.) Refer to the T-Link TL250/350 Installation Manual for details.

Short tamper terminal to COM terminal on unused modules connected to KEYBUS (PC5100, PC5108, PC5200, PC5204, PC5208, PC5320, PC5400, PC5700). Check for external 433MHZ signal sources To disable RF Jam: enable Option [7] in program section [804] subsection [90]. Modules are immediately enrolled and supervised when detected on the KEYBUS. If a module has been removed, or if the slot assignment of a keypad has been changed, module supervision must be reset. View the event buffer (via DLS or LCD5500 keypad) to identify the specific module(s) in trouble To reset module supervision: Enter Program Section [902]. Press [#] (wait 1 minute for panel to scan KEYBUS). Enter Program Section [903] to identify modules connected to KEYBUS. Check for external 433MHZ signal sources To disable RF Jam: enable Option [7] in program section [804] subsection [90]. See [1] Low Battery above

[6] RF Jam Detected

Wireless Receiver - excessive noise detected. PC5204 battery less than 11.5VDC NOTE: This trouble condition will not clear until the battery voltage is 12.5VDC min., under load.

[7] PC5204 Low Battery

[8] PC5204 AC Failure

No AC at PC5204 AC inputs

Verify voltage measured across AC terminals is 16-18VAC. Replace transformer if required.

Trouble
Trouble [2] AC Failure

Cause
No AC at panel AC input terminals

Troubleshooting
Verify voltage measured across AC terminals is 16-18VAC. Replace transformer if required.

Trouble [3] Telephone Line Trouble

Phone Line Voltage at TIP, RING on main panel less than 3VDC Measure the voltage across TIP and RING on the panel: No phone off-hook 50VDC (approx) Any phone off-hook 5VDC (approx) Wire incoming line directly to TIP and RING. If trouble clears, check wiring or the RJ-31 phone jack.

Trouble [4] Failure to Communicate

Panel fails to communicate one or more events to central station Connect a headset to TIP and RING of the control panel. Monitor for the following conditions: Continuous dial tone Reverse TIP and RING Recorded operator message comes on Verify correct phone number is programmed Dial the number programmed using a regular telephone to determine if a [9] must be dialed or if 800 service is blocked. Panel does not respond to handshakes. Verify the format programmed is supported by the central station. Panel transmits data multiple times without receiving a handshake Verify that the account number and reporting codes are correctly programmed. NOTE: Contact ID and Pulse formats Program a HEX [A] to transmit a digit [0] SIA format Program a digit [0] to transmit a digit [0]

Trouble [5] Zone Fault

Press [5] to determine specific zones with a fault trouble

Open circuit is present on one or more fire zones on the main panel or zone expander Ensure fire zones have a 5.6K resistor (Green, Blue, Red) connected. Remove the wire leads from Z and COM terminals and measure the resistance of the wire leads. An open circuit indicates a break in the wiring or resistor not connected. Connect a 5.6K resistor (Green, Blue, Red) across the Z and COM terminals. Verify the trouble condition clears. Ensure the correct 2.2K end-of-line resistor is connected (Red, Red, Red). Remove the wire leads from PGM2 and AUX+ terminals and measure the resistance of the wire leads. An open circuit indicates a break in the wiring or no resistor connected. Connect a 2.2K resistor (Red, Red, Red) across the PGM2 and AUX+ terminals. Verify the trouble condition clears.

An open circuit is present on PGM2 being used as a 2-wire smoke detector input

Trouble
Trouble [5] Zone Fault (Cont.)

Cause
One or more wireless devices have not checked in within the programmed time

Troubleshooting
If the trouble occurs immediately, a conflict with a hard wired zone exists: The zone being used is already assigned to a PC5108 zone expander The zone being used is assigned as a keypad zone Perform a Module Placement Test Program Section [904] and verify the wireless device is in a good location. If bad test results occur, test the wireless device in another location If the wireless device now tests good, the original mounting location is bad If the wireless device continues to give bad test results replace the wireless device Remove the wire leads from Z and COM terminals and measure the resistance of the wire leads. A short circuit indicates a short in the wiring. Connect a 5.6K resistor (Green, Blue, Red) across the Z and COM terminals. Verify the trouble condition clears.

A short circuit is present on one or more zones with double end-of-line resistors enabled

Trouble [6] Zone Tamper

Press [6] to determine specific zones with a tamper trouble

A tamper condition is present on one or more wireless devices An open circuit is present on one or more zones with double end-of-line resistors enabled Perform a Module Placement Test Section [904] Violate, then restore the tamper: If no test result then replace wireless device Remove the wire leads from Z and COM terminals. Measure the resistance of the wire leads. Open circuit indicates a break in the wiring. Connect a 5.6K resistor (Green, Blue, Red) across the Z and COM terminals. Verify the trouble condition clears.

Trouble [7] Wireless Device Low Battery

1st press Wireless Zones 2nd press Handheld Keypads 3rd press Wireless Keys

Press [7] to toggle through specific devices with low battery trouble
Replace battery NOTE: Replacing batteries will cause a tamper. Replacing cover will restore the tamper causing the associated reporting codes to be sent to the Central Station.

One or more wireless devices has a low battery NOTE: The event will not be logged to the event buffer until the wireless device low battery delay time expires Program Section [377] Opt 9

Trouble [8] Loss of Clock/Date

The main panel internal clock is not set To program the time and date: Enter [][6][Master Code] then Press [1] or Press function key programmed with definition #26 Enter the time and date (in military) using the following format: HH:MM MM/DD/YY Example. For 6:00 pm, June 29, 2005 Enter: [18] [00] [06] [29] [05]

IMPORTANT! Ensure you have the following information available before contacting Customer Support - Control Panel Type and Version, (e.g., PC1864 v4.1) NOTE: Version number can be accessed by entering [][Installer Code][900] on any system keypad. This information is also located on a sticker on the Printed Circuit Board. - List of modules connected to Control Panel, (e.g., PC5400, PC5204 etc.)

