PCS(Personal communications services)

Personal communications services (PCS) refers to a wide variety of wireless access and personal mobility
services provided through a small terminal. with the oal of enabling communications at any time, at any
Place , and in any form. . ~~'tMCl\~oJ\.
eaJ€
(VI..J~tre A~eJ"~
- •. b. r •. .h_
j -
~ "'a"~- ~~~~t'
fvt~)~A":-
Broad range of voice and data telecommunications services that enable people to communicate via two-way
radio phones based exclusively on digital technologies such as COMA and GSM. Characteristics of PCS
-
include personal numbers assigned to individuals rather than devices, near-wireline-call-transmission
quaiity, low-power and lightweight mobile devices, enhanced call completion, call billing and call
management
,
services. PCS networks operate at I 800M Hz in the U.K. and at 1900MHz in North America.
~--

PCS technologies have grown rapidly in the telecommunications industry.

Explain PCS architecture.

L.JL
r'\E:) f'\ t-<~ . /,... ....
t £q-vw
'beJc­
\<:~cJtl
t~~T'JrtJ'~~ ~~5
. r\~ & J,e
f'~" l:.. ~
L ..c: ~!'CI 0 - Station
"biA s-flo# ~ rv­ ~:stl'D15 (BSS)
A.I1L~ J.-::~!.(
.~1~K: eke' r~A~ g,'<n~~c NP~f. Qr-th~ ,~~
"B'Y",J., <Jd(.I<!fSLTJ~~·~Ov. ~~U\A d.-t.~ t.J ~,. . . p.,~
pcs architectLire has mainly 3 types of Interfaces
• Um intelface The "air" or radio interface standard that is used for exchanges between a mobile
-
(ME) and a base station (BTS / BSe). For signalling, a modified version of the ISDN LAPD, known as
WDm is used. '
• Abis interface This is a BSS internal interface linking the BSC and a BTS, and it has not been
totally standardised. The Abis interface allows control of the radio equipment and radio frequency allocation
in the BTS . ~_
. ... A interface The A interface is used to provide communication between the BSS and the MSC-:-"' ~i~
PCS architecture divides into to 3 subsystem i.e.Base Station Subsystem(BSS),Network Switching
Subsystem (NSS) and Operation and Support Subsystem (OSS)
'* Mobile station
pes use mobile stations (MSs) to communicate with the base stations (BSs) in a PCS network.
MS is also.referred to as handset, mobile phone. subscriber unit, or portable.
;Vlobile stations eMS), mobile equipment (ME) or as they are most widely knov\ln, cell or mobile phones are
..the section ofa GSM cellular network .
 * In recent years their size has fallen dramatically while the level offunCtiona[ity has greatly increased.
There are a number of elements to the cell phone, although the two main elements are the main hardware
and the SIM.
It contains a number known as the Internationa[ Mobi[e Equipment Identity (IMEI) . This is installed in the
phone at manufacture and "cannot" be changed . .!.! is accessed by the network durin g registration to check
.whether the equipment has been reported as stolen.
The SIM or Subscriber Identity Module contains the information that provides the identity of the user to the
network. It contains are variety of information including a number known as the International Mobile
§ ubscri~~~Tcld~entlty
~~~~~TS~I
(rM ' R)=========================================================
.
#- Base Station Subsystem (BSS)
The Base Station Subsystem (BSS) section of the GSM network architecture that is fundamentally
associated with communicating with the mobiles on the network. It consists of two elements:
• , Base Transceiver Station (BTS): The BTS used in a GSM network comprises the radio transmitter
receivers, and their associated antennas that transmit and receive to directly communicate with the mobiles.
• 2 .

The BTS is the defining element for each cell. '"[he BTS communicates with the mobiles and the interface
between the two is known as the Um interface with its associated protocols.
• Base Station Controller (BSC): The BSC forms the next stage back into the GSM network. J!.
controls a group of BTSs, and is often co-located with one of the BTSs in its group. It manages the rad io

.
resources and controls items such as hand over within the group of BTSs, allocates channels and the like . It
communicates with the BTSs over what is termed the Abis interface.
:#=- Network Switching Subsystem (NSS)
The GSM system architecture contains a variety of different elements, and is often termed the core network.
It provides the main control and interfacing for the whole mobile network. The major elements within the
t ore n etwo r~ Incl ude : lj\·{~ae.of ~..n'('.e.4 0<~.f.cJ jU~c
• Mobile Services Switching Centre (MSC): The main element withi n the core network area of the
overall GSM network architecture is the Mobi[e swi'tchin Services Centre (MSC). The MSC acts like a
normal switching node within a PSTN or ISDN, but also provides additional functionality to enabl e the
I equirements of a mobile user to be su pported. 1 hese include registration, authentication, call location, inter­
MSC handovers .and call routing to a mob ile su bscrIber. It a lso provIdes an interface to the PSTN so that
Zills can be routed from the mobile network to a phone connected to a [and[ine. Interfaces to other MSCs
are provided to enable calls to be made to mobiles on different networks.
• !lome Location Register (HLR): This database contains a[[ the administrative information about
~ach subscriber along w ith their last known location. In this way, the GSM network is able to route ca[l s to
