1.

Notes

This document applies only to bindings marked with serial numbers A0900000 through A0999999. The installation of the binding should only be performed by an authorized G3 dealer The G3 Onyx binding is compatible only with alpine touring ski-boots (ISO 9523) with TECH compatible inserts Bellowed touring boots, such as the Scarpa F1, F3 and Terminator X series boots, can only be used the Onyx boot shim installed. The shim is available as an accessory item from G3. Warning: Using a bellowed boot with the G3 Onyx binding will affect the safety release of the boot from the binding. G3 cannot guarantee the release settings of the binding when used with these boots. Refer to the instructions included with the Onyx boot shim for further details.

tap. Follow the ski manufacturers recommendation for ideal drill size. The G3 Onyx binding mounting pattern is compatible with Dynafit binding patterns. Use a G3 Onyx mounting jig, or Dynafit compatible jig to locate and drill holes in the ski. Set the jig to the boot sole size either by fitting the boot to the jig, or by setting the jig length to match the desired sole length. Table 3, ONYX Mounting Guide, at the end of this document can be used to determine the sole length range available for adjustment given a chosen mount size set by the jig. Place the jig on the ski and align the center mark of the jig to the center mark of the ski. If the ski does not have a center mark, either: a) use the ski manufacturers recommended measurement to locate the center mark b) locate the cord center of the ski and mark it. Align the jig such that boot toe is aligned to this mark. Fix the jig in place and drill the holes using the recommended drill size; either 3.5mm x 9mm or 4.1mm x 9mm. (4.1mm for skis with metal topsheet) Remove chips or dust from the holes. Holes should be glued with waterproof glue and/or tapped if recommended by the ski manufacturer. 2.2. Installation of the Binding Install the mounting plates by using the supplied screws and torquing the mounting screws to 4 Nm. Note: Always use G3 Onyx

mounting screws supplied with the binding. If the screws have become stripped or damaged, replace only with G3 Onyx mounting screws. Using incompatible screws will likely result in damage to the binding or ski, and possible separation of the binding from the ski. NOTE: Ensure the metal inserts are installed in the toe mounting plate before the plate is mounted to the ski. Mount the toe plate on the ski as shown in Figure 1 (5 toe mounting screws shown). Ensure the mounting plate is aligned properly to the mid line of the ski and is flush to the ski.

2.

Mounting and Installation

Inspect the ski and binding for any visual signs of damage or wear. Replace any worn or damaged parts. 2.1. Mounting Always follow the ski manufacturers recommendation for binding mounting location to ensure that the binding is mounted in the correct binding mounting area on the ski. The G3 Onyx is designed to mount to skis with drilled hole sizes from 3.5mm to 4.1mm x 9mm. For skis with a metal topsheets, use a 2009 G3 Genuine Guide Gear

Figure 1 Toe mounting plate and mounting screws

Mount the heel plate on the ski as shown in Figure 2 (4 heel mounting screws shown). Ensure the heel plate sits flush on the ski, and there is no gap between the plate and the ski. Check that the metal length adjustment plate is installed against the ski.

090316 Rev -

following section (In ISO 11088/ ASTM F939).

accordance

with

Figure 2 Heel mounting plate and mounting screws

Figure 5 Heel installation

2.3. Toe Installation Slide the toe unit backwards onto the toe mounting plate from the front/tip end of the toe mounting plate, and align the back edge of the toe unit with the 0 mm mark on the mounting plate as shown in Figure 3. Install the two countersunk toe positioning screws using a #3 Pozidrive screwdriver as shown in Figure 4, torque to 5.6 Nm. Note: the toe position can be moved in two 7.5mm increments to adjust the boot position on the ski and accommodate larger or smaller boot sizes.
Figure 6 Heel length adjustment

3.1. Setting of Lateral (Mz) Release Mz (twisting) DIN adjustment is located on the main heel body, above the boot length adjustment screw. (See Figure 8). Using a Phillips or Pozidrive #2. Screwdriver, turn adjuster clock-wise to increase release setting, and counter clock-wise to decrease setting.

Mz (Lateral) DIN Adjustment Boot Length adjustment

Figure 8 Lateral (Mz) Adjuster Location

Figure 7 Front Cowling Installation

2.5. Heel Location Setting WARNING: Binding performance is sensitive to the heel location being set accurately. Too large a gap could result in the binding releasing too easily, too small a gap will affect release values and can cause interference between the boot and binding while touring. It is very important to have a 6mm gap between the boot heel and the binding after installation. Install a ski boot into the binding with the heel in ski mode. Use a #3 Pozidrive screwdriver to adjust the boot length adjustment screw, as shown in figure 8. Use the supplied 6mm G3 spacer tool as shown in Figure 7, to set the gap between the binding and boot. The shim should fit snugly between the binding and the boot. Note: Do not over tighten the boot length adjustment screw.

3.2. Setting of Forward Falling (My) Release My (forward falling) DIN adjustment is located on the upper part of the heel (See Figure 9). Using a Phillips or Pozidrive #2, turn adjuster clock-wise to increase release setting, and counter clock-wise to decrease setting.

