6881085E35-An QUANTAR QUANTRO Radio Service Software Instruction Manual

QUANTAR/QUANTRO
RADIO SERVICE SOFTWARE INSTRUCTION MANUAL
2011 MOTOROLA SOLUTIONS, INC. ALL RIGHTS RESERVED PRINTED IN U.S.A.
6881085E35-AN 06/30/2011
Computer Software Copyrights

The Motorola products described in this document include a copyrighted Motorola computer program. Laws in the United States and other countries, as well as International Treaties, preserve for Motorola the exclusive rights for Motorolas copyrighted computer programs, including the exclusive right to copy, reproduce, distribute, or otherwise transfer said computer program(s). Accordingly, the copyrighted Motorola computer programs contained in this document may not be copied, decompiled, reverse engineered, or reproduced in any manner and on or within any media without the express written permission of Motorola. Furthermore, the purchase of Motorola products shall not be deemed to grant either directly or by implication, estoppel, or otherwise, any license under the copyrights, patents, or patent applications of Motorola, except for the normal non-exclusive, royalty-free license to use that arises by operation of law in the sale of a product.
Document Copyrights
Motorola Solutions, Inc. All rights reserved. No duplication or distribution of this document or any portion thereof shall take place without the express written permission of Motorola. No part of this document may be reproduced, distributed, or transmitted in any form or by any means, electronic or mechanical, for any purpose without the express written permission of Motorola. To order additional copies of this document contact your Motorola sales representative.
Disclaimer
The information in this document is carefully examined, and is believed to be entirely reliable. However, no responsibility is assumed for inaccuracies. Furthermore, Motorola reserves the right to make changes to any products herein to improve readability, function, or design. Motorola does not assume any liability arising out of the applications or use of any product or circuit described herein; neither does it cover any license under its patent rights nor the rights of others.
Trademark Information
The following are registered trademarks of Motorola Solutions, Inc.: Motorola, the Motorola logo, ASTRO, ASTRO-TAC, EMBASSY, FullVision, INTELLIREPEATER, QUANTAR, QUANTRO, and SMARTZONE. The following are Motorola trademarks: CENTRACOM Elite, CENTRACOM Series, CENTRACOM Gold Series, MOSCAD, SECURENET, and Wireless Network Gateway. HP, HP-UX, OpenView, Vectra, and Hewlett Packard are registered trademarks of Hewlett-Packard Corporation. UNIX is a registered trademark of The Open Group in the United States and other countries. Any other brand or product names are trademarks or registered trademarks of their respective holders.
WARRANTY Limited Software Warranty

For the first ninety (90) days following its initial shipment, Motorola warrants that when properly used, its software will be free from reproducible defects that cause a material variance from its published specification. However, Motorola does not warrant that program operation will be uninterrupted or error- free, that each defect will be corrected, or that any program will meet Licensees particular requirements. This warranty does not cover an item of Software (i) used in other than its normal and customary manner; (ii) subjected to misuse; or (iii) subjected to modifications by Licensee or by any party other than Motorola without the prior written consent of Motorola.
Limited Media Warranty

For the first ninety (90) days following its initial shipment, Motorola warrants that the media carrying the software will be free from defects that damage the performance of the software. Motorola will replace any damaged media free of charge during the warranty period. Warranted media is limited to that which is used to transport the software (such as floppy disks and authorization key). PROMs that may store the software in equipment are not covered under this warranty.
Limitation of Liability
Motorolas total liability and Licensees sole remedy for any warranted software shall be limited to, at Motorolas option, software replacement or the payment of Licensees actual damages, not to exceed the total licensed charge paid by Licensee to Motorola for the item of software that caused the damage. The warranties set forth above extend only to the first licensee. Subsequent transferees accept these programs as is and without warranties of any kind. This warranty is given in lieu of all other warranties, express or implied, including, without limitation, the warranties of merchantability and fitness for a particular purpose. In no event shall Motorola be liable for special, incidental, or consequential damages (including, without limitation, loss of use, time or data, inconvenience, commercial loss, and lost profits or savings) to the full extent that such may be disclaimed by law even if Motorola has been advised of the possibility of such damage against licensee by any other party.
Repair of Defects
The classification of defects in Motorola-supplied software shall be the responsibility of Motorola. Remedy of defects is at the sole discretion of Motorola. If Motorola agrees to remedy a software defect, the new software will be warranted until the end of the original limited warranty period. Replacement of any software defect shall constitute Motorola supplying the Licensee with the appropriate software media and authorization key. Field installation and configuration are not included. Field software updates/upgrades and new enhancement option software will be warranted for ninety (90) days from the date of initial shipment. All warranty service will be performed at service locations designated by Motorola. Travel and associated expenses of the Licensee or such expenses incurred by Motorola for visits to Licensees location by Motorola personnel are not covered by this warranty.
TABLE
OF CONTENTS
Table of Contents
................................... ....
Chapter 1: Introduction
Intended User Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Organization of this Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Related Manuals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Chapter 2: RSS Overview

Summary of Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 User Interface Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 PC Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 Installing the RSS Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 Removing a Previous RSS Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8 Connecting the PC to the Device RSS Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11 Working with the RSS Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12 Launching the RSS Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12 Exiting the RSS Program. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13 Reading the Device Codeplug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14 Navigating Through the RSS Screens. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17 Writing Codeplug Data to the Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-20 Obtaining Codeplug Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21 File Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21 Saving Configuration Data to an Archive File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22 Opening an Archive Codeplug File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-24
Chapter 3: Optimization
Required Test Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 Verifying the Devices Configuration Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3 Device Type Programming Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5 Programming the IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6 Programming the MAC Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7 Setting the Devices Date and Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8 Programming Wireline Configuration Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9 Programming the Access Code Table Data For Conventional Systems . . . . . . . . . . . . . . . . . . . . . . . . 3-13 Programming the Access Code Table Data for 6809 Trunking Systems . . . . . . . . . . . . . . . . . . . . . . . . 3-15 Programming the Multi-Coded Squelch Table Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
TABLE OF CONTENTS
Saving User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-17 Adding New Users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-17 Modifying an Existing User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-18 Deleting an Existing User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-19 Programming the Channel Information Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-20 Programming the TRC Commands Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-25 Programming DC Remote Command Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-27 Programming the RF Configuration Data Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-29 Programming the 6809 Trunking Interface Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-31 Programming the Scan List Configuration Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-32 Programming the IntelliRepeater. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-35 Programming the Site Frequency Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-36 Programming the Site General Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-37 Programming the Site Timer Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-39 Programming Radio Modulation Partition Screens. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-40 Programming Full/Sub Band Partition Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-41 Programming Repeater Summary Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-41 Programming the Repeater Information Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-42 Programming RF Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-44 Programming the Codeplug Data into a Conventional or 6809 Station or ASTRO-TAC Comparator . . .3-46 Programming the Codeplug Data into an IntelliRepeater Station Installed in a SmartZone 2.0.3 or 2.7E System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-48 Programming the Codeplug Data into an IntelliRepeater Station Installed in a SmartZone 3.0, 3.5, or 4.1 System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-51 Performing Station Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-54 Required Test Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-55 RX and TX Wireline Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-55 Procedure A: Rx Wireline Alignment Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-57 Procedure B: Rx Wireline Equalization Alignment Procedure . . . . . . . . . . . . . . . . . . . .3-59 Procedure C: Status Tone Level Alignment Procedure . . . . . . . . . . . . . . . . . . . . . . . . .3-63 Procedure D: Optional Hi Boost Fine Tuning Procedure . . . . . . . . . . . . . . . . . . . . . . . .3-64 Procedure E: Aligning TX Wireline Procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-66 Procedure F: Aligning ASTRO Link Management Tone Procedure . . . . . . . . . . . . . . .3-68 Aligning Radio Signal Strength Indicator (RSSI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-68 Aligning Squelch Adjust Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-71 Equalizing Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-73 For QUANTAR Stations: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-73 For Quantro Stations: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-75 Calibrating Reference Oscillator Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-75 Reference Oscillator Calibration: Internal Reference Oscillator - Manual Procedure . .3-75 Reference Oscillator Calibration: Internal Reference Oscillator - Auto-Net Procedure .3-77 Reference Oscillator Calibration: External Reference Oscillator . . . . . . . . . . . . . . . . . .3-78 Reference Oscillator Calibration: Internal Ultra High Stability Oscillator (UHSO) . . . . .3-78
II
688 1085E 35-AN
0 6/30 /201 1
TABLE OF CONTENTS
Setting ASTRO Tx Align and Test Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-82 Generating ASTRO Test Patterns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-85 TDATA Calibration (6809 Trunking Station Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-88 ASTRO Bit Error Rate Reports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-90 Post-Optimization Checkout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-93
Chapter 4: Optimizing the ASTRO-TAC Comparator

Verifying the Comparators Configuration Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2 Programming the Comparator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 Programming the Hardware Configuration Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 Programming the Conventional System Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5 Programming the Smartzone System Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6 Programming the Analog Voting Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7 Programming the Port Control Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8 Performing Comparator Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9 Equalizing Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10 Reference Oscillator Calibration Procedures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10 Internal Reference Oscillator Auto-Net Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11 External Reference Oscillator Calibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11
Chapter 5: Diagnostics and Status

Station/Comparator Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 Station Metering Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 Station/Comparator Status Report Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3 Station/Comparator-Generated Status Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5 Station Status Panel Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-26 Comparator Status Panel Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-28 Station/Comparator Software Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-30 Setting Date and Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-30 Codeplug Reports. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-31 Printing a Codeplug Report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-31 Saving the Codeplug Report to a File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-32 Remote Station Disabling/Enabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-33 ASTRO-TAC Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-34
Chapter 6: Performing Post Repair Alignment

Overview of Alignment Routines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1 Test Equipment for Post-Repair Alignment Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4 Aligning Power Output Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4 Aligning Power Output Procedure for a Quantro 350W VHF Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7 Aligning Tx Deviation Gain Adjust Procedure, 350W VHF Stations . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11 Aligning Reference Modulation Compensation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-14
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
III
TABLE OF CONTENTS
Chapter 7: Version Compatibility and Upgrades

Prior to Release R07.02.02 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1 Beginning with Release R7.02.02 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-2 RSS Program Version and Station Firmware Relationship . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-2 RSS Program Versions Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-16 Retrieving Station Software Versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-17 Retrieving Comparator Software Versions and Backplane ID. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-18 Performing Upgrades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-19 Upgrading the Stations Codeplug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-19 Upgrading an Archived Codeplug File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-21 Features and System Capabilities. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-22
Chapter 8: Password Protection

How Password Protection Works . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-1 Password Time-out. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-1 Activating Password Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-1 Special Password Protection Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-2 Creating the Stations Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-2 Changing Station Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-3 Erasing Station Password (Local Access). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-4 Erasing Station Password (Remote Access). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-5 Bypassing the Station Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-6
Chapter 9: Remote Dial-Up

Modem Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-2 Station Modem Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-2 PC Modem Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-3
Chapter 10: WildCard Operation

Station Auxiliary Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-2 Programming the WildCard Input Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-2 Station Auxiliary Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-4 Programming the Wildcard Output Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-5 State/Action Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-6 How State/Action Tables Operate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-7 Programming the Wildcard State Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-8
Chapter 11: Software Downloading

Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-2 Preparing PC for Software Download Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-3 Adding a Null Modem Device in Microsoft Windows XP Professional . . . . . . . . . . . . . . . . . . . .11-3 Adding a Null Modem in Windows XP Professional . . . . . . . . . . . . . . . . . . . . . . . . . . .11-3
IV
688 1085E 35-AN
0 6/30 /201 1
TABLE OF CONTENTS
Adding a SLIP Connection in Windows XP Professional for a Null Modem Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-8 Adding a Dial-Up Modem Device in Microsoft Windows XP Professional . . . . . . . . . . . . . . . . 11-15 Adding a Dial-Up Modem in Windows XP Professional . . . . . . . . . . . . . . . . . . . . . . . 11-15 Adding a SLIP Connection in Windows XP Professional for a Dial-Up Modem Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-17 Adding a Virtual Network Adapter Driver in Microsoft Windows Vista and Windows 7 . . . . . . 11-25 Adding a Virtual Network Adapter Driver in Windows Vista and Windows 7 . . . . . . . 11-25 RSS SLIP Connection Naming Convention . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-33 Naming Convention for Null Modem install. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-34 Naming Convention for Dial-Up Modem install. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-34 Connecting to the Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-35 Serial (Direct) Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-35 Ethernet Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-36 Remote Dial-Up Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-38 Zone Controller Link Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-38 Loading Station Software Files onto the PC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-41 Downloading Software to Station/Receiver Memory - Conventional and 6809 Controller Systems or ASTRO-TAC Comparator Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-41 Downloading Software to IntelliRepeater Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-45
Appendix A: PL/DPL Codes Appendix B: dBm to Microvolts Conversion Appendix C: Glossary Appendix D: Acronyms
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
TABLE OF CONTENTS
VI
688 1085E 35-AN
0 6/30 /201 1
LIST
OF FIGURES
List of Figures
................................... ....
Figure 2-1 Figure 2-2 Figure 2-3 Figure 2-4 Figure 2-5 Figure 2-6 Figure 2-7 Figure 2-8 Figure 3-1 Figure 3-2 Figure 3-3 Figure 3-4 Figure 3-5 Figure 3-6 Figure 3-7 Figure 3-8 Figure 3-9 Figure 3-10 Figure 3-11 Figure 3-12 Figure 3-13 Figure 3-14 Figure 3-15 Figure 3-16 Figure 3-17 Figure 3-18 Figure 3-19 Figure 3-20 Figure 3-21 Figure 3-22 Figure 3-23 Figure 3-24 Figure 3-25 Figure 3-26 Figure 3-27 Figure 3-28
68 8 10 85 E3 5 -A N
RSS Window Overview ..................................................................................... 2-2 RSS Toolbar Buttons ......................................................................................... 2-3 RSS Menus ....................................................................................................... 2-3 Null-Modem Cable Wiring Diagram................................................................. 2-11 RSS Cable Connections .................................................................................. 2-12 Connection Screen Window ............................................................................ 2-15 RSS Information and Function Screens .......................................................... 2-20 Codeplug Size Information Window ................................................................ 2-21 Accessing the IP Address Field......................................................................... 3-6 Accessing the MAC Address Field .................................................................... 3-7 Set Date and Time Screen ................................................................................ 3-8 Wireline Configuration Screen Examples Analog Only Station Type ............. 3-9 Wireline Configuration Screen Tab Examples ASTRO Capable or ASTRO CAI Capable Station Type ................................................................. 3-10 Access Code Table Screens ........................................................................... 3-13 Access Code Table Screens ........................................................................... 3-15 Multi-Coded Squelch Table Screen................................................................. 3-16 Save Report Button to Save MCS Data .......................................................... 3-17 Channel Configuration Screen ........................................................................ 3-20 Advanced Channel Information Screen........................................................... 3-21 TRC Command Table Screen ......................................................................... 3-25 DC Command Table Screen ........................................................................... 3-28 RF Configuration Screens ............................................................................... 3-29 6809 Trunking Interface Screen ...................................................................... 3-31 Scan List Configuration Screen....................................................................... 3-33 IntelliRepeater Specific Configuration Screens ............................................... 3-35 Site Frequency Screen.................................................................................... 3-36 Site General Screen ........................................................................................ 3-37 Site Timer Screen............................................................................................ 3-39 Radio Modulation Partition Screen.................................................................. 3-40 Full/Sub Band Partition and Radio Modulation Partition Screen ..................... 3-41 Repeater Summary Screen............................................................................. 3-41 Repeater Information Screen - Basic Tab ....................................................... 3-42 Repeater Information Screen - Advanced Tab................................................ 3-42 RF Configuration Screen - Conventional Stations........................................... 3-45 RF Configuration Screen - IntelliRepeater and 6809 Trunking Stations ......... 3-45 TX Wireline Alignment Setup .......................................................................... 3-67
VII
06 / 30 / 20 11
LIST OF FIGURES
Figure 3-29 Figure 3-30 Figure 4-1 Figure 4-2 Figure 4-3 Figure 4-4 Figure 4-5 Figure 4-6 Figure 5-1 Figure 5-2 Figure 5-3 Figure 5-4 Figure 5-5 Figure 5-6 Figure 5-7 Figure 5-8 Figure 6-1 Figure 6-2 Figure 6-3 Figure 6-4 Figure 6-5 Figure 6-6 Figure 7-1 Figure 7-2 Figure 7-3 Figure 7-4 Figure 7-5 Figure 7-6 Figure 7-7 Figure 7-8 Figure 7-9 Figure 7-10 Figure 7-11 Figure 7-12 Figure 7-13 Figure 7-14 Figure 7-15 Figure 7-16 Figure 7-17 Figure 7-18
RSSI Alignment Test Setup ............................................................................ 3-69 Squelch Adjust Alignment Setup..................................................................... 3-71 Comparator Configuration Screen .................................................................... 4-3 Hardware Configuration Screen........................................................................ 4-4 Conventional System Screen............................................................................ 4-5 Smartzone System Screen ............................................................................... 4-6 Analog Voting Screen ....................................................................................... 4-7 Port Control Screen........................................................................................... 4-8 Station Metering Screen Example..................................................................... 5-3 Station Status Report Screen Example............................................................. 5-4 Comparator Status Report Screen Example..................................................... 5-5 Station Status Panel Screen Example ............................................................ 5-27 Status Panel Screen Example: Primary Comparator in an Expanded Configuration................................................................................................... 5-28 Status Panel Screen Example: Standard Comparator.................................... 5-29 Station and Comparator Version Screens....................................................... 5-30 Example of a Saved Codeplug Report............................................................ 5-33 Reference Oscillator Alignment Screen ............................................................ 6-2 Power Output Alignment Setup......................................................................... 6-5 Power Output Alignment Setup for Quantro 350W Stations ............................. 6-8 Tx Deviation Gain Adjust Alignment Setup ..................................................... 6-12 Reference Modulation Compensation Alignment Setup ................................. 6-14 Waveform Examples ....................................................................................... 6-16 Release R1.00 Features and System Capabilities Conventional................. 7-22 Release R2.00 Features and System Capabilities - Conventional ................. 7-23 Release R3.00 / R3.01 Features and System Capabilities - Conventional..... 7-24 Release R4.00 Features and System Capabilities - Conventional ................. 7-25 Release R5.00 Features and System Capabilities - Conventional ................. 7-26 Release R6.00 Features and System Capabilities - Conventional ................. 7-27 Release R7.00 Features and System Capabilities - Conventional ................. 7-28 Release R07.02.02 Features and System Capabilities - Conventional .......... 7-29 Release R08.00.00-R08.03.00 Features and System Capabilities Conventional ................................................................................................... 7-30 Release R09.00.00 Features and System Capabilities - Conventional .......... 7-31 Release R09.02.01 Features and System Capabilities - Conventional .......... 7-32 Release R09.03.00 Features and System Capabilities - Conventional .......... 7-33 Release R09.05.00/R09.06.00 Features and System Capabilities Conventional ................................................................................................... 7-34 Release R09.07.00/R10.00.00 through R10.08.00, R10.11.00, R10.12.00 Features and System Capabilities - Conventional .......................................... 7-35 Release R12.01.00 through R12.03.00 Features and System Capabilities Conventional ................................................................................................... 7-36 Release R13.00.00 through R13.02.00 Features and System Capabilities Conventional ................................................................................................... 7-37 Release R14.0.00 Features and System Capabilities - Conventional ............ 7-38 Release R2.00 Features and System Capabilities - 6809 Trunking ............... 7-39
VIII
688 1085E 35-AN
0 6/30 /201 1
LIST OF FIGURES
Figure 7-19 Figure 7-20 Figure 7-21 Figure 7-22 Figure 7-23 Figure 7-24 Figure 7-25 Figure 7-26 Figure 7-27 Figure 7-28 Figure 7-29 Figure 7-30 Figure 7-31 Figure 7-32 Figure 7-33 Figure 7-34 Figure 7-35 Figure 7-36 Figure 7-37 Figure 7-38 Figure 7-39 Figure 9-1 Figure 10-1 Figure 10-2 Figure 10-3 Figure 11-1 Figure 11-2 Figure 11-3 Figure 11-4 Figure 11-5 Figure 11-6
Release R3.00 / R3.01 Features and System Capabilities - 6809 Trunking ... 7-40 Release R4.00 Features and System Capabilities - 6809 Trunking ................ 7-41 Release R5.00 Features and System Capabilities - 6809 Trunking................ 7-42 Release R6.00 Features and System Capabilities - 6809 Trunking................ 7-43 Release R7.00 Features and System Capabilities - 6809 Trunking................ 7-44 Release R07.02.02 Features and System Capabilities - 6809 Trunking......... 7-45 Release R09.00.00 Features and System Capabilities - 6809 Trunking......... 7-46 Release R09.02.01 Features and System Capabilities - 6809 Trunking......... 7-47 Release R09.03.00 Features and System Capabilities - 6809 Trunking......... 7-48 Release R09.05.00/R09.06.00/R09.07.00/R10.00.00 through R10.08.00, R10.11.00, R10.12.00 Features and System Capabilities - 6809 Trunking .... 7-49 Release R12.01.00 through R12.03.00 Features and System Capabilities 6809 Trunking ................................................................................................. 7-50 Release R13.00.00 through R14.00.00 Features and System Capabilities 6809 Trunking ................................................................................................. 7-51 Release SZ2.0 Features and System Capabilities - IntelliRepeater Trunking 7-52 Release SZ2.3 Features and System Capabilities - IntelliRepeater Trunking 7-52 Release SZ2.7/2.7E Features and System Capabilities - IntelliRepeater Trunking .......................................................................................................... 7-52 Release 12.00.00 through 12.02.00 Features and System Capabilities IntelliRepeater SZ2.0.3 Trunking..................................................................... 7-53 Release 12.00.00 through 12.02.00 Features and System Capabilities IntelliRepeater SmartZone 3.0/3.5/4.1 Trunking ............................................. 7-53 Release 13.00.00 through 13.02.00 Features and System Capabilities IntelliRepeater SmartZone 3.0/3.5/4.1 Trunking ............................................. 7-54 Release 14.00.00 Features and System Capabilities - IntelliRepeater SmartZone 3.0/3.5/4.1Trunking ....................................................................... 7-54 Release 14.02.00 Features and System Capabilities - IntelliRepeater SmartZone 3.0/3.5/4.1Trunking....................................................................... 7-54 Release 14.00.00 Features and System Capabilities - IntelliRepeater SmartZone 2.0.3 Trunking............................................................................... 7-55 Remote Dial-Up Connection.............................................................................. 9-1 WildCard Input Screen - Enhanced Shown..................................................... 10-3 WildCard Output Screen - Enhanced Shown .................................................. 10-5 WildCard State Screen.................................................................................... 10-8 Serial Connection for Software Download..................................................... 11-35 Ethernet Connection to a Single Station ....................................................... 11-36 Ethernet Connection to IntelliRepeater Ethernet Network............................. 11-36 Remote Dial-Up Connection.......................................................................... 11-37 Zone Controller Link Connection................................................................... 11-39 Adapter for Connecting between PC and Zone Controller Link .................... 11-39
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
-IX
LIST OF FIGURES
THIS PAGE INTENTIONALLY LEFT BLANK.
-X
688 1085E 35-AN
0 6/30 /201 1
LIST
OF TABLES
List of Tables
................................... ....
Table 3-1 Table 3-2 Table 3-3 Table 3-4 Table 3-5 Table 3-6 Table 3-7 Table 3-8 Table 3-9 Table 3-10 Table 3-11 Table 3-12 Table 3-13 Table 3-14 Table 3-15 Table 3-16 Table 3-17 Table 3-18 Table 3-19 Table 3-20 Table 3-21 Table 3-22 Table 3-23 Table 4-1 Table 4-2 Table 4-3 Table 4-4 Table 4-5 Table 5-1 Table 5-2 Table 5-3 Table 6-1 Table 7-1 Table 7-2 Table 7-3
Site Number Ranges ......................................................................................... 3-4 Device Types and Applicable Screens.............................................................. 3-5 Wireline Tab Parameters................................................................................. 3-10 Tone Remote Control Tab Parameters ........................................................... 3-11 ASTRO Tab Parameters ................................................................................. 3-12 Access Code Table Field Definitions............................................................... 3-14 Access Code Table Screen Parameters ......................................................... 3-15 Channel Configuration Field Definitions .......................................................... 3-21 TRC Commands.............................................................................................. 3-26 RF Configuration Data Fields .......................................................................... 3-29 6809 Trunking Interface Screen Data Fields................................................... 3-31 Scan List Configuration Data Fields ................................................................ 3-33 IntelliRepeater Screen Fields .......................................................................... 3-35 Site Frequency Screen Data Fields................................................................. 3-37 Site General Screen Data Fields..................................................................... 3-38 Site Timer Screen Data Fields ........................................................................ 3-39 Radio Modulation Partition Screen Data Fields............................................... 3-40 Full/Sub Band Partition Screen Data Fields .................................................... 3-41 Repeater Information Screen Data Fields ....................................................... 3-43 RF Configuration Data Fields .......................................................................... 3-46 RX/TX Wireline Alignment Matrix .................................................................... 3-56 RX/TX Wireline Equalization Matrix ................................................................ 3-56 RX Wireline ASTRO Link Management Tone Alignment Matrix ..................... 3-56 Hardware Configuration Screen Data Fields..................................................... 4-4 Conventional System Screen Data Fields......................................................... 4-5 Smartzone System Screen Data Fields ............................................................ 4-6 Analog Voting Screen Data Fields .................................................................... 4-7 Port Control Screen Data Fields........................................................................ 4-8 Station / Comparator-Generated Status Messages .......................................... 5-6 Status Panel Screen Buttons .......................................................................... 5-27 Comparator Status Panel Screen Buttons ...................................................... 5-29 Alignment Procedures ....................................................................................... 6-2 TRN74751 and TRN76671 Station Control Boards RSS Compatibility ............. 7-3 TTN40941 and TRN79001 Station Control Boards RSS Compatibility.............. 7-4 CLN6960, CLN6961, CLN6873, and CLN7060 Station Control Boards (with Software Download Capability; Non-IntelliRepeater 5.0 Stations) RSS Compatibility ............................................................................................. 7-7
06 / 30 / 20 11
68 8 10 85 E3 5 -A N
XI
LIST OF TABLES
Table 7-4 Table 7-5 Table 7-6 Table 9-1 Table 10-1 Table 10-2 Table 10-3 Table 11-1 Table A-1 Table A-2 Table B-1
Factory Shipped Upgrade Kit1 RSS Compatibility (for stations without Software Download Capability) ....................................................................... 7-12 CLN6960 Station Control Boards (IntelliRepeater 5.0 Stations) RSS Version Compatibility ...................................................................................... 7-14 CLN7462 Station Control Boards (Limited QUANTAR) RSS Version Compatibility.................................................................................................... 7-15 RSS PC Modem Configuration Data Fields ...................................................... 9-5 WildCard Input Screen Data Fields................................................................. 10-3 WildCard Output Screen Data Fields .............................................................. 10-5 WildCard State/Action Screen Data Fields ..................................................... 10-9 Zone Controller Link Connection Scenarios.................................................. 11-38 Tone Private-Line (PL) Codes........................................................................... A-1 Digital Private-Line (DPL) Codes ...................................................................... A-2 dBm to Microvolts Conversion .......................................................................... B-1
XII
688 1085E 35-AN
0 6/30 /201 1
CHAPTER
Introduction
...................................
The base station products Radio Service Software (RSS) program described in this guide provides service and maintenance personnel the ability to customize, align, and troubleshoot a variety of Motorola base station products and ancillary equipment. The RSS is intended for use with the following products: QUANTAR, Quantro stations, and ASTRO-TAC receivers DSS-III data station QUANTAR data base station (DBS) ASTRO-TAC comparator
The Graphical User Interface (GUI) and context sensitive help simplify setting up the stations for operation in your system. To gain the full benefit of many features and capabilities offered by the RSS program, please read this guide and keep it handy as a reference for day to day operations.
....
NOTE
The figures provided in this guide are examples only. The screens you see may be different depending on your Microsoft Windows operating system.
Intended User Profile ...................................

The information presented in this guide is intended for use by qualified communications technicians and maintenance personnel to program, troubleshoot, and align QUANTAR and Quantro stations and ancillary equipment. It is assumed that the user is: Familiar with general communications equipment operation, alignment, and maintenance Proficient in the use of alignment and servicing test equipment, such as an oscilloscope, digital voltmeter (DVM), and the Motorola R2001 (or equivalent) communications analyzer Experienced using computers running Microsoft Windows XP, Windows Vista, Windows 7 or Windows Server 2008 R2 operating systems (OSs) and familiar with Windows applications and operations.
..
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
1-1
ORGANIZATION OF THIS GUIDE
CHAPTER 1: INTRODUCTION
Performing tasks such as copying disks and executing programs, while described in this guide, would be facilitated by a general knowledge of Microsoft Windows XP, Windows Vista, Windows 7 or Windows Server 2008 R2. Refer to your PC and OS manuals for information relating to installation, operation, and maintenance of your computer and OS. First time users should read Chapter 1 and Chapter 2 before using the RSS program to perform actual tasks. Chapter 2 serves as a basic tutorial, guiding you through loading and launching the RSS program and allowing you to investigate the various GUI screens. Users experienced in using RSS can refer to the appropriate chapter to perform a specific task.
Organization of this Guide ...................................

This guide is written in a task-oriented format, providing you with the most efficient and productive means of using the RSS program in real world applications. The guide is divided into logical chapters, each one concentrating on a particular general topic. This method of organization allows you to quickly find the information you need to perform a certain task, without having to read the entire guide or flip back and forth between chapters. The content of each chapter is summarized below. Chapter 1, Introduction, provides general information regarding this guide, including a profile of the intended audience and typographic conventions used throughout this guide. Chapter 2, RSS Overview, provides step-by-step instructions for loading the RSS software, launching the program, common practices such as saving data, and navigating through the GUI. Chapter 3, Optimization, provides step-by-step instructions for using the RSS program to optimize a newly installed station and includes codeplug programming and alignment tasks required at time of installation of station equipment. Chapter 4, Optimizing the ASTRO-TAC Comparator, provides step-by-step instructions for using the RSS program to program a newly installed ASTRO-TAC comparator. Chapter 5, Diagnostics and Status, describes how to use the diagnostics capabilities of the RSS program, also describes how to read and interpret the status report log, how to use the front panel display, and how to use the digital meeting screens. Chapter 6, Performing Post Repair Alignment, provides step-by-step procedures for performing station alignment routines. Chapter 7, Version Compatibility and Upgrades, provides information regarding RSS version compatibility issues and instructions for performing RSS and station upgrades. Chapter 8, Password Protection, describes the use of the station password protection feature. Chapter 9, Remote Dial-Up, describes how to make a dial-up connection, through a modem, to the station. This allows the RSS to be used remotely. Chapter 10, WildCard Operation, describes how to use the wildcard option feature.
..
1-2
688 1085E 35-AN
0 6/30 /201 1
RELATED MANUALS
Chapter 11, Software Downloading, describes how to download station software to FLASH memory on the station control board. Appendix A, PL/DPL Codes, provides the PL/DPL codes. Appendix B, dBm to Microvolts Conversion, provides a table of dBm to microvolt conversions. Appendix C, Glossary, provides a glossary of terms. Appendix D, Acronyms, provides a listing of acronyms and abbreviations.
Related Manuals ...................................

The following manuals may be required to supplement the information contained in this guide. The Functional Manuals provide additional servicing and troubleshooting information for use by technicians when optimizing or servicing QUANTAR or Quantro station equipment. Motorola QUANTAR Functional Manual (VHF, UHF, 800 MHz, 900 MHz) 68P81095E05 Motorola QUANTAR Data Base Station Functional Manual (UHF, 800 MHz, 900 MHz) 68P81096E05 Motorola Quantro Functional Manual (VHF, UHF, 800 MHz, 900 MHz) 68P80800E95 Motorola QUANTAR Satellite Receiver Functional Manual 68P81087E25 Motorola ASTRO-TAC Receiver Functional Manual 68P81094E85 Motorola ASTRO-TAC 3000 Digital Voting Comparator Functional Manual 68P810098E20 Microsoft software user manuals for Windows XP, Windows Vista or Windows Server 2008 R2 operating systems (refer to Microsoft system documentation for manual titles) Computer owner's manual
..
1-3
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
RELATED MANUALS
CHAPTER 1: INTRODUCTION
1-4
688 1085E 35-AN
0 6/30 /201 1
CHAPTER
RSS Overview
...................................
The model RVN5002 (ver 14.00.00 and later) RSS is a GUI-based alignment, programming, and diagnostics program for various Motorola base station and comparator products. The program is designed to run on any laptop or desktop personal computer that is capable of running Microsoft Windows XP, Windows Vista, Windows 7 or Windows Server 2008 R2. This chapter provides information on frequently performed operations such as launching the RSS program and downloading a codeplug from a connected device. The following topics are included: User Interface Description on page 2-2 PC Requirements on page 2-4 Installing the RSS Software on page 2-4 Connecting the PC to the Device RSS Port on page 2-11 Launching the RSS Program on page 2-12 Exiting the RSS Program on page 2-13 Navigating Through the RSS Screens on page 2-17 Reading the Device Codeplug on page 2-14 Writing Codeplug Data to the Device on page 2-20 Obtaining Codeplug Size on page 2-21 File Maintenance on page 2-21 (including saving and opening archive files)
Summary of Features ...................................

The RSS program provides the following features and capabilities: Read and program device codeplug data Create replacement codeplug files based on default codeplug template files included with the RSS program Optimize newly installed devices Modify or upgrade existing installations
.... ..
2-1
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
USER INTERFACE DESCRIPTION
CHAPTER 2: RSS OVERVIEW
Perform device alignment procedures Interrogate and interpret device status log files Perform comprehensive diagnostics on all device modules Perform digital metering to measure key voltages and levels
User Interface Description ...................................

The RSS programs graphical user interface provides a menu, a toolbar, a function structure tree pane, and a work area pane. See Figure 2-1, Figure 2-2, and Figure 2-3 for examples and descriptions of the RSS window, toolbar, and menus.
Close application button Menu bar Tool bar Resize window button (maximize/restore) Minimize button
..
Navigation pane Status bar
Information pane
Connection Status
Figure 2-1 RSS Window Overview
2-2
688 1085E 35-AN
0 6/30 /201 1
USER INTERFACE DESCRIPTION
File Open File Save Read Configuration From Device
Context Sensitive Help
Open Connection Screen Open Codeplug Properties
Write Configuration To Device
Figure 2-2 RSS Toolbar Buttons
NOTE
The Service and Configuration menus shown in Figure 2-3 are for a QUANTAR codeplug. The menus are slightly different if a comparator codeplug is loaded.
Figure 2-3 RSS Menus
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
2-3
PC REQUIREMENTS
PC Requirements ...................................
The following list provides the hardware requirements for the computer that has the RSS installed on it: CD/DVD drive One serial communications port Microsoft Windows XP operating system with Service Pack 3, Windows Vista operating system with Service Pack 2, Windows 7 operating system with Service Pack 1 or Windows Server 2008 R2 operating system with Service Pack 1. 110 MB free hard disk space for use by the RSS program.
..
Installing the RSS Software ...................................

The RSS software is provided on a CD. To install the RSS software, perform the following procedure:
..
NOTE
Before proceeding, ensure that the system requirements are met as outlined above.
1.
Insert the RSS distribution CD into the computers CD-ROM or DVD drive. In systems set up for self-launching executables, setup.exe launches automatically: If the installation program launches automatically, proceed to step 4. If the installation program does not launch automatically, proceed to the next step. If a previous RSS version is found to be installed, then the following window appears.
Proceed to Removing a Previous RSS Version on page 2-8. When complete, return to this section.
2.
Using either Windows Explorer or My Computer, navigate to the CD-ROM or DVD drive holding the RSS distribution CD.
2-4
688 1085E 35-AN
0 6/30 /201 1
INSTALLING THE RSS SOFTWARE
3.
Double-click setup.exe to launch it. The installation wizard sets up the system for RSS installation. Wait until the initial installation wizard window appears.
4.
Read the license agreement and click I accept the terms of the license agreement selection to accept the terms of the license. Click Next. The Setup Type window appears.
5.
6.
There are two options for installing the RSS application: The Standard installation selection installs all components of the RSS application. If this is acceptable, then click Next, and the Destination Location window appears. Proceed to step 8. The Custom installation selection allows you to choose the components of the RSS application to be installed. When you click Next, the Select Features window appears.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
2-5
7.
Select the components to be installed, then click Next. The Destination Location window appears.
8.
If the directory shown for program installation is acceptable, click Install. Otherwise, click Browse to select or create the desired directory, then click Install.
2-6
688 1085E 35-AN
0 6/30 /201 1
9.
The installation wizard installs the RSS application and indicates its progress in the status window shown in the following example.
10.
The completion window shown below appears when the RSS software has been successfully installed.
11.
Click Close. The installation wizard closes. The RSS program has been installed.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
2-7
REMOVING A PREVIOUS RSS VERSION
Removing a Previous RSS Version ...................................

Perform the procedure in this section if the installation routine has found a previous RSS version installed on your computer. The following screen appears in this situation.
1. 2.
From the Start menu in Windows, select Control Panel. From the Control Panel: For Windows XP, select Add or Remove Program. For Windows Vista, Windows 7 or Windows Server 2008 R2, select Programs and Features.
3.
From the list of programs, select Radio Service Software. For Windows XP, click the Remove button. For Windows Vista, Windows 7 or Windows Server 2008 R2, click the Uninstall button.
If the following window appears, proceed to step 4.
If the following window appears, proceed to step 7.
..
2-8
688 1085E 35-AN
0 6/30 /201 1
4.
Click Uninstall to remove the previous version's program and features. The uninstall process starts, and a progress window appears.
5.
When the uninstallation process completes, the progress window automatically closes and the following window appears.
6.
Click Close to close the window. Proceed to step 9.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
2-9
7.
Click Yes to remove the previous version's program and features. The uninstall process starts and a progress window appears.
8.
When the uninstallation process completes, the progress window automatically closes, and the following window appears.
9.
Proceed to Installing the RSS Software on page 2-4 to install the latest RSS version.
2-10
688 1085E 35-AN
0 6/30 /201 1
CONNECTING THE PC TO THE DEVICE RSS PORT
Connecting the PC to the Device RSS Port ...................................

A nine-pin male to nine-pin female EIA-232 null-modem cable (Motorola part number: 30-80369E31) is required to connect the computer to the device. Figure 2-4 provides a nullmodem cable wiring diagram.
To COM port on RSS computer (9-pin, Dtype, EIA-232 Female) 1 TXD 2 RXD 3 4 GND 5 6 RTS 7 CTS 8 9 To RSS Port on SCM front panel (9-pin, DType, EIA-232 Male) 1 2 3 4 5 6 7 8 9 RTS CTS GND TXD RXD
..
Figure 2-4 Null-Modem Cable Wiring Diagram Connect the null-modem cable from the serial port of the computer running the RSS to the RSS port on the device control module as shown in Figure 2-5. 2-11
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
WORKING WITH THE RSS PROGRAM
RSS Computer Serial COM Port 9-pin EIA-232 Female D-type connector
Station Control Module 9-pin EIA-232 Male D-type connector RSS Port
Figure 2-5 RSS Cable Connections
NOTE
The RSS cable can also be connected to the back of the chassis on connector #20.
Working with the RSS Program ................................... ..
Launching the RSS Program

1.
Launch the RSS program by either: Double-clicking the shortcut icon placed on your desktop or Selecting Radio Service Software from the Start/All Programs/Motorola/Radio Service Software menu. The splash screen appears as shown in the example below.
2-12
688 1085E 35-AN
0 6/30 /201 1
WORKING WITH THE RSS PROGRAM
2.
When the green progress bar completely fills its area, click Continue. The RSS window appears.
The RSS program is now ready to connect to the device to read its codeplug.
Exiting the RSS Program

To exit the RSS program, click X in the upper right corner of the RSS program window or from the File menu, select Exit. When the Exit message appears, click Yes to close the RSS program.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
2-13
READING THE DEVICE CODEPLUG
Reading the Device Codeplug ...................................

To read the device codeplug, perform the following steps:
1.
Launch the RSS program and connect to the device (base station) as outlined in Launching the RSS Program on page 2-12. Click either: Tools then Connection Configuration, or Open Connection Screen icon
..
2.
2-14
688 1085E 35-AN
0 6/30 /201 1
The Connection Screen window appears as shown in Figure 2-6.
Figure 2-6 Connection Screen Window

3. 4.
Select the appropriate connection type (serial or modem). Verify that the COM port selection is correct. The RSS program is provided with available COM port information. The baud rate defaults to 9600.
WARNING
If the base station is not connected to a transmitting antenna or to an appropriate piece of test equipment capable of handling the output, you must connect a dummy load to the transmitter output. Do not key the transmitter or use the station to transmit RF unless its transmitter output port is connected either to a transmitting antenna or to a 50 high-power dummy load.
5.
Ensure that the device is turned on and click Connect/Dial. The RSS attempts to connect to the device. If successful, the following message appears.
6.
Click OK. The RSS Information window closes.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
2-15
7.
Download the current codeplug information from the connected device by either: Fom the File menu, select Read from Device. Clicking Read Configuration From Device toolbar icon.
If the device requires a password, the Station Password Prompt window appears.
If required, enter the devices password and click OK. The RSS retrieves the codeplug data from the device and stores it on the PC, displaying the progress.
Start
In progress
Read codeplug verification
Successful completion
2-16
688 1085E 35-AN
0 6/30 /201 1
8.
Click Continue. The RSS window displays the following screen.
You can now review and configure the devices codeplug settings and perform diagnostic procedures.
IMPORTANT
It is advised that you save the opened codeplug as an archive before you begin changing codeplug parameters and settings. See Saving Configuration Data to an Archive File on page 2-22. This is important if your changes create problems, because it allows an easy way to revert the connected device to a functional codeplug.
Navigating Through the RSS Screens

Use the navigation pane of the RSS program window to access the various screens. Clicking the + signs in the screen hierarchy expands that branch to show the applicable information screens for a QUANTAR station.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
2-17
Collapsed screen hierarchy
Expanded screen hierarchy
Clicking a screen name imports the information into the information pane.
2-18
688 1085E 35-AN
0 6/30 /201 1
Clicking another screen name opens that screen in place of the one currently displayed. Unlike previous DOS-based RSS versions, this GUI version allows you to see the entire function list at one time. Figure 2-7 shows the structure of the information or function presented in each RSS screen.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
2-19
WRITING CODEPLUG DATA TO THE DEVICE
Figure 2-7 RSS Information and Function Screens
Writing Codeplug Data to the Device ...................................

After changes have been made to the devices codeplug data, the data must be written to the device. To upload configuration data to the device, perform the following procedure:
1.
..
Do one of the following: From the File menu, select Write to Device. Click Write Configuration to Device icon on the toolbar.
2-20
688 1085E 35-AN
0 6/30 /201 1
OBTAINING CODEPLUG SIZE
2.
Click Yes when the Confirmation window appears. The RSS program writes the configuration data entered in the current session to the connected device.
Obtaining Codeplug Size ...................................

When the codeplug has been read from the device as outlined in Reading the Device Codeplug on page 2-14, you can view the size of the codeplug by choosing Show codeplug size from the Tools menu. The Codeplug Size Information window displays the codeplug information as shown in Figure 2-8.
..
Figure 2-8 Codeplug Size Information Window
File Maintenance ...................................

File maintenance is accomplished through Windows Explorer or My Computer, as preferred. When the RSS is installed on your computer, the installation program creates a default archive directory as follows: \Motorola\Radio Service Software\archive. Specifically where this directory tree is located depends on where RSS was installed on your computer. When working with more than one device, you find it helpful to: Create an obvious directory structure to store the codeplug archives for the devices in each of the systems you work on.
..
2-21
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
FILE MAINTENANCE
Archive each devices codeplug immediately after reading it from the device in a folder that identifies the system you are currently working on, as created from suggestion above. Add comments to the archive file to further help identify the device to which it belongs.
The following sections provide RSS specific file access tasks: Saving Configuration Data to an Archive File on page 2-22. Opening an Archive Codeplug File on page 2-24.
The balance of file maintenance and disk operations, such as directory creation, are accomplished using the Windows operating system tools.
Saving Configuration Data to an Archive File

1.
To save the current sessions configuration data to an archive file, perform either of the two: From the File menu, select Save. A browser window appears. Click Save on the toolbar.
Save Menu Item
Save File Icon
2.
The Save window appears. Browse to the directory where you want to save this archive or create the directory.
NOTE
Carefully consider how you name the directories and files. Name them appropriately to simplify locating archive files later.
2-22
688 1085E 35-AN
0 6/30 /201 1
FILE MAINTENANCE
3. 4.
In the Save window, name the file appropriately in the File name field. Click Save. A message window appears.
5.
Click Yes. The Comments window appears.
NOTE
It is recommended to enter comments to aid in the identification of the codeplug.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
2-23
FILE MAINTENANCE
6.
Enter appropriate information in the Last User, Date, and File Description and Comments fields.
NOTE
Comments should be explicit enough to help you locate the archive file if needed. The information entered here is available when opening a file using Preview in the Open window to help in file identification.
7.
When done click OK. The following window appears when the codeplug is saved as an archive. Click Continue.
Opening an Archive Codeplug File

To open an archive codeplug file, perform the following steps:
1.
To open an existing archive file, perform either of the two as given below: From the File menu, select Open. A browser window appears or
2-24
688 1085E 35-AN
0 6/30 /201 1
FILE MAINTENANCE
Click Open on the toolbar.
Open Menu Item
Open File Icon
2.
The Open window appears. Browse to the directory where you saved the archive file.
3.
Select the archive file you want to open. If required, select the file name and then click Preview. This displays information about the archive file entered at the time the archive was created. See the example below.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
2-25
FILE MAINTENANCE
4.
Click Open to open the file. The codeplug archive is opened in the RSS window. If a codeplug is already loaded in the RSS, the following warning message appears.
5.
Click Yes to overwrite the currently loaded codeplug. The following message window appears when the archive file is successfully loaded in the RSS.
2-26
688 1085E 35-AN
0 6/30 /201 1
CHAPTER
Optimization
...................................
Base stations must be optimized after the initial installation and after the maintenance actions such as retuning or replacing modules. Optimization includes tasks such as verifying the station hardware configuration, performing alignment, and programming the stations codeplug. The general process for optimizing a base station is as follows:
1.
Connect the RSS computer to the station. See Connecting the PC to the Device RSS Port on page 2-11. Launch the RSS program as outlined in Launching the RSS Program on page 2-12. Read the stations codeplug. See Reading the Device Codeplug on page 2-14. Verify that the stations configuration data, as sent from Motorola, is as specified in the purchase order. See Verifying the Devices Configuration Data on page 3-3. Customize the codeplug for the stations specific installation if required. See the following as required for the specific system: Programming the IP Address on page 3-6 Programming the MAC Address on page 3-7 Setting the Devices Date and Time on page 3-8 Creating the Stations Password on page 8-2 Programming Wireline Configuration Data on page 3-9 Programming the Access Code Table Data For Conventional Systems on page 3-13 Programming the Access Code Table Data for 6809 Trunking Systems on page 3-15 Programming the Multi-Coded Squelch Table Screen on page 3-16 Programming the Channel Information Screen on page 3-20 Programming the TRC Commands Data on page 3-25 Programming DC Remote Command Data on page 3-27 Programming the RF Configuration Data Screen on page 3-29 Programming the 6809 Trunking Interface Data on page 3-31 Programming the Scan List Configuration Data on page 3-32 Programming the IntelliRepeater on page 3-35
....
2. 3. 4.
5.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
3-1
REQUIRED TEST EQUIPMENT
CHAPTER 3: OPTIMIZATION
6.
Save the updated configuration data to a file on the RSS computer as an archive of the devices current configuration as outlined in Saving Configuration Data to an Archive File on page 2-22. Save the updated configuration data to the devices codeplug as outlined in Writing Codeplug Data to the Device on page 2-20. Perform the following alignments on the device: Rx Wireline (Procedure A: Rx Wireline Alignment Procedure on page 3-57) Tx Wireline (Procedure E: Aligning TX Wireline Procedure on page 3-66) RSSI Calibration (Aligning Radio Signal Strength Indicator (RSSI) on page 3-68) Squelch Adjust (Aligning Squelch Adjust Procedure on page 3-71) Battery Equalization (if battery equipped: Equalizing Batteries on page 3-73) Reference Oscillator of UHSO (Calibrating Reference Oscillator Procedure on page 3-75) ASTRO Alignment and Test (if required: Setting ASTRO Tx Align and Test Procedure on page 3-82) ASTRO Pattern Generator (Generating ASTRO Test Patterns on page 3-85) TDATA Calibration (if required: TDATA Calibration (6809 Trunking Station Only) on page 3-88) ASTRO Bit Error Rate Reports (ASTRO only: ASTRO Bit Error Rate Reports on page 3-90)
7.
8.
9.
Perform tests to verify that optimization was successful and that the device operates properly (Post-Optimization Checkout on page 3-93).
Required Test Equipment ...................................

