5.3.

7 Lab - Introduction to Wireshark

This lab has been updated for use on NETLAB+.

www.netdevgroup.com

Mininet Topology

Objectives
Part 1: Install and Verify the Mininet Topology
Part 2: Capture and Analyze ICMP Data in Wireshark

Background / Scenario
The Workstation VM includes a Python script that, when you run it, will set up and configure the devices
shown in the figure above. You will then have access to four hosts, a switch, and a router inside your one VM.
This will allow you to simulate a variety of network protocols and services without having to configure a
physical network of devices. For example, in this lab you will use the ping command between two hosts in the
Mininet Topology and capture those pings with Wireshark.

 2018 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 1 of 7 www.netacad.com
5.3.7 Lab - Introduction to Wireshark

Wireshark is a software protocol analyzer, or "packet sniffer" application, used for network troubleshooting,
analysis, software and protocol development, and education. As data streams travel over the network, the
sniffer "captures" each protocol data unit (PDU) and can decode and analyze its content according to the
appropriate RFC or other specifications.
Wireshark is a useful tool for anyone working with networks for data analysis and troubleshooting. You will
use Wireshark to capture ICMP data packets.

Instructions

Part 1: Install and Verify the Mininet Topology

In this part, you will use a Python script to set up the Mininet Topology inside the Workstation VM. You will
then record the IP and MAC addresses for H1 and H2.

Step 1: Verify your PC’s interface addresses.

Launch the Workstation VM. Log on to the Workstation VM as the analyst, using the password
cyberops and open a terminal window.

Step 2: Run the Python script to install the Mininet Topology.

Open a terminal emulator to start Mininet and enter the following command at the prompt. When
prompted, enter cyberops as the password.
[analyst@secOps ~]$ sudo ~/lab.support.files/scripts/cyberops_topo.py
[sudo] password for analyst:

Step 3: Record IP and MAC addresses for H1 and H2.

a. At the mininet prompt, start terminal windows on hosts H1 and H2. This will open separate windows for
these hosts. Each host will have a separate configuration for the network including unique IP and MAC
addresses.

 2018 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 2 of 7 www.netacad.com
5.3.7 Lab - Introduction to Wireshark

*** Starting CLI:

mininet> xterm H1
mininet> xterm H2
b. At the prompt on Node: H1, enter ip address to verify the IPv4 address and record the MAC address. Do
the same for Node: H2. The IPv4 address and MAC address are highlighted below for reference.
[root@secOps analyst]# ip address
<output omitted>
2: H1-eth0@if3: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP
group default qlen 1000
link/ether ba:d4:1d:7b:f3:61 brd ff:ff:ff:ff:ff:ff link-netnsid 0
inet 10.0.0.11/24 brd 10.0.0.255 scope global H1-eth0
valid_lft forever preferred_lft forever
inet6 fe80::b8d4:1dff:fe7b:f361/64 scope link
valid_lft forever preferred_lft forever

Host-interface IP Address MAC Address

H1-eth0
H2-eth0

Part 2: Capture and Analyze ICMP Data in Wireshark

In this part, you will ping between two hosts in the Mininet and capture ICMP requests and replies in
Wireshark. You will also look inside the captured PDUs for specific information. This analysis should help to
clarify how packet headers are used to transport data to the destination.

Step 1: Examine the captured data on the same LAN.

In this step, you will examine the data that was generated by the ping requests from H1 to H2. Wireshark data
is displayed in three sections:
o The top section displays the list of PDU frames captured with a summary of the IP packet information
listed.
o The middle section lists PDU information for the frame selected in the top part of the screen and
separates a captured PDU frame by its protocol layers.
o The bottom section displays the raw data of each layer. The raw data is displayed in both
hexadecimal and decimal form.

 2018 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 3 of 7 www.netacad.com
5.3.7 Lab - Introduction to Wireshark

a. On Node: H1, enter wireshark & to start Wireshark (If a pop-up warning pops up, click OK to continue).
[root@secOps analyst]# wireshark &
[1] 3118
[root@secOps analyst]# QStandardPaths: XDG_RUNTIME_DIR not set, defaulting to
‘/tmp/runtime-root’
b. In the Wireshark window, under the Capture heading, select the H1-eth0 interface. Click Start to capture
the data traffic.

c. On Node: H1, press the Enter key, if necessary, to get a prompt. Then type ping -c 5 10.0.0.12 to ping
H2 five times. The command option -c specifies the count or number of pings. The 5 specifies that five
pings should be sent. The pings will all be successful.
[root@secOps analyst]# ping -c 5 10.0.0.12
d. Navigate to the Wireshark window, click Stop to stop the packet capture.

