8x12 Tiny House
8x12 Tiny House
8x12 Tiny House
These framing plans were not prepared by or checked by a licensed engineer and/or architect. TinyHouseDesign.com does not represent or imply itself to be a licensed engineer and/or a licensed architect. Enjoy these free house plans but use them at your own risk. 2011 TinyHouseDesign.com - Simple 8x12 Shed
2x6 ridge
Cross section and overview perspectives. Roof has a 12/12 pitch. 2011 TinyHouseDesign.com - Simple 8x12 Shed
144"
141"
90"
96"
16"
Floor framing details. Building could be placed on slab, piers, or your choice of foundation. 2011 TinyHouseDesign.com - Simple 8x12 Shed
48"
96"
48"
48"
96"
34"
40"
48"
89" 1 1/2"
34" 90 3/4" 48" Back wall detail. Notice that the plywood is cut 1 1/2" short. This leaves the top plate available for the gable sheathing. Diagram in lower left shows step in construction process on this and following pages. 2011 TinyHouseDesign.com - Simple 8x12 Shed
40"
81 1/2"
86"
137"
144"
16"
96"
48"
48"
48"
Right wall details. See notch details on next page. 2011 TinyHouseDesign.com - Simple 8x12 Shed
81 1/2"
86"
14 1/2 "
14 1/2 "
13 3/4 "
16"
16"
On pages later in the plans you'll see details on making boxed eaves, which are admittedly overkill if you were to also notch the siding. Both seal the roof so doing both may be redundant. As an option you could either skip the boxed eave, or skip the notched exterior sheathing shown on this page. If you were to skip these notches you could simply cut the plywood off at the top of the wall.
13 3/4" 1 1/2" 1 1/2"
6 1/4"
Sheathing notching detail. Notice that the notches are 16" O.C. except at the ends of the wall. Those end notched are also deeper. The notches allow the rafters to be seated and helps seat the roof. 2011 TinyHouseDesign.com - Simple 8x12 Shed
7 3/4"
144" 137"
40"
16"
48"
48"
34" 96"
34"
48"
48"
48"
81 1/2"
86"
34"
34"
40"
96"
81 1/2"
34"
27 1/2"
83"
27 1/2" 1 1/2" 90 3/4" 34" 48" 83" Front Wall 2011 TinyHouseDesign.com - Simple 8x12 Shed 6 1/4"
86"
96"
61
44 1/2"
7/ 8"
16"
46"
1 1/2"
66
7/ 8"
46"
7"
48"
5 3/4"
96"
61 8" 7/
44 1/2"
46"
1 1/2"
66
7/ 8"
46"
7"
48" 5 3/4" Front Wall Gable 2011 TinyHouseDesign.com - Simple 8x12 Shed
Ridge beam fits right on top of gable walls and into slots in siding/sheathing. 2011 TinyHouseDesign.com - Simple 8x12 Shed
72
1/ 2"
61 8" 7/
2 3/4"
3 1/2"
4"
Roof rafters and birds mouth detail for common rafters. 2011 TinyHouseDesign.com - Simple 8x12 Shed
2 1/2"
72
1/ 2"
61
7/ 8"
4 1/4"
3 1/2"
4"
Roof rafters and birds mouth detail for end rafters. 2011 TinyHouseDesign.com - Simple 8x12 Shed
4"
16"
Roof framing detail. In the image above you can see how the end rafters are a little different than the common rafters. 2011 TinyHouseDesign.com - Simple 8x12 Shed
165"
26 8" 5/
1 1/2"
" 48
" 28
" 96
" 44
Roof sheathing detail. An attempt is made to always have plywood ends meet on a rafter. An effort was made to reduce cutting plywood, but on a roof this small there's pretty much nothing for it. 2011 TinyHouseDesign.com - Simple 8x12 Shed
boxed eave
Boxed side eaves and gable eave trim detail. Bottom right illustration shows why the end rafters are slightly different from the common rafters. They make a clean boxed eave. 2011 TinyHouseDesign.com - Simple 8x12 Shed
Roofing installed over roofing felt. This would also be a good time to apply house wrap to the walls. 2011 TinyHouseDesign.com - Simple 8x12 Shed
Install windows and doors. House wrap not shown. 2011 TinyHouseDesign.com - Simple 8x12 Shed
Siding applied. Shingles illustrated here. 2011 TinyHouseDesign.com - Simple 8x12 Shed