PROGRAMMING
How to Program:
DSC recommends filling in the Programming Worksheet with the required programming information before programming the system. This will reduce the time required to program and will help eliminate errors. To enter Installer Programming press [*][8][5555]. The Program light will FLASH (or in the case of the programmable LCD keypad the display will change to Enter Section). An error tone indicates the installer code entered is not correct. Press [#] to clear any key presses and try again. The Armed and Ready lights indicate programming status: Armed Light ON Ready Light ON Ready Light FLASHING NOTE: Panel waiting for 3-digit section number Panel waiting for data to be entered Panel waiting for HEX data to be entered

the required data. The Ready light will turn OFF and the Armed light will turn ON. At any time the [#] can be pressed to exit any program section. All changes made up to that point will be saved. HEX (or hexadecimal) digits are sometimes required. To enter a HEX digit, press the [*] key to begin HEX programming. The Ready light will FLASH. Refer to the chart below and press the number corresponding to the HEX digit required. The Ready light will continue to FLASH. Press [*] again to return to normal decimal programming. The Ready light will turn ON.
HEX [A] HEX [B] HEX [C] HEX [D] HEX [E] HEX [F] [*] [1] [*] [*] [2] [*] [*] [3] [*] [*] [4] [*] [*] [5] [*] [*] [6] [*]

You cannot enter installer programming while the system is armed or in alarm.

How to Exit Installer Programming: To exit installer programming, press the [#] key when the panel is waiting for a 3-digit section number (the Armed light is ON).

Programming Toggle Options: Enter the 3-digit programming section number. The Armed light will turn OFF and The Ready light will turn ON. The keypad will display which toggle options are ON or OFF according to the chart below:

Viewing Programming
LED and LCD5501Z Keypads
Any programming section can be viewed from an LED or LCD5501Z keypad. When a programming section is entered, the keypad will immediately display the first digit of information programmed in that section. The keypad displays the information using a binary format, according to the following chart:
See Hex data entry instructions

Keypad Type
LED Fixed-Message LCD Programmable-Message LCD

Option ON
Zone Light ON Indicator # ON # Displayed

Option OFF
Zone Light OFF Indicator # OFF Dash [-] Displayed

To toggle an option ON or OFF, press the corresponding number on the keypad. The display will change accordingly. When all the toggle options are configured correctly, press the [#] key to exit the program section. The Ready light will turn OFF and the Armed light will turn ON. If the panel is a local system, press [#] to skip this step. In addition to the standard digits 0-9, HEX digits can also be programmed if required. HEX [A] HEX [B] HEX [C] HEX [D] HEX [E] Not Supported Simulated [*] key Simulated [#] key Dial tone search Two second pause Press Press Press Press [*][2][*] [*][3][*] [*][4][*] [*][5][*]

NOTE: NOTE:

Press any of the Emergency keys (Fire, Auxiliary or Panic) to advance to the next digit. When all the digits in a section have been viewed, the panel will exit the section: the Ready light will turn OFF, and the Armed light will turn ON, waiting for the next 3-digit programming section number to be entered. Press the [#] key to exit the section

LCD Keypad
When a programming section is entered, the keypad will immediately display all the information programmed in that section. Use the arrow keys (< >) to scroll through the data being displayed. To exit the section, scroll past the end of the data displayed, or press the [#] key.

DLS Programming
Hardware Setup - Local (PC-Link) Connect a RS-232 to PC-Link Cable between the Computer with DLS Software installed and the alarm panel to be programmed.

Programming Decimal and Hexadecimal (HEX) Data:

Enter the 3-digit programming section number. The Armed light will turn OFF and The Ready light will turn ON. Enter the data written in the boxes.

[401] First Downloading Option Code

The 1st toggle option in this section is used to enabled/disable Downloading. Configure the options as required and press [#] to exit. Opt 2 I__I Default  ON OFF Description User can enable DLS Window User can NOT enable DLS Window

For sections that require multiple 2 or 3 digit numbers, the keypad will double-beep after each 2 or 3 digit entry and move to the next item in the list. After the last digit in the section is entered, the keypad will beep rapidly 5 times and exit the program section. The Ready light will turn OFF and the Armed light will turn ON. For sections that do not require data for every box (such as phone numbers) press the [#] key to exit the program section after entering all

[402] Downloading Computer Phone Number (32-digits)

I

KEYPAD FUNCTION KEY DEFINITIONS 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 Null Key (Key not used) Partition 1 Select Partition 2 Select Stay Arm Away Arm [,][9] No entry arm [,][4] Chime On/Off [,][6][----][4]System Test [,][1] Bypass Mode [,][2] Trouble display [,][3] Alarm memory [,][5] User programming [,][6] User functions Command output 1 [,71] Command output 1 [,72] Sensor Reset 15 General voice prompted help 16 [,][0] Quick Exit 17 [,][0] Activate Stay/Away 18 Identified voice prompted help 19 Command output 3 [,73] 20 Not used 21 Command output 4 [,74] 22 Active camera monitor selection 23 Bypass Recall 24 Bypass Group Recall 25 Not Used 26 Time Programming 27 Partition 3 Select 28 Partition 4 Select 29 Partition 5 Select 30 Partition 6 Select 31 Partition 7 Select 32 Partition 8 Select

DII___II___II___II___II___II___II___II___II___II___II___II___II___II___II___I

I___II___II___II___II___II___II___II___II___II___II___II___II___II___II___II___I

[403] Downloading Access Code Enter 4 or 6-digit code

This code identifies the downloading computer to the panel. The downloading access code prevents unauthorized access to the panel. This code must match the code programmed in the downloading file before the panel will allow remote or local DLS connection. Enter a new downloading access code to disable downloading.

Default XXXXXX

I___II___II___II___II___II___I

[404] Panel Identification Code

This code identifies the panel to the downloading computer. See section [403]

Enter 6 decimal places Default XXXXXX I___II___II___II___II___II___I

[001]-[004] Zone Definitions

Enter the number corresponding to the zone definitions required.The keypad will beep rapidly 3 times and move to the next step. If an invalid number is entered the keypad will revert to the default setting (option [1]).

[499][Installer Code][499] Initiate PC-Link Enter [499][Installer Code][499] Special Installer Functions
Enter section# for the following features [900] [902] [903] [904] Panel Version ([,][8][Installer Code][900]) Module Supervision Reset ([,][8][Installer Code][902]) Module Supervision Field ([,][8][Installer Code][903]) Wireless Module Placement Test ([,][8][Installer Code][904]) Enter section#, Installer Code section# for the following features [990] INSTALLER CODE [990] [991] INSTALLER CODE [991] [993] INSTALLER CODE [993] [995] INSTALLER CODE [995] [996] INSTALLER CODE [996] [997] INSTALLER CODE [997] [999] INSTALLER CODE [999] Installer Lockout Enable Installer Lockout Disable Restore Alt.Comm. Factory Defaults Restore Escort 5580 Factory Defaults Restore PC5132 Factory Defaults Restore PC5400 Factory Defaults Restore Panel Factory Defaults

Press [#] to exit the section.