 2018 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 4 of 7 www.netacad.com
5.3.7 Lab - Introduction to Wireshark

e. A filter can be applied to display only the interested traffic.

Type icmp in the Filter field and click Apply.
f. If necessary, click the first ICMP request PDU frames in the top section of Wireshark. Notice that the
Source column has H1’s IP address, and the Destination column has H2’s IP address.

g. With this PDU frame still selected in the top section, navigate to the middle section. Click the arrow to the
left of the Ethernet II row to view the Destination and Source MAC addresses.

Question:

Does the Source MAC address match H1’s interface?

Type your answers here.
Does the Destination MAC address in Wireshark match H2’s MAC address?
Type your answers here.
Note: In the preceding example of a captured ICMP request, ICMP data is encapsulated inside an IPv4
packet PDU (IPv4 header) which is then encapsulated in an Ethernet II frame PDU (Ethernet II header)
for transmission on the LAN.

Step 2: Examine the captured data on the remote LAN.

You will ping remote hosts (hosts not on the LAN) and examine the generated data from those pings. You will
then determine what is different about this data from the data examined in Part 1.
a. At the mininet prompt, start terminal windows on hosts H4 and R1.
mininet> xterm H4
mininet> xterm R1
b. At the prompt on Node: H4, enter ip address to verify the IPv4 address and record the MAC address.
Do the same for the Node: R1.
[root@secOps analyst]# ip address

Host-interface IP Address MAC Address

H4-eth0
R1-eth1
R1-eth2

 2018 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 5 of 7 www.netacad.com
5.3.7 Lab - Introduction to Wireshark

c. Start a new Wireshark capture on H1 by selecting Capture > Start. You can also click the Start button or
type Ctrl-E Click Continue without Saving to start a new capture.
d. H4 is a simulated remote server. Ping H4 from H1. The ping should be successful.
[root@secOps analyst]# ping -c 5 172.16.0.40
e. Review the captured data in Wireshark. Examine the IP and MAC addresses that you pinged. Notice that
the MAC address is for the R1-eth1 interface. List the destination IP and MAC addresses.
Question:

IP address:
Type your answers here.
MAC address:
Type your answers here.
f. In the main CyberOps VM window, enter quit to stop Mininet.
mininet> quit
*** Stopping 0 controllers

*** Stopping 4 terms

*** Stopping 5 links
.....
*** Stopping 1 switches
s1
*** Stopping 5 hosts
H1 H2 H3 H4 R1
*** Done

g. To clean up all the processes that were used by Mininet, enter the sudo mn -c command at the prompt.
analyst@secOps ~]$ sudo mn -c
[sudo] password for analyst:
*** Removing excess controllers/ofprotocols/ofdatapaths/pings/noxes
killall controller ofprotocol ofdatapath ping nox_core lt-nox_core ovs-openflowd ovs-
controller udpbwtest mnexec ivs 2> /dev/null
killall -9 controller ofprotocol ofdatapath ping nox_core lt-nox_core ovs-openflowd
ovs-controller udpbwtest mnexec ivs 2> /dev/null
pkill -9 -f "sudo mnexec"
*** Removing junk from /tmp
rm -f /tmp/vconn* /tmp/vlogs* /tmp/*.out /tmp/*.log
*** Removing old X11 tunnels
*** Removing excess kernel datapaths
ps ax | egrep -o 'dp[0-9]+' | sed 's/dp/nl:/'
*** Removing OVS datapaths
ovs-vsctl --timeout=1 list-br
ovs-vsctl --timeout=1 list-br
*** Removing all links of the pattern foo-ethX
ip link show | egrep -o '([-_.[:alnum:]]+-eth[[:digit:]]+)'
ip link show
*** Killing stale mininet node processes
pkill -9 -f mininet:
*** Shutting down stale tunnels
pkill -9 -f Tunnel=Ethernet

 2018 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 6 of 7 www.netacad.com
5.3.7 Lab - Introduction to Wireshark

pkill -9 -f .ssh/mn
rm -f ~/.ssh/mn/*
*** Cleanup complete.
End of document

 2018 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 7 of 7 www.netacad.com