Machine Translated by Google

Support PD input fully integrated 5W/7.5W/10W/15W wireless charging transmitter SOC

IP6829 Featuresÿ Compatible

with WPC v1.2.4 and v1.3 standardsÿ Support 5~15W

IP6829 Overview
multiple applicationsÿ Single 5W applicationÿ
IP6829 is a wireless charging transmitter control SoC chip.
Fast charging charger input

Compatible with the latest WPC Qi v1.3 standard, supporting A11, A11a,
5~15W application5V input 5W application; 9V input

5W, 7.5W, 10W application;

MP-A2 coil, supports 5W, Apple 7.5W, Samsung 10W,
12V input 5W , 7.5W, 10W, 15W application.ÿ 12V

charger input 15W applicationÿ Support multi-coil solution (two 15W charging. IP6829 detects wireless access via analog ping

coils, three coils)

The receiver establishes communication with the receiving end, then the power

Transmission. The IP6829 decodes the communication data packets sent from the receiver,
ÿIntegrated NMOS full-bridge driver and full-bridge power MOS

ÿIntegrated internal voltage & current dual-channel

Then use the PID algorithm to change the oscillation frequency to adjust the coil
demodulation ÿSupport FOD foreign object detection function
output power.
ÿ Highly sensitive static foreign object detection (adjustable by capacitor) ÿ

Support dynamic FOD detection ÿ

IP6829 integrates full-bridge drive circuit and full-bridge power

External resistor to adjust FOD parameters (adjust dynamic FOD)

MOS, voltage & current two-way ASK communication demodulation module; solution
ÿLow static power consumption and high

efficiencyÿQuiescent current The high level of integration can significantly reduce solution size and BOM cost.

10mA ÿMeasured system charging efficiency up to 80%

ChipSourceTek
ÿCompatible with NPO capacitors and CBB capacitors

ÿDynamic power adjustment for USB power supply with insufficient power supply capacity

Function (DPM) ÿ

Supports chargers as low as 5V 500mA

ÿInput overvoltage, overcurrent, undervoltage protection

IP6829 application products ÿ

Back clip, wireless charging base

ÿ Car wireless charging equipment

functionÿSupport repeated firmware

upgradeÿSupport PD3.0 input

requestÿSupport DPDM fast charge input

requestÿSupport Qi protocol BPP , PPDE

certificationÿSupport NTC

overtemperature protectionÿSupport up to 3 LED

indicationsÿPackage 5 mm × 5 mm 0.5pitch QFN32

TEL: +86-0755-27595155 27595165 FAX:

+86-0755-27594792 WEB:Http:// 1 / 17 Version 1.0
www.ChipSourceTek.com E-mail:
[email protected] [email protected]
Machine Translated by Google

Support PD input fully integrated 5W/7.5W/10W/15W wireless charging transmitter SOC

IP6829 system block diagram

ChipSourceTek
Figure 1 System Block Diagram

TEL: +86-0755-27595155 27595165 FAX:

+86-0755-27594792 WEB:Http:// 2 / 17
www.ChipSourceTek.com E-mail:
[email protected] [email protected]
Machine Translated by Google

Support PD input fully integrated 5W/7.5W/10W/15W wireless charging transmitter SOC

1. IP6829 pin definition

Figure 2 IP6829 pin diagram

ChipSourceTek
Pin No. Pin Name

1 GND Analog Ground

IP6829 Pin Description

describe

2 IGND Current communication/demodulation negative input

3 INSANE Current communication/demodulation positive input

4 VCC Internal VCC power supply, output connected to 2.2uF capacitor to ground

5 PGND The power ground of the internal power MOS tube is connected to the positive end of the external 20 milliohm sampling resistor

6 HOSCI External crystal oscillator input

7 HOSCO external crystal oscillator output terminal

8 CC1 Type_C detection pin CC1

9 CC2 Type_C detection pin CC2

10 DEBUG Debug pin

11 NTC NTC Detection PIN

12 LOSS_THR Dynamic FOD parameter adjustment, external resistor to GND adjustment

13 LED1 LED1 Output

14 IO4 Internal GPIO4

15 LED3 LED3 Output

16 LED2 LED2 Output

TEL: +86-0755-27595155 27595165

FAX: +86-0755-27594792 3 / 17
WEB:Http://www.ChipSourceTek.com
Email: [email protected] [email protected]
Machine Translated by Google

