HD40-0/-2/-3 series 故障排除

Troubleshooting Page:1/2
訊息碼 故障狀況 可能的故障原因
ERROR CODE MALFUNCTION DESCRIPTION POSSIBLE REASONS OF MALFUNCTION

送電後,顯示屏內的馬達旋轉符號暫停不動時
1.安全開關故障或接觸不良
(安全開關檢知錯誤,僅適用繃縫機)
Safety switch is defective or poor connection.
The rotation symbol of the display panel freezes
after switching on the power
2.參數no.32設定值與使用之車頭機型不符合
(error of safety switch detected, only for interlock
The setting value of parameter no. 32 is unsuitable for the machine type.
machines)

1.馬達無動作時可以更換控速器作測試
When the motor remains to be not in operation, replace a speed controller for verification.
送電顯示屏無顯示故障碼,但馬達不動作,亦無功能
輸出
2.無功能輸出，主基板上的TR7,TR9,TR11,TR12,D21,D22,D24,D28等元件故障,更換主基板確
No error code is shown in the display panel but
- 認
the motor remains to be not in operation and
When there is no function output, components TR7,TR9,TR11,TR12,D21,D22,D24,D28, etc
there is no function output after switching on the
on the main board are defective.
power
Replace the main board for verification.

送電後,顯示屏PF,馬達無法動作,電箱也無沒有任
何輸出功能
(AC電源檢知異常) 主基板上的R17,OI1,SW1等元件故障,更換主基板確認
PF PF is shown in the display panel but the motor Components R17,OI1,SW1, etc on the main board are defective. Replace the main board for
remains to be not in operation and there is no verification.
function output after switching on the power.
(AC power detected to be abnormal)

送電,顯示屏無顯示,馬達無動作,亦沒有任何輸出功
能
1.確認AC電源是否正常輸入?電源開關(如果有)是否異常?
(AC電源無輸入，或是振盪迴路故障)
Make sure if there is normal input of AC power supply. If the power switch (if have) is
The display panel does not show anything and
abnormal?
NO DISPLAY the motor remains to be not in operation and
there is no function output after switching on the
2.主基板上的SW1,F1,BD1,RV1,C6,TR2,OI2,IC2,IC10等元件故障,更換主基板確認
power.
Components SW1,F1,BD1,RV1,C6,TR2,OI2,IC2,IC10,etc on the main board are defective.
(No input from AC power, or SMPS circuit is
Replace the main board for verification.
defective.)

電源ON 時,檢知到電源電壓過高,或是車縫中機器
停止,顯示屏E4!
1.插錯使用之供應電源?
(此為電壓保護,表示AC電壓過高)
Plugging in the wrong power supply?
After switching on the power, voltage of power
E4 supply is detected to be too high or the machine
2.主基板上的T1,D6,L4等元件故障,更換主基板確認
stops operation during sewing operation, E4
Components T1,D6,L4, etc on the main board are defective. Replace the main board for
shown in the display panel.
verification.
(This is voltage protection, meaning that the AC
voltage is too high)
HD40-0/-2/-3 series 故障排除
Troubleshooting Page:2/2

訊息碼 故障狀況 可能的故障原因

ERROR CODE MALFUNCTION DESCRIPTION POSSIBLE REASONS OF MALFUNCTION

1.踩下踏板,馬達平順的運轉幾針後停下,顯示屏E7!
After toeing down the pedal, the motor runs smoothly for few stitches and stops, showing
E7 in the display panel.

原因：
確檢知板連接器是否接觸不良?更換另一個馬達確認
Reasons:
Check if the connector of encoder board is properly plugged. Replace the motor body for
verification.

要將手輪靠到底,要夠接近馬達本體且不留間隙,所以螺絲孔會部份被遮住
Push the handwheel to the end, close enough to the motor body without leaving the gap.
You will find the screw hole on the handwheel partially covered.

主基板上的IC13等元件故障?更換主基板確認
Components IC13,etc on the main board are defective. Replace the main board for
verification.

確認定位參數P3,P4是否調整錯誤?或是直接參數重置
Check if the parameter no. P3,P4 for calibrating position is properly set? Or reset the
parameters directly.

2.踩下踏板,電動機根本無法運轉,然後顯示屏E7!
After toeing down the pedal, the motor remains to be not in operation, E7 shown in the
display panel.

原因：
確認縫機結構順暢,沒有卡死
Reasons:
各種原因造成馬達無法到達定位
Check if the structures of the machine run smoothly and not jammed.
E7 Various reasons causing the motor unable to
reach the right position.
主基板上的D3,ZD4,IC9,IC4,IPM1等元件故障
Components D3,ZD4,IC9,IC4,IPM1,etc on the main board are defective.

3.馬達運轉時發出噪音並停下,然後顯示屏E7!
Noise occurs during operation of motor and then the motor stops entirely, E7 shown in the
display panel.

原因：
確檢知板連接器是否接觸不良?更換另一個馬達確認
Reasons:
Check if the connector of encoder board is properly plugged. Replace the motor body for
verification.

主基板上的IC1,IC4,IC9,IPM1,OI3,OI4,OI5,OI6,OI7,OI8等元件故障?更換主基板確認
Components IC1,IC4,IC9,IPM1,OI3,OI4,OI5,OI6,OI7,OI8,etc on the main board are
defective. Replace the main board for verification.

4.縫製較厚的織物時,針不能貫穿而停止,顯示屏E7!
When sewing thicker textile, needle can not go though and operation stops, E7 shown in
the display panel.

選擇更大出力的馬達款
Select motor model with higher output.

連繫賀欣售服中心作馬達相關參數調整
Contact with HoHsing service center for adjustment of parameters related to motor.

1.調整控速器懸臂,確認磁石與基板上霍爾IC感應位置適當
送電顯示屏顯示EP,但馬達不動作,亦無功能輸出 Adjust the lever on the speed controller, make sure that the magnet is aligned with the
EP is shown in the display panel but the motor HALL IC of the speed controller pcb.
EP
remains to be not in operation and there is no
function output after switching on the power 2.直接更換控速器作測試
Replace a speed controller directly for verification.

http://www.hohsing.com