Clap Switch

Nov.24, 2010 in New Circuits

Here is a Hobby Circuit for electronics hobbyists that can switch on & off a light, Fan, Radio etc. by the sound of clap.The sound of clap is received by a small microphone that is shown biased by resistor R1 in the circuit. The microphone changes sound wave in to electrical wave which is further amplified by Q1.Transistor Q1 is used as common emitter circuit to amplify weak signals received by the microphone. Amplified output from the collector of transistor Q1 is then feed to the Bistable Multivibrator circuit also known as flip-flop. Flip flop circuit is made by using 2 Transistor, in our circuit Q2&Q3. In a flip-flop circuit, at a time only one transistor conduct and other cut off and when it gets a trigger pulse from outside source then first transistor is cutoff and 2nd transistor conducts. Thus output of transistor is either logic-0 or logic-1 and it remains in one state 0 or 1 until it gets trigger pulse from outer source. The pulse of clap which is a trigger for flip-flop which makes changes to the output which is complementary (reverse). Output of flip-flop which is in the low current form is unable to drive relay directly so we have used a current amplifier circuit by using Q4 which is a common emitter circuit. Output of Q4 is connected to a Relay (Electromagnetic switch), works like a mechanical switch. With the help of a relay it is easy for connecting other electrical appliance. The relay contact is connected to the power line and hence turns on/off any electrical appliance connected all the way through relay.

Circuit Diagram of Clap Switch

How Clap Switch Works Part List: Resistors R1= 15K,R5,R6= 1.5K R2,R11,R12= 2.2M,R13= 2.2K

R3= 270K,R4= 3.3K R7,R8= 10K,R9,R10= 27K Capacitors C1=1000f/16v C2=.01f,C3,C4=.047f Semiconductor Q1,Q2,Q3= BC548 D2,D3,D4= IN 4148 D1,D5= IN 4007,Q4= BC368 Misc T1= 12v/500mA Transformer Mic= Condenser Microphone K1= 12V Relay,B1= Bulb or Load

2nd Clap Switch Circuit

A clap switch circuit is a classic beginners project. Equipment can be switched on and off by just clapping your hands. Add a tiny microcontroller and you can easily build-in some more useful features. The microcontroller in this circuit makes it a simple job to add some useful features that are not seen on other clap switch designs:

Clap Switch circuit diagram

 Changeover relay contacts enable the unit to be wired in conjunction with a manual changeover switch so that manual override of the switched equipment is always possible. The unit is only responsive to a specific sequence of sounds i.e., two claps within a defined time window. A safety feature masks the input for a given time window if misuse (repeated commands) is detected (useful if children have discovered how it works). The safety feature and two-clap sequence detector can be built using TTL or CMOS flip-flops but by using a single microcontroller the circuit can be greatly simplified. A mains power supply is included so no additional power source is required. The Microchip flash PIC12F629 microcontroller is a neat device; the small 8-pin package contains a complete microcontroller including clock generator, reset circuitry, Flash ROM, RAM and EEPROM. Two of the eight pins are used for the supply connections while the remaining six are general-purpose I/O pins. A few of these pins have special function like the comparator inputs. The sound sensitivity of the circuit can be adjusted by programming the comparator threshold level in software.

Maplin Velleman Clap On/Off switch Video

Ready-made clap switch products

Velleman Clap On/ Off Switch : MK139 at only $17 Microprocessor controlled! Electronic kit, assembly required. Operates your lighting with a simple handclap!

RF Clapper Plus Cl84512 at $25 Clap Your Hands & Turn Your Appliances On Or Off Now With RF Technology You Can Also Press A Remote Control Button & Your Lights Will Effortlessly Turn On Or Off. The circuit diagram in Figure 1 shows that besides the microcontroller there are very few other components. The two-pin electret microphone produces an electrical signal in response to sound pressure waves. Transistor T1 amplifies the signal and preset P1 allows some adjustment of the circuit sensitivity by altering the bias voltage of T1. Two of the PIC output pins are used to drive a bistable relay via transistors T2 and T3. This type of relay has two energising coils. A short electrical pulse on one of the coils is enough to switch the relay in one direction while a pulse to the other coil will cause the relay to switch back. This type of relay has two main advantages: the relay is latching in both open and close direction so a short pulse is all that is necessary to switch it. Secondly the latching feature ensures that the relay retains its switched state even during a power failure. Changeover relay contacts enable the unit to be wired together with a changeover type manual switch, allowing the equipment to be switched manually if for any reason the clap switch is switched off. Pins 2 and 7 are used to switch a twocolour LED providing a visual indication of the switched state of the relay. The last output pin of the PIC is not used and is connected to a jumper to allow switching software options. Clapping relay Software When the signal level at GP1 goes low (clap detected) the program waits for approximately 200 ms during which time the LED glows red. After this period the LED switches to green and the software samples the input for approximately three seconds. If a second clap is detected during this period, the controller switches the output. After switching, the controller ignores any further clap sounds for approximately 10 s and the LED lights red. The output state is stored in EEPROM so that if a power failure occurs the software will switch the correct relay coil when power is re-established. A safety feature counts each switching event on an internal counter, which is decremented slowly in software. Should this counter exceed a threshold level, the circuit will ignore any input signals for approximately one minute and the LED blinks red. This will ensure that the circuit does not respond to an extended burst of noise (e.g., applause).