the relevant base station for the MS. When a user switches on their phone, the phone registers with the
network and from this it is possible to determine which BTS it communicates with so that incoming calls
can be routed appropriately. Even when the phone is not active (but switched on) it re-reg isters periodically
~----~~~~-'~~·'~~~====~~~~~7=~~==~~Trr~~~~~~~~~,
to ensure that the network (HLR) IS aware of ItS latest pOSItIOn. ~here IS one ALR per network, although It
may be distributed across various su b-centres to for operational reasons. .
• Visitor Location Register (VLR): This contains selected information from the HLR that enables the
selected services for the individual subscriber to be provided. The VLR can be implemented as a separate
entIty, but It IS commonly rea lIsed as an Integral part of the MSC, rather than a separate entiti:. In this way
~ccess is made faster and more convenient. ­
• Equipment Identity Register (EIR): The EIR is the entity that decides whether a given mobile
equipment may be allowed onto the network. Each mobile equipment has a number known as the
International Mobile Equipment Identity. This number, as mentioned above, is installed in the equipment
(T,v... G '1)
 ar.d is checked by the network duri ng registration. Dependent upon the information held in the EIR, the
..mobile mav,," be allocated one of three states - all owed onto the network. barred access, or monitored in case
its problems::
• • Authentication Centre (AuC): The AuC is a protected database that contains the secret key also
contained in the user's SIM card. "~~ i~ used for authentication and for ciphering on the radio channel.
• Gateway Mobile Switching Centre (GMSC): The GMSC is the point to which a ME terminating
.....
call is initially routed, without any knowledge of the MS 's location. The GMSC is thus in charge of
.obtaining the MSRN (Mobile Station Roaming Number) from the HLR based on the MSISDN (Mobile
~tation ISDN number, the "directory number" of a MS) and routing the call to the correct visited MSe. The
"MSC" part of the term GMSC is misleading, since the gateway operation does not require any linking to an
MSe.
::#' Operation and Support Subsystem (OSS)
The OSS or operation support subsystem is an element within the overall GSM network architecture that is
•
connected to components of the NSS and the BSe. It is used to control and monitor the overall GSM
to

network and it is also used to control the traffic load of the BSS. It must be noted that as the nu mber of BS
increases with the scaling of the subscriber population some of the maintenance tasks are transferred to the
BTS, allowing savings in the cost of ownership of the system. evJ:~tS'" II
~~ ~~

..c:
,

.........,.. otP»~ r /<11/ ~~. ~~

H d<
~ ~ ~~lligh Speed ~ircuit (HSCSD~
Switched Dataju-+
/7 ? -t C; ~~.~ /I..!j.J. ~ If ,b~ ~AkOz!. ~ ~i ~
High Speed Circllit Switched Data (HSCSD) is an enhancement in the data rate of circuit switched data in a I.e ~
GSM network. HSCSD uses two techniques to increase the data rate. First, HSCSD makes it possible to use
~ ore than one time slot. GSM uses time division multi ple access (TDMA). Each radio channel is divided !!l-
eight time slots ~ Each time slot is allocated to a different user. This makes it possible to serve eight
customers on one radio channel. HSCSD makes it possible to all ocate mo re than one time slot to a user.
The second technique used by HSCSD is that the error correction can be adapted to the quality of the radio
ch annel. ~ standard slot can carry 9.6 kbps. HSCSD makes it' possible to increase this to 1 4.4 kbps. The"
quality of the radio channel must be good enough to do so.
The maximum data rate ofa HSCSD configuration with 14.4-kbps channel coding is 115.2 kbps, ifall eight
time slots are allocated to the same user. In practice, is the number of time slots allocated to a user limited to
three, limiting the data rate to 43 .2 kbps. Another point is that the core network is based on circuit switched
data with data channels of 64 kbps.
The main benefit of HSCSD compared to other data enhancements introduced later is that it is an
inexpensive way to implement higher data rates in GSM networks. There modifications to be made are
relatively small.
 MS BTS

A new functionality is introduced at the network and MS to provide the functions of combining and
splitting the data into separate data streams which will then be transferred via n channels at the radio
interface, where n = I, 2, 3, ... 8. Once split, the data streams shall be carried by the n full rate traffic
channels, called HSCSD channels, as if they were independent of each other, for the purpose of data relay
and radio interface L I error control, until to the point in the network where they are combined. However,
logically the n ful I rate traffic channels at the rad io interface belong to the same HSCSD configuration, and
therefore they shall be controlled as one radio link by the network for the purpose of cellular operations, e.g.
handover.
GPRS (General Packet Radio System)

S!eneral Packet Radio Systel,!l is also known as GPRS is a third-generation step toward internet access.
9PRS is also known as GSM-IP that is a Global-System Mobile Communications Internet Protocol as it

. ~
Division Multiple Access (TDMA) users benefit from this system as it provides packet radio access.
