Panel Cutout and Dimensions

GS-UV-C-2 / GS-UV-C-3 MAX

10mm
2 1 3
Operating Instructions

Panel cutout

71mm
36mm

GS-UV-C-2 GS-UV-C-3

59 mm
29mm
Side Lock
PANEL

GASKET

Features :
Ÿ Range: 0 to 99 Minutes/Seconds
Ÿ Relay Output for UV-C. CONTROLLER
Ÿ Timer setting in Minutes or Seconds.
Ÿ Timer run automatically as per setting.
Suggested Wiring GS-UV-C-2 / GS-UV-C-3
Ÿ Timer Hold/start manually.
Ÿ Timer hold at Door open & Buzzer will turn ON at
timer over. 8(1)A 250V MAX

DOOR
LIMIT SWITCH
Introduction
UV Germicidal Irradiation is a disinfection method that uses short-
wavelength ultraviolet (ultraviolet C or UV-C) light to kill or inactivate
microorganisms by destroying nucleic acids and disrupting their DNA,
leaving them unable to perform vital cellular functions. UV Lamp

This controller has timer feature to control UV light automatically as per

time setting. User can Hold/Start the UV light manually by using the key
in a UV-cabinet as per timer setting.

Door open sensing is provided to switch off the UV-Light. Buzzer will be
ON when timer is over.
USER INTERFACE
Touch to increase Timer count value by 1
Caution UP Key Minute/Second.
WIRING: The electrical wiring should be done as shown in the
Touch to decrease Timer count value by 1
diagram. The power supply circuit should be connected to a protection
switch. The terminals admit wires of upto 2.5sq mm. Down Key Minute/Second.
Touch to start or hold the timer.
WARNING: Improper wiring may cause irreparable damage and
personal injury. Kindly ensure that wiring is done by qualified personnel
Also to save the timer count, if it is changed
only. Start/Hold Key by using up/down key.
Touch and hold for 1 sec to stop & reset the
Maintenance: Cleaning: Clean the surface of the controller with a soft
moist cloth. Do not use abrasive detergents, petrol, alcohol or solvents.
Reset Key timer at last saved value.

Notice: The information in this document is subject to change in order

to improve reliability , design or function without prior notice and does
not represent a commitment on the part of the company. In no event will
the company be liable for direct, indirect, special, incidental or
consequential damage arising out of the use or inability to use the
product or documentation, even if advised of the possibility of such
damages. No part of this manual may be reproduced or transmitted in
any form or by any means without the prior written permission of the
company.
Installation : Fixing and dimensions of panel models:
To fix the unit, slide the fastener 1 through the guides 2 as per the
position shown in the figure. Move the fastener in the direction of the
arrow, pressing tab 3 it permits to move the fastener in the opposite
direction of the arrow.

Controller :Controller should be installed in a place protected by

vibration, water and corrosive gasses and where ambient temperature
does not exceed the values specified in the technical data.
 Technical Data Display & LED Indications
Housing : Black ABS Plastic, Auto-extinguish LED Status Description
Front Cover : Polycarbonate Plastic ON Timer is started & Relay output is ON.
Dimensions : Frontal : 78 X 36mm, Depth : 59mm Timer is stopped & Relay output
UV-Light OFF
is OFF.
Panel Cutout : 29 X 71mm
Mounting : Flush panel mounting with fasteners Timer is on hold & Relay output is
Blinking
Protection : IP65 Front (with gasket) Time Delay OFF.

Connections : Screw terminal blocks. < 2.5sq mm terminal

Blinking
Timer is over & Relay output is OFF.
only. for 3 sec
Display : 2 X 17mm 7 segment display Door Door is open & Relay output is OFF.
Open
: 2 LED Icons for Indication
Data storage : Flash APROM memory. To change Timer Measurement unit
Power input : 230 Vac ±15%,50-60Hz Standard. To change the timer unit, touch “ + ” key for 2 sec. Display
Relay output : UV-C SPDT relay 8(1)A, 250V AC will show “ ” if unit is set to minutes & Display will show “ ”
Operating Temp. : 0ºC to 60ºC (non-condensing) if unit is set to seconds. Timer will be set and display will show
“0”. Factory set value is in seconds.
Operating Humidity : 20% to 85% (non-condensing)
Storage Temp. : -25.0ºC to 60.0ºC (non-condensing) To change Timer reset mode at Door Open
Timer Range : 0 to 99 Min/sec (as per setting)
To change the timer reset mode, touch “ + ” key for 10 sec.
Digital Input (Potential Free) : Door Limit Switch Display will show “ ” if timer reset mode is set to Manual &
Buzzer : Internal Display will show “ ” if timer reset mode is Auto at Door Close.
Resolution : +/- 1 Min/Sec (Configurable)
Ordering Information
Working Logic & Functions Sr. No.
Timer Model Brief Description
Door Input
Buzzer
No. Sensing - DI
1. Use / key to set value from 0 to 99. When set to ‘0’
36x78mm,
timer function is inactive. 8(1)A/250vac,
Relay based Timer
2. Example: Timer count value is set to 10, touch the “ ”
1. GS-UV-C-2 in Horizontal Included Internal
and timer will start countdown & Relay will switch ON. After Display
every minute or second, as per unit setting, display count will Orientation. Red
Color.
decrease by 1. Once timer is over, display will blink “ ” for
36x78mm,
3sec & Relay will be OFF. Timer will reset & Display will show 8(1)A/250vac,
2. Relay based Timer Included Internal
last set value of timer that is “10”. GS-UV-C-3
in Vertical Display
3. To start the timer again touch “ ” key. Orientation. Red
Color.
4. Timer is running & if user has touched key, then timer will
stop. Timer will reset and display will show last saved value Disclaimer: This manual & its contents remain the sole property of Selector India
and shall not be reproduced or distributed without authorization. Although great care
that is 10. has been taken in the preparation of this document, the company or its vendors in no
event will be liable for direct, indirect, special, incidental or consequential damage
5. Timer can Start and Hold by “ ” key.
arising out of the use or inability to use the product or documentation, even if advised
6. Relay will switch OFF when Door is open. of the possibility of such damages. No part of this manual may be reproduced or
transmitted in any form or by any means without the prior written permission of the
7. When door is closed, Relay will start auto if timer reset mode is company. Selector India, reserves the right to make and changes or improvements
without prior notice.
set to auto else user has to start manually by “ ” key. Warranty: This product is warranted against defects in materials and workmanship
8. Buzzer will turn ON when timer is over & display will flash “ ” for a period of one year from the date of purchase. During the warranty period,
product determined by us to be defective in form or function will be repaired or, at our
for 3 seconds. option, replaced at no charge. This warranty does not apply if the product has been
damaged by accident, abuse, and misuse or as a result of service or modification
Note:
other than by the company. This warranty is in lieu of any other warranty expressed
Relay will be OFF when below conditions occurs: or implied. In no event shall the company be held liable for incidental or
i. Timer value is changed. consequential damages, including lost revenue or lost business opportunity arising
ii. Timer is reset by key. from the purchase of this product.
iii. Timer is over. 00 / 12.08.2020
iv. Timer Unit is changed.
v. Door is open.