International Standard Valve, Inc.

7111 Perimeter Park Drive, Bldg 320

Houston, Texas 77041
713-983-7600

Two Piece Trunnion Mounted

Ball Valve

ASME
CLASS
150
through
1500

WCB
LCC
CF8M
Body

API 6D
Fire Safe
NACE
CE

is a registered trademark of International Standard Valve, Inc.

www.isvalve.com [email protected] Bulletin No. ISV-SB210.6 Issue 02/2011
 Specifying ISV Series No. BT3BF 2 PC trunnion ball valves
Example: ISV figure number BT3B-F060-1210RF-DH-NFG
Describes an ASME class 600, two piece bolted body design, full port, trunnion supported ball valve, raised face flange ends, with WCB body material, carbon steel +
Electroless Nickel Plated trim, Devlon seats, HNBR seals, gear operated, meets NACE and is fire safe tested.

B T 3 B - F 0 6 0 - 1 2 1 0 R F - D H - N F G -

1 2 3 4 5 6 7 8 9 10 11 12 13

1. Valve Type 2. Service /Design Style 3. Body Design 4. Bore 5. Pressure Rating 6. Body Material
Code Description Code Description Code Description Code Description Code Class Code Description
BT Ball Valve 0 Adjustable Packing- A 1 pc End Entry R Reduced 015 Class 150 11 A105N
Trunnion (Commercial Design) B 2 pc Split- Bolted 030 Class 300 12 WCB
F Full
BF Ball Valve 1 Adjustable Packing- 040 Class 400 21 A105N/LF2
Floater C 2 pc Threaded S Standard Port
Flanged(API 608, 060 Class 600
ASME B16.34) 24 LCC
D 2 pc Seal Weld 090 Class 900
2 Adjustable Packing E 3 pc Bolted 150 Class 1500 36 CF8M
THRD,SW,NIPPLE,B 250 Class 2500 92 CS+ SS Seat
W Ends F 3 pc Threaded Pocket
450 Class 4500
(API 608, ASME G 3 pc Welded
B16.34)
3 O-Ring Stem Seal
4 Metal Seated Valve
7. Trim Material 8. End Connections 9. Seat 10. Seal 11. Features 12. Operator
Code Description Code Description Code Description Code Description Code Description Code Description
10 C.S. + ENP RF Flg-RF N Nylon V Viton NF NACE L Locking Lever
T PTFE H HNBR compliant, B Bare Stem
30 Stainless RJ Flg-RTJ
Fire Safe
Steel FF Flg-FF D Devlon L Low Temp. A Actuated
Tested
36 316SS / WW WE x WE H HNBR (-50 F.) O-Ring
NW NACE G Manual Gear
CF8M WF RF x WE R R-PTFE 9 PTFE-LIP SEAL compliant, H Non-locking
61 410 SS WJ RTJ x WE C TFM 4215 G Graphite Non-Fire Lever
Tested C Chain Wheel
M TFM 4105 T PTFE
13. Modifier Code WF Without
J TFM 1600 M TFM NACE, O Oval Hand
Code Description wheel
V Viton E EPDM Fire Safe
Special Tested S Spring Return
configurations. E EPDM F Delrin Lever
WW Without
F Delrin K Kel-F NACE Non-
Fire Tested

ISV Series No. BT3BF STANDARD FEATURES

Locking device
standard with
gear operator 2” square operating
Product Certifications
drive nut at hand
API 6D wheel hub.
Actuator Pad
API 607 Detachable hand 2-piece bolted
PED CE wheel body design.
Grease
injection fitting Design meets
for emergency API 6D, API
stem seal 608 & ASME
Secondary B16.34.
injection system
Blowout proof stem with separate Manufactured,
Internal Check tested and
Valve for monogrammed
Secondary in accordance
Low + high Sealing (standard
pressure seat with API 6D.
on 6” and larger,
sealing—Self optional on 2”-4”)
relieving seat Rugged
design polymeric seat
material

Each valve is
uniquely
serialized for
Metal backup enhanced
seats traceability.
accomplishes
fire safe 3 mil. Electroless Fire safe tested
functionality. Nickel Plated Trim to API 607 5th
is Standard Edition

Drain valve for block

NACE bolting is and bleed operation
standard

2
ISV Series No. BT3BF Two Piece Construction Trunnion Mounted Ball Valves

Material List of Trunnion Bal Valve (6” - 12” view)

No Part Name Materials
1 Body A216 WCB A352 LCC A351 CF8M
2 End Cap A216 WCB A352 LCC A351 CF8M
3 Ball A105N + ENP Low temp A350 LF2 + ENP A182 F316
4 Stem AISI 1045 + ENP Low temp. C.S. + ENP 17-4PH
5 Seat Insert 1) 1)
Devlon V (Class 150 & 300: 15% glass filled PTFE)
6 O-Ring HNBR Low temp. HNBR HNBR
7 Seat Ring A105N + ENP A350 LF2 + ENP A182 F316
8 Seat Gasket Graphite
9 Seat Pusher A105N + ENP A350 LF2 + ENP A182 F316
10 Seat Spring Inconel X-750
11 Gasket Graphite (Body-Cap Gasket is Graphite SPW 2)
12 Gland A105N + ENP A350 LF2 + ENP A182 F316
13 Trunnion A105N + ENP A350 LF2 + ENP A182 F316
14 Trunnion Cover 3) A105N A350 LF2 A182 F316
15 Anti-static ball 304SS
16 Anti-static spring 304SS
17 Stem Key C.S.
18 Bearing C.S. + PTFE (DU) S.S. + PTFE
4)
19 Thrust Washer S.S. + PTFE (DU) S.S. + PTFE 4)
20 Socket Cap Screw A574 (eq. B7M) A320 L7M A193 B8
21 Fire Seal Packing Graphite
22 Top Plate A105 + ENP A182 F316
23 Pin C.S.
24 Ball Thrust Washer PTFE 5)
25 Grease Injection Fitting Zinc plated carbon steel 316SS
26 Internal Check Valve Zinc plated carbon steel 316SS
27 Vent Plug Zinc plated carbon steel 316SS
28 Body Stud A193 B7M A320 L7M A193 B8
29 Body Nut A194 2HM A194 4M A194 8
30 Gear Stud C.S.
31 Gear Nut C.S.
32 Drain Valve Zinc plated carbon steel A276 316
33 Manual Gear Commercial Carbon Steel