­
keeps the users of this system online, allows to make voice calls, and access internet on-the-go. Even Time­

GPRS also permits the network operators to execute an Internet Protocol (lP) based core architecture for
integrated voice and data applications that will continue to be used and expanded for 3G services.
The GPRS specifications are written by the European Telecommunications Standard Institute (ETS!), the
~uropean counterpart of the American National Standard Institute (ANSl1
Key Features
Following three key features describe wireless packet data
• The always online feature - Removes the dial-up process, making applications only one clic.k
away.
• An upgrade to existing systems - Operators do not have to replace their equipment; rather, GPRS
is added on top of the existing infrastructure.
• An integral part of future 3G systems - GPRS is th e packet data core network for 3G system2,
EDGE and WCDMA. _.

Goals of GPRS
GPRS is the first step toward an end-to-end wireless infrastructure and has the following goals:
...
• Open ar<~ hitect ure.
• Consistent IP services
• Same infrastructure for different air interfaces
• Integrated telephony and Internet infr'astructure
 • Leverage industry investment in IP
• 'Service innovation independent of infrastructure...

Benefits of GPRS

Higher Data Rate

GPRS benefits the users in man y ways, one of which is higher data rates in turn of shorter access times. In
the typical GSM mobile. setup alone is a lengthy process and equally. rates for data permission are
restrained to 9.6 kbit/s. The session establishment time offered while GPRS is in practice is lower than one
second and ISDN-line data rates are up to many " kbitls.
"--?11 ' ~,+-s (~~
Easy Billin ~
GPRS packet transmission offers a more user-friendly billing than that offered by circuit switched services.
In circuit switched services, billing is based on the duration of the connection. This is unsuitable for
applications with bursty traffic. The user must pay for the entire airtime, even for idle periods when no
packets are sent (e.g., when the user reads a Web page).
In contrast to this, with packet switched services, billing can be based on the amount of transmitted data.
-the advantage for the llser is that he or she can be "online" over a long period of time but will be billed
based on the transmitted data volume.

GPRS - Applications
• Communications - E-mail, fax , unified messaging and intranet/internet access, etc.
• Value-added services - Information services and games, etc.
-
• E-commerce - Retail , ticket purchasing, banking and financial trading, etc.
• Location-based applications - Navigation , traffic conditions, airline/rail schedules and location
finder, etc.
• Vertical applications - Freight delivery , fleet management and sales-force automation.
• Advertising - Advertising may be location sensitive. For example, a user entering a mall can
re'Zeive advertisements specific to the stores in that·mall.

GPRS - Architecture
GPRS architecture works on the same procedure like GSM network, but, has additional entities that allow
packet data transmission. This data network overlaps a second-generation GSM network providing packet
, -.----------------~------~----------------~~--~~----
data transport at the rates from 9.6 to 171 kbps. Along with the packet data transport the GSM network
accommodates mUltiple users to share the same air interface resources concurrently.
Following is the GPRS Architecture diagram:
 Signalling
V- __ Circuit Switched GSM
Packet Switched Data
GPRS attempts to reuse the existing GSM network elements as much as possible,
packet-based mobile cellular network, some new network elements, interfaces, and I n rr, trv' " Is for handling
packet traffic are req u i reo.

Therefore, GPRS Modification or Upgrade Required for GPRS.

requires modifications to
numerous GSM network
elements as summarized
below: GSM Network
Element
Mobile Station (MS) New Mobile Station is required to access GPRS services. These
new terminals will be backward compatible with GSM for voice
calls.

BTS A software upgrade is

required in the existing Base Transceiver Station(BTS).

BSC The Base Station Controller (BSC) requires a software upgrade

and the installation of new hardware called the packet control unit
(PCU). The PCU directs the data traffic to the GPRS network and
can be a separate hardware element associated with the BSe.
GPRS Support Nodes The deployment of GPRS requires the installation of new core
(GSNs) network elements called the serving GPRS support node (SGSN)
and gateway GPRS support node (GGSN).
Datab.ases (HLR, VLR, All the databases involved in the network will require software
etc.) upgrades to handle the new call
models and functions introduced by GPRS.
GPRS Mobile Stations

the enhanced air interface or packet data. A variety of MS can exist, including a high-speed version of
c urrent phones to support high-speed data access, a new PDA device with an embedded GSM phone, and
PC cards for laptop computers. These mobile stations are backward compatible for making voice calls using
GSM. FR1 ~~~~ ~J"u,,'Jt.

GPRS Base Station Subsystem * ~

~:p~ ~ e,f~~ tlA-o
:
§.ach BSC requires the installation of one or more Packet Control Units (PCUs) and a software upgrade. The