The following equipment is required to perform optimization: The RSS computer Communications Analyzer: Motorola R2001 (or equivalent) for non-ASTRO systems Communications Analyzer: Motorola R2500 (or equivalent) for ASTRO systems
..
3-2
688 1085E 35-AN
0 6/30 /201 1
VERIFYING THE DEVICES CONFIGURATION DATA
Verifying the Devices Configuration Data ...................................

Each device ships from Motorolas factory with a codeplug that has been custom programmed based on information on the sales order. A portion of the device codeplug data includes definitions of the device hardware configuration including serial number, ID, types of modules installed, and system and modulation type. It is recommended that you use the RSS to view this data to ensure it agrees with the equipment you are currently optimizing. Also verify that the equipment configuration agrees with the vend ticket shipped with the equipment. To access the connected devices current configuration data, perform the following procedure:
1.
Click the + sign on the Configuration node in the navigation pane to expand the Configuration branch.
2.
Click Hardware Configuration to display the devices retrieved configuration data as shown in the example below.
..
3-3
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
VERIFYING THE DEVICES CONFIGURATION DATA
You can now read the devices configuration data as programmed at the factory. SITE NUMBER Field: For simulcast stations or voting receivers, the station needs to know its "sub-site" number. This number is used to identify the station for diagnostic reporting as well as for certain infrastructure messages. The system installer must be careful that this number matches the sub-site number known. (For the 6809 determined by placement of the remote site to prime site cabling on the 6809 ACB board.) This field is used for Conventional and 6809 trunking systems, and will only be editable for voting systems, i.e., Wireline Configuration:Comparator not set to NONE. For ASTRO systems this field assigns to the station an address by which other infrastructure devices may identify it. In a wide area ASTRO system a dispatcher may "site-steer" transmissions to a particular base station by selecting that station on the console or data subsystem prior to transmitting. The comparator then routes traffic to that station utilizing that station's site number value. See Table 3-1 for the proper site number ranges. Table 3-1 SITE NUMBER RANGES Station Type
6809 Trunking 6809 Simulcast/Voting Conventional Conventional Simulcast/Voting Must be set to 0 Set to system specific site number, range is 1-16 Default value is 1 Set to system specific site number, range is 1-62, default value is 1 but must be set to value other than 1 when used with data traffic
Site Number
3.
Review the device data shown onscreen to verify that it matches the equipment and the system requirements. In most cases it matches the vend ticket, but there are circumstances where there may be discrepancies such as information missing on the original sales order, thus requiring the factory to leave certain fields at default values. The Hardware Configuration screen provides Validate Configuration to make sure that the hardware in the device matches the hardware specified on the Hardware Configuration screen. Differences are reported by the RSS through popup screens. Click Version Screen in the Service tree to review the devices current operating software versions. The information pane displays the current version information as shown in the example below.
4.
3-4
688 1085E 35-AN
0 6/30 /201 1
DEVICE TYPE PROGRAMMING OVERVIEW
5.
Change the data as required and when done save the configuration data to either: An archive file as outlined in Saving Configuration Data to an Archive File on page 2-22, or The devices codeplug as outlined in Writing Codeplug Data to the Device on page 2-20.
Device Type Programming Overview ...................................

After reading the device codeplug data into the RSS computer, it must be reviewed and edited as appropriate to match the system and user requirements specific to the particular device. Table 3-2 provides the relevant screens for each supported device type. Table 3-2 Device Types and Applicable Screens Device Type
Conventional
Applicable Screens
Hardware Configuration screen Wireline Configuration screen Access Code Table or Multi-Coded Squelch screen Channel Information screen TRC Command Table screen DC Command Table screen RF Configuration screen Scan List Configuration List WildCard screens Hardware Configuration screen Site Frequency screen Site General screen Site Timer screen Full/Sub Band Partition screen Radio Modulation Partition screen Repeater Information screen Repeater Summary screen RF Configuration screen WildCard screens Hardware Configuration screen Site Frequency screen Site General screen Site Timer screen Full/Sub Band Partition screen Radio Modulation Partition screen Repeater Information screen Repeater Summary screen RF Configuration screen WildCard screens Hardware Configuration screen Wireline Configuration screen Access Code Table screen Channel Information screen RF Configuration screen 6809 Trunking Interface WildCard screens
..
IntelliRepeater 2.0.3/2.7E
IntelliRepeater 3.0/3.5/4.1
6809 SmartZone Trunking
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
3-5
PROGRAMMING THE IP ADDRESS
Table 3-2 Device Types and Applicable Screens (continued) Device Type
6809 SMARTNET Trunking
Applicable Screens
Hardware Configuration screen Wireline Configuration screen Access Code Table screen Channel Information screen RF Configuration screen 6809 Trunking Interface WildCard screens
DSSIII
Hardware Configuration screen Channel Information screen WildCard screens Hardware Configuration screen Channel Information screen WildCard screens
QUANTAR Data Base Station
Programming the IP Address ...................................

Each device in the system requires a unique IP address for network operation. To set the devices IP address, perform the following procedure:
1.
From the Tools menu, select Set IP and MAC Address as shown in Figure 3-1. The Set IP and MAC Address window appears.
..
Figure 3-1 Accessing the IP Address Field
2. 3.
Enter the IP address in accordance with your systems network documentation. When done, click Set IP Address. The following message window appears.
3-6
688 1085E 35-AN
0 6/30 /201 1
PROGRAMMING THE MAC ADDRESS
4. 5.
Click OK. The window closes. You must reset the station to set its IP address to the value you entered. If you do not reset the station at this point, the IP you entered is not set in the device. To reset the device, click Reset. The device restarts and uses the IP address you entered when it completes the restart process.
Programming the MAC Address ...................................

The MAC address is generally hardcoded into the network interface and does not require changing unless another device on the network has the same MAC address (a very low probability). This can be treated as a read-only field in most cases. To set the devices MAC address if necessary, perform the following procedure:
1.
To set the devices MAC address, from the Tools menu, select Set IP and MAC Address as shown in Figure 3-2. The Set IP and MAC Address window appears.
..
Figure 3-2 Accessing the MAC Address Field
2. 3.
Enter the MAC address in accordance with your systems network documentation. When done, click Set Physical Address. The following message appears.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
3-7
SETTING THE DEVICES DATE AND TIME
4. 5.
Click OK. The window closes. You must reset the device to activate its MAC address to the value you entered. If you do not reset the device at this point, the MAC address you entered is not activated in the device. To restart the device, click Reset. The device restarts and uses the MAC address you entered when it completes the restart process.
Setting the Devices Date and Time ...................................

To set the devices date and time, perform the following procedure:
1.
From the Tools menu, select Set device data and time. See Figure 3-3.
..
Figure 3-3 Set Date and Time Screen

2.
The read-only portion of the window displays the RSS computers current date and time. Set the devices date and time in the appropriate fields. When done, click either OK or Apply.
3.
3-8
688 1085E 35-AN
0 6/30 /201 1
PROGRAMMING WIRELINE CONFIGURATION DATA
Programming Wireline Configuration Data ...................................

The Wireline Configuration screens allow you to set wireline parameters for device operation. To access the Wireline Configuration screen, click Wireline Configuration in the navigation pane. The appearance of the Wireline Configuration screen (Figure 3-4) is dependent on the hardware configuration as configured in the Hardware Configuration screen. If the Station Type is ANALOG ONLY, then the following applies to the Wireline Configuration screen: If the Remote Control Type is Tone Remote Control (TRC), then the TRC tab is provided for configuration (see Figure 3-4). TRC Command Table is provided in the navigation pane to set the TRC commands. If the Remote Control Type is DC, then the Wireline tab is the only tab provided in the Wireline Configuration screen. DC Command Table is provided in the navigation pane to set the DC commands.
..
If the Station Type is ASTRO CAPABLE or ASTRO Common Air Interface (CAI) CAPABLE, then the Wireline Configuration screen provides the Wireline and Astro tabs (see Figure 3-5).
Analog Station, Tone Remote Control, Wireline Tab
Analog Station, one Remote Control, TRC Tab
Analog Station, DC Remote Control
Figure 3-4 Wireline Configuration Screen Examples Analog Only Station Type
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
3-9
Figure 3-5 Wireline Configuration Screen Tab Examples ASTRO Capable or ASTRO CAI Capable Station Type The following tables provide information about each tabs parameters: Wireline tab: Table 3-3 on page 3-10 TRC tab: Table 3-4 on page 3-11 ASTRO tab: Table 3-5 on page 3-12
Table 3-3 Wireline Tab Parameters Data Field

Wireline Operation1
Description
Defines the type of wireline communications that exist between the station and remote console.
Range/Selections
2-wire half duplex 4-wire half duplex 4-wire full duplex 6-wire full duplex 8-wire full duplex
Default
2-wire half duplex
Recommended Setting (if any)

Set as required by the console connection
Console Priority Remote Control Type
If enabled, a console is connected to a 6809 trunked repeater. Defines the type of remote control used. This field is editable and is determined by the Station Type setting on the Hardware Configuration screen. Specifies the wireline circuit connected to Tone Remote Control. Specifies time interval at which station reports to its connected device that station is receiving an analog call. Specifies the type of comparator in a voting system.
Disabled Enabled ASTRO TRC DC None
Disabled N/A
Customer determined Determined by system configuration
TRC Input Outbound Analog Link Timer Comparator
Line 1 Line 2 20-300 sec
N/A 120 sec
Display only Customer determined
None DIGI-TAC SPECTRA-TAC
None
Determined by system configuration
3-10
688 1085E 35-AN
0 6/30 /201 1
Table 3-3 Wireline Tab Parameters (continued) Data Field

Fall Back In-Cabinet Repeat
Description
If enabled, station automatically repeats if voting device fails to return signal for transmission with the specified time limit (see below). See Fall Back In-Cabinet Repeat. Specifies whether status tone (typically 2175 Hz) is placed on wireline during station receiver inactivity. Specifies the status tone frequency (typically 2175 Hz) placed on wireline during station receiver inactivity. When enabled, allows the user to configure the Tx Wireline port to squelch the audio (routed to the transmitter) when the audio level fails below the threshold level as set by user. The signal is unsquelched when audio level rises above threshold level plus hysteresis. Threshold level and hysteresis value are set on Service/Alignment/TX Wireline Alignment tab. Determines whether secure signals are sent to console through wireline. Specifies whether station is allowed to equalize Rx wireline.
Range/Selections
Disabled Enabled
Default
Disabled

Customer determined
Fall Back Timer Status Tone
0 to 10,000 msec Disabled Enabled 2175 Hz
0 msec Disabled
Customer determined Depends on system design.
Status Tone Frequency Wireline Squelch
2175 Hz
Customer determined
Disabled Enabled
Disabled
Customer determined
Rx Securenet to Wireline Equalization
Disabled Enabled Disabled Enabled
Disabled Disabled
Customer determined Determined by system configuration
1. The wireline interface board is equipped with a 2-wire/4-wire jumper (JU1010). Ensure that the jumper and Wireline Operation setting are correctly set.
Table 3-4 Tone Remote Control Tab Parameters Data Field

HLGT Frequency Automatic Level Control (ALC)1 Tx Notch Filter
Description
Specifies the frequency used for high level guard tone (HLGT). If enabled, station automatically aligns Tx Wireline (TRC systems only). Removes LLGT from Tx audio signal. LLGT is same frequency as HLGT as specified above in HLGT Frequency. Removes HLGT from Rx audio signal. Removal is performed when status tone decoder, such as SPECTRR-TAC, DIGI-TAC, or CIU connected to Rx wireline, may provide false status tone detect due to high content of HLGT in audio signal. Specifies the time interval between loss of LLGT and station dekey. Allows for momentary dropout on wireline.
Range/ Selections
1900 to 3000 Hz Enabled Disabled Enabled Disabled Enabled Disabled
Default
2175 Hz Disabled Disabled

Customer determined Customer determined Enabled in systems with TRC. Disabled in all other systems Enabled in voting or SECURENET systems
Rx Notch Filter
Disabled
LLGT Undetect Time
60-2000 msec (5 msec intervals)
150 msec
Customer determined
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
3-11
Table 3-4 Tone Remote Control Tab Parameters (continued) Data Field
TRC detection algorithm Function Tones detected
Description
Specifies the algorithm type to be used when detecting TRC sequence. If set to Tight the TRC detection algorithm is more restrict. Specifies how many TRC tones can be detected after HLGT tone.
Range/ Selections
Normal, Tight
Default
Normal

Customer determined
1 to 2
Customer determined
1. Enabling ALC affects the setting of the intercom volume immediately after a station reset. The intercom volume is high and may be unintelligible. The station requires one TRC sequence, such as high level guard tone/function tone sequence, in order to properly establish line levels. Therefore, before using intercom, request that the console send any TRC sequence to the station. This sequence establishes the proper level for intercom.
Table 3-5 ASTRO Tab Parameters Data Field

Wireline Interface
Description
Defines type of ASTRO wireline interface as follows: V.24 Hybrid: Used for mixed mode, analog, and ASTRO systems, where the V.24 interface is used for ASTRO and control, and the Line 1/Line 2 wirelines are used for analog. Used only in trunked systems. Modem: Used for systems where the external connections to/from stations are through phone lines. Used for mixed mode, analog, and ASTRO systems. Not used in trunking systems. V.24 Only: Used for ASTRO only systems where the external connection is either local or through microwave link. Specifies whether external synchronization is required for transmit signal. Typically in installations where station and console are connected through a microwave link. RS232 Wireline Interface is used. Serves as diagnostic tool for V.24 Hybrid links to check the physical state of the links. Serves as diagnostic tool for all types of links to check the physical state of the links. Specifies the signal level range being input to ASTRO modem.
Range/ Selections
V.24 Hybrid Modem V.24 Only
Default
Trunking: V.24 Hybrid Conventional: Modem

Customer determined
External Transmit Clock
Enabled Disabled
Disabled
Customer determined
Analog Idle Link Check Digital Idle Link Check Modem Input Level (Tx WL)
Enabled Disabled Enabled Disabled 0 to -28 dBm or -9 to -37 dBm 0 to -20 dBm Enabled Disabled
Disabled Disabled 0 to -28 dBm
Customer determined Customer determined Depends on system configuration
Modem Output Level (Rx WL) RT/RT Configuration
Specifies the signal level being output from ASTRO modem. If enabled, allows back-to-back connection of ASTRO stations in RF link configurations.
-14 dBm Disabled
Depends on system configuration Customer determined
3-12
688 1085E 35-AN
0 6/30 /201 1
PROGRAMMING THE ACCESS CODE TABLE DATA FOR CONVENTIONAL SYSTEMS
Programming the Access Code Table Data For Conventional Systems ...................................
The appearance of the Access Code Table screen is dependent on the Station Type as configured in the Hardware Configuration screen. Click Access Code Table in the navigation pane to access the Access Code Table screen as shown in Figure 3-6.
Analog - Multi-Coded Squelch disabled
ASTRO CAI Capable - Multi-Coded Squelch set to Multi-NAC
ASTRO CAI Capable - Multi-Coded Squelch disabled
..
Figure 3-6 Access Code Table Screens Up to 16 Access Code Tables may be created to provide flexibility in the system design, accommodating a variety of console and talkgroup combinations. The number of Access Code Tables you create and the information programmed into each depends on the system design. You may choose to create one access table for each channel or allow multiple channels to share the same table. When you program the Channel Information screen (see Programming the Channel Information Screen on page 3-20) you assign a particular Access Code Table number (in the Active Code Table field) to each channel provided by the station.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
3-13
PROGRAMMING THE ACCESS CODE TABLE DATA FOR CONVENTIONAL SYSTEMS
NOTE
The number of channel information screens you create and the information programmed into each depends on the system design. Before programming the information in the Access Code Table(s), obtain the channel and access code information from the system designer. This information defines the number of channels supported by the station and the particular squelch type, PL/DPL codes or ASTRO codes to assign to each channel. Table 3-6 provides information about the Access Code Table parameters. Table 3-6 Access Code Table Field Definitions Data Field
Access Code Table Number Rx Squelch Type
Description
Identifies the current table as one of 16 possible tables. Defines the type of receiver squelch recognized by station receiver. Defines the access code corresponding to PL or DPL type specified above.
Range/ Selection
1-16 PL DPL CSQ Use Help screen or refer to tables in Appendix A of this guide PL DPL CSQ Use Help screen or refer to tables in Appendix A of this guide Enabled Disabled
Default
1 CSQ

N/A Depends on system design
Rx PL/DPL Code
CSQ
Must be valid code for selected type (PL or DPL). PL codes typically below 200 Hz Depends on system design
Tx Squelch Type
Defines the type of sub-audio tone transmitted by station.
CSQ
Tx PL/DPL Code
Defines the access code corresponding to PL or DPL type specified above.
CSQ
Must be valid code for selected type (PL or DPL). PL codes typically below 200 Hz Depends on system design
Digital Carrier Squelch
Specifies whether or not the RX ASTRO Access Code is used to qualify RX Audio. When enabled, all access codes are accepted and repeated audio goes out with Access Code 293. Defines receive ASTRO Network ID (in hex). Defines receive ASTRO Network ID (in hex). Identifies channel number(s) of station channels that use current access code table. Determines whether the station transmits using the last received NAC. Accessible only when Last Received NAC is enabled. The timer defines how long the last RX NAC is used for transmissions after the last received call. Each received call restarts the timer. Defines up to eight Rx and Tx network access codes for the specified Access Code Table Number. For ASTRO CAI voice only.
Disabled
Rx ASTRO Access Code1 Tx ASTRO Access Code1 Channels Using This Table Last Received NAC2 Last Received NAC Expiration Time
000-FFF 000-FFF 1-256 Enabled Disabled 1-30 minutes
293 293 1 Disabled 5 minutes
Depends on system design Depends on system design Status only (non-editable) Depends on system design Depends on system design
Multi-NAC Table2
0-FFF (hex)
Rx No. 1 = 293 Tx No. 1= NULL
Depends on system design
1. Applicable for ASTRO CAI Capable stations and Multi-Coded Squelch is disabled in the Hardware Configuration screen. 2. Applicable for ASTRO CAI Capable stations and Multi-Coded Squelch is set to Multi-NAC in the Hardware Configuration screen.
3-14
688 1085E 35-AN
0 6/30 /201 1
PROGRAMMING THE ACCESS CODE TABLE DATA FOR 6809 TRUNKING SYSTEMS
Programming the Access Code Table Data for 6809 Trunking Systems ...................................
The 6809 trunking systems require that the subscribers and the stations be programmed with the same system Connect Tone.
..
Analog Only
ASTRO capable
Figure 3-7 Access Code Table Screens Table 3-7 Access Code Table Screen Parameters Data Field
Connect Tone #1 Connect Tone #2 Rx ASTRO Access Codes1 Tx ASTRO Access Codes2 Smart Connect Tone Decoder Smart Connect Tone Disable Delay
Description
Specifies one of eight frequencies to be used as connect tone #1 by the station. Specifies one of the eight frequencies to be used as connect tone #2 by the station. Defines receive ASTRO network ID (hex). Defines transmit ASTRO network ID (hex). Specifies one of the two methods of minimizing time between subscriber request for service and conversation heard by receiving subscribers. If Smart Connect Tone Decoder is enabled, it specifies the amount of time allowed for 6809 controller and station to detect connect tone before dropping the call.
Range/ Selections
0 through 7 0 through 7 000-FFF (hex) 000-FFF (hex) Mute Tickle Unsquelched Disabled 0-1000 msec
Default
0 0 293 293 Mute Tickle 700 msec

Determined by system configuration Determined by system configuration Depends on system design Depends on system design Customer determined
Customer determined
1. Rx ASTRO Access Code fields are displayed only if the station type is set as ASTRO capable in the Hardware Configuration screen. 2. Tx ASTRO Access Code fields are displayed only if the station type is set as ASTRO capable in the Hardware Configuration screen.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
3-15
PROGRAMMING THE MULTI-CODED SQUELCH TABLE SCREEN
Programming the Multi-Coded Squelch Table Screen ...................................

The multi-coded squelch feature is typically used to allow the station to serve as a community repeater and allows you to track subscriber access for billing purposes. The Multi-Coded Squelch Table screen is only accessible when the following settings, on the Hardware Configuration screen, are true: Multi-Coded Squelch field is Multi-PL Only System Type is Conventional Station Type is Analog Only
When these conditions are not met, the Access Code Table screen is accessible.
..
NOTE
For accurate billing information to be available, configure the stations date and time as outlined in Setting the Devices Date and Time on page 3-8.
Figure 3-8 Multi-Coded Squelch Table Screen Subscriber radios are identified by their PL or DPL code and their usage time is logged and saved in station memory. This information may be retrieved, displayed, and saved as a text file for printing or incorporating into a report. This type of information is typically used for billing or other accounting purposes. On the initial access of the Multi-coded Squelch Table screen, a default User #1 appears with the default data. The Total Time Used and Number of Calls fields are empty. From this initial screen, up to 13 total users may be entered (12 PL and 1 DPL). When finished, the information is saved to the station codeplug. When the station is placed into service and users begin placing calls, their usage time is monitored and stored in station non-volatile memory. The RSS allows access to this information for display and saving to a text file.
3-16
688 1085E 35-AN
0 6/30 /201 1
NOTE
Multi-coded squelch is allowed on only one channel. To retrieve the multi-coded squelch information, such as usage time, you must read the codeplug from the station.
Saving User Information

To save multi-coded squelch user data information such as usage times and number of calls, you must first read the codeplug from the station. However, the information is not saved with the codeplug data when the codeplug is saved to an archive file. To save the multi-coded squelch (MCS) information, click Save Report as shown in Figure 3-9. A browser window appears, allowing you to browse to the desired directory and provide a name for the multi-coded squelch data file.
Figure 3-9 Save Report Button to Save MCS Data
Adding New Users

To add new users, perform the following procedure:
1. 2.
Click Multi-Coded Squelch Table in the navigation pane. Click the last number in the list (at the blank line) so that the cursor blinks in the numbers cell (it is non-editable).
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
3-17
3. 4.
Click Modify User. The Modify Entry window appears for that user. Enter the settings as appropriate.
5.
Click Accept to save the data. The new user is added to the list and also the next user number is added.
Modifying an Existing User

1. 2.
Click Multi-Coded Squelch Table in the navigation pane. Click the number of the user you need to modify so that the cursor blinks in the numbers cell (it is non-editable). Click Modify User. The Modify Entry window appears for that user.
3.
4. 5.
Modify the settings as required. Click Accept to save the user data or Cancel to exit without saving.
3-18
688 1085E 35-AN
0 6/30 /201 1
Deleting an Existing User

1. 2.
Click Multi-coded Squelch Table in the navigation pane. Click the number of the user to be deleted so that the cursor blinks in the numbers cell (it is non-editable). Click Modify User. The Modify Entry window appears for that user.
3.
4.
Select Delete from the User Access selection list.
5.
Click Accept. The User Table indicates the User Access as DELETE.
The current usage time and number of call data for the deleted users is erased when the codeplug is uploaded to the station.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
3-19
PROGRAMMING THE CHANNEL INFORMATION SCREEN
Programming the Channel Information Screen ...................................

The Channel Information screen allows you to specify frequencies, operating parameters, and time-out timer settings for each channel supported by the station. Up to 16 channels may be created with the data fields for each channel contained on two screen pages. The number of channel information screens you create and the information programmed into each depends on the system design. Before programming the information in the Channel Information screen(s), obtain the channel and access code information from the system designer. This information, typically recorded in a system design document, defines the number of channels supported by the station and the particular frequencies, timer settings, and other system parameters applicable to the station. See Figure 3-10 and Figure 3-11 for the Channel Configuration screens.
..
Figure 3-10 Channel Configuration Screen
3-20
688 1085E 35-AN
0 6/30 /201 1
Figure 3-11 Advanced Channel Information Screen Table 3-8 Channel Configuration Field Definitions Data Field
Channel Number Rx1 Frequency and Rx2 Frequency Tx Frequency
Description
Identifies the current channel as one of 16 possible channels. Receive frequency in MHz for current channel for Receiver #1 or Receiver #2. Transmit frequency in MHz for current channel. Defines frequency the transmit oscillator tunes to when not transmitting. Specifies the type of modulation for current channel.
Range/Selection
1-16 Depends on band 1
Default
N/A
N/A
Frequency assigned by FCC (depends on system design). Frequency assigned by FCC (depends on system design). Set to 0 to disable transmitter. N/A
Depends on band
N/A
Tx Idle Frequency1 Modulation Type
Depends on band
N/A
Analog/ASTRO ASTRO or Analog Analog/SECURENET CFS Analog/SECURENET XL SECURENET CFS SECURENET XL ASTRO CAI Analog/ASTRO CAI 5.00 kHz 4 kHz 2.5 kHz
Analog
Depends on system design.
Tx Rated Deviation
Specifies the maximum frequency deviation allowed for channel.
5.00 kHz
Determined by FCC per channel type. Depends on system design.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
3-21
Table 3-8 Channel Configuration Field Definitions (continued) Data Field

Receive Channel BW
Description
Specifies the frequency spacing (in kHz) between channels.
Range/Selection
Wide (25-30 kHz) NPSPAC (25 kHz) Narrow (12.5-15 kHz) Narrow (12.5 KHz)
Default
Wide

Determined by FCC per channel. Depends on system design. Assigned by FCC. Depends on system design. Customer defined. Depends on system design.
Call sign Call Sign Over Wireline Access Code Table Carrier Squelch Transition
Specifies the call sign for station. Assigned by FCC. Determines whether call sign is sent to console over wireline. Specifies which of the 256 possible access code tables applies to current channel. This provides two threshold selections: Normal and Shifted. Normal operation sets squelch performance so that the receiver unsquelches in 20 ms for signals above squelch set level and 180 ms for signals below squelch set level but above receiver sensitivity. Shifted operation sets squelch performance so that the receiver unsquelches in 20 ms for signals above 1 uV and unsquelches in 180 ms for signals below 1 uV but above the receiver sensitivity. Specifies the type of squelch required to unsquelch receiver.
Alphanumeric (15 characters max) Enabled Disabled 0-16 (0 = none)
N/A Disabled 1
Normal Shifted
Normal
Customer defined.
Analog Rx Activation
Off S = Carrier Squelch C = PL/DPL SC = Carrier and PL/DPL On = Unsquelched Off S = Carrier Squelch C = PL/DPL SC = Carrier and PL/DPL On = Unsquelched Off S = Carrier Squelch C = PL/DPL SC = Carrier and PL/DPL On = Unsquelched
Off
Customer defined. See help for details. Depends on system design.
Analog Repeater Activation
Specifies the type of squelch required to activate repeater.
Off
Analog Repeater Hold-In
Specifies the type of squelch required to maintain repeater activation.
Off
Analog Repeater Access
Specifies whether repeater is activated by carrier detect/PL - DPL detect or subscriber-generated tone (DTMF, MDC preamble, or Singletone). If set for MDC/Tone, SAM board must be programmed with corresponding tones. Specifies the output power from the station power amplifier module. This field is limited to a pre-determined output power level if the station is equipped with the Limited Output Power option.
None MDC/Tone
None
Tx Power Out
Approximately 50% to 110% (Quantro) or 25% to 110% (QUANTAR) of PA rating.
Value entered in Channel Configuration screen.
Refer to system design document for FCC licensed power rating.
3-22
688 1085E 35-AN
0 6/30 /201 1
Table 3-8 Channel Configuration Field Definitions (continued) Data Field Description Range/Selection Default Recommended Setting (if any)
IMPORTANT
When setting the output power on a QUANTAR station with high power booster, divide the desired station output power by 18.75 and enter this value in the TX Power Out field. For example, to set the station's maximum output power to 300W, enter a value of 16 (300 18.75). The output power appears with 7% of the desired value. Do not set the VHF station power amplifier modules to greater than 18 W, or 800 MHz station power amplifier modules to greater than 16W.
Battery Backup Specifies the output power from the station power amplifier module when in battery backup mode. Refer to the Important note in Tx Power Out. Approximately 50% to 110% (Quantro) or 25% to 110% (QUANTAR) of PA rating. 50% of value entered in Channel Configuration screen. Customer defined. Set to lower value to extend station operation in battery backup mode.
Time Out Timers:

Wireline Specifies the maximum amount of time transmitter may be continuously activated by console through wireline. Specifies the maximum amount of time transmitter may be continuously activated by local microphone/handset. Specifies the maximum amount of time repeater mode may be continuously activated by subscriber through receiver. Specifies the time a user may retain MRTI interface by holding PTT before system cancels transmission. 0-2550 seconds (0 = disabled) 120 sec Customer defined
Local
0-2550 seconds (0 = disabled)
0 sec
Customer defined
Repeater
0 sec
Customer defined
MRTI
0 sec
Customer defined
Alarm Tone:
Over Air Over WL Specifies whether station alarm tones (four total) are transmitted over air. Specifies whether station alarm tones (four total) are transmitted over wireline to console. Enabled Disabled Enabled Disabled Disabled Disabled Customer defined Customer defined
Audio Filters:
Pre-emphasis Specifies whether analog audio is passed through internal +6 dB per octave slope filter prior to transmission. Specifies whether analog audio is passed through internal -6 dB per octave slope filter prior to transmission. Specifies whether analog audio is passed through internal 300 Hz corner high pass filter. Filters PL or DPL lowfrequency signaling. Enabled Disabled Enabled Disabled Enabled Disabled Enabled Customer determined
De-emphasis
Enabled
Customer determined
Hi-pass Filter
Enabled
Customer determined
SECURENET:
WL CSQ Mute Timer This parameter is used when the channel is configured for SECURENET and Rx Activation is set to CSQ to specify the time that RX Audio is gated to the wireline after carrier is detected. 0-1000 msec 150 msec Customer determined
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
3-23
Table 3-8 Channel Configuration Field Definitions (continued) Data Field Description Range/Selection Repeater:
Drop Out Delay Specifies the amount of time repeater mode is maintained following loss of received signal. Specifies the amount of delay before receive audio is gated to the transmitter in repeater applications. 0-2550 sec 2 sec Customer defined. Typically 1 to 5 sec. Customer defined. Typically used in systems with subscriber MDC ID to prevent ID from being repeated.
Default
Audio Hold-Off
0-2550 msec
0 msec
Hear Clear:
Compander Determines whether companding (compression and expansion) is employed for transmit/receive signals. Determines whether receiver noise cancellation is employed. Disabled Enabled Disabled Enabled Disabled Customer determined
Noise Canceller
Disabled
Customer determined
Advanced:
MRTI Operation Specifies whether MRTI (phone patch) feature is enabled or disabled for this channel. Allows polarity of receive signal to be inverted. Specifies priority order of three types of PTT requests: W = wireline R = repeater L = local Examples: W > R: Wireline has priority over repeater R = L: Repeater and local PTT requests have equal priority. Whichever occurs first takes and maintains PTT control. Specifies whether received signal is boosted prior to transmission by repeater. Boost = 150% (3 dB) Example: 2 kHz deviation receive signal is repeated at 3 kHz deviation. Disabled Enabled Disabled Enabled See help Disabled Customer determined
Receive Signal Inversion PTT Priority
Disabled W>R>L
Customer determined Customer defined
Analog Repeater Boost
Enabled Disabled
Enabled
Customer defined
1. If Tx and Rx frequencies are different (as in repeater application), the Tx idle frequency equals the Tx frequency. If the Rx and TX frequencies are equal (as in base station application), the Tx idle frequency is set to a value derived by the following formula: If Tx = Rx and the frequency is divisible by 6.25 kHz with no remainder, then Tx idle = (Tx frequency - 112.5 kHz). Result must be higher than lower limit for band or range. If less than lower limit, Tx idle frequency is calculated as follows: Tx Idle = Tx Frequency + 112.5 kHz. If Tx = Rx and is not divisible by 6.25 kHz, Tx idle is calculated using previous two formulas with 112.5 kHz replaced with 90 kHz. If you change either the Rx of Tx frequency and it results in making the two frequencies equal, a pop-up window appears providing you with the opportunity to let the RSS program calculate the proper Tx idle frequency.
3-24
688 1085E 35-AN
0 6/30 /201 1
PROGRAMMING THE TRC COMMANDS DATA
Programming the TRC Commands Data ...................................

The QUANTAR stations installed in conventional systems are capable of being controlled from a remote console through function tones transmitted over the wireline when the Wireline option is set to the installed wireline module (other than None). The station is capable of detecting a high level guard tone (HLGT) and up to 17 different function tones. Up to eight commands can be associated with the HLGT and each of the 17 function tones. The commands associated with a particular tone are queued for execution after that tone is detected. The station decodes up to two function tones after HLGT is detected. Program the function tones as directed by the system designer, as follows:
1.
Click TRC Command Table in the navigation pane. The TRC Command Table screen appears as shown in Figure 3-12. The TRC Commands screen allows you to define any or all of the 18 function tones by assigning up to eight station commands per tone.
..
Figure 3-12 TRC Command Table Screen
1.
Click the cursor in the desired field to start entering commands through the keyboard. The commands are executed in sequence.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
3-25
PROGRAMMING THE TRC COMMANDS DATA
1 5
2 6
3 7
4 8
2.
For any displayed tone in the TRC Command Table screen: Enter the desired command from Table 3-9 in the cells of that tone, up to eight commands per tone.
NOTE
If the Guard tone is set to a frequency that is within 40 Hz of a function tone, that function tone is blanked and therefore unavailable for use.
3.
Repeat step 2 for all other tones, if required.
Table 3-9 TRC Commands Command

ALARM OFF ALARM ON CHN XXX GATEACC OFF GATEACC ON KEY
Function
Commands station not to route alarm alert tones (over the air and/or over the wireline, as defined on the Channel Information screen. Commands station to route alarm alert tones (over the air and/or over the wireline, as defined on the Channel Information screen. Commands station to tune transmitter and receiver to specified channel. The channel must exist on the Channel Information table. Example: CHN 002. Commands station not to repeat for users with PLs/DPLs assigned with a User Access of Gated on Multi-Coded Squelch screen. Commands station to repeat for users with PLs/DPLs assigned with a User Access of Gated on Multi-Coded Squelch screen. Commands station to key transmitter and remain keyed as long as low level guard tone is received. If a KEY command is queued by the first tone detected, all subsequent tones and their associated commands are ignored until the detection of a subsequent high level guard tone. Commands station to key transmitter indefinitely. Transmitter may be de-keyed by the KEY OFF command. Commands station to de-key transmitter. Commands station to turn on receiver-to-wireline audio path. Overrides all squelch requirements, if any. Not required for QUANTAR/Quantro stations. See Help for details. Disables MRTI (phone patch) feature. MRTI is enabled at station boot. Enables MRTI (phone patch) feature capability. Used to cancel MRTI OFF command. Commands station to turn on appropriate receiver squelch (as programmed in Channel Information screen for the affected channel). Includes CSQ, PL, and DPL. Commands station to turn off appropriate receiver squelch (as programmed in Channel Information screen for the affected channel). Includes CSQ, PL, and DPL. Enables repeater mode (if repeater capable). Station repeats when qualifiers, as programmed in analog Rx Activation field in the Channel Information screen, are met. Disables repeater mode (if repeater capable). Station repeats when qualifiers, as programmed in analog Rx Activation field in the Channel Information screen, are met.
KEY ON KEY OFF MONITOR MORE MRTI OFF MRTI ON RXPL ON RXPL OFF RPT ON RPT OFF
3-26
688 1085E 35-AN
0 6/30 /201 1
PROGRAMMING DC REMOTE COMMAND DATA
Table 3-9 TRC Commands (continued) Command

SCAN ON SCAN OFF SCAN RESUME SCAN SUSPEND SELALARM OFF SELALARM ON
Function
Commands station to begin receiver scanning operation, beginning with first scan-enabled channel in the Channel Scan List. This requires purchase of Scanning Receiver option. Commands station to cease receiver scanning operation. Station remains on the current channel. If receiver scanning has been suspended, this command causes the station to resume receiver scanning operation. If station is in receiver scanning operation, this command stops the scanning process and places the station on the current channel. Commands station to stop sending alarm alert tones for current active alarm over the air and/or over the wireline, as defined on the Channel Information screen. Alarm alert tones for any subsequent alarms are routed normally. Cancels SEALARM OFF command. If SEALARM OFF had been used to silence the alarm alert tones for a currently active alarm, issuing the SEALARM ON command allows the tones to be routed normally over the air and/ or over the wireline, as defined on the Channel Information screen. Commands station to turn on appropriate transmitter squelch code as programmed in Channel Information screen for the affect channel. Includes CSQ, PL, and DPL. Commands station to turn off appropriate transmitter squelch code as programmed in Channel Information screen for the affect channel. Includes CSQ, PL, and DPL. Commands station to wait XXXXX msec before executing the next command. Range is 0-10000 (10 sec).
TXPL ON TXPL OFF WAIT XXXXX
Programming DC Remote Command Data ...................................

QUANTAR and Quantro stations in conventional systems are capable of being controlled by a remote console through a DC current level when: Remote Control Type (on Wireline Configuration screen) is set to DC. Wireline Option (on Hardware Configuration screen) is set to any valid wireline configuration in the selection list.
The station contains decoder circuitry that can interpret detection and undetection of up to six DC current levels: +12.5 mA +5.5 mA +2.5 mA -12.5 mA -5.5 mA -2.5 mA
Each current level may represent up to eight station commands that are performed sequentially by the station. The DC Commands screen allows you to define any or all of the six DC currents, in both Detect and Undetect states, by assigning up to eight station commands per current level. When the tone is generated by a tone remote console, the commands are performed in sequence.
..
3-27
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
PROGRAMMING DC REMOTE COMMAND DATA
Program the DC remote command data as directed by the system designer, as follows:
1.
Click DC Command Table in the navigation pane. The DC Configuration Table screen appears (Figure 3-13).
Figure 3-13 DC Command Table Screen

2.
Click the cursor in the desired field to start entering commands through the keyboard.
1 5
2 6
3 7
4 8
3.
For any displayed tone in the DC Command Table screen, enter the desired command from Table 3-9 in the cells for that current level (up to six commands per current level). Repeat step 2 for all other current levels, if required.
NOTE
The only command that does not apply to DC Remote Commands Data is KEY.
3-28
688 1085E 35-AN
0 6/30 /201 1
PROGRAMMING THE RF CONFIGURATION DATA SCREEN
Programming the RF Configuration Data Screen ...................................

The RF Configuration screen allows you to specify operating parameters and system timing values for the station. The default values programmed into this screen at the factory represent standard typical values, and in most cases, need not be changed. However, all fields are fully editable to accommodate unique system requirements or user-specified values.
..
NOTE
Not applicable to DSIII or QUANTAR data base stations. Click RF Configuration in the navigation pane to access the applicable RF Configuration screen (see Figure 3-14). See Table 3-10 for details on each field.
Conventional
6809 SmartZone/SMARTNET
IntelliRepeater
Figure 3-14 RF Configuration Screens Table 3-10 RF Configuration Data Fields Data field
Repeater Operation Max Deviation
Description
Specifies whether station is operating as a base station or a repeater. Limits the station transmit deviation to a percentage of maximum Tx Rated Deviation set on the Channel Information screen.
Range/ Selection
Base Repeater 0-100%
Default
Base 92%
Recommended Setting (if any

Depends on system design 92% recommended
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
3-29
PROGRAMMING THE RF CONFIGURATION DATA SCREEN
Table 3-10 RF Configuration Data Fields (continued) Data field

Low Speed/PL Deviation
Description
Specifies the deviation for low speed TDATA for 6809 trunking applications.
Range/ Selection
0-25%
Default
17% for 25 kHz 18% for 12.5 kHz Disabled 30 msec 10
Recommended Setting (if any

17% or 18% recommended based on channel bandwidth N/A 30 msec recommended Set time less than or equal to the time specified by the FCC Depends on system configuration Depends on system configuration Customer defined Customer selected feature
Antenna Relay Antenna Relay Delay Call Sign Interval
Specifies whether antenna relay is implemented on station. Specifies the delay to allow relay contacts to close before station transmitter is keyed. Specifies the time interval at which FCC assigned station call sign is broadcast. Specifies that the station starts on the last active channel after a reset. Specifies the channel to which station it is set after a reset. Ignored if Startup on Last Active Channel is enabled. Specifies the number of missed frames before ASTRO message is considered terminated. Specifies whether the Fast Key-Up feature is implemented between the station and external device. If enabled, station transmitter key-up time is shortened to 10-12 msec. See Fast Keyup Feature section in station manual for details.
Disabled Enabled 30-90 msec 1-60 minutes
Startup on Last Active Channel Startup Channel ASTRO Fade Tolerance Fast Key-Up
Disabled Enabled 1-28 1-3 frames Disabled Wideband Aux Tx
Disable 1 3 frames Disabled
ASTRO RDLAP:
Repeat Wireline Drop Out Delay ASTRO Tx Filter Specifies whether RDLAP data is repeated. Specifies the length of transmitter hang time following reception of last RDLAP data block. Affects signal shaping so that the transmitted audio occupies a 25 kHz (wide) or 12.5 kHz (narrow) channel. Disabled Enabled 0-255 sec Wide Pulse Narrow Pulse Enabled 0 sec Wide Pulse Depends on system configuration Depends on system configuration Depends on system configuration. Coordinate with subscriber programming Depends on system configuration
Analog Simulcast Reverse Burst
Specifies whether reverse burst is generated internally by station or by external equipment. For conventional simulcast systems only.
Internal External
Internal
SECURENET:
Rx code Detect Fade Timer Fade EOM Timer Setting determines amount of time following a loss of Rx Data before EOM is sent and call is terminated. For example, due to signal fade. Setting determines length of EOM signal transmitted following expiration of the RX Code Detect Fade Timer. 0-9999 msec 80 msec 80 msec recommended
0-9999 msec
80 msec
80 msec recommended
3-30
688 1085E 35-AN
0 6/30 /201 1
PROGRAMMING THE 6809 TRUNKING INTERFACE DATA
Programming the 6809 Trunking Interface Data ...................................

The 6809 Trunking Interface screen allows you to specify operating parameters and system timing values for stations installed in 6809 trunking systems (as set in the System Type selection list). The default values programmed into this screen at the factory represent standard typical values, and in most cases, need not be changed. However, all fields are fully editable to accommodate unique system requirements or customer-specified values. Click 6809 Trunking Interface in the navigation pane to access the 6809 Trunking Interface screen (see Figure 3-15). See Table 3-11 for the screens data fields.
..
Figure 3-15 6809 Trunking Interface Screen Table 3-11 6809 Trunking Interface Screen Data Fields Data Field
RSTAT Mode
Description
Specifies the conditions for RSTAT to go active.
Range/Selections
Normal: receiver unsquelch Dual CT: dual connect tone (trunking) Disabled Enabled Disabled Enabled Disabled Enabled Disabled Enabled
Default
Normal

Depends on system configuration
Failsoft Line TRC Encode
Specifies whether station has ability to activate failsoft mode. Specifies whether station generates continuous tone (2175 Hz) down wireline when in failsoft mode. Specifies whether station repeats on carrier squelch, instead of connect tones, when in failsoft mode. Specifies whether station requires dual connect tones, instead of single connect tone, when in failsoft mode.
Enabled Disabled
Customer determined Customer determined
Failsoft Carrier Squelch Dual CT Failsoft Only
Disabled
Customer determined
Disabled
Customer determined
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
3-31
PROGRAMMING THE SCAN LIST CONFIGURATION DATA
Table 3-11 6809 Trunking Interface Screen Data Fields (continued) Data Field
Modulation Type Trunking Tickle Source Trunking Tickle Source TDT
Description
Specifies which voice mode is used while in failsoft mode. Specifies the signal source used to indicate whether 6809 central is functioning properly. Specifies the amount of time tickle source must be absent before station considers 6809 central malfunctioning.
Range/Selections
Analog ASTRO TX Data Line Mute Line 1-72 sec
Default
Analog TX Data 1

Depends on system configuration Customer determined If tickle source is TX Data, then one second is recommended If tickle source is Mute Line, then 72 sec is recommended Depends on system configuration Depends on system configuration
CSC Logical Channel Number Rx Discriminator Type
Specifies the logical channel number to which this repeater is assigned. Specifies the Rx Discriminator Audio characteristics for stations at a 6809 trunking site.
1-32 QUANTAR/Micor MSF
1 QUANTAR/ Micor
Programming the Scan List Configuration Data ...................................

The channel scanning feature allows conventional stations and subscribers to continuously scan through a list of channels, looking for carrier activity. If a carrier is detected, the scanning process is suspended. When the carrier is no longer detected, the scanning process resumes. Scanning may be programmed to start automatically on the station reset or under manual control from the console.
..
NOTE
Scanning Receiver must be enabled on the Hardware Configuration screen. The Scan List Configuration screen (Figure 3-16) provides the parameters necessary to determine the channels in the scanning list, set a priority channel, and to set timing periods related to channel scanning.
3-32
688 1085E 35-AN
0 6/30 /201 1
Figure 3-16 Scan List Configuration Screen In general, the data fields in the upper portion of the screen relate to scanning parameters that affect the overall scanning process. The lower portion of the screen is used to select the channels to be included in the scanning list and to determine which channels, if any, are to be used as repeater channels. To access the Scan List Configuration screen, click Scan List Configuration in the navigation pane. See Table 3-12 for the screens data fields. The channels listed in the table (four are shown in Figure 3-16) are the available channels for the particular station. Use this table to enable or disable the scanning feature for the listed channel(s). The data fields in the TX Slave column allow you to set one or more of the scanning channels to act as repeater channels. For example, when the scanning process detects a carrier on a scanning channel, the transmitter is keyed while locked on that channel. Table 3-12 Scan List Configuration Data Fields Data Field
Scan On At Reset Priority Channel
Description
Specifies whether the station initiates the scanning process when reset. Specifies if any channel is used as a priority scanning channel. For example, if channel 3 is specified and there are five channels in the scanning list, then the scanning sequence is: 3-1-3-2-3-3-3-4-3-5-3-1... Instead of specifying a priority channel, this field allows you to use the last active RX, TX, or either RX or TX channels to be the priority channel. Priority Channel must be set to Float. Allows a channel that has been determined to be active during the scanning process but that is busy to be marked. When marked, the scanning process does not wait the normal 250 msec when sampling that channel, but rather waits only the 30 msec required for carrier detection. Specifies the amount of time after a non-priority channel becomes inactive before the scanning process continues.
Range/ Selections
Enabled Disabled None Float <channel #>
Default
Disabled None

Floating Priority
Off RX TX RX + TX Off Normal Priority Normal + Priority
Off
Customer determined
Channel Marking
Off
Customer determined
Scan Delay
0 to 10,000 msec
3000 msec
Customer determined
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
3-33
Table 3-12 Scan List Configuration Data Fields (continued) Data Field
Priority Scan Delay Scan Sample Time
Description
Specifies the amount of time after a priority channel becomes inactive before the scanning process continues. Specifies the amount of time the scanning process listens to each scanning channel for activity before it scans to the next channel. Specifies the amount of time the scanning process listens for PL or DPL after first detecting a carrier on a particular channel. Specifies the amount of time delay to begin the scanning process after the console has issued the resume command. Specifies whether the displayed channel is used for scanning operation. Specifies whether the scan channel acts as a repeater channel, when the scanning process detects a carrier on a scanning channel the transmitter is keyed while locked on that channel.
Range/ Selections
0 to 10,000 msec 20 to 10,000 msec
Default
3000 msec 30 msec

Rx Qualify Time
210 to 0,000 msec
250 msec
Customer determined
Resume Scan Timer Scan TX Slave
0 to 10,000 msec Enabled Disabled Enabled Disabled
2000 msec Disabled Disabled
Customer determined Customer determined Customer determined
3-34
688 1085E 35-AN
0 6/30 /201 1
PROGRAMMING THE INTELLIREPEATER
Programming the IntelliRepeater ...................................

