Scribd Logo
Upload

Welcome to Scribd!

  • 217 views

    Audi TT Sec Air

    Uploaded by

    donghungco08
    The document discusses checking the secondary air injection system on a vehicle. It describes the function of the system to inject air into the exhaust system during cold starts to help the catalytic converter heat up faster. It provides instructions on checking components like the air injection solenoid valve and air pump relay for proper operation, including measuring electrical values and activating components through diagnostic testing. Replacing components if electrical faults are found is recommended.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd

    Audi TT Sec Air

    Uploaded by

    donghungco08
    217 views21 pages
    The document discusses checking the secondary air injection system on a vehicle. It describes the function of the system to inject air into the exhaust system during cold starts to help the catalytic converter heat up faster. It provides instructions on checking components like the air injection solenoid valve and air pump relay for proper operation, including measuring electrical values and activating components through diagnostic testing. Replacing components if electrical faults are found is recommended.

    Original Title

    Audi_TT_Sec_Air

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document discusses checking the secondary air injection system on a vehicle. It describes the function of the system to inject air into the exhaust system during cold starts to help the catalytic converter heat up faster. It provides instructions on checking components like the air injection solenoid valve and air pump relay for proper operation, including measuring electrical values and activating components through diagnostic testing. Replacing components if electrical faults are found is recommended.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    217 views21 pages

    Audi TT Sec Air

    Uploaded by

    donghungco08
    The document discusses checking the secondary air injection system on a vehicle. It describes the function of the system to inject air into the exhaust system during cold starts to help the catalytic converter heat up faster. It provides instructions on checking components like the air injection solenoid valve and air pump relay for proper operation, including measuring electrical values and activating components through diagnostic testing. Replacing components if electrical faults are found is recommended.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 21

    Secondary Air Injection (AIR) system, checking

    Page 1 of 21

    26-29

    Secondary Air Injection (AIR) system, checking


    The Secondary Air Injection (AIR) system causes the catalytic converter to heat up more quickly, resulting in earlier operating readiness following cold start. Principle Due to overenrichment of the mixture during the cold start phase, there is an increased amount of uncombusted carbon monoxide in the exhaust. Secondary Air Injection (AIR) improves secondary oxidation in the catalytic converter and therefore reduces emissions. The heat produced by secondary oxidation greatly reduces start-up

    http://127.0.0.1:8080/audi/servlet/Display?action=Goto&target=_top&type=repair&id... 27/02/2005

    Secondary Air Injection (AIR) system, checking

    Page 2 of 21

    time for the catalytic converter, therefore improving exhaust quality during the cold start phase significantly.

    http://127.0.0.1:8080/audi/servlet/Display?action=Goto&target=_top&type=repair&id... 27/02/2005

    Secondary Air Injection (AIR) system, checking

    Page 3 of 21

    26-30

    Function In the cold start phase, the ECM -2activates the secondary air pump 12- via the relay for Secondary Air Injection (AIR) pump -1-. Air reaches the combination valve for Secondary Air Injection (AIR) -10-. The Secondary Air Injection (AIR) valve -3- is activated in parallel, which allows the vacuum to reach the combination valve for Secondary Air Injection (AIR) -10and the vacuum diaphragm for charge air pressure regulation 7-. The combination valve for Secondary Air Injection (AIR)

    http://127.0.0.1:8080/audi/servlet/Display?action=Goto&target=_top&type=repair&id... 27/02/2005

    Secondary Air Injection (AIR) system, checking

    Page 4 of 21

    thereby opens the path for secondary air to the exhaust channels of the cylinder head.

    http://127.0.0.1:8080/audi/servlet/Display?action=Goto&target=_top&type=repair&id... 27/02/2005

    Secondary Air Injection (AIR) system, checking

    Page 5 of 21

    26-31

    To prevent unnecessary heating, secondary air is diverted passed the turbocharger -8-. For this, the charge air pressure regulation pressure unit opens the charge air pressure valve. The pressure unit, designed as a double reservoir, has a vacuum connection for this on the intake side. 1 - Secondary Air Injection (AIR) pump relayJ2992 - Motronic Engine Control Module (ECM) J2203 - Secondary Air Injection (AIR) solenoid valve N112 -

    http://127.0.0.1:8080/audi/servlet/Display?action=Goto&target=_top&type=repair&id... 27/02/2005