PCU provides a physical and logical data interface to the Base Station Subsystem (BSS) for packet data
traffic. The BTS can also require a software upgrade but typically does not require hardware enhancements.
When either voice or data traffic is originated at the subscriber mobile, it is transported over the air interface
to the BTS, and from the BTS to the BSC in the same way as a standard GSM call. However, at the output
of the SSC, the traffic is separated; voice is sent to the Mobile Switching Center (MSC) per standard GSM,
and data is sent to a new device called the SGSN via the PCU over a Frame Relay interface.

GPRS SUppOl1 Nodes

Following two new com ponents, called Gateway GPRS Support Nodes (GSNs) and, Serving GPRS Suppo.!:!
Node (SGSN) are added:

Gateway GPRS Support Node (GGSN)

The Gateway GPRS Support Node acts as an interface and a router to external networks. It contains routing
lnformation for GPRS mobiles, which is used to tunnel packets through the IP based internal backbone to
the correct Serving GPRS Support Node. The GGSN also collects charging information connected to the use
of the external data networks and can act as a packet filter for.incoming traffic.

Serving GPRS Support Node (SGSN)

The Serving GPRS Support Node is responsible for authentication of GPRS mobiles, registration of mobiles
i~ the network, mobility management, and collecting information on charging for the ~e of the air interface.

Internal Backbone
The internal backbone is an IP based network used to carry packets between different GSNs. Tunnelling is
used between SGSNs and GGSNs, so the internal backbone does not need any information about domains
outside the GPRS network. Signaling from a GSN to a MSC , HLR or EIR is done using SS7.

Routing Area
GPRS introduces the concept of a Routing Area. This concept is simil ar to Location Area in GSM, except
that it generally contains fewer cells. ~ecause routing areas are smaller than location areas, less radio
resources are used wh iIe broadcasting a page message.

GPRS - Quality of Service

. QoS is a vital feature of GPRS services as there are different QoS support requirements for assorted
The
GPRS applications like realtime multimedia, web browsing, and e-mail transfer.
GPRS allows defining QoS profiles using the following parameters:
• Service Precedence
• Reliability
• Delay and
• Throughput

These parameters are described below:

Service Precedence
The preference given to a service when compared to another service is known as Service Precedence. This
level of priority is classified into three levels called:
• high
• normal
• low
When there is network congestion, the packets of low priority are discarded as compared to high or normal
priority packets.

Reliabilitv
This parameter signifies the transmission characteristics required by an application. The reliability classes
are defined which guarantee certain maximum values for the probability of loss, duplication, mis­
sequencing, and COITuption of packets.

EDGE (Enhanced Data Rate for GSM Evolution)

A higher bandwidth version of GPRS with speeds of up to 384Kbps, or twice that available from GPRS
alone.
It has been evolved from GSM, which is the prevailing standard throughout Europe and the Asia Pacific
region.
For GSM providers, this new technology will increase data rates of both circuit switching (HSCSD) and
packet switching (GPRS) by a factor of 20 to 30 times.

Delay
The delay is defined as the end-to-end transfer time between two communicating mobile stations or between
a mobile station and the GI interface to an external packet data network.
This includes all delays within the GPRS network, e.g., the delay for request and assignment of radio
resources and the transit delay in the GPRS backbone network. Transfer delays outside the GPRS network,
e.g., in external transit networks, are not taken into account.

Throughput
The throughput specifies the maximum/peak bit rate and the mean bit rate.
Using these QoS classes, QoS profiles can be negotiated between the mobile user and the network for each
session, depending on the QoS demand and the available resources.
The billing of the service is then based on the transmitted data volume, the type of service, and the chosen
QoS profile.
 • cJtVt~ -;b5 be
ueJcN"6'fI ~ Afl"fS. ll~) ~~ ~olrf"'e
O\q<w, l.J1'-1/... AMI'S,
,/7
D-AMPS (Digital Advanced Mobile Phone System) _~~U\~'01'\)
. ~-e ~4-~
Digital Advanced Mobile Phone System (D-AMPS) is a digital version of Advanced Mobile Phone Systems
(AMPS), the original analog standard for cellular phones. D-AMPS uses a combination of time division
;;'ultiple access (TOMA) and frequency division multiple access (FOMA). It adds TOM A to get three
channels per AMPS channel, thus tripling the number of calls on a channel.
Features
• They are standardised by IS-54 and IS-136.
• As in AMPS, O-AMPS also uses frequencies from 800 to 900MHz for transmission. Half of the
~ectrum is used for sending signals and the other half is used for receiving signals.
• ~he frequency band is divided into 30KHz sub-bands, called channels, by FDMA.
• The channels for uplink are called forward channels and the s hannels for downlink are called reverse
. channe ls .
• !DMA is applied to each channel thus tripling the number of available channels.
• Presently, all O-AMPS channels are replaced by GSM or COMA technology.
..
