How To TEST COMPONENTS
How To TEST COMPONENTS
html
You don't have to buy expensive test equipment but you do need it to do the simplest testing and fixing.
Here are the first four things you will need:
Transistor tester
OSCILLOSCOPE tester
MULTIMETERS
There are two types:
DIGITAL and ANALOGUE
A Digital Multimeter has a set of digits on the display and an Analogue Multimeter has a scale
with a pointer (or needle).
You really need both types to cover the number of tests needed for designing and repair-
work. We will discuss how they work, how to use them and some of the differences between
them.
BUYING A MULTIMETER
There are many different types on the market.
The cost is determined by the number of ranges and also the extra features such as diode
tester, buzzer (continuity), transistor tester, high DC current and others.
Since most multimeters are reliable and accurate, buy one with the greatest number of
ranges at the lowest cost.
This article explains the difference between a cheap analogue meter, an expensive analogue
meter and a digital meter. You will then be able to work out which two meters you should
buy.
Before making any measurement you need to know what you are checking. If you are
measuring voltage, select the AC range (10v, 50v, 250v, or 1000v) or DC range (0.5v, 2.5v,
10v, 50v, 250v, or 1000v). If you are measuring resistance, select the Ohms range (x1, x10,
x100, x1k, x10k). If you are measuring current, select the appropriate current range DCmA
0.5mA, 50mA, 500mA. Every multimeter is different however the photo below shows a low
cost meter with the basic ranges.
The most important point to remember is this:
You must select a voltage or current range that is bigger or HIGHER than the maximum
expected value, so the needle does not swing across the scale and hit the "end stop."
If you are using a DMM (Digital Multi Meter), the meter will indicate if the voltage or current
is higher than the selected scale, by showing "OL" - this means "Overload." If you are
measuring resistance such as 1M on the x10 range the "OL" means "Open Loop" and you will
need to change the range. Some meters show "1' on the display when the measurement is
higher than the display will indicate and some flash a set of digits to show over-voltage or
over-current. A "-1" indicates the leads should be reversed for a "positive reading."
If it is an AUTO RANGING meter, it will automatically produce a reading, otherwise the
selector switch must be changed to another range.
Before taking a resistance reading (each time on any of the Ohms scales) you need to "ZERO
SET" the scale, by touching the two probes together and adjust the pot until the needle
reads "0" (swings FULL SCALE). If the pointer does not reach full scale, the batteries need
replacing. Digital multimeters do not need "zero adjustment."
FIXING A MULTIMETER
A multimeter can get "broken" "damaged" and go "faulty."
I don't know why, but eventually they stop working.
It can be something simple like a flat battery, corroded battery contacts, broken switch or
something complex, like the circuitry failing.
Multimeters are so cheap, you can buy a new one for less than $10.00
These meters can have a 10 amp range, transistor tester and measure up to 2 meg ohms.
That's why I suggest buying a $10.00 meter. They are just as good as a $60.00 meter and
the cheapest meters last the longest.
Dropping an analogue meter can cause the hair spring to loop over one of the supports and
the needle will not zero correctly. You will need to open the cover on the movement and
lift the spring off the support with a needle.
A faulty meter can be used in a battery-charger circuit to measure the current or voltage if
that scale is still reading-correctly.
Otherwise keep the leads and throw the meter out. It is too dangerous keeping a meter
that shows an incorrect reading.
MEASURING FREQUENCY
ACA 600uA/6000uA/60mA/600mA/6A/20A
Resistance 600Ω/6kΩ/60kΩ/600kΩ/6MΩ/60MΩ
Frequency 100Hz/1kHz/10kHz/100kHz/1MHz/60MHz
-40°C~1000°C
Temperature
0°F~1832°F
VOLTAGE
Most of the readings you will take with a multimeter will be VOLTAGE readings.
Before taking a reading, you should select the highest range and if the needle does not move up
scale (to the right), you can select another range.
Always switch to the highest range before probing a circuit and keep your fingers away from the
component being tested.
If the meter is Digital, select the highest range or use the auto-ranging feature, by selecting "V."
The meter will automatically produce a result, even if the voltage is AC or DC.
If the meter is not auto-ranging, you will have to select if the voltage is from a DC source
or if the voltage is from an AC source. DC means Direct Current and the voltage is coming
from a battery or supply where the voltage is steady and not changing and AC means Alternating
Current where the voltage is coming from a voltage that is rising and falling.
You can measure the voltage at different points in a circuit by connecting the black probe to
chassis. This is the 0v reference and is commonly called "Chassis" or "Earth" or "Ground" or "0v."
The red lead is called the "measuring lead" or "measuring probe" and it can measure voltages at
any point in a circuit. Sometimes there are "test points" on a circuit and these are wires or loops
designed to hold the tip of the red probe (or a red probe fitted with a mini clip or mini alligator
clip).
You can also measure voltages ACROSS A COMPONENT. In other words, the reading is taken in
PARALLEL with the component. It may be the voltage across a transistor, resistor, capacitor,
diode or coil. In most cases this voltage will be less than the supply voltage.
If you are measuring the voltage in a circuit that has a HIGH IMPEDANCE, the reading will
be inaccurate, up to 90% !!!, if you use a cheap analogue meter.
Here's a simple case.
The circuit below consists of two 1M resistors in series. The voltage at the mid point will be 5v when nothing is
connected to the mid point. But if we use a cheap analogue multimeter set to 10v, the resistance of the meter will be
about 100k, if the meter has a sensitivity of 10k/v and the reading will be incorrect.
Here how it works:
Every meter has a sensitivity. The sensitivity of the meter is the sensitivity of the movement and is the amount of current
required to deflect the needle FULL SCALE.
This current is very small, normally 1/10th of a milliamp and corresponds to a sensitivity of 10k/volt (or 1/30th mA, for a
sensitivity of 30k/v).
If an analogue meter is set to 10v, the internal resistance of the meter will be 100k for a 10k/v movement.
If this multimeter is used to test the following circuit, the reading will be inaccurate.
The reading should be 5v as show in diagram A.
But the analogue multimeter has an internal resistance of 100k and it creates a circuit shown in C.
The top 1M and 100k from the meter create a combined PARALLEL resistance of 90k. This forms a series circuit with the
lower 1M and the meter will read less than 1v
If we measure the voltage across the lower 1M, the 100k meter will form a value of resistance with the lower 1M and it
will read less than 1v
If the multimeter is 30k/v, the readings will be 2v. See how easy it is to get a totally inaccurate reading.
This introduces two new terms:
HIGH IMPEDANCE CIRCUIT and "RESISTORS in SERIES and PARALLEL."
If the reading is taken with a Digital Meter, it will be more accurate as a DMM does not take
any current from the circuit (to activate the meter). In other words it has a very HIGH input
impedance. Most Digital Multimeters have a fixed input resistance (impedance) of 10M - no
matter what scale is selected. That's the reason for choosing a DMM for high impedance
circuits. It also gives a reading that is accurate to about 1%.
MEASURING VOLTAGES IN A CIRCUIT
You can take many voltage-measurements in a circuit. You can measure "across" a component,
or between any point in a circuit and either the positive rail or earth rail (0v rail). In the
following circuit, the 5 most important voltage-measurements are shown. Voltage "A" is across
the electret microphone. It should be between 20mV and 500mV. Voltage "B" should be about
0.6v. Voltage "C" should be about half-rail voltage. This allows the transistor to amplify both
the positive and negative parts of the waveform. Voltage "D" should be about 1-3v. Voltage "E"
should be the battery voltage of 12v.
Current is always measured when the circuit is working (i.e: with power applied).
It is measured IN SERIES with the circuit or component under test.
The easiest way to measure current is to remove the fuse and take a reading across the fuse-
holder. Or remove one lead of the battery or turn the project off, and measure across the
switch.
If this is not possible, you will need to remove one end of a component and measure with the
two probes in the "opening."
Resistors are the easiest things to desolder, but you may have to cut a track in some circuits.
You have to get an "opening" so that a current reading can be taken.
The following diagrams show how to connect the probes to take a CURRENT reading.
Do not measure the current ACROSS a component as this will create a "short-circuit."
The component is designed to drop a certain voltage and when you place the probes across
this component, you are effectively adding a "link" or "jumper" and the voltage at the left-side
of the component will appear on the right-side. This voltage may be too high for the circuit
being supplied and the result will be damage.
Measuring current through a resistor
MEASURING 1 AMP
Most digital multimeters only go to 200mA and most cheap analogue meters only go to
500mA.
But a clever way to measure up to 1 amp is to put 2 cheap analogue meters in parallel and
read the two screens. Just add the combined values and you will be able to read up to 1
amp.
Just another time when a cheap $5.00 analogue meter comes in handy.
MEASURING AC CURRENT
Measuring AC current is very difficult to do because the waveform is rising and falling and when the
waveform is "on and off" such as the DCC waveform in a DCC Model Railway set-up, the actual current
taken by a module will be impossible to measure with a cheap multimeter.
However a simple way to find out the current flowing is to place a 500 ohm pot in the positive line and
connect a LED from the middle pin to one of the outer pins and then connect another LED across the LED
but in the opposite direction. This will only be suitable for a current up to about 50mA.
As you turn the pot from zero ohms, the LEDs will start to come on.
We are NOT measuring the brightness but the point at which the LED detects a voltage of about 3.2v
across the pot. (actually across about half the pot)
Now put the "tester" on a variable power supply and connect a 220R as the load. As you increase the
voltage, one of the LEDs will come on with the same very weak brightness. Now place a DC milliamp meter
in line with the tester and measure the current. The value will be very close to the AC current flowing in
the original circuit.
The same principle can be used to measure higher currents by using a low-resistance resistor and 2 LEDs.
Suppose you have a 10 ohm resistor and LEDs that illuminate at 3.2v
When the current peaks at 320mA, the LEDs will be illuminated with very low brightness, but because the
peak will only be for a very small portion of the cycle, the actual current-flow will not be equal or the same
as 320mA DC current. We are just measuring a PEAK.
You have to be careful when making this type of "tester" to prevent damaging the LEDs. Start with a set of
say 5 resistors in parallel with each value 47 ohms or slightly higher or lower. As you remove each resistor,
the LEDs will start to come ON.
This will let you know that some point in the cycle the current is 320mA.
If it is a square-wave, such as the DCC waveform for Model Railways, the DC current-flow will be very
nearly the same as the AC current measured by this tester.
MEASURING RESISTANCE
Turn a circuit off before measuring resistance.
If any voltage is present, the value of resistance will be incorrect.
In most cases you cannot measure a component while it is in-circuit. This is because
the meter is actually measuring a voltage across a component and calling it a
"resistance." The voltage comes from the battery inside the meter. If any other
voltage is present, the meter will produce a false reading.
If you are measuring the resistance of a component while still "in circuit," (with the
power off) the reading will be lower than the true reading.
1. Do not measure the "resistance of a battery." The resistance of a battery (called the Internal impedance) is not
measured as shown in the diagrams above. It is measured by creating a current-flow and measuring the voltage across
the battery. Placing a multimeter set to resistance (across a battery) will destroy the meter.
2. Do not try to measure the resistance of any voltage or any "supply."
The size of a resistor has nothing to do with its resistance. The size determines the wattage
of the resistor - how much heat it can dissipate without getting too hot.
Every resistor is identified by colour bands on the body, but when the resistor is a surface-
mount device, numbers are used and sometimes letters.
You MUST learn the colour code for resistors and the following table shows all the colours
for the most common resistors from 1/10th of an ohm to 22 Meg ohms for resistors with
5% and 10% tolerance.
If 3rd band is gold, Divide by 10
If 3rd band is silver, Divide by 100
(to get 0.22ohms etc)
Reading 4-band resistors
The most "common" type of resistor has 4 bands and is called the 10% resistor. It now has a
tolerance of 5% but is still called the "10% type" as the colours increase by 20% so that a
resistor can be 10% higher or 10% lower than a particular value and all the resistors
produced in a batch can be used.
The first 3 bands produce the resistance and the fourth band is the "tolerance" band. Gold
= 5%
(Silver =10% but no modern resistors are 10%!! - they are 5% 2% or 1%)
Download the program and save it on your desk-top for future reference:
ColourCode.exe (520KB)
ColourCode.zip (230KB)
ColourCode.rar (180KB)
The letters "R, k and M" take the place of a decimal point.
e.g: 1R0 = 1 ohm 2R2 = 2 point 2 ohms 22R = 22 ohms
2k2 = 2,200 ohms 100k = 100,000 ohms
2M2 = 2,200,000 ohms
HOW TO REMEMBER THE COLOUR CODE:
Each colour has a "number" (or divisor) corresponding to it.
Most of the colours are in the same order as in the spectrum. You can see the spectrum in a
rainbow. It is: ROY G BIV and the colours for resistors are in the same sequence.
black
brown - colour of increasing temperature
red
colour value No of zero's
orange
yellow silver -2 divide by 100
green
blue gold -1 divide by 10
(indigo - that part of the spectrum between blue and violet)
violet black 0 No zeros
gray brown 1 0
white red 2 00
orange 3 ,000 or k
yellow 4 0,000
green 5 00,000
blue 6 M
violet 7
gray 8
white 9
Here are some common ways to remember the colour
code:
Bad Beer Rots Our Young Guts, But Vodka Goes Well
Bright Boys Rave Over Young Girls But Violet Gets Wed
Bad Boys Rave Over Young Girls But Violet Gets Wed
with Gold and Silver.
Reading 5-band resistors:
5-band resistors are easy to read if you remember two simple points. The first three bands
provide the digits in the answer and the 4th band supplies the number of zero's.
A 330k SM resistor
The first two digits represent the two digits in the answer. The third digit represents the
number of zero's you must place after the two digits. The answer will be OHMS. For
example: 334 is written 33 0 000. This is written 330,000 ohms. The comma can be
replaced by the letter "k". The final answer is: 330k.
222 = 22 00 = 2,200 = 2k2
473 = 47 000 = 47,000 = 47k
474 = 47 0000 = 470,000 = 470k
105 = 10 00000 = 1,000,000 = 1M = one million ohms
There is one trick you have to remember. Resistances less than 100 ohms are written: 100,
220, 470. These are 10 and NO zero's = 10 ohms = 10R
or 22 and no zero's = 22R or 47 and no zero's = 47R. Sometimes the resistor is marked:
10, 22 and 47 to prevent a mistake.
Remember:
R = ohms
k = kilo ohms = 1,000 ohms
M = Meg = 1,000,000 ohms
The 3 letters (R, k and M) are put in place of the decimal point. This way you cannot make a mistake
when reading a value of resistance.
Surface Mount CURRENT SENSING Resistors
Many new types of CURRENT SENSING surface-mount resistors are appearing on the market and these
are creating lots of new problems.
Fortunately all resistors are marked with the value of resistance and these resistors are identified in
MILLIOHMS. A miili ohm is one thousandth or an ohm and is written 0.001 when writing a normal
mathematical number.
