Scribd
Upload
156 views4 pages

Unit 2 Previous Questions

Unit2 previous questions emwtl

Uploaded by

my.show7777
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
156 views4 pages

Unit 2 Previous Questions

Unit2 previous questions emwtl

Uploaded by

my.show7777
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 4

Unit 2 Previous questions

Theory questions

1.Derive the expression for the input Impedance of a transmission line length
L.

2.Derive Zin for a lossless transmission line when it is terminated by

a)ZL b)Open Circuit C)Short circuit

3.Discuss in detail about the variation of Input Impedance along open and
short circuit lines with relevant graphs.

4. What is the equivalent circuit element of transmission line of length I = λ /


2 at short end and open end?

5. Define the Reflection coefficient and derive the expression for the Input
Impedance in terms of reflection coefficient

6. Derive the relation between reflection coefficient and characteristic


Impedance of a transmission line.

7.Discuss in detail about the conditions for low loss transmission lines.

8.Describe the characteristics of UHF lines

9.Write short notes on UHF lines as circuit elements.

10. Write short notes on different lengths of transmission lines with open and
load.

11. Explain the significance and utility of λ/8, λ/4 and λ/2 lines.

12.Determine the input impedance for λ/2, λ/4 and λ / 8 lines Impedance
transformations.

13.Show that a lossless transmission line of different lengths can be made to


behave as,

(1)Inductance ‘L’ (2) Capacitance ‘C’ (3) Series impedance

14.Show that a lossless quarter wave length line behaves as impedance


Inverter and a half- wavelength line behaves as 1:1 transformer.

15. Explain the significance of V max and V min positions along the
transmission line, for a complex load Z L Hence calculate the impedances at
these positions.
16. Write short note on Smith chart.

17. Explain about Smith chart and write steps how to calculate Impedance,
reactance, and wavelength using this chart.

18.Discuss the configuration of the smith chart considering the two families
of constant circles.

19.Explain the properties of Smith Chart.

20.What is a smith chart? And also explain the various applications of smith
chart In transmission line.

21.Explain how VSWR can be determining using smith chart.

22.What is impedance matching?

23.Explain the principle of Impedance matching with quarter wave


transformer.

24.Explain Quarter wave and Half wave Transmission Line.

25.Explain the operation of quarter wave transformer and mention It’s


important applications

26. Explain the operation of quarter wave transformer and mention It's
important applications

27.Explain the significance and design of single stub impedance matching.


Discuss the factors on which stub length depends?

28. Discuss about single and double stub matching.

Problems

1.For a uniform transmission line, the open and short circuit Impedances are
given by Zoc =50 +j 25, Zsc =60-j20 Find Zo of the line.

2. A transmission line of 710 ∠14degree Ω characteristic Impedance, length 100 km is


terminated in 300 Ω. Its propagation constant is 0.0007 +j0.028 per km. Find the input
impedance of the line.

3.Evaluate the equivalent lumped element parameters of a lossless short


circuited line of different lengths such as l = λ/8, l = λ/4, l = 5λ/16, l =
3λ/8 and l = λ/2.

4.A 100 Ω loss less line connects a signal of 100KHz to load of 140 Ω. The
load power is 100 mW. Calculate,
(i)Voltage reflection coefficient. (ii)VSWR. (iii) Position of
Vmax,Vmin,Imax and Imin

5. Α 50 Ω loss less line connects a signal of 50 KHz to a load of 140 Ω. The


load power is 75 Mw. Calculate,

(i)Voltage Reflection coefficient. (ii)VSWR. III) Position of Vmax Imax V min


and I min

6.A 60 ohm lossless line is 30 m long and is terminated with a load of 75 +


50 ohms at 3 MHz. Find its reflection coefficient, VSWR, Z MAX and ZMIN if the
line velocity is 60% of the velocity of light.

7.A low loss transmission line of 100 characteristics impedance is connected


to a load of 400 Ω. Calculate the reflection coefficient and standing wave
ratio.

8.Find the input impedance of a 750 lossless transmission line of length


(0.1%). If it is terminated in open circuit(Using Smith chart).

9. For a transmission line which is terminated in normalized Impedance Zn,


VSWR = 2. Find the normalized impedance magnitude.

10. A low transmission line of 100Ω characteristics Impedance is connected


to a load of 400 Ω. Calculated the reflection coefficient and standing wave
ratio.

11.By using smith chart, Find the input Impedance of 75 Ω lossless


transmission line of length 0.1λ, When the load is short.

12. A 300Ω transmission lina is connected to a load impedance of 450-j160 Ω


at 10 MHz. Find the position and length of a short circuited stub required to
match the line using Smith Chart.

13.A load 50-j100 Ω is connected across a 50 ohms line. Design a short


circuited stub to provide matching between the two at a signal frequency of
30 MHz using Smith chart.

14.An antenna with radiation resistance of Z L = 73 Ω is to be matched to a


lossless line of Zo 50 ohms. Evaluate a simple matching mechanism to
match the antenna to the line. Give the values.

15.A lossless line of 300 Ω Impedance is terminated In load impedance of


100 + j650 Ω the frequency of operation Is 60MHz. Find the length and
location of a single stub needed for impedance match.
16.The VSWR measured of UHF transmission line, working at a frequency of
300 MHz is found to be 2. If the distance between load and voltage minimum
is 0.8 meter. Calculate the value of load Impedance.

17.Estimate the equivalent circuit element of a open load end transmission


line of length l< λ/4.

You might also like