• It is an analog system and is based upon initial electromagnetic spectrum allocation for cellular
service by the federal communication commission.
• It uses FDMA (frequency division multiple) access for multiple simultaneous conversations.
• :Vhen the number of conversations is very high, it requires high bandwidth.
• It was the first to use hexagonal cells.
• Cells inA MPS are 10 km to 20 km across.
• Since it was analog technology, it suffers from noise and eavesdropping.
AMPS (Advanced Mobile Phone System) was invented by Bell Labs and first installed in the United
States in 1982. In all mobile phone systems, a geographic region divides up into cells, which is why the
devices .are sometimes called cell phones.
In AMPS, cells are smaller and typically 10 to 20 km across digital systems. Each cell uses some set of
frequencies, which are not used by any neighbors. The key idea that gives cellular systems far more capacity
than previous systems is the use of relatively small cells and the reuse of transmission frequencies in nearby
cells. Thus, the cellular design increases the system capacity by at least some order of magnitude. Smaller
cells mean that less power is needed, which leads to smaller and cheaper transmitters and handsets.

Working of AMPS:
In an area where the number of users has grown to a point, where the system is overloaded, the power can
be reduced and the overloaded cells split into small micro-cells to permit more frequency reuse. At the
center of each cell , there is a base station to which all telephones in the cell transmit.
The base station consists of a computer and transmitter/receiver connected to the antenna. In a small system ,
all the base stations are connected to a single device called MSC (Mobile Switching Center) or
MTSO(Mobile Telephone Switching Office).
The MSCs are essential for ending offices, as in telephonic systems, and are in fact connected to at least one
telephone system ' s end office.
At any instant mobile phone is logically in one specified cell and under the control of that cell ' s base station.
The mobile phone is then informed of its new boss (when the user leaves the current cell) and if a call is in
progress, it is asked to switch to a new channel.
This process is called handoff, which takes about 300 msec. Channel assignment is done by the MSC, the
nerve center of the system.

...~ · .:;...;c r a

:e S
_ _ _ d';.
" I .•

~,-(~~
criJ/i.. dill.. ~£.
~r..ge.~'

AMPS (Advanced Mobile Phone System):

Advanced mobile phone system (AMPS) was a standard for analog cellular phone system developed by Bell
tabs and officially introduced by AT&T in 1983. It was officially introduced in the Americas on Oc~ober 13,
1983,lsrael in 1986, Australia in 1987, Singapore in 1988, and Pakistan in 1990.
AMPS is a first-generation cellular technology that uses separate frequencies or "channels", for each
conversation. It therefore required considerable bandwidth for a large number of users. In general terms,
AMPS was very similar to the older "OG" Improved Mobile Telephone Service, but used considerably more
computing power to select frequencies, hand off conversations to PSTN lines, and handle billing and call
setup.
What really separated AMPS from older systems is the "back end" call setup functionality. In AMPS, the
cell centres cou Id flexibly assign channels to handsets based on signal strength, allowing the same frequency
to be re-used in various locations without interference. This allowed a larger number of phones to be
supported over a geographical area.

Features
• It is an Analog system based on the initial electromagnetic spectrum allocation for cellular service
by the Federal Communications Commission.
• It lIses frequency division multiple access (FDMA) for multiple simultaneous conversations.
• <Frequency ranges within the 800 and 900 MHz are allocated for cellular telephones in AMPS.
~

Half of the signal is used for sending signals and half is used for receiving signals.
• !t has a high bandwidth requirement particularly when the number of conversations is very high.
.
• It was the first system to use hexagonal cells. So, the pioneers of AMPS had coined the term
..coined cellular.­
• The cells in AMPS are 10km to 20 km across.
• ~F bandwidth 30khz. The band can accommodate 832 duplex Channels, among which 21 are
reserved for call set up, and the rest for voice communication.
 • Frequency allocated by · FCC(FederaJ Communications Commission) on 824-849MHz fpr
.
downlink and 869-894MHz for Uplink traffic .
'

• Since, it was an Analog technology, it suffered from noise and Eavesdropping

(Eavesdropping is as an electronic attack where digital communications are intercepted by an individual
v010m they are not intended. This is done in two main ways: Directly listening to digital or analog voice
communication or the interception or sniffing of data relating to any form of communication.)
,
High powered base
,tation to which all
users connect .­ /
~ -~===::
I
Wired
connection to
telephone
network

HexaBonal Ce lis

coverage areas

- - - - - - - -- - - - -- - - '
The analog service of AMPS has been updated with digital cellular service by adding to FDMA a further
subdivision of each channel using time division multiple access (TDMA). This service is known as digital
AMPS (D-AMPS)
AMPS and D-AMPS have now been phased out in favour of either CDMA2000 or GSM, which allow for