When written on a surface mount resistor, the letter R indicates the decimal point and it also signifies the
word "OHM" or "OHMS" and one milli-ohm is written R001
Five miiliohms is R005 and one hundred milliohms is R100
Some surface mount resistors have the letter "M" after the value to indicate the resistor has a rating of 1
watt. e.g: R100M These surface-mount resistors are specially-made to withstand a high temperature
and a surface-mount resistor of the same size is normally 250mW or less.
These current-sensing resistors can get extremely hot and the PC board can become burnt or damaged.
When designing a PC board, make the lands very large to dissipate the heat.
Normally a current sensing resistor is below one ohm (1R0) and it is easy to identify them as R100 etc.
You cannot measure the value of a current sensing resistor as the leads of a multimeter have a higher
resistance than the resistor and few multimeters can read values below one ohm.
If the value is not visible, you will have to refer to the circuit.
Before replacing it, work out why it failed.
Generally it gets too hot. Use a larger size and add tiny heatsinks on each end.
Here are some surface=mount current-sense resistors:
THE COMPLETE RANGE OF SM RESISTOR
MARKINGS
Click to see the complete range of SM resistor markings for 3-digit code:
330 is 33 ohms - not 330 ohms 1000 is 100 ohms - not 1000 ohms
0R56 or R56 is
105 is 1 000 000 ohms, or 1M
0.56 ohms
22A is a 165 ohm resistor, 68C is a 49900 ohm (49k9) and 43E a 2740000 (2M74). This marking
scheme applies to 1% resistors only.
A similar arrangement can be used for 2% and 5% tolerance types. The multiplier letters are
identical to 1% ones, but occur before the number code and the following code is used:
Some resistor networks have a "4S" printed on the component. The 4S indicates the
package contains 4 independent resistors that are not wired together inside. The housing
has eight leads as shown in the second image.
Independent resistors have an even number of pins and measuring between each pair will
produce identical values. Resistance between any pair will indicate leakage and may be a
fault. If you know how they are connected, and the value, and you think they are faulty, you
can replace an array with 8 small resistors soldered together in a similar way to the diagrams
below. The network below has an "in house" number and does not identify any values.
WIRE WOUND RESISTOR
A wire wound resistor is also called a POWER RESISTOR. This type of resistor can have a resistance as low as
0.1 ohms (one-tenth of an ohm) or as high as about 10k.
The image shows a 0.68 ohm resistor as the letter "R" represents the DECIMAL POINT and R68 is the same a
.68 and this is 0.68 ohms. The wattage is 9 watts.
This resistor will allow xxx amps to flow. To work out the current, use the formula:
Power = Current x Current x resistance
9 = Current x Current x .68
Divide both sides by 0.68
13.2 = Current x Current
Find the square root of 13.2
Current = 3.6 amps
When 3.6 amps flow through the resistor, the voltage appearing across it will be:
V = current x resistance
= 3.6 x 0.68
= 2.5v and the wattage (heat) loss will be 9 watts.
The purpose of a resistor like this is to stop or reduce "ripple." Ripple is the noise or hum in an
amplifier when the sound is turned up.
There are many reasons why you need to reduce the level of hum and this resistor will remove
ripple as large as 2.5v when 3.6 amps is flowing, provided you have filter electrolytics on both
side of the resistor to assist in removing the ripple.
If the letter "R" is in a different position, the value of resistance would be:
68R = 68Ω
6R8 = 6.8Ω
R68 = 0.68Ω
If you replace the R68 resistor a 6R8 resistor by mistake, the voltage across it will rise to 25v and
if 3.6 amps flows, the wattage will be: 90 watts!!!
The resistor will glow red and burn out.
TESTING A POSISTOR
A Posistor is a resistor that connects in series with the degaussing coil around the picture tube
or Monitor. When cold, it has a very low resistance and a large current flows when the monitor
or TV is switched on. This current heats up the Posistor and the resistance increases. This causes
the current to decrease and any magnetism in the shadow mask is removed. The posistor can
one or two elements and it is kept warm so the resistance remains high. Many Posistors have a
second element inside the case that connects directly to the supply to keep the Positive
Temperature Coefficient resistor high so that the current through the degaussing coil falls to
almost zero. This constant heat eventually destroys the package.
The heavy current that flows when a set is turned ON also causes the posistor to crack and
break and this results in poor purity on the screen - as the shadow mask gradually becomes
magnetic..
Posistors have different resistance values from different manufacturers and must be replaced
with an identical type.
They can be checked for very low resistance when cold but any loose pieces inside the case will
indicate a damaged component.
A "BURNT" RESISTOR - normally and technically called a "burnt-out" resistor.
The resistance of a "burnt" resistor can sometimes be determined by scraping away the outer
coating - if the resistor has a spiral of resistance-material. You may be able to find a spot where
the spiral has been damaged.
Clean the "spot" (burnt section of the spiral) very carefully and make sure you can get a good
contact with the spiral and the tip of your probe. Measure from one lead of the resistor to the
end of the damaged spiral. Then measure from the other lead to the other end of the spiral.
Add the two values and you have an approximate value for the resistor. You can add a small
amount for the damaged section.
This process works very well for damaged wire-wound resistors. They can be pulled apart and
each section of the resistance-wire (nichrome wire) measured and added to get the full
resistance.
There is a third way to determine the value and this requires measuring the voltage drop across
the resistor and the current-flow. By multiplying the two you will get a wattage and this must be
less than the wattage of the resistor being replaced.
A "SHUNT" RESISTOR
A SHUNT RESISTOR is a power-resistor and you will find them in multimeters to provide the CURRENT
READING.
This type of resistor is also called A CURRENT SHUNT (Current Shunt Resistor) or CURRENT SENSE RESISTOR.
You will also find them in many other circuits where the current is required to be measured.
A CURRENT SENSE RESISTOR is always very low resistance so it does not alter the performance of the
circuit.
As current flows though the resistor, a voltage is produced across the resistor and this voltage is measured
by a detecting circuit and the designer of the circuit already knows how much current is flowing for each mV
developed across the resistor.
But, if too much current flows, these resistors can burn-out and it is impossible to work out the value of the
resistor. Mainly because the resistance can be as low as 0.1 ohms.
But there is an easy way to replace the resistor.
You will need a set of resistors and the cheapest way to start is with one ohm resistors (0.25watt).
Place two of them in parallel and connect the project in series with a multimeter set to 10 amp range and
then place a 10 ohm wire-wound resistor in series with the two instruments and a 12v supply.
You know the current should be about 1.2 amps and if the reading on your damaged instrument is reading 3
amps, you will need to place another one-ohm resistor in parallel with the other two. Keep doing this until
the reading on the damaged meter corresponds to the reading on the functioning meter.
You can add 2 or 3 one-ohm resistors in series to get a fine adjustment.
When you have finished, you can work out the value of the combination by realising two resistors in parallel
is equal to 0.5 ohms and 3 is 0.33 ohms and 4 is 0.25 ohms.
You may be able to buy shunt resistors of the required value or maybe use surface mount resistors but you
also have to take into account the size of the original resistor. You must match the size.
MILLI-OHM RESISTORS
Many SHUNT RESISTORS have a very low resistance, mainly because the resistor is measuring a
high current and you don't want a lot of heat to be created by the resistor and you don't want
the voltage you are measuring to reduce in value.
That's why many SHUNT RESISTORS have a resistance in the MILLI-OHM range.
A milliohm is ONE THOUSANDTH OF AN OHM and if one amp is flowing through the resistor,
one-millivolt will be developed across it.
If you go through all the samples below, the same reasoning produces 5mV for a 5 milli-ohm
resistor and one quarter of a milli-volt for a 0m25 resistor. Thus 4 amp through this resistor
produces 1mV.
Because a high current will flow through the resistor and through the tracks, there will be some
degree of heating and these resistors can get warm/hot and even overheat and melt the solder.
They can also go open and that's where your skill comes in . . to replace them with the correct
value and wattage.
TESTING AND MEASURING MILLI-OHM RESISTORS
Very low-ohm resistors can be measured in two ways.
Digital multimeters will measure resistors from 0.1 ohms but the leads add 0.3 ohms to the
reading.
You can double-check the reading by adding a 1 ohm resistor and measuring the milli-ohm
resistor with the 1 ohm and with it removed.
If the milliohm resistor is less than 0.1 ohm, you can place the resistor in series with a
multimeter set to current (1 amp) and add an 8 ohm wire wound resistor in series.
Connect the circuit to a variable power supply and increase the current to exactly 1 amp.
Now measure the voltage across the milli-ohm resistor with a multimeter set to say 2,000mA.
Each mV will represent 1milliohm.
For example, if the reading is 200mV, the resistor is 200milli-ohm (0.2 ohm).
If the reading is 1,000mV (1volt) the resistor will be 1,000milli-ohm (1 ohm)
A 0m25 resistor (shown above) will show 0.25mV on the multimeter.
A 5M0 resistor above will show 5mV on the multimeter.
A R015 resistor will show 15mV on the multimeter.
SAFETY RESISTOR
Finally we come to the use of a resistor as a SAFETY RESISTOR.
Whenever you are testing a circuit, you need to use a supply that will not deliver a high current. This will
prevent things "going up in smoke" and burning the PCB tracks. The easiest is to use "dry cells" (AA) and
even though the motor or output device may not work correctly, you can be sure a short-circuit is not
present.
If you are going to use a 12v battery, you need to include a one-ohm (0.25watt) resistor in series with the
positive lead.
This resistor ill allow 250mA to pass with damage. At 500mA the resistor will get very hot and any current
above this will burn out the resistor.
You will be able to work out how quickly the resistor "goes up in smoke" and compare it to the current
requirement of the circuit.
If you leave the resistor permanently in the positive line, it becomes a SAFETY RESISTOR, but don't forget it
will drop a small voltage and if the circuit takes peaks of current, this resistor can fail.
For the cost of one-cent you can protect a project and make sure it is working before connecting it
permanently to the supply.
FUSIBLE RESISTOR
A fusible resistor is a low value resistor and should be made of non-combustible materials.
The value is chosen so it does not get hot during normal operation but if twice the current
flows, it "burns out."
Sometimes it is housed in a non-combustible sleeve.
If you think it has burnt out for no reason, replace it with a one-ohm resistor (0.25 watt) and feel
its temperature. If it is in a DC line, the voltage across it will be 250mV max.
SUBSTITUTING A RESISTOR
You can get a resistor substitution box for $18.00 plus postage.
I bought one 40 years ago and have only used it ONCE.
Just get a a resistor on jumper leads and if it burns out, you have only lost 10 cents.
When designing a circuit, you may need to go 10% higher or lower to see the effect.
That's why it is best to try a resistor on leads.
FOCUS POTSS
Focus pots quite often get a spot of dirt where the wiper touches the track. Cleaning with spray fixes the bad
focus but if the pot is leaking to chassis from inside the pot (due to the high voltage on the terminals) simply
remove it from the chassis and leave it floating (this will restore the high voltage to the picture tube) or you
can use one from an old chassis.
RESISTORS
Two 1k 0.5watt resistors in parallel produces a 470R 1watt resistor.
Two 1k 0.5watt resistors in series produces a 2k 1watt resistor.
CAPACITORS
Two 100n 100v capacitors in series produces a 50n capacitor @200v
DIODES: Two 1Amp 400v diodes in series produces a 1Amp 800v diode
Two 1Amp 400v diodes in parallel produces a 2Amp 400v diode
ZENER DIODES: Zener diodes can be connected in series to get a higher voltage.
Two 12v zener diodes in series produces a 24v zener.
CONTINUITY
Some multimeters have a "buzzer" that detects when the probes are touching each other or the resistance between the
probes is very LOW. This is called a CONTINUITY TESTER.
You can use the resistance scale "x1" or "x10" to detect low values of resistance.
Set the pointer to "0" (right end of the scale) by touching the probes together and adjusting the "zero ohms" control.
When taking a reading, you will have to decide if a low value of resistance is a short-circuit or an "operating value."
For instance, the cold resistance of a 12v car globe is very low (about 2 ohms) and it increases (about 6 times) to 12 ohms
when hot.
The "resistance of a circuit" may be very low as the electrolytics in the circuit are uncharged. This may not indicate a true
"short-circuit."
The measurement across a diode is not a resistance-value but a "voltage-drop" and that is why the needle swings nearly
full-scale.
Leads and wires and cords have a small resistance and depending on the length of the lead, this small resistance may be
affecting a circuit.
Remember this:
When a circuit takes 1 amp, and the resistance of the leads is 1 ohm, the voltage drop across the leads will be 1v.
That's why a 12v battery supplying a circuit with these leads will have 11v at the circuit.
Note:
Turn off the equipment before making any continuity tests. The presence of even a small voltage (from an electrolytic) can
give a false reading.
You can determine the resistance of a lead very accurately by taking the example above and applying it to your circuit.
If the battery is 12.6v and the voltage across the circuit is 10v, when the current is 2.6 amps, the resistance of the "leads" is
12.6 - 10 = 2.6 R=V/I = 2.6/2.6 = 1ohm. By making the lead shorter or using thicker wire, the resistance will be less and the
voltage on the project will increase.
When taking readings in a circuit that has a number of diodes built-into IC's (Integrated Circuits) and transistors, some
Continuity Testers will beep and give a false reading.
The following circuit has the advantage of providing a beep when a short-circuit is detected but does not detect the small
voltage drop across a diode. This is ideal when testing logic circuits as it is quick and you can listen for the beep while
concentrating on the probe. Using a multimeter is much slower.
CONTINUITY
Some multimeters have a "buzzer" that detects when the probes are touching each other or the resistance between the
probes is very LOW. This is called a CONTINUITY TESTER.
You can use the resistance scale "x1" or "x10" to detect low values of resistance.
Set the pointer to "0" (right end of the scale) by touching the probes together and adjusting the "zero ohms" control.
When taking a reading, you will have to decide if a low value of resistance is a short-circuit or an "operating value."
For instance, the cold resistance of a 12v car globe is very low (about 2 ohms) and it increases (about 6 times) to 12 ohms
when hot.
The "resistance of a circuit" may be very low as the electrolytics in the circuit are uncharged. This may not indicate a true
"short-circuit."
The measurement across a diode is not a resistance-value but a "voltage-drop" and that is why the needle swings nearly
full-scale.
Leads and wires and cords have a small resistance and depending on the length of the lead, this small resistance may be
affecting a circuit.
Remember this:
When a circuit takes 1 amp, and the resistance of the leads is 1 ohm, the voltage drop across the leads will be 1v.
That's why a 12v battery supplying a circuit with these leads will have 11v at the circuit.
Note:
Turn off the equipment before making any continuity tests. The presence of even a small voltage (from an electrolytic) can
give a false reading.
You can determine the resistance of a lead very accurately by taking the example above and applying it to your circuit.
If the battery is 12.6v and the voltage across the circuit is 10v, when the current is 2.6 amps, the resistance of the "leads" is
12.6 - 10 = 2.6 R=V/I = 2.6/2.6 = 1ohm. By making the lead shorter or using thicker wire, the resistance will be less and the
voltage on the project will increase.