[001] Zone 1-16 Definitions ALL Models Def 01 I__II__I Zone 1 03 I__II__I Zone 2 03 I__II__I Zone 3 03 I__II__I Zone 4 04 I__II__I Zone 5 04 I__II__I Zone 6 04 I__II__I Zone 7 04 I__II__I Zone 8 Def 00 I__II__I Zone 9 00 I__II__I Zone 10 00 I__II__I Zone 11 00 I__II__I Zone 12 00 I__II__I Zone 13 00 I__II__I Zone 14 00 I__II__I Zone 15 00 I__II__I Zone 16 00 Null Zone (not used) 01 Delay 1 02 Delay 2 03 Instant 04 Interior 05 Interior, Stay/Away 06 Delay, Stay/Away 07 Delayed 24-hr Fire (Hard-wired) 08 Standard 24-hr Fire (Hard-wired) 09 24-hr Supervisory 10 24-hr Supervisory Bu 11 24-hr Burglary 12 24-hr Holdup 13 24-hr Gas 14 24-hr Heat 15 24-hr Medical 16 24-hr Panic 17 24-hr Emergency 18 24-hr Sprinkler 19 24-hr Water 20 24-hr Freeze 21 24-hr Latching Tamper 22 Momentary Keyswitch arm 23 Maintained Keyswitch Arm 24 Future Use 25 Interior Delay 26 25-hr non-alarm 27 Delayed 24-hr Water Flow 28 Instant 24-hr Water Flow 29 Auto-verified Fire 30 Fire Supervisory 31 Day zone 32 24-hr Bell/Buzzer 33 Push to set 34 Final Door set 35 Instant Stay, Away 36 24-hr Non latching Tamper 37 Night Zone 87 Delayed 24-hr Fire (Wireless) 88 24-hr Fire (Wireless)

[002] Zone 17-32 Definitions PC1864 & PC1832 Def 00 I__II__I Zone 17 00 I__II__I Zone 18 00 I__II__I Zone 19 00 I__II__I Zone 20 00 I__II__I Zone 21 00 I__II__I Zone 22 00 I__II__I Zone 23 00 I__II__I Zone 24 Def 00 I__II__I Zone 25 00 I__II__I Zone 26 00 I__II__I Zone 27 00 I__II__I Zone 28 00 I__II__I Zone 29 00 I__II__I Zone 30 00 I__II__I Zone 31 00 I__II__I Zone 32

[000] Keypad Programming

Note: This programming must be done at each keypad
[0] [1] [2] [3] [4] [5] Slot Address (0-8) for partition, 1-8 for slot Function key Assignment (00-32) Function key Assignment (00-32) Function key Assignment (00-32) Function key Assignment (00-32) Function key Assignment (00-32)

[003] Zone 33-48 Definitions PC1864 Only Def 00 I__II__I Zone 33 00 I__II__I Zone 34 00 I__II__I Zone 35 00 I__II__I Zone 36 00 I__II__I Zone 37 00 I__II__I Zone 38 00 I__II__I Zone 39 00 I__II__I Zone 40 Def 00 I__II__I Zone 41 00 I__II__I Zone 42 00 I__II__I Zone 43 00 I__II__I Zone 44 00 I__II__I Zone 45 00 I__II__I Zone 46 00 I__II__I Zone 47 00 I__II__I Zone 48

Slot Address ICON LED Defaults Full Message Defaults Keypad 1 Keypad 2 Keypad 3 Keypad 4 Keypad 5 Keypad 6 Keypad 7 Keypad 8 11

Key 1 03

Key 2 04

Key 3 06

Key 4 14

Key 5 16

[004] Zone 49-64 Definitions PC1864 Only Def Def 00 I__II__I Zone 57 00 I__II__I Zone 58 00 I__II__I Zone 59 00 I__II__I Zone 60 00 I__II__I Zone 61 00 I__II__I Zone 62 00 I__II__I Zone 63 00 I__II__I Zone 64

18

03

04

06

14

16

00 I__II__I Zone 49 00 I__II__I Zone 50 00 I__II__I Zone 51 00 I__II__I Zone 52 00 I__II__I Zone 53 00 I__II__I Zone 54 00 I__II__I Zone 55 00 I__II__I Zone 56

[005] System Times

This section programs the entry and exit delays for the control panel. After entering section [005] press [1] to select partition 1. Enter the 3-digit delay time for Delay 1 type zones, Delay 2 type zones followed by the exit delay time. Press [#] to exit the sub-menu and return to regular programming. NOTE: For SIA FAR Installations, the Exit Delay must be within the range of 045-255 seconds (Default 60 seconds). If the Exit Delay is silent (Section 14, Option 6 or Stay Function Key Arming) the exit delay must be twice the programmed value but must not exceed 255 seconds (i.e., 090-255 seconds). NOTE: For UL Installations, the Entry Delay plus the Communications Delay must not exceed 60 seconds. NOTE: Exit Time Restart shall be disabled when the panel is used in combination with T-Link TL250/TL300.
[005] [01] Partition 1 Entry/Exit Times Def 030 I___II___II___I *045 I___II___II___I **120 I___II___II___I Enter 3 digits [[001]-[255] Entry Delay 1 Entry Delay 2 Exit Delay 1 Valid entries: [030] to [255] Valid entries: [030] to [255] Valid entries: [060] to [255]

[013] First System Option Code

The first two toggle options in this section are used to determine what type of EOL resistors are being used, toggle option [1] to determine if normally-closed or EOL resistors are being used and option [2] to determine if single or double EOL resistors are being used. Configure the options as required and press [#] to exit.
Opt Default Description

I__I 

ON OFF ON  OFF ON  OFF

Normally Closed loops End-of-line Resistors Double End-of-Line Resistors Single End-of-Line Resistors Temporal Three Fire Signal Standard Pulsed Fire Signal.