higher capacity data transfers for .services such as WAP, Multimedia Messaging System (MMS), and
wireless Internet access. There are some phones capable of SUppol1ing AMPS, D-AMPS and GSM all in one
phone (using the GAIT standard).

AMPS System Components:

t I. Public Switch Telephone Network (PSTN)
2. Mobile Telephone Switching Office (MTSO)
3. Cell site with Antenna
4. Mobile Subscriber Unit
 - 1!0UNCM't' CF ., c.EU. CUJST'ER
. _ - CE..1... !rT£ T'R.N(S & OIlTA I.NtS

CELL. SITE
c:aJ..S WITH THE SAllE M.a.R
OSE 'Tl€ SAle ~ atANNIU
How Advanced Mobile Phone Service works:
The First AMPS cellular system used large cells and omni directional base station antennas to minimize the
Initial equipment needs. The AMPS system Uses a seven-cell reuse pattern with provisions for sectorin~d
cell splitting to increase capacity when needed .
AMPS was designed as a voice only System.
AMPS use frequencies in the 800-MHz to 900-MHz range of the radio spectrum. It modulates a 3-kHz
voice channel onto 30-kHz FM carrier signals using Frequency Division Multiple Access (FDMA) to create
a series of 30-kHz channels. Separate channels are used for base station to mobile transmission (forward
channels) and mobile station to base transmission (backward channels). The resulting allocation of
bandwidth for each channel results in a maximum of approximately 800 simultaneous phone conversations
per operator.
Because the population of most cities would suggest that 800 simultaneous phone conversations is far from
enough, the idea was developed to partition the coverage of cities into several small areas called "cells."
Each base station uses a limited-power transmitter with a directional antenna to provide coverage for a
;mall geographical cell (from which the term "cellular communication" arose) . A typical cell ranges
from .5 kilometre to 20 kilometres in size. depending on 'vvhether the coverage i s in a densel 0 ulated
urban area or a sparsely populated rural one. Mobile users' phones a so ave limited transmission power,
~ eaning that communication is usually limited to the immedIate cell the user is in. As a user moves from
one cell to another, the signal is smoothly picked up from the new cell. Adjacent cells use dIfferent
frequencies, which prevents interference.
In communication with the network the mobile provides two identifiers for registration, call control and
'"
validation. The first of these identifiers is the MOBILE IDENTIFICATION NUMBER (MfN), which is
programmed handset phone number used to call the subscriber.
the second IdentIfIer IS the ELEe I RUNIC SERIAL NUMBER (ESN), which is a manufactured
cFlaracteristic of the mobile unit. This identifier is permanent and associated with the physical equipment...!.!
is 32bits is length, with the first 8 bits identifying the manufacturer.

CDMAONE (~~) I ,q<?¥"" ~.M-~~~~~

..tA fV'A--eJ rt.lqo· ,.r~qr .k G~~:J!ru1
IS-95. cdmaOne was the first cellular standard to implement the COMA multiple access scheme. also (!.,4f'\A
known as IS-95. Individual channels can be distinguished from one another by means of unique orthogonal - ~i.
codes. \:yithin this standard, all services - including speech and data - are circuit-switched with a maximum
i!ata rate of either 9.6 kbit/s or 14.4 kbit/s on each channel. With the IS -95-B technology extension, many
operators also offer 64 kbit/s packet-switched data, in addition to voice services. A bandwidth of 1.25 MHz
results in up to 61 channels under optimal channel conditions. cdmaOne is included as a subset in all
cdma2000® standards up to the latest IxEV-OO Rev. B standard.
COMA is an American Standard that was developed by Qualcomm .
It was originally developed for the battlefield because it is very hard if not impossible to intercept due to
their spread spectrum natyre.:.
~DMA is now defined by a number of standards, some of which are IS-95 , J-STO-008 (PCS) and COMA
2000.

A unique code is assigned to all digital speech bits and the signals spread across the broad spectrum of the
RF . Each COMA base station can use the same 1.25 MHz cgp:iet at the same time.
Ther~ are a maximum of 64 Walsh noise codes per 1.25MHz in a COMAOne sy~~.
COMA networks have pilot channels which carry no dat~ but are used by the subscriber's mobile unit to
acquire the system and assist in the soft handoff process. A separate pilot channel is transmitted for each
sector ofa cell site and is uniquely identified by it's own PN code, just like other users

COMA refers collectively to three COMA standards that were the first formal specifications assigned to the
J 4~· q ~- ~ 1).\~ ~ .{ ~~ t1 ;:Q, gq ~ f'Ji. ~ • 4-- 3 G
t'1
technology; Q G,
I . IS-95A ( .~t 1\ (I~..(\) ~ .qq \) f-.A,¥."t-J
2.IS-95B
3. J-STO-008 1J.fo~"It..lR.~I\tVo(.v) Lt:"J:!
(P~)
w
G..tM
r~t.
~
~a\(-~'1~M(~ ~~'\-~'l~ p.\i'2., • ~~, ~ 1'~ -q\~
(~~<.:l-I~l '0 ~fi (93~ .... l Ho MH'2- • U~'.s.. . CIlf\'\A~'C<!o
c; OMAOne sta~ dards have evolved in the complexity and..dfectiveness. Earlier versions (IS-95A&ID had
issues with voice quality, data throughput and were limited in the methods in which they transmitted data.
~~~~~~~~~~~~~~~~~~~~~~~--
-- Tao, - A-IV ~.1, p..1M.IJ 7Acs.. ,j'J-A..cs ) e-}J~~
JI G, - G,,tf\,,,""\' {VI P.s. ,)'..f-9,(" ~ G-.- ~- ~fO (flU
1iJ <;'!!!- U M1"'S , C4~ MA ~ o~ IJ , i Jl-.te. D 1-" A