The RSS program allows the user to set up the operating parameters for a station in an IntelliRepeater network. Figure 3-17 shows the IntelliRepeater screens provided in the navigation pane that are discussed in this section and Table 3-13 provides a description of each of the IntelliRepeater fields. The screens are applicable to both IntelliRepeater selections.
Figure 3-17 IntelliRepeater Specific Configuration Screens Table 3-13 IntelliRepeater Screen Fields Field Serial Number Station Name Hardware Platform System Type Description Serial number assigned to the radio by the factory User definable station name Either QUANTAR or Quantro IntelliRepeater 3.0/3.5/4.1 supports either Analog or ASTRO CAI operation IntelliRepeater 2.0.3/2.7E supports either Analog or ASTRO VSELP operation Select Analog, ASTRO CAI or ASTRO (VSELP) Select the Rx Freq Range from the choice list Not used for IR
..
Station Type RX Freq Band 1 RX Freq Band 2
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
3-35
Table 3-13 IntelliRepeater Screen Fields (continued) Field Tx Freq IR Freq Band PA Power Rating Power Supply Battery Type Wireline Wild Card Freq Ref Simulcast External Wattmeter Select the Tx Freq Range Select the Trunking Band allocation type from choice list - Defined by system designer Select the PA Type installed in the radio - use choice list Select Power Supply installed in the radio Select Battery Type connected to the radio Normally set to 4-wire. The 8-wire selection is used when the Enhanced Wild Card Option is purchased Set by user to choice to DISABLED, BASIC or ENHANCED Select the frequency reference used for this radio - see choice list Not applicable to IntelliRepeater Enable if an External Wattmeter is connected to the radio Description
Programming the Site Frequency Parameters

The Site Frequency screen is available only when VHF or UHF Rx and Tx frequency bands are selected in the Hardware Configuration screen. If the IntelliRepeater is operating in a VHF or UHF band then click Site Frequency in the navigation pane to access the Site Frequency screen (Figure 3-18). See Table 3-15 for the screens data fields.
Figure 3-18 Site Frequency Screen
3-36
688 1085E 35-AN
0 6/30 /201 1
Table 3-14 Site Frequency Screen Data Fields Data Field

Block #
Description
VHF and UHF trunking spectrum is divided by FCC into three Rx frequency blocks and three Tx frequency blocks; each block is defined by a base frequency, channel spacing (kHz), and number of channels in the block.
Range/ Selections
Non-editable
Default
Rx - 1 Rx - 2 Rx - 3 Tx - 1 Tx - 2 Tx - 3

non-editable
Base Frequency
User programming for starting frequency of each block of channels for receive or transmit. User Programmable for the FCC allocated channel spacing.
Per each VHF or UHF FCC allocated channel starting frequency 5, 6.25, 10, 12.5, 15, 18.75, 20, 25 (5kHz), 25 (6.25kHz), 30, 31.25, 35, 37.5, 40, 43.75, 50 kHz 0-380
0.00000
As determined by the Station Configuration
Channel Spacing
5 kHz
# of Channels
VHF and UHF trunking spectrum is divided by FCC into 380 possible Rx channels and 380 possible Tx channels (per band).
Programming the Site General Parameters

Click Site General in the navigation pane to access the Site General screen (Figure 3-19). See Table 3-15 for the screens data fields.
Figure 3-19 Site General Screen
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
3-37
Table 3-15 Site General Screen Data Fields Data Field

System ID
Description
A four digit field for entry of the system ID number. A two digit field for entry of the repeater site ID number used to inform zone controller of the site identity. This field allows two choices for the site type. This field specifies the minimum number of repeaters that must be operational before the site is allowed to trunk.
Range/ Selections
0001-FFFF (hex)
Default
0000

As determined by the system configuration, must be the same as TCMS system ID As determined by the system configuration As determined by the system configuration Set to half the number of repeaters at site and rounded to next integer value. For example, for a nine repeater site, set this to 5, for an eight repeater site, set it to 4 As determined by the system configuration
Site ID
1 to 64
Site Type Minimum Repeaters to Trunk
Remote Stand-alone 2 through maximum number of repeaters
Remote 2
Token Repeater Number
In the event that a site with an even number of repeaters suffers a DLAN loss that divides the site in half, this field identifies the number of the repeaters (and therefore the side) that repeats. The other side enters failsoft mode. For example, a site with six repeaters (1-6) and a DLAN loss between 3 and 4 divides the site into two sides (1-3 and 4-6). If the Token Repeater Number is set to 5 then side 4-6 repeats and 1-3 enters failsoft mode. This field allows eight choices: 0 through 7. These correspond to a connect tone frequency. 0 corresponds to 105.9 Hz, 1 corresponds to 76.6 Hz. This field defines receive/transmit ASTRO Network ID (hex). For single station trunked repeater application: Specifies whether station has capability to temporarily drop control channel operation and become a voice channel. Effectively varies the time frame in which a subscriber for service (ISW) can be successfully received. Setting to a smaller range limits access by subscribers farther from site while also increasing chances of false service requests caused by random RF noise. For IntelliRepeater 2.0.3/2.7E: Failsoft Modulation is on the Site General Screen because failsoft modulation is the same for all the channels. Specifies which voice mode is used while in failsoft mode. The following apply to ASTRO CAI Capable IntelliRepeaters only: V.24 Hybrid: Used for mixed mode, analog, and ASTRO systems, where the V.24 interface is used for ASTRO and control, and the Line 1/Line 2 wirelines are used for analog. Used only in trunked systems. V.24 Only: Used for ASTRO only systems where the external connection is either local or through microwave link.
1 through maximum number of repeaters
Connect Tone
Use Help or refer to Appendix XXX.
105.9
As determined by the system configuration and must match the connect tone set in the subscribers Depends on system design Customer determined
ASTRO Rx/Tx Access Code Voice on control
000-FFF (hex) Enabled Disabled
293 Disabled
Maximum Control Channel Range
25 to 595 miles
<75 miles (125 km)
Customer determined
Failsoft Modulation Type
Analog ASTRO
Analog
Depends on system configuration
Wireline Interface
V.24 Only V.24 Hybrid
V.24 Hybrid
Customer determined
3-38
688 1085E 35-AN
0 6/30 /201 1
Table 3-15 Site General Screen Data Fields (continued) Data Field
V.24 External Transmit Clock
Description
Specifies whether external synchronization is required for transmit signal. Typically in installations where station and console are connected through a microwave link, RS232 Wireline Interface is used. This defines the parity used to detect communication error with the zone controller.
Range/ Selections
Disabled Enabled
Default
Disabled

Customer determined
Zone Controller Link Parity
Odd Even
Odd
Customer determined
Programming the Site Timer Screen

Click Site Timer in the navigation pane to access the Site Timer screen (Figure 3-20). See Table 3-16 for the screens data fields.
Figure 3-20 Site Timer Screen Table 3-16 Site Timer Screen Data Fields Data Field
Link Recovery
Description
Sets the delay time before noting the loss or recovery of the data link between the station and zone controller and the time before exiting failsoft operation after a link recovery. Sets the delay time before taking a station out of service after a carrier malfunction is detected. Sets the time a station waits for radio handshakes to be established before leaving the assigned channel.
Range/Selections
15-99 seconds
Default
15

As determined by system configuration
Carrier Malfunction Carrier
1-254 seconds (when set to 254, time delay is infinite) 100-6300 msec
50 500
As determined by system configuration As determined by system configuration
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
3-39
Table 3-16 Site Timer Screen Data Fields (continued) Data Field
Message Trunk Fade
Description
Sets the time the station waits before dekey after receiving the disconnect tone. Sets the wait time before deassigning a channel after handshakes are lost but no disconnect tone is received.
Range/Selections
100-6300 msec 100-6300 msec
Default
1000 1200

As determined by system configuration As determined by system configuration
Programming Radio Modulation Partition Screens

Click Radio Modulation Partition in the navigation pane to access the Radio Modulation Partition screen. See Figure 3-21 for these screens. See Table 3-18 for the screens data fields.
Figure 3-21 Radio Modulation Partition Screen Table 3-17 Radio Modulation Partition Screen Data Fields Data Field
ID Block Hex ID Low Hex ID High Modulation
Description
A sequential number that represents a given ID range This represents the low byte of the ID range This represents the high byte of the ID range Specifies which Modulation to use for the selected block
Range/Selections
Default

Depends on system design Depends on system design Depends on system design
ASTRO Analog
Analog
3-40
688 1085E 35-AN
0 6/30 /201 1
Programming Full/Sub Band Partition Screens

To access the Full/Sub Band Partition screen, click Full/Sub Band Partition in the navigation pane. See Figure 3-22 for these screens. See Table 3-18 for the screens data fields.
Figure 3-22 Full/Sub Band Partition and Radio Modulation Partition Screen Table 3-18 Full/Sub Band Partition Screen Data Fields Data Field
ID Block Hex ID Low Hex ID High Block Range
Description
A sequential number that represents a given ID range This represents the low byte of the ID range This represents the high byte of the ID range
Range/Selections
Default

Depends on system design Depends on system design Depends on system design
Full Band Sub Band
Full Band
Programming Repeater Summary Screen

This screen allows you to reorder the IntelliRepeaters at the site. To access the Repeater Summary screen, click Repeater Summary in the navigation pane. See Figure 3-23.
Figure 3-23 Repeater Summary Screen
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
3-41
Programming the Repeater Information Screen

Click Repeater Information in the navigation pane to access the Repeater Information screen (see Figure 3-20). See Table 3-16 for the screens data fields.
Figure 3-24 Repeater Information Screen - Basic Tab
Figure 3-25 Repeater Information Screen - Advanced Tab
3-42
688 1085E 35-AN
0 6/30 /201 1
Table 3-19 Repeater Information Screen Data Fields Data Field Description Range/Selections Basic Tab:
Repeater Number Serial Number Base Repeater Rx Frequency Base Repeater Tx Frequency Base Station Identification Control Channel Capability Identifies the repeater number selected through this screen. This field shows the serial number of the station to which this screen applies. Receive frequency in KHz for the selected repeater. 1-28 digits 1 to 10 digits Follows input of Base Repeater Tx Frequency Depends on band Up to eight alpha-numeric characters in length Enabled Disabled 1 123ABC6789 45 MHz less than Tx frequency 851.0125 MHz None As determined by the system configuration Depends on the system design Non-editable
Default
Transmit frequency in MHz for the selected repeater. The Morse Code ID for the station. An entry must be provided if BSI Capability is set to Enabled. Indicates whether the station is capable of operating as a control channel station.
Depends on the system design Assigned by FCC. Refer to system design document Enabled if station is to be used as a control channel, if not it is disabled As determined by the system design As determined by the system design
Disabled
Preferred Control Channel Rank Dispatch Capability
Assigns preference level for channels use as the control channel. Indicates whether the station can make dispatch calls.
0-4 (0 = disabled) Disabled Analog ASTRO Analog/ASTRO Enabled Disabled Enabled Disabled Enabled Disabled 12 Kb ASTRO Secure Disabled Enabled Disabled Enabled Disabled Analog ASTRO
4 Analog
Failsoft Capability BSI Capability
Indicates whether the repeater can operate in the failsoft mode. Indicates whether the repeater can operate in the BSI operating mode. If set to Enabled, an entry must be provided for Base Station Identification. Indicates whether repeater is capable of dynamic frequency blocking. Indicates whether the repeater is capable of operating as a secure station. Prevents the station from being assigned as a control channel or to a dispatch call unless it is the only repeater available. Indicates whether the repeater can operate at subband frequencies. Allows system to be optimized for more efficient call steering. For IntelliRepeater 3.0/3.5/4.1: Failsoft Modulation is on the Site Repeater Screen because failsoft modulation can be set individually for each channel. Specifies which voice mode is used while in failsoft mode.
Disabled Disabled
As determined by the system design As determined by the system design As determined by the system design As determined by the system design As determined by the system design As determined by the system design Depends on the system configuration
DFB Capability Secure Capability Protect Capability
Disabled Disabled Disabled
Subband Capability Failsoft Modulation Type
Disabled
Analog
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
3-43
Table 3-19 Repeater Information Screen Data Fields (continued) Data Field Description Range/Selections Advanced Tab:
Modulation Type Specifies the type of modulation for current channel. The selections provided depend on the Station Type selected in the Hardware Configuration screen. Tx Rated Deviation Receive Channel BW Specifies the maximum frequency deviation allowed in channel. Specifies the frequency spacing (in kHz) between channels. Analog ASTRO Analog/ASTRO ASTRO RX WIDE DEV Secure XL Analog/Sec XL Secure CFB Analog/Sec CFB Analog CAI Analog/ASTRO CAI CAI Rx Wide Dev Analog if Station Type is Analog Analog/ ASTRO if Station Type is ASTRO Capable As determined by the system design
Default
5.00 kHz 4 kHz 2.5 kHz Wide (25-30 kHz) NPSPAC (25 kHz) Narrow (12.5-15 kHz) Narrow (12.5 kHz)
5.00 kHz
Determined by FCC per channel type. Depends on the system design Determined by FCC per channel type. Depends on the system design Refer to system design document for FCC licensed power rating
Wide
Tx Power Out
Specifies the output power from the station power amplifier module. This field is limited to a predetermined output power level if the station is equipped with the Limited Output Power option. Specifies the output power from the station power amplifier module when in battery backup mode.
Quantro: 50% to 110% QUANTAR: 25% to 110% of the stations power rating Quantro: 50% to 110% QUANTAR: 25% to 110% of the stations power rating Enabled Disabled Enabled Disabled
The full power selected in PA Power Rating
Tx Power Out Battery Backup
50% of value selected in PA Power Rating
Customer defined. Set to lower value to extend station operation in battery backup mode Customer defined Customer defined
Rcv Signal Inversion Analog Repeater Boost
Allows polarity of receive signal to be inverted. Specifies whether the received signal is boosted prior to transmission by repeater. Boost = 150% (3 dB). Example: 2 kHz deviation receive signal is repeated at 3 kHz deviation. Determines whether the companding (compression and expansion) is employed for transmit/receive signals. Determines whether the receiver noise cancellation is employed.
Disabled Disabled
Compander
Enabled Disabled Enabled Disabled
Disabled
Applies to 900 MHz only. Must be enabled for 900 MHz stations Must be enabled for 900 MHz stations. Customer determined
Noise Canceller
Disabled
Programming RF Configuration
Click RF Configuration in the navigation pane to access the RF Configuration screen. See Figure 3-26 and Figure 3-27 for views of the RF Configuration screens. See Table 3-20 for the screens data fields.
3-44
688 1085E 35-AN
0 6/30 /201 1
Conventional - Analog
Conventional - ASTRO
Figure 3-26 RF Configuration Screen - Conventional Stations
IntelliRepeater - Analog
IntelliRepeater - ASTRO
6809 Trunking - Analog
6809 Trunking - ASTRO
Figure 3-27 RF Configuration Screen - IntelliRepeater and 6809 Trunking Stations
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
3-45
PROGRAMMING THE CODEPLUG DATA INTO A CONVENTIONAL OR 6809 STATION OR ASTRO-TAC COMPARATOR
Table 3-20 RF Configuration Data Fields Data Field

Repeater Operation Max Deviation
Description
This specifies whether the station is used as a base station or repeater. Limits the station transmit deviation to a percentage of maximum as set on the Channel Information screen. Specifies deviation for low speed TDATA for 6809 trunking applications. This specifies whether the antenna relay is in use. Specifies time intervals at which FCC assigned station call sign is broadcast. Specifies that the last active channel is used as the current startup channel if enabled. Otherwise, the startup channel is specified in the Startup Channel field. Specifies the channel selected as the Startup Channel after reset. Specifies the number of missed frames before ASTRO message is considered. Selects the ASTRO transmit modulation filter to be used. Specifies the appropriate simulcast reverse burst. Specifies whether ASTRO RDLAP data is repeated. Specifies the amount of hang time added to the end of an RDLAP and ASTRO CAI WL transmission.
Range/ Selections
Base Repeater 0-100% Base 92%
Default

Depends on system configuration 92% recommended
Low Speed/PL Deviation
0-25%
17% for 25 kHz 18% for 12.5 kHz Disabled 60 min.
Use value shown for the bandwidth in use Depends on system configuration Set time less than or equal to the time specified by the FCC Depends on system configuration
Antenna Relay Call Sign Interval
Enabled Disabled 1-60 minutes
Startup on Last Active Channel
Enabled Disabled
Disabled
Startup Channel ASTRO Fade Tolerance
1 to 16 1-3 frames
1 3 frames
Depends on system configuration Customer defined
ASTRO Tx Filter Analog Simulcast Reverse Burst Repeat Wireline Drop Out Delay
Wide Pulse Narrow Pulse Internal External Enabled Disabled 0-999 seconds
Wide Pulse Internal
System dependent System dependent (for conventional simulcast only) System dependent System dependent
Disabled 0 sec
Programming the Codeplug Data into a Conventional or 6809 Station or ASTRO-TAC Comparator ...................................
After saving the codeplug data to an archive file on the PC hard disk, you must program the codeplug data into a conventional or 6809 stations codeplug.
..
3-46
688 1085E 35-AN
0 6/30 /201 1
PROGRAMMING THE CODEPLUG DATA INTO A CONVENTIONAL OR 6809 STATION OR ASTRO-TAC COMPARATOR
NOTE
When programming the codeplug, you may be asked whether you want to condition the codeplug. Follow the instructions in the message window to perform this task. Conditioning is required only once. With the PC connected and the RSS program running, perform the following to program data into the station codeplug:
1.
Fom the File menu, select Write to Device, or Write to Device icon on the toolbar.
File/Write to Device Menu Item
Save file icon
A confirmation window appears.
2.
Click Yes. The progress of the write operation appears. When the operation is complete, an RSS message window asks whether you would like to reset the device.
3.
Click Yes to reset the device to activate the codeplug you just wrote to the device. A message window appears stating that a reset is in progress.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
3-47
PROGRAMMING THE CODEPLUG DATA INTO AN INTELLIREPEATER STATION INSTALLED IN A SMARTZONE 2.0.3 OR 2.7E SYSTEM
4.
Click Continue. On reset the following window is opened.
5.
Click Continue. The main RSS window appears.
Programming the Codeplug Data into an IntelliRepeater Station Installed in a SmartZone 2.0.3 or 2.7E System ...................................
..
NOTE
1.
From the File menu, select Write to Device, or click Write to Device icon on the toolbar.
3-48
688 1085E 35-AN
0 6/30 /201 1
RADIO SERVICE SOFTWARE INSTRUCTION MANUAL SYSTEM
PROGRAMMING THE CODEPLUG DATA INTO AN INTELLIREPEATER STATION INSTALLED IN A SMARTZONE 2.0.3 OR 2.7E
Save file icon
2.
Click Yes. After a few seconds, the following Please Enter the Start Up Channel window appears.
3.
Verify that the displayed channel is the start up channel. Change if required. Then click Next >>. A message window appears asking for verification of the Startup Channel and the serial number.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
3-49
PROGRAMMING THE CODEPLUG DATA INTO AN INTELLIREPEATER STATION INSTALLED IN A SMARTZONE 2.0.3 OR 2.7E SYSTEM
4.
Click Yes to start the codeplug write operation. The progress of the write operation appears. When the operation is complete, an RSS message window asks whether you would like to reset the device.
5.
Click Yes to reset all connected IntelliRepeaters to activate the codeplug. A message window appears stating that a reset is in progress.
3-50
688 1085E 35-AN
0 6/30 /201 1
RADIO SERVICE SOFTWARE INSTRUCTION MANUAL PROGRAMMING THE CODEPLUG DATA INTO AN INTELLIREPEATER STATION INSTALLED IN A SMARTZONE 3.0, 3.5, OR 4.1 SYSTEM
6.
Click Continue. On reset, the following window appears.
7.
Click Continue. The display returns to the main RSS window.
Programming the Codeplug Data into an IntelliRepeater Station Installed in a SmartZone 3.0, 3.5, or 4.1 System ...................................
..
NOTE
1.
From the File menu, select Write to Device, or click Write to Device icon on the toolbar.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
3-51
PROGRAMMING THE CODEPLUG DATA INTO AN INTELLIREPEATER STATION INSTALLED IN A SMARTZONE 3.0, 3.5, OR 4.1 SYSTEM
Save file icon
2.
Click Yes. After a few seconds the following crossload message window appears.
3.
Click Yes to write the codeplug to the connected IntelliRepeater station and then have that station load on each IntelliRepeater connected to it with the codeplug. The following Please enter the desired time and date window appears.
3-52
688 1085E 35-AN
0 6/30 /201 1
RADIO SERVICE SOFTWARE INSTRUCTION MANUAL PROGRAMMING THE CODEPLUG DATA INTO AN INTELLIREPEATER STATION INSTALLED IN A SMARTZONE 3.0, 3.5, OR 4.1 SYSTEM
4. 5.
Enter the current date and time. When complete, click Next. The following Please Enter the Start Up Channel window appears.
6.
Verify that the displayed channel is the start up channel. Change if required. Then click Next>>. Click Yes to start the codeplug write operation. The progress of the write operation appears. When the operation is complete, an RSS message window asks whether you would like to reset the device.
7.
8.
Click Yes to reset all connected IntelliRepeaters to activate the codeplug. A message window is opened stating that a reset is in progress.
9.
Click Continue. On reset, the following window is opened.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
3-53
PERFORMING STATION ALIGNMENT
10.
Click Continue. The display returns to the main RSS window.
Performing Station Alignment ...................................

Some of the station tuning, alignment, and adjustment tasks have been performed in the factory prior to shipment. These procedures do not need to be performed at the time of installation and are generally required only after maintenance of certain modules. These procedures are listed below with their location in this manual. Aligning Power Output Procedure on page 6-4 Aligning Power Output Procedure for a Quantro 350W VHF Station on page 6-7 Aligning Tx Deviation Gain Adjust Procedure, 350W VHF Stations on page 6-11 Aligning Reference Modulation Compensation Procedure on page 6-14
Certain site-specific alignment tasks must be performed during optimization at the time they are installed and prior to being placed into service. The tasks required are shown below: RX and TX Wireline Alignment on page 3-55 Aligning Radio Signal Strength Indicator (RSSI) on page 3-68 Aligning Squelch Adjust Procedure on page 3-71 Equalizing Batteries on page 3-73 Calibrating Reference Oscillator Procedure on page 3-75 Setting ASTRO Tx Align and Test Procedure on page 3-82 Generating ASTRO Test Patterns on page 3-85 TDATA Calibration (6809 Trunking Station Only) on page 3-88 ASTRO Bit Error Rate Reports on page 3-90
..
IMPORTANT
Before performing any of the station alignment procedures, you must dekey the station transmitter. In addition, when you enter the Alignment Screen, the following prompt is displayed, "The station is Automatically put into Access Disable mode. A station reset is required to return the station to Access Enable. Do you want to continue?" Click Yes to continue. When the alignment procedures are completed, deactivate Access Disable and restore the station to normal operation by performing a station reset.
3-54
688 1085E 35-AN
0 6/30 /201 1
IMPORTANT
When entering data in any of the alignment screen fields, you must click Save to save the value to the station. If you enter a parameter value and exit the alignment screen without saving the value, the station continues to operate using the previous value.
NOTE
If you experiment with a parameter value without intending to permanently change the value stored in the station, do not click Save and reset the station to restore the original parameter value(s).
Required Test Equipment

The following test equipment is required for optimization: Motorola R2001 communications analyzer (or equivalent) Motorola R2600 communications analyzer (or equivalent) Motorola R2650 ASTRO communications analyzer (or equivalent)
RX and TX Wireline Alignment

The station may be equipped with a 4-wire or 8-wire wireline interface board. Depending on the system application and the specific wireline board, the following wireline circuit configurations are supported: 2-wire half duplex 4-wire half duplex 4-wire full duplex 6-wire full duplex 8-wire full duplex
Alignment of the receive (Rx) and transmit (Tx) circuits is required depending on the system application, wireline circuit configuration, and whether equalization is required or desired. Use Table 3-21, Table 3-22, and Table 3-23 to determine the Rx and Tx lines that require alignment and/or equalization and the specific alignment procedure(s) to perform. The following examples show you how to use the tables: Example 1: For a station programmed for 4-wire operation, ALC disabled, and not in a voting system, Table 3-21 shows that Line 1 requires alignment procedure E and Line 2 requires alignment procedure A. Equalization is optional because the station is not in a voting system.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
3-55
Example 2: For a station programmed for 4-wire operation, ALC enabled, and in a voting system, Table 3-21 shows that Line 1 requires no alignment and that Line 2 requires alignment procedure A. The Equalization Matrix shows that Line 2 also requires alignment procedures B, D, and C (if needed). Example 3: For a station programmed for 8-wire operation and ALC enabled, Table 3-21 shows that Line 1 requires alignment procedure E, Line 2 requires alignment procedure A, Line 3 requires no alignment, and Line 4 requires alignment procedure A.
Table 3-21 RX/TX Wireline Alignment Matrix Wireline Circuit Configuration1

2-wire
Automatic Level Control (ALC)

Off On
Alignment Procedure Required L1 (TX)

Note 2
L2 (RX)
A and E A and E
L3 (TX)
N/A
L4 (RX)
N/A
4-wire
Off On
E None E E E E
A A A A A A
N/A
N/A
6-wire
Off On
E None E None
N/A
8-wire
Off On
A A
Notes: 1. The 2, 4, 6, and 8-wire configurations provide direct connection to a console. Stations in voting systems must be configured for 4-wire configuration. 2. For 2-wire configurations, Rx and Tx alignments are both performed on Line 2.
Table 3-22 RX/TX Wireline Equalization Matrix Equalization Required for Voice or Status Tone (station in voting system)
Voice

N/A
L2 (TR)
B C (if required)
L3 (TX)
N/A
L4 (RX)
None
Status Tone
N/A
N/A
None
Table 3-23 RX Wireline ASTRO Link Management Tone Alignment Matrix Alignment Required for ASTRO Station with Hybrid Link
Link Management Tone

N/A
L2 (TR)
F
L3 (TX)
N/A
L4 (RX)
N/A
3-56
688 1085E 35-AN
0 6/30 /201 1
Procedure A: Rx Wireline Alignment Procedure

1. 2. 3.
Disconnect the stations receive antenna cable. Launch the RSS program as outlined in Launching the RSS Program on page 2-12. Read the stations codeplug as outlined in Reading the Device Codeplug on page 2-14. You are now connected to the station. Click the + sign next to Service to expand the Service menu. Click Alignment Screen in the navigation pane.
4. 5.
6.
Click Yes to continue.
NOTE
When the alignment procedures are completed, deactivate Access Disable and restore the station to normal operation by performing a station reset. The Reference Oscillator Alignment screen appears.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
3-57
7. 8.
Click RX Wireline (Line 2) tab, a confirmation window appears. Click Yes. The Rx Wireline (Line 2) screen appears.
3-58
688 1085E 35-AN
0 6/30 /201 1
9.
In the Rx Wireline Level (1 kHz) field: Enter the wireline level desired for a received RF signal at 60% of the rated system deviation. Typically, the wireline level is defined in your systems design document. The allowable range is -20 to 0 dBm. Click Save. The station automatically adjusts for the Rx wireline level you entered and stores the value in station memory.
10.
NOTE
Pressing the Enter key does not save the entered value to the station.
11.
Repeat this procedure for Rx Wireline (Line 4) if applicable.
Procedure B: Rx Wireline Equalization Alignment Procedure

This procedure applies only for a station that is part of a receiver voting system, such as SpectraTAC, Digi-TAC, or ASTRO-TAC. To adjust for Rx Wireline equalization, perform the following procedure.
NOTE
If the comparator and station are not collocated, then two technicians are required to perform this procedure, one at the comparator and one at the station.
1.
At the comparator, connect a high-impedance AC voltmeter across the phone line input corresponding to the station/receiver being aligned. Launch the RSS program as outlined in Launching the RSS Program on page 2-12. Read the stations codeplug as outlined in Reading the Device Codeplug on page 2-14. You are now connected to the station. Click the + sign next to Service to expand the Service menu. Click Alignment Screen in the navigation pane.
2. 3.
4. 5.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
3-59
6.
NOTE
3-60
688 1085E 35-AN
0 6/30 /201 1
7.
Click the RX Wireline (Line 2) tab. The Rx Wireline (Line 2) screen appears.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
3-61
8.
Click Tone On, to cause the station/receiver to generate a 1 kHz test tone (at the level specified in Procedure A: Rx Wireline Alignment Procedure on page 3-57). Measure (in dBm) and record the value as indicated on the AC voltmeter connected to the comparator.
9.
Click Tone Off near the bottom of the pane.
Local Oscillator Boost Equalization (Optional)

10.
Click Tone On for Local Oscillator (LO) Boost Adjust Level @ 400 Hz in the Rx Wireline Equalization section, to cause the station/receiver to generate a 400 Hz alignment tone. Measure (in dBm) and record the value.
11. 12.
Click Tone Off near the bottom of the pane. Subtract the absolute value measured in step 8 from the absolute value measured in step 10 and enter the result in LO Boost Adjust Level @ 400 Hz Current field. Example: -22.8 dBm measured in step 8. -25.4 dBm measured in step 10. 25.4 - 22.8 = 2.6 (if the result is negative, use 0) Enter 2.6 in LO Boost Adjust Level @ 400 Hz Current field.
Hi Boost Level Equalization NOTE

In most cases, the default 2500 Hz Hi Boost Frequency is acceptable. If the telephone lines exhibit a notch or peak at 2500 Hz, you may need to change the boost frequency by entering another frequency, such as between 2200 Hz and 2800 Hz, in the Hi Boost Frequency field and then click the Set Freq.
13.
Click Tone On, to cause the station/receiver to generate a 1 kHz test tone (at the level specified in Procedure A: Rx Wireline Alignment Procedure on page 3-57). Measure (in dBm) and record the new value as indicated on the AC voltmeter connected to the comparator.
3-62
688 1085E 35-AN
0 6/30 /201 1
14.
Click Tone On for HI Boost Adjust Level @ 2500 Hz in the Rx Wireline Equalization section, to cause the station/receiver to generate a 2500 Hz alignment tone. Measure (in dBm) and record the value.
15. 16.
Click Tone Off near the bottom of the pane. Subtract the absolute value measured in step 13 from the absolute value measured in step 14 and enter the result in LO Boost Adjust Level @ 400 Hz Current field. Example: -22.8 dBm measured in step 13. -27.5 dBm measured in step 14. 27.5 - 22.8 = 4.7 (if the result is negative, use 0) Enter 4.7 in HI Boost Adjust Level @ 2500 Hz Current field.
17.
After all equalization settings have been entered, click Save at the bottom of the pane to save the values to non-volatile memory in the station.
Procedure C: Status Tone Level Alignment Procedure

This procedure is required only for stations in the following configurations: SPECTRA-TAC voting systems Digi-TAC voting systems IntelliRepeater stations
Status tone level alignment is used to set the analog monitor tone level for ASTRO systems using hybrid links.
NOTE
0 dB status tone is not supported by QUANTAR and Quantro stations.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
3-63
NOTE
Although status tones are not used in IntelliRepeater systems, status tone level equalization must be performed to allow system line tests.
1.
Click Tone On to generate a 2175 Hz alignment status tone. Measure (in dBm) and record the value. Click Tone Off near the bottom of the pane. Subtract the absolute value measured in step 13 of Procedure B from the absolute value measured in step 1 of this procedure, and subtract 21.6 (for 13 dB status tone system) from the result. Enter the result in Status Tone Level Current field. Example: -22.8 dBm measured in step 13. -31.9 dBm measured in step 1. 31.9 - 22.8 = 9.1 9.1 - 21.6 = -12.5 Enter -12.5 in Status Tone Level Current field.
2. 3.
4.
After all equalization settings have been entered, click Save to save the values to nonvolatile memory in the station.
Procedure D: Optional Hi Boost Fine Tuning Procedure

The voting algorithm in a receiver voting system depends on the flatness of the received audio signal between 2000 Hz and 3000 Hz. This flatness is affected by the frequency and amplitude response of the phone lines between the receiver and the comparator. There may be some cases where the Hi Boost equalization procedure (Procedure B: Rx Wireline Equalization Alignment Procedure on page 3-59) does not result in the optimum boost setting. This is usually indicated by a high amount of wrong site voting (resulting in poor audio quality). If the system exhibits a significant amount of wrong site voting, first check the phone lines and ensure that they meet the required specifications. If within specifications, the following procedure is provided to allow you to fine tune the Hi Boost level setting to improve voting accuracy.
1.
Click the RX Wireline (Line 2) tab. The Rx Wireline (Line 2) screen appears.
3-64
688 1085E 35-AN
0 6/30 /201 1
2.
At the comparator, connect a high impedance AC voltmeter across the phone line input corresponding to the station/receiver being aligned. Click Tone On for 2200 Hz and record the value displayed on the voltmeter. Click Tone Off. Click Tone On for 2500 Hz and record the value displayed on the voltmeter. Click Tone Off. Click Tone On for 2800 Hz and record the value displayed on the voltmeter. Click Tone Off. Calculate the mathematical average of the three voltmeter readings and compare the result to the value measured in step 13 of Procedure B: Rx Wireline Equalization Alignment Procedure on page 3-59. Example: 2200 Hz Level: -21.9 dBm 2500 Hz Level: -22.8 dBm 2800 Hz Level: -23.7 dBm Total = -68.4 dBm -68.4 3 = -22.8 dBm
3. 4. 5. 6. 7. 8. 9.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
3-65
Because -22.8 dBm is equal to the value measured in step 13 of Procedure B: Rx Wireline Equalization Alignment Procedure on page 3-59, the equalization may be considered optimally set and no further action is required. However, if the result in the above calculation is different than the value measured in step 13 of Procedure B: Rx Wireline Equalization Alignment Procedure on page 3-59, the Hi Boost Adjust Level, proceed to step 10.
10.
Subtract the average, as calculated above, from the value measured in step 13 of Procedure B: Rx Wireline Equalization Alignment Procedure on page 3-59. Add the value from the previous step to the value currently displayed in the Hi Boost Adjust Level field. In this case: 23.2 dBm - 22.8 dBm = 0.4 dBm 0.4 dBm + 4.7 dBm = 5.1 dBm
11.
12. 13. 14.
Enter 5.1 in the Hi Boost Adjust Level current field. Click Save. Repeat steps 3 through 13 until the value measured in step 13 of Procedure B: Rx Wireline Equalization Alignment Procedure on page 3-59 and the average of the 2200, 2500, and 2800 Hz measurements are equal. If the preceding procedure does not produce an optimally equalized phone line, repeat the procedure using five evenly spaced alignment tones, such as 2200, 2350, 2500, 2650, and 2800 Hz.
Procedure E: Aligning TX Wireline Procedure

1.
If present, disconnect the phone line connected at the orange screw terminal, otherwise proceed to the next step. If phone line connections have been made through the 50-pin Telco connector, disconnect it, otherwise proceed to the next step. Click the TX Wireline tab. The TX Wireline screen appears.
2.
3.
3-66
688 1085E 35-AN
0 6/30 /201 1
4.
Connect the signal generator to the station as shown in Figure 3-28.
PHONE LINE INPUTS

1 LINE 1 + 2 LINE 1 3 LINE 2 + 4 LINE 2 5 6 7 8 LINE 3 + LINE 3 LINE 4 + LINE 4 -
1 kHz tone @ level you wish to result in 60% of

rated system deviation (defined in system design document)
MON OUT
Figure 3-28 TX Wireline Alignment Setup
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
3-67

5.
For 2-wire audio circuits: Line 2 is used for both receive and transmit. For 4-wire phone line circuits: Line 1 is used for transmit audio. For 6-wire and 8-wire phone line circuits: Line 1 and Line 3 are used for transmit audio. Click Tx Wireline 1 Calibration. The station automatically adjusts for the TX Wireline level and stores the value(s) in memory.
Procedure F: Aligning ASTRO Link Management Tone Procedure

This procedure is required only for ASTRO stations with hybrid links, including conventional, 6809 trunking, and IntelliRepeater trunking.
1.
Click Rx Wireline (Line 2) tab. The Rx Wireline (Line 2) screen appears.
2.
Set the Status Tone Level as required by the System Installation Guidelines (typically -10 dBm). This example shows a setting of -13 dBm.
Aligning Radio Signal Strength Indicator (RSSI)

1.
Connect the station to the communications analyzer as shown in Figure 3-29.
3-68
688 1085E 35-AN
0 6/30 /201 1
TO RECEIVE ANTENNA
STATION RECEIVE INPUT R2001 COMMUNICATIONS ANALYZER
Figure 3-29 RSSI Alignment Test Setup

2.
Click the RSSI Calibration tab. The RSSI Calibration screen appears.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
3-69
3.
Turn the communications analyzer on and set it as follows: Generate Frequency: Set the stations receive frequency Output level: -90 dBm Modulation: None
4. 5.
Click Select RX1 Channel. Click Start RSSI Calibration. The station automatically calibrates the receiver circuitry and stores the setting in station memory. If the station is equipped with two receiver modules: Click Select RX2 channel. Otherwise: you have completed this procedure. Change the frequency on the communications analyzer to that of the second receive channel. Click Start RSSI Calibration. The station automatically calibrates the receiver circuitry and stores the setting in station memory.
6.
7.
8.
3-70
688 1085E 35-AN
0 6/30 /201 1
Aligning Squelch Adjust Procedure

1.
Connect the station as shown Figure 3-30.

TO RECEIVE ANTENNA
Figure 3-30 Squelch Adjust Alignment Setup

2.
Set the communications analyzer as follows: Frequency: Set to the stations receive frequency. Output level: Set as specified in the system design document. Typically, set to 12 dB SINAD or 20 dB quieting RF level. Modulation: None
3.
Click the Squelch Adjust tab. The Squelch Adjust screen appears.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
3-71
4. 5.
Click Select Receiver 1. Click the triple arrows pointing to the left to set the squelch to fully open.
6.
Turn on the stations local speaker and verify that you can hear carrier noise. If you hear carrier noise proceed to the next step. If you do not hear carrier noise, resolve the problem before proceeding.
7.
Use the right pointing arrows to set the squelch until the noise is squelched. Wait atleast one second between each arrow click to allow the squelch circuitry to adjust.
NOTE
The single arrow moves the squelch by single units, the double arrow by 7 units, and the triple all the way to 100% (tight).
3-72
688 1085E 35-AN
0 6/30 /201 1
8.
When the carrier noise is squelched, use the left pointing arrows to adjust the squelch toward open until carrier noise is again heard. Wait at least one second between each arrow click to allow the squelch circuitry to adjust. Click Save. The squelch setting is saved to the station. If the station has two receivers, click Select Receiver 2 and perform steps 7 through 9. Otherwise squelch setting is complete.
9. 10.
NOTE
Trunking stations (IntelliRepeater or 6809 SMARTNET/SmartZone stations) must be configured for mixed mode, ANALOG/ASTRO CAI, operation in order for them to detect interfering carriers. The threshold for detecting the interfering carrier is set by performing the Carrier Squelch alignment. A station that is configured for ASTRO CAI only operation does not perform the carrier detect function properly.
Equalizing Batteries
Sites equipped with storage batteries to provide station power in case of primary power failure require the battery cells be equalized periodically. It is recommended that the batteries be equalized at the time of installation, and henceforth according to the schedule recommended by the battery manufacturer. Battery equalization is a process under which the charging voltage to the batteries is slightly boosted for a period of time, typically 48 hours to 72 hours. This slight overcharging causes the individual cells to regenerate equally and provide nearly identical output voltages.
For QUANTAR Stations:

1.
Click the Battery Equalization tab. The Battery Equalization screen appears.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
3-73
2.
Click Turn Equalization On to start the process.
The station power supply boosts battery charging voltage slightly for a period of time determined by the type of batteries being used, as specified in the Hardware Configuration screen. A timer in the station controls the length of time that the boosted charging voltage is applied and automatically sets the charging voltage to its normal level when the timer expires.
3.
If you must stop the process manually, click Turn Equalization Off.
3-74
688 1085E 35-AN
0 6/30 /201 1
For Quantro Stations: NOTE

Battery equalization for Quantro stations is performed manually. To equalize the batteries in a Quantro station, perform the following procedure:
1.
Toggle the Float/Equalize switch located on the power supply control board to the Equalize position. Time the boosted charging period yourself. When the appropriate time has expired, toggle the switch to the Float position.
2. 3.
Calibrating Reference Oscillator Procedure

The circuit device(s) that set the stations reference frequency exhibit slight variations in operating characteristics over time. Approximately 90% of these variations occur in the first year, whether the station is in-service or in storage and non-operational. Therefore, it is necessary to calibrate the reference oscillator during optimization. It is recommended that the frequency measurement equipment has an accuracy 10 times greater than the accuracy required for the measurement. For example, if the frequency must be measured to within 5 pulses per minute (PPM), the accuracy of the measurement equipment should be 0.5 PPM. The reference oscillator calibration procedure depends on the station configuration. Currently, there are three possible configurations. Perform the calibration procedure that corresponds to the stations configuration: Internal reference oscillator (located on the station control board): Reference Oscillator Calibration: Internal Reference Oscillator - Manual Procedure on page 3-75, or Reference Oscillator Calibration: Internal Reference Oscillator - Auto-Net Procedure on page 3-77
External source, typically 5 MHz: Reference Oscillator Calibration: External Reference Oscillator on page 3-78 UHSO (option X873AA): Reference Oscillator Calibration: Internal Ultra High Stability Oscillator (UHSO) on page 3-78
Reference Oscillator Calibration: Internal Reference Oscillator - Manual Procedure

1.
Set up the station and R2001 analyzer with an external frequency standard to measure the stations transmitter frequency. Disconnect the stations receive antenna cable. Launch the RSS program as outlined in Launching the RSS Program on page 2-12.
2. 3.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
3-75
4.
Read the stations codeplug as outlined in Reading the Device Codeplug on page 2-14. You are now connected to the station. Click the + sign next to Service to expand the Service menu. Click Alignment Screen in the navigation pane.
5. 6.
7.
NOTE
3-76
688 1085E 35-AN
0 6/30 /201 1
Generally, the Reference Oscillator screen appears as the default screen as shown above.
8.
Observe the frequency reading on the R2001 analyzer as you click Keyup to key the station transmitter. If the observed transmit frequency reading is not the same as that specified by the FCC for that station, adjust the internal reference oscillator using the right or left arrows on either side of the Reference Oscillator Frequency graph until you obtain a reading on the analyzer as close as possible to the FCC-specified transmit frequency for that station. If the observed reading equals that specified by the FCC for that station, no changes are required.
9. 10.
Click Dekey to dekey the station. If you adjusted the reference oscillator frequency, click Save to save the reference oscillator value. Otherwise, this procedure is complete. Disconnect the test equipment.
Reference Oscillator Calibration: Internal Reference Oscillator - Auto-Net Procedure

1.
Connect the output of a stable 5 MHz or 10 MHz reference source to the BNC connector located at the bottom of the station control module front panel. Set the frequency source for 1.0 0.5V RMS output. Click either Auto-Net 5 MHz or Auto-Net 10 MHz, depending on the reference in use, to begin the calibration process using the test reference source. The status area of the screen displays the progress.
2. 3.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
3-77
4.
When the process is complete, close the Completed Successfully message window. The oscillator adjustment data is saved to the station codeplug and the station dekeys.
Reference Oscillator Calibration: External Reference Oscillator

This procedure is required only if the station transmitter and/or receiver do not lock, as indicated by the Tx Lock LED off or the Rx Fail LED lit when the external source is present and on. The accuracy of this procedure depends on the accuracy of the external source. Ensure that the 5 or 10 MHz source provides the required accuracy, as defined in Table 1 in the Routine Maintenance section of the relevant functional manual for the station.
1.
Connect the output of the stable 5 or 10 MHz external reference source to either the BNC connector located at the bottom of the station control module front panel or the BNC connector located on the station backplane. Click either Auto-Net 5 MHz or Auto-Net 10 MHz, depending on the reference in use, to begin the calibration process using the test reference source. The status area of the screen displays the progress.
2.
3.
When the process is complete, close the Completed Successfully message window. The oscillator adjustment data is saved to the station codeplug and the station dekeys.
Reference Oscillator Calibration: Internal Ultra High Stability Oscillator (UHSO)

This procedure is required only if the station transmitter and/or receiver do not lock, as indicated by the Tx Lock LED being off or the Rx Fail LED lit when the UHSO source is present and on. The accuracy of this procedure depends on the accuracy of the external source. Ensure that the 5 or 10 MHz source provides the required accuracy, as defined in Table 1 in the Routine Maintenance section of the relevant functional manual for the station.
1.
Set up the station and R2001 analyzer with an external frequency standard to measure the stations transmitter frequency. Turn the station on and allow it to warm up for about 60 minutes. Launch the RSS program as outlined in Launching the RSS Program on page 2-12. Read the stations codeplug as outlined in Reading the Device Codeplug on page 2-14. You are now connected to the station.
2. 3. 4.
3-78
688 1085E 35-AN
0 6/30 /201 1
5. 6.
Click the + sign next to Service to expand the Service menu. Click Alignment Screen in the navigation pane.
7.
NOTE
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
3-79
8.
If the station transmitter and/or receiver do not lock, as indicated by the Tx Lock LED being off or the Rx Fail LED lit when the UHSO source is present and on, click Manual Net. Otherwise proceed to step 12.
The following screen appears.
3-80
688 1085E 35-AN
0 6/30 /201 1
9.
Connect the output of the stable 5 or 10 MHz external reference source to either the BNC connector located at the bottom of the station control module front panel, or to the BNC connector located on the station backplane. Click either Auto-Net 5 MHz or Auto-Net 10 MHz, depending on the reference in use, to begin the calibration process using the test reference source. The status area of the screen displays the progress.
10.
11.
When the process is complete, close the Completed Successfully message window. The oscillator adjustment data is saved to the station codeplug and the station dekeys. If the internal reference oscillator has been calibrated, proceed to the next step. Click Keyup to key the station. While observing the R2001 analyzer display, adjust the stations reference oscillator using the left or right arrows until the R2001 displays the specified FCC transmit frequency. Click Save to save the setting in the station. Click Dekey to dekey the station.
12. 13.
14. 15.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
3-81
Setting ASTRO Tx Align and Test Procedure

NOTE
This procedure applies only to conventional and 6809 trunking stations. In an ASTRO simulcast system, all station transmitters are synchronized to a 1 pulse per second (pps) signal from a global positioning satellite (GPS) receiver. The 1 pps signal provides a common time reference for each of the transmitters. The ASTRO signaling information arriving at the station transmitter includes timestamps that specify the launch time for the voice and data transmissions. In any simulcast system, small zones of poor subscriber reception (nulls) may occur in the overlapping coverage areas from multiple transmitters. Fine adjustment of the launch time from one specific transmitter site or a combination of sites can be used to fill in these null zones. Fine launch time adjustments can also be used to compensate for GPS 1 pps propagation variations (due to factors such as cable lengths). Because the launch timestamps permit only 20 s resolution, the ASTRO Alignment and Test alignment screen is provided to allow you to specify a value with 0.1 s resolution that is added to the arriving timestamp value to provide an adjusted launch time. The specified ASTRO simulcast launch time offset value applies only to ASTRO simulcast systems and is considered optional. The factory default offset value is 0 (zero), causing no adjustment to the launch time specified by the arriving timestamp value.
1. 2.
Launch the RSS program as outlined in Launching the RSS Program on page 2-12. Read the stations codeplug as outlined in Reading the Device Codeplug on page 2-14. You are now connected to the station. Click the + sign next to Service to expand the Service menu. Click Alignment Screen in the navigation pane.
3. 4.
3-82
688 1085E 35-AN
0 6/30 /201 1
5.
NOTE
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
3-83
6.
Click the ASTRO Simulcast Test Patterns tab. The ASTRO Simulcast Test Patterns screen appears.
3-84
688 1085E 35-AN
0 6/30 /201 1
7.
Enter the desired offset value (0.1 s resolution) in the Desired ASTRO Launch Time Offset (s) field. The current value is shown in the Current ASTRO Launch Time Offset (s) field. Click Save Offset. Click Reset Station to activate the new offset value.
8. 9.
NOTE
Within a particular ASTRO simulcast system, in order to operate stations running release R10.05.00 (or later) with stations running release R10.04.00 (or later), you must add 208 s to the offset value entered in step 7 in each station running release R10.05.00 (or later). This compensates for an internal 208 s transmit delay in earlier stations and allows newer and older stations to operate within the same ASTRO simulcast system.
Generating ASTRO Test Patterns

The station is capable of generating any of the following four test patterns: Standard transmitter symbol rate (STD DEV) Standard transmitter low deviation (LOW DEV) V.52 Deviation Standard transmitter C4FM modulation (C4FM)
By causing the station to generate these tones and then viewing them on an R2670 analyzer, you may verify that the station is compliant with ASTRO Project 25 signaling specifications.
1.
Connect the station and R2670 analyzer as shown in the following figure.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
3-85
TO RECEIVE ANTENNA
TO TRANSMIT ANTENNA
STATION TRANSMIT OUTPUT STATION RECEIVE INPUT
Disconnect cable from transmit antenna to upper N-type connector on bracket.
R2670 COMMUNICATIONS ANALYZER
STATION TRANSMIT INPUT
Connect N-to-N cable between station transmit input and RF In/Out connector on R2670.
2. 3.
Launch the RSS program as outlined in Launching the RSS Program on page 2-12. Read the stations codeplug as outlined in Reading the Device Codeplug on page 2-14. You are now connected to the station. Click the + sign next to Service to expand the Service menu.
4.
3-86
688 1085E 35-AN
0 6/30 /201 1
5.
Click Test and Measurement Screen in the navigation pane. The following Test and Measurement screen appears.
6.
Click the ASTRO Test Patterns tab. The following ASTRO Test Patterns screen appears.
7. 8.
Select the desired pattern from the Select Pattern to Transmit list. Click Start Pattern Transmission to transmit the selected pattern. The screen indicates that the test pattern is now on.
9.
Observe the pattern on the R2670 display. Compare the patterns deviation with that specified in the Help file by clicking Help.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
3-87

10. 11.
If it matches the specified deviation, proceed to step 10. If it does not match the specified deviation, troubleshoot and repair.
Click Stop Pattern Transmission to stop the transmission. If required to select another pattern, proceed to step 7 and repeat steps 7 through 10. Otherwise, the procedure is complete. Disconnect the test equipment.
TDATA Calibration (6809 Trunking Station Only)

1. 2.
Launch the RSS program as outlined in Launching the RSS Program on page 2-12. Read the stations codeplug as outlined in Reading the Device Codeplug on page 2-14. You are now connected to the station. Click the + sign next to Service to expand the Service menu. Click Alignment Screen in the navigation pane.
3. 4.
5.
3-88
688 1085E 35-AN
0 6/30 /201 1
NOTE
6.
Click the TDATA Calibration tab. The TDATA Calibration screen appears.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
3-89
7.
Follow the instructions on the screen. Note that the low speed deviation (shown as 850 Hz above) is determined by the setting of the low speed deviation data field on the RF Configuration screen.
ASTRO Bit Error Rate Reports

1.
Connect the station and R2670 analyzer.
3-90
688 1085E 35-AN
0 6/30 /201 1
TO RECEIVE ANTENNA
Disconnect cable from receive antenna to lower N-type connector on bracket.
Connect N-to-N cable between station receive input and RF In/Out connector on R2670.
2.
Set the R2670 as follows: Frequency: Set to stations Rx frequency Output level: 0.5 V (-113 dBm) Modulation: V.53 or Project 25 1011 Pattern, as applicable
3. 4.
Launch the RSS program as outlined in Launching the RSS Program on page 2-12. Read the stations codeplug as outlined in Reading the Device Codeplug on page 2-14. You are now connected to the station. Click the + sign next to Service to expand the Service menu. Click Test and Measurement Screen in the navigation pane. The Test and Measurement screen appears.
5. 6.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
3-91
7. 8.
Select either V.52 or Project 25 from the Pattern Type list, as applicable. Click either Start BER Measurement or Start RSSI Measurement, as applicable. One of the following screens appear with measurement values for the following: Absolute RSSI (dBm) Relative RSSI (dB) Bit Error Rate %
3-92
688 1085E 35-AN
0 6/30 /201 1
POST-OPTIMIZATION CHECKOUT
Post-Optimization Checkout ...................................