When taking readings in a circuit that has a number of diodes built-into IC's (Integrated Circuits) and transistors, some
Continuity Testers will beep and give a false reading.
The following circuit has the advantage of providing a beep when a short-circuit is detected but does not detect the small
voltage drop across a diode. This is ideal when testing logic circuits as it is quick and you can listen for the beep while
concentrating on the probe. Using a multimeter is much slower.
You can build the circuit on Matrix Board and add it to your Test Equipment.
You will need lots of "Test Equipment" and they can be built from circuits in this eBook.
TESTING FUSES, LEADS AND WIRES
All these components come under the heading TESTING for CONTINUITY. Turn off all power to the equipment before testing
for shorts and continuity. Use the low resistance "Ohms Scale" or CONTINUITY range on your multimeter. All fuses, leads
and wires should have a low, very low or zero resistance. This proves they are working.
A BLOWN FUSE
The appearance of a fuse after it has "blown" can tell you a lot about the fault in the circuit.
If the inside of the glass tube (of the fuse) is totally blackened, the fuse has been damaged very quickly. This indicates a very
high current has passed through the fuse.
Depending on the rating of the fuse, (current rating) you will be able to look for components that can pass a high current
when damaged - such as high power transistors, FETs, coils, electrolytics. Before re-connecting the supply, you should test
the "SUPPLY RAILS" for resistance. This is done by measuring them on a low OHMs range in one direction then reverse the
leads to see if the resistance is low in the other direction.
A reading can be very low at the start because electrolytics need time to charge-up and if the reading gradually increases,
the power rail does not have a short. An overload can occur when the supply voltage rises to nearly full voltage, so you
sometimes have to fit a fuse and see how long it takes to "blow."
If the fuse is just slightly damaged, you will need to read the next part of this eBook, to see how and why this happens:
FAST AND SLOW BLOW FUSES
There are many different sizes, shapes and ratings of a fuse. They are all current ratings as a fuse does not have a voltage
rating. Some fuses are designed for cars as they fit into the special fuse holders. A fuse can be designed for 50mA, 100mA,
250mA, 315mA, 500mA, 1Amp, 1.5amp, 2amp, 3amp, 3.15amp 5amp, 10amp, 15amp, 20amp, 25amp, 30amp, 35amp,
50amp and higher.
Some fuses are fast-blow and some are slow-blow.
A "normal" fuse consists of a length of thin wire. Or it may be a loop of wire that is thin near the middle of the fuse. This is
the section that will "burn-out."
A "normal" fuse is a fast-blow fuse. For instance, a 1amp fuse will remain intact when up to 1.25 amp flows. When a circuit
is turned on, it may take 2-3 amps for a very short period of time and a normal 1 amp fuse will get very hot and the wire will
stretch but not "burn-out." You can see the wire move when the supply turns on.
If the current increases to 2amps, the fuse will still remain intact. It needs about 3 amp to heat up the wire to red-hot and
burn out.
If the current increases to 5 amp, the wire VOLATILISES (burns-out) and deposits carbon-black on the inside of the glass
tube.
A slow-blow fuse uses a slightly thicker piece of wire and the fuse is made of two pieces of wire joined in the middle with a
dob of low-temperature solder. Sometimes one of the pieces of wire is a spring and when the current rises to 2.5 amp, the
heat generated in the wire melts the solder and the two pieces of wire "spring apart."
A slow-blow fuse will allow a higher current-surge to pass through the fuse and the wire will not heat up and sag.
Thus the fuse is not gradually being damaged and it will remain in a perfect state for a long period of time.
A fuse does not protect electronic equipment from failing. It acts AFTER the equipment has failed.
It will then protect a power supply from delivering a high current to a circuit that has failed.
If a slow-blow fuse has melted the solder, it could be due to a slight overload, slight weakening of the fuse over a period of
time or the current-rating may be too low.
You can try another fuse to see what happens.
You can replace a fast-acting fuse (normal fuse) with a slow blow if the fast-acting fuse has been replaced a few times due to
deterioration when the equipment is turned on.
But you cannot replace a slow-blow fuse with a fast acting fuse as it will be damaged slightly each time the equipment is
turned on and eventually fail.
100mA FUSES
Fuses below about 100mA are very hard to make and very unreliable.
Many circuits take a high current when turned to charge the electrolytics and a 100mA (or 50mA or 63mA fuse) will bow
and stretch and change shape, every time the equipment is turned ON.
Eventually it will break, due to it heating-up and stretching.
To produce a reliable fuse below 100mA, some manufacturers have placed a resistor inside the fuse and connected it to a
spring. One end of the resistor is soldered to a wire with low-temperature metal and when the resistor gets hot, the metal
softens and the spring pulls the resistor away from the wire.
Quite often you can heat up the metal and connect the wire and the fuse is perfect.
This type of fuse is called a DELAY fuse and the current rating is shown on the end-cap.
The value of the resistor determines the current rating.
There is a small voltage across this type of fuse and it means the circuit sees a slightly lower voltage than the supply
voltage.
The third photo shows the pot of solder or low-temp metal and a wire connected to a spring. The heat generated in the
wire is passed to the solder and it softens. The spring pulls the two components apart. You can smash the glass and set up
the fuse in the two fuse-holders and repair the fuse while you wait for a new fuse to arrive.
TESTING COILS, INDUCTORS and YOKES
Coils, inductors, chokes and yokes are just coils (turns) of wire. The wire may be wrapped around a core
made of iron or ferrite.
It is labeled "L" on a circuit board.
You can test this component for continuity between the ends of the winding and also make sure there is no
continuity between the winding and the core.
The winding can be less than one ohm, or greater than 100 ohms. A coil of wire is also called an INDUCTOR
and it might look like a very simple component, but it can operate in a very complex way.
The way it works is a discussion for another eBook. It is important to understand the turns are insulated but
a slight fracture in the insulation can cause two turns to touch each other and this is called a "SHORTED
TURN" or you can say the inductor has "SHORTED TURNS."
When this happens, the inductor allows the circuit to draw MORE CURRENT. This causes the fuse to "blow."
The quickest way to check an inductor is to replace it, but if you want to measure the inductance, you can
use an INDUCTANCE METER. You can then compare the inductance with a known good component.
An inductor with a shorted turn will have a very low or zero inductance, however you may not be able to
detect the fault when it is not working in a circuit as the fault may be created by a high voltage generated
between two of the turns.
Faulty yokes (both horizontal and vertical windings) can cause the picture to reduce in size and/or bend or
produce a single horizontal line.
A TV or monitor screen is the best piece of Test Equipment as it has identified the fault. It is pointless trying
to test the windings further as you will not be able to test them under full operating conditions. The fault
may not show up when a low voltage (test voltage) is applied.
MEASURING AND TESTING INDUCTORS
Inductors are measured with an INDUCTANCE METER but the value of some inductors is very small and some Inductance
Meters do not give an accurate reading.
The solution is to measure a larger inductor and note the reading. Now put the two inductors in SERIES and the values ADD
UP - just like resistors in SERIES. This way you can measure very small inductors. VERY CLEVER!
An inductor is basically a coil of wire. It may be thick or thin wire. The value of the inductor is a combination of the number
of turns and the material on which the wire is wound.
The value of an inductor does not change over say a period of 20 years but it can go faulty by the enamel cracking and two
turns touching. This can also be due to the difference in voltage between the two turns creating a spark between the turns
and creating a "short."
When you test it, the high voltage is not present and it will test ok.
You may not think a few turns of wire will have any effect on improving a circuit, but spikes are very high frequency and the
inductor will have a very big effect on reducing them.
An inductor (say 100uH) can be produced in many different sizes and the thickness of the wire will be important as it
determines the current that can flow through the inductor.
The term "inductor" also includes those with two or more windings and these components are called TRANSFORMERS.
These devices can get "shorts" and "leaks" between the windings and sparks can be seen between the windings. These
sparks do not occur when you are testing them on test-equipment so the only way to guarantee success is to replace it with
an identical replacement.
TESTING SWITCHES and RELAYS
Switches and relays have contacts that open and close mechanically and you can test them for CONTINUITY.
However these components can become intermittent due to dirt or pitting of the surface of the contacts due
to arcing as the switch is opened.
It is best to test these items when the operating voltage and current is present as they quite often fail due to
the arcing. A switch can work 49 times then fail on each 50th operation. The same with a relay. It can fail one
time in 50 due to CONTACT WEAR.
If the contacts do not touch each other with a large amount of force and with a large amount of the metal
touching, the current flowing through the contacts will create HEAT and this will damage the metal and
sometimes reduce the pressure holding the contact together.
This causes more arcing and eventually the switch heats up and starts to burn. Switches are the biggest
causes of fire in electrical equipment and households.
2. An electronic relay (Solid State Relay) does not have a winding. It works on the principle of an opto-
coupler and uses a LED and Light Activated SCR or Opto-TRIAC to produce a low resistance on the output.
The two pins that energise the relay (the two input pins) must be connected to 5v (or 12v) around the
correct way as the voltage is driving a LED (with series resistor). The LED illuminates and activates a light-
sensitive device.
In most cases you do not know what is inside a Solid State Relay and two things can fail.
The LED can be damaged and the OPTO TRIAC may have failed.
Firstly you have to make sure if the SSR is the faulty item.
You can replace with another of the same type but if this is not possible, you can make one of the circuits above and see if
closing the output terminals will allow the project to operate.
The next test is to measure the voltage across the input.
If it is between 2v and 4v, the LED is possibly working.
If it is above 5v, the SSR may have an internal resistor.
You will then have to measure the current entering the input terminals. This current will be between 7mA and 25mA.
You also bridge across the output terminals to determine if the project is correctly connected to the SSR.
All this requires CARE as the output terminals may be live to the mains, while the input terminals are electrically isolated
from the output with an SSR that is optically connected between input and output.
TESTING REED SWITCHES
A reed switch is generally contained in a long glass tube:
A wire or lead comes out each end for soldering to the reed switch to the project. The two "blades"
inside the switch are made from a material that can be magnetised but does not retain its
magnetism. This effect is called "temporally magnetised" (not permanently magnetised) and really
only "passes" magnetism from one end to the other when in the presence of a magnet. One of the
blades is made of a soft material and it will bend very easily. The other one is much stiffer.
When a magnet is placed under the two blades (or on top), the magnetism from the magnet is passed to the two blades
(INDUCTION or MUTUAL INDUCTION - commonly called INDUCED) and it produces a very weak magnet (in the blade) that is
identical to the powerful magnet as far as the position of the north and south poles are concerned). Initially it produces a N-
S and N-S set of poles and this makes the two blades click together because the top blade will be South at the contact and
the bottom blade will be North.
When the two blades click together the magnetism runs through the two blades and keeps them together. The two blades
attract and the switch is closed. When the magnet is removed, the magnetism in the two blades ceases and the two blades
move apart.
Since there is a very small amount of movement in the top blade, this switch has a limited number of operations. Eventually
it will fail. It is a mechanical device and is not suited for detecting a spinning shaft as 100,000 revolutions will very quickly
weaken the switch.
If the switch does not make contact or remains closed, the moveable blade can be cracked or broken. This can be very hard
to see. So replace the switch.
LATCHING REED SWITCH
A "normal" reed switch can be converted into a LATCHING REED SWITCH by carefully placing a magnet below the switch
and moving it away so the two blades open. Now move it slightly closer but do not allow the blades to close.
This is called putting a "SET" on the switch and the two blades will have a small magnetic effect "induced" in them but not
enough to close the contacts:
Now bring a strong magnet up to the reed switch on the other side of the glass tube with the north
pole above the north of the lower magnet. This effect will increase the INDUCED MAGNETISM in the
blades and close the contacts:
Remove the top magnet and the lower magnet will induce enough magnetism into the blades to keep them closed:
Now bring the upper magnet near the reed switch with the south pole above the north pole of the lower magnet. (In other
words: AROUND THE OTHER WAY) This will have the effect of reducing the induced magnetism in the blades and a point will
be reached when the two contacts will separate:
Remove the top magnet and the switch will remain separated because the lower magnet will
not have sufficient influence on the blades to close the contact:
CAPACITORS
Capacitors are one of the most difficult things to test. That's because they don't give a reading on a
multimeter and their value can range from 1p to 100,000u.
A faulty capacitor may be "open" when measured with a multimeter, and a good capacitor will also be
"open."
You need a piece of test equipment called a CAPACITANCE METER to measure the value of a capacitor.
HOW A CAPACITOR WORKS
There are two ways to describe how a capacitor works. Both are correct and you have to
combine them to get a full picture.
A capacitor has INFINITE resistance between one lead and the other.
This means no current flows through a capacitor. But it works in another way.
Suppose you have a strong magnet on one side of a door and a piece of metal on the other. By
sliding the magnet up and down the door, the metal rises and falls.
The metal can be connected to a pump and you can pump water by sliding the magnet up and
down.
A capacitor works in exactly the same way.
If you raise a voltage on one lead of a capacitor, the other lead will rise to the same voltage. This
needs more explaining - we are keeping the discussion simple.
It works just like the magnetic field of the magnet through a door.
The next concept is this:
Capacitors are equivalent to a tiny rechargeable battery.
They store energy when the supply-voltage is present and release it when the supply drops.
These two concepts can be used in many ways and that's why capacitors perform tasks such as
filtering, time-delays, passing a signal from one stage to another and create many different
effects in a circuit.
CAPACITOR VALUES
The basic unit of capacitance is the FARAD. (C) This is the value used in all equations, but it is a
very large value. A one FARAD capacitor would be the size of a car if made with plates and
paper. Most electronic circuits use capacitors with smaller values such as 1p to 1,000u. 1p is
about equal to two parallel wires 2cm long. 1p is one picofarad.
The easiest way to understand capacitor values is to start with a value of 1u. This is one
microfarad and is one-millionth of a Farad. A 1 microfarad capacitor is about 1cm long and the
diagram shows a 1u electrolytic.
Recapping:
1p = 1 picofarad. 1,000p = 1n ( 1 nanofarad)
1,000n = 1u (1 microfarad)
1,000u = 1millifarad
1,000,000u = 1 FARAD.
Examples:
All ceramic capacitors are marked in "p" (puff")
A ceramic with 22 is 22p = 22 picofarad
A ceramic with 47 is 47p = 47 picofarad
A ceramic with 470 is 470p = 470 picofarad
A ceramic with 471 is 470p = 470 picofarad
A ceramic with 102 is 1,000p = 1n
A ceramic with 223 is 22,000p = 22n
A ceramic with 104 is 100,000p = 100n = 0.1u
TYPES OF CAPACITOR
For testing purposes, there are two types of capacitor.
Capacitors from 1p to 100n are non-polar and can be inserted into a circuit around either
way.
Capacitors from 1u to 100,000u are electrolytics and are polarised. They must be fitted
so the positive lead goes to the supply voltage and the negative lead goes to ground (or
earth).