Support PD input fully integrated 5W/7.5W/10W/15W wireless charging transmitter SOC

17 IO7 Internal GPIO7

18 V_DECODE Voltage communication/demodulation input

19 BST1 Internal high voltage driver, connect capacitor to LX1

20 LX1 H-bridge switch node 1

21 LX1 H-bridge switch node 1

22 LX2 H-bridge switch node 2

23 LX2 H-bridge switch node 2

24 BST2 Internal high voltage driver, connect capacitor to LX2

25 NC NC PIN is suspended and cannot be grounded

26 COME External voltage input PIN

27 COME External voltage input PIN

28 DM USB DM

29 DP USB DP

30 VDET Voltage detection input

31 NC NC PIN is suspended and cannot be grounded

32 AGND Analog Ground

ChipSourceTek
33

2. IP6829 limit parameters

EPAD (PGND) The power of the internal power MOS tube is low, connected to the positive end of the external 20 milliohm sampling resistor

parameter symbol Minimum Maximum Unit

COME -0.3 16

Input voltage range CC1, CC2 -0.3 12 V

DP, DM -0.3 8

Junction temperature range TJ -40 125 ÿ

Storage temperature range Tstg -60 125 ÿ

Thermal resistance (junction to ambient) ÿJA 40 ÿ/W

Human Body Model (HBM) ESD 4KV V

* Stresses above those listed under the Absolute Maximum Ratings section may cause permanent damage to the device.

Excessive exposure time may affect the reliability and service life of the device

3. IP6829 recommended working conditions

parameter symbol Min Typ Max Unit

VIN Input Voltage Range COME 4.5 5/9 12 V

LED1,LED2,LED3 GND-0.3 VCC+0.3

I/O voltage range V

NTC,LOSS_THR GND-0.3 VCC+0.3

TEL: +86-0755-27595155 27595165

FAX: +86-0755-27594792 4 / 17
WEB:Http://www.ChipSourceTek.com
Email: [email protected] [email protected]
Machine Translated by Google

Support PD input fully integrated 5W/7.5W/10W/15W wireless charging transmitter SOC

IO4,IO7 GND-0.3 VCC+0.3

DP, DM,CC1,CC2 GND-0.3 5.5

*Device operational characteristics are not guaranteed outside these operating conditions.

4. IP6829 electrical characteristics

Unless otherwise specified, TA = 25°C

parameter symbol Min. Typ. Max. Unit Detailed description/Test conditions

COME 4.5 5/9 12 V

VCC 3.8 4.2 5 V

HIV Input high level 0.7xVCC V

WILL Input low level 0.3xVCC V

VOH Output high level VCC V

VOL Output low level GND V

Source LED1ÿLED2ÿLED3 Source current to output high voltage

2 4 mA
current Output current capability Level is 0.8xVCC

ChipSourceTek
Rds Driver bridge MOS tube impedance 25 mÿ

5. IP6829 Function Description

PD fast charge input request

Built-in PD protocol input request module, apply for fast charging voltage from PD adapter through CC1 and CC2.

Full-bridge driver and power MOS

IP6829 has two built-in symmetrical half-bridge driver modules and built-in power MOS.

TEL: +86-0755-27595155 27595165

FAX: +86-0755-27594792 5 / 17
WEB:Http://www.ChipSourceTek.com
Email: [email protected] [email protected]
Machine Translated by Google

Support PD input fully integrated 5W/7.5W/10W/15W wireless charging transmitter SOC

ChipSourceTek Figure 3 Full-bridge driver application circuit

DPM

For USB power supplies with insufficient power supply capacity, it has a dynamic power management function to keep the charging state uninterrupted. When the system detects that the input

voltage is lower than 4.3V, the DPM function is activated to reduce the transmission power and maintain it. When the input voltage returns to above 4.75V and the input current is reduced by 200mA

compared to when entering DPM, the system exits the DPM state.

