Scribd Logo
Upload

Welcome to Scribd!

  • 31 views

    Boss Audio Systems Chaos Ch650 Service Manual: Quick Links

    Uploaded by

    lacho R
    Manual boss

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Boss Audio Systems Chaos Ch650 Service Manual: Quick Links

    Uploaded by

    lacho R
    31 views10 pages
    Manual boss

    Original Title

    643811

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Manual boss

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    31 views10 pages

    Boss Audio Systems Chaos Ch650 Service Manual: Quick Links

    Uploaded by

    lacho R
    Manual boss

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 10

    Manualslib.

    com - Simplified Manuals

    Manuals / Brands / Boss Audio Systems Manuals / Car Amplifier / CHAOS CH650 / Service manual / PDF

    BOSS AUDIO SYSTEMS CHAOS CH650 SERVICE


    MANUAL

    Quick Links
    Specifications
    Circuit Diagram

    Table of Contents
    specifications
    EXPLODED VEIW
    PRINTED CIRCUIT BOARD
    CIRCUIT DIAGRAM
    PARTS LIST
    MODEL: CH650

    SPECIFICATIONS
    Maximum power output (2 Ohms): 250W x 4ch
    RMS power Output: 100W x 4ch
    Bridged Power Output: 500W x 2ch
    Frequency response: 9 - 50KHz
    Harmonic distortion: 0.01%
    S/N Ratio: 130dB
    Power Source Voltage: 14.4V
    Ground: Negative
    Power consumption: 25A(with 125Wx2 rated output)
    External dimensions: 300(W)x65(H)x378(D)mm

    -1-

    Downloaded from www.Manualslib.com manuals search engine


    To engineers in charge of repair or inspection of
    our products.
    Before repair or inspection, make sure to follow the instructions so that customers
    and Engineers in charge of repair or inspection can avoid suffering any risk or injury.

    1. Use specified parts.


    The system uses parts with special safety features against fire and voltage. Use only
    parts with equivalent characteristics when replacing them. The use of unspecified
    parts shall be regarded as remodeling for which we shall not be liable. The onus of
    product liability (PL) shall not be our responsibility in cases where an accident or
    failure is as a result of unspecified parts being used.

    2. Place the parts and wiring back in their original positions after replacement or
    re-wiring. For proper circuit construction, use of insulation tubes, bonding, gaps to
    PCB, etc, is involved. The wiring connection and routing to the PWB are specially
    planned using clamps to keep away from heated and high voltage parts. Ensure that
    they are placed back in their original positions after repair or inspection. If extended
    damage is caused due to negligence during repair, the legal responsibility shall be
    with the repairing company.

    3. Check for safety after repair. Check that the screws, parts and wires are put back
    securely in their original position after repair. Ensure for safety reasons there is no
    possibility of secondary ploblems around the repaired spots. If extended damage is
    caused due to negligence of repair, the legal responsibility shall be with the repairing
    company.

    4. Caution in removal and making wiring connection to the parts for the automobile.
    Disconnect the battery terminal after turning the ignition key off. If wrong wiring
    connections are made with the battery connected, a short circuit and/or fire may occur.
    If extensive damage is caused due to negligence of repair, the legal responsibility
    shall be with the repairing company.

    5. Cautions regarding chips.


    Do not reuse removed chips even when no abnormality is observed in their
    appearance. Always replace them with new ones. (The chip parts include resistors,
    capacitors, diodes, transistors, etc). The negative pole of tantalum capacitors is
    highly susceptible to heat, so use special care when replacing them and check the
    operation afterwards.

    6. Cautions in handling flexible PCB


    Before working with a soldering iron, make sure that the iron tip temperature is
    around 270... Take care not to apply the iron tip repeatedly(more than three times)
    to the same patterns. Also take care not to apply the tip with force.

    7. Turn the unit OFF during disassembly and parts replacement. Recheck all work
    before you apply power to the unit.

    -2-

    Downloaded from www.Manualslib.com manuals search engine


    EXPLODED VEIW

    -3-

    Downloaded from www.Manualslib.com manuals search engine


    PRINTED CIRCUIT BOARD

    -4-

    Downloaded from www.Manualslib.com manuals search engine


    CIRCUIT DIAGRAM 1

    -5-

    Downloaded from www.Manualslib.com manuals search engine


    CIRCUIT DIAGRAM 1

    -6-

    Downloaded from www.Manualslib.com manuals search engine


    PARTS LIST - 1

    -7-

    Downloaded from www.Manualslib.com manuals search engine


    PARTS LIST - 2

    -8-

    Downloaded from www.Manualslib.com manuals search engine


    PARTS LIST - 3

    -9-

    Downloaded from www.Manualslib.com manuals search engine

    You might also like