There are many different sizes, shapes and types of capacitor. They are all the same.
They consist of two plates with an insulating material between. The two plates can be
stacked in layers or rolled together.
The important factor is the insulating material. It must be very thin to keep things small.
This gives the capacitor its VOLTAGE RATING.
If a capacitor sees a voltage higher than its rating, the voltage will "jump through" the
insulating material or around it.
If this happens, a carbon deposit is left behind and the capacitor becomes "leaky" or
very low resistance, as carbon is conductive.
CERAMIC CAPACITORS
Nearly all small capacitors are ceramic capacitors as this material is cheap and the
capacitor can be made in very thin layers to produced a high capacitance for the size of
the component. This is especially true for surface-mount capacitors.
All capacitors are marked with a value and the basic unit is: "p" for "puff" However NO
surface mount capacitors are marked and they are very difficult to test.
VALUE WRITTEN
ON
Value THE
COMPONENT:
0.1p 0p1
0.22p 0p22
0.47p 0p47
1.0p 1p0
2.2p 2p2
4.7p 4p7
5.6p 5p6
8.2p 8p2
10p 10 or 10p
22p 22 or 22p
47p 47 or 47p
56p 56 or 56p
100p 100 on 101
220p 220 or 221
470p 470 or 471
560p 560 or 561
820p 820 or 821
1,000p (1n) 102
2200p (2n2) 222
4700p (4n7) 472
8200p (8n2) 822
10n 103
22n 223
47n 473
100n 104
220n 224
470n 474
1u 105
POLYESTER, POLYCARBONATE, POLYSTYRENE, MYLAR, METALLISED POLYESTER,
("POLY"), MICA and other types of CAPACITOR
There are many types of capacitor and they are chosen for their reliability, stability,
temperate-range and cost.
For testing and repair work, they are all the same. Simply replace with exactly the same
type and value.
Capacitor Colour Code Table
Temperature
Digit Digit Multiplier Tolerance Tolerance
Colour Coefficient
A B D (T) > 10pf (T) < 10pf
(TC)
Black 0 0 x1 ± 20% ± 2.0pF
Violet 7 7 -750x10-6
Electrolytics are available in 1u, 2u2 3u3 4u7 10u, 22u, 47u, 100u, 220u, 330u, 470u, 1,000u,
2,200u, 3,300u, 4,700u, 10,000u and higher.
The "voltage" or "working voltage" can be: 3.3v, 10v, 16v, 25v, 63v, 100v, 200v and higher.
There is also another important factor that is rarely covered in text books. It is RIPPLE
FACTOR.
This is the amount of current that can enter and leave an electrolytic. This current heats up
the electrolytic and that is why some electrolytics are much larger than others, even though
the capacitance and voltage-ratings are the same.
If you replace an electrolytic with a "miniature" version, it will heat up and have a very short
life. This is especially important in power supplies where current (energy) is constantly
entering and exiting the electrolytic as its main purpose is to provide a smooth output from a
set of diodes that delivers "pulsing DC." (see "Power Diodes")
PARALLEL and SERIES CAPACITORS
Capacitors can be connected in PARALLEL and/or SERIES for a number of reasons.
1. If you do not have the exact value, two or more connected in parallel or
series can produce the value you need.
2. Capacitors connected in series will produce one with a higher voltage
rating.
3. Capacitors connected in parallel will produce a larger-value capacitance.
You need to look at the circuit of your amplifier. The two 2,200u electrolytics are possibly
connected as shown in the circuit above and you will notice they are joined to produce a
positive rail and a negative rail with zero (called earth) in the centre.
This forms two different circuits with the top electrolytic filtering the positive rail and the
bottom electro filtering the negative rail. They must be connected to the zero volts rail.
A single 10,000u cannot be connected to the 0v rail and cannot be substituted for the two
electro's.
You can easily determine of the two electro's are connected as shown above.
Test the positive terminal of each electro by placing the negative of the meter on the
chassis.
If the positive of one electro have zero volts, it will be the lower electro in the diagram
above. The negative terminal of the electro will have a minus voltage on it.
RIPPLE CURRENT
When an electrolytic is in a power supply, the voltage entering the electrolytic is rising and falling. This is
called UNFILTERED DC. This voltage is rising to the peak and falling to zero, either 100 or 120 times per
second. The electrolytic charges and this rising and falling voltage "disappears from view" because the
electrolytic stores the maximum voltage and the diode on the power supply prevents the voltage going
back into the "mains."
After a while, the incoming voltage only has a tiny effect on charging the electrolytic a few millivolts on
each cycle to replace the tiny amount of charge lost in the electrolytic due to leakage.
But when you take current from the power supply, the incoming voltage will deliver this current during the
time when it is as high as the voltage to are getting from the power supply, but when it is falling, the
electrolytic delivers the energy.
The electrolytic is not as "strong" as the incoming energy and that's why the output voltage drops a few
volts on each half cycle.
This means current is entering and leaving the electrolytic and the electrolytic has a very small internal
resistance.
By simple ohm's law, the heat generated inside the electro is determined by I2R and this heats the electro.
You can get small, medium and large electrolytics with exactly the same capacity and voltage rating.
The only difference is the temperature rise (and the ripple factor - discussed below). A small electro will
heat up to a higher temperature.
It is impossible to predict what will happen so you need to fit the smallest and cover it. Fell the temp after
an hour. Then fit the others and compare your results.
Testing 1,000u electrolytics shows they all have the same 80milliohm internal impedance, so it is just the
heat dissipation from the can that will reduce the temperature rise.
VOLTAGE RATING OF CAPACITOR
Capacitors have a voltage rating, stated as WV for working voltage, or WVDC. This
specifies the maximum voltage that can be applied across the capacitor without
puncturing the dielectric. Voltage ratings for "poly," mica and ceramic capacitors are
typically 50v to 500 VDC. Ceramic capacitors with ratings of 1kv to 5kv are also
available. Electrolytic capacitors are commonly available in 6v, 10v 16v, 25v, 50v, 100v,
150v, and 450v ratings.
SAFETY
A capacitor can store a charge for a period of time after the equipment is turned off.
High voltage electrolytic caps can pose a safety hazard. These capacitors are in power
supplies and some have a resistor across them, called a bleed resistor, to discharge
the cap after power is switched off.
If a bleed resistor is not present the cap can retain a charge after the equipment is
unplugged.
How to discharge a capacitor
Do not use a screwdriver to short between the terminals as this will damage the
capacitor internally and the screwdriver.
Use a 1k 1 watt or 3watt or 5watt resistor on jumper leads (or held with pliers) and
keep them connected for up to 15 seconds to fully discharge the electro. You can even
go as low as 100 ohms or 10 ohms for a 25v or 35v electrolytic and watch the spark.
Then test it with a voltmeter to make sure all the energy has been removed.
Before testing any capacitors, especially electrolytics, you should look to see if any are
damaged, overheated or leaking. Swelling at the top of an electrolytic indicates
heating (and pressure inside the case) and will result in drying out of the electrolyte.
Any hot or warm electrolytic indicates leakage and ceramic capacitors with portions
missing indicates something has gone wrong (such as it being "blown apart").
You can test capacitors in-circuit for short-circuits. Use the x1 ohms range.
To test a capacitor for leakage, you need to remove it or at least one lead must be
removed. Use the x10k range on an analogue or digital multimeter.
For values above 1u you can determine if the capacitor is charging by using an
analogue meter. The needle will initially move across the scale to indicate the cap is
charging, then go to "no deflection." Any permanent deflection of the needle will
indicate leakage.
You can reverse the probes to see if the needle moves in the opposite direction. This
indicates it has been charged. Values below 1u will not respond to charging and the
needle will not deflect.
This does not work with a digital meter as the resistance range does not output any
current and the electrolytic does not charge.
Rather than spending money on a capacitance meter, it is cheaper to replace any
suspect capacitor or electrolytic.
Capacitors can produce very unusual faults and no piece of test equipment is going to
detect the problem.
In most cases, it is a simple matter to solder another capacitor across the suspect
component and view or listen to the result.
This saves all the worry of removing the component and testing it with equipment
that cannot possibly give you an accurate reading when the full voltage and current is
not present.
It is complete madness to even think of testing critical components such as capacitors,
with TEST EQUIPMENT. You are fooling yourself. If the Test Equipment says the
component is ok, you will look somewhere else and waste a lot of time.
FINDING THE VALUE OF A CAPACITOR
If you want to find the value of a surface-mount capacitor or one where the markings
have been removed, you will need a CAPACITANCE METER. Here is a simple circuit
that can be added to your meter to read capacitor values from 10p to 10u.
The full article can be found HERE.
You can get a kit or a ready-made piece of test gear called CAPACITOR SUBSTITUTION
BOX and also RESISTOR SUBSTITUTION BOX.
I bought one of each 30 years ago and I have only used them ONCE.
They appear to be very handy but when you are testing a circuit, you want the
component next to the other parts.
It is just as easy to pick the component you need from your junk box and connect it to
the circuit via jumper leads. If the resistor burns out, you can throw it away.
REPLACING A CAPACITOR
Always replace a capacitor with the exact same type.
A capacitor may be slightly important in a circuit or it might be extremely critical.
A manufacturer may have taken years to select the right type of capacitor due to previous failures.
A capacitor just doesn't have a "value of capacitance."
It may also has an effect called "tightening of the rails."
In other words, a capacitor has the ability to react quickly and either absorb or deliver energy to
prevent spikes or fluctuations on the rail.
This is due to the way it is constructed. Some capacitors are simply plates of metal film while others are
wound in a coil. Some capacitors are large while others are small.
They all react differently when the voltage fluctuates.
Not only this, but some capacitors are very stable and all these features go into the decision for the
type of capacitor to use.
You can completely destroy the operation of a circuit by selecting the wrong type of capacitor.
No capacitor is perfect and when it gets charged or discharged, it appears to have a small value of
resistance in series with the value of capacitance. This is known as "ESR" and stands for EQUIVALENT
SERIES RESISTANCE. This effectively makes the capacitor slightly slower to charge and discharge.
We cannot go into the theory on selecting a capacitor as it would be larger than this eBook so the only
solution is to replace a capacitor with an identical type.
However if you get more than one repair with identical faults, you should ask other technicians if the
original capacitor comes from a faulty batch.
The author has fixed TV's and fax machines where the capacitors have been inferior and alternate
types have solved the problem.
Some capacitor are suitable for high frequencies, others for low frequencies.
With high frequency circuits, you cannot substitute a capacitor by connecting it to long jumper leads.
The capacitor MUST be soldered directly into the circuit.
DECOUPLING CAPACITORS
A Decoupling Capacitor can severe one, two or three functions. You need to think of a decoupling
capacitor as a miniature battery with the ability to deliver a brief pulse of energy when ever the line-
voltage drops and also absorb a brief pulse of energy when ever the line voltage rises (or spikes).
Decoupling capacitor can range from 100n to 1,000u.
100n capacitors are designed to absorb spikes and also have the effect of tightening-up the rails for high
frequencies. They have no effect on low frequencies such as audio frequencies.
These capacitors are generally ceramic and have very low internal impedance and thus they can operate
at high frequencies.
Capacitors above about 10u are used for decoupling and these are nearly always electrolytics.
Decoupling means "tightening-up the power rails." The electrolytic acts just like a miniature rechargeable
battery, supplying a small number of components in a circuit with a smooth and stable voltage.
The electrolytic is usually fed from a dropper resistor and this resistor charges the electrolytic and adds
to the ability of the electrolytic to create a "separate power supply."
These two components help remove spikes as an electrolytic cannot remove spikes if connected directly
to the supply rails - it's internal impedance is high and the spikes are not absorbed.
Decoupling capacitors are very difficult to test.
They rarely fail but if a project is suffering from unknown glitches and spikes, it is best to simply add
more 100n decoupling caps on the underside of the board and replace all electrolytics.
Some small electrolytics will dry out due to faulty manufacture and simply replacing every one on a
board will solve the problem.
Some of the functions of a decoupling capacitor are:
Removing ripple - hum or buzz in the background of an amplifier
Removing glitches or spikes.
Separating one stage from another to reduce or remove MOTORBOATING - a low frequency sound due
to the output putting a pulse on the power rails that is picked up by the pre-amplifier section and
amplified.
TESTING DIODES
Diodes can have 4 different faults.
1. Open circuit in both directions.
2. Low resistance in both directions.
3. Leaky.
4. Breakdown under load.
TESTING A DIODE ON AN ANALOGUE METER
Testing a diode with an Analogue Multimeter can be done on any of the resistance ranges. [The high
resistance range is best - it sometimes has a high voltage battery for this range but this does not affect
our testing]
There are two things you must remember.
1. When the diode is measured in one direction, the needle will not move at all. The technical term for
this is the diode is reverse biased. It will not allow any current to flow. Thus the needle will not move.
When the diode is connected around the other way, the needle will swing to the right (move up scale) to
about 80% of the scale. This position represents the voltage drop across the junction of the diode and is
NOT a resistance value. If you change the resistance range, the needle will move to a slightly different
position due to the resistances inside the meter. The technical term for this is the diode is forward
biased. This indicates the diode is not faulty.
The needle will swing to a slightly different position for a "normal diode" compared to a Schottky diode.
This is due to the different junction voltage drops.
However we are only testing the diode at very low voltage and it may break-down when fitted to a
circuit due to a higher voltage being present or due to a high current flowing.
2. The leads of an Analogue Multimeter have the positive of the battery connected to the black probe
and the readings of a "good diode" are shown in the following two diagrams:
The diode is REVERSE BIASED in the The diode is FORWARD BIASED in the
diagram above and diodes not conduct. diagram above and it conducts
TESTING A DIODE ON A DIGITAL METER
Testing a diode with a Digital Meter must be done on the "DIODE" setting as
a digital meter does not deliver a current through the probes on some of
the resistance settings and will not produce an accurate reading.
The best thing to do with a "suspect" diode is to replace it. This is because a diode has a number of
characteristics that cannot be tested with simple equipment. Some diodes have a fast recovery for use in
high frequency circuits. They conduct very quickly and turn off very quickly so the waveform is processed
accurately and efficiently.
If the diode is replaced with an ordinary diode, it will heat up as does not have the high-speed
characteristic.
Other diodes have a low drop across them and if an ordinary is used, it will heat up.
Most diodes fail by going: SHORT-CIRCUIT. This can be detected by a low resistance (x1 or x10 Ohms
range) in both directions.
A diode can also go OPEN CIRCUIT. To locate this fault, place an identical diode across the diode being
tested.
A leaky diode can be detected by a low reading in one direction and a slight reading the other direction.
However this type of fault can only be detected when the circuit is working. The output of the circuit will
be low and sometimes the diode heats up (more than normal).
A diode can go open under full load conditions and perform intermittently.
Diodes come in pairs in surface-mount packages and 4 diodes can be found in a bridge.
They are also available in pairs that look like a 3-leaded transistor.