My (Forward Falling) DIN Adjustment

Figure 3 Toe installation

Figure 9 Forward Falling (My) Adjuster Location

3.3. Installation of the Leash Attachment Clip The ski leash clip should be installed on any binding that does not have a ski brake installed. The toe piece must be off the ski to be able to install the clip. The leash clip can be installed on either the left or right side of the toe piece. Spread the ends of the clip and insert into the holes on the underside of the toe piece. Fold the clip flat.

Figure 4 Toe positioning

2.4. Heel Installation WARNING: Heel installations and removals from the base plates must be performed with the lateral release setting set to its minimum. Failure to do this could result in damage to the binding. Slide the heel forwards onto the heel mounting plate from the rear/tail end of the heel mounting plate until it makes contact with the length adjustment plate and is approximately in the position shown in Figure 5. While pushing slightly forward on the heel and turning the length adjustment screw clockwise with a #3 pozidrive screwdriver, adjust the position of the heel until it is approximately in the centre of its adjustment range (as shown by the position indicator in Figure 6). Install the heel front cowling by installing the two small countersunk front cowling screws into the heel with either a #1 phillips or a #1 Pozidrive screwdriver and torque them to 1.1Nm. 2009 G3 Genuine Guide Gear

Figure 7 Heel gap setting

Figure 10 Leash Clip Installation

3.

Release Value Adjustment

The G3 Onyx binding has two release modes: lateral twisting (Mz), and forward falling (My). Your G3 ONYX binding has a lateral twist (Mz) release setting scale from 6-12, and a forward falling (My) release setting scale from 5-10. Please choose an appropriate value using the selection of release values chart provided in the

090316 Rev -

4.

Selection of Release Setting Values (ISO 11088/ ASTM F939)

selection with a (+) symbol. For example Type 3+ 4.2. Selection of Release Settings Locate the skiers weight (mass) and height in the appropriate column in Table 2. If weight and height are not on the same line, select the line closest to the top of the table. Adjustment for skier type (see 4.1): For a Type 1 skier, stay on the line and use that skier code. For a Type 2 skier, move down the table one skier code. For a Type 3 skier, move down the table two skier codes.

heel location by checking gap between boot and binding. both lateral twisting (Mz), and forward falling (My) adjustments on both bindings are set to the correct value. lateral release travel by hitting the heel of the boot to displace it several mm and ensure that the binding returns to center quickly and smoothly. heel pins do not interfere with the boot when the binding is in tour mode, and that the heel can easily be engaged and disengaged from tour mode. toe positioning screws are tightened to the correct torque verify release values with a binding test device. Follow the manufacturers instructions for Dynafit compatible bindings.

4.1. Determination of Skier Type It is the responsibility of the skier to determine his/her skier-type classification as defined in Table 1 Table 1 Determination of Skier-type Classification
Skiers that do not meet the descriptions of either

1 or 3

Type 1
Cautious skiing on smooth slopes of gentle to moderate pitch Skiers who designate themselves as Type 1 receive lower than average release settings. This corresponds to an increased risk of inadvertent binding release in a fall. This type also applies to entry level skiers uncertain of their skill level.

Type 2

Type 3
Fast skiing on slopes of moderate to steep pitch.

If the skier is age 9 and younger, or 50 and older, move up the table one skier code. If separate lateral twist (Mz) and forward lean (My) skier types were selected, repeat the selection of release settings above for the second skier type, recored the resulting codes in the order LT/FL. 4.3. Release Value Determination Locate the release value at the intersection of the skier code row and the appropriate boot sole length. If there is a blank box, move left or right to the in same row to the next value. Note that release values selected using this practice may not be appropriate for circumstances in which: the skier carries an object that significantly increases the skiers effective body weight, The skier grasps or in some manner controls an object such as a sled, or the skier encounters exceptional snow or terrain conditions not commonly developed ski slopes. found on

6.

Troubleshooting

Skiers who designate themselves as Type 2 receive average release settings appropriate for most recreational skiing.

Skiers who designate themselves as Type 3 receive higher than average release settings. This corresponds to decreased capacity for release in a fall, in order to gain a decreased risk of inadvertent binding release.

If the lateral release (Mz) is not symmetrical, check the following: worn boot inserts toe piece alignment with the heel. Check by installing boot in toe and checking that binding heel pins are aligned with boot heel insert. Test with multiple boots to ensure that boot heel and toe inserts are correctly aligned in boot. dirt contamination or excessive wear of binding components, in particular the toe pins or heel pins. heel location by checking gap between boot and binding. Refer to section 2.5.

Skiers 10 years of age or older of any type who desire a higher or lower setting than the setting of their skier type according to Table 1, may do so in the following cases: Skiers who have satisfactory experience with lower settings regarding these recommenddations may request setting based on their experience. Skiers who have satisfactory experience without inadvertent releases may request a setting up to 15% lower than that recommended in Table 2 Skiers having certain characteristics, such as neutral skiing technique, defensive attitude, high degree of control, etc. may request a setting of 15% lower than that recommended in Table 2. Skiers who have experienced inadvertent releases may request a setting up to 15% higher than that recommended in Table 2. Skiers may request settings that are different for lateral twist and forward lean. If a skier selects a different skier type for forward lean, record the choice with a (/) separating the two types, in the order lateral twist/forward lean (LT/FL) If a skier selects discretionary settings lower than those derived from Type 1, record this selection with a (-) symbol. For example Type 1 If a skier selects discretionary settings higher than those derived from Type 3, record this

7.

