Max Roller

TECHNICAL PARAMETER
VOLTAGE: AC220V/110V（50/60HZ）

MAX. CURRENT: 0.5A/2.5A

(Note: please refer to the nameplate located on the back of the

games to check actual usage of voltage.)

MAX. POWER: 300W

STANDBY POWER: 60W

COIN SIZE：φ21mm ~ φ30mm (diameter)

1.2mm ~ 2.5mm (thickness)

CAPACITY OF COIN BOX: 1500pcs of coins with coin

sizeφ25mm*1.5mm

LOCATION REQUIRED: -5 ~ 40℃, humidity is less than 90%. No

contact with any corrosive liquid, no any greasiness and dirt.

DIMENSIONS: L1700mm*W960mm*H1360mm

1360

960 1700
GAME SETTING

1 Setting board

main board

SW1 SW2
ON ON DIP

OFF 1 2 3 4 5 6 7 8
ON ON DIP

OFF 1 2 3 4 5 6 7 8
main board
Descriptions:

Choose the item witch needs setting, toggle “ON” or “OFF” on setting board to

set the items.

There are 2 sets of switches on the main board, SW1 and SW2, each set with

8 switches. Toggle “ON” or “OFF” to change the setting. (Please see

attached list of setting items):

Description:

Coin: this setting decides how many coins for playing one game. If set to “1”, it

means insert 1coins for 1 game.

Playing Time: This setting decides the playing time for one game.

Standby music: This setting can decide if plays the background music during

the game is standby.

Adjustment
1. Adjust the coin selector

adjusting chip of entrance

sample coin chute

micro-adjust resistance Backward

Remove
- SLACK COIN
REPLACE

power/signal input +
Sensitivity
STRICT
GRAY COUNTER(+/-)
RED DC+12V
WHITE
BLACK
COIN SIGNAL
GROUND coin reject bar
COIN signal SW
GRAY COUNTER(-/+)

SW1 MGN NOM

N.O. accurate normal

N.C. SW3
SW2
100ms SLOW
50ms MEDIUM

COIN signal wavelength 25ms FAST

adjusting SW

Descriptions:
Step 1: remove the plastic coin from the coin sample chute and put a proper
coin in it.
Step 2: remove the screws on the back of coin entrance. Adjust the fix chip of
back of coin entrance according to the diameter of coin you will use
so that it will prevent the large coin blocking the coin mech.
Step 3: set the COIN to “ON”
Note: when power on, set this button is for insert coin.
Step 4: set the pulse of COIN signal to “50MS”.
Step 5: following the drawing to adjust the resistance for sensitivity of coin
acceptance, turn clockwise for increasing and counterclockwise for
decreasing.
2. Adjust the volume

sound board

sound board
potentiometer

Adjust the volume: Open the coin door, find out the sound board and twist
the potentiometer with screw driver to adjust the volume. Twist clockwisely
to increase the volume; counterclockwisely to decrease the volume.

Note: Please twist the potentiometer slowly to in case burning the

speaker by a sudden increase current output.
PARTS LIST
Fiberglass body:

06 07
03 05
04
08
02

01
09 10

11

12

24
21 20
22
23 13
16
17
14
18 15
19

# NAME QTY # NAME QTY

01 3-color light board 3 13 Power supply 1
02 Front light lens 3 14 Inverter 1
03 Eye blister 1 15 4” speaker 2
04 Fiberglass body 1 16 Speaker chasing light 2
05 Light strip 110cm 2 17 White light strip 15cm 1
06 Light strip A for wheel 2 18 Light board 1
07 Window acrylic 2 19 Wheel blister 1
08 Light strip for arm 2 20 Service door 1
09 Pedal switch 1 21 Blue light strip 10cm 1
10 Acrylic for seat light 2 22 Arm blister 1
11 Speaker mesh 2 23 Chasing light strip 90cm
12 Speaker acrylic 2 24 Light strip B for wheel
Cabinet:

01 02 03
04
07

05 06
08

09
10
17 11
12
14 13

15
16
# NAME QTY # NAME QTY
01 White LED light board 2 10 Decoration A 4
02 Cabinet 1 11 Amber bus acrylic 1
03 White light strip 35cm 2 12 Decoration C 1
04 Helicopter 1 13 Decoration B 1
05 Decoration E 1 14 Decoration G 1
06 Decoration D 1 15 Panel 1
07 Poli Car 1 16 Panel A 1
08 Panel acrylic 1 17 Cabinet acrylic 1
09 Decoration F 1