The line on the end of the body of a diode indicates the cathode and you cannot say "this is the positive
lead." The correct way to describe the leads is to say the "cathode lead." The other lead is the anode. The
cathode is defined as the electrode (or lead) through which an electric current flows out of a device.
The following diagrams show different types of diodes:
POWER DIODES
To understand how a power diode works, we need to describe a few things. This has NEVER been described
before, so read carefully.
The 240v AC (called the "mains") consists of two wires, one is called the ACTIVE and the other is NEUTRAL.
Suppose you touch both wires. You will get a shock. The neutral is connected to an earth wire (or rod driven
into the ground or connected to a water pipe) at the point where the electricity enters the premises and you
do not get a shock from the NEUTRAL.
But the voltage on the active is rising to +345v then goes to -345v at the rate of 50 times per second (for a
complete cycle).
345v is the peak voltage of 240v. You never get a 240v shock. (It is a 345v shock.)
In other words, if you touch the two wires at a particular instant, you would get a POSITIVE 345v shock and
at another instant you would get a negative 345v shock. This is shown in the diagram below.
We now transfer this concept to the output of a transformer. The diagram shows an AC waveform on the
output of the secondary.
This voltage is rising 15v higher than the bottom lead then it is 15v LOWER than the bottom lead. The
bottom lead is called "zero volts." You have to say one lead or wire is not "rising and falling" as you need a
"reference" or starting-point" or "zero point" for voltage measurements.
The diode only conducts when the voltage is "above zero" (actually when it is 0.7v above zero) and does not
conduct (at all) when the voltage goes below zero.
This is shown on the output of the Power Diode. Only the positive peaks or the positive parts of the
waveform appear on the output and this is called "pulsing DC." This is called "half-wave" and is not used in a
power supply. We have used it to describe how the diode works. The electrolytics charge during the peaks
and deliver energy when the diode is not delivering current. This is how the output becomes a steady DC
voltage.
Power supplies use FULL WAVE rectification and the other half of the AC waveform is delivered to the output
(and fills in the "gaps") and appears as shown in "A."
ONE FAULTY DIODE
One diode in a bridge can go open (any of the 4 diodes will produce the same effect) and produce an output
voltage that can be slightly lower than the original voltage. The actual "voltage-drop" will depend on the
current taken by the circuit and the ability of the transformer to produce the required voltage and current
during half-wave operation. The voltage during each half cycle (when none of the diodes is delivering any
energy to the circuit) is maintained by the electrolytic and its size (relative to the current taken by the circuit)
will determine the size of the ripple that will result when the diode fails. The ripple will be 100 to 1,000
times greater after the failure of a diode, depending on the value of the filter capacitor.
To locate the faulty diode, simply get a diode and place it across each of the diodes in the bridge (in turn)
when the circuit is working.
For a bridge rectifier, the ripple-frequency will be twice the mains frequency and its ripple will be very small
if the electrolytic is the correct value. When a diode fails, the ripple-frequency will be equal to mains-
frequency and the amplitude will increase considerably. You may even hear background hum from audio
equipment.
If you cannot find a faulty diode, the filter capacitor will be at fault. Turn off the equipment and connect an
electrolytic across the filter capacitor via jumper leads. Turn the power ON and see if the hum has reduced.
DAMPER DIODES
A damper diode is a diode that detects a high voltage and SQUELCHES IT (reduces it -
removes it). The signal that it squelches is a voltage that is in the opposite direction to
the "supply voltage" and is produced by the collapsing of a magnetic field. Whenever a
magnetic filed collapses, it produces a voltage in the winding that is opposite to the
supply voltage and can be much higher. This is the principle of a flyback circuit or EHT
circuit. The high voltage comes from the transformer.
The diode is placed so that the signal passes through it and less than 0.5v appears
across it.
A damper diode can be placed across the coil of a relay, incorporated into a transistor
or FET or placed across a winding of a flyback transformer to protect the driving
transistor or FET.
It can also be called a "Reverse-Voltage Protection Diode," "Spike Suppression Diode,"
or "Voltage Clamp Diode."
The main characteristic of a Damper Diode is HIGH SPEED so it can detect the spike
and absorb the energy.
It does not have to be a high-voltage diode as the high voltage in the circuit is being
absorbed by the diode.
SILICON, GERMANIUM AND SCHOTTKY DIODES
When testing a diode with an analogue meter, you will get a low reading in one direction and a high (or NO
READING) in the other direction. When reading in the LOW direction, the needle will swing nearly full scale
and the reading is not a resistance-value but a reflection of the characteristic voltage drop across the
junction of the diode. As we mentioned before, a resistance reading is really a voltage reading and the meter
is measuring the voltage of the battery minus the voltage-drop across the diode.
Since Silicon, Germanium and Schottky Diodes have slightly different characteristic voltage drops across the
junction, you will get a slightly different reading on the scale. This does not represent one diode being better
than the other or capable of handling a higher current or any other feature.
The quickest, easiest and cheapest way to find, fix and solve a problem caused by a faulty diode is to replace
it.
There is no piece of test equipment capable of testing a diode fully, and the circuit you are working on is
actually the best piece of test equipment as it is identifying the fault UNDER LOAD.
Only very simple tests can be done with a multimeter and it is best to check a diode with an ANALOGUE
MULTIMETER as it outputs a higher current though the diode and produces a more-reliable result.
A Digital meter can produce false readings as it does not apply enough current to activate the junction.
Fortunately almost every digital multimeter has a diode test mode. Using this, a silicon diode should read a
voltage drop between 0.5v to 0.8v in the forward direction and open in the reverse direction. For a
germanium diode, the reading will be lower, around 0.2v - 0.4v in the forward direction. A bad diode will
read zero volts in both directions.
REPLACING A DIODE
It is alway best to replace a diode with the same type but quite often this is not
possible. Many diodes have unusual markings or colours or "in-house" letters.
This is only a general guide because many diodes have special features, especially
when used in high-frequency circuits.
However if you are desperate to get a piece of equipment working, here are the steps:
Determine if the diode is a signal diode, power diode, or zener diode.
For a signal diode, try 1N4148.
For a power diode (1 amp) try 1N4004. (for up to 400v)
For a power diode (3 amp) try 1N5404. (for up to 400v)
For a high-speed diode, try UF4004 (for up to 400v)
If you put an ordinary diode in a high-speed application, it will get very hot very
quickly.
To replace an unknown zener diode, start with a low voltage such as 6v2 and see if the
circuit works.
The size of a diode and the thickness of the leads will give an idea of the current-
capability of the diode.
Keep the leads short as the PC board acts as a heat-sink.
You can also add fins to the leads to keep the diode cool.
LIGHT EMITTING DIODES (LEDs)
Light Emitting Diodes (LEDs) are diodes that produce light when current flows from anode to cathode. The
LED does not emit light when it is revered-biased. It is used as a low current indicator in many types of
consumer and industrial equipment, such as monitors, TV’s, printers, hi-fi systems, machinery and control
panels.
The light produced by a LED can be visible, such as red, green, yellow or white. It can also be invisible and
these LEDs are called Infrared LEDs. They are used in remote controls and to see if they are working, you
need to point a digital camera at the LED and view the picture on the camera screen.
An LED needs about 2v - 3.6v across its leads to make it emit light, but this voltage must be exact for the
type and colour of the LED. The simplest way to deliver the exact voltage is to have a supply that is higher
than needed and include a voltage-dropping resistor. The value of the resistor must be selected so the
current is between 2mA and 25mA.
The cathode of the LED is identified by a flat on the side of the LED. The life expectancy of a LED is about
100,000 hours. LEDs rarely fail but they are very sensitive to heat and they must be soldered and de-
soldered quickly. They are one of the most heat-sensitive components.
Light emitting diodes cannot be tested with most multimeters because the characteristic voltage across
them is higher than the voltage of the battery in the meter.
However a simple tester can be made by joining 3 cells together with a 220R resistor and 2 alligator clips:
LED TESTER is a very simple project from Talking Electronics that tests LEDs and diodes and
continuity. It is one of the most useful projects to add to your TEST EQUIPMENT. Connect the
clips to a LED and it will illuminate in only one direction.
The colour of the LED will determine the voltage across it. You can measure this voltage if you
want to match two or more LEDs for identical operation.
Red LEDs are generally 1.7v to 1.9v. - depending on the quality such as "high-bright"
Green LEDs are 1.9v to 2.3v.
Orange LEDs are about 2.3v and
White LEDs and IR LEDs are about 3.3v to 3.6v.
The illumination produced by a LED is determined by the quality of the crystal. It is the crystal
that produces the colour and you need to replace a LED with the same quality to achieve the
same illumination.
Never connect a LED across a battery (such as 6v or 9v), as it will be instantly damaged. You
must have a resistor in series with the LED to limit the current.
The LED TESTER also identifies a very unusual property of some LEDS. Some of the powerful
LEDs illuminate in a display but fail to illuminate when tested with LED Tester. When they are
replaced, the current take by the display reduces considerably. It seems the faulty LEDs will
illuminate but take excess current.
ZENER DIODES
All diodes are Zener diodes. For instance a 1N4148 is a 120v zener diode as this is its reverse
breakdown voltage.
And a zener diode can be used as an ordinary diode in a circuit with a voltage that is below the
zener value.
For instance, 20v zener diodes can be used in a 12v power supply as the voltage never reaches
20v, and the zener characteristic is never reached.
Most diodes have a reverse breakdown voltage above 100v, while most zeners are below 70v. A
24v zener can be created by using two 12v zeners in series and a normal diode has a
characteristic voltage of 0.7v. This can be used to increase the voltage of a zener diode by 0.7v.
See the diagram above. It uses 3 ordinary diodes to increase the output voltage of a 3-terminal
regulator by 2.1v.
To tests a zener diode you need a power supply about 10v higher than the zener of the diode.
Connect the zener across the supply with a 1k to 4k7 resistor and measure the voltage across
the diode. If it measures less than 1v, reverse the zener.
If the reading is high or low in both directions, the zener is damaged.
Here is a zener diode tester. The circuit will test up to 56v zeners.
VOLTAGE REGULATORS
A Voltage Regulator takes a high input voltage and delivers a fixed output voltage.
Providing the input voltage is 4v above the output voltage, the regulator will deliver a fixed output voltage
with almost no ripple.
Voltage regulators are also called "3-TERMINAL REGULATORS" or "REGULATOR IC's" - although this name is
not generally used.
In most cases, a voltage regulator gets quite hot and for this reason it has a high failure-rate.
If a regulator is not getting hot (or warm) it has either failed or the circuit is not operating.
A regulator can only decrease the voltage. It cannot increase the current. This means the current being
supplied to a circuit must also be available from the circuit supplying the regulator.
All regulators have different pin-outs, so you need to find the input pin and output pin and make sure the
voltage-difference is at least 4v. Some regulators will work with a difference as low as 1v, so you need to
read the specifications for the type you are servicing.
Some regulators are called “negative voltage regulators” and the input voltage will be negative and the
output will be negative.
You need to test a voltage regulator with the power "ON".
Make sure you do not allow the probes to short any of the pins together as this will destroy the regulator or
the circuit being supplied.
With the power turned off or the regulator removed from the circuit, you can test it with a multimeter set to
resistance to see if it is ok. If any resistance readings are very low or zero ohms, the regulator is damaged.
TRANSFORMERS
All transformers and coils are tested the same way. This includes chokes, coils, inductors, yokes, power
transformers, EHT transformers (flyback transformers), switch mode transformers, isolation transformers, IF
transformers, baluns, and any device that has turns of wire around a former. All these devices can go faulty.
The coating on the wire is called insulation or "enamel" and this can crack or become overheated or
damaged due to vibration or movement. When two turns touch each other, a very interesting thing
happens. The winding becomes two separate windings.
We will take the case of a single winding such as a coil. This is shown in the first diagram above and the
winding is wound across a former (a former is a bobbin or plastic molding or something to hold the winding)
and back again, making two layers. The bottom and top layers touch at the point shown in the diagram and
the current that originally passed though A, B, C, D now passes though A & D.
Winding B C becomes a separate winding as shown in the second diagram.
In other words the coil becomes a TRANSFORMER with a SHORT CIRCUIT on the secondary winding as
shown in the third diagram.
When the output wires of a transformer are shorted together, it delivers a very high current because you
have created a SHORT-CIRCUIT. This short-circuit causes the transformer to get very hot.
That’s exactly what happens when any coil or transformer gets a “shorted turn.”
The shorted turns can be a single turn or many turns.
It is not possible to measure a fault like this with a multimeter as you don’t know the exact resistance of a
working coil or winding and the resistance of a faulty winding may be only 0.001 ohms less.
However when a transformer or coil is measured with an inductance meter, an oscillating voltage (or spike)
is delivered into the core as magnetic flux, then the magnetic flux collapses and passes the energy into the
winding to produce a waveform. The inductance meter reads this and produces a value of inductance in
Henry (or milliHenry or microHenry.)
This is done with the transformer removed from the circuit and this can be a very difficult thing to do, as
most transformers have a number of connections.
If the coil or transformer has a shorted turn, the energy from the magnetic flux will pass into the turns that
are shorted and produce a current. Almost no voltage will be detected from winding.
The reading from the inductance meter will be low or very low and you have to work out if it is correct.
However there is one major problem with measuring a faulty transformer or coil.
It may only become faulty when power is applied.
The voltage between the turns may be sparking or jumping a gap and creating a problem. A tester is not
going to find this fault.
Secondly, an inductance meter may produce a reading but you do not know if the reading is correct. An
improved tester is a RING TESTER.
The circuit for a ring tester can be found here:
ISOLATION TRANSFORMER
An isolation transformer is a piece of Test Equipment that provides "Mains Voltage" but the voltage is
"floating." You will still get a shock if you touch the two output leads, but it has a special use when testing
unknown equipment.
Many electrical appliances are fully insulated and only have two leads connected to the mains.
When you take these appliances apart, you do not know which end of say a heating element is connected to
the "live" (active) side of the mains and which end connects to the neutral.
I am not suggesting you carry out the following tests, but they are described to show how an isolation
transformer works.
If you touch a soldering iron on the "live" (active) end of the heating element it will create a short-circuit.
However when the appliance is connected to the mains via an isolation transformer, you can touch an
earthed soldering iron on either end of the heater as both leads from the isolation transformer are
"floating."
Note: As soon as you earth one lead of the output an isolation transformer, the other lead becomes "active."
You can make your own Isolation Transformer by connecting two identical transformers "back-to-back."
The following diagram shows how this is done:
You can use any transformers providing the primary and secondary voltages are the same. The current
capability of the secondary winding does not matter. However if you want a supply that has almost the same
voltage as your "Mains," you need two transformers with the same voltages.
This handy isolation transformer will provide you with "Mains Voltage" but with a limited current.
In other words it will have a limited capability to supply "wattage." If you are using two 15VA transformers,
you will only be able to test an appliance rated at 15 watts.
This has some advantages and some disadvantages.
If you are working on a project, and a short-circuit occurs, the damage will be limited to 15 watts.
If you are using two transformers with different VA ratings, the lower rating will be the capability of the
combination.