    Secondary Air Injection (AIR) system, checking

    Page 6 of 21

    4 - Intake manifold

    http://127.0.0.1:8080/audi/servlet/Display?action=Goto&target=_top&type=repair&id... 27/02/2005

    Secondary Air Injection (AIR) system, checking

    Page 7 of 21

    26-32

    5 - Checkvalve Installed position (light/dark half): Arrow points in direction of flow, as shown in figure. 6 - Vacuum reservoir 7 - Pressure unit for charge air pressure regulation 8 Turbocharger 9 - Cylinder head 10 Combination - valve for secondary air injection (AIR) 11 - Air filter housing 12 - Secondary Air Injection (AIR) pump motor V101-

    http://127.0.0.1:8080/audi/servlet/Display?action=Goto&target=_top&type=repair&id... 27/02/2005

    Secondary Air Injection (AIR) system, checking

    Page 8 of 21

    26-33

    Secondary Air Injection (AIR) solenoid valve N112 -, checking


    Special tools and equipment VAG1526A VAG1527B VAG1594A VAG1598/31 VAS5051 - or VAG1551 with VAG1551/3A

    http://127.0.0.1:8080/audi/servlet/Display?action=Goto&target=_top&type=repair&id... 27/02/2005

    Secondary Air Injection (AIR) system, checking

    Page 9 of 21

    26-34

    Component location locations

    Overview of compon

    Repair Manual , 1.8 Liter 4-Cyl. 5V Turbo Injection & Ignition, Engine Code(s): AMU, Repair Group 24, Fuel preparation, injection Test requirement: Output Diagnostic Test Mode (DTM) performed Checking internal resistance - Disconnect harness connector from Seco Air Injection (AIR) valve N112 -. - Connect multimeter at valve for resistanc measurement. Specified value: 25 - 35 - If specified value is not obtained, replace Secondary Air Injection (AIR) solenoid va N112 -.

    http://127.0.0.1:8080/audi/servlet/Display?action=Goto&target=_top&type=repair&id... 27/02/2005

    Secondary Air Injection (AIR) system, checking

    Page 10 of 21

    26-35

    Checking voltage supply - Disconnect harness connector from Seco Air Injection (AIR) valve N112 -. - Connect VAG1527B voltage tester as foll Harness connector terminal 1 Engine Ground (GN Measure to

    - Operate starter briefly (engine can also s LED must light up. If LED does not light up: - Perform the following tests marked with d Check fuse -S243- (in fuse holder, posit

    http://127.0.0.1:8080/audi/servlet/Display?action=Goto&target=_top&type=repair&id... 27/02/2005

    Secondary Air Injection (AIR) system, checking

    Page 11 of 21

    26-36

    Check wire connection from terminal 1 of connector via fuse S243- (in fuse holder, socket 43) to Fuel Pump (FP) relay for open circuit: Electrical Wiring Diagrams, Troubleshooting & Component Locations Check Fuel Pump (FP) relay Repair Manual , 1.8 Liter 4-Cyl. 5V Turbo Fuel Injection & Ignition, Engine Code(s): AMU, Repair Group 24, Fuel preparation, injection Checking activation - Connect VAG1527B voltage tester as follows: Harness connector Measure to terminal 2 B+

    http://127.0.0.1:8080/audi/servlet/Display?action=Goto&target=_top&type=repair&id... 27/02/2005

    Secondary Air Injection (AIR) system, checking

    Page 12 of 21

    26-37

    - Initiate output Diagnostic Test Mode (DT activate Secondary Air Injection (AIR) so valve N112 Repair Manual , 1.8 Liter 4-Cyl. 5V Turb Injection & Ignition, Engine Code(s): AMU, Repair Group 24, Fuel preparation, injectio
    Output Diagnostic Test Mode

