Manual
Manual
One S3 Manual
1
When building a PC, it’s important to use hardware you’re comfortable working with. From Antec, the
team behind dozens of award-winning enclosures since 1986, comes the One / One S / One S3, the
gaming case that gives you everything you need right out of the box at an attractive price. This enclosure
is stocked with features you value – USB 3.0, ample cooling and tool-less 5.25” & 3.5” drive bays – so
that you can put your PC together with ease and get to the fun stuff. If you’re looking for high quality
gaming essentials at an affordable cost, then this enclosure is the One for you.
The One / One S / One S3 does not include a power supply. Make sure you choose a power supply that is
compatible with your computer components and has a long enough power harness to reach your
motherboard and peripheral devices. We recommend our High Current Gamer or Earthwatts power
supplies for the latest ATX specification compliance, broad compatibility, and power savings capability.
At Antec, we continually refine and improve our products to ensure the highest quality. As such, your
new chassis may differ slightly from the description in this manual due to improvements applied for the
optimal building experience. As of the date of publication, all features, descriptions, and illustrations in
this manual are correct.
Disclaimer
This manual is intended only as a guide for Antec’s computer
enclosures. For more comprehensive instructions on installing the
motherboard and peripherals, please refer to the manuals that
come with those components.
Section 1: Introduction
1.1 Getting to Know Your Chassis ............................................................................5
1.2 Chassis Specifications.........................................................................................6
1.3 Included Screws .................................................................................................7
One
One S / One S3
One S:
- 2 x USB 2.0 ports
Put the case upright on a flat, stable surface so that the rear panel (power supply and expansion
slots) is facing you.
Before you connect a cable, ensure that both connectors are correctly aligned and oriented.
Do not sit on your chassis. Although it is constructed of heavy-duty steel and internally
reinforced, it is not designed to support the weight of an adult, and may buckle.
Do not use your fingernails to separate edges or lift the sides of the chassis, as paint chipping or
injury may occur.
Exercise caution and control when handling chassis interiors. We strongly recommend taking
the appropriate time and care when working inside the chassis. Avoid hurried or careless
motions.
You need to remove the front bezel in order to access the air filters and conduct maintenance.
1. Grip the bezel by the bottom and pull forward. The bezel will pop free of the chassis.
Before proceeding, check the manual for your CPU cooler to find out if there are steps you must do
before installing the motherboard.
Make sure you have the correct I/O panel for your motherboard. If the panel provided with the chassis
isn’t suitable, please contact your motherboard manufacturer for the correct I/O panel.
This case comes with 5 preinstalled motherboard standoffs. These are positioned for Standard ATX
motherboards but can be relocated to accommodate other form factors.
1. Align the motherboard with the standoff holes on the motherboard tray and remember or mark
which holes are lined up.
2. Install standoffs as needed and put the motherboard in.
3. Screw your motherboard into the standoffs with the provided motherboard mounting screws.
10
The following instructs how to install the Antec KUHLER H2O liquid CPU cooler (620 / 920). For any other
CPU coolers, please consult your manufacturer’s installation guide.
Caution:
Check your motherboard’s CPU socket to ensure its compatibility with the KUHLER H2O. The KUHLER
H2O 620 / 920 is compatible with the following CPU sockets:
*Your unit may not contain the LGA 2011 mounting bracket. To receive this bracket, please contact
Antec customer support (information is listed at end of manual).
**Be sure to install the KUHLER H2O with the end of the tubes positioned at the bottom of the radiator.
1. Remove the rear fan by unscrewing the fan from the back of the chassis.
2. Preparing the KUHLER H2O backplate is specific to your CPU socket. Please refer to the KUHLER
H2O installation guide, available at
http://www.antec.com/Believe_it/product.php?id=Mjc2OCYxNw== (KUHLER H2O 620) or
http://www.antec.com/Believe_it/product.php?id=NzA0MzcwJjE3 (KUHLER H2O 920) for more
information.
3. Prepare the retention ring according to the CPU socket you’re using.
4. Complete installation according to the KUHLER H2O instructions.
1. With the case upright, place the power supply in the case and align the rear of the unit with the
mounting holes.