If the secondaries are not equal, you will get a higher or lower "Mains Voltage."
If you get two transformers from TVs or Monitors, with a rating on the compliance plate of 45 watts, or 90
watts, you can assume the transformers are capable of delivering this wattage and making an isolation
transformer will enable you to test similar items with the safety of being isolated from the mains.
Colin Mitchell designs a lot of "LED lighting lamps" that are connected directly to the mains. He always works
with an isolating transformer, just to be safe. Working on exposed "mains" devices is extremely nerve-
wracking and you have to be very careful.
The isolation transformer will prevent a BIG EXPLOSION.
DETERMINING THE SPECS OF A TRANSFORMER
Suppose you have a "mains transformer" with unknown output voltages and unknown current capability.
You must be sure it is a mains transformer designed for operation on 50Hz or 60Hz. Switch-Mode
transformers operate at frequencies 40kHz and higher and are not covered in this discussion.
To be on the safe-side, connect the unknown transformer to the output of your isolating transformer.
Since the transformer will take almost no current when not loaded, the output voltages it produces will be
fairly accurate. Measure the input AC voltage and output AC voltage.
If the transformer has loaded your isolating transformer it will be faulty.
Mains transformers are approx 15VA for 500gm, 30VA for 1kgm 50VA for 2kgm and and 100VA for 2.5kgm.
VA stands for Volts-Amps and is similar to saying watts. Watts is used for DC circuits, while VA refers to AC
circuits.
Once you have the weight of the transformer and the output voltage, you can work out the current
capability of the secondary.
For transformers up to 30vA, the output voltage on no-load is 30% higher than the final "loaded voltage."
This is due to the poor regulation of these small devices.
If the transformer is 15VA and the output voltage is 15v AC, the current will be 1 amp AC.
You can check the "quality" of the transformer, (the regulation) by fully loading the output and measuring
the final voltage. If the transformer has a number of secondaries, the VA rating must be divided between all
the windings.
240v to 110v ISOLATION TRANSFORMER
Here's how to create a 110v isolating transformer:
Find a 240v:12v transformer.
Now find a transformer that has two secondary windings, such as 240v:12v+12v.
Connect the two transformers as shown in the circuit above. If the output is zero, connect ONE of the 12v
windings of the second transformer around the other way.
All transistors are the same but we talk about digital and analogue transistors. There is no difference
between the two.
The difference is the circuit. And the only other slight difference between transistors is the fact that some
have inbuilt diodes and resistors to simplify the rest of the circuit.
All transistors work the same way. The only difference is the amount of amplification they provide, the
current and voltage they can withstand and the speed at which they work. For simple testing purposes, they
are all the same.
NPN transistors are the most common and for an NPN transistor, the following applies.
(the opposite applies for PNP)
To test a transistor, there is one thing you have to know:
When the base voltage is higher than the emitter, current flows though the collector-emitter leads.
As the voltage is increased on the base, nothing happens until the voltage reaches 0.55v. At this point a very
small current flows through the collector-emitter leads. As the voltage is increased, the current-flow
increases. At about 0.75v, the current-flow is a MAXIMUM. (can be as high as 0.9v). That's how it works. A
transistor also needs current to flow into the base to perform this amplifying function and this is the one
feature that separates an ordinary transistor from a FET.
If the voltage on the base is 0v, then instantly goes to 0.75v, the transistor initially passes NO current, then
FULL current. The transistor is said to be working in its two states: OFF then ON (sometimes called: "cut-off"
and "saturation"). These are called digital states and the transistor is said to be a DIGITAL TRANSISTOR or
a SWITCHING TRANSISTOR , working in DIGITAL MODE.
If the base is delivered 0.5v, then slowly rises to 0.75v and slowly to 0.65v, then 0.7v, then 0.56v etc, the
transistor is said to be working in ANALOGUE MODE and the transistor is an ANALOGUE TRANSISTOR.
Since a transistor is capable of amplifying a signal, it is said to be an active device. Components such as
resistors, capacitors, inductors and diodes are not able to amplify and are therefore known as passive
components.
In the following tests, use your finger to provide the TURN ON voltage for the base (this is 0.55v to 0.7v) and
as you press harder, more current flows into the base and thus more current flows through the collector-
emitter terminals. As more current flows, the needle of the multimeter moves UP-SCALE.
For a PNP transistor, set the meter to "x10k" place the leads on the transistor and when you
press hard on the two leads shown in the diagram below, the needle will
swing almost full scale.
SIMPLEST TRANSISTOR TESTER
The simplest transistor tester uses a 9v battery, 1k resistor and a LED (any colour). Keep trying
a transistor in all different combinations until you get one of the circuits below. When you
push on the two leads, the LED will get brighter.
The transistor will be NPN or PNP and the leads will be identified:
The leads of some transistors will need to be bent so the pins are in the same positions as
shown in the diagrams. This helps you see how the transistor is being turned on. This works
with NPN, PNP transistors and Darlington transistors.
HEATSINKING
Heat generated by current flowing between the collector and emitter leads of a transistor
causes its temperature to rise. This heat must be conducted away from the transistor
otherwise the rise may be high enough to damage the P-N junctions inside the device. Power
transistors produce a lot of heat, and are therefore usually mounted on a piece of aluminium
with fins, called a HEATSINK.
This draws heat away, allowing it to handle more current. Low-power signal transistors do not
normally require heat sinking. Some transistors have a metal body or fin to connect to a larger
heatsink. If the transistor is connected to a heatsink with a mica sheet (mica washer), it can be
damaged or cracked and create a short-circuit. (See Testing Mica Washers). Or a small piece of
metal may be puncturing the mica. Sometimes white compound called Heatsink Compound is
used to conduct heat through the mica. This is very important as mica is a very poor conductor
of heat and the compound is needed to provide maximum thermal conduction.
TRANSISTOR FAILURE
Transistor can fail in a number of ways. They have forward and reverse voltage ratings and
once these are exceeded, the transistor will ZENER or conduct and may fail. In some cases a
high voltage will "puncture" the transistor and it will fail instantly. In fact it will fail much faster
via a voltage-spike than a current overload.
It may fail with a "short" between any leads, with a collector-emitter short being the most
common. However failures will also create shorts between all three leads.
A shorted transistor will allow a large current to flow, and cause other components to heat up.
Transistors can also develop an open circuit between base and collector, base and emitter or
collector and emitter.
The first step in identifying a faulty transistor is to check for signs of overheating. It may appear
to be burnt, melted or exploded. When the equipment is switched off, you can touch the
transistor to see if it feels unusually hot. The amount of heat you feel should be proportional
to the size of the transistor's heat sink. If the transistor has no heat sink, yet is very hot, you
can suspect a problem.
DO NOT TOUCH A TRANSISTOR IF IT IS PART OF A CIRCUIT THAT CARRIES 240VAC. Always
switch off the equipment before touching any components.
TRANSISTOR REPLACEMENT
If you can't get an exact replacement, refer to a transistor substitution guide to identify a near
equivalent.
The replacement part should have parameters equal to or higher than the original.
Points to remember:
- Polarity of the transistor i.e. PNP or NPN.
- At least the same voltage, current and wattage rating.
- Low frequency or high frequency type.
- Check the pinout of the replacement part
- Use a desoldering pump to remove the transistor to prevent damage to the
printed circuit board.
- Fit the heat sink.
- Check the mica washer and use heat-sink compound
- Tighten the nut/bolt - not too tight or too loose.
- Horizontal output transistors with an integrated diode should be replaced with the
same type.
DIGITAL TRANSISTORS
There is no such thing as a DIGITAL TRANSISTOR or an AUDIO TRANSISTOR.
All transistors are just "TRANSISTORS" and the surrounding components as well as the type of
signal, make the transistor operate in DIGITAL MODE or ANALOGUE MODE.
But we have some transistors that have inbuilt resistors to make them suitable for connecting
to a digital circuit without the need for a base resistor.
Here is the datasheet for an NPN transistor BCR135w and PNP datasheet for BCR185w.
These transistors are called "Digital Transistors" because the "base lead" can be connected
directly to the output of a digital stage. This "lead" or "pin" is not really the base of the
transistor but a 4k7 (or 10k) resistor connected to the base allows the transistor to be
connected to the rest of a digital circuit.
You cannot actually get to the base. The resistor(s) are built into the chip and the transistor is
converted into a "Digital Transistor" because it will accept 5v on the "b" lead.
The 47k is not really needed but it makes sure the transistor is fully turned OFF if the signal on
the "b" lead is removed (in other words - if the input signal is converted to a high-impedance
signal - see tri-state output from microcontrollers for a full explanation).
This transistor is designed to be placed in a circuit where the input changes from low to high
and high to low and does not stop mid-way. This is called a DIGITAL SIGNAL and that is one
reason why the transistor is called a digital transistor. (However you could stop half-way but
the transistor may heat up and get too hot).
Any transistor placed in a digital circuit can be called a "digital transistor" but it is better to say
it is operating in DIGITAL MODE.
The digital transistor has two resistors included inside the case
R1 is about 10k and R2 is approx 47k
These transistors can be made to work in analogue
circuits
because they are ordinary transistors with a 10k base
resistor,
but you will have to know what you are doing.
The circuit above shows the digital transistor is designed to allow a voltage of 5v to be
supplied to the "base" pin and the transistor will Fully Conduct.
This type of transistor saves putting a base resistor on the PC board.
It can be tested just like a normal transistor but the resistance between base and emitter will
be about 5k to 50k in both directions. If the collector-emitter is low in both directions the
transistor is damaged.
Here's how to look at how the transistor works:
The 10k resistor on the base will allow 0.5mA to flow into the base. But the 47k will reduce
this to 0.4mA. If the transistor has a gain of 100, the collector-emitter current can be 40mA.
To determine the current capability of the transistor, connect 100R load and turn the
transistor ON. This will allow about 100mA for the collector-emitter current. Measure the
collector-emitter voltage. If it is more than 0.5v, the transistor is OVER-LOADED.
DARLINGTON TRANSISTORS
A DARLINGTON TRANSISTOR is two transistors in a single package with three leads. They are
internally connected in cascade so the gain of the pair is very high. This allows a very small
input signal to produce a large signal at the output. They have three leads (Base, Collector
and Emitter and can be PNP or NPN) and are equivalent to the leads of a standard individual
transistor, but with a very high gain. The second advantage of a Darlington Transistor is its
high input impedance. It puts very little load on the previous circuit.
Some Darlington transistors have a built-in diode and/or built-in resistor and this will
produce a low reading in both directions between the base and emitter leads.
Darlington transistors are tested the same as an ordinary transistor and a multimeter will
produce about the same deflection, even though you will be measuring across two
junctions, (and a base-emitter resistor is present).
HORIZONTAL OUTPUT TRANSISTORS, SWITCH-MODE TRANSISTORS, FLYBACK
TRANSISTORS, POWER TRANSISTORS, VERTICAL TRANSISTORS . . . .
These are all names given to a transistor when it is used in a particular circuit. ALL these
transistors are the same for testing purposes.
We are not testing for gain, maximum voltage, speed of operation or any special feature. We
are just testing to see if the transistor is completely faulty and SHORTED.
A transistor can have lots of other faults and the circuit using the transistor is the best piece
of TEST EQUIPMENT as it is detecting the fault.
Touching the Gate will increase the voltage on the Gate and the
MOSFET will turn ON and illuminate the LED. Removing your finger will
turn the LED off.
Large devices such as the TO-220 types shown above do not like static
electricity on the gate and you have to be careful not to "spike" the
gate with any static. Generally this type of device is not "super
sensitive" and you can use your finger or a large value resistor.
When replacing one of these devices, there are 2 things to match-up.
Voltage and Current.
In most cases, the "turn-ON" resistance (the resistance between Source
and Drain) will be the same (something like 22 milli ohms) and the
speed of operation will be ok.
Check the voltage needed to turn the gate ON and make sure you can
supply the required voltage.
SILICON CONTROLLED RECTIFIERs (SCR)
The Silicon Controlled Rectifier (SCR) is a semiconductor device that is a member of a family
of control devices known as Thyristors. It is a 3-leaded device and when a small current enters
the Gate, the thyristor turns on. AND STAYS ON. It only conducts current between Anode and
Cathode in one direction and it is mainly only used in DC circuits. When it is used with AC, it
will only conduct for a maximum of half the cycle.
To understand how an SCR "latches" when the gate is provided with a small current, we can
replace it with two transistors as shown in diagram B above. When the ON button is pressed,
the BC547 transistor turns on. This turns ON the BC557 and it takes over from the action of
the switch.
To turn the circuit off, the OFF button removes the voltage from the base of the BC547.
Testing an SCR
An SCR can be tested with some multimeters but a minimum current Anode-to-Cathode is needed to
keep the device turned on. Some multimeters do not provide this amount of current and the SCR
Tester circuit above is the best way to test these devices.
Shorted SCRs can usually be detected with an ohmmeter check (SCRs usually fail shorted rather than
open).
Measure the anode-to-cathode resistance in both the forward and reverse direction; a good SCR should
measure near infinity in both directions.
Small and medium-size SCRs can also be gated ON with an ohmmeter (on a digital meter use the Diode
Check Function). Forward bias the SCR with the ohmmeter by connecting the black ( - ) lead to the anode
and the red ( + ) lead to the cathode (because the + of the battery is connected to the negative lead, in
most analogue multimeters). Momentarily touch the gate lead to the anode while the probes are still
touching both leads; this will provide a small positive turn-on voltage to the gate and the cathode-to-
anode resistance reading will drop to a low value. Even after removing the gate voltage, the SCR will stay
conducting. Disconnecting the meter leads from the anode or cathode will cause the SCR to revert to its
non-conducting state.
When making the above test, the meter impedance acts as the SCR load. On larger SCRs, it may not latch
ON because the test current is not above the SCR holding current.
SPARK GAPS
Some TV's and monitors with a CRT (picture tube), have spark gaps either on the socket at the end of the
tube or on the chassis.
These can consist of two wires inside a plastic holder or a glass tube or special resistive device.
The purpose of a spark gap is to take any flash-over (from inside the tube), to earth. This prevents damage
to the rest of the circuit.
However if the tube constantly flashes over, a carbon track builds up between the wires and effectively
reduces the screen voltage. This can cause brightness and/or focus problems. Removing the spark-gap will
restore the voltage.
These are not available as a spare component and it's best to get one from a discarded chassis.
CO-AX CABLES
Co-Ax cables can produce very high losses and it seems impossible that a few metres of cable will reduce
the signal. The author has had a 3 metre cable reduce the signal to "snow" so be aware that this can
occur. Faults can also come from a splitter and/or balun as well as dirty plugs and sockets. This can result
in very loud bangs in the sound on digital reception.
TESTING EARTH LEAKAGE DETECTORS or
Residual Current Devices or
Ground Fault Circuit Interrupters or GFCI
An Earth Leakage Detector or Sensor is a circuit designed to continuously monitor the imbalance in the
current in a pair of load carrying conductors.