After optimizing the equipment at a new installation, you should perform some basic tests to verify that the equipment is functioning properly within the system. Perform Station Diagnostics Diagnostics are run continuously on the station. If errors are detected, they are logged to the Status Report. Check the Status Report for errors. Frequency, Deviation, and Output Power Using standard measuring methods, verify that the station meets specifications for frequency, deviation, and output power. Place Call to Subscriber Plug a handset with Push-To-Talk (PTT) into the handset RJ-11 jack located on the front panel of the station control module. Place a call to a subscriber unit located a reasonable distance from the site. You should be able to talk and listen in simplex mode using the handset and PTT switch. This verifies all operating functions of the station that are included in the RF link, such as the receiver, power amplifier, exciter, and antenna system, and certain audio circuits in the station control module. Place Call to Console For analog only conventional stations that are connected to a remote console, establish communications using the intercom pushbutton located on the front panel of the station control board and a handset or microphone. This test verifies proper operation of the wireline circuitry, phone lines, and certain audio circuits in the station control module.
..
3-93
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
POST-OPTIMIZATION CHECKOUT
3-94
688 1085E 35-AN
0 6/30 /201 1
CHAPTER
Optimizing the ASTRO-TAC Comparator
...................................
ASTRO-TAC comparators must be optimized after they are initially installed and after maintenance actions such as retuning or replacing modules. Optimization includes tasks such as verifying the comparator hardware configuration, performing alignment, and programming the comparators codeplug. The general process for optimizing a base comparator is as follows:
1.
Connect the RSS computer to the comparator. See Connecting the PC to the Device RSS Port on page 2-11. Launch the RSS program as outlined in Launching the RSS Program on page 2-12. Read the comparators codeplug. See Reading the Device Codeplug on page 2-14. Verify that the comparators configuration data, as sent from Motorola, is as specified in the purchase order. See Verifying the Comparators Configuration Data on page 4-2. Customize the codeplug for the comparators specific installation if required. See the following as required for the specific system: Programming the IP Address on page 3-6 Programming the MAC Address on page 3-7 Setting the Devices Date and Time on page 3-8 Creating the Stations Password on page 8-2 Programming the Comparator on page 4-3
....
2. 3. 4.
5.
6.
Save the updated configuration data to a file on the RSS computer as an archive of the comparators current configuration as outlined in Saving Configuration Data to an Archive File on page 2-22. Save the updated configuration data to the comparators codeplug as outlined in Writing Codeplug Data to the Device on page 2-20.
7.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
4-1
VERIFYING THE COMPARATORS CONFIGURATION DATA
CHAPTER 4: OPTIMIZING THE ASTRO-TAC COMPARATOR
Verifying the Comparators Configuration Data ...................................

Each comparator ships from Motorolas factory with a codeplug that has been custom programmed based on information on the sales order. A portion of the comparator codeplug data includes definitions of the comparator hardware configuration, including serial number, ID, types of modules installed, and system and modulation type. It is recommended that you use the RSS to view this data to ensure that it agrees with the equipment you are currently optimizing. Also verify that the equipment configuration agrees with the vend ticket shipped with the equipment. To access the connected comparators current configuration data, perform the following procedure:
1.
Click the + sign on the Configuration node in the navigation pane to expand the Configuration branch.
2.
Click Hardware Configuration to display the comparators retrieved configuration data as shown in the example above. You can now read the comparators configuration data as programmed at the factory. Review the comparator data shown to verify that it matches the equipment and the users requirements. In most cases it matches, but there are circumstances where there may be discrepancies such as missing information on the original sales order, requiring the factory to leave certain fields at default values. Change the data as required and when done save the configuration data to either: An archive file as outlined in Saving Configuration Data to an Archive File on page 2-22, or The comparators codeplug as outlined in Writing Codeplug Data to the Device on page 2-20.
..
3.
4.
4-2
688 1085E 35-AN
0 6/30 /201 1
PROGRAMMING THE COMPARATOR
Programming the Comparator ...................................

The RSS program allows the user to set up the operating parameters for an ASTRO-TAC comparator. Figure 4-1 shows the ASTRO-TAC comparator screens provided in the navigation pane that are discussed in this section.
..
Figure 4-1 Comparator Configuration Screen Two ASTRO-TAC comparator systems are supported: The 3.6 version: This is a standard 16 port comparator. The 3.9 version: Supports both standard and expanded comparator configurations. The expanded comparator provides for a primary comparator with up to two ports for digital interface units (DIUs), and up to four expanded comparators, which support up to 64 ports for stations and receivers.
Programming the Hardware Configuration Screen

Click Hardware Configuration in the navigation pane to access the Hardware Configuration screen (Figure 4-2). See Table 4-1 for the screens data fields.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
4-3
Standard
Expanded
Figure 4-2 Hardware Configuration Screen Table 4-1 Hardware Configuration Screen Data Fields Data Field Description Range/Selections Standard
System Type Comparator Name Battery This field provides for specifying the system in which the comparator is installed. This provides for identifying the comparator. This specifies the battery type installed in the comparator. Conventional Smartzone Up to 10 alpha-numeric characters None LEAD_ACID_LIN LEAD_ACID_NON NICAD Conventional N/A N/A System dependent Customer defined Must match the battery installed in the comparator
Default
Simulcast Simulcast Launch Time Delay Vote Scan
Specifies whether the comparator is installed in a simulcast system. Specifies the delay required for transmission in a simulcast system. Used by multicast channels. Enabling allows for the addition of a preamble to all TSBK control messages in the TSBK Preamble Duration Field. Accessible only when Vote Scan is enabled.
Enabled Disabled 0 to 999 msec Enabled Disabled 0 to 999 msec
Disabled 180 Disabled
System dependent System dependent System dependent
TSBK Preamble Duration
System dependent
Expanded
Comparator Type Chassis Number This specifies the voting system that the comparator is installed in: standard or expanded. This specifies the comparators chassis number for a comparator installed in an expanded system. Standard Expanded Primary Secondary1 Secondary2 Secondary3 secondary4 Standard Primary System dependent System dependent
4-4
688 1085E 35-AN
0 6/30 /201 1
Programming the Conventional System Screen

Click Conventional System in the navigation pane to access the Conventional System screen (Figure 4-3). See Table 4-2 for the screens data fields.
Standard
Expanded
Figure 4-3 Conventional System Screen Table 4-2 Conventional System Screen Data Fields Data Field
Voice Repeat Operation Vote Priority
Description
Specifies whether voice repeat operation is used. Specifies the high priority source.
Range/Selections
Enabled Disabled Analog>Digial Digital>Analog First In 0.0 to 15.0 seconds
Default
Disabled First In

System dependent System dependent
Digital Voice Repeat Hangtime
Specifies the length of time a station connected to a comparator remains keyed-up and transmitting silence at the conclusion of a digital voice call sourced by a subscriber unit. Specifies the amount of time a station connected to a comparator remains keyed-up and transmitting silence at the conclusion of a digital voice call sourced by a console. Specifies the amount of time a station connected to a comparator remains keyed-up and transmitting silence at the conclusion of a digital data call sourced by a console (DIU port). Specifies the address that the comparator uses when there is no unique address specified in the source message that the comparator is sending to stations. Specifies which station(s) transmits hangtime generated by the comparator.
5.0 seconds
System dependent
Digital Voice Console Hangtime
0.0 to 15.0 seconds
0.0 seconds
System dependent
Digital Data Console Hangtime
0.0 to 15.0 seconds
0.0 seconds
System dependent
Default Transmitter Steering Address Hangtime HDLC Address
00 to 3F (hex)
3F (hex)
System dependent
00 to 3F (hex)
3F (hex)
System dependent
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
4-5
Table 4-2 Conventional System Screen Data Fields (continued) Data Field
Analog Voice Repeat Hangtime
Description
Specifies the amount of time a station connected to a comparator remains keyed-up and transmitting silence at the conclusion of an analog voice call sourced by a subscriber unit. Specifies the amount of time a station connected to a comparator remains keyed-up and transmitting silence at the conclusion of an analog voice call sourced by a console.
Range/Selections
0.0 to 15.0 seconds
Default
2.0 seconds

System dependent
Analog Voice Console Hangtime
0.0 to 15.0 seconds
0.0 seconds
System dependent
NOTE
When data site steering is used in conventional systems, all stations must be configured for any Site Number from 2 to 62 but not 01.
Programming the Smartzone System Screen

Click Smartzone System in the navigation pane to access the Smartzone System screen (Figure 4-4). See Table 4-3 for the screens data fields.
Figure 4-4 Smartzone System Screen Table 4-3 Smartzone System Screen Data Fields Data Field
Failsoft Enable Failsoft Mode Channel Number Vote Priority
Description
This specifies whether the comparator operates in failsoft mode. This specifies whether the comparator operates in digital or analog mode while in failsoft mode. This specifies the channel number for the comparator. This specifies the high priority source.
Range/Selections
Enabled Disabled Digital Analog None 1 through 28 Analog>Digial Digital>Analog First In
Default
Disabled Digital None First In

System dependent System dependent System dependent System dependent
4-6
688 1085E 35-AN
0 6/30 /201 1
Programming the Analog Voting Screen

Click Analog Voting in the navigation pane to access the Analog Voting screen (Figure 4-5). See Table 4-4 for the screens data fields.
Figure 4-5 Analog Voting Screen Table 4-4 Analog Voting Screen Data Fields Data Field
Analog Voting Sample Period
Description
Provides for greater accuracy in determining the noise content of a signal by increasing the interval of time over which the analog signal quality is averaged. Prevents infrastructure induced transients at the beginning of a call from degrading the initial voting decisions for each PTT. Specifies the state of the analog vote and hold feature. Ensures that the voted port does not switch for a fixed amount of time after it is selected as the voted port for the first time. Ensures that the voted port does not switch for a fixed amount of time after it is selected as the voted port. Specifies the amount of time a signal must be of higher quality than the current voted port before it is eligible to be routed as the voted port. Ensures that any transient on a port during the initial portion of an analog call is excluded from the signal quality measurement. Ensures that ports with signals of imperceptible difference in noise content are not alternatively selected as the voted port.
Range/Selections
5 to 10,000 msec
Default
50 msec

System dependent
Analog First Vote Settle Time Vote and Hold Operation First Vote Hold Time Voting Hold Time
5 to 10,000 msec
40 msec
System dependent
Enabled Disabled 5 to 10,000 msec
Disabled 250 msec
5 to 10,000 msec
250 msec
System dependent
Analog Signal Quality Debounce Time Analog Line Transient Settle Analog Voting Hysteresis
5 to 10,000 msec
150 msec
System dependent
5 to 10,000 msec
20 msec
System dependent
0 to 12.0 dB
1.1 dB
System dependent
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
4-7
Programming the Port Control Screen

Click Port Control in the navigation pane to access the Port Control screen (Figure 4-6). See Table 4-5 for the screens data fields.
Figure 4-6 Port Control Screen Table 4-5 Port Control Screen Data Fields Data Field
Port Number Port Type
Description
This specifies the comparator port currently being configured. This specifies to which device the port is connected.
Range/Selections
1 through 16 Disabled Station/Receiver DIU (conventional systems only) AEB (Smartzone systems only) Up to 10 alpha-numeric characters. Modem - 37 dBm Modem - 28 dBm V.24 Link - Internal Transmit Clock V.24 Link - External Transmit Clock Hybrid Link - Internal Transmit Clock Hybrid Link - External Transmit Clock 1
Default

Disabled
Port Alias Link Type
This identifies the alias name that is assigned to the port. This specifies what type of link connects the port and the device.
None V.24 Link Internal Transmit Clock
Customer determined System dependent
4-8
688 1085E 35-AN
0 6/30 /201 1
PERFORMING COMPARATOR ALIGNMENT
Table 4-5 Port Control Screen Data Fields Data Field

Digital Input Delay DIU Rank
Description
Specifies the amount of time required for a digital signal to travel from the stations wireline port to the comparators input wireline port. For a port connected to a DIU only: Specifies the rank among all connected DIUs that this port is given. Specifies the port number of the transmitting base stations that is closest to this ports receiver.
Range/Selections
0 to 999 msec
Default
0 msec

System dependent
0 to 15
System dependent
Data Site Steering Port
1 to 16
System dependent
Modem Fields (conventional systems only)

Input Level Differential Analog Output Level Modem Output Level Output Analog Link Timer Specifies the numerical difference between the ports modem or idle tone input signal level and the ports analog voice input signal level. Specifies the output signal level used when transmitting an analog signal. Specifies the signal level leaving the comparator on the ports 2-wire output when a modem link is either idle or supporting a digital call. Specifies how often a link is transitioned to a digital state and a message is sent to verify that the link is functional and active. -20 to +3 dB 0 dB System dependent
0 to -20 dBm -20 to +3 dBm
-14 dBm -14 dBm
10 to 300 sec
120 sec
System dependent
Hybrid V.24 Link Fields (conventional and Smartzone systems)

Input Level Differential Analog Output Level Idle Tone Output Level Specifies the numerical difference between the ports modem or idle tone input signal level and the ports analog input signal level. Specifies the output signal level used when transmitting an analog signal. Specifies the output level of the idle tone on the analog portion of the hybrid link when the analog side of the link is idle. -20 to +3 dB 0 dB System dependent
0 to -20 dBm 0 to -20 dBm
-14 dBm -10 dBm
Performing Comparator Alignment ...................................

Certain site-specific alignment tasks must be performed during optimization at the time they are installed and prior to being placed into service. The tasks required are shown below: Equalizing Batteries on page 4-10 Reference Oscillator Calibration Procedures on page 4-10
..
4-9
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
Equalizing Batteries
Sites equipped with storage batteries to provide comparator power in case of primary power failure require that the battery cells be equalized periodically. It is recommended that the batteries be equalized at the time of installation, and henceforth according to the schedule recommended by the battery manufacturer. Battery equalization is a process under which the charging voltage to the batteries is slightly boosted for a period of time, typically 48 hours to 72 hours. This slight overcharging causes the individual cells to regenerate equally and provide nearly identical output voltages.
1.
Click the Battery Equalization tab. The following Battery Equalization screen appears.
2.
Click Turn Equalization On to start the process. The comparator power supply boosts the battery charging voltage slightly for a period of time determined by the type of batteries being used, as specified in the Hardware Configuration screen. A timer in the comparator controls the length of time that the boosted charging voltage is applied and automatically sets the charging voltage to its normal level when the timer expires. If you must stop the process manually, click Turn Equalization Off.
3.
Reference Oscillator Calibration Procedures

The circuit device(s) that set the comparators reference frequency exhibit slight variations in their operating characteristics over time. Approximately 90% of these variations occur in the first year, whether the comparator is in-service or in storage and non-operational. Therefore, it is necessary to calibrate the reference oscillator during optimization.
4-10
688 1085E 35-AN
0 6/30 /201 1
It is recommended that the frequency measurement equipment have an accuracy of 10 times greater than the accuracy required for the measurement. For example, if the frequency must be measured to be within 5 PPM, the accuracy of the measurement equipment should be 0.5 PPM. The reference oscillator calibration procedure depends on the comparator configuration. There are two possible configurations. Perform the calibration procedure that corresponds to the comparators specific configuration: Internal reference oscillator (located on the comparator control board) Internal Reference Oscillator Auto-Net Procedure on page 4-11 External source, typically 5 MHz: External Reference Oscillator Calibration on page 4-11
Internal Reference Oscillator Auto-Net Procedure

1.
Connect the output of a stable 5 MHz or 10 MHz reference source to the BNC connector located at the bottom of the comparator control module front panel. Set the frequency source for 1.0 0.5 V RMS output. Click either Auto-Net 5 MHz or Auto-Net 10 MHz, depending on the reference in use, to begin the calibration process using the test reference source. The status area of the screen displays the progress.
2. 3.
4.
When the process is complete, close the Completed Successfully message window. The oscillator adjustment data is saved to the comparator codeplug and the comparator dekeys.
External Reference Oscillator Calibration

This procedure is required only if the comparator reference oscillator does not lock. The accuracy of this procedure depends on the accuracy of the external source. Ensure that the 5 MHz or 10 MHz source provides the required accuracy, as defined in Table 1 in the Routine Maintenance section of the relevant functional manual for the comparator.
1.
Connect the output of the stable 5 MHz or 10 MHz external reference source to either the BNC connector located at the bottom of the comparator control module front panel, or the BNC connector located on the comparator backplane. Click either Auto-Net 5 MHz or Auto-Net 10 MHz, depending on the reference in use, to begin the calibration process using the test reference source. The status area of the screen displays the progress.
2.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
4-11
3.
When the process is complete, close the Completed Successfully message window. The oscillator adjustment data is saved to the comparator's codeplug and a success message appears to the user.
4-12
688 1085E 35-AN
0 6/30 /201 1
CHAPTER
Diagnostics and Status
...................................
The RSS provides tools for troubleshooting and maintaining the station equipment. These include a status report log, a status panel display screen, diagnostic metering, and the ability to print a text version of the codeplug data to either a printer or a file. Status Report Log: The station reports status conditions resulting from operational or software malfunctions. Additionally, each of the diagnostics has associated with it a corresponding status. A status log, maintained in station memory, accumulates all status event data since the last station turns on. This status log may be retrieved, displayed, and used to aid in troubleshooting the station. Status Panel Display: The status panel display provides an instrument panel that displays station operating information and status messages. (The Status Panel menu also provides selections to display the current station software version). Digital Metering: The RSS allows access to critical metering points throughout the station circuitry and displays the current measurements. The readings may be compared with accepted ranges to aid in isolating a faulty module. Print Codeplug Report: A text version of the codeplug parameters and current settings may be printed to a printer connected to the RSS PC. Save Codeplug Report: A text version of the codeplug parameters and current settings may be printed to a file on the RSS PC hard disk. Remote Station Disabling/Enabling: This feature is typically used to disable (and subsequently enable) a station from a remote location through an RSS dial-up connection.
....
Station/Comparator Status Messages ...................................

Status messages may be generated by any or all of the following sources: Diagnostics run at station power-up and/or at station reset may fail and generate status messages. Diagnostics run continuously during normal station operation. Status events log provides information about: Internal abnormal operation provides information about the station itself.
..
5-1
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
STATION/COMPARATOR STATUS MESSAGES
CHAPTER 5: DIAGNOSTICS AND STATUS
External abnormal operation provides information about the system in which the station is installed.
Status messages are time stamped and stored in the station memory in a status log file. Any subsequent status messages are appended to the file, resulting in an accumulation of status data. The RSS allows the status log file to be retrieved and displayed, providing useful diagnostics information to aid in troubleshooting the station. This section describes how to access, read, and interpret the status report data.
1.
Connect the PC to the station as outlined in Connecting the PC to the Device RSS Port on page 2-11. Launch the RSS program as outlined in Launching the RSS Program on page 2-12. Read the stations codeplug as outlined in Reading the Device Codeplug on page 2-14. The Service screens provide access to the following status screens: Metering Screens, see Station Metering Screens on page 5-2 Status Report Screen, see Station/Comparator Status Report Screen on page 5-3 Status Panel Screen, see Station Status Panel Screen on page 5-26 Version Screen, see Station/Comparator Software Version on page 5-30
2. 3. 4.
Station Metering Screens

The RSS allows you to access various critical metering points throughout the station circuitry and display the current measurements or status in the Metering Screen. The readings may be compared with accepted ranges to aid in troubleshooting. The Metering menu screen allows access to critical test points for the following station modules: Station Control / Wireline Interface Module Exciter Module Power Amplifier Module (QUANTAR only) Receiver Module Power Supply Module (QUANTAR only) Internal High Stability Oscillator
When you initially click Metering Screen in the navigation pane, N/A appears for all metering values for a few seconds until the data becomes valid. N/A appears for any metering point not applicable for the station after all valid values are displayed. Click the appropriate tab to display the Metering screen for the desired module. A list of key metering points appears along with the acceptable value ranges for each metering point. See Figure 5-1 for an example.
5-2
688 1085E 35-AN
0 6/30 /201 1
Figure 5-1 Station Metering Screen Example
Station/Comparator Status Report Screen

The Status Report screen is comprised of a list of status messages, each with a date and time stamp indicating when the status message first occurred and last occurred (in relation to the last station power-up). The status list continues to grow, with previously unreported status messages added to the end of the list. The station stores up to 128 status messages in the log. Subsequent status messages overwrite the oldest status messages in the log on a first in/first out basis. If the number of messages exceed that which can be displayed, a scroll bar is provided on the right side of the screen. See Figure 5-2 and Figure 5-3 for examples. The status screens provide information that can be used during troubleshooting along with performing the troubleshooting procedures located in the equipment service manual.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
5-3
Figure 5-2 Station Status Report Screen Example
5-4
688 1085E 35-AN
0 6/30 /201 1
Figure 5-3 Comparator Status Report Screen Example
Station/Comparator-Generated Status Messages

Table 5-1 lists status messages generated within the station/comparator. Many of the station/ comparator-generated status messages do not indicate that service is required. They merely indicate that an event has occurred. These events provide the technician with status information that can be useful in debugging other issues should they arise. These status messages may be grouped into three categories: Internal System Status Messages Status messages resulting from incorrect RSS programming Hardware-Generated Status Messages
Recommendations for interpreting and responding to these status messages are provided below and in Table 5-1.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
5-5
Internal System Status Messages: These messages are reported by the station and provide a highly detailed account of the internal operation of the station. Status messages of this type are often associated with the data in internal registers, data communications between ICs on the station circuit boards, and various other software processes. These status messages may result from such occurrences as a power glitch/failure, lightning strike, or phone line malfunctions, any of which are capable of corrupting internal station data. Due to the precision of the ASTRO signaling protocol, minor errors in signaling protocol may result in status messages (even though these may not be service-affecting). Incorrect RSS Programming: Status messages in this category usually result from incorrect or invalid codeplug programming. Hardware-Generated Status Messages: Status messages of this type are the result of a station or external hardware malfunction.
Table 5-1 Station / Comparator-Generated Status Messages Source Station-Generated Status Message ABORT SEQUENC abort streaming ACCESS_DISABLE_ABORT_V52 Internal System Status p p p Exciter, Power Amp, UHSO, 5 MHz External Ref, 1PPS GPS, Battery Revert Mode, Loss of 16.8 MHz Incorrectly Programmed RSS Hardware Failure
ACCESS_TO_PRES_MEM_FAILED A_D ERROR ALREADY DISABLED ANALOG_LINK_FAIL_ACTIVE ANALOG_LINK_FAIL_INACTIVE ANT_RLY_SHORT_ALARM ASTRO_FRAME_OVERWRITE ASTRO_TEST_TONE_ABORTED BAD BD LENGTH BAD_ERROR_LOG_ENTRY BAD_EXT_WATTMETER_TYPE BAD_HC11_OPCODE BAD_INT_WATTMETER_TYPE
p p p p p Power Amplifier Antenna Relay p p p p p p p
5-6
688 1085E 35-AN
0 6/30 /201 1
Table 5-1 Station / Comparator-Generated Status Messages (continued) Source Station-Generated Status Message BAD_NVM_MCS_READ BAD_NVM_MCS_WRITE BAD_PENDULUM_COMMAND BAD_PRES_MEM_SIZE BAD_V.24_CONNECTION Base station alarm send failed BATTERY_TEMP_PROBE_ALARM BATT_REVERT_ALARM BTRY OVR ALARM buffer is empty Isr was called buffer is not last in frame but SCCE is RXF CALLSIGN_INVALID p p p p Verify Call Sign entered on Channel Information Screen p p p External Ref Not Present p p p p Check system programming p p p p p Circulator Internal System Status p p p p p p Battery Temp Probe Not Present Incorrectly Programmed RSS Hardware Failure
Cannot allocate buffer CANNOT_GET_APP CANNOT_GET_BOOT2 CANNOT_LOCK_EXT_REF CD_LOST_TIMER_EXPIRED CD_LOST_WITH_ANA_START CD_LOST_WITHOUT_ANA_START CIRC_TEMP_ALARM CIRCULAR_QUEUE_CLUSTERS CONSOLE REQUEST INDV ID <xxxx> SAME AS RADIO ID COULD_NOT_OPEN_FILE CP_TIMEOUT CP_TO_OLD_FOR_17_TRCS CRC ERRO
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
5-7
Table 5-1 Station / Comparator-Generated Status Messages (continued) Source Station-Generated Status Message CRC_LINK_DEGRADATION CROSSLOAD_CODEPLUG_ERROR CTS_ASSERTED CTS or CD were lost on loopback CTS_REMOVED CU one minute update CURR ACK SEMA V FAILED CURRENT ACK SEMAP4 CREATE FAILED CURRENTLY ACK P FAILED CURRENTLY ACK V FAILED DAMQ_FLUSH Data block timeout DATA_READY_ALREADY DATA_READY_TIMED_OUT DATA_UNDERRUN dbs_bs_abort_tx failed dbs_bs_change_busy failed dbs_bs_config failed dbs_bs_console_read () failed dbs_bs_console_write () failed dbs_bs_read_eeprom () failed dbs_bs_send_mid failed dbs_bs_set_st_id failed dbs_bs_write_eeprom () failed DBS_NVM_PTTN_ERROR Debug Queue create failed Debug Task creation failed Debug Task start failed Default in switch p p p p Internal System Status p p p p p p p p p p p p p p p p p p p p p p p p Station Control Incorrectly Programmed RSS Hardware Failure
5-8
688 1085E 35-AN
0 6/30 /201 1
Table 5-1 Station / Comparator-Generated Status Messages (continued) Source Station-Generated Status Message DETECTED_MODEM_RESET DETERMINE_STATION_MODE DIAG_TEST_RESULT_MISMATCH DIU_ACK_MSG_NOT_MATCH DIU_NACK_MSG_NOT_MATCH DIU_3_NOACKS DL CMD QUEUE CREATE FAILED DLM_OPERATING_PROPERLY DOB_TIMEOUT DPL_INACTIVE_WHEN_PL_ACTV DPLL ERROR DRIVER_OVERDRIVE_ALARM DSP_TIMEOUT DSTN_FILE_WRITE_ERROR E_A_D_RETURN E_BAD_NVM_WC_WRITE E_BAD_OPCODE E_CREATE_STREAM_SOCKET EEPROM_CHKSUM_ALARM E_ERASE_FLASH E_FRAME_INDEX_OUT_OF_SYNC E_ILLEGAL_PORT_NUMBER END QSEND FAILED ENTERING_FLASH_MODE ENTERING_NORMAL_ _MODE E_PARAMETER_RANGE E_PEND_OUT_OF_BOUNDS_ADJ ERASE_FLASH_REQ E_RECEIVE_SOCKET_DATA p p p p p p p p p p p p Exciter p p p Station Control Internal System Status p p p p p p p p p p p Exciter Power Amplifier Incorrectly Programmed RSS Hardware Failure
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
5-9
Table 5-1 Station / Comparator-Generated Status Messages (continued) Source Station-Generated Status Message ERROR_IN_COPY_FILE ERROR_IN_PERFORM_DECOMP ERROR_IN_PROC_APP_HEADER Error out of range E_STN_NOT_ACCESS_DISABLED E_SWITCH_SCS_RESET_REQ E_TIME_DATE_SET E_UHSO_OUT_OF_BOUNDS_ADJ event received no message in Queue E_WC_SCAN_CMD_TYPE EXCEPTION EXCITER ALARM EXCITER_SPIF_TIMEOUT EXT_CIRC_TEMP_ALARM (High Power QUANTAR Only) EXT_WM_FWD_PWR_ALARM (Quantro Only) EXT_WM_REFL_PWR_ALARM (Quantro Only) EXT_WM_VSWR_ALARM (Quantro Only) FAILSOFT FAN_FAILURE_ALARM FINISH_NVM_CONDITIONING First block in the middle of another frame FORCE_MODEM_HARD_RESET FORCE_MODEM_LONG_TRAIN FORCE_MODEM_SOFT_RESET Frame abort received frame_abort sending failed p p p p p p p p p Extrnl. Circ. Exciter Power Amplifier Exciter Power Amplifier Exciter Power Amplifier Trunking Failure Cooling Fan(s) Internal System Status p p p p p p p p p p Station Control Exciter Power Amplifier Incorrectly Programmed RSS Hardware Failure
5-10
688 1085E 35-AN
0 6/30 /201 1
Table 5-1 Station / Comparator-Generated Status Messages (continued) Source Station-Generated Status Message FRAME_LENGTH VIOLATION FRAMES_RCVD_DURING_IDLE FREQUENT_RESET FRMR ARRIVED WITH: FWD PWR ALARM GENERIC_ALARM_1 thru 5 GET_CP_TIMESTAMP GCU start task failed GCU task create failed gmm task creation failed gmm task start failed GSM start task failed GSM task create failed HC11_BAD_LENGTH HC11_COMM_OK HC11_MSG_RETRIES_FAILED HC11_NOSPIF HC11_NO_RESP HC11_PORT_ACCESS_FAILURE hcl task create failed hcl task start failed hct task create failed hct task start failed HDLC FRAME ABORTED on Receive HDLC_FRAMES_QUEUE_CREATE_FAILED hdlc in partn creation failed hdlc out partn creation failed HDLC PENDING QUEUE CREATE FAILED HDLC_TASK_UNINITIALIZED Internal System Status p p p p p p p p p p p p p p p p p p p p p p p p p p p p p Check status log for cause of reset Incorrectly Programmed RSS Hardware Failure
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
5-11
Table 5-1 Station / Comparator-Generated Status Messages (continued) Source Station-Generated Status Message HDLC TX QUEUE CREATE FAILED HDLC_TX_OVERRUN_ERROR HDLC WINDOW_FULL hcl task create failed hcl task start failed HDL WAKEAFTER_FAILED hdr task create failed hdr task start failed hdt task create failed hdt task start failed HIGH_POWER_RAIL Internal System Status p p p p p p p p p p Power Supply Exciter Power Amplifier Power Amplifier Power Amplifier Exciter Power Amplifier p p p p p p p p p p p p Upgrade and download latest version codeplug Incorrectly Programmed RSS Hardware Failure
HIGH_FINAL_PA_VSWR_ALARM HIGH_PA_TEMP_ALARM HIGH_TX_FINAL_VSWR_ALARM HOLD QUEUE CREATE FAILED HOST_TO_TX_CHKSUM_ERR hpl task create failed hpl task start failed hpt task create failed hpt task start failed HPT_TASK_UNINITIALIZED Idles Illegal Option I Frame should not arrive so far... ILLEGAL_RX_SPACING ILLEGAL_TX_EEPROM_ADDRESS INCOMPAT_CODEPLUG
5-12
688 1085E 35-AN
0 6/30 /201 1
Table 5-1 Station / Comparator-Generated Status Messages (continued) Source Station-Generated Status Message INDV ID <xxxx> GRP <xxxx>: EMERGENCY RQST DOWNGRADE INDV ID <xxxx> GRP <xxxx> FROM CNSL: MULTIGRP RQST ON TALKGRP INDV ID <xxxx> GRP <xxxx> FROM CNSL: NOT EMERGENCY CAPABLE INDV ID <xxxx> GRP <xxxx> FROM CNSL: TALKGRP RQST ON MULTIGRP INDV ID <xxxx> GRP <xxxx> FROM RADIO: MULTIGRP RQST ON TALKGRP INDV ID <xxxx> GRP <xxxx> FROM RADIO: TALKGRP RQST ON MULTIGRP INDV ID <xxxx> GRP <xxxx> FROM WRLN: MULTIGRP RQST ON TALKGRP INDV ID <xxxx> GRP <xxxx> FROM WRLN: TALKGRP RQST ON MULTIGRP INDV ID <xxxx> GRP ID <xxxx>: INVALID GRP RECEIVED FROM CNSL INDV ID <xxxx> GRP ID <xxxx>: INVALID GRP RECEIVED FROM RADIO INDV ID <xxxx> MULTIGRP <xxxx>: TLKGRPMULTIGRP MISMATCH INDV ID <xxxx>: SAC RECORD NOT AVAILABLE INIT_ACCESS_CTRL_PORTS INIT_FROM_BAD_LM_SW_STATE INIT_FROM_BAD_RR_SW_STATE INIT_FROM_LOSS_OF_CD INIT_FROM_MAX_INBND_TIMER INIT_FROM_MODEM_DIAG_FAIL INIT_FROM_RESET INIT_FROM_RR_ACT_TIMER INIT_FROM_TOO_MANY_SABMS INIT_FROM_USER_ENABLE p p p p p p p p p p Internal System Status Incorrectly Programmed RSS Misprogrammed subscriber radio Misprogrammed subscriber radio Misprogrammed subscriber radio Misprogrammed subscriber radio Misprogrammed subscriber radio Misprogrammed subscriber radio Misprogrammed subscriber radio Misprogrammed subscriber radio Misprogrammed subscriber radio Misprogrammed subscriber radio Misprogrammed subscriber radio Check system programming Hardware Failure
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
5-13
Table 5-1 Station / Comparator-Generated Status Messages (continued) Source Station-Generated Status Message INIT_FROM_V24_CD_LOSS INIT_FROM_V52_FAILURE INIT_FROM_XID_MGMT INITIALIZATION_FAILURE INITIALIZE_FLED INITIALIZE_FP INITIALIZE_GPS INITIAL_SEARCH_GPS_FAILURE INITIAL_SYNC_1PPS_FAILURE INIT_ISV_CROSSLOAD_CLIENT INIT_SCST INT_WM_FWD_PWR_ALARM p p Re-align power out Wireline Exciter Power Amplifier Wireline Exciter Power Amplifier Exciter Power Amplifier Internal System Status p p p p p p p No 1 pps GPS input to station No 1 pps GPS input to station Incorrectly Programmed RSS Hardware Failure
INT_WM_REFL_PWR_ALARM
Re-align power out
INT_WM_VSWR_ALARM INVALID_CMD_IN_FILE INVALID_CODEPLUG INVALID_COMMAND_MESSAGE INVALID_CPLUG_CHECKSUM INVALID DUAL WORD ISW INVALID_FREQ_BAND p p p p p p
Re-align power out
Upgrade and download latest version codeplug
Verify frequency entered on Hardware Configuration Screen
Invalid GIB opcode INVALID GROUP ID <xxx> RECEIVED FROM MANAGER
p Misprogrammed system or subscriber radio
5-14
688 1085E 35-AN
0 6/30 /201 1
Table 5-1 Station / Comparator-Generated Status Messages (continued) Source Station-Generated Status Message INVALID INDV ID <xxx> RECEIVED FROM CONSOLE Internal System Status Incorrectly Programmed RSS Misprogrammed system or subscriber radio Misprogrammed system or subscriber radio Misprogrammed system or subscriber radio p p p p p p p p p Out of Date RSS Wireline p p p p p p p p p p p p Hardware Failure
INVALID INDV ID <xxx> RECEIVED FROM MANAGER INVALID INDV ID <xxx> RECEIVED FROM RADIO
INVALID_LAUNCH_TIME INVALID_MCS_TABLE_ENTRY INVALID_METERING_VALUE INVALID_PL_DPL_DETECT INVALID_SCC INVALID SINGLE WORD ISW INVALID_SPI_MSG_LENGTH INVALID_SPI_OPCODE INVALID_TX_DATA_READY_CODE INVALID_WC_STATE INVALID_WIRELINE_BOARD ISV_CLIENT Last block arrived but frame_buf_ptr ==NULL last_buf sending failed LAUNCH_TIME_OVERRIDE LINK_FAILURE_ACTIVE LINK_FAILURE_INACTIVE LINK_HWR_INIT LINK_HWR_INIT_COMPLETE LINK_INIT_ACTIVE LINK_INIT_INACTIVE LINK MNG QUEUE CREATE FAILED LINK STILL DOWN
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
5-15
Table 5-1 Station / Comparator-Generated Status Messages (continued) Source Station-Generated Status Message LOCAL_LINK_HWR_FAILURE LOCAL_LINK_HWR_OK LOG_TX_INHIBIT_FROM_WL LOST_CD_WHILE_OP_PROP LOW_POWER_RAIL p p p Power Supply Exciter Power Amplifier Wireline ASTRO Modem p p p p p Station Control p Station Control p p Wireline ASTRO Modem Wireline ASTRO Modem p p p p p p p p Internal System Status Incorrectly Programmed RSS Hardware Failure Wireline ASTRO Modem
LT_SEND_FAILURE LT_SEND_OK malloc () failed MAX_INBND_ANA_TMR_EXP_L1 MCS_MAX_CALLS MCS_MAX_TIME MCS_NVM_PTTN_ERROR Middle block arrived but frame_buf_ptr ==NULL MI_NVM_PTTN_ERROR MISSED_ANA_STOP_ON_TX_WL Modem/Cable MODEM_COMMAND_FAILURE MODEM_FAILURE_ACTIVE MODEM_FAILURE_INACTIVE MODEM_FAST_TRAINED MODEM_LONG_TRAINED MODEM_TRAINED_ON_DATA Monitor partition create failed Monitor Queue Create failed morse_complete sending failed Morse id timedout
5-16
688 1085E 35-AN
0 6/30 /201 1
Table 5-1 Station / Comparator-Generated Status Messages (continued) Source Station-Generated Status Message MTRING_STRT_STOP_MISMATCH NACK_ERROR NEGATIVE_BLOCK_COUNT NEW_CODEPLUG_RECV NO_BUFFERS NO_CMD_FOUND Internal System Status p p p p p Corrupt RSS installation, corrupt upgrade installation p Verify Programming Exciter Power Amplifier p p p p Verify Programming p p p p p Station Control Exciter Power Amplifier Exciter Power Amplifier Exciter Power Amplifier Exciter Power Amplifier Power Amplifier Incorrectly Programmed RSS Hardware Failure
NO_LAST_TX_BUFFER NO_EXCITER_PA_MATCH NO_FORWARD_PWR Non frame on frame Queue non HH_L1_L2_CTYPE arrived NON OCTET Non-preempt mode failed NO_PA_DETECTED NO RX BD!!! OVERRUN Not RDLAP_19200 NOT_ENOUGH_MEMORY null partition id Null value variable NVM_CONDITIONING_ERROR ODR_CAL_CIRC_TEMP_ALRM ODR_CAL_PA_FAIL_ACTIVE ODR_CAL_FINL_PA_VSWR_ALRM ODR_CAL_NO_FWD_PWR_ALRM
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
5-17
Table 5-1 Station / Comparator-Generated Status Messages (continued) Source Station-Generated Status Message ODR_CAL_NOT_KEYED_2_SECS ODR_CAL_OPN_PWR_LOOP_ALRM ODR_CAL_PA_FAN_ALRM ODR_CAL_PA_LO_SUPPLY_ALRM Internal System Status Incorrectly Programmed RSS Hardware Failure Exciter Power Amplifier Exciter Power Amplifier Exciter Power Amplifier Power Supply Exciter Power Amplifier Exciter Power Amplifier Exciter Power Amplifier Exciter Power Amplifier Exciter Power Amplifier Exciter Power Amplifier Exciter Power Amplifier Exciter Power Amplifier Exciter Power Amplifier p Exciter Power Amplifier p p p p Power Supply Exciter Power Amplifier
ODR_CAL_PA_TEMP_ALRM ODR_CAL_POWER_LEVEL_ALARM ODR_CAL_TX_FINL_VSWR_ALRM ODR_CAL_TX_HOLDOFF_ACTIVE ODR_CAL_TX _INHIBIT_ACTIVE ODR_CAL_TX_LOCK_ALRM ODR_CAL_TX_LOCK_INACTIVE ODR_CAL_UNABLE_START old event detected OPEN_POWER_LOOP_ALARM Outbound MDC message arrived Outbound msg received OUT_OF_BUFFERS OVERRUN ERROR OVERVOLTAGE_ALARM
5-18
688 1085E 35-AN
0 6/30 /201 1
Table 5-1 Station / Comparator-Generated Status Messages (continued) Source Station-Generated Status Message P1_FIVE_OR_TEN_MHZ_LOST Internal System Status Incorrectly Programmed RSS Perform auto-netting procedure in Chapter 4 Hardware Failure Station Control 5 MHz External Reference Station Control Power Supply Exciter Power Amplifier Power Supply Power Amplifier p p p p p p Station Control p p p p p p p p p p p p p p p PIB Board
P1_PENDULUM_LOST PA ALARM
PA_LOW_SUPPLY_ALARM PA_ON_ALARM PEND RECEIVE FAILED PHYSICAL TX ERROR PIB ALARM PL_INACTIVE_WHEN_DPL_ACTV PORT_ACCESS_FAILURE PP_NVM_PTTN_ERROR Preempt mode failed PRIORITY_REQUEST_FAILURE PROCESS_MOVE_CMD PROC_HEADER_BYTE_ERR Psos error Psos Event After failed Psos event receive failed Psos EventSend failed Psos get buff failed Psos no event Psos PPartition create failed Psos Receive failed Psos RetBuf fail Psos Send failed Psos TaskDelete failed
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
5-19
Table 5-1 Station / Comparator-Generated Status Messages (continued) Source Station-Generated Status Message Psos TaskResume failed Psos task wake after failed Psos Timer Cancel failed PWR SPLY ALARM Internal System Status p p p p Power Supply Exciter Power Amplifier Incorrectly Programmed RSS Hardware Failure
Q_RECEIVE_TIMED_OUT QUEUE_AND_COUNT_MISMATCH Queue create failed RADIO REQUEST INDV ID <xxxx> SAME AS CONSOLE ID RAW RX QUEUE CREATE FAILED rawrxq create failed RCVD_BAD_ADDR_FRAME RCVR_FAILED RCVR_NOT_COMP READ_BYTE_COUNT_FAILURE READ_IP_HDLC_ERROR READY_TO_SIMULCAST RECEVIE_FNAME_ERR RECV_SOCKET_DATA_ERR REFL PWR ALARM REGAINED_CD_WHILE_OP_PROP REL DATA WHILE GOING DOWN remote out q creation failed remote partition create failed RE_SEARCH_GPS_FAILURE RESET RESET_DLM_STATE_VARIABLES
p p p Misprogrammed system or subscriber radio p p p Receiver Verify Programming p p p p p Receiver
p p p p No 1 pps GPS input to station p p
5-20
688 1085E 35-AN
0 6/30 /201 1
Table 5-1 Station / Comparator-Generated Status Messages (continued) Source Station-Generated Status Message RESET_FROM_ADDR_ERROR RESET_FROM_BUS_ERROR RESET_FROM_UNINIT_VECTOR Restart by MDC command RE_SYNC_1PPS_FAILURE RETRIEVED_OLD_CLST_STATIC RETRIEVED_OLD_LAUNCH_TIME RETRY_REQUIRED RF key down ridleg creation failed Rid task creation failed Rid task start failed ring creation failed Rin task creation failed Rin task start failed rmm_control queue create failed ROUTINE_INIT_FAILED routq creation failed rout task creation failed rout task start failed RSS_TEST_TONE_OVERRIDE RTS_ASSERTED RTS_REMOVED RX2_LOCK_FAIL p p p p p p p p p p p p p p p p p p Incorrectly programmed receive frequency on Channel Information Screen p p p Receiver Internal System Status p p p p No 1 pps GPS input to station Incorrectly Programmed RSS Hardware Failure
rxbdq create failed RXB_EVENT_DETECTED rx_block sending failed
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
5-21
Table 5-1 Station / Comparator-Generated Status Messages (continued) Source Station-Generated Status Message RX_LOCK_FAIL Internal System Status Incorrectly Programmed RSS Incorrectly programmed receive frequency on Channel Information Screen p p p p SAM Board SAM Board Station Control Verify RSS Programming Verify RSS Programming p p Station Control p p p p p p p p p p p p p Station Control Receiver Hardware Failure Receiver
Rx off but msg received RX_SNET_SYNC_ERROR rx_station_id sending failed SAM ALARM SAM_NOT_RESPONDING SA_NVM_PTTN_ERROR SCAN_RX_ACT_INCOMPATIBLE SCAN_ZERO_FREQS_INCOMPAT scc rx part create failed scc tx part create failed SC_NVM_PTTN_ERROR SC_REQUESTED_RETRANSMIT SCS_COMMAND SDMA_BUS_ERROR SECURENET_BUFFER_ERROR send DSP block failed SHTERM_BACK_TO_BACK SHTERM_NO_TRK_LC SHTERM_RCVD_DURING_IDLE SITE_CONTROL_ERROR SOURCE_FILE_READ_ERROR SPI_BUFFER_FULL SPI_NOSPIF SPI_TIMEOUT SR_NVM_PTTN_ERROR
5-22
688 1085E 35-AN
0 6/30 /201 1
Table 5-1 Station / Comparator-Generated Status Messages (continued) Source Station-Generated Status Message STARTED_ANALOG_RX_WL_CALL STARTED_ANALOG_TX_WL_CALL START_NVM_CONDITIONING STATION_CTRL_FAN_FAIL Internal System Status p p p Station Control cooling fan on backplane failed p p p p p p p p p p p p p p p p p p p p p p p p Incorrectly Programmed RSS Hardware Failure
STATION NOT DEKEYED STATION_PORTNAME_CLST STATION_RCVD_SABM STATION_RCVD_UA STATION_SENT_SABM STATION_SENT_UA STN_RCVD_ANALOG_START_ICW STN_RECVD_ANALOG_STOP_ICW STN_RECVD_STAND_ALONE_ICW STN_SENT_ANALOG_START_ICW STN_SENT_ANALOG_STOP_ICW STN_SENT_STAND_ALONE_ICW STOPPED_ANALOG_RX_WL_CALL STOPPED_ANALOG_TX_WL_CALL streaming still on SWITCH_DEFAULT TASK_SWARE_ERROR tca task creation failed tca task start failed TestMsg partition create failed TCH Create failed TCH Start failed Test Failed. L2 does not respond. TIME_DATE_SET
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
5-23
Table 5-1 Station / Comparator-Generated Status Messages (continued) Source Station-Generated Status Message TMON Create failed TMON Start failed TOD_LINK_DEGRADATION_OFF TOD_LINK_DEGRADATION_ON TOTAL_CD_ASSERTED TOTAL_CD_LOST TRACKING_1PPS_FAILURE Traffic timer expired Unexpectedly Traffic timer expired while GOINGUP TRUNKING_LC_OVERWRITE TSTAT_FAILURE txbdq create failed TX block failed tx_complete send failed TX_DATA_RDY_DURING_IDLE TX_EEPROM_CHECKSUM_FAILED TX_FREQ_NOT_DIV_BY_5K_6250 TX_LOCK_ALARM p p p p p p p p p Realign Exciter Verify Programming Incorrectly programmed transmit frequency on Channel Information Screen Exciter Internal System Status p p p p p p No 1 pps GPS input to station Incorrectly Programmed RSS Hardware Failure
TX_POWER_LEVEL_ALARM TX_SPI_RECEIVE_BUFF_FULL TX_SYNTH_NOT_PROGRAMMABLE p Incorrectly programmed transmit frequency on Channel Information Screen p
Exciter Power Amplifier
TX_TO_HOST_CHKSUM_ERR UHSO ALARM UHSO_COLD
5-24
688 1085E 35-AN
0 6/30 /201 1
Table 5-1 Station / Comparator-Generated Status Messages (continued) Source Station-Generated Status Message UHSO_MANUAL_OVERRIDE UHSO_WARM UNABLE_ALLOCATE_MEMORY UNABLE_TO_CALLOC_MEMORY UNABLE_TO_OPEN_FILE UNDEFINED ERRO Unexpected DBS subsystem (source/target) UNEXPECTED_ELSE Unexpected event Unexpected frame Unexpected loopback result message Unexpected message UNEXPECTED_MSG_RESP UNEXPECTED_OPCODE UNEXPECTED_TERMINATION UNEXPECTED_TIMER_MSG Uninitialized error UNKNOWN_EVNT_RECEIVED unknown host or dl_cmd Unknown idle option UNKNOWN_MODEM_TRAIN_TYPE Unknown SCCE event UNKNOWN_SIMULCAST_STATE UNKNOWN_TX_SPI_ERROR_CODE Unrecognized base station alarm UNSUPPORTED_INTERRUPT Unsupported protocol type V52_LAUNCH_TIME_ERR VARIABLE_OUT_OF_RANGE Internal System Status p p p p p p p p p p p p p p p p p p p p p p p p p p p p p Incorrectly Programmed RSS Hardware Failure
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
5-25
Table 5-1 Station / Comparator-Generated Status Messages (continued) Source Station-Generated Status Message VERSION_MISMATCH WB_PATH_ATTENUATION_MAX WB_PATH_ATTENUATION_MIN WC_NVM_PTTN_ERROR WL ALARM WL_DIG_CON_IS_DIGITAL WL_DIG_CON_IS_MODEM WL_LINK_TYPE_IS_MODEM WL_LINK_TYPE_IS_V.24 WL_REQUESTED_RETRANSMIT WL_STARTUP_ERROR WRITE_BYTE_COUNT_FAILURE WRITE_NVM_FAILURE WRITE_SOCKET_DATA_ERR WRITE_TO_PROTECTED_TX_EEP Wrong ack type Wrong MDC ack type XDATA_ERR p p p p p p p Station Control p p p p p Verify RSS Programming Wireline and/or firmware Internal System Status p p p Station Control Wireline Incorrectly Programmed RSS Hardware Failure
Station Status Panel Screen

