Scribd
Upload
29 views6 pages

LCA Lab Report 2

Uploaded by

mukarrumoffical
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
29 views6 pages

LCA Lab Report 2

Uploaded by

mukarrumoffical
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 6

Department of Electrical Engineering

Faculty Member: Engr. Ahsan Azhar Dated: 26/09/2024

Lab Engineer: Engr. Muhammad Ali Khalid

Semester: 1st Section: 16-D

EE-111: Linear Circuit Analysis

Lab 2: Introduction to PSpice

PLO4/CLO5 PLO5/CLO6 PLO8/CLO7 PLO9/CLO8

Name Reg. No Viva /Quiz / Analysis Modern Ethics and Individual


Lab of data Tool Usage Safety and
Performance in Lab Teamwork
Report 5 marks 5 marks
5 marks
5 marks 5 marks

Hassan 509821

Saif Ullah 511676


Farooqi
Syed 500861
Mukarrum
Ali
Table of Contents
Introduction……………………………………………………………………………………………3

Objectives……………………………………………………………………………………………….3

Equipment………………………………………………………………………………………………3

Theoretical Background…………………………………………………………………………4

Conclusion………………………………………………………………………………………………5
Introduction
In this lab session, we learned to utilize the Pspice
software, on how to use it to make simple circuits
and find the value of voltage, current and power
through any component. We learned where each of
the circuit components are in the software and how
to insert them and set up the circuit.

Objectives
The objectives of this lab were to: -

• Learn the use of the Pspice software.


• Learn how to make a simple circuit using software.
• To find out how to insert the resistance.
• To find out how to insert the power source.
• To find out how to insert the wires.
• To find out how to insert the grounding.
• To find out how to save and run the simulation.
• To find out how to check the voltage, current and power
through a component.

Equipment
The following equipment was required during the lab: -
• Mouse
• Computer
• Keyboard
3
• Pspice software
• Capture Lite Edition

Theoretical Background
We made our circuits on Capture Lite Edition. First, we click File->
New --> Project and create a blank document. Now we start
placing the circuit elements. To place wire press shift+W and left
click. To place ground, press shift+G, choose 0 source and press
ok. For placing resistor, click place--> parts ---> analog. Now type
R in symbol and press ok. This will allow us to place resistor. To
place dc voltage source, click place --> part. Choose source from
library and write Vdc under part. This will allow us to place voltage
source. Now to run the circuit, click Pspice--> New Simulation
Profile, name it and press ok. Now choose Bias point from the
dropdown menu of Analysis type. Bias point shows us the current,
voltage and power through components in a circuit but does not
show us any sort of graph. Now press V, I and W on the top of the
page to view current, voltage and power through the components.

Task 1

In the first task, we were simply asked


to make a circuit using wires, 10V dc power source, two resistors and a
ground.
4
Task 2

This task is similar to the previous


one but we just had to add another resistance(R3) in parallel to R2,
reducing the total resistance.

Task 3

This task increased the total number


of resistors in both series and parallel along with adding another power
source.

Conclusion
By the end of the lab, we became accustomed to the use of Pspice to
make simple circuits and to find power, voltages and currents. This
5
helped us to make even more complex circuits as can be seen in task 3.

You might also like