Scribd Logo
Upload

Welcome to Scribd!

  • 7 views

    Higun 175x Eng

    Uploaded by

    andressarueda

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Higun 175x Eng

    Uploaded by

    andressarueda
    7 views2 pages

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    7 views2 pages

    Higun 175x Eng

    Uploaded by

    andressarueda

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    Higun®175XMonolithic

    Product Data Sheet

    ProductDescription
    Higun 175X is 1750°C (3182°F) grade low cement gunning material. Higun combines the superior physical properties of a
    low cement monolithic with the practical advantages of a gunning material. The Higun range of low cement gun mixes are
    designed to be installed with conventional gunning equipment with some accessories to maximize the product properties.

    Instructionsforusing
    Gunning: Higun products must be installed under closely controlled conditions using the proper gunite equipment.

    • Rotary gun recommended

    • Water booster pump capable of delivering up to 15 quarts/minute at >200 psi pressure

    • 18” - 24” nozzle extension (“whip”) past the water ring

    • 16 hole minimum water ring with ≤ 1mm holes

    • Large air compressor to prevent surging

    • 50 – 75 psi air pressure


    Do not pre-dampen material before gunning. Material sets very quickly so cutback should be within 5 - 10 minutes after
    gunning.
    For detailed installation instructions and commissioning schedules, please contact your Morgan Advanced Materials-
    Thermal Ceramics representative.

    Properties Higun175X
    RegionofManufacture Americas
    Bondtype Hydraulic
    Rawmaterialbase Bauxite
    Methodofinstallation Gun
    Maximumgrainsize,mm 7
    Maximumservicetemperature,°C(°F) 1750 (3182)
    Netmaterialrequirement,kg/m3(pcf) 2579 (161)
    Packaginginbags,kg(lbs) 25 (55)

    Whilst the values and application information in this datasheet are typical, they are given for guidance only. The values and the information
    given are subject to normal manufacturing variation and may be subject to change without notice. Morgan Advanced Materials – Thermal
    Ceramics makes no guarantees and gives no warranties about the suitability of a product and you should seek advice to confirm the
    product’s suitability for use with Morgan Advanced Materials - Thermal Ceramics.

    Publication Date: 10 March 2023 www.morganthermalceramics.com


    Code: CA.150 Email: [email protected]
    1 of 2 Thermal Ceramics is a business of Morgan Advanced Materials
    Higun®175XMonolithic
    Product Data Sheet

    Properties Higun175X
    BulkDensity,kg/m3(pcf),ASTMC134
    dried 24 hours @ 105°C (220°F) 2691 (168)
    fired 5 hours @ 816°C (1500°F) 2515-2707 (157-169)
    ColdCrushingStrength,MPa(psi),ASTMC133
    dried 24 hours@110°C 69.0-96.6 (10000-14000)
    fired 5 hours @ 816°C 58.6-75.9 (8500-11000)
    fired 5 hours @1000°C 69.0-96.6 (10000-14000)
    fired 5 hours @1600°C 75.9-103.4 (11000-15000)
    PermanentLinearChange,%,ASTMC113
    dried 24 hours @ 105°C (220°F) 0 to -0.2
    fired 5 hours @ 816°C (1500°F) -0.1 to -0.3
    fired 5 hours @ 1000°C (1832°F) -0.1 to -0.4
    fired 5 hours @ 1600°C (2912°F) -0.1 to -0.4
    Abrasionloss,cm3,ASTMC704
    fired @ 1500°F (816°C) 7-12
    ChemicalAnalysis,%,CalcinedBasis
    Alumina, Al2O3 81
    Silica, SiO2 13
    Ferric Oxide, Fe2O3 1.0
    Titanium Oxide, TiO2 2.7
    Calcium Oxide, CaO 2.8
    Alkali as, K2O+Na2O 0.5
    ThermalConductivity,W/m•K(BTU•in/hr•ft2•°F),ASTMC417
    600°C (1112°F) 1.90 (13.2)

    StorageandShelfLife
    • Monolithics should be stored in a dry, well-ventilated area and held off the ground on pallets ideally with the original
    packaging intact. Keep out of rain and damp conditions.
    • Normal shelf life is 6 months from date of manufacture when properly stored.

    Whilst the values and application information in this datasheet are typical, they are given for guidance only. The values and the information
    given are subject to normal manufacturing variation and may be subject to change without notice. Morgan Advanced Materials – Thermal
    Ceramics makes no guarantees and gives no warranties about the suitability of a product and you should seek advice to confirm the
    product’s suitability for use with Morgan Advanced Materials - Thermal Ceramics.

    Publication Date: 10 March 2023 www.morganthermalceramics.com


    Code: CA.150 Email: [email protected]
    2 of 2 Thermal Ceramics is a business of Morgan Advanced Materials

    You might also like