I__I

I__I

[015] Third System Option Code

This section is used to determine if the Panic keys on the keypads will be audible or silent (toggle option [2]) and if phone line supervision is enabled or disabled (toggle option [7]). Configure the options as required and press [#] to exit.
Opt 2 I__I  7 I__I  Default ON OFF ON OFF Description [P] Key Audible (Bell/Beeps) loops [P] Key Silent TLM Enabled TLM Disabled

*Entry Delay 2 Default is 030 for SIA CP-01 Installations **Exit Delay 1 Default is 060 for SIA CP-01 Installations

[006] Installer Code Enter a new 6-digit Installer Code

Default 555555 I___II___II___II___II___II___I

[018] Cross Zone/Police Code

NOTE: The panel uses the cross zoning attribute for Burglary Verification. This feature requires two or more trips on a zone(s) specified as cross zones within a specified time before starting an alarm sequence (See Section[101] Option 3, page 33 of the Reference Manual).
Opt Default Description

[007] Master Code Enter a new 6-digit Master Code

Default 123456 I___II___II___II___II___II___I

[008] Maintenance Code Enter a new 6-digit Maintenance Code

Default AAAAAA I___II___II___II___II___II___I

I__I

ON OFF

Cross Zoning Enabled Police Code is Enabled

[009-010] PGM Programming PGMs 3&4 apply to PC1864 only

[009] Def 19 10 01 01 I___II___I I___II___I I___II___I I___II___I Main Board PGM Output Programming Enter 2 digits [[01]-[32] PGM 1 PGM 2 PGM 3 PGM 4 Section [009] Section [009] Section [010] ...... PC1864 Only Section [010] ...... PC1864 Only
17 Away Armed Status 18 Stay Armed Status 19 Command Output#1 (,71) 20 Command Output#1 (,72) 21 Command Output#1 (,73) 22 Command Output#1 (,74) 23 24-hr Silent Input 24 24-hr Audible Alarm 25 Delayed Fire & Burglary Output 26 Battery Test Output 27 Police Code Output 28 Holdup Output 29 Zone Follower Inverted Output 30Partition Status Alarm Memory Output 31 Alternate Communications 32 Open After Alarm (Abort Code)

[165] Maximum Dialing Attempts to each Phone Number This section programs the number of Dialing Attempts. Enter a 3-digit. For UL Listed Installations 5-10 Dialing attempts are required.
[165] Def 005 I___II___II___I Maximum Dialing Attempts to each Phone Enter 3 digits [[001]-[005] Valid entries: [001] to [005]

01 Fire & Burglary Output 02 Not Used 03 Sensor Reset (,72) 04 2-Wire Smoke (PGM2 Only) 05 Armed Status) 06 Ready to Arm 07 Keypad buzzer follow mode 08 Courtesy Pulse 09 System Trouble output (with Trouble Options) 10 System Event (with Event Options) 11 System Tamper (All Sources) 12 TLM and Alarm 13 Kiss-off Output 14 Ground Start Pulse 15 Remote Operation 16 Future Use

[301] First Telephone Number (32-digits)

Program the central station phone number or CAA for T-LINK. In addition to the standard digits [0] - [9], Hex digits may also be required (Refer to the Programming Decimal and Hexadecimal (HEX) Data at the beginning of this section).

DII___II___II___II___II___II___II___II___II___II___II___II___II___II___II___I

I___II___II___II___II___II___II___II___II___II___II___II___II___II___II___II___

[304] Call Waiting Cancel String (6 Digits) Program Unused digits with Hex F
Default DB70EF [Hex] I___II___II___II___II___II___I

[310]-[311] Partition Identifier Codes Enter a 6 digit Maintenance Code

[310 System Acct. Code [311] Partition 1 Acct. Code I___II___II___II___II___II___I

[380] First Communicator Option Codes

Opt 1 I__I Default  ON OFF Description Communications Enabled Communications Disabled Restorals on Bell Time-out Restorals Follow Zones Pulse Dialing DTMF Dialing 3rd Telephone Number Enabled 3rd Telephone Number Disabled Delinquency Follows Zone Activity (Hours) Delinquency Follows Arming (Days)

I___II___II___II___I 2 I__I  3 I__I  5 I__I  8 I__I  ON OFF ON OFF ON OFF ON OFF

[350] Communicator Format Options

This section determines the communication format used for central station reporting. From the chart listed below program the 2-digit number for the desired format for the first and second telephone number
Def 04 04 I___II___I I___II___I Enter 2 digits From Chart Below NOTE: 3rd Phone Number follows the format of the 1st Phone Number
07 10BPS, 1400 Hz Handshake 08 10BPS, 2300 Hz Handshake 09 Private Line 10 Scantronics 4-8-1 Fast Slo 12 Robofon 13 CESA 200

01 20BPS, 1400 Hz Handshake 02 20BPS, 2300 Hz Handshake 03 DTMF Contact ID 04 SIA FSK 05 Pager 06 Residential Dial

[381] Second Communicator Option Codes

The 3rd toggle option in this section is used to enable/disable automatic SIA reporting. The 5th toggle option is used to enable/disable automatic Contact ID reporting. Configure the options as required and press [#] to exit. NOTE:If the automatic SIA or automatic Contact ID reporting formats are not used, reporting codes must be programmed. To program reporting codes refer to the PowerSeries PC1616/1832/1864 Reference Manual which can be downloaded from the DSC web site at www.dsc.com
Opt Default I__I  5 I__I  ON OFF ON Description SIA Sends Programmed Reporting Codes SIA Sends Automatic Reporting Codes Contact ID Uses Programmed Reporting Codes Contact ID Uses Automatic Reporting Codes

[367] Opening/Closing Call Direction Options

The first toggle option in this section is used to enable/disable opening/ closing reporting for partition 1. To enable opening/closing reporting turn option [1] ON. Configure the options as required and press [#] to exit
.