11 (h - Lr.fV\.j, 1V<.M ~~~ {L7r'

IS-95B and J-STO-008 allowed for Integrated Service Digital Network or ISDN to be used. More advanced
call ing features were accessible COMA 2000 falls under the specification known as IS-2000 as is backward
compatible with earlier versions. COMA2000 is a 3G specification, which allows for multidata platform
usage.

2G

2.5G
~\IV\
~~'~';c~~,
. L - - - - - - ----i

~#a-
lU~b;,~
~_~$ 3G
~~~
O-~)
Interim Standard 95 (IS-95)
..... ~~~~
-Also known as cdmaOne f'cYJ:~Wu.'jJ
-64 users in a 1.25 MHz channel. ~'~q
-Can be used in 800 MHz and 1900 MHz bands.
EVDe1-G~-~ ~~'wJ.ul
-Sprint and Verizon in the U.S. Ad.uiAJl.. CJ.{R~A 4
-Spectrum bandwidth: AVJ\IY\' flit 8, ~
-1850 to 1910 MHz Mobile to Base
-1930 to 1990 MHz Base to Mobile • c:l3fv1,A 0<1) {) a, UA~
-Channels are 1.25 MHz ...w.~/c.o~ ~
-3.75 MHz in COMA 2000, 5 MHZ in UMTS No¥:i1. A-M(l>cJ.'e&-­
-Results in approximately only 48 forward/reverse channel pairs in IS-95. • c: I.lflAJo1a.oc>o ...u. ().. cJ,1J
-Adjacent cell phone towers.use the exact same channels as all other towers. ~J~~ . ~
-This is a major difference. .tlL~~ :t., 1 Jr. q ;:
-Allows for much better frequency reuse and makes setting up a cellular network much easier. If

• S40..~ - :M p.{ J.v..qjUJ ~5)~

Upgrade path from IS-95A to IS-95B for 2.5G COMA ~Ik ~c1AJ ~"(1'10'0..
-Only one upgrade path for IS-95 - 'i'~ (I x:.,(iT) , fr.~
-Users can use up to 8 COMA codes simultaneously. ~ 4'.HI\1A~ 1<.A..1.~e.. <3,
-14.4 kpbs* 8 = 115.2 kbps ~UQ-1:l ~.w-1I'f-...~ A ~
-Practical throughput is 64 kbps that can actually be achieved. lI.
L£"U~() ~b.JIP-
-.Also changes the method of handoff between base stations. l r-v
• 00J:a M.tI.l- ~o-MV\ ~tl 0 t) . ~:l)c
{I.);,~~ ~- ;M u/).~ ~rd~ f NYv-~ rbJo ~ uJrlo
c;,
..

