Service Manual: Vision Vacuum Cleaner HR 8900
Service Manual: Vision Vacuum Cleaner HR 8900
Service Manual: Vision Vacuum Cleaner HR 8900
Service Information
Service Information
Service Information
Service Manual
PRODUCT INFORMATION
Maximum air displacement Maximum vacuum water column Power consumption (IEC) Dust storage capacity Cord length Filter system (depends on version) : : : : : : : : : : : : 37 l/sec. 310 cm 1500W 4 litres 8.3 metres Paper dustbag Exhaust air lter Motor inlet lter 48 x 30 x 25 cm 6.4 kg 78 dB Orange / grey
SERVICE INFORMATION
- The infrared remote control can adjust the suction power with 5 speeds. When switched on, the appliance always starts with the highest power, even without a connected hose. Use LR03 batteries. Alkaline is advised. - To open the appliance, rst remove the panel (item 13) with a big screw driver (V) to disconnect the 4 snap locks (the 4 screws of button panel item 39 can be loosed) and then remove the two pedals (items 1 and 14) with a pin (W), max. diameter 2.5 mm. - Power meter (8838 000 60300) is a commercial item with a xed air displacement which measures the vacuum of the appliance. - Component conguration on exploded view may differ in case of specic versions. However, the actual components are distinguished by means of code numbers. - The spare parts have been standarized as much as possible. - Item 7A. This appliance is provided with ring 7A. For other parts use item 6 or 7. - Item 16 Cotton dustbag is used in those countries where paper dustbags are not available. - Item 21 is provided with the long cord-winder spring; both long and short cords can be used in combination with this spring. - To disassemble the cordwinder use TORX screw driver no T15, which is one of a set consisting of T20, T15, T10, T9, T8, T7 and T6 = 4822 395 50145. - Item 43 air valve opens to cool the motor if the air displacement is too low or if the air ow is blocked. - Cordwinder spring has to be tensioned till maximum minus approx. 1,5 revolution.
OPTIONAL
Exhaust air lter Oslo cotton dustbag Oslo paper dustbag set Oslo paper dustbag set Oslo 3-M dustbag Active carbon inlet lter Active carbon lter set S-class lter S-class lter set Polishing nozzle Turbo brush HR 6932 (8836 932 01210) HR 6935 (8836 935 01010) HR 6938 (8836 938 06110) economy HR 6938 (8836 938 10110) hygiene HR 6938 (8836 938 91010) HR 6949 (8836 949 01010) HR 6968 (items 41 + 42) HR 6992 (8836 992 01010) HR 6993 (items 48 + 49) HR 8040 (item 111) HR 6988 (item 114)
This product meets the requirements regarding interference suppression on radio and TV.
After the product has been repaired, it should function properly and has to meet the safety requirements as ofcially laid down at this moment.
Copyright reserved
Subject to modification
1 2 3 4 5 6 7 7A 8 9 10 11 12 13 14 15 16
4322 003 17180 4322 003 17140 4322 009 07090 4322 003 17130 4322 005 06650 4322 001 72800 4322 009 06420 4322 003 15820 4322 001 71960 4322 003 17110 4322 000 03800 4322 003 17120 4322 003 10630 4322 005 11810 4322 003 17170 4322 006 22410 8836 938 10110 8836 935 01010 8836 938 91010 4322 005 06610 4322 009 06410 4322 009 06390 4322 009 05350 4322 003 10470 4322 001 72360 4322 009 04800 4322 009 05060 4322 006 01800 4322 006 00550 4322 006 01810 4322 006 00540 4322 003 16960 4322 005 04700 4322 000 03790 4322 001 98860 4322 005 04750 4322 006 50580 4322 003 17150 4322 003 16970 4322 000 37300 8836 949 01010 4322 009 07040 4322 003 10950
cord-winder pedal accessory cover acc. cover spring lead lid acc. cover lock diaphragm valve swivel connector ring sealing rubber dust cover dust-cover spring dust-cover snaplock cord-winder lever version panel switch pedal IR-RMC receiver oslo paper dustbag hyg. oslo cotton dustbag (opt.) oslo 3M-dustbag (opt.) hose + connectors dustbag holder dust chamber reel half spring unit connection piece brake tyre reel half contact unit contact-ring plate cordset UK 1 mm2 L = 8.3 m cordset 1 mm2 L = 8.3 m 4.8 mm pins cordset Swiss 1 mm2 L = 8.3 m cordset Italy 1 mm2 L = 8.3 m lower housing caster assy button spring switch lever parking hook main switch button panel upper housing safety lter Trio carbon lter safety lter + grille grille for carbon lter
MAIN SWITCH
43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 101 102 103 104 105 111 112 113 114 115 116 117 121 122 124 125 126 128 129 130 131 DFU DFU DFU
4322 005 04730 4322 006 22460 4322 005 07920 4322 003 17160 4322 003 17000 4322 003 16990 4322 003 17700 8836 992 01010 8836 932 01210 4322 009 07460 4322 009 06450 4322 001 72790 4322 003 09720 4322 000 03700 4322 009 06430 4322 001 72780 4322 003 09820 4322 009 05400 4322 004 22150 4322 009 05410 4322 004 22180 4322 004 22120 4322 004 22030 4322 005 11040 8838 041 01010 4322 004 22130 9965 000 03349 4822 358 10205 4822 479 20201 4322 001 99120 4322 007 45550 4322 007 16000 4322 005 08690 4322 003 16030 4322 006 20590 4322 003 02070 4322 004 00650 4322 004 00590 4222 000 47300 4222 000 47280 4222 000 45620
air inlet valve 220-240V power module 230V rear wheel rear wheel cap cord outlet S-lter grille back grille S-lter AFS lter motor housing silencers back motor buffer suspension bracket PCB mounting spring motor 1441 - 230V front motor buffer motor disc tube clip assy 32 mm tube chr. active coupling tube clip assy 35 mm (opt.) (opt.)
(opt.) (opt.)
17 18 20 21 22 23 24 25 28 29 30 31 32 33 35 36 37 38 39 40 41 42
telesc. tube + clamp nozzle RD 262 act. coupl. Polishing nozzle HR 8040 Polishing disc Polishing brushes HR 8041 turbo nozzle coupling piece drive belt Brush assy coupling bush coupling spring leafspring hose + standard bend bend RMC IR-RMC send unit crevice nozzle small nozzle brush nozzle vacuum cleaner polishing nozzle turbo brush HR 8040 HR 6988 HR 6988
(opt.) (opt.)
V W
CORD WINDER
PMT
IR
W
IR-TRANSMITTER
M
MOTOR POWER MODULE IR-RECEIVER + CONTROL
12 13 14
15
16 4 5
17
18
7A
20 2131 7 8 9 10 32 6
11 33
(4x)
47 35 36 37 38 39 48
40 49
50
41 42 51
43
52 53 54
44 45
55
56 57 46
AUSTRALIA
26 27 28
EUROPE 4.8mm
29 30 31
FLAT PINS
CH
22
GB
ITALY
23
24 21 B 25
125
126
124 128
129
130
131
115
101
103
102
104
105
112
111
113
DAP1193