Opt

Default

Description

I__I 

ON OFF ON  OFF ON  OFF

1st Telephone Number Disabled 2nd Telephone Number

I__I

3 Disabled Alternate Communicator Disabled

I__I

OFF

[377] Communication Variables

NOTE: For UL Installations, the Entry Delay plus the Communications Delay must not exceed 60 seconds.
Def 003 I___II___II___I 003 I___II___II___I 003 I___II___II___I 000 I___II___II___I 030 I___II___II___I 010 I___II___II___I 030 I___II___II___I 030 I___II___II___I 007 I___II___II___I 030 I___II___II___I 000 I___II___II___I Enter 3 digits as indicated below Swinger Shutdown (Alarms and Rest. Swinger Shutdown (Tamper and Rest. Swinger Shutdown (Maint. and Rest. Communication Delay AC Failure Comm Delay TLM Trouble Delay Test Transmission Cycle (land line) Not Used Zone low Battery Transmission Delay Delinquency Transmission Cycle Communications Cancelled Window (001-014 Transmissions) (001-014 Transmissions, 000=disabled) (001-014 Transmissions, 000=disabled) (000-255 seconds) (001-255 minutes) No. of checks reqd (003255) (001-255 days/minutes)

[382] Third Communicator Option Codes

The 4th toggle option in this section is used to enable/disable Call Waiting Cancel. Configure the options as required and press [#] to exit. NOTE:A Call Waiting Cancel on a Non Call Waiting line will prevent successful connection to the central station.
Opt 4 I__I  5 I__I  Default ON OFF ON OFF Description Call Waiting Cancel Enabled Call Waiting Cancel Disabled T-Link Interface Enabled T-Link Interface Disabled

[701] First International Options Codes

(000-255 days) (000-255 days/hours) (000-255 minutes)

Option 7 in this section Selects Battery Charge Options. Select ON for 7 Ahr and 14 Ahr batteries (700 mA charge rate) Select OFF for Standard 4 Ahr batteries (400 mA charge rate)
Opt Default Description

I__I 

ON OFF

High Current Battery Charge (700mA) Standard Battery Charge Rate (400mA)

NOTE: Option 1 is defaulted to 001 for CP-01 Installations Option 4 is defaulted to 030 for CP-01 Installations Option 11 is defaulted to 005 for CP-01 Installations

LISTING REQUIREMENTS
UL Listed Commercial and Residential Installations
The installation requirements listed below must be met for the following grades of service. Grade AA Central Station and Police Connect (Standard or Encrypted Line Security Service) The installation must use T-Link module which communicates over LAN/WAN to the Sur-Gard MLR-IP receiver or the TL200/250 which communicates over LAN/ WAN/Internet to the SG System III receiver. Polling time must be 90 seconds. Compromise detection time must be 6 minutes. Grade A Local The installation must have a bell which is UL Listed for mercantile local alarms (AMSECO MBL10B with model AB-12 bell housing). The digital communicator must be enabled. The control panel must be in the attack-resistant enclosure (DSC Model CMC-1 or PC4050CAR). Grade B Central Station and Police Connect The installation must have a bell which is UL Listed for mercantile local alarms (AMSECO MBL10B with model AB-12 bell housing). The digital communicator must be enabled. The control panel must be in the attack resistant enclosure (DSC Model CMC-1 or PC4050CAR). Grade C Central Station The digital communicator must be enabled. The control panel must be in the attack resistant enclosure (DSC Model CMC-1 or PC4050CAR). All Commercial Installations The Entry Delay must not exceed 120 seconds The Exit Delay must not exceed 120 seconds. The minimum Bell Time-out is 15 minutes. Residential Fire & Burglary Installations The Entry Delay must not exceed 45 seconds The Exit Delay must not exceed 60 seconds. The minimum Bell Time-out is 4 minutes. Home Health Care Signaling Equipment There must be at least two keypads, one of either the LCD5500Z/LCD5520Z or LCD5501Z and one of the following models, PC5508Z, PC5516Z or PC5532Z. Each system shall be programmed to activate an audible Trouble signal within 90 seconds upon loss of microprocessor memory. The minimum Bell Time-out is 5 minutes. Programming The notes in the programming sections describing the system configurations for UL Listed installations must be implemented. Control of the Protected Premises In order to have a UL Certificated system the protected area is to be under the responsibility of one ownership and management (i.e., one business under one name). This may be a group of buildings attached or unattached with different addresses but under the responsibility of someone having mutual interest. The person of mutual interest is not the alarm-installing company. Bell Location The alarm sounding device (bell) must be located where it can be heard by the person or persons responsible for maintaining the security system during the daily arming cycle. Protection of the Control Unit The local control and the local power supply must be protected in one of the following ways: The control unit and audible alarm device must be in a protected area which is armed 24 hours a day. Each partition must arm the area protecting the control unit and the audible alarm device power supply. This may require duplicate protection armed by each partition. Access to this protected area, without causing an alarm, will require that all partitions be disarmed. In all cases described above, the protected area for the control unit must be programmed as not-bypassable. Casual Users The installer should caution the user(s) not to give system information to casual users (e.g. codes, bypass methods, etc. to baby-sitters or service people). Only the One-Time Use codes should be given to casual users. User Information The installer should advise the users and note in the Users Manual: Service organization name and telephone number The programmed exit time The programmed entry time Test system weekly Two-Wire Smoke Detector Compatibility (if available) Maximum loop resistance: 24 Ohms Operating Voltage Range: 9.8 - 13.8 VDC Maximum Alarm Current: 89 mA Compatibility Identifier: PC18-1 See Section 5 PGM Wiring for compatible 2-wire smoke detectors.

SIA FAR Installations

Minimum requirement system for SIA-FAR Installations: 1 PC1616/PC1832/PC1864 Control panel 2 Local annunciation devices The local annunciation devices may be any combination of the following keypads, as long as there is at least one LCD keypad in the installation (Model LCD5500Z or PK5500). LCD5500Z LCD5501Z PK5500 PK5508 PKP-LCD PKP-ICN PK5501 PK5516 The following optional subassembly modules also bear the SIA FAR classification and may be used if desired: PC5108 Zone Expander Module Compatible initiating devices: Bravo200 series, 300 series, 400 series, 500 series, 600 series, AC-100, Encore300 series, Force200 series, 210 series, MN240. PC5208 Low Current PGM Output Module The following optional accessory modules also bear the SIA FAR classification and may be used if desired. PC5204 Auxiliary Power Supply with PGM output ports Escort5580/Escort5580TC, PC5400 Printer Module

Caution
For SIA FAR installations, only use modules / devices that are listed on this page. Fire Alarm Verification feature (Auto Verified Fire zone) is not supported on 2wire smoke detectors zones. This feature may be enabled for 4-wire smoke detectors only. Call Waiting Cancel (Section 382 Option 4) feature on a non-Call Waiting line will prevent successful communication to the central station. All smoke detectors on the system must be tested annually by conducting the Installer Walk Test prior to exiting the walk test mode, a sensor reset must be conducted on the system, [,][7][2] to reset all latching 4-wire smoke detectors. Please refer to the smoke detector installation instructions on how to correctly test the detectors.