~~~ (J~e ~u.f,,~ k~ -lIs Mh~s M ~,,~ ~

II. _ . _ {- ~ ~ ~ v.A~ 8 'P.s+< ~ M
1.1_ . 1J.'f;.ta..
~ o4Jo. ~ I~& fA-h",.r ....."..P-'<'- v..yv
(~ d)AAM ~ N~ . ~~
~cJ1;I.. U lAAetJ 0- ~
• ~ we";'''' J ~ ,.,,-, 1"'\-Iz.';'~Mf. (pnD,
• M~~:r~ ~ ~~ I!'~'~:-Ilr-. ~
~~ ~'t?/dJ .wu- 1V~-
hdM
I
 'Um' 'Abis' 'A' 'Ai'

TermInal

N(lhvork IlltN'COllll(lCtS
• Airlillk: "UlU" Interface
• BTS-to-BSC: '''A'' Base Station Intelface (bis)
• BSC-to-MSC: "A" Interface
• ~fSC -to-1rlSC: "Ai" Interface

Pa~ket Data System

Packet Data Systems was formed in 1991 to supply European telecommunication test products to a market
dominated by high value American products. The capabilities of the European products were identical and
in some cases better but the cost was much lower so the market responded with great enthusiasm.
The most powerful product we had was our Clarinet protocol test system comprising of a range of
physical interfaces which connect to a laptop PC host running an application to simulate many telecom
protocols including DASS2, DPNSS, ISDN, Q-SIG, V5.1, V5.2, SS#7, H.323, SIP and SIPi which were
used by all the major telecom operators, the government, ministry of defence and many companies
manufacturing and testing PBX or Switch harware. Many thousands of Clarinet systems have been sold
with full support and product training offered by PDS internationally.
PDS also soon became a manuafacturer of our own range of ISDN network simulators which could be
used to demonstrate two ISDN basic rate video conferencing terminals, two ISDN telephones or two ISDN
data terminals working back-to-back. You can find information leaflets for our B-Link unit which had two
ISDN basic rate S-T or 2B IQ U interfaces, and our Simline 6 which has six ISDN basic rate S-T interfaces
and one optional ISDN primary rate E I interface on this web page and they can sometimes be purchsed on
eBay . These became very popular and we were asked by the government to build products based on our
design to fill more complex applications resulting in the sale of hundreds of these products allover the
world.
In 2015 a number of companies got together and decided to share the development of their own products in
order to avoid spending too much money. One of the first products they produced was
called Wireshark which is an excellent protocol analyser but when they finished, they decided to put it on
to the internet and let anyone download it free-of-charge so the market was destroyed damaging PDS and
many of our competitors.
We still had protocol simulators to sell but fewer people were using this approach , and soon another product
called SIPp was released. SIPp is a protocol simulator for the session initiation protocol and this too was
put on to the internet free-of-charge. The only prodcuts we had left now were Protocol Conformance
Testers which could be used to automatically generate messages to all connected devices and check their
responses, a correct responce would result in a 'PASS' verdict and a wrong response would result in
a 'FAIL' verdict. These systems offered a perfect way to point fingers at devices which were not in full
compliance of the protocol but were very expensive so therefore the market was too small.

II ~,J~<G crtr ~ IV' A .Q~ () ~-

.~e .
. ~~ 9~6 .. ~ urrw-.-e&.c'(}'fb
.. ~(J-dst..t'~
. . L" .. .-rI W (VI.,A !.t \) 0 0­
& 01~~~~ ur
""""f~~ ~ ~ carv­
. r~ u1r ~ ~ ct V'1J1~ /t&Ie.

,,~~ ~cJ,..~'~ ~Er~~-J--

• J~'~ ~-;~ 1'1 s. ~ t. ~(!,

,. J' 4 JQ.i<-A(V.' ~

• Ct1MA.Q~(!)~ ~-
• ,A1 - -rc..U ( r 1'3 , tJ\fP::2. , MTf I I~'"
I ,,".. ~~,(c9
.. A~ - T('P,Y ,A-At...r, ~S:~AA /AAL.tJ. .
• A7 - ,e 1/ ~ I Ar-r SA~51"~'~ , IV1L..r
~t\g- fPPJr;J.J <St.AE'

• ,A-q - T<!(J I U v.J P, 'r-P ·-A q ~~c

AAfo -:Df', Gt/J..G-Jppp
. AIr - /<AtI-!5"1'lA 1JfJ ) T' f fJ , ut) ~ ) VI ),Au ~~~J.n~s
• J4/~ - 2P _ ~ PfJ, fd4IJ!lv!
.. Ii 13 - TC!..P / v typ ,:2/, A q ~gv..rJ..#d
.,4(Y- tI ,-4,,/Att.{ lA

, fits'" - l{ J " , Af~ {f