    Indicated on display
    N112

    Secondary air injection solenoid valve -

    LED must blink. If LED does not blink or if it remains consta - Connect VAG1598/31 test box at wiring to ECM, do not connect ECM. Repair Manual , 1.8 Liter 4-Cyl. 5V Turb Injection & Ignition, Engine Code(s): AMU, Group 24, Fuel preparation, injection - Check the following wire connections for circuit and short circuit to Ground (GND) Harness connector VAG 1598/31 testi terminal 2 Bushing 9

    - Repair open circuit or short circuit if nece - If wire connection is OK: Replace Engine Control Module (ECM) Repair Manual , 1.8 Liter 4-Cyl. 5V Turb Injection & Ignition, Engine Code(s): AMU, Group 24, Fuel preparation, injection

    http://127.0.0.1:8080/audi/servlet/Display?action=Goto&target=_top&type=repair&id... 27/02/2005

    Secondary Air Injection (AIR) system, checking

    Page 13 of 21

    26-38

    Secondary Air Injection (AIR) pump relay -J299and activation, checking


    Special tools and equipment VAG1526A VAG1527B VAG1594A VAG1598/31

    http://127.0.0.1:8080/audi/servlet/Display?action=Goto&target=_top&type=repair&id... 27/02/2005

    Secondary Air Injection (AIR) system, checking

    Page 14 of 21

    26-39

    Component location locations

    Overview of component

    Repair Manual , 1.8 Liter 4-Cyl. 5V Turbo Fuel Injection & Ignition, Engine Code(s): AMU, Repair Group 24, Fuel preparation, injection - Initiate output Diagnostic Test Mode (DTM) and activate Secondary Air Injection (AIR) pump relay -J299Repair Manual , 1.8 Liter 4-Cyl. 5V Turbo Fuel Injection & Ignition, Engine Code(s): AMU, Repair Group 24, Fuel preparation, injection Secondary Air Injection (AIR) pump relay (under cover, left at bulkhead) must trigger and the Secondary Air Injection (AIR) pump motor -V101- must run. A - If relay does not trigger: - Check voltage supply of the Secondary Air Injection (AIR) pump relay Page 26-40 . - Check activation of the Secondary Air Injection (AIR) pump relay Page 26-42 . B - If relay triggers, but Secondary Air Injection (AIR) pump does not run: - Check voltage supply of the Secondary Air Injection (AIR) pump motor Page 26-43 .

    http://127.0.0.1:8080/audi/servlet/Display?action=Goto&target=_top&type=repair&id... 27/02/2005

    Secondary Air Injection (AIR) system, checking

    Page 15 of 21

    26-40

    Checking voltage supply of Secondary A Injection (AIR) pump relay - Switch ignition off. - Remove Secondary Air Injection (AIR) pu relay - Connect multimeter for voltage measurem follows: Relay carrier below cover, left at bulkhead terminal 1 Engine G (GND Measure

    Specified value: approx. battery volta If specified value is not obtained: - Perform the following tests marked with d Check fuse -S131- (50 A) in main fuse box/battery. Check wire connection from B+ (termina fuse -S131- for Secondary Air Injection pump relay -J299- (below cover, left at bulkhead) for open circuit. Electrical Wiring Diagrams, Troubleshoo Component Locations

    http://127.0.0.1:8080/audi/servlet/Display?action=Goto&target=_top&type=repair&id... 27/02/2005

    Secondary Air Injection (AIR) system, checking

    Page 16 of 21

    26-41

    - Connect multimeter for voltage measurem follows: Relay carrier below cover, left at bulkhead terminal 3 Engine G (GND Measure

    - Operate starter briefly (engine can also s Specified value: approx. battery volta If specified value is not obtained: - Perform the following tests marked with d Check fuse -S243- (in fuse holder, posit Check wire connection from B+ (termina fuse -S131- for Secondary Air Injection pump relay -J299- (below cover, left at bulkhead) for open circuit. Electrical Wiring Diagrams, Troubleshoo Component Locations

    http://127.0.0.1:8080/audi/servlet/Display?action=Goto&target=_top&type=repair&id... 27/02/2005