Digital Demodulation

Built-in two-way ASK demodulation module, can collect coil voltage and current for ASK communication demodulation and decoding.

The signal is acquired through the impedance and sent to the chip for digital demodulation and decoding.

TEL: +86-0755-27595155 27595165 FAX:

+86-0755-27594792 WEB:Http:// 6 / 17
www.ChipSourceTek.com E-mail:
[email protected] [email protected]
Machine Translated by Google

Support PD input fully integrated 5W/7.5W/10W/15W wireless charging transmitter SOC

Figure 4 Voltage ASK voltage demodulation peripheral circuit

ChipSourceTek
Figure 5 Current ASK Current demodulation peripheral circuit

FOD parameter adjustment

IP6829 supports static FOD foreign object detection and dynamic FOD foreign object detection;

Static FOD means that foreign objects on the coil can be detected when there is no wireless charging; Dynamic

FOD means that foreign objects on the coil can be detected when wireless charging is in progress;

IP6829 can adjust the sensitivity of static FOD by adjusting the capacitance on the V_DET pin; by default, a 2.2nF capacitor is connected to ground.

Standard static FOD sensitivity; the larger the connected capacitance, the higher the sensitivity of the static FOD, and the easier it is to detect foreign objects;

TEL: +86-0755-27595155 27595165 FAX:

+86-0755-27594792 WEB:Http:// 7 / 17
www.ChipSourceTek.com E-mail:
[email protected] [email protected]
Machine Translated by Google

Support PD input fully integrated 5W/7.5W/10W/15W wireless charging transmitter SOC

IP6829 can adjust the sensitivity of dynamic FOD by connecting an external resistor from the LOSS_THR pin to GND. By default, the LOSS_THR pin is connected to a

100K resistor to ground, using the standard dynamic FOD sensitivity. The larger the external resistor R_Loss of LOSS_THR , the lower the sensitivity of dynamic FOD, and the

more difficult it is to detect FOD. The sensitivity of dynamic FOD is set by only detecting the resistance of the LOSS_THR pin at power-on. 50K<R_LOSS resistance<130K.

ChipSourceTek

NTC thermal protection

The NTC pin of IP6829 outputs a fixed current of 20uA. The NTC PIN determines the NTC temperature by sampling the voltage of the NTC pin. This shutdown feature

provides enhanced applications, not limited to thermal shutdown. When the voltage of the NTC pin is less than 0.5V, the system will enter the NTC protection state and end power

transmission. After entering the NTC protection, the NTC pin voltage is greater than 0.72V, and normal charging will resume. If the NTC application is not used, the pin is grounded

through a 100K resistor. 1.

Refer to the NTC resistor data sheet to find the resistance-temperature relationship

table 2. Find the corresponding resistance value R_NTC according to the

protection temperature point 3. Determine the series resistance R_SetPoint1 and the parallel resistance

R_SetPoint2 according to the following formula If the temperature protection point needs to be increased: parallel resistance R_SetPoint2 NC, change the

series resistance R_SetPoint1=25K-RNTC; If the temperature protection point needs to be reduced: series resistance R_SetPoint1=0 ohm, parallel resistance R_SetPoint2=25K*RNTC/(RNTC-2

TEL: +86-0755-27595155 27595165 FAX:

+86-0755-27594792 WEB:Http:// 8 / 17
www.ChipSourceTek.com E-mail:
[email protected] [email protected]
Machine Translated by Google

Support PD input fully integrated 5W/7.5W/10W/15W wireless charging transmitter SOC

The recommended resistors for the protection temperature of 60 degrees are as follows: RNTC=100K@25 degrees B=3950, R _ Setpoint1=0 ohm, R _ Setpoint2 NC;

The recommended resistors for the protection temperature of 70 degrees are as follows: RNTC=100K@25 degrees B=3950, R _ Setpoint1=7.5K ohms, R _ Setpoint2 NC;

The recommended resistors for the protection temperature of 50 degrees are as follows: RNTC=100K@25 degrees B=3950, R _ Setpoint1=0 ohm, R _ Setpoint2=82K ohm.