The Station Status Panel Screen provides three screens that display station maintenance and operational status information and station software version. Function keys allow you to control various station operating characteristics through the PC keyboard. See Figure 5-4 for the Station Status Panel screen example.
5-26
688 1085E 35-AN
0 6/30 /201 1
Figure 5-4 Station Status Panel Screen Example To generate station status, click Status Panel Screen in the navigation pane. Station operating and maintenance information appears. The buttons on the screen are described in Table 5-2.
.
Table 5-2 Status Panel Screen Buttons Button Description General Buttons Next Channel Prev channel IR Channel Enable IR Channel Disable KeyUp Dekey Reset Changes station operating channel incrementally Changes station operating channel decrementally Enables repeater mode Disables repeater mode Turns on station transmitter Turns off station transmitter Performs a warm station reset (same reset as simultaneously pressing Vol Up, Vol Dn, and Intercom buttons on Station Control Module front panel). Toggles Access Disable Mode on Toggles Access Disable Mode off
Access Disable Access Enable
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
5-27
Table 5-2 Status Panel Screen Buttons (continued) Button Start Log Description Starts the logging of messages. Station Status Local Speaker Volume > Local Speaker Volume < Intercom On Intercom Off Rcvr Squelch OFF/CSQ/PL Increments speaker volume in 5 unit steps Decrements speaker volume in 5 unit steps Toggles Intercom mode on Toggles Intercom mode off Cycles through CSQ OFF, CSQ, and PL
Comparator Status Panel Screen

The comparator Status Panel Screen provides operational information about the comparators ports. See Figure 5-5 and Figure 5-6 for examples of this screen for the two comparator configurations.
Figure 5-5 Status Panel Screen Example: Primary Comparator in an Expanded Configuration
5-28
688 1085E 35-AN
0 6/30 /201 1
Figure 5-6 Status Panel Screen Example: Standard Comparator After clicking Status Panel Screen in the navigation pane, various comparator operating and maintenance information appears. The buttons on the screen are described in Table 5-3. Table 5-3 Comparator Status Panel Screen Buttons Button Description General Buttons Next Comparator Prev channel Get Link Delays Save Link Delays Help Local Control Toggle Force Vote Toggle Vote Disable Check Boxes Vote Port Force Vote Context sensitive help Changes comparator incrementally Changes comparator decrementally
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
5-29
SETTING DATE AND TIME
Station/Comparator Software Version

The Version Screen provides the currently installed software versions. See Figure 5-7.
Station
Comparator
Figure 5-7 Station and Comparator Version Screens
Setting Date and Time ...................................

In most situations, the station's internal clock is set for the current date and time for the location in which it is installed. This ensures that timestamps associated with any status messages provide correlation with the actual time of occurrence of the event. The PC Date and PC Time fields provide the current date and time of the PC's clock, and are not editable. The Device Date and Device Time fields are filled with the current date and time as read from the station. These fields are editable and can be changed to the requirements of any given installation. To change the stations date and /or time, perform the following procedure:
1.
From the Tools menu, select Set device date and time. The Set Date and Time Screen window appears.
..
5-30
688 1085E 35-AN
0 6/30 /201 1
CODEPLUG REPORTS
2. 3.
Edit the Date and/or Time fields as required for the sites location. Click OK to save the Date and Time to the device and close the window. Click Apply to save the Date and Time to the device without closing the window.
Codeplug Reports ...................................

A text version of the codeplug parameters and current settings may be: Printed to a printer connected to the PC: See Printing a Codeplug Report on page 5-31. Saved to a file on the PC hard disk: See Saving the Codeplug Report to a File on page 5-32.
..
Printing a Codeplug Report

To print the codeplug report on paper, perform the following procedure:
1.
From the File menu, select Print Codeplug Report. The Print window appears.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
5-31
CODEPLUG REPORTS
2.
If required, configure the printer connected to the RSS PC and then click Print. The RSS program formats the report and sends it to the printer.
Saving the Codeplug Report to a File

To save the codeplug report to a file, perform the following procedure:
1.
From the File menu, select Save Codeplug Report. The following browser window appears.
5-32
688 1085E 35-AN
0 6/30 /201 1
REMOTE STATION DISABLING/ENABLING
2. 3. 4.
If required, browse to the directory where you want to store the codeplug data text file. Name the file by typing the filename in the Filename field. The file is saved as a .txt file. Click Save. The RSS program formats and then saves the codeplug data text file to disk. Figure 5-8 provides an example of a saved codeplug report opened using a text editor.
Figure 5-8 Example of a Saved Codeplug Report
Remote Station Disabling/Enabling ...................................

This feature is typically used to remotely disable and subsequently enable a station through an RSS dial-up connection. When disabled, the station operates in RSS Only mode and cannot transmit, receive, or respond to console commands. The station remains in this mode, even during power cycles and resets, until an Enable command is issued.
..
5-33
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
ASTRO-TAC DIAGNOSTICS
NOTE
Disabling and enabling a station can also be performed locally through the RSS. Perform this procedure while either locally connected to the station or connected remotely through a dial-up connection.
1.
To enable or disable a connected station, from the Tools menu, select Enable/Disable Station. The Enable/Disable Station window appears.
2.
Depending on its current status (the three buttons at the bottom of the window), you can either enable or disable the station: To disable: Click Station Disable. The station resets and commences RSS Only operating mode. To enable: Click Station Enable. The station resets and commences normal operating mode.
ASTRO-TAC Diagnostics ...................................

The comparator diagnostics screen verifies that the cooling fan functions properly. The fan turns on when the comparators temperature reaches a predefined set point. To verify that the fan functions, perform the following procedure:
1.
..
Click Fan On. See the example below.
5-34
688 1085E 35-AN
0 6/30 /201 1
2.
Verify that the fan turns on. If the fan does not turn on, remove the comparator from service and contact Motorola to replace the fan. If the fan functions, click Fan Auto to return the fan to automatic operation.
3.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
5-35
5-36
688 1085E 35-AN
0 6/30 /201 1
CHAPTER
Performing Post Repair Alignment
...................................
Following replacement of certain station modules, as described in the Troubleshooting section of the appropriate station functional service manual, alignment procedures may need to be performed before placing the station back into service. The RSS program provides access to the alignment routines required by QUANTAR/Quantro station modules.
Overview of Alignment Routines ...................................

The Alignment screens (see Figure 6-1) show the available alignment routines for the QUANTAR/Quantro station products. The following is an overview of each alignment routine: Rx Wireline (Line2/Line 4): Sets the desired wireline level that results from an RF receive signal at 60% of system rated deviation. Tx Wireline: Calibrates the gain of certain audio circuits on the wireline interface board so that the desired level of audio signal from console results in a transmitted signal at 60% of rated system deviation. RSSI Calibrate: Calibrates the receiver circuitry used to derive the level of the received RF signal. Squelch Adjust: Provides the capability to set the level at which the receiver unsquelches. Battery Equalization: Maintains proper charge and capacity for storage batteries. Reference Oscillator (or UHSO): Calibrates the station reference oscillator circuit (located in the station control module) to within the required frequency tolerance. ASTRO Alignment and Test: Provides the capability to set the amount of delay (unique to each site) before transmission for station in an ASTRO simulcast system. ASTRO Pattern Generator: Allows the station to generate one of four ASTRO Project 25 test patterns for display and analysis on an R2670 analyzer. TDATA Calibration: Calibrates deviation for low speed data signal from 6809 central controller. Power Output: Calibrates the output power at the PA rated level. On Quantro stations, it calibrates the wattmeter, if installed.
.... ..
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
6-1
OVERVIEW OF ALIGNMENT ROUTINES
CHAPTER 6: PERFORMING POST REPAIR ALIGNMENT
Tx Deviation Gain Adjust: Calibrates deviation-limiting hardware and software for transmit linearity over entire Tx frequency range. Reference Modulation Compensation: Calibrates for low-frequency transmit deviation linearity for DPL and data (including ASTRO) signals.
Figure 6-1 Reference Oscillator Alignment Screen This chapter provides procedures for those alignment procedures not described elsewhere in this guide or the station functional manual. Table 6-1 lists each alignment routine and where to find the corresponding procedure. Note that some alignment routines must be performed as part of routine maintenance and/or at the time of equipment installation, as indicated in parentheses on the alignment screen. Table 6-1 Alignment Procedures Alignment Routine Rx Wireline (Line 2/Line 4) Tx Wireline RSSI Calibrate When Required Station control module Wireline interface module Station control module Receiver module Station control module Location Procedure A: Rx Wireline Alignment Procedure on page 3-57 Procedure E: Aligning TX Wireline Procedure on page 3-66 Aligning Radio Signal Strength Indicator (RSSI) on page 3-68
6-2
688 1085E 35-AN
0 6/30 /201 1
OVERVIEW OF ALIGNMENT ROUTINES
Table 6-1 Alignment Procedures (continued) Alignment Routine Squelch Adjust Battery Equalization Reference Oscillator (or UHSO) ASTRO Alignment and Test ASTRO Pattern Generator TDATA Calibration Power Output When Required Receiver module Station control module Routine maintenance only Station control module Station control module Station control module Station control module Power amplifier module Station control module Exciter module Station control module Exciter module Station control module Location Aligning Squelch Adjust Procedure on page 3-71 Equalizing Batteries on page 3-73 Calibrating Reference Oscillator Procedure on page 3-75 Setting ASTRO Tx Align and Test Procedure on page 3-82 Generating ASTRO Test Patterns on page 3-85 TDATA Calibration (6809 Trunking Station Only) on page 3-88 Aligning Power Output Procedure on page 6-4 or Aligning Power Output Procedure for a Quantro 350W VHF Station on page 6-7 Aligning Tx Deviation Gain Adjust Procedure, 350W VHF Stations on page 6-11 Aligning Reference Modulation Compensation Procedure on page 6-14
Tx Deviation Gain Adjust Reference Modulation Compensation
IMPORTANT
Before performing any of the station alignment procedures, you must dekey the station transmitter. Click Access Disable from any alignment screen to access disable the station. When finished with alignment, click Access Enable to deactivate access disable and restore the station to normal operation.
IMPORTANT
When entering data in any of the alignment screens' fields, you must click Save to accept the entry and save the changed value to the station. If you alter a parameter value and exit the particular alignment screen without saving the changed value, the station continues to operate using the changed value only until a station reset occurs (either deliberately or due to an external cause, such as a momentary power failure).
NOTE
If you experiment with a parameter value without intending to permanently change the value, you must remember not to save the value and to reset the station to restore the original parameter value(s).
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
6-3
TEST EQUIPMENT FOR POST-REPAIR ALIGNMENT PROCEDURES
Test Equipment for Post-Repair Alignment Procedures ...................................

Performing the alignment procedures requires using the RSS program in conjunction with the following test equipment: Motorola R2001/R2670 communications analyzer (or equivalent) In-line wattmeter adapter (RTL4055B or equivalent) In-line wattmeter elements (ST1200 series or equivalent)
This equipment is used to inject and monitor test signals. The RSS provides the means of adjusting various alignment parameters.
Aligning Power Output Procedure ................................... ..
..
NOTE
This procedure is not for the Quantro 350W VHF station. If you are aligning a Quantro 350W station, refer Aligning Power Output Procedure for a Quantro 350W VHF Station on page 6-7. This procedure is for QUANTAR stations with and without the high power booster option because it is the power amplifier module internal to the QUANTAR station that requires alignment, not the high power booster module. To align the stations power output, perform the following procedure:
1.
Connect the station as shown in Figure 6-2.
NOTE
An R2001 communications analyzer may be used as a wattmeter.
6-4
688 1085E 35-AN
0 6/30 /201 1
ALIGNING POWER OUTPUT PROCEDURE
1. Remove N-type connector from PA output 2. Connect cable from wattmeter Note: For Quantro stations, connect wattmeter to output of low pass filter Station
Note: Keep this cable as short as possible.
In-line wattmeter adapter and element
To TX antenna or dummy load
R2001 communications analyzer
Figure 6-2 Power Output Alignment Setup

2. 3.
Set the R2001 analyzer Display to Monitor mode. Click Alignment Screens under Service in the navigation pane. The Alignment screen appears. Click the Power Output tab. The Power Output screen appears.
4.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
6-5
ALIGNING POWER OUTPUT PROCEDURE
5. 6. 7. 8.
Click KEYUP. Read the power output as displayed by the wattmeter. Enter the value displayed by the wattmeter into the Power Read on Wattmeter field. Click ADJUST. The station automatically adjusts its output power.
NOTE
The power value displayed in the Rated Power Out field is determined by the PA Power Rating selection in the Hardware Configuration screen. The value may differ from the rated station power if the station is equipped with a circulator(s). For example, a 225W station equipped with the triple circulator option results in 170W in the Desired Power Out field (and thereinafter the power amplifier is calibrated at 170W). Refer to the Help screen for a listing of output power versus PA/circulator combinations.
9.
Click KEYUP to verify that the station correctly adjusted its output power to its rated value. If the PA FAIL LED turns on during the alignment procedure, click PA INIT and proceed to step 5.
6-6
688 1085E 35-AN
0 6/30 /201 1
ALIGNING POWER OUTPUT PROCEDURE FOR A QUANTRO 350W VHF STATION

10.
If the output power displayed on the wattmeter is not at the rated level, proceed to step 6. If the output power displayed on the wattmeter is at the rated level, proceed to step 10.
Click SAVE to save the calibrated value in memory. This may take up to 12 seconds.
Aligning Power Output Procedure for a Quantro 350W VHF Station ...................................
This procedure is for Quantro 350W stations only. To align the stations power output, perform the following procedure:
1.
..
NOTE
The circulator is bypassed using a male N-to-male N bullet connector (supplied with the station) and requires the dummy load.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
6-7
Bypass Circulator with Bullet Connector Here

MALE N -to-MALE N CONNECTOR
CIRCULATOR TRANSMIT RF FROM POWER AMPLIFIER MODULE LOW PASS FILTER
RF OUTPUT TO TRANSMIT ANTENNA
Disconnect Here
50 OHM LOAD T
Disconnect Here
THERMISTOR 50K @ 25C MATES WITH CONNECTOR ON PA POWER/TEMP SENSE CABLE
HEAT SINK
DUMMY LOAD
IN-LINE WATTMETER
Figure 6-3 Power Output Alignment Setup for Quantro 350W Stations
2.
Click Hardware Configuration in the navigation pane. The Hardware Configuration screen appears.
6-8
688 1085E 35-AN
0 6/30 /201 1
3. 4.
Select 350 Watts with No circulator in the PA Power Rating drop down list. Click Channel Information in the navigation pane, then click the Advanced tab. The Advanced Channel Information screen appears.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
6-9
5.
Set the Tx Power Out value to the desired station output power plus 40W. For example, if the desired output power is 250W then you enter 290W in the Tx Power Out field. This compensates for the fact that the output power alignment measurement point is changed from after the circulator to before the circulator.
NOTE
Although you can enter 350W in the Tx Power Out field, the maximum output power, after the circulator, is limited to 310W.
6.
Click Alignment Screens under Service in the navigation pane. The Alignment screen appears. Click the Power Output tab. The Power Output screen appears.
7.
8. 9. 10. 11. 12.
Click KEYUP. Read the power output as displayed by the wattmeter. Enter the value displayed by the wattmeter into the Power Read on Wattmeter field. Click ADJUST. The station automatically adjusts its output power. Click KEYUP to verify that the station correctly adjusted its output power to its rated value. If the PA FAIL LED turns on during the alignment procedure, click PA INIT and proceed to step 8. If the output power displayed on the wattmeter is not at the rated level, proceed to step 9.
6-10
688 1085E 35-AN
0 6/30 /201 1
ALIGNING TX DEVIATION GAIN ADJUST PROCEDURE, 350W VHF STATIONS
13.
If the output power displayed on the wattmeter is at the rated level, proceed to step 13.
Click SAVE to save the calibrated value in memory. This may take up to 12 seconds.
Aligning Tx Deviation Gain Adjust Procedure, 350W VHF Stations ...................................

To set the stations Tx Deviation Gain Adjust, perform the following procedure:
1. 2.
..
Connect the station as shown in Figure 6-4. Set the R2670 communications analyzer as follows: Display: Set to Read Deviation Narrow Bandwidth- NB Filter: Enabled High Pass Filter: 5 Hz Low Pass Filter: 20 kHz R2670 Firmware Version: Must be 5.04.xx or later 6-11
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
Figure 6-4 Tx Deviation Gain Adjust Alignment Setup

3.
Click Alignment in the navigation pane, then the Tx Deviation tab. The Tx Deviation screen appears.
6-12
688 1085E 35-AN
0 6/30 /201 1
4.
Click Key On Freq1.
NOTE
To avoid overloading the R2670 RF input, the station automatically limits its power output to either one half power or approximately 100W, whichever is lower when this alignment is performed.
5. 6.
Set the R2670 analyzer to the value displayed in the Current Frequency Is field. Read the deviation on the analyzer display (shown as two numbers; one for + and one for -). Enter the larger number into the Deviation (kHz) field for the first frequency. Click DEKEY. Repeat steps 4 through 7 for Freq2, Freq3, and Freq4. When done, click SAVE to save the values.
7. 8.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
6-13
ALIGNING REFERENCE MODULATION COMPENSATION PROCEDURE
Aligning Reference Modulation Compensation Procedure ...................................

To set the Reference Modulation Compensation, perform the following procedure:
1.
..
Figure 6-5 Reference Modulation Compensation Alignment Setup

2.
Set the R2001 communications analyzer as follows: Frequency: Tx frequency of station Display: Set to read modulation Bandwidth: Narrow Click Alignment in the navigation pane then the Reference Modulation Compensation tab. The following Reference Modulation Compensation screen appears.
3.
6-14
688 1085E 35-AN
0 6/30 /201 1
4.
Click ALIGN REF MOD1.
NOTE
To avoid overloading the analyzers RF input, the station automatically limits its power output to either one half power or approximately 100 W, whichever is lower when this alignment is performed.
5.
Set the analyzer to the transmit frequency displayed in the Current Frequency: field. The analyzer should display a square wave at approximately 10 Hz as shown in Figure 6-6. The horizontal segments of the waveform should be as straight as possible, with no noticeable droops or bumps.
NOTE
Adjust the oscilloscope to be able to adequately view the waveform during alignment.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
6-15
HORIZONTAL SEGMENTS MAY BE SLANTED BUT MUST BE STRAIGHT WITH NO DROOP OR HUMP.
HORIZONTAL SEGMENTS MUST NOT BE DROOP OR HUMP.
CORRECT WAVEFORM
INCORRECT WAVEFORM
Figure 6-6 Waveform Examples

6. 7.
If the waveform is acceptable, click SAVE and proceed to step 7. If the waveform is not acceptable, click either the right or left arrows to adjust the stations output until the waveform is acceptable. Click SAVE and proceed to step 5.
Click DEKEY. Perform steps 5 through 7 for ALIGN REF MOD2.
6-16
688 1085E 35-AN
0 6/30 /201 1
CHAPTER
Version Compatibility and Upgrades
...................................
Periodically, Motorola may release an upgraded version of the RSS program with a companion release of station firmware. Each upgraded version typically provides support for new station features. The following information provides details on RSS compatibility and the relationship between the RSS program, station firmware, and station hardware. Associated with each RSS version, are corresponding station firmware versions. QUANTAR firmware releases prior to R9.00 consisted of a four IC EPROM set for the station control board, a two EPROM set for the wireline board and one EPROM for the exciter. QUANTAR release R9.00 and later releases utilized a Flash download to a single SIMM on the station control board which also contains the wireline firmware version. The exciter board continues to use a single EPROM.
Prior to Release R07.02.02 ...................................

The release numbering format for all RSS releases prior to R07.02.02 is RX.XX with each major release resulting in an incremented release number, such as R1.00 to R2.00, and minor releases resulting in an incremented point number, such as R3.01. For the RSS, this release number is printed on the RSS CD and appears in the About window.
.... ..
NOTE
The release numbering scheme was not implemented in the initial release of the RSS and station firmware. The initial RSS release was numbered R01.19.17. This version is considered release R1.00.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
7-1
BEGINNING WITH RELEASE R7.02.02
CHAPTER 7: VERSION COMPATIBILITY AND UPGRADES
Beginning with Release R7.02.02 ...................................

The release numbering format for all RSS releases beginning with R7.02.02 is RXX.XX.XX, with each major release resulting in an incremented release number such as R08.00.00 to R09.00.00, minor releases resulting in the middle two digits being incremented, such as R09.01.00, and maintenance releases resulting in the last two digits being incremented, such as R09.01.01. For this RSS, the release number is printed on the RSS CD and appears in the About window.
..
NOTE
When contacting Motorola for RSS technical support, be sure to provide the complete version information as displayed in the About window by clicking Version Details.
RSS Program Version and Station Firmware Relationship ...................................

Each RSS program version is accompanied with a simultaneous upgrade release of the station software. Table 7-1 through Table 7-6 describe the relationships between RSS program versions, IC part numbers and conventional, 6809 trunking, and IntelliRepeater station software versions.
..
7-2
688 1085E 35-AN
0 6/30 /201 1
RSS PROGRAM VERSION AND STATION FIRMWARE RELATIONSHIP
Table 7-1 TRN74751 and TRN76671 Station Control Boards RSS Compatibility RSS Version Release Conventional/6809 Trunking Release
SCM: U653 U654 WL: U134 U135 EXC: U3701 SCM: U653 U654 WL: U134 U135 EXC: U3701 SCM: U653 U654 WL: U134 U135 EXC: U3701 SCM: U653 U654 WL: U134 U135 EXC: U3701 SCM: U653 U654 WL: U134 U135 EXC: U3701 N/A
IntelliRepeater/SmartZone Release SZ2.0 IC/ Part No.

SCM: U653 U654 WL: U134 U135 EXC: U3701 5191022C03 5191022C04 5191013H12 5191013H11 5191012H98
IC/ Part No.

5191020C41 5191020C42 5191013H14 5191013H13 5191012L68
Firmware Version2
SCM: B011.01.009 WL: B011.01.006 EXC: B011.01.003
Firmware Version2
IR: 8.14 Comb WL: 930504 EXC: 7.11
R1.00 (called R1.00 R01.19.17) (Conventional Only)
R2.00
R2.00
5191020C47 5191020C48 5191013H18 5191013H17 5191012L71
SCM: B013.02.015 WL: B013.02.007 EXC: B013.02.004
SZ2.3
SCM: U653 U654 WL: U134 U135 EXC: U3701
5191022C05 5191022C06 5191013H18 5191013H17 5191012L71
IR: 10.26 WLB: B013.02.007 EXC: B013.02.004
R3.00
R3.00
5191020C49 5191020C50 5191013H20 5191013H19 5191012L72
SCM: B013.03.007 WL: B013.03.003 EXC: B013.03.003
SZ2.7
SCM: U653 U654 WL: U134 U135 EXC: U3701
5191022C11 5191022C12 5191013H22 5191013H21 5181012L73
IR:11.69 WL: B013.03.007 EXC: B013.03.006
R3.01
R3.01
5191020C51 5191020C52 5191013H22 5191013H21 5191012L73
SCM: B013.03.013 WL: B013.03.007 EXC: B013.03.006
R4.00
R4.01
5191022C13 5191022C14 5191013H26 5191013H25 5191012L75
SCM: B013.04.007 WL: B013.04.004 EXC: B013.04.004
R5.00
R5.01
N/A
SZ2.7E
SCM: U653 U654 WL: U134 U135 EXC: U3701
5191022C11 5191022C12 5191013H22 5191013H21 5181012L73
IR: 11.69 WL: B013.03.007 EXC: B013.03.006
Notes: 1.There is no further development for these control boards 2. The firmware versions may be displayed by selecting Status Report from the Service menu. Exciter firmware version numbers (Conventional/6809 Trunking) are not displayed for RSS Releases R1.00 through R3.01. IR and Exciter firmware version numbers (IntelliRepeater/SmartZone) are not displayed.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
7-3
Table 7-2 TTN40941 and TRN79001 Station Control Boards RSS Compatibility RSS Version Release R5.00 Conventional/6809 Trunking Release R5.00
SCM: U651 U652 U653 U654 WL: U134 U135 EXC: U3701 SCM: U651 U652 U653 U654 WL: U134 U135 EXC: U3701 SCM: U651 U652 U653 U654 WL: U134 U135 EXC: U3701 SCM: U651 U652 U653 U654 WL: U134 U135 EXC: U3701 SCM: U651 U652 U653 U654 WL: U134 U135 EXC: U3701
IntelliRepeater/SMARTZONE Release SZ2.7

SCM: U653 U654 WL: U134 U135 EXC: U3701
IC/Part No.
5191020H09 5191020H10 5191020H11 5191020H12 5191013H28 5191013H27 5191012P13
Firmware Version2
SCM: B013.05.07 WL: B013.05.001 EXC: B013.05.02
IC/ Part No.

5191022C11 5191022C12 5191013H22 5191013H21 5181012L73
Firmware Version2
IR: 11.69 WL: B013.03.007 EXC: B013.03.006
R5.01
5191020H13 5191020H14 5191020H15 5191020H16 5191013H30 5191013H29 5191012P13
SCM: B013.05.07 WL: B013.05.001 EXC: B013.05.02
SZ2.7E
SCM: U651 U652 U653 U654 WL: U134 U135 EXC: U3701
5191020H21 5191020H22 5191020H23 5191020H24 5191013H28 5191013H27 5191012P13
IR: 13.11 WL: B013.05.001 EXC: B013.05.002
R6.00
R6.00
5191020L01 5191020L02 5191020L03 5191020L04 5191013H66 5191013H65 5191013P14
SCM: 15.06.009 WL: 15.06.004 EXC: 13.05.002
SZ2.0.3
5191022C29 5191022C30 5191022C31 5191022C32 5191022H66 5191022H65 5191013P13
IR: 15.06.514 WL: 15.06.004 EXC: 13.05.002
R6.01
5191020L01 5191020L02 5191020L03 5191020L04 5191013H68 5191013H67 5191013P14
SCM: 15.06.009 WL: 15.06.011 EXC: 13.05.002
SZ2.0.3
5191022C33 5191022C34 5191022C35 5191022C36 5191013H68 5191013H67 5191013P13
IR: 16.06.521 WL: 16.06.011 EXC: 13.05.002
R6.02
5191020L05 5191020L06 5191020L07 5191020L08 5191013H70 5191013H69 5191013P14
SCM: 16.06.018 WL: 16.06.013 EXC: 13.05.002
SZ2.0.3
5191022C33 5191022C34 5191022C35 5191022C36 5191013H70 5191013H69 5191013P13
IR: 16.06.521 WL: 16.06.013 EXC: 13.05.002
7-4
688 1085E 35-AN
0 6/30 /201 1
Table 7-2 TTN40941 and TRN79001 Station Control Boards RSS Compatibility (continued) RSS Version Release R7.00 Conventional/6809 Trunking Release R7.00
SCM: U651 U652 U653 U654 WL: U134 U135 EXC: U3701 SCM: U651 U652 U653 U654 WL: U134 U135 EXC: U3701 SCM: U651 U652 U653 U654 WL: U134 U135 EXC: U3701
IntelliRepeater/SMARTZONE Release SZ2.0.3

IC/Part No.
5191020L13 5191020L14 5191020L15 5191020L16 5191013H74 5191013H73 5191012P14
Firmware Version2
SCM: 016.07.015 WL: 016.07.008 EXC: 16.06.001
IC/ Part No.

5191022C33 5191022C34 5191022C35 5191022C36 5191013H74 5191013H73 5191012P14
Firmware Version2
IR: 16.06.521 WL:16.07.008 EXC: 16.06.001
R7.01
5191020L17 5191020L18 5191020L19 5191020L20 5191013H76 5191013H75 5191012P14
SCM: 016.07.026 WL: 016.07.013 EXC: 016.06.001
SZ2.0.3
5191022C33 5191022C34 5191022C35 5191022C36 5191013H76 5191013H75 5191012P14
IR: 16.06.521 WL: 16.07.013 EXC: 16.06.001
R7.02
5191020L21 5191020L22 5191020L23 5191020L24 5191013H78 5191013H77 5191012P14
SCM: 016.07.030 WL: 016.07.014 EXC: 016.06.001
SZ2.0.3
5191022C33 5191022C34 5191022C35 5191022C36 5191013H78 5191013H77 5191012P14
IR: 16.06.521 WL: 16.07.014 EXC: 16.06.001
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
7-5
Table 7-2 TTN40941 and TRN79001 Station Control Boards RSS Compatibility (continued) RSS Version Release R07.02.02 Conventional/6809 Trunking Release R7.03
IntelliRepeater/SMARTZONE Release SZ2.0.3

SCM: U651 U652 U653 U654 WL: U134 U135 EXC: U3701 SCM: U651 U652 U653 U654 WL: U134 U135 EXC: U3701 SCM: U651 U652 U653 U654 WL: U134 U135 EXC: U3701
IC/Part No.
5191020L25 5191020L26 5191020L27 5191020L28 5191013H99 5191013H98 5191012P14
Firmware Version2
SCM: 016.07.034 WL: 016.07.018 EXC: 016.07.001
IC/ Part No.

5191022C33 5191022C34 5191022C35 5191022C36 5191013H99 5191013H98 5191012P14
Firmware Version2
IR: 16.06.521 WL: 16.07.018 EXC: 16.06.001
R8.0
SZ2.0.3
5191022C37 5191022C38 5191022C39 5191022C41 5191013H99 5191013H98 5191012P14
IR: 16.08.503 WL: 16.07.018 EXC: 16.06.001
R8.1
SCM: U651 U652 U653 U654 WL: U134 U135 EXC: U3701 SCM: U651 U652 U653 U654 WL: U134 U135 EXC: U3701 SCM: U651 U652 U653 U654 WL: U134 U135 EXC: U3701 SCM: U651 U652 U653 U654 WL: U134 U135 EXC: U3701
5191020L37 5191020L38 5191020L39 5191020L40 5191013L28 5191013L27 5191012P14
SCM: 016.08.004 WL: 016.08.002 EXC: 016.07.001
SZ2.0.3
5191022C46 5191022C47 5191022C48 5191022C49 5191013L28 5191013L27 5191012P14
IR: 16.08.508 WL: 16.08.002 EXC: 16.06.001
R8.2
5191020L88 5191020L89 5191020L90 5191020L91 5191013L28 5191013L27 5191012P14
SCM: 016.08.006 WL: 016.08.002 EXC: 016.07.001
R8.3
PC5091104000008008 PC5091204000008008 PC5091304000008008 PC5091404000008008 PC5095104000008003 PC5095204000008003 5191012P14
SCM: 016.08.008 WL: 016.08.003 EXC: 016.07.001
SZ2.0.3
SCM: U651 U652 U653 U654 WL: U134 U135 EXC: U3701 SCM: U651 U652 U653 U654 WL: U134 U135 EXC: U3701
5191022C46 5191022C47 5191022C48 5191022C49 PC5095104000008003 PC5095204000008003 5191012P14
IR: 16.08.508 WL: 16.08.003 EXC: 16.06.001
R8.5
PC5091104000008010 PC5091204000008010 PC5091304000008010 PC5091404000008010 PC5095104000008003 PC5095204000008003 5191012P14
SCM: 016.08.010 WL: 016.08.003 EXC: 016.07.001
SZ2.0.3
PC5091104000008511 PC5091204000008511 PC5091304000008511 PC5091404000008511 PC5095104000008003 PC5095204000008003 5191012P14
IR: 16.08.511 WL: 16.08.003 EXC: 16.06.001
Notes: 1. No further development for these control boards 2. The firmware versions may be displayed by selecting Status Report from the Service menu. IR and Exciter firmware version numbers (IntelliRepeater/SMARTZONE) are not displayed.
7-6
688 1085E 35-AN
0 6/30 /201 1
Table 7-3 CLN6960, CLN6961, CLN6873, and CLN7060 Station Control Boards (with Software Download Capability; Non-IntelliRepeater 5.0 Stations) RSS Compatibility RSS Version Release Release R9.00 Conventional/6809 Trunking Software/IC Part Numbers
SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: 0180706F52 PC5091103000009017 PC5091002000009012 PC5095201000009008 PC5095101000009008 PC5095103000009015 PC5093104000009001 SCM: SC_020_09_028 WL: WL_020_09_022 Boot: B2_020_09_012 EXC: 020.09.001
IntelliRepeater/SMARTZONE Release SZ3.0 Software/IC Part Numbers

SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134: U135: App Sftwr: EXC: 0180706F51 PC5091103000009519 PC5091002000009012 PC5095201000009008 PC5095101000009008 PC5095103000009015 PC5093104000009001 SCM: IR_020_09_528 WL: WL_020_09_022 Boot: B2_020_09_012 EXC: 020.09.001
Software Version1
SCM: SC_020_09_017 WL: WL_020_09_015 Boot: B2_020_09_012 EXC: 020.09.001
Software Version1
SCM: IR_020_09_519 WL: WL_020_09_015 Boot: B2_020_09_012 EXC: 020.09.001
R09.00.00
R9.01
0180706F52 PC5091103000009028 PC5091002000009012 PC5095201000009008 PC5095101000009008 PC5095103000009022 PC5093104000009001
SZ3.0
0180706F51 PC5091103000009528 PC5091002000009012 PC5095201000009008 PC5095101000009008 PC5095103000009022 PC5093104000009001
R09.02.01
R9.02
0180706F52 PC5091103000009031 PC5091002000009014 PC5095201000009008 PC5095101000009008 PC5095103000009022 PC5093104000009001
SZ2.0.32 and SZ3.0
0180706F51 PC5091103000009533 PC5091002000009014 PC5095201000009008 PC5095101000009008 PC5095103000009022 PC5093104000009001
R09.03.00
R9.03
0180706F52 PC5091103000009042 PC5091002000009016 PC5095201000009008 PC5095101000009008 PC5095101000009028 PC5093104000009001
0180706F51 PC5091103000009542 PC5091002000009016 PC5095201000009008 PC5095101000009008 PC5095101000009028 PC5093104000009001
R9.04
0180706F52 PC5091103000009044 PC5091002000009016 PC5095201000009008 PC5095101000009008 PC5095101000009028 PC5093104000009003
0180706F51 PC5091103000009544 PC5091002000009016 PC5095201000009008 PC5095101000009008 PC5095101000009028 PC5093104000009003
R9.04.03
0180706F52 PC5091103000009044 PC5091002000009021 PC5095201000009008 PC5095101000009008 PC5095101000009028 PC5093104000009003
0180706F51 PC5091103000009544 PC5091002000009021 PC5095201000009008 PC5095101000009008 PC5095101000009028 PC5093104000009003
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
7-7
Table 7-3 CLN6960, CLN6961, CLN6873, and CLN7060 Station Control Boards (with Software Download Capability; Non-IntelliRepeater 5.0 Stations) RSS Compatibility (continued) RSS Version Release Release R09.05.00 R9.05 Conventional/6809 Trunking Software/IC Part Numbers
SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: 0180706F52 PC509110300009055 PC5091002000009022 PC5095201000009008 PC5095101000009008 PC509500100009033 PC5093104000009004 SCM: SC_020_09_062 WL: WL_020_09_034 Boot: B2_020_09_025 EXC: 020.09.004
IntelliRepeater/SMARTZONE Release SZ2.0.32 and SZ3.0 Software/IC Part Numbers

SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2: WL: U134 U135 App Sftwr EXC: 0180706F51 PC509110300009552 PC5091002000009022 PC5095201000009008 PC5095101000009008 PC509500100009033 PC5093104000009004 SCM: IR_020_09_558 WL: WL_020_09_034 Boot: B2_020_09_025 EXC: 020.09.004
Software Version1
Software Version1
R09.06.00
R9.06
0180706F52 PC509110300009062 PC5091002000009025 PC5095201000009008 PC5095101000009008 PC509500100009034 PC5093104000009004
0180706F51 PC509110300009558 PC5091002000009025 PC5095201000009008 PC5095101000009008 PC509500100009034 PC5093104000009004
R09.07.00
R9.07
0180706F52 PC509F10300009068 PC5091002000009026 PC5095201000009008 PC5095101000009008 PC509500100009036 PC5093104000009005
0180706F51 PC509F10400009564 PC5091002000009026 PC5095201000009008 PC5095101000009008 PC509500100009036 PC5093104000009005
R10.00.00 R10.00
0180706F52 PC509F10300010002 PC5091002000010001 PC5095204000009813 PC5095104000009813 PC509500100010001 PC5093104000009005
0180706F51 PC509F10400010502 PC5091002000010001 PC5095204000009813 PC5095104000009813 PC509500100010001 PC5093104000009005
R10.01.00 R10.01
0180706F52 PC509F10300010013 PC5091002000010001 PC5095204000009813 PC5095104000009813 PC509500100010001 PC5093104000009005
0180706F51 PC509F10400010513 PC5091002000010001 PC5095204000009813 PC5095104000009813 PC509500100010001 PC5093104000009005
R10.02.00 R10.02
0180706F52 PC509F10300010021 PC5091002000010001 PC5095204000010806 PC5095104000010806 PC509500100010007 PC5093104000009005
0180706F51 PC509F10400010520 PC5091002000010001 PC5095204000010806 PC5095104000010806 PC509500100010007 PC5093104000009005
R10.03.00 R10.03
0180706F52 PC509F10300010030 PC5091002000010002 PC5095204000010807 PC5095104000010807 PC509500100010008 PC5093104000009005
SCM: SC_020_10_030 WL; WL_020_10_008 Boot; B2_020_10_002 EXC: 020.09.005
SZ2.0.32 and SZ3.0
SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC:
0180706F51 PC509F10400010527 PC5091002000010002 PC5095204000010807 PC5095104000010807 PC509500100010008 PC5093104000009005
R10.04.00 R10.04
0180706F52 PC509F10300010042 PC5091002000010003 PC5095204000010807 PC5095104000010807 PC509500100010008 PC5093104000009005
SZ2.0.32 and SZ3.0
0180706F51 PC509F10400010536 PC5091002000010003 PC5095204000010807 PC5095104000010807 PC509500100010008 PC5093104000009005
7-8
688 1085E 35-AN
0 6/30 /201 1
SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: 0180706F52 PC509F10300010049 PC5091002000010008 PC5095204000010812 PC5095104000010812 PC509500100010014 PC5093104000009005 SCM: SC_020_10_058 WL: WL_020_10_018 Boot: B2_020_10_012 EXC: 020.09.005
IntelliRepeater/SMARTZONE Release SZ2.0.32 and SZ3.0 Software/IC Part Numbers

SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: 0180706F51 PC509F10400010543 PC5091002000010008 PC5095204000010812 PC5095104000010812 PC509500100010014 PC5093104000009005 SCM: IR_020_10_552 WL: WL_020_10_018 Boot: B2_020_10_012 EXC: 020.09.005
Software Version1
Software Version1
R10.06.00 R10.06
0180706F52 PC509F10300010058 PC5091002000010012 PC5095204000010816 PC5095104000010816 PC509500100010018 PC5093104000009005
SZ3.0
0180706F51 PC509F10400010552 PC5091002000010012 PC5095204000010816 PC5095104000010816 PC509500100010018 PC5093104000009005
R10.07
0180706F52 PC509F10300010066 PC5091002000010016 PC5095204000010816 PC5095104000010816 PC509500100010021 PC5093104000009005
SZ3.0
0180706F51 PC509F10400010560 PC5091002000010016 PC5095204000010816 PC5095104000010816 PC509500100010021 PC5093104000009005
R10.07.00 R10.08
0180706F52 PC509F10300010066 PC5091002000010016 PC5095204000010816 PC5095104000010816 PC509500100010021 PC5093104000009005
SZ3.0
0180706F51 PC509F10400010565 PC5091002000010016 PC5095204000010816 PC5095104000010816 PC509500100010021 PC5093104000009005
R10.09
0180706F52 PC509F10300010080 PC5091002000010016 PC5095204000010816 PC5095104000010816 PC509500100010021 PC5093104000009005
SZ3.0
0180706F51 PC509F10400010578 PC5091002000010016 PC5095204000010816 PC5095104000010816 PC509500100010021 PC5093104000009005
R10.08.00 R10.10
0180706F52 PC509F10300010086 PC5091002000010019 PC5095204000010816 PC5095104000010816 PC509500100010021 PC5093104000009005
SZ3.0
0180706F51 PC509F104000010584 PC5091002000010019 PC5095204000010816 PC5095104000010816 PC509500100010021 PC5093104000009005
R10.11.00
R10.11
0180706F52 PC509F10300010095 PC5091002000010022 PC5095204000010816 PC5095104000010816 PC509500100010025 PC5093104000009005
SZ3.0
0180706F51 PC509F104000010593 PC5091002000010022 PC5095204000010816 PC5095104000010816 PC509500100010025 PC5093104000009005
R10.12.00 R10.12
0180706F52 PC509F10300010101 PC5091002000010022 PC5095204000010816 PC5095104000010816 PC509500100010025 PC5093104000009005
SZ3.0
0180706F51 PC509F104000010599 PC5091002000010022 PC5095204000010816 PC5095104000010816 PC509500100010025 PC5093104000009005
SCM: IR_020_10_599 WL: L_020_10_025 Boot: B2_020_10_022 EXC: 020.09.005
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
7-9
SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: 0180706F52 PC509F10300010101 PC5091002000010022 PC5095204000010816 PC5095104000010816 PC509500100010025 PC5093104000009005 SCM: SC_020_12_008 WL: WL_020_12_003 Boot: B2_020_10_022 EXC: 020.09.009

SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 App Sftwr EXC: 0180706F51 PC509F104000010599 PC5091002000010022 PC5095204000010816 PC5095104000010816 PC509500100010025 PC5093104000009005 SCM: IR_020_12_508 WL: WL_020_12_003 Boot: B2_020_10_022 EXC: 020.09.009
Software Version1
Software Version1
R12.01.00 R12.01
0180706F52 PC509F10300012008 PC5091002000010022 PC5095204000010816 PC5095104000010816 PC509500100012003 PC5093104000009009
SZ3.0 and SZ4.1
0180706F51 PC509F104000012508 PC5091002000010022 PC5095204000010816 PC5095104000010816 PC509500100012003 PC5093104000009009
R12.02.00 R12.02
0180706F52 PC509F10300012021 PC5091002000010022 PC5095204000010816 PC5095104000010816 PC509F02N000012004 PC509E02M000009010
SZ3.0 and SZ4.1
0180706F51 PC509F104000012508 PC509F104000010022 PC509F02N000012004 PC509E02M000009010
R12.03.00 R12.03
SZ3.0 and SZ4.1
SCM: P651 SIMM App Sftwr Boot2 App Sftwr EXC:
SCML: IR_020_12_524 WL: WL_020_12_008 Boot: B2_020_10_022 EXC: 020.09.017
R12.04.00 R12.04
SZ3.0 and SZ4.1
R12.05.00 R12.05
SZ3.0 and SZ4.1
R12.06.00 R12.06
SZ3.0 and SZ4.1
R12.07.00 R12.07
SZ3.0 and SZ4.1
7-10
688 1085E 35-AN
0 6/30 /201 1
SCM: P651 SIMM App Sftwr Boot2 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 App Sftwr EXC: 0180706F52 PC509F10300013009 PC5091002000010022 PC509F02N000012014 PC509E02M000009017
IntelliRepeater/SMARTZONE Release SZ3.0 and SZ4.1 SZ3.0 and SZ4.1 SZ3.0 and SZ4.1 SZ3.0 and SZ4.1 Software/IC Part Numbers
SCM: P651 SIMM App Sftwr Boot2 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 App Sftwr EXC: SCM: P651 SIMM App Sftwr Boot2 App Sftwr EXC: 0180706F51 PC509F104000012541 PC509F104000010022 PC509F02N000012014 PC509E02M000009017
Software Version1
Software Version1
R13.01.00 R13.01
0180706F52 PC509F10300013017 PC5091002000013001 PC509F02N000013002 PC509E02M000009017
R13.02.00 R13.02
0180706F52 PC509F10300013022 PC5091002000013001 PC509F02N000013002 PC509E02M000009017
R14.00.00 R14.00
0180706F52 PC509F103000140xx PC5091002000014001 PC509F02N000014000 PC509E02M000009017
SCM: SC_020_14_0xx WL: WL_020_14_0xx Boot: B2_020_14_001 EXC: 020.09.017
0180706F51 PC509F1040000145xx PC509F104000014001 PC509F02N000014501 PC509E02M000009017
Notes: 1. The software versions may be displayed by selecting Status Report from the Service menu, or by selecting Status Panel/ Software Version/Set Date and Time from the Service menu. 2. Stations in systems running SZ2.0.3 are not software download capable.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
7-11
Table 7-4 Factory Shipped Upgrade Kit1 RSS Compatibility (for stations without Software Download Capability) RSS Version Release Release R09.02.01 R9.02 Conventional/6809 Trunking Software/IC Part Numbers
SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 EXC SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 EXC: 0180706F47 PC5091103000009031 PC5091002000009014 PC5095204000009805 PC5095104000009805 PC5093104000009001 SCM: SC_020_09_042 WL: WL_020_09_809 Boot: B2_020_09_016 EXC: 020.09.001

SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 EXC: 0180706F50 PC5091103000009533 PC5091002000009014 PC5095204000009805 PC5095104000009805 PC5093104000009001 SCM: IR_020_09_542 WL: WL_020_09_809 Boot: B2_020_09_016 EXC: 020.09.001
Software Version (Note 1)


R09.03.00
R9.03
0180706F47 PC5091103000009042 PC5091002000009016 PC5095204000009809 PC5095104000009809 PC5093104000009001
0180706F50 PC5091103000009542 PC5091002000009016 PC5095204000009809 PC5095104000009809 PC5093104000009001
R9.04
0180706F47 PC5091103000009044 PC5091002000009016 PC5095204000009809 PC5095104000009809 PC5093104000009003
0180706F50 PC5091103000009544 PC5091002000009016 PC5095204000009809 PC5095104000009809 PC5093104000009003
R9.04.03
0180706F47 PC5091103000009044 PC5091002000009021 PC5095204000009809 PC5095104000009809 PC5093104000009003
0180706F50 PC5091103000009544 PC5091002000009021 PC5095204000009809 PC5095104000009809 PC5093104000009003
R09.05.00
R9.05
0180706F47 PC509110300009055 PC5091002000009022 PC5095204000009812 PC5095104000009812 PC5093104000009004
SZ2.032
SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 EXC:
0180706F50 PC509110300009552 PC5091002000009022 PC5095204000009812 PC5095104000009812 PC5093104000009004
R09.06.00
R9.06
0180706F47 PC509110300009062 PC5091002000009025 PC5095204000009813 PC5095104000009813 PC5093104000009004
SZ2.032
0180706F50 PC509110300009558 PC5091002000009025 PC5095204000009813 PC5095104000009813 PC5093104000009004
R09.07.00
R9.07
0180706F47 PC509F10300009068 PC5091002000009026 PC5095204000009813 PC5095104000009813 PC5093104000009005
SZ2.032
0180706F50 PC509F10400009564 PC5091002000009026 PC5095204000009813 PC5095104000009813 PC5093104000009005
R10.00.00 R10.00
0180706F47 PC509F10300010002 PC5091002000010001 PC5095204000009813 PC5095104000009813 PC5093104000009005
SZ2.032
0180706F50 PC509F10400010502 PC5091002000010001 PC5095204000009813 PC5095104000009813 PC5093104000009005
R10.01.00 R10.01
0180706F47 PC509F10300010013 PC5091002000010001 PC5095204000009813 PC5095104000009813 PC5093104000009005
SZ2.032
0180706F50 PC509F10400010513 PC5091002000010001 PC5095204000009813 PC5095104000009813 PC5093104000009005
7-12
688 1085E 35-AN
0 6/30 /201 1
Table 7-4 Factory Shipped Upgrade Kit1 RSS Compatibility (for stations without Software Download Capability) RSS Version Release Release R10.02.00 R10.02 Conventional/6809 Trunking Software/IC Part Numbers
SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 EXC: 0180706F47 PC509F10300010021 PC5091002000010001 PC5095204000010806 PC5095104000010806 PC5093104000009005 SCM: SC_020_10_030 WL: WL_020_10_807 Boot: B2_020_10_002 EXC: 020.09.005

SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 EXC: SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 EXC: SCM: P651 SIMM App Sftwr Boot2 (3)WL: U134 U135 App Sftwr EXC: 0180706F50 PC509F10400010520 PC5091002000010001 PC5095204000010806 PC5095104000010806 PC5093104000009005 SCM: IR_020_10_527 WL: WL_020_10_807 Boot: B2_020_10_002 EXC: 020.09.005


R10.03.00 R10.03
0180706F47 PC509F10300010030 PC5091002000010002 PC5095204000010807 PC5095104000010807 PC5093104000009005
SZ2.032
0180706F50 PC509F10400010527 PC5091002000010002 PC5095204000010807 PC5095104000010807 PC5093104000009005
R10.04.00 R10.04
0180706F47 PC509F10300010042 PC5091002000010003 PC5095204000010807 PC5095104000010807 PC5093104000009005
SZ2.032
0180706F50 PC509F10400010536 PC5091002000010003 PC5095204000010807 PC5095104000010807 PC5093104000009005
SCM: R_020_10_536 WL: WL_020_10_807 Boot: B2_020_10_003 EXC: 020.09.005
R10.05.00 R10.05
0180706F47 PC509F10300010049 PC5091002000010008 PC5095204000010812 PC5095104000010812 PC5093104000009005
SZ2.032
0180706F50 PC509F10400010543 PC5091002000010008 PC5095204000010812 PC5095104000010812 PC5093104000009005
R10.06.00 R10.06
0180706F47 PC509F10300010058 PC5091002000010012 PC5095204000010816 PC5095104000010816 PC5093104000009005
SZ2.032
0180706F50 PC509F10400010552 PC5091002000010012 PC5095204000010816 PC5095104000010816 PC5093104000009005
R14.00.00 R14.00
SZ2.0.3
0180706F51 PC509F1040000145xx PC509F104000014001 PC5095204000010816 PC5095104000010816 PC509F02N000014501 PC509E02M000009017
Notes: 1. No further development for these upgrade kits. 2. The software versions may be displayed by selecting Status Report from the Service menu, or by selecting Status Panel/ Software Version/Set Date and Time from the Service menu. 3. Stations in systems running SZ2.0.3 are not software download capable.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
7-13
Table 7-5 CLN6960 Station Control Boards (IntelliRepeater 5.0 Stations) RSS Version Compatibility RSS Version Release R10.00.00 R10.01.00 R10.02.00 Release SZ5.0 SCM: P651 SIMM 0180706F51 App Sftwr PC509F1050000501500 Boot2 PC509F022000501001 EXC R10.03.00 SCM: P651 SIMM App Sftwr Boot2 EXC R10.04.00 R10.05.00 R10.06.00 SCM: P651 SIMM 0180706F51 App Sftwr PC509F105000501502 Boot2 PC509F022000501001 EXC R10.07.00 R10.08.00 R10.11.00 R10.12.00 R12.01.00 R12.02.00 R12.03.00 Notes: 1. The software versions may be displayed by selecting Status Report from the Service menu, or by selecting Status Panel/ Software Version/Set Date and Time from the Service menu. SCM: P651 SIMM 0180706F51 App Sftwr PC509F105000501504 Boot2 PC509F022000501001 EXC PC5093104000009009 SCM Boot EXC IR_005_01_504 B2_005_01_001 020.09.009 PC5093104000009005 SCM Boot EXC IR_005_01_504 B2_005_01_001 020.09.009 0180706F51 PC509F1050000501501 PC509F022000501001 PC5093104000009005 SCM Boot EXC IR_005_01_502 B2_005_01_001 020.09.005 PC5093104000009005 SCM Boot EXC IR_005_01_501 B2_005_01_001 020.09.005 Software/IC Part Numbers SCM Boot EXC Software Version1 IR_005_01_500 B2_005_01_001 020.09.005
SCM P651 SIMM 0180706F51 App Sftwr PC509F105000501504 Boot2 PC509F022000501001 EXC PC509E02M000009010
7-14
688 1085E 35-AN
0 6/30 /201 1
Table 7-6 CLN7462 Station Control Boards (Limited QUANTAR) RSS Version Compatibility RSS Version Release Release SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 EXC: R10.05.00 R10.05 SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 EXC: R10.06.00 R10.06 SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 EXC: R10.07.00 R10.07 R10.08.00 SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 EXC: PC5095204000010021 PC5095104000010021 PC5093104000009005 0180706F47 KC509024000100700 PC5091002000010016 PC5095204000010018 PC5095104000010018 PC5093104000009005 SCM WL Boot EXC LQ_020_10_717 WL_020_10_021 B2_020_10_016 020.09.005 0180706F47 KC509024000100600 PC5091002000010012 PC5095204000010012 PC5095104000010012 PC5093104000009005 SCM WL Boot EXC LQ_020_10_712 WL_020_10_018 B2_020_10_012 020.09.005 0180706F47 KC509024000100500 PC5091002000010007 PC5095204000010008 PC5095104000010008 PC5093104000009005 SCM WL Boot EXC LQ_020_10_708 WL_020_10_012 B2_020_10_007 020.09.005 0180706F47 KC509024000100400 PC5091002000010004 Software/IC Part Numbers SCM WL Boot EXC Software Version1 LQ_020_10_703 WL_020_10_008 B2_020_10_004 020.09.005
R10.04.00 R10.04
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
7-15
RSS PROGRAM VERSIONS COMPATIBILITY
Table 7-6 CLN7462 Station Control Boards (Limited QUANTAR) RSS Version Compatibility (continued) RSS Version Release Release SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 EXC: R10.12.00 R10.12 SCM: P651 SIMM App Sftwr Boot2 WL: U134 U135 EXC: Notes: 1. The software versions may be displayed by selecting Status Report from the Service menu, or by selecting Status Panel/Software Version/Set Date and Time from the Service menu. PC5095204000010025 PC5095104000010025 PC509E02M000009010 0180706F47 PC509F02H000010737 PC5091002000010022 PC5095204000010025 PC5095104000010025 PC5093104000009009 SCM WL Boot EXC LQ_020_10_737 WL_020_10_025 B2_020_10_022 020.09.009 0180706F47 KC509024000101100 PC5091002000010022 Software/IC Part Numbers SCM WL Boot EXC Software Version1 LQ_020_10_731 WL_020_10_025 B2_020_10_022 020.09.009
R10.11.00 R10.11
RSS Program Versions Compatibility ...................................

In general, each new version of the RSS program is backward compatible with previous versions. The following describes specific backward compatibility issues associated with the RSS program release version covered in this guide for RSS version R14. R14 is 100% backward compatible with conventional, 6809 trunking, and IntelliRepeater station firmware as shown in the Table 7-1 through Table 7-6 with the following exceptions: The new RSS is a graphical user interface (GUI) and so the information is presented in a more intuitive and familiar Windows format. Due to added fields and screens, you may notice that these new fields are filled with default values. Similarly, you may receive error messages if you try to access these new fields. Ignore the default values and close the error message window. Operation of the RSS or station is not affected. Beginning with Release 12, Securenet was cancelled. Codeplugs configured for Securenet cannot be upgraded beyond version 10.
..
7-16
688 1085E 35-AN
0 6/30 /201 1
RETRIEVING STATION SOFTWARE VERSIONS
Beginning with Release 13, ASTRO VSELP was cancelled. Codeplugs configured for ASTRO VSELP cannot be upgraded beyond version 12. Version 14 supports 800 MHz rebanding. To support rebanding of older 800 MHz systems, the IntelliRepeater application allows the operation of Securenet and ASTRO VSELP as well as ANALOG and ASTRO CAI. Thus Version 14 allows IntelliRepeater codeplugs configured for either Securenet or ASTRO VSELP to be upgraded to version 14. Version 14 does not allow Conventional or 6809 Trunking codeplugs configured for either Securenet or ASTRO VSELP to be upgraded beyond the limits imposed above, version 10 and version 12, respectively.
IMPORTANT
RSS R1.00, R2.00, R3.00, and R3.01 are not forward compatible with station firmware R4.00 and later. These earlier RSS versions cannot read the later Version station codeplugs and display a warning message to the effect if attempted.
NOTE
To support the various versions of frozen software and cancelled features, the RSS provides a default training codeplug for versions 10,12,13, and 14.
NOTE
The RSS does not support Version 11 of the codeplug. Version 11 is supported by the Customer Service Software (CSS).
Retrieving Station Software Versions ...................................

You must provide the stations current software version and its name when contacting Motorolas System Support Center (SSC). To access software version information from the connected station, perform the following procedure:
1.
Connect to the station as outlined in Connecting the PC to the Device RSS Port on page 2-11. Launch the RSS program as outlined in Launching the RSS Program on page 2-12. Read the connected stations codeplug as outlined in Reading the Device Codeplug on page 2-14. Click the + next to Service in the navigation pane to expand the service node. Click Version Screen in the Service tree. The information pane displays the current version information as shown in the example below.
..
2. 3.
4. 5.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
7-17
RETRIEVING COMPARATOR SOFTWARE VERSIONS AND BACKPLANE ID
Retrieving Comparator Software Versions and Backplane ID ...................................

You must provide the comparators current software version and its backplane ID when contacting Motorolas System Support Center (SSC). To access software version information from the connected station, perform the following procedure:
1.
Connect to the comparator as outlined in Connecting the PC to the Device RSS Port on page 2-11. Launch the RSS program as outlined in Launching the RSS Program on page 2-12. Read the connected comparators codeplug as outlined in Reading the Device Codeplug on page 2-14. Click the + next to Service in the navigation pane to expand the service node. Click Version screen in the Service tree. The information pane displays the current version information as shown in the examples below.
..
2. 3.
4. 5.
7-18
688 1085E 35-AN
0 6/30 /201 1
PERFORMING UPGRADES
Primary Comparator in an Expanded Configuration
Standard Comparator or Secondary Comparator in an Expanded Configuration
Performing Upgrades ................................... ..

There are two possible upgrade paths: Upgrading a stations codeplug to R14 firmware. Upgrading an archived codeplug file of a previous version of firmware to R14 firmware.
Upgrading the Stations Codeplug

You can upgrade the stations current codeplug to that of this RSS codeplug version.
1.
Check the current version of the stations codeplug loaded in the RSS. See Verifying the Devices Configuration Data on page 3-3. Check the RSSs codeplug version by clicking Help then About. The About window appears.
2.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
7-19
PERFORMING UPGRADES
If you would like to see more details about the RSS, click Version Details. See the example below.
3.
If you wish to upgrade the stations codeplug version, click OK to close the Versions window , then from the Tools menu, select Codeplug upgrade.
4.
Click Upgrade to upgrade the stations codeplug. The following window appears.
7-20
688 1085E 35-AN
0 6/30 /201 1
PERFORMING UPGRADES
5.
Click Continue to write the upgraded codeplug to the station and complete the upgrade process.
Upgrading an Archived Codeplug File

1. 2. 3.
Launch the RSS program. Open the archive file to upgrade. From the Tools menu, select Codeplug upgrade. The Upgrade Codeplug Data windows appears.
4.
Click Upgrade to upgrade the stations codeplug. The following window appears.
5.
Click Continue to write the upgraded codeplug to the station and complete the upgrade process. Save the upgraded codeplug archive for installation in a station later.
6.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
7-21
FEATURES AND SYSTEM CAPABILITIES
Features and System Capabilities ...................................

The following figures provide a summary of the features available in each release.
STANDARD SOFTWARE FEATURES Basic TRC PL Battery Revert * * = requires optional hardware
..
CONVENTIONAL LOCAL AREA ANALOG CONVENTIONAL LOCAL AREA SECURENET (X599) ADD SPECTRA-TAC (X269)
ADD SAM REPEATER ACCESS (X932) CONVENTIONAL (LOCAL AREA ANALOG WITH REPEATER ACCESS)
ADD SECURENET (Enable Using RSS)
CONVENTIONAL (LOCAL AREA SECURENET)
CONVENTIONAL (WIDE AREA ANALOG)
STATIONS SUPPORTED: Quantro 800 MHz QUANTAR VHF R1 and R2 Quantro UHF R1 and R2 Quantro 350 W VHF R1 and R2
ADD SAM REPEATER ACCESS (X932)
ADD SPECTRA-TAC (X269)
ADD SECURENET (Enable Using RSS)
CONVENTIONAL (LOCAL AREA SECURENET WITH REPEATER ACCESS)
CONVENTIONAL (WIDE AREA SECURENET)
Figure 7-1 Release R1.00 Features and System Capabilities Conventional
7-22
688 1085E 35-AN
0 6/30 /201 1
STATIONS SUPPORTED Quantro 800 MHz QUANTAR VHF R1 and R2 Quantro UHF R1 through R3 QUANTAR 900 MHz Quantro 350W VHF R1 and R2
STANDARD SOFTWARE FEATURES Basic TRC PL DPL Battery Revert * Alarm Tones E & M Keying 12.5 kHz Channels 5 MHZ External Reference * = requires optional hardware
CONVENTIONAL LOCAL AREA ANALOG CONVENTIONAL LOCAL AREA ASTRO CONVENTIONAL LOCAL AREA SECURENET (X599)
ADD SECURENET (Enable using RSS)
ADD ASTRO (Enable using RSS)
CONVENTIONAL (LOCAL AREA ANALOG WITH REPEATER ACCESS)
CONVENTIONAL (LOCAL AREASECURENET)
CONVENTIONAL (WIDE AREA ANALOG)
CONVENTIONAL (LOCAL AREA ASTRO )
ADD SECURENET (Enable using RSS)
CONVENTIONAL (LOCAL AREASECURENET WITH REPEATER ACCESS )
CONVENTIONAL (LOCAL AREA ASTRO WITH REPEATER ACCESS )
Figure 7-2 Release R2.00 Features and System Capabilities - Conventional
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
7-23
7-24
STANDARD SOFTWARE FEATURES
STATIONS SUPPORTED Basic TRC PL DPL
CONVENTIONAL LOCAL AREA ANALOG CONVENTIONAL LOCAL AREA ASTRO CONVENTIONAL LOCAL AREASECURENET
Battery Revert * Alarm Tones E & M Keying
Quantro 800 MHz
Quantar VHF R1 and R2
Quantro UHF R1 through R4
Quantar 900 MHz
(X599) ADD SECURENET (Enable Using RSS) ADD SPECTRA-TAC (X269)

UHSO * 12.5 kHz Channels
Quantro 350 W VHF R1 and R2
5 MHz/10MHz Ext. Reference
* = requires optional hardware
ADD SAM REPEATER ACCESS (X932) ADD ASTRO (Enable Using RSS)
CONVENTIONAL (LOCAL AREA ANALOG CONVENTIONAL (LOCAL AREASECURENET) CONVENTIONAL (WIDE AREA ANALOG)
CONVENTIONAL (LOCAL AREA ASTRO ) ADD SIMULCAST (X777) (Includes X269)
WITH REPEATER ACCESS) ADD SECURENET (Enable Using RSS) ADD SPECTRA-TAC (X269)
ADD SAM REPEATER ACCESS (X932) ADD SAM REPEATER ACCESS (X932)
CONVENTIONAL SIMULCAST (WIDE AREA ANALOG) CONVENTIONAL (WIDE AREA SECURENET) ADD SAM REPEATER ACCESS (X932)
Figure 7-3 Release R3.00 / R3.01 Features and System Capabilities - Conventional
688 1085E 35-AN
CONVENTIONAL SIMULCAST (WIDE AREA SECURENET)
0 6/30 /201 1
SOFTWARE FEATURES
Quantro 800 MHz Quantar 800 MHz
68 8 10 85 E3 5 -A N
Quantar 900 MHz
CONVENTIONAL LOCAL AREA ANALOG

Alarm Tones
Battery Revert *
(X597)
E & M Keying 12.5 kHz Channels 5 MHz/10 MHz Ext. Reference ASTRO 1.5 OPTIONAL SOFTWARE FEATURES UHSO * 8-Wire Capability * MRTI (Phone Patch) * Multi-Coded Squelch
06 / 30 / 20 11
ADD SECURENET (X598) ADD SPECTRA-TAC (X269)
ADD ASTRO (X599)
CONVENTIONAL (LOCAL AREA ASTRO ) ADD SIMULCAST (X777) (Includes X269)
WITH REPEATER ACCESS)
ADD SPECTRA-TAC (X269) ADD SECURENET (X598)
CONVENTIONAL SIMULCAST (WIDE AREA ANALOG)
CONVENTIONAL (LOCAL AREASECURENET WITH REPEATER ACCESS ) ADD SIMULCAST (X777)
CONVENTIONAL (WIDE AREA SECURENET) ADD SAM REPEATER ACCESS (X932)
7-25
7-26
SOFTWARE FEATURES Basic TRC PL DPL
STATIONS SUPPORTED
QuantarUHF R1, 25 W; R2, 110 W; R4, 100 W
QuantroUHF R1 through R4 Alarm Tones
CONVENTIONAL LOCAL AREA ANALOG (X597)

E & M Keying 12.5 kHz Channels
Battery Revert *
Quantar 900 MHz
5 MHz/10 MHz Ext. Reference
OPTIONAL SOFTWARE FEATURES UHSO *
ADD SAM REPEATER ACCESS (X932) ADD SECURENET (X598) ADD SPECTRA-TAC (X269) ADD ASTRO (X599)
8-Wire Capability * MRTI (Phone Patch) * Multi-Coded Squelch Remote RSS; includes: Station Password Protection Remote Dial-Up Capability * ASTRO1.5
WITH REPEATER ACCESS) ADD SPECTRA-TAC (X269) ADD SECURENET (X598)
ADD SIMULCAST (X777) (Includes X269)

CONVENTIONAL SIMULCAST (WIDE AREA ANALOG) CONVENTIONAL (WIDE AREA SECURENET) ADD SAM REPEATER ACCESS (X932) ADD SIMULCAST (X777)
688 1085E 35-AN
0 6/30 /201 1
SOFTWARE FEATURES
68 8 10 85 E3 5 -A N
Quantar UHF R1, 25 W; R2, 110 W; R4, 100 W
Battery Revert * Alarm Tones E & M Keying 12.5 kHz Channels 5 MHz/10 MHz Ext. Reference
Quantar 900 MHz
06 / 30 / 20 11
ADDSECURENET (X598) ADD SPECTRA-TAC (X269) ADD ASTRO (X599)
OPTIONAL SOFTWARE FEATURES UHSO * 8-Wire Capability * MRTI (Phone Patch) * Multi-Coded Squelch Remote RSS; includes: Station Password Protection Remote Dial-Up Capability * ASTRO 1.5.1
WITH REPEATER ACCESS) ADD SIMULCAST (X777) (Includes X269) ADD SPECTRA-TAC (X269) ADD SECURENET (X598)
CONVENTIONAL (WIDE AREA SECURENET) ADD SIMULCAST (X777) ADD SAM REPEATER ACCESS (X932) CONVENTIONAL (LOCAL AREA ASTRO)
CONVENTIONAL SIMULCAST
7-27
7-28
SOFTWARE FEATURES
STATIONS SUPPORTED
Quantro 800 MHz Quantar 800 MHz Basic TRC Enhanced TRC DC Remote Control PL DPL Battery Revert * Alarm Tones E & M Keying 12.5 kHz Channels 5 MHz/10 MHz Ext. Reference
Quantar
UHF R1/R2, 25 W; R1/R2, 110 W; R3, 110 W; R4, 100 W
Quantar 900 MHz
ADD SAM REPEATER ACCESS (X932) ADD SECURENET (X598) ADD SPECTRA-TAC (X269) ADD ASTRO (X599)
OPTIONAL SOFTWARE FEATURES UHSO * 8-Wire Capability * MRTI (Phone Patch) * Multi-Coded Squelch WildCard Capability Widespace 2nd Receiver * Remote RSS; includes: Station Password Protection Remote Dial-Up Capability * ASTRO 1.5.1 * = requires optional hardware

ADD SPECTRA-TAC (X269) ADD SECURENET (X598) ADD SIMULCAST (X777) (Includes X269) CONVENTIONAL SIMULCAST (WIDE AREA ANALOG) ADD SAM REPEATER ACCESS (X932) CONVENTIONAL (WIDE AREA SECURENET) ADD SIMULCAST (X777)
688 1085E 35-AN
0 6/30 /201 1
STATIONS SUPPORTED Basic TRC Enhanced TRC DC Remote Control
SOFTWARE FEATURES
Quantro 800 MHz Quantar 800 MHz Wireline Squelch PL DPL Battery Revert * Alarm Tones E & M Keying 12.5 kHz Channels
68 8 10 85 E3 5 -A N
Quantar UHF R1/R2, 25 W; R1/R2, 110 W; R3, 110 W; R4, 100 W
Quantar 900 MHz
Figure 7-8 Release R07.02.02 Features and System Capabilities - Conventional
06 / 30 / 20 11
ADD SECURENET (X598)
ADD ASTRO (X599)
5 MHz/10 MHz Ext. Reference OPTIONAL SOFTWARE FEATURES UHSO * 8-Wire Capability * MRTI (Phone Patch) * Multi-Coded Squelch WildCard Capability Widespace 2nd Receiver * Main/Standby Remote RSS; includes:
ASTRO 1.7 * = requires optional hardware
ADD SAM REPEATER ACCESS (X932) ADD SPECTRA-TAC (X269)
ADD SIMULCAST (X777) (Includes X269) ADD SECURENET (X598) CONVENTIONAL SIMULCAST (WIDE AREA ANALOG) CONVENTIONAL (WIDE AREA SECURENET) ADD SIMULCAST (X777) ADD SAM REPEATER ACCESS (X932)
7-29
7-30
SOFTWARE FEATURES Basic TRC Enhanced TRC DC Remote Control
STATIONS SUPPORTED
Quantro 800 MHz Quantar 800 MHz Wireline Squelch PL DPL Battery Revert * Alarm Tones E & M Keying 12.5 kHz Channels 5 MHz/10 MHz Ext. Reference OPTIONAL SOFTWARE FEATURES UHSO * 8-Wire Capability *
Quantar
UHF R1/R2, 25 W; R1/R2, 110 W; R3, 110 W; R4, 100 W
Quantar 900 MHz
ADD ASTRO (X599)
MRTI (Phone Patch) * Multi-Coded Squelch WildCard Capability Widespace 2nd Receiver * Main/Standby Remote RSS; includes:
Station Password Protection
Remote Dial-Up Capability * * = requires optional hardware
ADD SIMULCAST (X777) (Includes X269) CONVENTIONAL SIMULCAST
ASTRO 1.7
ADD SAM REPEATER ACCESS (X932) ADD SECURENET (X598) ADD SPECTRA-TAC (X269)
(WIDE AREA ANALOG)
Figure 7-9 Release R08.00.00-R08.03.00 Features and System Capabilities - Conventional

CONVENTIONAL (WIDE AREA SECURENET) ADD SIMULCAST (X777) ADD SPECTRA-TAC (X269) ADD SAM REPEATER ACCESS (X932) ADD SIMULCAST (X888)
688 1085E 35-AN
CONVENTIONAL (WIDE AREAASTRO )
CONVENTIONAL SIMULCAST (WIDE AREA ASTRO)
0 6/30 /201 1
STATIONS SUPPORTED Quantro 800 MHz Quantar 800 MHz Quantar VHF R1 and R2 Quantar UHF R1/R2, 25 W; R1/R2, 110 W; R3, 110 W; R4, 100 W
STANDARD SOFTWARE FEATURES Wireline Squelch PL DPL Battery Revert * Alarm Tones 12.5 kHz Channels 5 MHz/10 MHz Ext. Reference Software Download Capability
OPTIONAL SOFTWARE FEATURES UHSO * ASTRO CAI 3.0 Remote RSS; includes: Station Password Protection Remote Dial-Up Capability * * = requires optional hardware
Quantro UHF R1 through R4 Quantar 900 MHz Quantro 350 W VHF R1 and R2
CONVENTIONAL LOCAL AREA ASTRO CAI (X806)
ADD ASTRO SIMULCAST (X888)
CONVENTIONAL (WIDE AREA ASTRO CAI)
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
7-31
7-32
STANDARD SOFTWARE FEATURES Basic TRC Enhanced TRC DC Remote Control
STATIONS SUPPORTED
Quantro 800 MHz Quantar 800 MHz Wireline Squelch PL DPL Battery Revert * Alarm Tones E & M Keying 12.5 kHz Channels 5 MHz/10 MHz Ext. Reference Software Download Capability
Quantar 900 MHz
Quantro 900 MHz Quantro 350 W VHF R1 and R2
ADD SECURENET (X598) ADD SIMULCAST (X777) (Includes X269) ADD ASTRO (X599 VSELP) ADD SPECTRA-TAC (X269) OR (X806 IMBE)
OPTIONAL SOFTWARE FEATURES UHSO * 8-Wire Capability * MRTI (Phone Patch) * Multi-Coded Squelch WildCard Capability Widespace 2nd Receiver * Main/Standby Channel Scanning Remote RSS; includes: Station Password Protection Remote Dial-Up Capability * ASTRO 1.7 ASTRO CAI 3.0

ADD SPECTRA-TAC (X269) ADD SECURENET (X598)
CONVENTIONAL (WIDE AREA SECURENET) ADD SAM REPEATER ACCESS (X932) ADD SPECTRA-TAC (X269) CONVENTIONAL (WIDE AREAASTRO ) ADD SIMULCAST (X888)
688 1085E 35-AN
ADD SIMULCAST (X777) CONVENTIONAL SIMULCAST (WIDE AREA SECURENET)
CONVENTIONAL SIMULCAST (WIDE AREA ASTRO)
0 6/30 /201 1
STATIONS SUPPORTED Basic TRC Enhanced TRC DC Remote Control Wireline Squelch PL DPL Battery Revert * Alarm Tones E & M Keying
SOFTWARE FEATURES
68 8 10 85 E3 5 -A N
Quantar
UHF R1/R2, 25 W; R1/R2, 110 W; R3, 110 W; R4, 100 W
CONVENTIONAL LOCAL AREA ANALOG (X597) ADD SPECTRA-TAC (X269) ADD ASTRO (X599 VSELP) OR (X806 IMBE)

06 / 30 / 20 11
Quantar 900 MHz
12.5 kHz Channels 5 MHz/10 MHz Ext. Reference Software Download Capability
ADD SIMULCAST (X777) (Includes X269) CONVENTIONAL (LOCAL AREA SECURENET ) CONVENTIONAL (LOCAL AREA ASTRO ) ADD SECURENET (X598) CONVENTIONAL (WIDE AREA ANALOG)
OPTIONAL SOFTWARE FEATURES UHSO * 8-Wire Capability * MRTI (Phone Patch) * Multi-Coded Squelch
CONVENTIONAL (LOCAL AREA ANALOG
WITH REPEATER ACCESS) CONVENTIONAL SIMULCAST (WIDE AREA ANALOG)
WildCard Capability Widespace 2nd Receiver * Main/Standby Channel Scanning Simulcast Fallback In-Cabinet Repeat Remote RSS; includes: Station Password Protection
CONVENTIONAL (LOCAL AREA SCURENET WITH REPEATER ACCESS ) ADD SIMULCAST (X777)
CONVENTIONAL (WIDE AREA SECURENET ) ADD SAM REPEATER ACCESS (X932) ADD SPECTRA-TAC (X269) ADD SIMULCAST (X888)
Remote Dial-Up Capability * ASTRO 1.7 ASTRO CAI 3.0 * = requires optional hardware
CONVENTIONAL SIMULCAST (WIDE AREA SECURENET )
CONVENTIONAL (WIDE AREAASTRO)
CONVENTIONAL (LOCAL AREAASTRO WITH REPEATER ACCESS )
CONVENTIONAL SIMULCAST (WIDE AREAASTRO)
ADD FALLBACK/In-Cab REPEAT (U764)
CONVENTIONAL SIMULCAST (WIDE AREA SECURENET WITH FALLBACK INCAB REPEAT)
CONVENTIONAL (LOCAL AREAASTRO WITH REPEATER ACCESS AND FALLBACK IN-CAB REPEAT)
CONVENTIONAL SIMULCAST (WIDE AREA ANALOG WITH FALLBACK INCAB REPEAT)
7-33
7-34
SOFTWARE FEATURES Basic TRC Enhanced TRC DC Remote Control Wireline Squelch PL DPL Battery Revert * Alarm Tones E & M Keying 12.5 kHz Channels 5 MHz/10 MHz Ext. Reference Software Download Capability OPTIONAL SOFTWARE FEATURES
STATIONS SUPPORTED
Quantar
UHF R1/R2, 25 W; R1/R2, 110 W; R3, 110 W; R4, 100 W
CONVENTIONAL LOCAL AREA ANALOG (X597) ADD SECURENET (X598) ADD SIMULCAST (X777) (Includes X269) ADD ASTRO (X599 VSELP) OR (X806 IMBE) ADD SPECTRA-TAC (X269)
Quantar 900 MHz
CONVENTIONAL (LOCAL AREA ANALOG CONVENTIONAL (LOCAL AREA SECURENET ) CONVENTIONAL (LOCAL AREA ASTRO ) CONVENTIONAL (WIDE AREA ANALOG)
UHSO * 8-Wire Capability * MRTI (Phone Patch) * Multi-Coded Squelch
WITH REPEATER ACCESS) ADD SECURENET (X598)
WildCard Capability Widespace 2nd Receiver * Main/Standby Channel Scanning Simulcast Fallback In-Cabinet Repeat Remote RSS; includes: Station Password Protection
ADD SPECTRA-TAC (X269) ADD SAM REPEATER ACCESS (X932)
CONVENTIONAL (LOCAL AREA SECURENET WITH REPEATER ACCESS ) CONVENTIONAL (WIDE AREA SECURENET )
Remote Dial-Up Capability * ASTRO 1.7 ASTRO CAI 3.0
ADD SIMULCAST (X888) ADD SAM REPEATER ACCESS (X932)
Fast Keyup * = requires optional hardware
ADD SIMULCAST (X777)
Figure 7-13 Release R09.05.00/R09.06.00 Features and System Capabilities - Conventional

CONVENTIONAL SIMULCAST (WIDE AREA SECURENET) CONVENTIONAL (WIDE AREA ASTRO) CONVENTIONAL (LOCAL AREA ASTRO WITH REPEATER ACCESS ) CONVENTIONAL SIMULCAST (WIDE AREAASTRO) ADD FALLBACK/In-Cab REPEAT (U764) ADD FALLBACK/In-Cab REPEAT (U764) ADD FALLBACK/In-Cab REPEAT (U764)
688 1085E 35-AN
0 6/30 /201 1
STATIONS SUPPORTED Basic TRC Enhanced TRC DC Remote Control Wireline Squelch PL DPL Battery Revert * Alarm Tones E & M Keying 12.5 kHz Channels 5 MHz/10 MHz Ext. Reference Software Download Capability SELECTCAST OPTIONAL SOFTWARE FEATURES
SOFTWARE FEATURES
68 8 10 85 E3 5 -A N
Quantar
UHF R1/R2, 25 W; R1/R2, 110 W; R3, 110 W; R4, 100 W
Limited QUANTAR UHF R3/R4, 110/100 W
Figure 7-14 Release R09.07.00/R10.00.00 through R10.08.00, R10.11.00, R10.12.00 Features and System Capabilities - Conventional
ADD SECURENET (X598) ADD SPECTRA-TAC (X269) ADD SIMULCAST (X777) (Includes X269)
06 / 30 / 20 11
Quantar 900 MHz
ADD ASTRO (X599 VSELP) OR (X806 IMBE)
CONVENTIONAL (LOCAL AREA ANALOG CONVENTIONAL (LOCAL AREA SECURENET ) CONVENTIONAL (LOCAL AREAASTRO ) CONVENTIONAL (WIDE AREA ANALOG)
UHSO * 8-Wire Capability * MRTI (Phone Patch) * Multi-Coded Squelch WildCard Capability Widespace 2nd Receiver * Main/Standby Channel Scanning Simulcast Fallback In-Cabinet Repeat Remote RSS; includes: Station Password Protection
ADD SAM REPEATER ACCESS (X932) ADD SECURENET (X598)
Remote Dial-Up Capability * ASTRO 1.7 ASTRO CAI 3.0
CONVENTIONAL (WIDE AREA ASTRO)
7-35
7-36
SOFTWARE FEATURES Basic TRC Enhanced TRC DC Remote Control Wireline Squelch PL DPL Battery Revert * Alarm Tones E & M Keying 12.5 kHz Channels 5 MHz/10 MHz Ext. Reference Software Download Capability SELECTCAST OPTIONAL SOFTWARE FEATURES
STATIONS SUPPORTED
Quantar UHF R1/R2, 25 W; R0/R1/R2, 110 W; R3, 110 W; R4, 100 W
Limited QUANTAR UHF R3/R4, 110/100 W
Quantar 900 MHz
ADD ASTRO (X599 VSELP) OR (X806 IMBE) ADD SPECTRA-TAC (X269) ADD SAM REPEATER ACCESS (X932) ADD SIMULCAST (X777) (Includes X269)
CONVENTIONAL (LOCAL AREA ANALOG CONVENTIONAL (WIDE AREA ANALOG) CONVENTIONAL (LOCAL AREAASTRO ) WITH REPEATER ACCESS) CONVENTIONAL SIMULCAST (WIDE AREA ANALOG)
UHSO * 8-Wire Capability * MRTI (Phone Patch) * Multi-Coded Squelch WildCard Capability Widespace 2nd Receiver * Main/Standby Channel Scanning
ADD SPECTRA-TAC (X269) ADD SIMULCAST (X888)
Simulcast Fallback In-Cabinet Repeat Remote RSS; includes: Station Password Protection Remote Dial-Up Capability * ASTRO 1.7 ASTRO CAI 3.0/3.1 Fast Keyup * = requires optional hardware
Figure 7-15 Release R12.01.00 through R12.03.00 Features and System Capabilities - Conventional
ADD FALLBACK/In-Cab REPEAT (U764) ADD FALLBACK/In-Cab REPEAT (U764)
688 1085E 35-AN
0 6/30 /201 1
SOFTWARE FEATURES Basic TRC Enhanced TRC DC Remote Control Wireline Squelch PL DPL Battery Revert *
STATIONS SUPPORTED
68 8 10 85 E3 5 -A N
Quantar UHF R1/R2, 25 W; R0/R1/R2, 110 W; R3, 110 W; R4,100 W
Limited Quantar UHF R3/R4, 110/100 W
Figure 7-16 Release R13.00.00 through R13.02.00 Features and System Capabilities - Conventional
ADD ASTRO (X806 IMBE) ADD SIMULCAST (X777) (Includes X269)
Alarm Tones E & M Keying 12.5 kHz Channels 5 MHz/10 MHz Ext. Reference Software Download Capability SELECTCAST Multi NAC OPTIONAL SOFTWARE FEATURES
06 / 30 / 20 11
Quantar 900 MHz
CONVENTIONAL (LOCAL AREA ANALOG CONVENTIONAL (WIDE AREA ANALOG) CONVENTIONAL (LOCAL AREAASTRO ) WITH REPEATER ACCESS)
UHSO * 8-Wire Capability * MRTI (Phone Patch) * Multi-Coded Squelch
WildCard Capability Widespace 2nd Receiver * Main/Standby Channel Scanning
Simulcast Fallback In-Cabinet Repeat Remote RSS; includes: Station Password Protection Remote Dial-Up Capability * ASTRO 1.7 ASTRO CAI 3.0/3.1
7-37
SOFTWARE FEATURES Basic TRC Enhanced TRC DC Remote Control Wireline Squelch PL DPL
7-38
CONVENTIONAL LOCAL AREA ANALOG (X597) ADD SPECTRA-TAC (X269)
Battery Revert * Alarm Tones E & M Keying 12.5 kHz Channels 5 MHz/10 MHz Ext. Reference Software Download Capability SELECTCAST Multi NAC OPTIONAL
STATIONS SUPPORTED
Quantar UHF R1/R2, 25 W; R0/R1/R2, 110 W; R3, 110 W; R4, 100 W
Limited Quantar UHF R3/R4, 110/100 W
Quantar 900 MHz
ADD ASTRO (X806 IMBE) ADD SIMULCAST (X777) (Includes X269)
CONVENTIONAL (LOCAL AREA ANALOG CONVENTIONAL (WIDE AREA ANALOG) CONVENTIONAL (LOCAL AREAASTRO ) WITH REPEATER ACCESS) CONVENTIONAL SIMULCAST (WIDE AREA ANALOG)
SOFTWARE FEATURES UHSO * 8-Wire Capability * MRTI (Phone Patch) * Multi-Coded Squelch WildCard Capability Widespace 2nd Receiver * Main/Standby Channel Scanning Simulcast Fallback In-Cabinet Repeat Remote RSS; includes: Station Password Protection Remote Dial-Up Capability * ASTRO 1.7 ASTRO CAI 3.0/3.1