Instructions to Customer

Release torque values outside the recommendations of this practice may increase the risk of injury to the skier. However, skiers who are informed of this potential risk may request such settings and have them provided, subject to the guidelines and limitations specified in this document. These values refer to recommended release torque for initial adjustment of a ski binding and subsequent readjustment of the binding during routine maintenance or following a suspected malfunction. However, these values are not intended to apply to the condition of the equipment at any time after it is put into use.

Explain the operation and features of the binding. In particular: Switch from ski to tour mode Correct operation of heel lifts Use of toe tour mode lock Explain the importance of regular maintenance and performance checks. The binding should be kept free of dirt and other contamination and that at the beginning of each season, and/or after 60days of skiing, G3 Onyx bindings be checked by an authorized G3 dealer and have the release setting recalibrated Explain that the binding release values are set to the customers personalized settings. Tell the customer the setting values selected, and where the setting adjustments are located. Explain the importance of having the binding adjusted correctly for boot sole length. If the customer experiences any problems or issues with the boot, binding or ski, they should contact an authorized G3 dealer.

5.

Checks and Functional Tests

Upon completing installation and setting of the binding, the following inspection and functional checks should be performed: boot center mark is aligned with the ski center mark toe piece with the heel piece alignment by installing a boot in the binding, and checking that the binding heel pins are aligned with the boot insert.

8.

Warranty

For complete warranty information, please visit: http://www.genuineguidegear/warranty

2009 G3 Genuine Guide Gear

090316 Rev -

Table 2 Release Value Selection Using Skiers Weight

Skier's Parameters Skier's Mass kg 10 14 18 22 26 31 36 42 49 58 67 79 95 to to to to to to to to to to to to < 13 17 21 25 30 35 41 48 57 66 78 94 Skier's Height m 22 31 40 49 57 68 79 93 108 128 148 174 209 Skier's Mass lbs to to to to to to to to to to to to < 29 37 46 55 66 77 90 106 126 146 172 207 Skier's Height ft in Initial Indicator value, Z (presetting), depending on boot sole length Inspection Parameters

1.5 1.6 1.7 1.8 2

< to to to to <

1.5 1.6 1.7 1.8 1.9

4'11" 5'2" 5'6" 5'11" 6'5"

< to to to to <

4'10" 5'2" 5'5" 5'10" 6'4"

Lateral ForwSkier 251 mm 271 mm 291 mm 311 mm <250m >331 Twist ard Lean Code to to to to Mz My m mm 270 mm 290 mm 310 mm 330 mm Nm Nm 5 18 A 0.75 0.75 8 29 B 1 1 0.75 11 40 C 1.5 1.25 1 14 52 D 1.75 1.5 1.5 1.25 17 64 E 2.25 2 1.75 1.5 1.5 20 75 F 2.75 2.5 2.25 2 1.75 1.75 23 87 G 3.5 3 2.75 2.5 2.25 2 27 102 H 3.5 3 3 2.75 2.5 31 120 I 4.5 4 3.5 3.5 3 37 141 J 5.5 5 4.5 4 3.5 43 165 K 6.5 6 5.5 5 4.5 50 194 L 7.5 7 6.5 6 5.5 58 229 M 8.5 8 7 6.5 67 271 10 9.5 8.5 8 78 320 N 11.5 11 10 9.5 91 380 O P 105 452 118 540

Table 3 - ONYX Mounting Guide

Boot Sole Length

270

273

275

278

280

283

285

288

290

293

295

298

300

303

305

308

310

313

315

318

320

323

325

328

330

333

335

338

340

343

345

Fit Range 270 273 275 278 280 283 285 288 290 293 295 298 300 303 305 308 310 313 315 318 320 323 325 328 330 333 335 338 340 343 345 348
253mm-285mm 255mm-288mm 258mm-290mm 260mm-293mm 263mm-295mm 265mm-298mm 268mm-300mm 270mm-303mm 273mm-305mm 275mm-308mm 278mm-310mm 280mm-313mm 283mm-315mm 285mm-318mm 288mm-320mm 290mm-323mm 293mm-325mm 295mm-328mm 298mm-330mm 300mm-333mm 303mm-335mm 305mm-338mm 308mm-340mm 310mm-343mm 313mm-345mm 315mm-348mm 318mm-350mm 320mm-353mm 323mm-355mm 325mm-358mm 328mm-360mm 330mm-363mm

Dynafit Mounting Jig Boot Size* (mm)

* This table ONLY applies to the boot length setting on Dynafit brand mounting jigs.

Ideal Fit

Variation in Boot Sole length measurement may cause fit issues

2009 G3 Genuine Guide Gear

348

090316 Rev -