LED Status Indicator

ChipSourceTek
IP6829 can directly drive 2 LED outputs through series current limiting resistors. The corresponding relationship between the two LED states and the system state is as follows:

Status

Power
LED1

Flashes 3 times simultaneously

LED2

on Off Destroy

Standby Steady Destroy

Charging Abnormal on Off Flash

By customizing or modifying the firmware with configuration tools, up to 3 LEDs can be supported, including breathing (LED1), flashing, always on, always off, and PWM adjustment.

brightness.

Efficiency curve

When using the IDT P9221_R receiver, the relationship between efficiency and system output power is shown in the following figure.

TEL: +86-0755-27595155 27595165

FAX: +86-0755-27594792 9 / 17
WEB:Http://www.ChipSourceTek.com
Email: [email protected] [email protected]
Machine Translated by Google

Support PD input fully integrated 5W/7.5W/10W/15W wireless charging transmitter SOC

Vout=5V

ChipSourceTek
Figure 6 System efficiency (using IDT P9221_R RX)
Vout=9V

Figure 7 System efficiency (using IDT P9221_R RX)

TEL: +86-0755-27595155 27595165 FAX:

+86-0755-27594792 WEB:Http:// 10 / 17
www.ChipSourceTek.com E-mail:
[email protected] [email protected]
Machine Translated by Google

Support PD input fully integrated 5W/7.5W/10W/15W wireless charging transmitter SOC

Vout=12V

Figure 8 System efficiency (using IDT P9221_R RX)

ChipSourceTek
6. IP6829 Application Instructions

IP6829 can realize wireless charging solutions of different powers by matching different transmitting coils and resonant

capacitors. According to customer needs, 10uH coil with 250nF resonant capacitor, 6.3uH coil with 400nF resonant capacitor can be customized.

7. IP6829 firmware upgrade instructions

IP6829 can repeatedly burn firmware, and needs to use the matching upgrade tool to upgrade.

8. IP6829 Typical Application Schematic Diagram

IP6829 only requires a small number of passive components such as capacitors and resistors to achieve a fully functional wireless charging solution.

BST1, BST2 boost capacitors C6, C8 cannot be omitted

TEL: +86-0755-27595155 27595165 FAX:

+86-0755-27594792 WEB:Http:// 11 / 17
www.ChipSourceTek.com E-mail:
[email protected] [email protected]
Machine Translated by Google

Support PD input fully integrated 5W/7.5W/10W/15W wireless charging transmitter SOC

ChipSourceTek

TEL: +86-0755-27595155 27595165 FAX:

+86-0755-27594792 WEB:Http:// 12 / 17
www.ChipSourceTek.com E-mail:
[email protected] [email protected]
Machine Translated by Google

Support PD input fully integrated 5W/7.5W/10W/15W wireless charging transmitter SOC

BOM
Number Component Name Packaging & Specifications Position No. Dosage

1 LED LED2, LED1 LED0805 2

2 IN5819 D1 SOD-523_L1.2-W0.8-LS1.6-RD CAP- 1

3 250nF C1-C4 TH_L13.0-W7.5-P10.00-D1.0 1

4 15nF C10, C11, C12 C0603 3

5 2.2nF C5 C0603 1

6 100nF C4,C6,C8 C0603 3

7 2.2uF C7 C0603 1

8 IP6829 U1 QFN-32_L5.0-W5.0-P0.50-BL-EP3.4 1

9 100kÿ RNTC R0603 1

10 10uH L1 IND-SMD_L2.5-W2.0 1

11 33k R25 R0603 1

12 3.3k R22 R0603 1

13 100k R20,R27 R0603 2

14 1k R24,R23 R0603 2

15 10k R21 R0603 1

ChipSourceTek
16 10uF C1 C0805 1

17 22uF C2, C3 C0805 2

18 20mR R16 R0603 1

19 TYPE-C-31-M-12 USBC1 USB-C_SMD-TYPE-C-31-M-12 1

TEL: +86-0755-27595155 27595165

FAX: +86-0755-27594792 13 / 17
WEB:Http://www.ChipSourceTek.com
Email: [email protected] [email protected]
Machine Translated by Google

Support PD input fully integrated 5W/7.5W/10W/15W wireless charging transmitter SOC

9. IP6829 Layout Notes

1. As shown in the figure below: the current sampling resistor and the PGND of IP6829 are power traces. The traces need to be as short as possible and more vias need to be added when changing layers.