Notes
Programming at installation may be subordinate to other UL requirements for the intended application. Cross zones have the ability to individually protect the intended area (e.g., motion detectors, which overlap). Cross zoning is not recommended for line security Installations nor is it to be implemented on exit / entry zones. There is a communication delay of 30 seconds in this control panel. It can be removed, or it can be increased up to 45 seconds at the option of the end user by consulting with the Installer. Do not duplicate any reporting codes. This applies for all communication formats other than SIA sending automatic programmed reporting codes. The control unit must be installed with a local sounding device and an offpremise transmission for SIA communication format. For ULC Listed Fire Monitoring Installations & module requirements, please refer to the ULC Installation Information sheet, part# 29002157. Use a CSA/cUL transformer, hardwired. All tamper circuits may be connected to the same zone. Use ULC-LA for AC Power indication.

PC1616/PC1832/PC1864 Installer Programming Quick Reference Chart SIA False Alarm Reduction
SIA Feature Programming Section
Exit Time [005], 3rd entry Progress Annunciation/ Disable - for Silent Exit [014], Option 6 ON

Comments
Access to Entry and Exit delays for each partition and Bell Time Out for the system

Range/Default
For Full or auto arming: Range:45- 255 seconds Default: 60 sec. Individual keypads may be disabled Default: All Enabled Default: Enabled If no exit after full arm Default: Enabled Default: Enabled

Requirement
Required (programmable) Allowed

Enables audible exit beeps from the keypad for the duration of exit delay

Exit Time Restart

[018], Option 7 ON Auto Stay Arm on Unvacated Premises [001]-[004] Zone type 05, 06 Exit Time and Progress Annunciation/Disable or Remote Arming [005] and [014] bit 6 Entry delay(s) [005], 1st and 2nd entry Abort Window for Non-Fire zones [101]-[164] bit 7 ON Abort Window - for Non-Fire zones [377], 4th entry Abort Annunciation [382], Option 3 ON Cancel Annunciation [328], 8th entry Duress Feature [*][5] Master Code 33rd and 34th entries Cross Zoning [018] Option 6 [101]-[164] bit 9 OFF Cross Zone Timer [176] Swinger Shutdown for Alarms [377] 1st entry Swinger Shutdown Disable [101] - [164] bit 6 ON Fire Alarm Verification Zone type [29] Call Waiting Cancel Dial String [304], [382], Option 4 OFF

Enables the exit delay restart feature Function Key: Stay Arming. All Stay/Away type zones (05, 06) will be automatically bypassed System Times and Audible Exit beeps can be disabled when using the Key fob to arm away the system

Required Required

Allowed

Access to Entry and Exit delays for each partition and Bell Time Out for the system Note: Combined Entry delay and Communications Delay (Abort Window) shall not exceed 60s Access to zone attributes, i.e, swinger shutdown, transmission delay and cross zone. Individual zones attribute bit 7 (Transmission delay) is by default ON Access to the programmable delay before communicating alarms Note: Combined Entry delay and Communications Delay (Abort Window) shall not exceed 60s Enables the Communication Cancelled" message display on all keypads

Range: 30 sec. to 4 min. Default: 30 sees May be disabled by zone or zone type Default: Enabled Range: 15 - 45 sec. Default: 30 sees Annunciate that no alarm was transmitted Default: Enabled Annunciate that a Cancel was transmitted Default: Enabled No 1+ derivative of another user code. No duplicates with other user codes Default: disabled Programming required Default: Disabled May program Range: 001-255 sec./min. Default: 60 secs For all non-fire zones shut down at 1 or 2 trips Default: 1 Trip For non-police response zones Default: Enabled 70 seconds reset and confirmation time Default: disabled Dependant on user phone line Default: disabled

Required (programmable) Required

Required (programmable) Required

Access to the reporting code for Alarm Cancelled

Required

Do not derive code from an existing Master/User code (e.g., Master code is 1234, the duress code should not be 1233 or 1235)

Allowed

This option enables Cross Zoning for entire system. Individual zones can be enabled for Cross zoning via Zone attribute bit 9 in sections [101] - [164] Access to the programmable Cross Zone timer

Required

Allowed

Access to the swinger shutdown limit for zone alarms

Required (programmable) Allowed

Access to zone attributes, i.e., swinger shutdown, transmission delay and cross zone. Individual zones attribute bit 6 (Swinger shutdown enabled) is by default ON Auto Verified Fire, use only with 4 wire type detectors that can be reset by the panel 4wire smoke detector powered from AUX = and PGM1 - PGM4 (type 03, Sensor reset) Access to the dialing sequence used to disable call waiting

Required

Required

Testing
System Test: [*][6] Master Code, Option 4 Installer Walk Test Mode: [901 Alarm Communications During Walk Test [382] Option 2: The system activates all keypad sounders, bells or sirens for 2 seconds and all keypad lights turn on.

Refer to the User Manual (part no. 29007165).

This mode is used to test each zone on the system for proper functionality. Enables Communication of zone alarms while installer Walk Test is active.

Walk Test End and Begin Reporting Codes [348], 1st and 2nd Entries

Access to the reporting codes for Walk Test Begin and Walk Test End.

Note to Installers
This warning contains vital information. As the only individual in contact with system users, it is your responsibility to bring each item in this warning to the attention of the users of this system.

Limited Warranty
Digital Security Controls warrants the original purchaser that for a period of twelve months from the date of purchase, the product shall be free of defects in materials and workmanship under normal use. During the warranty period, Digital Security Controls shall, at its option, repair or replace any defective product upon return of the product to its factory, at no charge for labour and materials. Any replacement and/or repaired parts are warranted for the remainder of the original warranty or ninety (90) days, whichever is longer. The original purchaser must promptly notify Digital Security Controls in writing that there is defect in material or workmanship, such written notice to be received in all events prior to expiration of the warranty period. There is absolutely no warranty on software and all software products are sold as a user license under the terms of the software license agreement included with the product. The Customer assumes all responsibility for the proper selection, installation, operation and maintenance of any products purchased from DSC. Custom products are only warranted to the extent that they do not function upon delivery. In such cases, DSC can replace or credit at its option.

