See discussions, stats, and author profiles for this publication at: https://www.researchgate.

net/publication/281424508

Towards improving shell and beam finite elements

Conference Paper · August 2015

CITATIONS READS

0 352

3 authors, including:

Phill-Seung Lee Kyungho Yoon

Korea Advanced Institute of Science and Technology Korea Institute of Science and Technology
118 PUBLICATIONS 3,253 CITATIONS 40 PUBLICATIONS 679 CITATIONS

SEE PROFILE SEE PROFILE

All content following this page was uploaded by Kyungho Yoon on 02 September 2015.

The user has requested enhancement of the downloaded file.

 Towards improving shell and beam finite elements

*Phill-Seung Lee1), Youngyu Lee 2), Kyungho Yoon 3)

1)
Department of Mechanical Engineering, KAIST, Daejeon 305-701, Korea
2)
Agency for Defense Development, Daejeon 305-600, Korea
3)
Institute of Advanced Machines and Design, Seoul National University, Seoul 151-
742, Korea
1)
[email protected]

ABSTRACT

We introduce the MITC3+ shell element (Lee et. al, 2014) and the continuum
mechanics based beam elements (Yoon and Lee, 2014) recently developed. The
elements can be employed for linear and nonlinear analyses of general shell and beam
structures with improved performance. The 3-node MITC3+ shell element passes all
the basic numerical tests and shows excellent convergence behaviors even in distorted
meshes. Indeed, its performance is as good as that of the 4-node MITC4 shell element,
which has been widely used in commercial FE software. The continuum mechanics
based beam elements can model complicated 3D beam geometries and material
compositions by employing cross-sectional discretization, and provides an ability to
accurately predict fully coupled 3D behaviors of stretching, bending, shearing, twisting
and warping. Its superb modeling capabilities can encompass complicated mechanical
characteristics of bio- and nano-structures. In this presentation, we briefly introduce
their formulations and demonstrate their performance through numerical examples.

1. INTRODUCTION

Finite element method has been widely used for analysis of shell and beam
structures. For a long time, significant efforts have been made to develop more
effective and robust structural finite elements.

In this presentation, we share the results of our previous studies on the development of
shell and beam finite elements by introducing the MITC3+ shell element (Lee et. al,
2014, Jeon et. al, 2014, Lee et. al, 2015, Jeon et. al, 2015) and the continuum
mechanics based beam elements (Yoon et. al, 2012, Yoon and Lee, 2014) recently

1)
Associate Professor
2)
Senior Researcher
3)
Post-Doctoral Researcher
developed. The 3-node MITC3+ shell element passes patch tests, zero energy mode
tests, isotropic tests, and shows excellent convergence behavior in linear and nonlinear
analyses. Its performance is as good as that of the 4-node MITC4 shell element, which
has been widely adopted in most commercial FE software. The continuum mechanics
based beam element allows cross-sectional discretization, leading to superb modeling
capabilities considering fully coupled 3D behaviors of stretching, bending, shearing,
twisting and warping.

In the following sections, the basic formulations of the MITC3 shell element and the
continuum mechanics based beam are reviewed and their performances are briefly
presented.

2. MITC3+ SHELL ELEMENT

The geometry interpolation of the MITC3+ shell element, shown in Fig. 1, is given by
 3
 t 4   1   
x (r , s, t ) = ∑ hi (r , s ) xi + ∑ ai f i (r , s ) Vni with a4Vn4 = (a1Vn1 + a2Vn2 + a3Vn3 ) , (1)
i =1 2 i =1 3
in which f i (r , s ) are two-dimensional interpolation functions that include the cubic
bubble function f 4 corresponding to the internal node 4
1 1 1
f1 = h1 − f 4 , f 2 = h2 − f 4 , f 3 = h3 − f 4 , f 4 = 27rs (1 − r − s ) . (2)
3 3 3

Figure 1. Geometry interpolations of the MITC3+ shell element.

From Eq. (1), we obtain the displacement interpolation

 3
 t 4  
u (r , s, t ) = ∑ hi (r , s )u i + ∑ ai f i (r , s ) (−V2iα i + V1i β i ) , (3)
i =1 2 i =1
in which α 4 and β 4 are the rotation degrees of freedom at the bubble node.
The assumed transverse shear strain field is used for the MITC3+ shell element, see
Fig. 2 for the tying positions used.
2 1 1 1
eˆrt = (ert( B ) − est( B ) ) + (ert( C ) + est( C ) ) + cˆ(3s − 1) ,
3 2 3 3
2 ( A) 1 ( A) 1 ( C ) 1
eˆst = (est − ert ) + (ert + est(C ) ) + cˆ(1 − 3r ) . (4)
3 2 3 3

Figure 2. Tying positions (A)-(F) for the assumed transverse shear strain field of the
shell element.

Figure 3. Hemispherical shell problem ( R = 10 , t = 0.04 , p = 1 , E = 6.825 × 10 7 and ν = 0.3 )

and distorted mesh patterns (a) for N = 4 and, (b) for N = 8 .

We consider the hemispherical shell problem shown in Figure 3 [Macneal and Harder,
1985]. Due to symmetry, only a one-quarter model is considered. The symmetry
condition is imposed: u z = β = 0 along BC, u x = β = 0 along AD. Both uniform and

distorted meshes are considered. Figure 4 shows the convergence curves of the
displacement u z at Point A for the MITC3 and MITC3+ shell elements. Unlike the
MITC4 shell element, the MITC3+ shell element presents good results even in the
distorted mesh cases.