ChipSourceTek
2. As shown in the figure below: Input the filter capacitor between VIN and PGND. The closer the loop area, the better.

3. The capacitor of pin 4 VCC should have a sufficient capacity of 2.2uF and be located close to the chip pin; and the VCC capacitor should be connected to the chip 1

The ground loop of the pin cannot be blocked by other signals.

4. As shown in the figure below: The sampling line between the current sampling resistor and IP6829 ISENSE and IGND needs to be led from both ends of the resistor separately and not be connected to the same

The power lines of the network overlap and are as short as possible, while being away from resonant capacitors and coils.

TEL: +86-0755-27595155 27595165 FAX:

+86-0755-27594792 WEB:Http:// 14 / 17
www.ChipSourceTek.com E-mail:
[email protected] [email protected]
Machine Translated by Google

Support PD input fully integrated 5W/7.5W/10W/15W wireless charging transmitter SOC

5. As shown in the figure below: The V_DECODE and V_DET wiring of IP6829 should be kept away from the resonant capacitor, coil and other power wiring as much as possible.

To package the land for processing;

ChipSourceTek

6. The loop area between the resonant capacitor, coil and IP6829 should be as small as possible and should be kept away from low voltage signal paths such as LED, NTC, IO, etc.

Wire.

TEL: +86-0755-27595155 27595165 FAX:

+86-0755-27594792 WEB:Http:// 15 / 17
www.ChipSourceTek.com E-mail:
[email protected] [email protected]
Machine Translated by Google

Support PD input fully integrated 5W/7.5W/10W/15W wireless charging transmitter SOC

10.IP6829 packaging information

ChipSourceTek

TEL: +86-0755-27595155 27595165 FAX:

+86-0755-27594792 WEB:Http:// 16 / 17
www.ChipSourceTek.com E-mail:
[email protected] [email protected]
Machine Translated by Google

11. Liability and Copyright Statement

Silicon Source Technology Co., Ltd. reserves the right to make corrections, modifications, enhancements, improvements or other changes to the products and services provided.

Before placing an order, you should obtain the latest relevant information and verify that the information is complete and up to date. All products are sold subject to the order confirmation.

Terms and conditions of sale provided.

Silicon Source Technology Co., Ltd. assumes no obligation for application assistance or customer product design. Customers should assume all liability for their use of Silicon Source products and applications.

To minimize the risks associated with customer products and applications, customers should provide adequate design and operational safety verification.

Customers acknowledge and agree that, although any application-related information or support may be provided by Silicon Source, they will be solely responsible for satisfying their product

Customers declare and agree that they have the ability to formulate

All the expertise and knowledge required to implement safety measures, including foreseeing the dangerous consequences of failures, monitoring failures and their consequences, and reducing the risk of

The customer will fully indemnify the customer for any damages resulting from the use of any silicon source in such critical applications.

any losses caused to Siyuante and its agents due to the use of Siyuante products.

For Silicon Source's product manuals or data sheets, only if the content is not tampered with and with the relevant authorizations, conditions, restrictions and statements

Copying is permitted only if the information provided by the Company is not altered. Silicon Source assumes no responsibility or liability for such altered documents. Copying third party information may require

ChipSourceTek
Additional restrictions apply.

Silicon Source will update the contents of this document from time to time. The actual parameters of the product may vary due to different models or other factors. This document does not make any

for any express or implied warranty or warranty.

When reselling a Silicon Source product, if the statement of the product parameters is different from or false to the parameters indicated by Silicon Source, it will be

You will lose all express or implied warranties regarding the relevant Silicon Source products and this is an unfair and fraudulent business practice. Silicon Source will not be responsible for any such false

No liability or responsibility is assumed for any statement.

TEL: +86-0755-27595155 27595165 FAX:

+86-0755-27594792 WEB:Http:// 17 / 17
www.ChipSourceTek.com E-mail:
[email protected] [email protected]