System Fail ur es
This system has been carefully designed to be as effective as possible. There are circumstances, however, involving fire, burglary, or other types of emergencies where it may not provide protection. Any alarm system of any type may be compromised deliberately or may fail to operate as expected for a variety of reasons. Some but not all of these reasons may be: n Inadequate Installation A security system must be installed properly in order to provide adequate protection. Every installation should be evaluated by a security professional to ensure that all access points and areas are covered. Locks and latches on windows and doors must be secure and operate as intended. Windows, doors, walls, ceilings and other building materials must be of sufficient strength and construction to provide the level of protection expected. A reevaluation must be done during and after any construction activity. An evaluation by the fire and/or police department is highly recommended if this service is available. n Criminal Knowledge This system contains security features which were known to be effective at the time of manufacture. It is possible for persons with criminal intent to develop techniques which reduce the effectiveness of these features. It is important that a security system be reviewed periodically to ensure that its features remain effective and that it be updated or replaced if it is found that it does not provide the protection expected. n Access by Intruders Intruders may enter through an unprotected access point, circumvent a sensing device, evade detection by moving through an area of insufficient coverage, disconnect a warning device, or interfere with or prevent the proper operation of the system. n Power Failure Control units, intrusion detectors, smoke detectors and many other security devices require an adequate power supply for proper operation. If a device operates from batteries, it is possible for the batteries to fail. Even if the batteries have not failed, they must be charged, in good condition and installed correctly. If a device operates only by AC power, any interruption, however brief, will render that device inoperative while it does not have power. Power interruptions of any length are often accompanied by voltage fluctuations which may damage electronic equipment such as a security system. After a power interruption has occurred, immediately conduct a complete system test to ensure that the system operates as intended. n Failure of Replaceable Batteries This systems wireless transmitters have been designed to provide several years of battery life under normal conditions. The expected battery life is a function of the device environment, usage and type. Ambient conditions such as high humidity, high or low temperatures, or large temperature fluctuations may reduce the expected battery life. While each transmitting device has a low battery monitor which identifies when the batteries need to be replaced, this monitor may fail to operate as expected. Regular testing and maintenance will keep the system in good operating condition. n Compromise of Radio Frequency (Wireless) Devices Signals may not reach the receiver under all circumstances which could include metal objects placed on or near the radio path or deliberate jamming or other inadvertent radio signal interference. n System Users A user may not be able to operate a panic or emergency switch possibly due to permanent or temporary physical disability, inability to reach the device in time, or unfamiliarity with the correct operation. It is important that all system users be trained in the correct operation of the alarm system and that they know how to respond when the system indicates an alarm. n Smoke Detectors Smoke detectors that are a part of this system may not properly alert occupants of a fire for a number of reasons, some of which follow. The smoke detectors may have been improperly installed or positioned. Smoke may not be able to reach the smoke detectors, such as when the fire is in a chimney, walls or roofs, or on the other side of closed doors. Smoke detectors may not detect smoke from fires on another level of the residence or building. Every fire is different in the amount of smoke produced and the rate of burning. Smoke detectors cannot sense all types of fires equally well. Smoke detectors may not provide timely warning of fires caused by carelessness or safety hazards such as smoking in bed, violent explosions, escaping gas, improper storage of flammable materials, overloaded electrical circuits, children playing with matches or arson. Even if the smoke detector operates as intended, there may be circumstances when there is insufficient warning to allow all occupants to escape in time to avoid injury or death. n Motion Detectors Motion detectors can only detect motion within the designated areas as shown in their respective installation instructions. They cannot discriminate between intruders and intended occupants. Motion detectors do not provide volumetric area protection. They have multiple beams of detection and motion can only be detected in unobstructed areas covered by these beams. They cannot detect motion which occurs behind walls, ceilings, floor, closed doors, glass partitions, glass doors or windows. Any type of tampering whether intentional or unintentional such as masking, painting, or spraying of any material on the lenses, mirrors, windows or any other part of the detection system will impair its proper operation. Passive infrared motion detectors operate by sensing changes in temperature. However their effectiveness can be reduced when the ambient temperature rises near or above body temperature or if there are intentional or unintentional sources of heat in or near the detection area. Some of these heat sources could be heaters, radiators, stoves, barbecues, fireplaces, sunlight, steam vents, lighting and so on. n Warning Devices Warning devices such as sirens, bells, horns, or strobes may not warn people or waken someone sleeping if there is an intervening wall or door. If warning devices are located on a different level of the residence or premise, then it is less likely that the occupants will be alerted or awakened. Audible warning devices may be interfered with by other noise sources such as stereos, radios, televisions, air conditioners or other appliances, or passing traffic. Audible warning devices, however loud, may not be heard by a hearing-impaired person. n Telephone Lines If telephone lines are used to transmit alarms, they may be out of service or busy for certain periods of time. Also an intruder may cut the telephone line or defeat its operation by more sophisticated means which may be difficult to detect. n Insufficient Time There may be circumstances when the system will operate as intended, yet the occupants will not be protected from the emergency due to their inability to respond to the warnings in a timely manner. If the system is monitored, the response may not occur in time to protect the occupants or their belongings. n Component Failure Although every effort has been made to make this system as reliable as possible, the system may fail to function as intended due to the failure of a component. n Inadequate Testing Most problems that would prevent an alarm system from operating as intended can be found by regular testing and maintenance. The complete system should be tested weekly and immediately after a break-in, an attempted break-in, a fire, a storm, an earthquake, an accident, or any kind of construction activity inside or outside the premises. The testing should include all sensing devices, keypads, consoles, alarm indicating devices and any other operational devices that are part of the system. n Security and Insurance Regardless of its capabilities, an alarm system is not a substitute for property or life insurance. An alarm system also is not a substitute for property owners, renters, or other occupants to act prudently to prevent or minimize the harmful effects of an emergency situation.

International Warranty
The warranty for international customers is the same as for any customer within Canada and the United States, with the exception that Digital Security Controls shall not be responsible for any customs fees, taxes, or VAT that may be due.

Warranty Procedure
To obtain service under this warranty, please return the item(s) in question to the point of purchase. All authorized distributors and dealers have a warranty program. Anyone returning goods to Digital Security Controls must first obtain an authorization number. Digital Security Controls will not accept any shipment whatsoever for which prior authorization has not been obtained.

Conditions to Void Warranty

This warranty applies only to defects in parts and workmanship relating to normal use. It does not cover: damage incurred in shipping or handling; damage caused by disaster such as fire, flood, wind, earthquake or lightning; damage due to causes beyond the control of Digital Security Controls such as excessive voltage, mechanical shock or water damage; damage caused by unauthorized attachment, alterations, modifications or foreign objects; damage caused by peripherals (unless such peripherals were supplied by Digital Security Controls Ltd.); defects caused by failure to provide a suitable installation environment for the products; damage caused by use of the products for purposes other than those for which it was designed; damage from improper maintenance; damage arising out of any other abuse, mishandling or improper application of the products.