Clap switch PCB

The PCB layout shown in Figure 2 accommodates all components apart from the electret microphone. This is attached to the board at the MIC +/ connections with a length of shielded audio lead (keep the wire length to less than around 10 cm). Mounting the components onto the PCB should be quite straightforward. Start by fitting the single wire bridge next to rectifier B1. Ensure that all polarised components (diodes, LEDs, capacitors and the IC) are fitted the correct way round. The LED leads should be trimmed so that when it is soldered to the board it protrudes through a hole in the lid when the case is assembled; alternatively use a translucent enclosure. Once all components have been fitted and all solder connections have been inspected the PCB can be fitted into an insulated enclosure. The mains input lead will require some form of strain relief. Be aware that some tracks carry lethal voltages. All appropriate safety guidelines must therefore be adhered to. A small hole can be made in the lid directly over preset P1 if it is necessary to adjust the sensitivity of the circuitwithout dismantling the unit. Lastly, dont forget to add perforations in the case so that sound waves can reach the microphone capsule. Clap switch COMPONENTS LIST: Resistors: R1,R6,R7 = 4k7 R2 = 150k R3 = 22k R4 = 10k R5 = 150 P1 = 100k preset H Capacitors: C1 = 220F 25V radial C2 = 100nF C3 = 1F 16V Semiconductors: B1 = B80C1500 (round case, 80V piv, 1.5A) D1,D2 = 1N4148 D3 = bicolour LED (red/green) IC1 = 78L05 IC2 = PIC12F629CP, programmed T1,T2,T3 = BC238 or BC547 Miscellaneous: JP1 = 2-way pinheader with jumper

K1 = 2-way PCB terminal block, lead pitch 7.5mm K2 = 3- way PCB terminal block, lead pitch 7.5mm MIC1 = 2-terminal electret microphone capsule Re1 = bistable relay, 2 x changeover (e.g., Schrack RT314F12) Tr1 = mains transformer 1 x 6V, min. 2VA, short-circuit proof (e.g., Marschner VN30.15/10522 or Era 030-7340.0T; Conrad Electronics # 506141)

Sensitive Clap Switch circuit

This is the circuit of a very sensitive clap switch. It switches ON/OFF a White LED or electrical appliances through claps. The circuit can sense the sound of claps from a distance of 1-2 meters. Condenser Mic picks up sound vibrations caused by the clap. These sound vibrations are given to the inverting input (pin2) of IC1. It amplifies the sound collected by the Mic.

Resistor R2, R3 and variable resistor VR1 adjust the sensitivity of the amplifier. Resistor R1 set the sensitivity of Mic. The amplified output pulses from IC1 passes to the input of IC2 (CD 4017). Resistor R4 keeps the input (pin14) of IC2 low so as to prevent false triggering. IC2 is a decade counter IC which is wired as a toggle switch. That its outputs 1 and 2 (pins 2 and 3) becomes high and low when the input pin14 receives pulses. Pin4 (output4) is connected to the reset pin15 so that further counting will be inhibited. The high output from IC2 passes through the current limiter R6 to the base of switching transistor T1. When T1 conducts, White LED (D2) turns on. If a 6V 100 ohms relay is connected to the points marked (A and B), the relay will also energize and the load (bulb or electrical equipments) will be switched on. In the next clap, output pin 2 becomes low and relay and White LED will be switched off. LED D1 (Red LED) indicates the OFF position.

PCB Layout of Sensitive Clap Switch Circuit

PCB Relay Pins 2 + 5 Relay coil 1 Common- Here connect the phase line 3 NO ( Normally Open) Here connect the load phase in series to switch ON the load when relay turns on 4 NC ( Normally Connected) Here connect the load phase in series to switch OFF the load when relay turns on In the PCB layout, points A and B are used to connect relay coil pins 2 and 5

4017 IC datasheet