    Secondary Air Injection (AIR) system, checking

    Page 17 of 21

    26-42

    Check activation of the Secondary Air Injection (AIR) pump relay - Switch ignition off. - Remove Secondary Air Injection (AIR) pump relay - Connect multimeter for voltage measurement as follows: Relay carrier below cover, left at bulkhead terminal 4 B+ Measure to

    - Initiate output Diagnostic Test Mode (DTM) and activate Secondary Air Injection (AIR) pump relay -J299Repair Manual , 1.8 Liter 4-Cyl. 5V Turbo Fuel Injection & Ignition, Engine Code(s): AMU, Repair Group 24, Fuel preparation, injection Specified value: approx. battery voltage If specified value is not obtained: - Switch ignition off. - Connect VAG1598/31 test box at wiring harness to ECM, do not connect ECM. Repair Manual , 1.8 Liter 4-Cyl. 5V Turbo Fuel Injection & Ignition, Engine Code(s): AMU, Repair Group 24, Fuel preparation, injection

    http://127.0.0.1:8080/audi/servlet/Display?action=Goto&target=_top&type=repair&id... 27/02/2005

    Secondary Air Injection (AIR) system, checking

    Page 18 of 21

    26-43

    - Check the following wire connection for open circuit and short circuit to Ground (GND) and B+: Relay carrier below cover, left at bulkhead terminal 4 - Repair open circuit or short circuit if necessary. If no malfunctions are detected: - Replace Secondary Air Injection (AIR) pump relay -J299-. Check voltage supply of the Secondary Air Injection (AIR) pump motor - Remove connector for Secondary Air Injection (AIR) pump motor -V101-. - Connect VAG1527B voltage tester between terminals 1 and 2 - Initiate output Diagnostic Test Mode (DTM) and activate Secondary Air Injection (AIR) pump relay -J299Repair Manual , 1.8 Liter 4-Cyl. 5V Turbo Fuel Injection & Ignition, Engine Code(s): AMU, Repair Group 24, Fuel preparation, injection LED must light up. VAG 1598/31 testing box Bushing 66

    http://127.0.0.1:8080/audi/servlet/Display?action=Goto&target=_top&type=repair&id... 27/02/2005

    Secondary Air Injection (AIR) system, checking

    Page 19 of 21

    26-44

    If LED does not light up: - Perform the following tests marked with dots: Check wire connection from connector at Secondary Air Injection (AIR) pump motor V101- to Secondary Air Injection (AIR) pump relay -J299- (in relay carrier below cover, left at bulkhead) for open circuit: Electrical Wiring Diagrams, Troubleshooting & Component Locations Check wire connection from connector at Secondary Air Injection (AIR) pump motor V101- to Ground (GND) point in engine compartment, left, for open circuit: Electrical Wiring Diagrams, Troubleshooting & Component Locations If no malfunctions are detected: - Replace Secondary Air Injection (AIR) pump motor -V101-.

    http://127.0.0.1:8080/audi/servlet/Display?action=Goto&target=_top&type=repair&id... 27/02/2005

    Secondary Air Injection (AIR) system, checking

    Page 20 of 21

    26-45

    Secondary air system components, removing and installing


    - Testing secondary air system Repair Manual. 1.8 Liter 4-Cyl. 5V Turbo Fuel Injection & Ignition, Engine Code(s): AMU A- Secondary air pump motor - Remove center section of noise insulation.

    - Disconnect hoses and connectors on secondary air pump - Remove secondary air pump

    http://127.0.0.1:8080/audi/servlet/Display?action=Goto&target=_top&type=repair&id... 27/02/2005

    Secondary Air Injection (AIR) system, checking

    Page 21 of 21

    26-46

    B- Mechanical secondary air valve (combination valve) - Remove engine cover panel.

    - Disconnect vacuum hose -1- and connecting pipe -2- at combination valve. - Unbolt combination valve from bracket -arrows-.

    http://127.0.0.1:8080/audi/servlet/Display?action=Goto&target=_top&type=repair&id... 27/02/2005

    You might also like