ADD SAM REPEATER ACCESS (X932) ADD SIMULCAST (X888)
688 1085E 35-AN
0 6/30 /201 1
STATIONS SUPPORTED Quantro 800 MHz QUANTAR VHF R1 and R2 Quantro UHF R1 through R3 QUANTAR 900 MHz Quantro 350 W VHF R1 and R2
STANDARD SOFTWARE FEATURES Basic TRC Battery Revert * 12.5 kHz Channels 5 MHZ External Reference Failsoft * = requires optional hardware
6809 TRUNKING (SINGLE SITE ANALOG) (X997)
6809 TRUNKING (SINGLE SITE SECURENET ) (X996)
ADD CONSOLE PRIORITY INTERFACE (C115)
6809 TRUNKING (WIDE AREA ANALOG)
6809 TRUNKING (SINGLE SITE ANALOG W/ CPI)
6809 TRUNKING (WIDE AREA SECURENET)
Figure 7-18 Release R2.00 Features and System Capabilities - 6809 Trunking
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
7-39
STATIONS SUPPORTED Quantro 800 MHz QUANTAR VHF R1 and R2 Quantro UHF R1 through R3 QUANTAR 900 MHz Quantro 350 W VHF R1 and R2
STANDARD SOFTWARE FEATURES Basic TRC Battery Revert * 12.5 kHz Channels 5 MHz/10 MHz External Reference UHSO* Failsoft * = requires optional hardware
6809 TRUNKING (SINGLE SITE ANALOG) (X997) ADD SPECTRA-TAC (X269) ADD SIMULCAST (X777) (Includes X269) ADD CONSOLE PRIORITY INTERFACE (C115)
6809 TRUNKING (SINGLE SITE SECURENET ) (X996) ADD SIMULCAST (X777) (Includes X269)
6809 TRUNKING (WIDE AREA ANALOG)
6809 TRUNKING (SINGLE SITE ANALOG WITH CPI)
6809 TRUNKING SIMULCAST (WIDE AREA ANALOG)
6809 TRUNKING SIMULCAST (WIDE AREA SECURENET )
Figure 7-19 Release R3.00 / R3.01 Features and System Capabilities - 6809 Trunking
7-40
688 1085E 35-AN
0 6/30 /201 1
68 8 10 85 E3 5 -A N STANDARD SOFTWARE FEATURES
06 / 30 / 20 11
6809 TRUNKING (SINGLE SITE ANALOG) (X997) ADD SPECTRA-TAC (X269) (X996) (SINGLE SITE SECURENET )
6809 TRUNKING
Basic TRC Battery Revert * 12.5 kHz Channels 5 MHz/10 MHz Ext. Reference
OPTIONAL SOFTWARE FEATURES UHSO * Failsoft
ADD CONSOLE PRIORITY INTERFACE (C115) (Includes 8-Wire Capability) ADD SIMULCAST (X777) (Includes X269)
8-Wire Capability *
6809 TRUNKING
(WIDE AREA ANALOG)
ADD SIMULCAST (X777) (Includes X269)
STATIONS SUPPORTED
Quantro 800 MHz Quantar 800 MHz Quantar VHF R1 and R2
Quantar 900 MHz
7-41
7-42
STANDARD SOFTWARE FEATURES Basic TRC Battery Revert * 12.5 kHz Channels 5 MHz/10 MHz Ext. Reference
STATIONS SUPPORTED
Quantar 900 MHz
6809 TRUNKING (SINGLE SITE ANALOG) (X997) (X996) (SINGLE SITE SECURENET )
6809 TRUNKING
OPTIONAL SOFTWARE FEATURES UHSO * Failsoft 8-Wire Capability * Remote RSS; includes: Station Password Protection Remote Dial-Up Capability * * = requires optional hardware
ADD SPECTRA-TAC (X269) ADD CONSOLE PRIORITY INTERFACE ADD SIMULCAST (C115) (X777) (Includes 8-Wire (Includes X269) Capability) ADD SPECTRA-TAC (X269)
ADD SIMULCAST (X777) (Includes X269) 6809 TRUNKING (SINGLE SITE ANALOG W/ CPI) 6809 TRUNKING (WIDE AREA SECURENET) 6809 TRUNKING SIMULCAST (WIDE AREA SECURENET ) 6809 TRUNKING SIMULCAST (WIDE AREA ANALOG)
6809 TRUNKING
(WIDE AREA ANALOG)
688 1085E 35-AN
0 6/30 /201 1
STATIONS SUPPORTED Quantro 800 MHz Quantar 800 MHz SOFTWARE FEATURES UHSO * Failsoft 8-Wire Capability * 12.5 kHz Channels 5 MHz/10MHz Ext. Reference Remote RSS; includes: Station Password Protection Remote Dial-Up Capability * SMARTZONE 2.0.3 * = requires optional hardware Battery Revert * Basic TRC SOFTWARE FEATURES
68 8 10 85 E3 5 -A N
Quantro UHF R1 though R4
Quantar 900 MHz
06 / 30 / 20 11
6809 TRUNKING
6809 ASTRO TRUNKING (SINGLE SITE ASTRO ) (X992)
SMARTZONE 6809 ASTRO TRUNKING (WIDE AREA ASTRO ) (X989)
ADD ADD SPECTRA-TAC CONSOLE PRIORITY (X269) INTERFACE (C115) (Includes 8-Wire Capability) ADD ANALOG SIMULCAST (X777) (Includes X269) ADD SPECTRA-TAC (X269)
ADD ANALOG SIMULCAST (X777) (Includes X269)
ADD GPS SIMULCAST (X888) (Requires X889 V.24 Board)
6809 TRUNKING
(WIDE AREA ANALOG)
6809 TRUNKING 6809 TRUNKING SIMULCAST (WIDE AREA ANALOG) SIMULCAST (WIDE AREA SECURENET )
6809 TRUNKING (WIDE AREAASTRO )
6809 ASTRO TRUNKING SIMULCAST (WIDE AREA ASTRO)
7-43
7-44
SOFTWARE FEATURES UHSO * Failsoft 8-Wire Capability * 12.5 kHz Channels 5 MHz/10 MHz Ext. Reference WildCard Capability Remote RSS; includes: Station Password Protection Remote Dial-Up Capability * SMARTZONE 2.0.3 * = requires optional hardware Battery Revert * Basic TRC SOFTWARE FEATURES
STATIONS SUPPORTED
Quantar
UHF R1/R2, 25 W; R1/R2, 110 W; R3, 110 W; R4, 100 W
Quantar 900 MHz
6809 TRUNKING (SINGLE SITE ANALOG) (X997) (X992) ADD CONSOLE PRIORITY INTERFACE (C115) (Includes 8-Wire Capability) ADD ANALOG SIMULCAST (X777) (Includes X269) ADD SPECTRA-TAC (X269) ADD ANALOG SIMULCAST (X777) (Includes X269) (X996) (SINGLE SITE ASTRO ) (SINGLE SITE SECURENET )
6809 TRUNKING
6809 ASTRO TRUNKING
SMARTZONE 6809 ASTRO TRUNKING (WIDE AREA ASTRO ) (X989)
6809 TRUNKING 6809 TRUNKING (WIDE AREA SECURENET) (SINGLE SITE ANALOG W/ CPI) 6809 TRUNKING 6809 TRUNKING SIMULCAST (WIDE AREA ANALOG) SIMULCAST (WIDE AREA SECURENET )
6809 TRUNKING
(WIDE AREA ANALOG)
688 1085E 35-AN
0 6/30 /201 1
STATIONS SUPPORTED OPTIONAL SOFTWARE FEATURES UHSO * Failsoft 8-Wire Capability * WildCard Capability Remote RSS; includes: Station Password Protection Remote Dial-Up Capability * SMARTZONE 2.0.3 SMARTNET 2.0.2 * = requires optional hardware 12.5 kHz Channels Remote Dial-Up Capability * Battery Revert * Basic TRC STANDARD SOFTWARE FEATURES
68 8 10 85 E3 5 -A N
Quantar
UHF R1/R2, 25 W; R1/R2, 110 W; R3, 110 W; R4, 100 W
Figure 7-24 Release R07.02.02 Features and System Capabilities - 6809 Trunking
06 / 30 / 20 11
Quantar 900 MHz
6809 TRUNKING
6809 ASTRO TRUNKING (SINGLE SITE ASTRO ) (X992)
SMARTZONE 6809 ASTRO TRUNKING (WIDE AREA ASTRO ) (X989) ADD GPS SIMULCAST (X888)
ADD SPECTRA-TAC (X269) (Includes 8-Wire Capability)
ADD CONSOLE PRIORITY INTERFACE (C115)
ADD SPECTRA-TAC (X269) ADD ANALOG SIMULCAST (X777) (Includes X269)
(Requires X889 V.24 Board)
6809 TRUNKING
(WIDE AREA ANALOG)
7-45
STATIONS SUPPORTED Quantro 800 MHz Quantar 800 MHz Quantar VHF R1 and R2 Quantar UHF R1/R2, 25 W; R1/R2, 110 W; R3, 110 W; R4, 100 W
SMARTZONE 6809 ASTRO TRUNKING (WIDE AREA ASTRO ) (X897 IMBE)
STANDARD SOFTWARE FEATURES Battery Revert * 12.5 kHz Channels 5 MHz/10MHz Ext. Reference Software Downloading Capability
Quantro UHF R1 through R4 Quantar 900 MHz Quantro 350 W VHF R1 and R2
OPTIONAL SOFTWARE FEATURES UHSO * Failsoft ASTRO CAI 3.0 Remote RSS; includes: Station Password Protection Remote Dial-Up Capability * SMARTZONE 2.0.3 SMARTZONE 3.0 SMARTNET 2.0.2
7-46
688 1085E 35-AN
0 6/30 /201 1
STATIONS SUPPORTED UHSO * Failsoft 8-Wire Capability * 12.5 kHz Channels 5 MHz/10 MHz Ext. Reference Software Downloading Capability WildCard Capability ASTRO CAI 3.0 Remote RSS; includes: Station Password Protection Remote Dial-Up Capability * SMARTZONE 2.0.3 SMARTZONE 3.0 SMARTNET 2.0.2 SMARTNET 3.0 * = requires optional hardware Battery Revert * Basic TRC
OPTIONAL SOFTWARE FEATURES
68 8 10 85 E3 5 -A N
Quantar
UHF R1/R2, 25 W; R1/R2, 110 W; R3, 110 W; R4, 100 W
06 / 30 / 20 11
Quantar 900 MHz Quantro 900 MHz Quantro 350 W VHF R1 and R2
6809 TRUNKING (SINGLE SITE ANALOG) (X997) (X996) (SINGLE SITE SECURENET ) 6809 TRUNKING 6809 ASTRO TRUNKING (SINGLE SITE ASTRO ) (X992 VSELP) ADD ANALOG SIMULCAST (X777) (Includes X269) ADD SPECTRA-TAC (X269) ADD ANALOG SIMULCAST (X777) (Includes X269)
SMARTZONE 6809 ASTRO TRUNKING (WIDE AREA ASTRO ) X897 IMBE) (X989 VSELP)
ADD ADD SPECTRA-TAC CONSOLE PRIORITY (X269) INTERFACE (C115) (Includes 8-Wire Capability)
6809 TRUNKING
(WIDE AREA ANALOG)
7-47
7-48
OPTIONAL SOFTWARE FEATURES STANDARD SOFTWARE FEATURES Basic TRC Battery Revert * 12.5 kHz Channels 5 MHz/10 MHz Ext. Reference Software Downloading Capability UHSO * Failsoft 8-Wire Capability * WildCard Capability ASTRO CAI 3.0 Remote RSS; includes: Station Password Protection Remote Dial-Up Capability * SMARTZONE 2.0.3 SMARTZONE 3.0 SMARTNET 2.0.2 SMARTNET 3.0 * = requires optional hardware
STATIONS SUPPORTED
Quantar
UHF R1/R2, 25 W; R1/R2, 110 W; R3, 110 W; R4, 100 W
6809 TRUNKING 6809 TRUNKING (SINGLE SITE SECURENET ) (X996) (X997) 6809 ASTRO TRUNKING (SINGLE SITE ASTRO ) (X992 VSELP)
SMARTZONE 6809 ASTRO TRUNKING (WIDE AREA ASTRO ) X897 IMBE) (X989 VSELP) ADD GPS SIMULCAST (X888)
(SINGLE SITE ANALOG)
ADD SPECTRA-TAC (X269) ADD CONSOLE PRIORITY INTERFACE (C115) (Includes 8-Wire Capability) ADD ANALOG SIMULCAST (X777) (Includes X269) ADD SPECTRA-TAC (X269)
(Requires X889 V.24 Board)
6809 TRUNKING
(WIDE AREA ANALOG)
688 1085E 35-AN
0 6/30 /201 1
STATIONS SUPPORTED
OPTIONAL SOFTWARE FEATURES

STANDARD SOFTWARE FEATURES Basic TRC
UHSO *
Failsoft 8-Wire Capability * WildCard Capability
68 8 10 85 E3 5 -A N
Battery Revert * 12.5 kHz Channels
5 MHz/10 MHz Ext. Reference
Quantar
UHF R1/R2, 25 W; R1/R2, 110 W;
R3, 110 W; R4, 100 W
Figure 7-28 Release R09.05.00/R09.06.00/R09.07.00/R10.00.00 through R10.08.00, R10.11.00, R10.12.00 Features and System Capabilities - 6809 Trunking
ASTRO CAI 3.0 Remote RSS; includes:
Station Password Protection Remote Dial-Up Capability * SMARTZONE 2.0.3 SMARTZONE 3.0
06 / 30 / 20 11
SMARTNET 2.0.2
Software Downloading Capability
6809 TRUNKING (SINGLE SITE ANALOG) 6809 TRUNKING (SINGLE SITE SECURENET ) (X996) (X997)
SMARTNET 3.0
SMARTZONE 6809 ASTRO TRUNKING
6809 ASTRO TRUNKING (SINGLE SITE ASTRO ) (X992 VSELP)
ADD SPECTRA-TAC (X269) ADD ANALOG SIMULCAST (X777) (Includes X269) ADD SPECTRA-TAC (X269)
(WIDE AREA ASTRO ) X897 IMBE) (X989 VSELP)
ADD CONSOLE PRIORITY INTERFACE (C115) (Includes 8-Wire Capability)
6809 TRUNKING
(WIDE AREA ANALOG)
ADD GPS SIMULCAST (X888) 6809 TRUNKING SIMULCAST (WIDE AREA SECURENET ) (Requires X889 V.24 Board)
7-49
7-50
STANDARD SOFTWARE FEATURES Basic TRC Battery Revert * 12.5 kHz Channels 5 MHz/10 MHz Ext. Reference Software Downloading Capability
STATIONS SUPPORTED
6809 TRUNKING SMARTZONE (SINGLE SITE ANALOG) (X997) (SINGLE SITE ASTRO ) (X992 VSELP) 6809 ASTRO TRUNKING (WIDE AREA ASTRO ) X897 IMBE) (X989 VSELP) 6809 ASTRO TRUNKING
OPTIONAL SOFTWARE FEATURES UHSO * Failsoft 8-Wire Capability * WildCard Capability ASTRO CAI 3.0 Remote RSS; includes: Station Password Protection Remote Dial-Up Capability * SMARTZONE 3.0/3.5/4.1 SMARTNET 3.0
ADD CONSOLE PRIORITY INTERFACE (C115) (Includes 8-Wire Capability) ADD ANALOG SIMULCAST (X777) (Includes X269)
6809 TRUNKING
(WIDE AREA ANALOG)
Figure 7-29 Release R12.01.00 through R12.03.00 Features and System Capabilities - 6809 Trunking
6809 TRUNKING SIMULCAST (WIDE AREA ANALOG) 6809 TRUNKING (WIDE AREAASTRO ) 6809 ASTRO TRUNKING SIMULCAST (WIDE AREA ASTRO)
688 1085E 35-AN
0 6/30 /201 1
STATIONS SUPPORTED
68 8 10 85 E3 5 -A N STANDARD SOFTWARE FEATURES Basic TRC Battery Revert * 12.5 kHz Channels 5 MHz/10 MHz Ext. Reference Software Downloading Capability
Quantar
UHF R1/R2, 25 W; R1/R2, 110 W; R3, 110 W; R4, 100 W
Figure 7-30 Release R13.00.00 through R14.00.00 Features and System Capabilities - 6809 Trunking
06 / 30 / 20 11
6809 TRUNKING (SINGLE SITE ANALOG) (X997) (SINGLE SITE ASTRO ) (X992 VSELP) 6809 ASTRO TRUNKING
SMARTZONE 6809 ASTRO TRUNKING (WIDE AREA ASTRO ) X897 IMBE) (X989 VSELP)
OPTIONAL SOFTWARE FEATURES UHSO * Failsoft 8-Wire Capability * WildCard Capability ASTRO CAI 3.0 Remote RSS; includes: Station Password Protection Remote Dial-Up Capability * SMARTZONE 3.0/3.5/4.1 SMARTNET 3.0
ADD SPECTRA-TAC (X269) ADD CONSOLE PRIORITY INTERFACE (C115) (Includes 8-Wire Capability) ADD ANALOG SIMULCAST (X777) (Includes X269) 6809 TRUNKING (SINGLE SITE ANALOG W/ CPI)
6809 TRUNKING
(WIDE AREA ANALOG)
6809 TRUNKING SIMULCAST (WIDE AREA ANALOG) 6809 TRUNKING (WIDE AREAASTRO ) 6809 ASTRO TRUNKING SIMULCAST (WIDE AREA ASTRO)
7-51
STATIONS SUPPORTED Quantro 800 MHz Quantar VHF R1 and R2 Quantro UHF R1 through R3 Quantar 900 MHz Quantro 350W VHF R1 and R2
INTELLIREPEATER TRUNKING (WIDE AREA ANALOG) (X999)
STANDARD SOFTWARE FEATURES Battery Revert * 12.5 kHz Channels 5 MHZ External Reference * = requires optional hardware
Figure 7-31 Release SZ2.0 Features and System Capabilities - IntelliRepeater Trunking
STATIONS SUPPORTED Quantro 800 MHz Quantar VHF R1 and R2 Quantro UHF R1 through R4 Quantar 900 MHz Quantro 350 W VHF R1 and R2
INTELLIREPEATER TRUNKING (WIDE AREA SECURENET ) (X998)

Battery Revert * 12.5 kHz Channels 5 MHZ External Reference * = requires optional hardware
Figure 7-32 Release SZ2.3 Features and System Capabilities - IntelliRepeater Trunking
STATIONS SUPPORTED Quantro Quantar Quantar Quantro Quantar Quantar 800 MHz 800 MHz VHF R1 and R2
INTELLIREPEATER TRUNKING (WIDE AREA SECURENET ) (X998)
Battery Revert * 12.5 kHz Channels 5/10 MHz External Reference UHSO * Full/Sub Band Partition OPTIONAL SOFTWARE FEATURES Remote RSS; includes: Station Password Protection Remote Dial-Up Capability * * = requires optional hardware
UHF R1 through R4 UHF R1, 25W; R2, 110 W; R4, 100 W 900 MHz
Figure 7-33 Release SZ2.7/2.7E Features and System Capabilities - IntelliRepeater Trunking
7-52
688 1085E 35-AN
0 6/30 /201 1
STATIONS SUPPORTED Quantro Quantar Quantar Quantro Quantar 800 MHz 800 MHz VHF R1 and R2 UHF R1 through R4 UHF R1/R2, 25 W; R1/R2, 110W ; R3, 110 W; R4, 100 W 900 MHz
OPTIONAL SOFTWARE FEATURES Remote RSS; includes: Station Password Protection Remote Dial-Up Capability *
Battery Revert * 12.5 kHz Channels 5/10 MHz External Reference UHSO * Full/Sub Band Partition
Quantar
SMARTZONE INTELLIREPEATER TRUNKING (WIDE AREA ANALOG) (X999)
SMARTZONE INTELLIREPEATER TRUNKING (WIDE AREA SECURENET ) (X998)
SMARTZONE ASTRO INTELLIREPEATER TRUNKING (WIDE AREA ASTRO ) (X990)
Figure 7-34 Release 12.00.00 through 12.02.00 Features and System Capabilities - IntelliRepeater SZ2.0.3 Trunking
STATIONS SUPPORTED Quantro Quantar Quantar Quantro Quantar 800 MHz 800 MHz VHF R1 and R2 UHF R1 through R4 UHF R1/R2, 25 W; R1/R2, 110 W; R3, 110 W; R4, 100W 900 MHz 900 MHz Battery Revert * 12.5 kHz Channels 5/10 MHz External Reference UHSO * Full/Sub Band Partition ASTRO CAI * = requires optional hardware SOFTWARE FEATURES SOFTWARE FEATURES Remote RSS; includes: Station Password Protection Remote Dial-Up Capability * SMARTZONE 3.0/3.5/4.1
Quantar Quantro
SMARTZONE INTELLIREPEATER TRUNKING (WIDE AREA SECURENET ) (X998) Note SECURENET is not supported beginning 1/1/02.
SMARTZONE ASTRO CAI INTELLIREPEATER TRUNKING (WIDE AREA ASTRO CAI ) (X898)
Figure 7-35 Release 12.00.00 through 12.02.00 Features and System Capabilities - IntelliRepeater SmartZone 3.0/3.5/4.1 Trunking
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
7-53
STATIONS SUPPORTED Quantro Quantar Quantar 800 MHz 800 MHz VHF R1 and R2
SOFTWARE FEATURES
SOFTWARE FEATURES Remote RSS; includes: Station Password Protection Remote Dial-Up Capability * SMARTZONE 3.0/3.5/4.1
Battery Revert * 12.5 kHz Channels 5/10 MHz External Reference UHSO * Full/Sub Band Partition ASTRO CAI
Quantro HF R1 through R4 U Quantar UHF R1/R2, 25 W; R1/R2, 110 W; R3, 110 W; R4, 100 W 900 MHz 900 MHz
Quantar Quantro
Figure 7-36 Release 13.00.00 through 13.02.00 Features and System Capabilities - IntelliRepeater SmartZone 3.0/3.5/4.1 Trunking
STATIONS SUPPORTED Quantro Quantar Quantar Quantro Quantar 800 MHz 800 MHz VHF R1 and R2 UHF R1 through R4 UHF R1/R2, 25 W; R1/R2, 110 W; R3, 110 W; R4, 100 W 900 MHz 900 MHz 350 W VHF R1 and R2 Battery Revert * 12.5 kHz Channels 5/10 MHz External Reference UHSO * Full/Sub Band Partition ASTRO CAI * = requires optional hardware SOFTWARE FEATURES SOFTWARE FEATURES Remote RSS; includes: Station Password Protection Remote Dial-Up Capability * SMARTZONE 3.0/3.5/4.1
Quantar Quantro Quantro
Figure 7-37 Release 14.00.00 Features and System Capabilities - IntelliRepeater SmartZone 3.0/3.5/4.1Trunking
STATIONS SUPPORTED Quantro Quantar Quantar Quantro Quantar 800 MHz 800 MHz VHF R1 and R2 UHF R1 through R4 UHF R1/R2, 25 W; R0/R1/R2, 110 W; R3, 110 W; R4, 100 W 900 MHz 900 MHz 350 W VHF R1 and R2 Battery Revert * 12.5 kHz Channels 5/10 MHz External Reference UHSO * Full/Sub Band Partition ASTRO CAI * = requires optional hardware SOFTWARE FEATURES SOFTWARE FEATURES Remote RSS; includes: Station Password Protection Remote Dial-Up Capability * SMARTZONE 3.0/3.5/4.1
Quantar Quantro Quantro
Figure 7-38 Release 14.02.00 Features and System Capabilities - IntelliRepeater SmartZone 3.0/3.5/4.1Trunking
7-54
688 1085E 35-AN
0 6/30 /201 1
STATIONS SUPPORTED Quantro 800 MHz Quantar 800 MHz Quantar VHF R1 and R2 Quantro UHF R1 through R4
OPTIONAL SOFTWARE FEATURES Remote RSS; includes: Station Password Protection Remote Dial-Up Capability *
Battery Revert * 12.5 kHz Channels 5/10 MHz External Reference UHSO * Full/Sub Band Partition 800 MHz Rebanding
Quantar UHF R1/R2, 25 W; R1/R2, 110 W; R3, 110 W; R4, 100 W Quantar 900 MHz Quantro 350 W VHF R1 and R2
SMARTZONE INTELLIREPEATER TRUNKING (WIDE AREA SECURENET ) (X998)
SMARTZONE ASTRO INTELLIREPEATER TRUNKING (WIDE AREA ASTRO ) (X990)
Figure 7-39 Release 14.00.00 Features and System Capabilities - IntelliRepeater SmartZone 2.0.3 Trunking
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
7-55
7-56
688 1085E 35-AN
0 6/30 /201 1
CHAPTER
Password Protection
...................................
QUANTAR and Quantro stations are equipped with a password protection feature that limits RSS access to the station by unauthorized personnel. Stations that are password protected prohibit any RSS action requiring communications with the station until the station password is entered.
How Password Protection Works ...................................

On a station with password protection activated, any attempted RSS action that requires communication with the station, such as reading the station codeplug, results in a password popup that prompts you to enter the station password. When the correct password is entered, the current RSS session may proceed until the session is terminated by the user, or until the station is reset. The next RSS session requires the password to be entered.
.... ..
Password Time-out
If the RSS remains idle for 10 minutes without user activity, an internal station timer expires, requiring the user to re-enter the password. You may bypass the password for the current RSS session by performing the procedure Bypassing the Station Password on page 8-6.
Activating Password Protection

Stations are shipped from the factory without a default password, and can therefore be accessed by any user with a compatible release of RSS software. To activate password protection, you must access Tools then Set device password and establish an initial password.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
8-1
CREATING THE STATIONS PASSWORD
CHAPTER 8: PASSWORD PROTECTION
Special Password Protection Features

The password protection feature allows a forgotten password to be erased, as well as temporary circumvention of the current password, leaving the current password valid. These features are described in this chapter.
Creating the Stations Password ...................................

To create a station password (for stations with either no prior password or an erased password), perform the procedure below:
1. 2. 3.
..
Connect the RSS computer to the station. Launch RSS and connect to the station. From the Tools menu, select Set device password. The Set Device Password window appears. Leave the Enter Current Password field blank (it currently has no password). Enter the new password in the Enter New Password field. Enter the new password in the Confirm New Password field. Click OK. If the passwords entered in the Enter New Password and Confirm New Password fields match, then the new password is saved. If the passwords do not match, the following warning window appears and you must re-enter the new password.
4. 5. 6. 7.
8-2
688 1085E 35-AN
0 6/30 /201 1
CHANGING STATION PASSWORD
Changing Station Password ...................................

To change an existing station password, perform the procedure below:
1. 2. 3.
..
Connect the RSS computer to the station. Launch RSS and connect to the station. From the Tools menu, select Set device password. The Station Password Prompt window appears.
4. 5.
Enter the current password. Click OK. The Set Device Password window appears.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
8-3
ERASING STATION PASSWORD (LOCAL ACCESS)
6. 7. 8. 9.
Enter the current password in the Enter Current Password field. Enter the new password in the Enter New Password field. Enter the new password in the Confirm New Password field. Click OK. If the passwords entered in the Enter New Password and Confirm New Password fields match, then the new password is saved. If the passwords do not match, the following warning window appears and you must re-enter the new password.
Erasing Station Password (Local Access) ................................... ..
NOTE
If the password is erased, all future RSS sessions (local or remote) are allowed without requiring a password. You may create another password by following the instructions on page Creating the Stations Password on page 8-2. If you wish to erase the current station password, if for example you have forgotten it, and are physically at the station site, perform the procedure below:
1. 2. 3.
Connect the RSS computer to the station. Launch RSS and connect to the station. From the Tools menu, select Set device password. The Station Password Prompt window appears.
4.
Type lost in the Enter Station Password field.
8-4
688 1085E 35-AN
0 6/30 /201 1
ERASING STATION PASSWORD (REMOTE ACCESS)
5.
Press and hold the Vol Up and Vol Down pushbuttons on the Station Control front panel. While holding the pushbuttons in, click OK on the Station Password Prompt window. The station password is permanently erased.
Erasing Station Password (Remote Access) ................................... ..
NOTE
If the password is erased, all future RSS sessions (local or remote) are allowed without requiring a password. You may create another password by following the instructions on page Creating the Stations Password on page 8-2. If you know the station password and are connected to the station through a remote dial-up connection, you may erase the current station password by performing the procedure below:
1. 2. 3.
Connect the RSS computer to a modem. Launch RSS and dial in to the station. From the Tools menu, select Set device password. The Station Password Prompt window appears.
4. 5.
Enter the current password. Click OK. The Set Device Password window appears.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
8-5
BYPASSING THE STATION PASSWORD
6. 7.
Type the current password in the Enter Current Password field. Do not enter a password. Instead, click OK. the RSS information window appears indicating that password protection has been disabled.
8.
Click OK to close the window.
Bypassing the Station Password ...................................

If you wish to temporarily bypass the station password, perform the procedures below. After the password has been bypassed, the current RSS session allows the RSS to operate as if you had entered the station password. When the RSS session is terminated, or the station is reset, password protection is again activated using the current password.
..
NOTE
You need not know the current station password to perform this procedure. However, you must be physically at the station site.
1. 2. 3.
Connect the RSS computer to a modem. Launch RSS and connect to the station. From the Tools menu, select Set device password. The Station Password Prompt window appears.
4.
Type service in the Enter Station Password field.
8-6
688 1085E 35-AN
0 6/30 /201 1
5.
Press and hold the Vol Up and Vol Down pushbuttons on the station control front panel. While holding the pushbuttons in, click OK. The station password is bypassed. The RSS operates as if you had entered the current station password.
NOTE
The time-out feature is still operational; if the 10 minute timer expires, you must repeat the password bypass procedure.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
8-7
8-8
688 1085E 35-AN
0 6/30 /201 1
CHAPTER
Remote Dial-Up
...................................
QUANTAR and Quantro stations support remote dial-up capability. This feature allows the service technician to make a dial-up connection through a modem to a station and perform RSS tasks. See Figure 9-1 for an example of a typical dial-up connection between a PC and a remotely located station.
....
NOTE
See the modem manufacturers instructions for information connecting the modem to your computer.
RS-232 Phone line RS-232
Station Station modem
PC modem
Laptop with RSS
Figure 9-1 Remote Dial-Up Connection
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
9-1
MODEM REQUIREMENTS
CHAPTER 9: REMOTE DIAL-UP
Modem Requirements ...................................

Two modems are required for a dial-up connection. One modem should have been installed at the stations location and is part of the system. The other modem is connected between your RSS PC and the land line. Although the figure shows a stand-alone modem, this modem can be installed in the laptop. If the modem is part of the RSS PC, the modems drivers and communications program (such as Hyperterminal) must be installed on the PC and the operating system set up properly for modem operation. See the documentation accompanying the modem and the operating systems documentation for information on installing and configuring the modem. Listed below are the requirements for modems for use with QUANTAR and Quantro stations: Hayes-compatible computer interface V.32 (9600 bps) protocol If error correction and/or data compression are desired, all connected modems must employ the same scheme Station modem must be configured for auto-answer
Station Modem Configuration ...................................

The station must be configured with the proper settings to allow communications with the PC modem. Configuration requires that a PC running a communications program be connected to the modem and commands be entered to program the desired settings. The following procedure provides the configuration for the communications program that is to control the modem:
1. 2.
Temporarily connect the stations modem to the RSS PC. Launch the communications program (such as ProComm or Hyperterminal). See the programs manual or help file if required. Enter the following command to program the modem settings for the factory defaults: AT&F<return>
.. ..
3.
4.
Enter the following command string to program the modem for the recommended configuration settings: ATE0Q1&D0&K0N0S37=9S0=1<return> Where: AT: Attention E0: Character echoing disabled
9-2
688 1085E 35-AN
0 6/30 /201 1
PC MODEM CONFIGURATION

5.
Q1: Result code transmission disabled &D0: Ignore DTR &K0: XON/XOFF disabled (RTS/CTS) disabled N0S37=9S0=1: 9600 bps connections only S0=1: Auto-answer after 1 ring
Enter AT&W0&Y0<return> command to store the configuration settings in modem memory and to instruct the modem to load these settings on modem power up.
PC Modem Configuration ...................................

Programming the configuration settings for the PC modem is accomplished using the RSS program (release 5.00 or higher). The RSS provides a modem configuration screen that includes an initialization string sent to the PC modem on initiation of a remote session with a station. This string programs the PC modem for proper operation. The screen also contains additional fields to allow related modem configuration parameters to be programmed. To configure the PCs modem through the RSS Modem Configuration screen, perform the following procedure:
1. 2.
..
Launch the RSS program. From the Tools menu, select Configure Connection. The Configure Connection window appears. Click Modem.
3.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
9-3
The screen changes to provide modem configuration controls.

4.
Click Phone Book. The Phone Book window appears.
5.
Enter the dial-up phone numbers for the sites where the stations are installed and provide an obvious description for each number, such as the site identifier. Click Save when done.
6.
9-4
688 1085E 35-AN
0 6/30 /201 1
7.
Click Modem Configuration. The Modem Configuration window appears.
8.
Configure the fields in this window as required. See Table 9-1.
Table 9-1 RSS PC Modem Configuration Data Fields Data Fields Description Valid Range/ Selections Command Strings Initialization Command string sent to PC modem on initiating a remote dial-up connection. N/A ATE1Q0V1X4&K0S 0=0^M Default command string designed for most Hayes compatible modems. If default fails, try modem factory settings (AT&F^M), or refer to modem user guide. System dependent Default Recommended Setting (if any)
Dial Prefix
Specifies the dialing method (pulse or tone).
ATDT: Tone dialing ATDP: Pulse dialing
ATDT
Dial Suffix
Specifies the character that signifies the end of the dialing string. Specifies the command string sent to hang up the modem.
^M: Carriage return N/A
^M
System dependent
Hang-up
+++~ ~ ~ ATH0^M
Default is Hayes compatible
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
9-5
Table 9-1 RSS PC Modem Configuration Data Fields (continued) Data Fields Drop DTR to hang-up Wait for Connect Description Specifies whether modem pulls RS-232 DTR line low when hanging up. Specifies the maximum length of time modem attempts to successfully connect to a remote modem before RSS hangs up and retries (see Pause between Calls). Specifies the amount of time before RSS redials after an unsuccessful connection attempt. Valid Range/ Selections Enabled Disabled 1 to 999 seconds 60 seconds Determined by user. Ensure value is less than time to wait for carrier after dial S register setting (internal to modem). Refer to the modem user guide. Determined by user Default Enabled Recommended Setting (if any) System dependent
Pause between CAlls
1 to 999 seconds
5 seconds
Modem Response Strings for Connect Specifies the key word in modem status message that indicates a successful connection. Specifies the key word in modem status message that indicates called modem phone is busy. Specifies the key word in modem status message that indicates no carrier signal from called modem. N/A Connect Default is Hayes compatible. Otherwise, refer to modem user guide. Default is Hayes compatible. Otherwise, refer to modem user guide. Default is Hayes compatible. Otherwise, refer to modem user guide.
Busy
N/A
Busy
Failure
N/A
No Carrier
9-6
688 1085E 35-AN
0 6/30 /201 1
Table 9-1 RSS PC Modem Configuration Data Fields (continued) Data Fields Failure Description Specifies the key word in modem status message that indicates no dial tone on phone line. Specifies the key word in modem status message that indicates some form of communications error has occurred. Specifies the key word in modem status message that indicates exceeded time-out threshold (internal to modem) occurred between dialing and carrier detect. Valid Range/ Selections N/A Default No Dialtone Recommended Setting (if any) Default is Hayes compatible. Otherwise, refer to modem user guide. Default is Hayes compatible. Otherwise, refer to modem user guide.
Failure
N/A
Error
Failure
N/A
Time-out
Default is Hayes compatible. Otherwise, refer to modem user guide.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
9-7
9-8
688 1085E 35-AN
0 6/30 /201 1
WildCard Operation
10
10
CHAPTER
...................................
This chapter describes the operation of the WildCard option and how to make the various settings to implement custom WildCard functions. The WildCard option is a purchasable option that can be enabled on any QUANTAR or Quantro station or QUANTAR or ASTRO-TAC receiver. The WildCard option provides a powerful, user-friendly tool that is used to initiate specific functions whenever certain specific conditions are met. The relationship between the function that is executed and the conditions that initiate it is specified in the WildCard Action Table, which contains two sections: One specifies the conditions One specifies the function or action to execute
The section that contains the conditions allows the programmer to specify up to three states/ inputs and two Boolean functions that tie the states/input together and to determine the functions to execute. The station continuously evaluates the states and inputs specified using the Boolean operators to determine when the condition, as evaluated through the Boolean logic statement, is true or false. When the condition becomes true, the commands specified in the Action Table are executed in sequential order. When the condition becomes false, the commands specified in the Inaction Table are executed in sequential order. Commands are executed only when conditions change. If conditions do not change, commands are not executed. WildCard functions may be created to provide simple monitoring tasks, such as causing the station to generate a tone over the wireline when Battery Revert becomes true, to complex tasks, such as the Main/Standby feature which requires multiple tables to implement. In general, using the WildCard option is comprised of the following three major steps:
1.
....
Configure station auxiliary inputs Configure inputs into binary groups for external channel or access code table control Configure individual inputs Configure station auxiliary outputs Configure outputs into binary groups for reporting of station channel, MCS user information, or access code table control Configure individual outputs Configure state/action tables Modify default state/action tables to accommodate unique system requirements Generate new state/action tables to implement new WildCard functions
2.
3.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
10-1
STATION AUXILIARY INPUTS
CHAPTER 10: WILDCARD OPERATION
Station Auxiliary Inputs ...................................

Each QUANTAR and Quantro station and QUANTAR Receiver contains circuitry located on the wireline interface board that can accept TTL inputs and relay closures (AUX Inputs) from miscellaneous external equipment. Two types of inputs are provided: Opto-coupled Transistor
These are available through the 50-pin system connector located on the station backplane. For normal operation (without WildCard option), many of these inputs have predefined functions, as described in the Backplane section of the appropriate QUANTAR or Quantro Station Functional Manual or QUANTAR Receiver Functional Manual. However, with the WildCard Option available and enabled through the RSS, the function of each predefined input and each undefined input, may be customized, usually to implement one or more WildCard functions. An additional feature is the ability to select predefined combinations of inputs (binary groups). When used with a properly programmed WildCard Function, this feature facilitates binary control of the station by an external source, such as the console, to control the station operating channel or select an Access Code Table. For example, Binary Group 1 is comprised of station inputs 1, 2, 3, and 4, and may be used to allow the station operating channel to be set according to the binary state of the four inputs, for example 0010 sets the station to Channel 2.
..
Programming the WildCard Input Screen
A common application of the station inputs is allowing external equipment, usually a console, to control the current station channel number and/or the access code table number to be used by the station. To facilitate these applications, the WildCard Input screen provides the ability to select predefined groups of inputs whose binary values determine the station channel or access code table. Alternatively, in order to provide maximum flexibility in designing WildCard Functions, the inputs may also be configured individually. To access the WildCard Input screen, click WildCard Input in the navigation pane. Figure 10-1 shows representative WildCard screens (Enhanced selected in the Hardware Configuration screen). The figure shows two views: one where the Binary Groups are set to None and the other when inputs are specified. Table 10-1 provides descriptions of the provided fields.
10-2
688 1085E 35-AN
0 6/30 /201 1
STATION AUXILIARY INPUTS
Figure 10-1 WildCard Input Screen - Enhanced Shown Table 10-1 WildCard Input Screen Data Fields Data Field Channel Binary Group Description Used to select one (or None) of the predefined binary groups used to select Access Code Table (overriding ACT programmed for channel in Channel Information screen). Used to select one (or None) of the predefined binary groups used to control station operating channel. Range/Selections None 1 (Inputs 1-4) 2 (Inputs 1-8) 3 (Inputs 9-10) 4 (Inputs 9-12) 5 (Inputs 5-8) None Default Recommended Setting (if any) System dependent
Access Code Table Binary Group
None 1 (Inputs 1-4) 2 (Inputs 1-8) 3 (Inputs 9-10) 4 (Inputs 9-12) 5 (Inputs 5-8)
None
System dependent
Active Level
If a binary group is selected, active level (HI or LO) is chosen here; applies to all inputs of selected binary group. Station Aux Inputs listed here; correspond to AUX IN 1-12 inputs shown for 50-pin System Connector in Backplane section of appropriate QUANTAR or Quantro Station Functional Manual, or example AUX IN 7.
Hi Lo
N/A
System dependent
Aux Input
1-12 for enhanced 1-9 for basic
N/A
Dependent on whether basic or enhanced WildCard is selected
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
10-3
STATION AUXILIARY OUTPUTS
Table 10-1 WildCard Input Screen Data Fields (continued) Data Field HW Input Type Description Specifies hardware circuitry (located on Wireline Interface Board) associated with input. Range/Selections Basic and Enhanced: 1-8: Transistor Basic: 9: Opto-coupler Enhanced: 9-12: Opto-coupler Transistor: Hi/Lo Opto-coupler: Hi/Lo Default Basic and Enhanced: 1-8: Transistor Basic: 9: Opto-coupler Enhanced: 9-12: Opto-coupler Transistor: Lo Opto-coupler: Hi Recommended Setting (if any) Dependent on whether basic or enhanced WildCard is selected.
Active Level
Indicates current active level for each input; may be set for HI or LO. Defines binary bit ranking for binary groups. Bit 0 is LSB and Bit 3 is MSB.
System dependent
Group Definition
Station Auxiliary Outputs ...................................

Each QUANTAR and Quantro station and QUANTAR Receiver contains circuitry located on the wireline interface board that provides auxiliary outputs (AUX Outputs) to control miscellaneous external equipment. Two types of outputs are provided: Transistor Relay closure
These are available through the 50-pin System Connector located on the station backplane. For normal operation (without WildCard Option), many of these outputs have pre-defined functions, as described in the Backplane section of the appropriate QUANTAR or Quantro Station Functional Manual. However, with the WildCard Option available and enabled through the RSS, the function of each pre-defined output, as well as each undefined output, may be customized (usually to implement one or more WildCard Functions). An additional feature is the ability to select pre-defined combinations of outputs (binary groups). When used with a properly programmed WildCard Function, this feature allows the station to report to external equipment (such as a console), the current station operating channel, Access Code Table, or MCS user. For example, Binary Group 1 is comprised of station outputs 1, 2, 3, and 4, and may be used to allow the station to report the current operating channel to external equipment, such as a console. For example, 0010 reports that the station is currently operating on Channel 2.
..
10-4
688 1085E 35-AN
0 6/30 /201 1
STATION AUXILIARY OUTPUTS
Programming the Wildcard Output Screen

This screen is available when the WildCard Option is set to either Basic or Enhanced on the Hardware Configuration screen. To access the WildCard Output screen, click WildCard Output in the navigation pane, see Figure 10-2. See Table 10-2 for the screens data fields.
Figure 10-2 WildCard Output Screen - Enhanced Shown Table 10-2 WildCard Output Screen Data Fields Data Field
Channel Binary Group
Description
Used to select one (or None) of the pre-defined binary groups used to report station operating channel.
Range/Selections
None 1 (Inputs 1-4) 2 (Inputs 1-8) 3 (Inputs 9-10) 4 (Inputs 9-12) 5 (Inputs 5-8) None 1 (Inputs 1-4) 2 (Inputs 1-8) 3 (Inputs 9-10) 4 (Inputs 9-12) 5 (Inputs 5-8) None 1 (Inputs 1-4) 2 (Inputs 1-8) 3 (Inputs 9-10) 4 (Inputs 9-12) 5 (Inputs 5-8) None
Default

System dependent
Multi Code Squelch Table Binary Group
Used to select one (or None) of the pre-defined binary groups used to report MCS users.
None
System dependent
Access Code Table Binary Group
Used to select one (or None) of the pre-defined binary groups used to report Access Code Table.
None
System dependent
Aux Output
Station Aux Outputs listed here; correspond to AUX OUT (#) outputs shown for 50-pin System Connector in backplane section of appropriate QUANTAR or Quantro Station Functional Manual (for example, AUX OUT 7).
1-12 for enhanced 1-9 for basic
N/A
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
10-5
STATE/ACTION TABLES
Table 10-2 WildCard Output Screen Data Fields (continued) Data Field
HW Input Type
Description
Specifies hardware circuitry (located on wireline interface board) associated with output.
Range/Selections Basic and Enhanced: 1-3: Transistor Basic: 7: Relay Enhanced: 7-10: Relay
Hi Lo
Default Basic and Enhanced: 1-3: Transistor Basic: 7: Relay Enhanced: 7-10: Relay Transistor: Lo Relay: Lo

Active Level
Indicates current active level for each output; may be set for HI or LO. Defines binary bit ranking for binary groups. Bit 0 is LSB and Bit 1 is MSB.
System dependent
Group Definition
State/Action Tables ...................................

The State/Action Tables screen(s) provides a powerful interface that allows custom WildCard functions to be created or existing WildCard Functions to be modified. Implementing WildCard functions using the State/Action Tables ranges from simple single action tables to complex multiple action tables. A common application of the station outputs is to provide external monitoring equipment with indications of the current station channel, Access Code Table, and/or MCS users. To facilitate these applications, the Output Configuration screen provides the ability to select pre-defined groups of outputs whose binary values indicate the station channel, access code table, or MCS users. Alternatively, in order to provide maximum flexibility in designing WildCard functions, the outputs may also be configured individually. Three binary group programming areas are provided on the WildCard Input screen, one for Channel Binary Group, one for ACT Binary Group, and one for MCS Binary Group. These areas are used to program the pre-defined input combinations (binary group) which is used to indicate the external equipment of the channel, ACT, and/or MCS users. Each may be programmed independently.
..
10-6
688 1085E 35-AN
0 6/30 /201 1
STATE/ACTION TABLES
CAUTION
While the State/Action Tables feature provides a powerful, flexible method of creating and modifying WildCard Functions, there is also the increased risk of misprogramming which can result in infinite loops, inadvertently resetting the station, and other unintentional station behavior. Please exercise caution when defining the inputs and outputs, and when configuring the State/Action Tables.
IMPORTANT
If WildCard and SECURENET features are both enabled, Output 2 must remain active LO and cannot be used in any other WildCard table, either as an individual output or as part of a Binary Group.
How State/Action Tables Operate

Whenever a state changes from True to Untrue, the state/condition statement, in State and Condition Settings are evaluated from left to right with no parentheses. If the logical result changes from Untrue to True, the command(s) in the Action list is executed by the station. If the list contains more than one command, the commands are executed sequentially. All commands in the list are executed even if the logical result of the state/condition evaluation becomes untrue during performance of the sequence. If the result changes from true to untrue, the command(s) in the Inaction list is executed by the station. If the list contains more than one command, the commands are executed sequentially. All commands in the list are executed even if the logical result of the state/condition evaluation becomes true during performance of the sequence. The figure below shows a simple example: When Input 2 (TX Inhibit) becomes true (logic HI, as defined in the WildCard Input screen), the TX INHIBIT command in the Action list is executed by the station. The station transmitter is now inhibited and remains so until the condition becomes untrue (logic LO), at which time the command in the Inaction list is executed. The station transmitter is now enabled and remains so until the condition again becomes true.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
10-7
STATE/ACTION TABLES
Programming the Wildcard State Screen

This screen is available when the WildCard Option is set to either Basic or Enhanced on the Hardware Configuration screen. Each station equipped with the WildCard Option comes programmed with a default set of State/Action Tables that provide a basic set of station functions, such as Ext PTT, RX Code Det, or RD Stat. The default tables utilize the predefined functions assigned to the station auxiliary inputs and outputs, as described in the Backplane section of the appropriate QUANTAR or Quantro station or QUANTAR receiver Functional Manual. The number of default tables depends on the station type: conventional or 6809 trunking. You may use the default tables as provided, modify one or more to satisfy unique customer requirements, or add tables (thus adding WildCard functions). The Action and Inaction lists provide up to XX fields for entering commands.
IMPORTANT
It is important to remember that for any given state change, the command list in each and every State/Action Table containing the state change in the State/ Condition string is executed. Be very careful when designing WildCard functions to consider the impact of commands in a given State/Action Table with all other State/Action Tables, even tables that do not relate specifically to the same WildCard function. To access the WildCard State screen, click WildCard State in the navigation pane, see Figure 10-2. See Table 10-2 for the screens data fields.
Figure 10-3 WildCard State Screen
10-8
688 1085E 35-AN
0 6/30 /201 1
STATE/ACTION TABLES
Table 10-3 WildCard State/Action Screen Data Fields Data Field Description Description Indicates the name assigned to the WildCard Function implemented by this table. Enter text using keyboard (14 alphanumeric characters max). Indicates the current table number and shows total number of tables currently implemented. Enter desired table number and press Enter key to display corresponding table. Defines a station state that is used to determine an action. Determines the boolean operation performed on the selected states. Range/Selections Up to 15 alphanumeric characters Default Blank Recommended Setting (if any) System dependent
Table
Up to XX tables
System dependent
Jump to Table
Up to the number of configured tables Provided in selection list AND AND NOT OR OR NOT
System dependent
State Field Condition Field
Blank Blank
Action
Action list contains commands which are executed sequentially (top to bottom) when the state/condition settings change from untrue to true. Inaction list contains commands which are executed sequentially (top to bottom) when the state/condition settings change from true to untrue.
Provided in selection list
Blank
Inaction
Provided in selection list
Blank
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
10-9
STATE/ACTION TABLES
10-10
688 1085E 35-AN
0 6/30 /201 1
Software Downloading
11
11
CHAPTER
...................................
QUANTAR and Quantro stations, ASTRO-TAC comparators, and ASTRO-TAC receivers (equipped with FLASH memory) support the Software Download (SWDL) feature. This feature allows service personnel to download the station operating software (previously stored in firmware) directly to the station. The download may be performed either locally, through a null modem, or remotely, through a dial-up modem. The SWDL process differs from connecting to a device through RSS because SWDL requires the use of file transfer protocol (FTP) and RSS does not. Therefore, you must configure a modem to use serial line internet protocol (SLIP) because SLIP supports FTP. The process for performing a SWDL to upgrade your devices software is outlined below:
1. 2.
Ensure the prerequisites are met. See Prerequisites on page 11-2. Prepare the PC for connecting to the station, receiver, or comparator. See Preparing PC for Software Download Communications on page 11-3.
....
NOTE
Step 3 is needed only if your device is an IntelliRepeater and you are going to connect through an Ethernet connection or a zone controller link connection.
3.
Copy the device software from the Motorola-supplied disk to the PC hard disk. See Loading Station Software Files onto the PC on page 11-41. Connect to the device. See Connecting to the Device on page 11-35. Download the station software from the PC to the station: If your device is not an IntelliRepeater: See Downloading Software to Station/ Receiver Memory - Conventional and 6809 Controller Systems or ASTRO-TAC Comparator Memory on page 11-41. If your device is an IntelliRepeater: See Downloading Software to IntelliRepeater Memory on page 11-45.
4. 5.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
11-1
PREREQUISITES
CHAPTER 11: SOFTWARE DOWNLOADING
Prerequisites ...................................
Only QUANTAR and Quantro stations, ASTRO-TAC comparators, and ASTRO-TAC receivers that are equipped with FLASH memory allow software downloading. Verify that the Motorola model numbers for the station control board, wireline interface board, and wireline/power supply board are as follows. The model number is printed on an adhesive label on the component side of the board, along with a bar code as follows: QUANTAR/Quantro Stations: Station control board: IntelliRepeater: CLN6960 Conventional/6809: CLN6961 Data base station: CLN6962
..
Wireline interface board: 4-wire North America: CLN6955 8-wire North America: CLN6956 4-wire International: CLN6957 8-wire International: CLN6958
ASTRO-TAC Receivers: Wireline/power supply board: TTN5041 Station control board: CLN6873
ASTRO-TAC Comparator: Flash Capable Comparator Control Board: CLN7361 Flash Capable Wireline Board: CLN7343
NOTE
If your station/receiver is equipped with a model different than those listed above, the station operating software is contained in EPROMs, you may not use the Software Download feature unless the module has been upgraded with FLASH memory. Refer to FLASHport Upgrades Ordering Guide for details.
11-2
688 1085E 35-AN
0 6/30 /201 1
PREPARING PC FOR SOFTWARE DOWNLOAD COMMUNICATIONS
Preparing PC for Software Download Communications ...................................