1) Devlon is a registered trademark of the Devol Engineering company

2) 304SS Spiral wound graphite body gaskets
3) Applies only to 6” – 12” class 150 & class 300 valves
4) 2” – 4” class 150 & class 300 valves are equipped with PTFE bearings
5) 6” and larger valves are equipped with C.S. + PTFE (DU) bearings

3
 ISV Series No. BT3BF Two Piece Construction Trunnion Mounted Ball Valves

Working Pressures (psi) Pressure Test to API 6D (WCB body)

Class: 150 300 600 900 1500 Shell Test Seat Test Seat Test
O-ring Seals: HNBR HNBR HNBR HNBR HNBR (Hydrostatic) (Hydrostatic) (Air)
Seats Inserts: RPTFE RPTFE Devlon Devlon Devlon
Class 150 450 psi 313 psi 80 psi

Min. Temp: -20 deg. F. 285 740 1480 2220 3705 Class 300 1125 psi 814 psi 80 psi
Class 600 2225 psi 1628 psi 80 psi
Max. Temp: 300 deg. F. 230 500 1250 1979 at 280 F 3320 at 260F Class 900 3350 psi 2442 psi 80 psi
Class 1500 5575 psi 4076 psi 80 psi

Dimensions and Weights

Valve Size: NPS 2" 2 1/2" 3" 4" 6" 8" 10" 12"
d inch 2 2.5 3 4 6 8 10 12
L (RF) inch 7 7.5 8 9 15.5 18 21 24
L (BW) inch 8.5 9.5 11.13 12 18 20.5 22 25
Class L (RTJ) inch 7.5 8 8.5 9.5 16 18.5 21.5 24.5
150 H inch 6 6.5 7.63 8.4 10.9 12.6 15.56 18.13
W (Gear Hand wheel ) inch 18 18 24 24
RF 33 42 84 143 214 353 529 860
WT (lbs)
BW 39 38 77 121 205 340 501 805
d inch 2 2.5 3 4 6 8 10 12
L (RF) inch 8.5 9.5 11.13 12 15.88 19.75 22.4 25.5
L (BW) inch 8.5 9.5 11.13 12 15.88 20.51 22 25
Class L (RTJ) inch 9.13 10.12 11.75 12.64 16.5 20.4 23 26.14
300 H inch 6 6.5 7.63 8.4 10.9 12.6 15.56 18.13
W (Gear Hand wheel ) inch 18 18 24 24
RF 40 60 104 176 260 441 805 1169
WT (lbs)
BW 31 49 84 143 232 408 754 1109
d inch 2 2.5 3 4 6 8 10 12
L (RF) inch 11.5 13 14 17 22 26 31 33
L (BW) inch 11.5 13 14 17 22 26 31 33
Class L (RTJ) inch 11.63 13.13 14.13 17.13 22.13 26.13 31.14 33.13
600 H inch 7 6.5 7.7 8.4 10.7 13.5 19.5 22.88
W (Gear Hand wheel ) inch 18 18 24 24
RF 84 125 146 269 479 772 1565 2117
WT (lbs)
BW 69 113 128 258 441 721 1301 1742
d inch 2 2 1/2 3 4 6 8 10 12
L (RF) inch 14.50 16.50 15.00 18.00 24.00 29.00 33.00 38.00
L (BW) inch 14.50 16.50 15.00 18.00 24.00 29.00 33.00 38.00
Class L (RTJ) inch 14.63 16.63 15.13 18.13 24.13 29.13 33.13 38.13
900 H inch 8.25 8.50 8.86 10.43 13.00 16.14 17.71 19.67
W (Gear Hand wheel ) inch 18 18 24 24 24
RF 106 132 172 304 747 1411 2117 2932
WT (lbs)
BW 99 117 165 289 582 1192 1764 2447
d inch 2.00 2.50 3.00 4.00 5.75 7.67 ― ―
L (RF) inch 14.50 16.50 18.50 21.50 27.75 32.75 ― ―
L (BW) inch 14.50 16.50 18.50 21.50 27.75 32.75 ― ―
Class L (RTJ) inch 14.63 16.63 18.63 21.63 28.00 33.13 ― ―
1500 H inch 7.75 8.70 10.00 11.44 14.00 17.67 ― ―
W (Gear Hand wheel ) inch 18.00 18.00 24.00 24.00 ― ―
RF 121 176 258 476 1173 1918 ― ―
WT (lbs)
BW 113 157 181 331 913 1493 ― ―

International Standard Valve, Inc. 7111 Perimeter Park Drive, Bldg 320, Houston, Texas 77041

713-983-7600, [email protected] Bulletin No. ISV-SB210.6 Issue 02/2011