Scribd Logo
Upload

Welcome to Scribd!

  • 602 views

    Radiography Cheat Sheet

    Uploaded by

    bplturner
    Radiographic testing (RT) is used to ensure the structural integrity of welded joints in pressure vessels like deaerators. There are several levels of RT that can be specified, with higher levels allowing thinner materials by providing greater joint efficiencies. RT1 requires 100% radiography of all seams and large nozzle welds, providing a 1.0 joint efficiency. RT2 requires 100% radiography of longitudinal seams and spot checks of circumferential seams, with a 1.0 efficiency. RT3 uses spot checks on all seams and has a 0.85 efficiency. Engineers should consider safety, cost and quality assurance when deciding which RT level to specify.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd

    Radiography Cheat Sheet

    Uploaded by

    bplturner
    602 views1 page
    Radiographic testing (RT) is used to ensure the structural integrity of welded joints in pressure vessels like deaerators. There are several levels of RT that can be specified, with higher levels allowing thinner materials by providing greater joint efficiencies. RT1 requires 100% radiography of all seams and large nozzle welds, providing a 1.0 joint efficiency. RT2 requires 100% radiography of longitudinal seams and spot checks of circumferential seams, with a 1.0 efficiency. RT3 uses spot checks on all seams and has a 0.85 efficiency. Engineers should consider safety, cost and quality assurance when deciding which RT level to specify.

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Radiographic testing (RT) is used to ensure the structural integrity of welded joints in pressure vessels like deaerators. There are several levels of RT that can be specified, with higher levels allowing thinner materials by providing greater joint efficiencies. RT1 requires 100% radiography of all seams and large nozzle welds, providing a 1.0 joint efficiency. RT2 requires 100% radiography of longitudinal seams and spot checks of circumferential seams, with a 1.0 efficiency. RT3 uses spot checks on all seams and has a 0.85 efficiency. Engineers should consider safety, cost and quality assurance when deciding which RT level to specify.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    602 views1 page

    Radiography Cheat Sheet

    Uploaded by

    bplturner
    Radiographic testing (RT) is used to ensure the structural integrity of welded joints in pressure vessels like deaerators. There are several levels of RT that can be specified, with higher levels allowing thinner materials by providing greater joint efficiencies. RT1 requires 100% radiography of all seams and large nozzle welds, providing a 1.0 joint efficiency. RT2 requires 100% radiography of longitudinal seams and spot checks of circumferential seams, with a 1.0 efficiency. RT3 uses spot checks on all seams and has a 0.85 efficiency. Engineers should consider safety, cost and quality assurance when deciding which RT level to specify.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 1

    #111

    Radiographic Testing (RT) of Deaerator Vessels


    The purpose of radiography of pressure vessels is to insure the structural integrity of welded joints on the vessel. The amount of radiography used affects the head and shell thickness and the vessel cost. Generally, if more radiographs are taken, thinner materials can be used. This technical paper is meant to be used for informational purposes only. The ASME Code should be referred to for specific questions and applications. There are several levels of radiography that should be considered by engineers who write specifications for deaerators. ASME Section VIII, Div.1, Par. UG-116 defines the following: 1. RT1 This designation indicates that 100 % of all longitudinal and circumferential seams have been radiographed. It also indicates that 100 % of nozzle welds over 10 diameter and of weld neck design have been radiographed. This level yields a 1.0 joint efficiency on all welds. RT1 is mandatory for head/shell thickness greater than 1.25 (ASME SA-516-70). 2. RT2 This designation indicates that 100 % of longitudinal weld seams have been radiographed and that spot RT has been done on circumferential seams. This level yields a 1.0 joint efficiency for thickness calculations. No radiographic testing is done on nozzle welds for this level. This is defined in Par. UW-11(a)5 and UW-11(a)(5)(b). 3. RT3 This level requires spot RT on all longitudinal and circumferential seams and yields a 0.85 joint efficiency. No nozzle connection welds have RT performed on them. This is defined in UW-11(b) and UW-52. 4. RT4 This is defined as any level of RT performed, but not defined by RT1, RT2, or RT3. 5. Vessels designed to ASME code, Section I require 100% RT on circumferential and longitudinal seams and certain nozzles as defined by the ASME Code. Each specifying engineer should consider safety, cost and quality assurance before deciding which level of RT to include on a given deaerator.

    This Tech Sheet was developed by the members of the Heat Exchange Institutes (HEI) Deaerator Section. HEI is a trade association comprising the leading manufacturers of heat exchange and vacuum equipment. HEI Tech Sheets are information tools and should not be used as substitutes for instructions from individual manufacturers. Always consult with individual manufacturers for specific instructions regarding their equipment.
    09/13/05 Page 1 of 1

    This sheet is reviewed periodically and may be updated. Visit www.heatexchange.org for the latest version.

    You might also like