These two conductors are normally the Active and Neutral. Should the imbalance current reach 30mA
the sensor will "trip" and remove the voltage (and current) from the line being monitored.
Some detectors will trip at 15mA.
You cannot alter the sensitivity of the device however there are a number of faults in these devices that
can be fixed.
In some devices the contact pressure for the 10Amp or 15 Amp contacts is very weak and they arc and
produce an open circuit. The result is this: When you press the rest button, power is not restored to the
output.
Clean the contacts with a small file and bend the metal strips to the contacts so they make a very strong
contact.
The other fault is the trip mechanism.
The magnetism from the coil does not allow the pin to move and "trip" the contacts. It may be due to a
small metal filing or the pin not moving freely enough.
All good Earth Leakage Detectors have a TEST BUTTON. This connects a resistor between the active line
and earth so that 15mA or 30mA flows.
The detector should trip immediately. Make sure the trigger mechanism trips when the test button is
pressed.
None of the electronics in the detector can be replaced however you can test the mechanical operation
and the pressure on the contacts when the unit is removed from the power. Do not work on the device
when it is connected to the mains.
TESTING CELLS AND BATTERIES
There is an enormous number of batteries and cells on the market and a number of "battery testers."
Instead of buying a battery tester that may give you a false reading, here is a method of testing cells that
is guaranteed to work.
There are two types of cell: a rechargeable cell and a non rechargeable cell.
The easiest way to test a rechargeable cell is to put a group of them in an appliance and use them until
the appliance "runs down" or fails to work. If you consider the cells did not last very long, remove them
and check the voltage of each cell. The cell or cells with the lowest voltage will be faulty. You can replace
them with new cells or good cells you have in reserve.
There is no other simple way to test a rechargeable cell.
You cannot test the "current of a cell" by using an ammeter. A rechargeable cell can deliver 10 amps or
more, even when nearly discharged and you cannot determine a good cell from a faulty cell.
However you can test them under a heavy load by placing a 1R (one ohm ) 5 watt wire wound resistor
across a cell and measure the voltage of the cell after a short period of time.
You cannot test the voltage of a cell and come to any conclusion as to the age of the cell or how much
energy remains. The voltage of a cell is characteristic to the chemicals used and the actual voltage does
not tell you its condition.
Some "dry cells" deliver 1.5v up to the end of their life whereas others drop to about 1.1v very quickly.
Once you know the name of the cell that drops to 1.1v, avoid them as the operation of the equipment
"drops off" very quickly.
However if you have a number of different cells and need to know which ones to keep, here's the
solution:
1. Check the voltage and use those with a voltage above 1.1v
2. Next, select 500mA or 10A range on a multi-meter and place the probes on a cell. For a AAA or AA cell,
the current should be over 500mA and the needle will swing full scale very quickly.
Keep the testing short as you are short-circuiting the cell but it is the only way to determine the internal
impedance of the cell and this has a lot to do with its stage-of-charge.
This will give you a cell with a good terminal voltage and a good current capability.
This also applies to button cells, but the maximum current they will deliver will be less.
If you want to get the last of the energy out of a group of cells they can be used in the following circuits:
REPLACING A SPEAKER
Replacing a speaker is easy. Just get one the same size and impedance and the job is done.
But there is a lot more to understand behind this simple replacement.
The principle of operation of a speaker is called ELECTROMAGNETISM and the strength of the "Pull" depends on
the strength of the PERMANENT MAGNET and the magnetism produced by the coil.
The strength of the coil can be produced in two different ways.
The coil can consist of a few turns and a high current flows. Or it can consist of many turns with a very low
current.
When you multiply the number of turns and the current you get a result called AMP-TURNS.
It is the AMP-TURNS that produces the FLUX (called MAGNETIC FLUX) and this flux interacts with the MAGNETIC
LINES OF FORCE produced by the PERMANENT MAGNET to produce REPULSION or ATTRACTION.
Here's the amazing part: You can replace an 8-ohm speaker with 16 ohm, 32 ohm or 50 ohm and get the same
(or even higher) output.
So, don't bypass the possibility of replacing a speaker with one having a higher impedance voice coil (VC). If the
new speaker has a super-magnet, the output will be very impressive. A higher impedance will also put less stress
on the output of the circuit and it will sometimes allow a higher voltage to be delivered to the speaker and thus
allow proportionately higher current to flow.
CONTINUITY TESTER
Now is an ideal time to introduce a simple piece of test equipment that will test all sorts of devices and
circuits.
It is a CONTINUITY TESTER
This piece of test equipment is available from Talking Electronics for $2.50 plus postage.
It is very handy handy and very clever because it has 2 levels of continuity.
The "short-circuit" probe detects low resistance and beeper-buzzer produces a noise when a low
resistance is present (up to about 50 ohms).
The High Sensitivity probe is amplified by the transistor and will detect up to about 30k.
It's ideal for measuring and comparing a fault project with a project that works as you can hear the
different tones from the buzzer and detect quite small differences in resistance.
You don't realise the importance of a simple piece of test gear like this, until you get one. We use it all the
time.
Now, back to the speaker discussion:
Most speakers have an 8R voice coil and the actual resistance may be slightly lower than this.
Some speakers have a resistance of 16R, 32R or 50R and even 75 ohms.
You would think putting a 16R speaker in place of 8R would reduce the sound output, but this is not
always the case.
You can even use 50R or 75R and get the same performance.
This may sound amazing, but here is the reason.
The cone is deflected a certain amount due to the current flowing and the number of turns.
These two values are multiplied together to produce a value called AMP-TURNS.
If we have an 8R speaker with 80 turns and 100mA, the result is 0.1 x 80 = 8.
If we use a 16R speaker, the average current flow will be 50mA and the number of turns will be about
160. The multiplication of 0.05 x 160 = 8.
The author then tried a 50R speaker and the sound output was equal to 8R and the same with 75R
speaker.
This might not apply in all situations, but the 75R speaker was slightly larger and the ticking sound form
the Metal Detector kit was louder than using an 8R mini speaker.
To see if the cone of a speaker is undamaged, push it slightly and it will move towards the magnet. If it
does not move, it is bent or damaged. If the cone is scratchy when pushed, it is rubbing against the
magnet.
A cone should be able to be pushed and pulled from its rest-state. If not, it will produce a distorted sound.
TESTING A CIRCUIT
Whenever you test a circuit, the TEST EQUIPMENT puts "a load" or "a change" on it.
It does not matter if the test equipment is a multimeter, Logic Probe, CRO, Tone Injector or simply a LED
and resistor.
There are two things you need to know.
1. The IMPEDANCE of the circuit at the location you are testing, and
2. The amount of load you are adding to the circuit via the test equipment.
There is also one other hidden factor. The test equipment may be injecting "hum" due to its leads or the
effect of your body at absorbing hum from the surroundings or the test equipment may be connected to
the mains.
These will affect the reading on the test equipment and also any output of the circuit.
Sometimes the test equipment will prevent the circuit from working and sometimes it will just change the
operating conditions slightly. You have to be aware of this.
The last section of this eBook covers High and Low Impedance and understanding impedance is
something you need to know.
The point to note here is the fact that the equipment (and the reading) can be upset by hum and
resistance/capacitance effects of test equipment. This is particularly critical in high impedance and high
frequency circuits.
TESTING INTEGRATED CIRCUITS (IC's)
Integrated Circuits can be tested with a LOGIC PROBE. A Logic Probe will tell you if a line is HIGH, LOW or
PULSING.
Most logic circuits operate on 5v and a Logic Probe is connected to the 5v supply so the readings are
accurate for the voltages being tested.
A Logic Probe can also be connected to a 12v CMOS circuit.
You can make your own Logic Probe and learn how to use it from the following link:
http://www.talkingelectronics.com/projects/LogicProbeMkIIB/LogicProbeMk-IIB.html
LOGIC PROBE with PULSE
This is a very simple transistor circuit to provide HIGH-LOW-PULSE indication for digital circuits. It can be
built for less than $5.00 on a piece of matrix board or on a small strip of copper clad board if you are using
surface mount components. The probe will detect a HIGH at 3v and thus the project can be used for 3v, 5v
and CMOS circuits.
LOGIC PROBE using CD4001 and CD4011
Here is a simple Logic Probe using a single chip. The circuits have been designed for the CD4001 CMOS
quad NOR gate and CD4011 CMOS NAND gate. The output has an active buzzer that produces a beep
when the pulse LED illuminates (the buzzer is not a piezo-diaphragm but an active buzzer containing
components).
SUPER PROBE MkII has 20 different features including a Logic Probe, capacitance tester, Inductance tester,
and more.
To test an IC, you need a circuit diagram with waveforms. These diagrams will show the signals and are
very handy if a CRO (cathode ray Oscilloscope ) is used to diagnose the problem. The CRO will reproduce
the waveform and prove the circuit is functioning correctly.
A Logic Probe will just show activity and if an output is not producing a "pulse" or "activity," you should
check the power to the IC and test the input line.
It is beyond the scope of this eBook to explain how to diagnose waveforms, however it is important to
know if signals are entering and exiting an IC and a Logic Probe is designed for this.
SIGNAL INJECTOR
This circuit is rich in harmonics and is ideal for testing amplifier circuits. To find a fault in an amplifier,
connect the earth clip to the 0v rail and move through each stage, starting at the speaker. An increase in
volume should be heard at each preceding stage. This Injector will also go through the IF stages of radios
and FM sound sections in TV's.
ANALOGUE CHIPS (also see above)
Analogue chips are AUDIO chips or AMPLIFIER chips.
To test these chips you will need three pieces of test equipment:
1. A multimeter - this can be digital or analogue.
2. A Signal Injector
3. A Mini Bench Amplifier.
The Mini Bench Amplifier is available as a kit.
If you have data on the chip, you can identify the input(s) and output(s).
A Logic Probe on each of these pins will identify activity.
A Logic Probe has 3 LEDs. Red LED indicates a HIGH, Green indicates a LOW and Orange indicates a PULSE (activity).
Some Logic Probes include a piezo and you can hear what is happening, so you don't take your eyes off the probe-
tip.
It is important not to let the probe tip slip between the pins and create a short-circuit.
LOGIC PULSER
If you have a board or a single chip and want to create activity (clock pulses), you can use a Logic Pulser. This
piece of test equipment will produce a stream of pulses that can be injected into the clock-line (clock input)
of a chip.
You can then use a Logic Probe at the same time on the outputs to observe the operation of the chip.
You can also use the Mini Bench Amplifier to detect "noise" or activity on the inputs and outputs of digital
chips.
This only applies if the frequency is in the audio range such as scanning a keyboard or switches or a display.
This is how to approach servicing/testing in a general way. There are thousands of digital chips and if you
want to test a specific chip for its exact performance, you will need to set-up a "test-bed."
REMOTE CONTROLS
There are two types of remote control - Infrared and RF. Infrared is used for short-range, line-of-sight for
TV's DVD's etc.
A few faults can be fixed, but anything complex needs a new remote control.
Check the batteries and battery-contacts. See if the IR LED is illuminating by focusing it into a digital camera
and looking on the screen for illumination.
The only other things are a sticky button, a worn-out button or a crack in the PC board. Water damage is
generally too much work to repair.
RF remote controls for cars, garage doors etc need a second working unit to check the power output.
Here is a simple circuit that can be connected to an analog multimeter to detect the signal strength at a very
close range:
To hear the tone from a transmitter, the Mini Bug Detector circuit can be used:
Any further investigation requires a circuit diagram so you can work out what is actually being
sent from the transmitter.
Most of the time it is a faulty switch, battery or contacts. Make sure the setting is correct on
the "dip switches" and use a working unit to compare all your testing.
TESTING VOLTAGES ON (in) A CIRCUIT
There are basically two different types of circuit.
1. ANALOGUE CIRCUIT
An analogue circuit can also be called an AUDIO CIRCUIT and the voltages at different points
in a circuit can be measured with a multimeter but the changes (the waveforms) will be quite
small or changing at a rapid rate and cannot be detected by a multimeter.
You need a CRO to "see" the signals or a Signal Injector to inject a waveform into the circuit
and hear the result on the circuit's speaker.
2. DIGITAL CIRCUIT
A digital circuit can also be called a "Computer Circuit" or "Logic Circuit" and some of the
voltages can be measured with a multimeter (such as supply voltages) but the "signal lines"
will be be changing from HIGH to LOW to HIGH very quickly and these signals are detected
with a Logic Probe.
Here are some circuits with details of how to test the voltages.
Most circuits do not show voltages at various different points and we will explain what to
expect on each "stage."
A "STAGE"
A stage is a set of components with an input and output. A "stage" can also be called a "Building Block."
Sometimes it has a capacitor on the input and one on the output.
This means the stage is completely isolated as far as DC is concerned.
The stage has a supply (a DC supply) and it is producing its own voltages on various points on the "stage."
It can only process (amplify) "AC." (signals).
Sometimes the stage can be given a name, such as small-signal amplifier, push-pull amplifier or output.
If the stage has a link or resistor connected to a previous stage, the previous stage will have a "DC effect"
on the stage. In other words it will be biasing or controlling the voltages on the stage. The stage may be
called a "timer" or "delay" or "DC amplifier."
It is important to break every circuit into sections. This makes testing easy. If you have a capacitor at the
input and output, you know all the problems lie within the two capacitors.
In a digital circuit (no capacitors) you need to work on each IC (integrated Circuit) and test the input for
activity and all the outputs.
Once you have determined if the circuit is Analogue or Digital, or a combination of both, you have to look
at the rail voltage and work out the size or amplitude of the voltage or waveform.
This is done before making a test, so your predictions are confirmed.
You will need a multimeter (either Digital or Analogue) a Logic Probe and a Signal Injector (Tone
Generator). An analogue meter has the advantage that it will detect slight fluctuations of voltage at a
test-point and its readings are faster than a digital meter. A digital meter will produce an accurate voltage-
reading - so you should have both available.
HIGH IMPEDANCE AND LOW IMPEDANCE
Every point in a circuit has a characteristic called "IMPEDANCE." This has never been discussed before in any text book.
That's why it will be new to you.
In other words, every point will be "sensitive to outside noise."
An audio amplifier is a good example. If you put your finger on the active input, it will produce hum or buzz in the speaker.
This is because it is a HIGH IMPEDANCE line or high impedance section of the circuit.
The same applies to every part in a circuit and when you place Test Equipment on a line for testing purposes, the equipment
will "upset" the line. It may be very slight but it can also alter the voltage on the point CONSIDERABLY.
We have already mentioned (above) how a cheap multimeter can produce a false readingwhen measuring across a 1M
resistor. That's why you need high impedance test Equipment so you do not "load" the point you are testing and create an
inaccurate reading.
The word Impedance really means resistance, but when you have surrounding components such as diodes, capacitors,
transistors, coils, Integrated Circuits, supply-voltages and resistors, the combined effect is very difficult to work out as a
"resistance" and that's why we call it "Impedance."