Service door:

01
# NAME QTY
02 01 Service door 1
02 Red round LED light 2
03
04 03 Tail light lens 2
04 White LED light 2
 Rail assembly for digger:

03 # NAME QTY
02 01 Motor bracket 1
01 02 Micro switch 1
04
03 Digger 1
04 Micro switch holder 1
05 05 Stud M5*40 1
06
06 Joint bearing SI6T/K 2
07 Motor holder 1
08 Motor DC12V 1
07 09 Rocker arm 1
10 10 Rail 1

09

08

Rail assembly for dozer:

01 02
# NAME QTY
03 01 Micro switch 1
04 02 Motor bracket 1
03 Rail 1
04 Stud M5*40 1
05 Rocker arm 1
10 06 Motor DC12V 1
07 Motor holder 1
09 08 08 Joint bearing SI6T/K 2
09 Micro switch holder 1

07 10 Dozer 1
06 05
 Rail assembly for truck:

01 01 02 # NAME QTY
02 01 Truck 1
03 02 Micro switch holder 1
03 04 05 03 Driven arm 1
04 Motor holder A 1
04
05 Motor holder B 1
06 Motor DC12V 1
10
10 07 Rocker arm 1
09 08 Stud M5*40 1
09 08 08 09 Joint bearing SI6T/K 2
10 Micro switch 1
07
07 06
06 05

Rail assembly for road roller:

01
02
05
03 04

06
10
09 08
07

# NAME QTY # NAME QTY

01 Road roller 1 06 Motor DC12V 1
02 Installation board for rail 1 07 Rocker arm 1
03 Slide rail 1 08 Joint bearing SI6T/K 2
04 Micro switch 2 09 Stud M5*175 1
05 Motor holder 1 10 Micro switch holder 1
PCB:

04 05
03

02 06
01 07

# NAME QTY # NAME QTY

01 Base board 1 05 Relay 1
02 Main board 1 06 Motor drive board 1
03 Sound board 1 07 Holder 1
04 7-color light control board 1

Coin box assembly:

02
03 04
01
05
06

09

08
07

# NAME QTY # NAME QTY

01 Coin selector 1 06 Meter bracket 1
02 Coin door 1 07 Coin box 1
03 Coin box frame 1 08 Lock #1396 1
04 Small button red 1 09 Lock #1285 1
05 Meter 1
 Control panel:

04
05
13
06
03 07 08 09
01
02
10

11 14
23 12

17 15
21 19 18
22
20
16

# NAME QTY # NAME QTY

01 End cap for handle 2 13 Control panel metal parts 1
02 Handle 1 14 Control panel acrylic 1
03 Shift knob holder 1 15 Micro switch 5
04 Shift knob 1 16 Button white 44*44 4
05 Buffer limit sleeve 2 17 Encoder sleeve 1
06 Shaft sleeve 2 18 Nylon for steering wheel 1
07 Barre shaft 1 19 Bearing 6000Z 2
08 Tension spring 1 20 Steering wheel 1
09 Shift knob slider 1 21 Center shaft 1
10 Shift knob right board 1 22 Steering wheel cover 1
11 Steering wheel base 1 23 Buffer sleeve liner 2
12 Encoder holder 1
Chassis:

09

08

10
07
11
12
13
06
05 14
04
03 15
02
01
16
17
19 18

20

# NAME QTY # NAME QTY

01 Leg leveler M16 4 11 Bellow pole 1
02 Wheel 2.5” 4 12 Nut M20 2
03 Chassis 1 13 Joint shaft 2
Bearing w/ base MZD
04 2 14 Filter 1
P204
05 Rocker arm 1 15 Motor 550W 1:100 1
06 Joint bearing SA14TK 1 16 Self-aligning ball bearing 2
07 Chassis blister 1 17 Sleeve 2
08 Bellow A 1 18 Eccentric block 2
09 Upper bracket 1 19 Motor shaft 1
10 Bellow B 1 20 Bearing bush 2