Items Not Covered by Warranty

In addition to the items which void the Warranty, the following items shall not be covered by Warranty: (i) freight cost to the repair centre; (ii) products which are not identified with DSC's product label and lot number or serial number; (iii) products disassembled or repaired in such a manner as to adversely affect performance or prevent adequate inspection or testing to verify any warranty claim. Access cards or tags returned for replacement under warranty will be credited or replaced at DSC's option. Products not covered by this warranty, or otherwise out of warranty due to age, misuse, or damage shall be evaluated, and a repair estimate shall be provided. No repair work will be performed until a valid purchase order is received from the Customer and a Return Merchandise Authorization number (RMA) is issued by DSC's Customer Service. Digital Security Controls Ltd.s liability for failure to repair the product under this warranty after a reasonable number of attempts will be limited to a replacement of the product, as the exclusive remedy for breach of warranty. Under no circumstances shall Digital Security Controls be liable for any special, incidental, or consequential damages based upon breach of warranty, breach of contract, negligence, strict liability, or any other legal theory. Such damages include, but are not limited to, loss of profits, loss of the product or any associated equipment, cost of capital, cost of substitute or replacement equipment, facilities or services, down time, purchasers time, the claims of third parties, including customers, and injury to property. The laws of some jurisdictions limit or do not allow the disclaimer of consequential damages. If the laws of such a jurisdiction apply to any claim by or against DSC, the limitations and disclaimers contained here shall be to the greatest extent permitted by law. Some states do not allow the exclusion or limitation of incidental or consequential damages, so that the above may not apply to you.

Disclaimer of Warranties
This warranty contains the entire warranty and shall be in lieu of any and all other warranties, whether expressed or implied (including all implied warranties of merchantability or fitness for a particular purpose) and of all other obligations or liabilities on the part of Digital Security Controls. Digital Security Controls neither assumes responsibility for, nor authorizes any other person purporting to act on its behalf to modify or to change this warranty, nor to assume for it any other warranty or liability concerning this product. This disclaimer of warranties and limited warranty are governed by the laws of the province of Ontario, Canada. WARNING: Digital Security Controls recommends that the entire system be completely tested on a regular basis. However, despite frequent testing, and due to, but not limited to, criminal tampering or electrical disruption, it is possible for this product to fail to perform as expected.

Out of Warranty Repairs

Digital Security Controls will at its option repair or replace out-of-warranty products which are returned to its factory according to the following conditions. Anyone returning goods to Digital Security Controls must first obtain an authorization number. Digital Security Controls will not accept any shipment whatsoever for which prior authorization has not been obtained. Products which Digital Security Controls determines to be repairable will be repaired and returned. A set fee which Digital Security Controls has predetermined and which may be revised from time to time, will be charged for each unit repaired. Products which Digital Security Controls determines not to be repairable will be replaced by the nearest equivalent product available at that time. The current market price of the replacement product will be charged for each replacement unit.

FCC COMPLIANCE STATEMENT

CAUTION: Changes or modifications not expressly approved by Digital Security Controls could void your authority to use this equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be deter-mined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Re-orient the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/television technician for help. The user may find the following booklet prepared by the FCC useful: "How to Identify and Resolve Radio/Television Interference Problems". This booklet is available from the U.S. Government Printing Office, Washington D.C. 20402, Stock # 004-000-00345-4.

Equipment Maintenance Facility

If trouble is experienced with this equipment PC1616, PC1832, PC1864 for repair or warranty information, please contact the facility indicated below. If the equipment is causing harm to the telephone network, the Telephone Company may request that you disconnect the equipment until the problem is solved. This equipment is of a type that is not intended to be repaired by the end user. DSC c/o APL Logistics, 757 Douglas Hill Rd., Lithia Springs, GA 30122

Additional Information
Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information. Alarm dialling equipment must be able to seize the telephone line and place a call in an emergency situation. It must be able to do this even if other equipment (telephone, answering system, computer modem, etc.) already has the telephone line in use. To do so, alarm dialling equipment must be connected to a properly installed RJ-31X jack that is electrically in series with and ahead of all other equipment attached to the same telephone line. Proper installation is depicted in the figure below. If you have any questions concerning these instructions, you should consult your telephone company or a qualified installer about installing the RJ-31X jack and alarm dialling equipment for you.

IMPORTANT INFORMATION
This equipment complies with Part 68 of the FCC Rules. On the side of this equipment is a label that contains, among other information, the FCC registration number and ringer equivalence number (REN) for this equipment. If requested, this number must be provided to the Telephone Company. PC1864 Product Identifier US: F53AL01BPC1864 PC1832 Product Identifier US: F53AL01BPC1832 PC1616 Product Identifier US: F53AL01BPC1614 REN: 0.1B USOC Jack: RJ-31X

Customer Premises Equipment and Wiring

Network Service Provider's Facilities RJ-31X Jack Alarm Dialing Equipment Telephone Line

Computer
Unused RJ-11 Jack

Telephone
Network Demarcation Point

Telephone Connection Requirements

A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details.

Telephone
Answering System

Fax Machine

Unused RJ-11 Jack

Telephone

INDUSTRY CANADA STATEMENT

NOTICE: This Equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is confirmed by the registration number. The abbreviation, IC, before the registration number signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not imply that that Industry Canada approved the equipment NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is 0.1. The REN assigned to each terminal equipment provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all devices does not exceed five. PC1864 Registration number . . . . . . . . . . . . . . . . . . . . . . . . . .IC: 160A-PC1864 PC1832 Registration number . . . . . . . . . . . . . . . . . . . . . . . . . .IC: 160A-PC1832 PC1616 Registration number . . . . . . . . . . . . . . . . . . . . . . . . . .IC: 160A-PC1614

Ringer Equivalence Number (REN)

The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local Telephone Company. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format. US: AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label.

Incidence of Harm
If this equipment PC1864/PC1832/PC1616 causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice is not practical, the Telephone Company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.

Changes in Telephone Company Equipment or Facilities

The Telephone Company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the Telephone Company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service.

2006, Digital Security Controls Printed in Canada