Figure 4. Convergence curves for the hemispherical shell problem.

3. CONTINUUM MECHANICS BASED BEAM

The geometry interpolation of the q -node continuum mechanics based beam finite
element for sub-beam m is given by
 (m) q
 q k q 
x = ∑ hk (r ) x k + ∑ hk (r ) y k V y + ∑ hk (r ) z k( m ) V zk
(m)

k =1 k =1 k =1 (5)
p p
with y k( m ) = ∑ h j ( s, t ) y kj ( m ) , z k( m ) = ∑ h j ( s, t ) z kj ( m ) , (6)
j =1 j =1

where y k(m ) and z k(m ) denote the material position of the sub-beam element m in the
cross-sectional Cartesian coordinate system on cross-sectional plane k . Eq. (5)
indicates that the material position on the cross-sectional plane is interpolated by cross-
sectional nodes, see Figure 5.

From the interpolation of geometry in Eq. (5), the interpolation of displacements

corresponding to the sub-beam m is derived

{ } { }
 q
 q   q   q 
u ( m ) = ∑ hk (r )u k + ∑ hk (r ) y k( m ) θ k × V yk + ∑ hk (r ) z k( m ) θ k × V zk + ∑ hk (r ) f k( m ) ( s, t ) Vrk , (7)
k =1 k =1 k =1 k =1
 
in which u k and θ k are the displacement and rotation vectors, respectively, in the
global Cartesian coordinate system at beam node k , u k = u k v k w k

{ } T
and

{ }
θ k = θ xk θ yk θ zk , and f k(m ) and tα k are the warping function and the corresponding
T

warping degree of freedom at beam node k .

Figure 5. The concept of the continuum mechanics based beam finite element with
sectional discretization

The example in Figure 6 illustrates single turn of the double helix DNA geometries and
its continuum mechanics based beam model. Four turns model of length 28.56 nm is
discretized by 32 beam elements. The linear elastic material with Young’s modulus
E = 50000 pN / nm 2 and zero Poisson’s ratio is used. Table 1 displays the mechanical
properties of proposed DNA continuum model compared with experimental values.
Excellent modeling capability and potential of an efficient analysis tool for DNA
nanostructures are well illustrated.

Figure 6. Double helical DNA problem: (a) DNA structure, (b) beam model. (unit: nm )

Table 1. Comparison of mechanical properties.

Experimental value
Present beam model
(Castro et. al 2011)
Stretching modulus 1100 pN 1050 pN
Bending modulus 230 pNnm 2 211.4 pNnm 2
Twisting modulus 460 pNnm 2 488.6 pNnm 2

4. CONCLUSIONS

In this presentation, we introduced the MITC3+ shell element and the continuum
mechanics based beam elements recently developed. Their formulations were briefly
reviewed and their performances were presented through representative numerical
examples. Both structural finite elements have promising accuracy and modeling
capabilities. We believe that both elements will be widely utilized to enhance the
predictive ability of finite element models in various engineering practices including
design of classical structures and applications of nano- and bio-structures.
 ACKNOWLEDGEMENTS

This work was supported by the Human Resources Development Program (No.
20134030200300) of the Korea Institute of Energy Technology Evaluation and Planning
(KETEP) funded by the Ministry of Trade, Industry and Energy, and the Basic Science
Research Program through the National Research Foundation of Korea (NRF) funded
by the Ministry of Education, Science and Technology (No. 2014R1A1A1A05007219).

REFERENCES

Castro, C.E., Kilchherr, F., Kim, D.N., Shiao, E.L., Wauer, T., Wortmann, P., Bathe, M.,
Dietz, H. (2011), “A primer to scaffloded DNA origami”, Nature Methods, 8, 221-229.
Jeon, H.M., Lee, Y., Lee, P.S., Bathe, K.J. (2015), “The MITC3+ shell element in
geometric nonlinear analysis”. Computers and Structures, 146, 91-104.
Jeon, H.M., Lee, P.S., Bathe, K.J. (2014), “The MITC3 shell finite element enriched by
interpolation covers”. Computers and Structures, 134, 128–142.
Lee, P.S., Bathe, K.J. (2004), “Development of MITC isotropic triangular shell finite
elements”. Computers and Structures, 82, 945-962.
Lee, Y., Jeon, H.M., Lee, P.S., Bathe, K.J. (2015), “The modal behavior of the MITC3+
triangular shell element”. Computers and Structures, 153, 148-164.
Lee, Y., Lee, P.S. and Bathe, K.J. (2014), “The MITC3+ shell finite element and its
performance”, Computers and Structures, 138, 12-23.
Macneal, R.H., Harder, R.L. (1985), “A proposed standard set of problems to test finite
element accuracy”, Finite Element Analysis and Design, 1, 3-20.
Yoon K., Lee P.S. (2014), “Modeling the warping displacement fields for
discontinuously varying arbitrary cross-section beams”. Computers and Structures,
131, 56-69.
Yoon, K. and Lee, P.S. (2014), “Nonlinear performance of continuum mechanics based
beam elements focusing on large twisting behaviors”, Computer Methods in Applied
Mechanics and Engineering, 281, 106-130.
Yoon K, Lee Y, Lee PS. (2012) A continuum mechanics based 3-D beam finite element
with warping displacements and its modeling capabilities. Structural Engineering and
Mechanics, 43(4), 411-437.

View publication stats