The term "High and Low Impedance" is a relative term and does not have any absolute values but we can mention a few
points to help you decide.
In general, the base of a transistor, FET input of an IC are classified as HIGH IMPEDANCE.
The output of these devices are LOW IMPEDANCE.
Power rails are LOW IMPEDANCE.
An oscillator circuit and timing circuit are HIGH IMPEDANCE.
A LOAD is low impedance.
And it gets tricky: An input can be designed to accept a low-impedance device (called a transducer or pick-up) and when the
device is connected, the circuit becomes LOW impedance, but the input circuitry is actually high impedance.
The impedance of a diode or LED is HIGH before the device sees a voltage higher than the junction voltage and then it
becomes LOW Impedance.
Impedance is one of the most complex topics however it all comes down to testing a circuit without loading it.
That's why test equipment should have an input impedance higher than 1M.
The first circuit we will investigate is the Mini Bug Detector, shown above and below. Points on the circuit have been
labelled A, B, C etc:
Point A - The first transistor is "self-biased" and will have 0.6v on the base. The antenna is connected to a 20
turn coil and you might think the coil will "short" the signals to earth.
But the coil and 470p capacitor form a circuit that oscillates at a high frequency when the antenna wire picks
up stray signals. The coil and capacitor actually amplify the signals (see Talking Electronics website: Spy
Circuits to see how a TANK CIRCUIT works) and these signals enter the base of the first transistor.
This is classified as a HIGH Impedance section because the signals are small and delicate and any loading via
test equipment will kill them. The first transistor amplifies the signals about 70 times and they appear
at Point B.
The signal passes though a 22n to Point C and the transistor amplifies the signal about 70 times to point D. Point
C is classified as high impedance as any voltage measurement at this point will upset the biasing of the stage as a
few millivolts change in base-voltage will alter the voltage on the collector considerably. Point D is classified as low
impedance as any voltage-testing will not alter the voltage appreciably.
The output of the second stage passes through a capacitor to the join of two diodes. These two diodes are not
turned on because the voltage at Point E can never rise above 0.7v as this is the voltage produced by the base-
emitter of the third transistor.
The purpose of the two diodes is to remove background noise. Background noise is low amplitude waveforms and
even though the transistor is turned on via the 220k, low amplitude signals will not be received. The third transistor
works like this: It cannot be turned ON any more because any waveform from the 22n will be "clipped" by the
bottom diode and it will never rise above 0.6v.
So, the only signal to affect the transistor is a negative signal - to turn it OFF.
Firstly we have to understand the voltage on the 22n. When the second transistor is sitting at mid-rail voltage, the
22n gets charged via the 2k2 and lower diode. When the transistor gets tuned ON, the collector voltage falls and the
left side of the 22n drops. The right side of the 22n also drops and when it drops 0.6v, the top diode starts to
conduct and when the voltage on the 22n drops more than 0.6v the third transistor starts to turn OFF. This effect is
amplified by the transistor at least 100 times and appears at Point F. All the voltages around the two diodes are
classified as HIGH Impedance as any piece of test equipment will upset the voltage and change the output.
There are some losses in amplitude of the signal as it passes through the 22n coupling capacitors but the end result
is a very high strength signal at point G. The 4th transistor drives a 10mH choke and the mini piezo is effectively a
20n capacitor that detects the "ringing" of the inductor to produce a very loud output.
The 22n capacitor on the collector eliminates some of the background noise. The choke and piezo form an
oscillatory circuit that can produce voltages above 15v, even though the supply is 3v.
The 47n capacitor at Point J is to keep the supply rails "tight" (to create a LOW Impedance) to allow weak cells to
operate the circuit.
The "Power-ON" LED tells you to turn the device off when not being used and Point L is the power supply - a low
impedance line due to the 47u electrolytic.
Testing the Mini Bug Detector
To test the Mini Bug Detector, you will need a Signal Injector.
Place the Injector on Point G and you will hear a tone. Then go to E, C and A. The tone will increase in
volume. If it does not increase, you have pin-pointed the faulty stage.
The next circuit is a combination of digital and analogue signals. It is a Logic Probe:
The voltage on a circuit (to be tested) is detected by the probe at Point A of the circuit above and the "tip" is
classified as "reasonably high impedance" as it has a 220k resistor between the tip and 0v rail. The 1M reduces the
impedance by about 20% but the inputs of the two inverters have no effect on the "tip" impedance as they are
extremely high input-impedance devices.
The 1M trim pot is designed to put put a voltage on point B that is slightly higher than mid-rail so the green LED is
turned off.
Point A will see a voltage below mid-rail and point C will be HIGH. Point C and F are low-impedance outputs.
When the tip of the probe is connected to a LOW voltage, Point B sees a LOW and Point F goes LOW to illuminate
the green LED. At the same time it removes the "jamming voltage" produced by the diode between pin 4 of the
4049 and pin 3 of the 74C14 and the oscillator between points H and J produces a low-tone via the 100k resistor
and 22n to indicate a LOW.
When the probe tip sees a HIGH, a lot more things happen.
Point C goes LOW and turns on the red LED. At the same time the 100p is in an uncharged state and the right lead
goes LOW. This takes the left lead LOW as the left lead connects to a HIGH Impedance line and pin 9 goes LOW. This
makes point E HIGH
and since the 1u is in an uncharged state, pin 11 goes HIGH. This makes point G LOW and the diode between pins 9
and 12 keeps pin 9 LOW and takes over from the pulse from the 100p. The yellow LED is illuminated. The 1u starts
to charge via the 470k and when it is approx half-charged, pin 11 sees a HIGH and point G goes low. This creates the
length of pulse for the yellow LED.
At the same time, Point L goes LOW because the "jamming diode" from pin 2 of the 4049 goes low and allows the
inverter between point L and N to produce a tone for the piezo.
In addition, Point I goes HIGH and quickly charges a 1u electrolytic. This removes the effect of the jamming diode on
pin 5 of the 74C14 and a low frequency oscillator made up of 68k and 1u between pins 5&6 turns on and off an
oscillator between points O and R to get a beep. The mini piezo is driven n bridge mode via the two gates
between points QTand PS.
Point U is a 1u electrolytic to reduce the impedance of the power rail and Point V is a protection diode to prevent
damage if the probe is connected to the supply around the wrong way.
Testing the Logic Probe
You can test the Logic Probe with the simple Logic Probe with Pulse project described above. It will let you
know if each point in the circuit is HIGH or LOW. You will also find out the difficulty in testing the points that
are HIGH Impedance, as the Probe will upset the voltage levels and the reading may be inaccurate.
1. In most cases a SHORT CIRCUIT can be detected by feeling the additional heat generated
by the component.
2. Next, turn off the supply and measure the resistance of the component. If it is lower than
expected, the component will be faulty.
3. Next, measure the voltage across the component. If it is lower than normal, the
component will be faulty.
4. Next, measure the current taken by the component. If it is higher than normal, the
component will be faulty.
5. If the component is an inductor, such as a motor, coil or transformer, you can use an
inductance meter. Compare a good winding with a faulty winding. Sometimes the fault will
disappear because an arc develops across the fault when the component is operating.
INTERNAL AND EXTERNAL SHORTS
An internal short refers to two windings shorting together and the winding has a very high resistance
between the winding and the frame on which it is wound. An external short refers to a winding shorting
to the frame of the component - such as one of the armature windings shorting to the metal core, around
which the wire is wound.
This may not be important unless another winding shorts to the metal frame and creates "inter winding"
problems (inner winding problems is within the same winding).
This is generally a broken lead or contact or a wire that has "burnt-out" or been "eaten-away" by acid
attack or galvanic action by water and voltage (current).
1. No current will flow when an OPEN CIRCUIT exists.
2. The voltage on each end of the OPEN CIRCUIT will not be the same.
3. Measure the current across the OPEN CIRCUIT and determine if excess current is flowing.
4. Join the two ends of the OPEN CIRCUIT and see if the circuit operates normally.
HEATSINKS
This is not an electronic component but it can certainly affect the operation of a circuit.
If you cannot hold your fingers on a heatsink, it is getting too hot. This is because the actual location where the heat is being generated is
much hotter than the part you are touching.
Transistors and IC's can withstand a high temperature but if they go above this temp, they BLOW UP.
They also have a shorter life when operating at a high temperature.
The secret to a good heatsink is called an INFINITE HEATSINK.
This is the metal frame of a case.
There are lots of charts and data on choosing a heatsink but they don't take into account two factors:
Sometimes a circuit takes a very high current for a short time and this creates a high temperature gradient. This will cause the transistor to
get very hot and fail.
The solution is to have two or more transistors in parallel to separate the "heat spots."
The second problem with designing a heatsink is the unknown location of the heatsink and the air-flow. Products placed on a shelf or in a
cupboard will get very little air-flow.
Remember: some transistors are mounted on thermal insulators. This means the transistor will have a voltage on it but the heatsink will be
zero voltage.
The temperature of the transistor will be MUCH HIGHER than the heatsink under the transistor and the transfer of the heat from the
transistor to the heatsink will be very slow. This can be the cause of the transistor failing. Sometimes the transistor will fail because insulation
is high temp plastic and it gets brittle. The plastic can carbonise and leak and sometimes a voltage can flash through the insulator. Some
amazing things have happened under these transistors and you may need to pull it apart and replace all the insulation.
Finally, feel the heatsink after 15 minutes and feel right up to the transistor. If you cannot touch the transistor, increase the thickness of the
heatsink or use two transistors to dissipate the heat.
To design a heatsink, you have to have some idea of the size of a heatsink for the application.
Charts and data can send you in the wrong direction.
Start with a heatsink twice the recommended size and feel the temp after 15 minutes. Put the project in a cupboard and see how the
temperature rises.
If possible, connect the heatsink to the metal case to get added dissipation and if you include fan-cooling, remember the fan will eventually
gather dust and reduce its efficiency.
It is very difficult to explain how heat passes through a mica washer or plastic washer, but if the transistor has a copper base, the heat
transfer has a value of 400. For aluminium it is 200. If it is steel, the transfer has a value of 50. For a mica sheet it is 1 and for plastic it is 0.1
Even though the sheet is very thin, the transfer is a lot less than metal-to-metal transfer.
Most references state the temperature difference is about one degree C for each watt of heat generated by the transistor.
Don't believe anything you read.
Feel the temperature yourself and if you cannot hold your finger on the transistor, fix the problem.
In the end, use a heatsink 50% larger than recommended.
TESTING PLUG PACKS
I do not recommend servicing a plugs pack when you can get them on eBay for a few dollars.
But there are couple of interesting things you can do with them.
Most of them have to be smashed apart, but some have screws and the 12v plug pack shown below cost just $2.50
posted.
The high voltage transistor used in these circuits is a MJE13003 and I have replaced a number of these transistors in
power supplies for 40 watt electronic ballasts and the circuit worked perfectly. They were not "blown-up" but just
produced a faulty flickering operation.
The same transistor is used in low-voltage supplies and the output voltage is determined by a zener, (shown in the
photo below) and this was changed from 12v to 15v to produce a 15v plug pack for a train throttle.
As soon as the output voltage reaches 12v or 15v, (the voltage of the zener) the circuit produces extra voltage and
this is passed to a LED in an opto-coupler to turn off the oscillator slightly on the "mains" side of the transformer.
The opto-coupler provides feedback for the output-to-input and the 5,000v isolation of the opto-coupler and the
insulation of the transformer produces the isolation needed to make sure the plug pack is safe to use.
When you load the output, the voltage will remain constant and the current will rise as the load increases.
Theoretically this current will rise until of the transformer is reached and the increase in current on the primary side
of the transformer passes through a 3.3 ohm resistor. When the load current reaches 1 amp, the current through
this 3R3 resistor (I do not know the value) begins to turn off the oscillator on the mains side of the circuit and this is
how both voltage and current regulating is achieved.
The first fault with these plug packs is the electros drying out and reducing capacitance.
If the high voltage transistor has blown up, its time to throw out the plug pack . . . too many parts will be damaged.
If you have spare transistors, you need to replace all the transistors in the circuit and the signal diodes and check
the power diodes and electros.
Test it on the isolating transformer described above as it is dangerous to work on as it is a LIVE circuit and if you
change lots of parts, including the fuse, it may blow up in your face if the short-circuit still exists. The isolating
transformer will prevent an explosion.
These plug packs are very good for teaching you how switch-mode circuits work and after working on a dozen of
them you will have more experience than any text book can give you.
The 3R3 current-sensing resistor is just behind the large transistor.
The far electro is 4u7 @400v and the close electro is 470u @16v.
Here is a block diagram of a Switch Mode Power Supply:
The mains is converted to DC and this becomes about 315v for 240v AC mains.
We now have an oscillator that gets turned ON for a very short period of time during a cycle. It is operating
on this 315v DC supply.
To start to understand how it works, the oscillator operates at 50kHz. This frequency does not change.
The transistor driving the transformer gets turned ON fully for a very short period of time and is then turned
OFF.
This causes a current to flow in the primary of the transformer but because the transformer is an INDUCTOR,
it takes a relatively long time for the current to increase to a high value.
So, in effect, only a very small amount of current actually flows. If we kept the transistor ON, the current
would increase to more than 100 amps because we have 300v available and the resistance of the
transformer is only a few ohms.
So we have a real challenge. We only want the amount of energy to be equal to 12v x 1amp = 12 watts
MAXIMUM.
That's what the feedback circuit via the opto-coupler does. It turns off the transistor when the output
voltage reaches 12v. At the moment, no output current will be flowing so the actual wattage needed will be
about 10 MILLIWATTS. And that's what the control circuit will do. It will shut off the power transistor when
the output voltage reaches 12v. When we load the output, the voltage will drop slightly and the feedback
circuit will increase the ON time of the power transistor to regain the 12v output.
Theoretically you can keep loading the output until more than 1 amps flows because the circuit has no
detection. But this will start to overheat the transformer because it cannot pass more than a certain wattage
from the primary to the secondary due to the limiting factor of the ferrite core.
So, the circuit has a current sensing resistor (in this case 3R) and as the current increases, the voltage across
this resistor increases and it turns down one of the oscillator transistors.
If you still want to learn more about Switch Mode Power supplies, here's a link
http://www.giangrandi.ch/electronics/smpsfix/smpsfix.shtml
THE END
This is not the full story to learning about servicing. It is just the beginning.
We have only covered the simplest tests and shown how 90% of faults can be found by checking voltages,
waveforms and looking for obvious things such as burnt out components, cracks in PC boards.
The author has fixed over 35,000 TV's, radios, stereos, VCRs and all those things that were on the market 30
years ago.
Things have not changed. It's just that some repairs cost nearly as much as buying a new product and half
the customers opt for dumping a faulty item and buying the latest "flat screen" version. That's why you have
to get things through the workshop as fast and as cheaply as possible, to make a living.
If you want any more devices added to this list, email Colin Mitchell.
To help with understanding how a transistor circuit works, we have produced an eBook:The Transistor
Amplifier. It covers a whole range of circuits using a transistor.