2. Attach the power supply to the case with the screws provided.
11
1. Remove the side panels and front bezel as directed in Section 2.2.
2. Remove the drive bay cover by pressing out on the two small tabs on either side of the cover,
then pushing the cover into the front of the bezel.
3. Replace the front bezel on the front of the chassis.
4. Slide your 5.25” drive through the front of the chassis until it lines up flush with the front bezel.
You will feel the drive lock into position.
5. If you need more clearance on the inside of the chassis for your drive, pull the drive bay tab on
the inside of the chassis toward you and push the drive in further.
Note: You can optionally secure your drive with screws for extra stability (D in Section 1.3)
Slide you drive until it locks. Pull on the tab to adjust drive bay clearance.
Press down on the drive cover tabs. Remove the drive bay cover.
12
There are two 2.5” drive mounting locations in the One / One S / One S3: at the base of the drive cage
and a dedicated mount in the middle of the drive cage.
Note: The 2.5” drives install from the right side of the case.
Align your drive’s holes with the drive bay holes Secure your drive with the provided 2.5” screws.
when sliding it in.
13
The One / One S / One S3 includes 5 pairs of 3.5” drive rails. You will need 1 pair per 3.5” drive.
Pinch the ends of the drive rails and then slide your drive into the 3.5”
bay until it locks into position.
14
One / One S3: The One and One S3 come with two front panel USB 3.0 ports
and includes an internal motherboard connector. Connect these in the same
way you would a standard front panel with an internal header connector.
One S: The One S comes with two front panel USB 2.0 ports. Connect these Align the connector properly to
in the same way you would a standard front panel with an internal header prevent damage to your
motherboard.
connector.
1 2
Pin Signal Names Pin Signal Names
1 USB Power 1 2 USB Power 2
3 Negative Signal 1 4 Negative Signal 2
5 Positive Signal 1 6 Positive Signal 2
7 Ground 1 8 Ground 2
9 Key (No Connection) 10 Empty Pin
9 10
USB 2.0 pin assignments
There is an Intel® standard 10-pin AC’97 connector and an Intel® 10-pin HDA (High Definition Audio)
connector linked to the front panel of the chassis.
You can connect either the AC’97 or the HDA connector, depending on your motherboard. Locate the
internal audio connectors from your motherboard or sound card and connect the corresponding audio
cable. Consult your motherboard or sound card manual for the pin-out positions. Even if your system
supports both standards, only use one connector.
16
Note: Polarity (positive and negative) does not matter for switches.
17
There may come a time when you need to reconfigure the pin-out of a motherboard header connector.
Examples could be for your USB header, audio input header, or some other front panel connector such
as the Power Button connector.
Before performing any work, please refer to your motherboard user’s manual or your motherboard
manufacturer's website to confirm the pin-out needed for your connector. We strongly recommend
making a notated drawing before beginning work so that you can recover if your work gets disturbed.
Determine which wires you need to remove in order to rewire your plug to match the USB pin-outs on
your motherboard (refer to your motherboard user’s manual). Working on one connector at a time, use
a very small flathead screwdriver or similar tool to lift up on the black tab located beside the gold posts
(squares). This will allow you to easily slide out the pins from the USB plug.
Working carefully so as not to damage the wires, connectors, or pins, slowly remove the pin from the
connector. Repeat these steps for each wire you need to change.
Working carefully so as not to damage the wires, connectors or pins, slowly insert the pin into the
correct slot of the connector then snap closed the black tab that was lifted in step 1. Repeat these steps
for each wire you need to change.
18
20
One S / One S3: The One S / One S3 includes mounts for up to four more fans. These mounts are as
follows:
- 1 x front intake 120 mm mount
- 1 x side 120 mm mount
- 1 x bottom 120/140 mm mount
- 1 x rear 120 mm mount
21
At the base of the case, there is a fan mount that can fit either a 120 mm or 140 mm fan for
additional air intake.
The One / One S / One S3 features a PSU air intake filter that can be removed and cleaned.
1. Pull the filter out toward you using the tab at the back
of the chassis.
Pull the filter toward you using the tab outside the
chassis.
22
Technical Support
US &Canada
1-800-22ANTEC
[email protected]
Europe
+49-40 226139-42
[email protected]
www.antec.com
23