The software download (SWDL) feature can be installed and run on the following Microsoft Windows operating systems: Windows XP Professional Windows Vista Windows 7
Configure your PC for connecting to the device depending on the Microsoft Windows operating system you are running and the method of serial communications you are using as outlined below: If connecting the PCs serial port directly to the stations RSS port: For Windows XP, see Adding a Null Modem Device in Microsoft Windows XP Professional on page 11-3. For Windows Vista and Windows 7, see Adding a Virtual Network Adapter Driver in Microsoft Windows Vista and Windows 7 on page 11-25.
..
If connecting through a dial-up modem: For Windows XP, see Adding a Dial-Up Modem Device in Microsoft Windows XP Professional on page 11-15. For Windows Vista and Windows 7, see Adding a Virtual Network Adapter Driver in Microsoft Windows Vista and Windows 7 on page 11-25.
Adding a Null Modem Device in Microsoft Windows XP Professional

To connect to the station or comparator to perform Software Download using a direct connection, you must:
1.
Add a null modem that uses your computers serial port. This is used to connect to the device. See Adding a Null Modem in Windows XP Professional on page 11-3. Add a SLIP connection that uses the null modem you just added. See Adding a SLIP Connection in Windows XP Professional for a Null Modem Connection on page 11-8.
2.
Adding a Null Modem in Windows XP Professional

To add a null modem to connect to the device, perform the following procedure:
1. 2. 3.
Open the Control Panel. Click Printers and Other Hardware. Click Phone and Modem Options.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
11-3
4.
On the window that appears, click the Modems tab.
5.
Click Add at the bottom of the screen. The following window appears.
6. 7.
Select Dont detect my modem; I will select it from a list check box. Click Next. The following window appears.
8. 9.
Click Have Disk. On the screen that appears, browse to the directory that contains the mdmmotcss9x.inf and mdmmotcssnt.inf files. Generally, these files are found in the default installation directory C:\Program Files\Motorola\Radio Service Software\SLIPdrv\XP. Click Open. The following window appears.
10.
11-4
688 1085E 35-AN
0 6/30 /201 1
11.
Select the following: Motorola CSS NT from the Manufacturers list. CSS SLIP Connection NT from the Models list.
12.
Click Next. The following window appears.
13.
Select the following: Click Selected ports. Select the PC port that you use to perform the serial software download to the device.
14.
Click Next. The following warning message appears.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
11-5
15.
Click Continue Anyway to disregard it. If the operation was successful, the following window appears.
16.
Click Finish to exit. The following window appears. This window now contains the modem connection you just added.
17.
Select your new connection.
11-6
688 1085E 35-AN
0 6/30 /201 1
18. 19.
Click Properties at the bottom. Select the Advanced tab.
20.
Click Change Default Preferences... at the bottom of the screen.
The following window appears.
21.
Select the following on the General tab: Flow control: None Port Speed: 38400
22.
Select the following on the Advanced tab: Data bits: 8 Parity: None Stop bits: 1
23.
Click OK on all open screens until you reach the control panel again.
You have successfully added a null modem that provides the means to connect to a station or comparator using a SLIP connection. Proceed with the following section to add a SLIP connection.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
11-7
Adding a SLIP Connection in Windows XP Professional for a Null Modem Connection

To add a SLIP connection in Windows XP perform the following procedure:
1.
Launch the Control Panel and click on the Network Connections icon.
The following menu appears.
2. 3.
Select New Connection from the File menu. When the next window appears, click Next. The following window appears.
11-8
688 1085E 35-AN
0 6/30 /201 1
4. 5.
Select Set up an advanced connection. Click Next. The following window appears.
6. 7.
Select Connect directly to another computer. Click Next. The following window appears.
8.
Select Guest, then click Next. The following window appears.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
11-9
9.
Enter the name of the connection in accordance with the rules provided in RSS SLIP Connection Naming Convention on page 11-34. Click Next. The following window appears.
10.
11. 12.
Select the device you just added from the dropdown box. Click Next. The following window appears.
13.
Select Anyones use, then click Next. The following window appears.
11-10
688 1085E 35-AN
0 6/30 /201 1
14.
Click Finish. The following window appears.
NOTE
Leave the area code and phone number fields blank.
15.
Click Properties. The following window appears.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
11-11
16.
Select the device you just added and then click Configure. The following window appears.
17.
Select the desired baud rate and uncheck all other checkboxes. You can only select baud rate values that are supported by RSS.
NOTE
See RSS SLIP Connection Naming Convention on page 11-34 for baud rate and connection name dependencies.
11-12
688 1085E 35-AN
0 6/30 /201 1
18.
Click OK. The following window appears. Select the Options tab and set the option selection as shown in the figure below.
19.
Select the Networking tab and set the option selection as shown in the figure below.
20. 21.
Select SLIP: Unix Connection in the Type of dial-up server I am calling: list Select the Internet Protocol (TCP/IP) entry.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
11-13
22.
23.
Set the IP Address field as follows, leaving the rest blank: If the connection being configured connects to the front port of the device, the IP should be 193.0.0.5 If the connection being configured connects to the back port of the device, the IP should be 193.0.0.4
24.
Click Advanced. The following window appears.
25. 26.
Uncheck the Use default gateway on remote network check box. Click OK on all windows until you reach the Network Connections screen. When you finish clicking OK on all windows, a Connect window appears, offering you the opportunity to connect to the device. Click Cancel to close the Connect window.
NOTE
You cannot connect to the device using the Connect window, a successful connection can only be made using the RSS.
11-14
688 1085E 35-AN
0 6/30 /201 1
You are now ready to perform the SWDL procedure to upgrade the devices software. See Serial (Direct) Connection on page 11-35.
Adding a Dial-Up Modem Device in Microsoft Windows XP Professional

To connect to the station or comparator to perform Software Download using a remote connection, you must:
1.
Add a dial-up modem that is used to connect to the device at a remote location. See Adding a Dial-Up Modem in Windows XP Professional on page 11-15. Add a SLIP connection that uses the modem you just added. See Adding a SLIP Connection in Windows XP Professional for a Dial-Up Modem Connection on page 11-17.
2.
Adding a Dial-Up Modem in Windows XP Professional

To add a dial-up modem to connect to the device from a remote location, install the dial-up modem in your computer in accordance with the installation instructions provided by the manufacturer. On completion of the new modems installation or for an existing modem, set up the dial-up modem as directed in the procedure below:
1.
If not already open, (it opens by default when adding a new modem) open the Modem Options window from Control Panel. The following window appears.
2. 3. 4.
Select the modem from the list. Click Properties at the bottom. Select the Advanced tab.
5.
Click Change Default Preferences... found at the bottom of the screen.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
11-15
6.
Select the following on the General tab: Flow control: None Port Speed: 38400
7.
Select the following on the Advanced tab: Data bits: 8 Parity: None Stop bits: 1
8.
Click OK on all open windows until you reach the control panel again.
You have successfully added a dial-up modem that provides the means to connect to a station or comparator using a SLIP connection from a remote location. Proceed with the following section to add a SLIP connection.
11-16
688 1085E 35-AN
0 6/30 /201 1
Adding a SLIP Connection in Windows XP Professional for a Dial-Up Modem Connection

To add a SLIP connection in Windows XP to connect to a device from a remote location, perform the following procedure:
1.
Open the Control Panel and double-click the Network Connections icon.
2.
On the window that appears, from the File menu, select New Connection.
3.
Click Next on the window that appears.
4. 5.
Select Connect to the Internet. Click Next. The following window appears.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
11-17
6. 7.
Select Set up my connection manually. Click Next. The New Connection Wizard window appears as shown in the example below.
8. 9.
Select the modem device that you use for this connection. Click Next. The following window appears.
11-18
688 1085E 35-AN
0 6/30 /201 1
10. 11.
Select Connect Using a dial-up modem. Click Next. The following window appears.
12.
Enter the name of the connection in accordance with the rules outlined in RSS SLIP Connection Naming Convention on page 11-34. Do not add any other text to the name other than what is stated in the rules. Click Next. The following window appears.
13.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
11-19
14.
Leave the phone number field blank and click Next. The following window appears.
15.
Select Anyones use, then click Next. The following window appears.
11-20
688 1085E 35-AN
0 6/30 /201 1
16. 17.
Leave all the fields blank and uncheck all checkboxes. Click Next. The following window appears.
18.
Click Finish. The following window appears.
NOTE
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
11-21
19.
NOTE
20.
Select the device you just added and then click Configure. The following window appears.
11-22
688 1085E 35-AN
0 6/30 /201 1
21.
Select the desired baud rate and uncheck all other check boxes. You can only select baud rate values that are supported by RSS.
NOTE
See RSS SLIP Connection Naming Convention on page 11-34 for baud rate and connection name dependencies.
22. 23.
Click OK. Select the Options tab and set the option selection as shown in the figure below.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
11-23
24.
Select the Networking tab. The following screen appears.
25. 26. 27.
Select SLIP: Unix Connection in the Type of dial-up server I am calling: list. Select the Internet Protocol (TCP/IP) entry. Click Properties. The following window appears.
11-24
688 1085E 35-AN
0 6/30 /201 1
28.
Set the IP Address field as follows, leaving the rest blank: If the connection being configured connects to the front port of the device, the IP should be 193.0.0.5 If the connection being configured connects to the back port of the device, the IP should be 193.0.0.4
29.
Click Advanced. The following window appears.
30. 31.
Uncheck the Use default gateway on remote network check box. Click OK on all windows until you reach the Network Connections screen. When you finish clicking OK on all windows, a Connect window appears offering you the opportunity to connect to the device. Click Cancel to close the Connect window.
NOTE
You cannot connect to the device using the Connect window, a successful connection can only be made using the RSS. You are now ready to perform the SWDL procedure to upgrade the devices software. See Remote Dial-Up Connections on page 11-38.
Adding a Virtual Network Adapter Driver in Microsoft Windows Vista and Windows 7
To connect to the station or comparator to perform Software Download using a direct or remote connection, you must add a Virtual Network Adapter that uses your computer's serial port. This is used to connect to the device. See Adding a Virtual Network Adapter Driver in Microsoft Windows Vista and Windows 7 on page 11-25.
Adding a Virtual Network Adapter Driver in Windows Vista and Windows 7

To add a Virtual Network Adapter driver to connect to the device, perform the following procedure:
1.
Open the Control Panel.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
11-25
2.
Click Device Manager. The following screen appears.
3.
Right-click on a computers name in a root of the tree and select Add legacy hardware. The following screen appears.
11-26
688 1085E 35-AN
0 6/30 /201 1
4.
Click Next. The following screen appears.
5.
Select Install the hardware that I manually select from a list and click Next. The following screen appears.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
11-27
6.
Select Network adapters and click Next. The following screen appears.
7.
Click Have Disk. The Install From Disk screen appears.
8.
Click Browse and navigate to the directory that contains the MotorolaVNDC.inf file. Generally, this file is found in the default installation directory: For Windows Vista: C:\Program Files\Motorola\Radio Service Software\SLIPdrv\Vista. For Windows 7 32 bits: C:\Program Files\Motorola\Radio Service Software\SLIPdrv\Win7. For Windows 7 64 bits: C:\Program Files (x86)\Motorola\Radio Service Software\SLIPdrv\Win7.
Select the MotorolaVNDC file and click Open. The Install From Disk window becomes active again.
11-28
688 1085E 35-AN
0 6/30 /201 1
9.
Click OK. The following screen appears.
10.
Select MotorolaVNDC adapter and click Next. The following screen appears.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
11-29
11.
Click Next. One of the following screens appears.
12.
Click Install. During the driver installation the following screen appears.
11-30
688 1085E 35-AN
0 6/30 /201 1
13.
The following completion window appears when the driver software has been successfully installed.
14. 15. 16.
Click Finish. Open the Control Panel. Click Network and Sharing Center. The following screen appears.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
11-31
17.
Click Manage network connections. The following screen appears.
18.
Right-click the icon for the network with the the MotorolaVNDC adapter, and then click Properties. The Network Connection Properties window appears.
11-32
688 1085E 35-AN
0 6/30 /201 1
RSS SLIP CONNECTION NAMING CONVENTION
19.
Select Internet Protocol Version 4 and deselect all other connections, then highlight Internet Protocol Version 4 and click Properties. The Internet Protocol Properties window appears.
20.
Select Obtain an IP address automatically and Obtain DNS server address automatically, then click OK. The Network Connection Properties window returns. Click OK. You are now ready to perform the SWDL procedure to upgrade the device's software. For direct connections, see Serial (Direct) Connection on page 11-35. For remote connections, see Remote Dial-Up Connections on page 11-38.
21.
RSS SLIP Connection Naming Convention ...................................

Due to the limitation of dynamic creation of a SLIP connection using the Windows Remote Access Service (RAS) module, a naming convention was created to allow the RSS to communicate with the Windows RAS through a null modem (serial cable).
..
NOTE
The CSS application uses the same connections for null modem (serial) SWDL, therefore the same naming is used for both applications.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
11-33
RSS SLIP CONNECTION NAMING CONVENTION
Naming Convention for Null Modem install

A Windows RSS SLIP connection name has three items that depend on and describe some physical parameters of the connection. A typical RSS SLIP connection name is CSS_SLIP_FP_9600_COM1, and breaks down as follows: CSS_SLIP: This part of the connection name is fixed. All RSS SLIP connections must start with this string. FP: This part of the name describes the device port the connection is capable of connecting with. Allowed strings are FP (front port) and BP (back port). 9600: This part of the name describes the baud rate at which the connection communicates. This value must match the actual baud rate of the connection. COM1: This part of the name describes the PC communications port that is used to establish the connection.
WARNING
RSS SLIP connections must be created in pairs. For a given baud rate/ PC communications port combination, create one connection for the device front port and one for the back port. Example: If the SLIP connection CSS_SLIP_FP_9600_COM1 is created, then the following must also be created: CSS_SLIP_BP_9600_COM1. The meets the requirement that a name for be created for both the front and back port on the device.
Naming Convention for Dial-Up Modem install

A Windows RSS SLIP connection name has three items which depend and describe some physical parameters of the connection. A typical RSS SLIP connection name is RSS_SLIP_MDM_FP_9600_COM1, and breaks down is as follows: RSS_SLIP_MDM: This part of the connection name is fixed. All RSS SLIP dial-up modem connections must start with this string. FP: This part of the name describes the device port the connection is capable of connecting with. Possible values are FP (front port) and BP (back port). 9600: This part of the name describes the connections baud rate. This value must match the actual baud rate of the connection. COM1: This part of the name describes the PC communications port that is used to establish the connection.
WARNING
RSS SLIP connections must be created in pairs. For a given baud rate/ PC communications port combination, create one connection for the device front port and one for the back port. Example: If the name CSS_SLIP_FP_9600_COM1 is created, then the following must also be created: CSS_SLIP_BP_9600_COM1. This meets the requirement that a name be created for both the front and back port on the device.
11-34
688 1085E 35-AN
0 6/30 /201 1
CONNECTING TO THE DEVICE
Connecting to the Device ...................................

There are four methods for connecting the PC to the station for downloading software. Use the one appropriate for the installation as outlined below: Serial connection between the PC and a single station (or one of the stations in an IntelliRepeater Ethernet network). See Serial (Direct) Connection on page 11-35. Ethernet connection between PC and a single station (or to the access point in an IntelliRepeater Ethernet network). See Ethernet Connections on page 11-36. Remote connection to a single station (or one of the stations in an IntelliRepeater Ethernet network) using PC and dial-up modem. See Remote Dial-Up Connections on page 11-38. Zone controller link connection using PC and channel banks/modems (IntelliRepeater systems only). See Zone Controller Link Connection on page 11-38.
..
Serial (Direct) Connection

A serial connection may be made between the PC and the RSS port located on the station control module front panel. You may make the connection to either a single station, or to one of the stations in an IntelliRepeater network.
NOTE
ASTRO-TAC receivers can be downloaded only through the serial port.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
11-35
9-PIN EIA-232 MALE D-TYPE CONNECTOR STATION CONTROL MODULE LAPTOP PC
CABLE WIRED FOR NULL MODEM CONNECTIONS 9-PIN EIA-232 FEMALE D-TYPE CONNECTOR RSS PORT ON STATION CONTROL MODULE
Figure 11-1 Serial Connection for Software Download
Ethernet Connections
An Ethernet connection may be made between the PC and either a single station or to the access point of an IntelliRepeater Ethernet network.
11-36
688 1085E 35-AN
0 6/30 /201 1
Laptop PC
3Com Transceiver Terminator
Terminator
Figure 11-2 Ethernet Connection to a Single Station
Terminator
Ethernet access point Connect directly to 3Com transceiver Terminator
Figure 11-3 Ethernet Connection to IntelliRepeater Ethernet Network
IMPORTANT
For IntelliRepeater networks, ensure that each IntelliRepeater station is programmed with a unique IP address. IP addresses are set using RSS. If two IntelliRepeater stations have the same IP address, the network does not work properly. Also, disconnecting any of the IntelliRepeaters Ethernet cables on a functioning system causes the stations to reset.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
11-37
Remote Dial-Up Connections

Using the RSS remote dial-up feature (see Chapter 9, Remote Dial-Up), you may establish a modem connection to a remote station and download the software through telephone lines. This type of connection results in download times comparable to serial connection download times.
RS-232 Phone line RS-232
Station Station modem
PC modem
Laptop with RSS
Figure 11-4 Remote Dial-Up Connection
Zone Controller Link Connection

For SmartZone IntelliRepeater systems (system releases 3.0 and 3.5), you may download the software to a remote station using the zone controller link. This link consists of a cable connected between the zone controller and a local channel bank (typically connected to a remote channel bank through a T1 line) or a local modem. Note that this type of connection results in download times similar to a serial connection, about 10 minutes.The site remains in site trunking for the duration of the download, or a maximum of 30 minutes. The procedure for software download using the zone controller link depends on the parity required by the systems zone controller and whether channel banks or modems can be remotely configured. Use the table below to determine your particular scenario and follow the corresponding procedures to perform the software download.
11-38
688 1085E 35-AN
0 6/30 /201 1
Table 11-1 Zone Controller Link Connection Scenarios Zone Controller Parity Requirements Zone Controller links that require ODD parity Channel Bank (or Modem) Remotely Configurable Issue remote command to Channel Bank (or Modem) to temporarily set parity to NONE. Connect equipment as shown in Zone Controller Link Connection on page 11-38. Perform download procedure provided in Downloading Software to IntelliRepeater Memory on page 11-45). Issue remote command to channel bank (modem) to return parity setting to ODD. Disconnect the zone controller link cable from the PC and reconnect it to the zone controller port (from which it was removed). Zone Controller links that can operate with NO parity Connect equipment as shown in Figure 11-5. Perform download procedure (described in Downloading Software to IntelliRepeater Memory on page 11-45). Disconnect the Zone Controller link cable from the PC and reconnect it to the Zone Controller port from which it was removed. Connect equipment. Perform download procedure (described in Downloading Software to IntelliRepeater Memory on page 11-45). Disconnect the Zone Controller link cable from the PC and reconnect it to the Zone Controller port from which it was removed. Channel Bank (or Modem) Manually Configurable Only This scenario is not practical because a visit to the IntelliRepeater site is required to set parity to NONE for the download and then return the setting to ODD for normal operation. Instead, take PC to the site and perform the software download locally.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
11-39
Note the zone controller port from which you disconnect the link cable; you must reconnect the cable here when the download process is completed. RJ-45 link cable removed from zone controller T1 Line (channel bank or Phone Line (modem)
Station
Adapter Channel bank or modem Channel bank or modem
RSS Laptop
Figure 11-5 Zone Controller Link Connection For some SmartZone IntelliRepeater systems, a DB-9 (female) to RJ-45 (female) adapter is required to connect between the SLIP-equipped PC and the zone controller link that connects to the site to be downloaded, as shown above. The adapter is available at most electronic stores, and should be wired as shown in Figure 11-6.
1
TX 2 RX 3
7 TX 8 RX 3 GND 6 RTS 5 CTS RJ-45 (f) To Link Cable from Zone Controller
To PC COMM Port
4
GND 5
6 RTS 7 CTS 8 9 DB-9 (f)
Figure 11-6 Adapter for Connecting between PC and Zone Controller Link
11-40
688 1085E 35-AN
0 6/30 /201 1
LOADING STATION SOFTWARE FILES ONTO THE PC
Loading Station Software Files onto the PC ...................................

The station operating software is provided on a diskette from Motorola (usually associated with a FLASHport Upgrade option). The files contained on the diskette include the operating software, boot code (optional), and other files required to support the download process. These files must be loaded onto the PC hard disk, as described below.
..
NOTE
About 3 MB of free space is required on the PC hard drive to accommodate the station/receiver software files.
1.
Insert the Station Software disk into the appropriate disk drive. If auto-launch is enabled, then the installation utility launches and window appears. Click OK or Next. An instruction screen appears that prompts for the location to install the software files. The default location is: c:\MRSS\Quantar\<release_name> It is recommended to accept the default. However, if another location is preferred, change to that directory.
2.
3.
Click OK. The installation process provides an indication of the progress.
Downloading Software to Station/Receiver Memory Conventional and 6809 Controller Systems or ASTRO-TAC Comparator Memory ...................................
Conventional and 6809 controller based systems and ASTRO-TAC comparator stations require that the new software be downloaded to each device individually. This procedure must be performed for each device in the system. With the device operating software files copied to the PC hard disk, you are now ready to download the software to the device non-volatile memory (firmware).
1. 2. 3. 4.
Launch the RSS program as outlined in Launching the RSS Program on page 2-12. Connect to the device. Read the current configuration from the device. Verify the currently installed software version by clicking Versions, under Service, in the navigation pane.
..
11-41
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
DOWNLOADING SOFTWARE TO STATION/RECEIVER MEMORY - CONVENTIONAL AND 6809 CONTROLLER SYSTEMS OR ASTRO-TAC COMPARATOR MEMORY CHAPTER 11: SOFTWARE DOWNLOADING
5.
From the File menu, select Software Download.
6. 7.
Set the date and time in the Timestamp fields. Select the appropriate station type in the Station Settings field.
11-42
688 1085E 35-AN
0 6/30 /201 1
RADIO SERVICE SOFTWARE INSTRUCTION MANUAL DOWNLOADING SOFTWARE TO STATION/RECEIVER MEMORY - CONVENTIONAL AND 6809 CONTROLLER SYSTEMS OR ASTRO-TAC COMPARATOR MEMORY
8.
Select the appropriate connection type in the Connection Settings area. This determines the fields that are available. For Ethernet connections: Enter the stations IP address. For serial connections: Configure the following as required for your PC: Serial Port Baud Rate Station Port
For modem connection: Configure the following as required for your PC and system: Serial Port Baud Rate Station Port Click Modem Configuration to configure the modem. The following window appears.
If required, dial into the station by either: Entering the phone number in the Phone Number field or Click Phone book and selecting a preconfigured phone number. The following window appears
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
11-43
DOWNLOADING SOFTWARE TO STATION/RECEIVER MEMORY - CONVENTIONAL AND 6809 CONTROLLER SYSTEMS OR ASTRO-TAC COMPARATOR MEMORY CHAPTER 11: SOFTWARE DOWNLOADING
9.
Click Browse to loacte the upgrade software and then navigating to the files location on your hard drive. Click Program Firmware to start the software download process. The RSS program attempts to establish communications with the station.
10.
NOTE
If problems are encountered, an error message appears.
11.
After communications have been established, the RSS and the station control modules front panel LEDs indicate the software download progress. In the RSS: Progress appears at the bottom of the Software Download window. On the station control module: All LEDs slowly flash, indicating that the station is in download mode. The LEDs flash sequentially up and down (marquee style) as the station downloads the data from DRAM memory to FLASH memory on the station control module. The station resets when the DRAM to FLASH download is complete. If the station also has new wireline software then following reset, the station control module downloads the wireline operating software to the wireline interface module. This is indicated by the two flashing LEDs on the wireline interface module. Otherwise the stations completes its boot process and the station control modules Station On LED lights.
12.
A success message appears on successful software download.
11-44
688 1085E 35-AN
0 6/30 /201 1
DOWNLOADING SOFTWARE TO INTELLIREPEATER MEMORY
IMPORTANT
If the station enters a frozen or locked state, the software modules have not been FLASHed properly. To recover, click Erase Flash, then repeat the download procedure. Click Erase Flash only if you have the software on hand to download to the station. Erasing FLASH renders the station inoperable until software is downloaded.
Downloading Software to IntelliRepeater Memory ...................................

IntelliRepeaters allow software to be downloaded to one IntelliRepeater and then that IntelliRepeater loads the software to all other connected IntelliRepeaters. This is called cross loading. With the station operating software files copied to the PC hard disk, you are now ready to download the software to the station non-volatile memory (firmware).
1. 2. 3. 4.
Launch the RSS program as outlined in Launching the RSS Program on page 2-12. Connect to the device. Read the current configuration from the device. Verify the currently installed software version by clicking Versions, under the Service branch, in the navigation pane. From the File menu, select Software Download.
..
5.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
11-45
6. 7. 8.
Set the date and time in the Timestamp fields. Select the appropriate station type in the Station Settings field. Select the appropriate connection type in the Connection Settings area. This determines the fields available. For Ethernet connections download: Enter the stations IP address. For serial connections: Configure the following as required for your PC: Serial Port Baud Rate Station Port
For modem connection: Configure the following as required for your PC and IntelliRepeater system: Serial Port Baud Rate Station Port
11-46
688 1085E 35-AN
0 6/30 /201 1
Click Modem Configuration to configure the modem. The following window appears.
If required dial into the IntelliRepeater by either: Entering the phone number in the Phone Number field or Click Phone book and select a preconfigured phone number. The following window appears.
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
11-47
9.
Click Browse to locate the upgrade software and then navigating to the files location on your hard drive. Click Program Firmware to start the software download process. The RSS program attempts to establish communications with the station.
10.
NOTE
If problems are encountered, an error message appears.
11.
After communications have been established, the RSS and the LEDs on the station control module front panel indicate the software download progress. In the RSS: Progress appears at the bottom of the Software Download window. On the station control module: All LEDs slowly flash, indicating that the station is in download mode. The LEDs flash sequentially up and down (marquee style) as the station downloads the data from DRAM memory to FLASH memory on the station control module. The station resets when DRAM to FLASH download is complete. If the station also has new wireline software, then reset station control module downloads the wireline operating software to the wireline interface module. This is indicated by the two flashing LEDs on the wireline interface module. Otherwise the stations completes the boot process and the station control modules Station On LED lights.
12.
A success message appears on successful software download.
IMPORTANT
If the station enters a frozen or locked state, the software modules have not been FLASHed properly. To recover, click Erase Flash, then repeat the download procedure. Click Erase Flash only if you have the software on hand to download to the station. Erasing FLASH renders the station inoperable until software is downloaded.
NOTE
In an IntelliRepeater network, when the software download has completed to one station, all other stations in the network are automatically crossloaded, through Ethernet, so that they are all running the same version of software.
11-48
688 1085E 35-AN
0 6/30 /201 1
APPENDIX
PL/DPL Codes
A
4Z 4A 4B 5Z 5A 5B 6Z 6A 6B 7Z 7A M1 8Z M2 M3 M4 9Z M5 M6 M7
................................... ....
Table A-1 Tone Private-Line (PL) Codes Frequency (Hz) 67.0 69.3 71.9 74.4 77.0 79.7 82.5 85.4 88.5 91.5 94.8 97.4 100.0 103.5 107.2 110.9 114.8 118.8 123.0 127.3 131.8 Motorola Code XZ WZ XA WA XB WB YZ YA YB ZZ ZA ZB 1Z 1A 1B 2Z 2A 2B 3Z 3A 3B Frequency (Hz) 136.5 141.3 146.2 151.4 156.7 162.2 167.9 173.8 179.9 186.2 192.8 203.5 206.5 210.7 218.1 225.7 229.1 233.6 241.8 250.3 Motorola Code
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
A-1
CHAPTER A: PL/DPL CODES
Table A-2 Digital Private-Line (DPL) Codes Digital Codes 023 025 026 031 032 043 047 051 054 065 071 072 073 074 114 115 125 131 132 134 Digital Codes 143 152 155 156 162 165 172 205 223 226 243 244 245 251 261 263 265 271 306 311 Digital Codes 315 331 343 346 351 364 365 371 411 412 413 423 431 432 445 464 466 503 506 516 Digital Codes 532 546 565 606 612 624 627 631 645 662 664 703 712 723 731 732 734 743 754
A-2
688 1085E 35-AN
0 6/30 /201 1
APPENDIX
dBm to Microvolts Conversion

................................... ....
Table B-1 dBm to Microvolts Conversion dBm -80 -81 -82 -83 -84 -85 -86 -87 -88 -89 -90 -91 -92 -93 -94 -95 -96 -97 -98 -99 -100 -101 -102 -103 Microvolts 22.3606 19.9289 17.7617 15.8301 14.1086 12.5743 11.2068 9.9881 8.9019 7.9338 7.0710 6.3020 5.6167 5.0059 4.4615 3.9763 3.5439 3.1585 2.8150 2.5089 2.2360 1.9928 1.7761 1.5830 dBm -106 -107 -108 -109 -110 -111 -112 -113 -114 -115 -116 -117 -118 -119 -120 -121 -122 -123 -124 -125 -126 -127 -128 -129 Microvolts 1.1206 0.9988 0.8901 0.7933 0.7071 0.6302 0.5616 0.5005 0.4461 0.3976 0.3543 0.3158 0.2815 0.2508 0.2236 0.1992 0.1776 0.1583 0.1410 0.1257 0.1120 0.0998 0.0890 0.0793
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
B-1
CHAPTER B: DBM TO MICROVOLTS CONVERSION
Table B-1 dBm to Microvolts Conversion (continued) dBm -104 -105 Microvolts 1.4108 1.2574 dBm -130 Microvolts 0.0707
B-2
688 1085E 35-AN
0 6/30 /201 1
APPENDIX
Glossary
................................... ....
Term Alignment
Definition Adjustment procedures, usually aided by RSS program, that set the station operating parameters to meet the specifications; Includes deviation, power out, and wireline levels. Codeplug backup file. Base station. The type of station in which transmit and receive frequencies, usually the same. Operates in simplex mode only. Method of adjusting a circuit to meet critical operating parameters. FCC-assigned ID of the licensee. Typically in alphanumeric form and broadcast periodically during station operation. One of several methods of opening the receiver path and unmuting the audio path to the speaker. Other methods are PL, DPL, and ASTRO. A pair of frequencies, transmit and receive, used for a single communications path. The area of non-volatile memory in the station that stores the station configuration, calibration, and personality profiles. The serial communications port(s) available on a PC. Usually COM1 through COM4. Data placed into RSS data fields either as a placeholder or as typical data for the particular field. Default data may be edited as necessary. Turn off the station transmitter. The amount of variance (+ or -) from the carrier frequency caused by audio or data modulation. Typically expressed in + or - kHz.
Archive Files Base Calibration Call Sign Carrier Squelch
Channel Codeplug COMX Defaults
Dekey Deviation
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
C-1
CHAPTER C: GLOSSARY
Term Failsoft
Definition A station operating mode entered when the trunking central controller is either unavailable or nonfunctional. This provides basic operation until the trunking central controller is available or becomes functional. Area on the display in which data may be entered or edited. Simultaneous transmit and receive. Turn on the stations transmitter. Set of parameters, settings, and features that define the operation of a station. This includes specifics such as operating frequencies, output power, and squelch type. A type of station in which any signal received is subsequently transmitted. This requires different frequencies for transmit and receive. Type of secure radio communications using a proprietary protocol for signaling and encryption/decryption. Radio communications system in which voice/data to be transmitted is sent to multiple sites and transmitted simultaneously to provide wide area coverage. Methods of eliminating noise from the speaker when no received signal is present. Three common types of squelch are carrier (CSQ), Pl, and DPL. Indicates that the station is equipped to operate in a digital system, but is not capable of encryption or decryption. Allocation of station resources by a central controller in accordance with configured rules. This allows a relatively small amount of station resources to be dynamically shared amongst subscribers. Typically a phone line connection between a console and a station.
Field Full Duplex Key Personality
Repeater
SECURENET Simulcast
Squelch
Transparent Trunking
Wireline
C-2
688 1085E 35-AN
0 6/30 /201 1
APPENDIX
Acronyms
................................... ....
Acronym AMSS ASCII AES COM COAM CHAN CONV CSQ CTCSS DOS DPL DRAM DTMF DVM EPROM EEPROM FREQ FTR ID kHz LED
Definition Automatic Multiple Site Selection American Standard Code Information Interchange Area Systems Engineer Communications port Customer Owned and Maintained Channel Conventional; conversation Carrier Squelch Continuous Tone Coded Squelch System Disk Operating System Digital Private Line (coded squelch) Dynamic Random Access Memory Dual Tone Multiple Frequency Digital Volt Meter Erasable Programmable Read-Only Memory Electrically Erasable Programmable Read-Only Memory Frequency Field Technical Representative Identification kilohertz (1000 Hz) Light Emitting Diode
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
D-1
CHAPTER D: ACRONYMS
Acronym LLGT MHz MRSS MSS NSO NST PC PL PROM PTT RAM RSS RX TOT TPL TX
Definition Low Level Guard Tone (typically 2175 Hz) Megahertz (1,000,000 Hz) Motorola Radio Service Software Motorola Service Station National Service Organization National Service Training Personal Computer Private Line (coded squelch) Programmable Read-Only Memory Push To Talk Random Access Memory Radio Service Software Receive Time Out Timer Tone Private Line squelch Transmit
D-2
688 1085E 35-AN
0 6/30 /201 1
INDEX
Index
.........................
. . . . . . . . . . . . . . . . . . . . . . . .A . . .
Access Modem Requirements . . . . . . . . . . . . . . . . . . . . .9-2 Modem, PC Configuration . . . . . . . . . . . . . . . . . .9-3 Modem, RSS PC Configuration Fields. . . . . . . . . .9-5 Modem, Station Configuration . . . . . . . . . . . . . . .9-2 Remote Dial-Up . . . . . . . . . . . . . . . . . . . . . . . . .9-1 Access code table 6809 trunking field definitions . . . . . . . . . . . . . .3-15 Conventional field definitions . . . . . . . . . . . . . . .3-14 programming for 6809 trunking systems . . . . . . .3-15 programming for conventional systems . . . . . . . .3-13 Alignment Alignment Procedures . . . . . . . . . . . . . . . . . . . . .6-2 ASTRO Bit Error Rate . . . . . . . . . . . . . . . . . . . .3-90 ASTRO Test Pattern Generation . . . . . . . . . . . . .3-85 ASTRO Tx Align and Test . . . . . . . . . . . . . . . . .3-82 AstroTAC Comparator Battery Equalization . . . . . . . . . . . . . . . . . .4-10 Reference oscillator. . . . . . . . . . . . . . . . . . .4-10 Astro-TAC comparator Overview . . . . . . . . . . . . . . . . . . . . . . . . . . .4-9 Battery Equalization . . . . . . . . . . . . . . . . . . . . .3-73 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-54 Post-Repair Alignment Overview . . . . . . . . . . . . .6-1 Power Output Alignment Procedure . . . . . . . . . . .6-4 Power Output Alignment Procedure, 350W VHF Stations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-7 Reference Modulation Alignment Procedure . . . .6-14 Reference oscillator . . . . . . . . . . . . . . . . . . . . . .3-75 RSSI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-68 Rx Wireline . . . . . . . . . . . . . . . . . . . . . . . . . . .3-55 Squelch Adjust . . . . . . . . . . . . . . . . . . . . . . . . .3-71 TDATA Calibration . . . . . . . . . . . . . . . . . . . . . .3-88 Tx Deviation Alignment Procedure, 350W VHF Stations 6-11 Tx Wireline. . . . . . . . . . . . . . . . . . . . . . . . . . . .3-55 Archive File Opening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-24 Archive, Saving Data to . . . . . . . . . . . . . . . . . . . . . .2-22 ASTRO Bit Error Rate, Reports. . . . . . . . . . . . . . . . .3-90 ASTRO Test Patterns, Generation . . . . . . . . . . . . . . .3-85 ASTRO Tx, Align and Test procedure . . . . . . . . . . . .3-82 Auxiliary Input Programming . . . . . . . . . . . . . . . . . . . . . . . . . .10-2 Auxiliary Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-2 Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-3 Auxiliary Output Programming . . . . . . . . . . . . . . . . . . . . . . . . . .10-5 Auxiliary Outputs. . . . . . . . . . . . . . . . . . . . . . . . . . .10-4 Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-5
. . . . . . . . . . . . . . . . . . . . . . . .B . . .
Backplane ID Reading from comparator . . . . . . . . . . . . . . . . . .7-18 Battery, Equalization . . . . . . . . . . . . . . . . . . . 3-73, 4-10 Bit Error Rate, Reports . . . . . . . . . . . . . . . . . . . . . . .3-90
. . . . . . . . . . . . . . . . . . . . . . . .C . . .
Codeplug Getting Size . . . . . . . . . . . . . . . . . . . . . . . . . . .2-21
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
INDEX-1
Opening an Archive . . . . . . . . . . . . . . . . . . . . . 2-24 Printing a Report . . . . . . . . . . . . . . . . . . . . . . . 5-31 Reading the Station. . . . . . . . . . . . . . . . . . . . . . 2-14 Reports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-31 Reports, Saving . . . . . . . . . . . . . . . . . . . . . . . . 5-32 Verifying Station Data . . . . . . . . . . . . . . . . . . . . 3-3 Writing to Station . . . . . . . . . . . . . . . . . . . . . . . 2-20 Comparator Analog Voting System screen . . . . . . . . . . . . . . . 4-7 Analog Voting System screen fields . . . . . . . . . . . 4-7 Conventional System screen . . . . . . . . . . . . . . . . 4-5 Conventional System screen fields . . . . . . . . . . . . 4-5
Hardware Configuration screen . . . . . . . . . . . . . . 4-3 Hardware Configuration screen fields . . . . . . . . . . 4-4 Optimizing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 Port Control screen . . . . . . . . . . . . . . . . . . . . . . . 4-8 Port Control screen fields . . . . . . . . . . . . . . . . . . 4-8 Programming . . . . . . . . . . . . . . . . . . . . . . . 4-1, 4-3 Retrieving Backplane ID . . . . . . . . . . . . . . . . . . 7-18 Smartzone System screen . . . . . . . . . . . . . . . . . . 4-6 Smartzone System screen fields . . . . . . . . . . . . . . 4-6 Verifying configuration . . . . . . . . . . . . . . . . . . . . 4-2 Compatibility Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
. . . . . . . . . . . . . . . . . . . . . . . .D . . .
Date and Time Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-30 dBm to Microvolts Conversion Table . . . . . . . . . . . . . B-1 Diagnostics AstroTAC Comparator Fan check . . . . . . . . . . . . . . . . . . . . . . . . . 5-34 Overview . . . . . . . . . . . . . . . . . . . . . . . . . 3-93, 5-1 Dial-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1 Modem Requirements . . . . . . . . . . . . . . . . . . . . . 9-2 PC Configuration . . . . . . . . . . . . . . . . . . . . . . . . 9-3 RSS PC Configuration Fields. . . . . . . . . . . . . . . . 9-5 Station Configuration . . . . . . . . . . . . . . . . . . . . . 9-2 Disabling Remote Station Disabling . . . . . . . . . . . . . . . . . 5-33 DPL codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
. . . . . . . . . . . . . . . . . . . . . . . .E . . .
Enabling Remote Station Enabling . . . . . . . . . . . . . . . . . . 5-33
. . . . . . . . . . . . . . . . . . . . . . . .F . . .
Feature Summary, RSS . . . . . . . . . . . . . . . . . . . . . . . 2-1 File Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21 Saving to Archive . . . . . . . . . . . . . . . . . . . . . . . 2-22 Firmware Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1 Features and System Capabilities . . . . . . . . . . . . 7-22 RSS Program Version Relationship . . . . . . . . . . . 7-2 Upgrade. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
. . . . . . . . . . . . . . . . . . . . . . . . I. . .
Installing RSS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
. . . . . . . . . . . . . . . . . . . . . . . .M . . .
Metering, Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
INDEX-2
688 1085E 35-AN
0 6/30 /201 1
. . . . . . . . . . . . . . . . . . . . . . . .N . . .
Network Operation Setting the Date and Time . . . . . . . . . . . . . . . . . .3-8 Setting the IP Address . . . . . . . . . . . . . . . . . . . . .3-6 Setting the MAC Address . . . . . . . . . . . . . . . . . . .3-7
. . . . . . . . . . . . . . . . . . . . . . . .O . . .
Optimization Date and Time Setting . . . . . . . . . . . . . . . . . . . . .3-8 IP Address Setting . . . . . . . . . . . . . . . . . . . . . . . .3-6 MAC Address Setting . . . . . . . . . . . . . . . . . . . . .3-7 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1 Post-Optimization Checkout . . . . . . . . . . . . . . . .3-93 Required Equipment . . . . . . . . . . . . . . . . . . . . . .3-2 StationType Program Overview . . . . . . . . . . . . . .3-5 Verifying Station Data . . . . . . . . . . . . . . . . . . . . .3-3 Wireline Configuration. . . . . . . . . . . . . . . . . . . . .3-9 Wireline Configuration Fields. . . . . . . . . . . . . . .3-10 Optimizing Comparator . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1 Programming . . . . . . . . . . . . . . . . . . . . . . . .4-3 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-1
. . . . . . . . . . . . . . . . . . . . . . . .P . . .
Password Activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-1 Bypassing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-6 Changing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-3 Creation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-2 Erasing, Local . . . . . . . . . . . . . . . . . . . . . . . . . . .8-4 Erasing, Remote . . . . . . . . . . . . . . . . . . . . . . . . .8-5 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-2 Protection Overview . . . . . . . . . . . . . . . . . . . . . .8-1 Timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-1 PC Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-4 PL Codes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
. . . . . . . . . . . . . . . . . . . . . . . .R . . .
Reference Oscillator, Alignment . . . . . . . . . . . 3-75, 4-10 Remote Disabling a Station. . . . . . . . . . . . . . . . . . . . . . .5-33 Enabling a Station . . . . . . . . . . . . . . . . . . . . . . .5-33 Repair Alignment Procedures . . . . . . . . . . . . . . . . . . . . .6-2 Output Power Alignment Procedure . . . . . . . . . . .6-4 Output Power Alignment Procedure, 350W VHF Stations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-7 Post-Repair Alignment Overview . . . . . . . . . . . . .6-1 Reference Modulation Alignment Procedure . . . .6-14 Tx Deviation Alignment Procedure, 350W VHF Stations 6-11 Reports Codeplug . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-31 Printing Codeplug Report . . . . . . . . . . . . . . . . . .5-31 Saving a Codeplug Report . . . . . . . . . . . . . . . . .5-32 Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-3 RSS Connecting PC to Station . . . . . . . . . . . . . . . . . .2-11 Exiting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-13 Feature Summary . . . . . . . . . . . . . . . . . . . . . . . .2-1 Firmware Relationship . . . . . . . . . . . . . . . . . . . . .7-2 Installation Procedure. . . . . . . . . . . . . . . . . . . . . .2-4 Launching. . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-12 PC Requirements . . . . . . . . . . . . . . . . . . . . . . . . .2-4 Program Versions Compatibility . . . . . . . . . . . . .7-16 Screen Overview . . . . . . . . . . . . . . . . . . . . . . . .2-17 User Interface Description . . . . . . . . . . . . . . . . . .2-2 RSSI Alignment. . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-68 Rx Wireline, Alignment . . . . . . . . . . . . . . . . . . . . . .3-55
. . . . . . . . . . . . . . . . . . . . . . . .S . . .
Security Password Activation . . . . . . . . . . . . . . . . . . . . . .8-1 Password Bypassl . . . . . . . . . . . . . . . . . . . . . . . .8-6 Password Change . . . . . . . . . . . . . . . . . . . . . . . .8-3
68 8 10 85 E3 5 -A N
06 / 30 / 20 11
INDEX-3
Password Creation . . . . . . . . . . . . . . . . . . . . . . . 8-2 Password Erasure, Local . . . . . . . . . . . . . . . . . . . 8-4 Password Erasure, Remote . . . . . . . . . . . . . . . . . 8-5 Password Features . . . . . . . . . . . . . . . . . . . . . . . 8-2 Password Protection . . . . . . . . . . . . . . . . . . . . . . 8-1 Password Protection Overview. . . . . . . . . . . . . . . 8-1 Password timeout . . . . . . . . . . . . . . . . . . . . . . . . 8-1 SLIP Naming Convention . . . . . . . . . . . . . . . . . . . 11-33 Software Versions . . . . . . . . . . . . . . . . . . . . . . . . 7-17, 7-18 Software Downloading Downloading Software to Station, 6809 Controller Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-40 Downloading Software to Station, IntelliRepeater Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-44 Installing Dial-Up Modem in Windows XP Professional 11-15 Installing Null Modem in Windows XP Professional113 Loading Station Software to PC . . . . . . . . . . . . 11-40 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1 PC Preparation . . . . . . . . . . . . . . . . . . . . . . . . . 11-3 Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . 11-2 RSS SLIP Naming Convention . . . . . . . . . . . . 11-33 Station Connection, Ethernet . . . . . . . . . . . . . . 11-35
Station Connection, Overview . . . . . . . . . . . . . 11-34 Station Connection, Remote Dial-Up . . . . . . . . 11-37 Station Connection, Serial . . . . . . . . . . . . . . . . 11-34 Station Connection, Zone Controller Link . . . . . 11-37 Software Version Station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-30 Squelch Adjust, Alignment . . . . . . . . . . . . . . . . . . . 3-71 State/Action Tables . . . . . . . . . . . . . . . . . . . . . . . . . 10-6 Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-9 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-7 Programming . . . . . . . . . . . . . . . . . . . . . . . . . . 10-8 Station Retrieving Station ID . . . . . . . . . . . . . . . . . . . . 7-17 Status Astro-TAC Comparator Panel Screen . . . . . . . . . . . . . . . . . . . . . . . 5-28 Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 Messages, Station Generated . . . . . . . . . . . . . . . . 5-6 Metering Screens . . . . . . . . . . . . . . . . . . . . . . . . 5-2 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 Panel Button Definitions . . . . . . . . . . . . . . . . . . 5-27 Panel Screen . . . . . . . . . . . . . . . . . . . . . . . . . . 5-26 Reports Screen . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3 Station Software Versions . . . . . . . . . . . . . . . . . 5-30
. . . . . . . . . . . . . . . . . . . . . . . .T . . .
TDATA Calibration, Alignment . . . . . . . . . . . . . . . . 3-88 Tx Wireline, Alignment . . . . . . . . . . . . . . . . . . . . . . 3-55
. . . . . . . . . . . . . . . . . . . . . . . .U . . .
Upgrade Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1 Performing. . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-19 User Interface Description . . . . . . . . . . . . . . . . . . . . . 2-2
. . . . . . . . . . . . . . . . . . . . . . . .W . . .
WildCard Auxiliary Input Fields . . . . . . . . . . . . . . . . . . . . Auxiliary Input, Programming . . . . . . . . . . . . . . Auxiliary Inputs . . . . . . . . . . . . . . . . . . . . . . . . Auxiliary Output . . . . . . . . . . . . . . . . . . . . . . . Auxiliary Output Fields. . . . . . . . . . . . . . . . . . . Auxiliary Output, Programming. . . . . . . . . . . . . Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . State/Action Tables. . . . . . . . . . . . . . . . . . . . . . State/Action Tables, Fields . . . . . . . . . . . . . . . . 10-3 10-2 10-2 10-4 10-5 10-5 10-1 10-6 10-9 State/Action Tables, Overview. . . . . . . . . . . . . . 10-7 State/Action Tables, Programming . . . . . . . . . . . 10-8 Wireline Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9 Configuration Fields . . . . . . . . . . . . . . . . . . . . . 3-10
INDEX-4
688 1085E 35-AN
0 6/30 /201 1

6881085E35-An QUANTAR QUANTRO Radio Service Software Instruction Manual

Uploaded by

Copyright:

Available Formats

6881085E35-An QUANTAR QUANTRO Radio Service Software Instruction Manual

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

6881085E35-An QUANTAR QUANTRO Radio Service Software Instruction Manual

Uploaded by

Copyright:

Available Formats

What does the document discuss regarding copyright of Motorola software?

What does the document discuss regarding copyright of Motorola software?

What warranty does Motorola provide for its software?

What warranty does Motorola provide for its software?

QUANTAR/QUANTRO

RADIO SERVICE SOFTWARE INSTRUCTION MANUAL

2011 MOTOROLA SOLUTIONS, INC. ALL RIGHTS RESERVED PRINTED IN U.S.A.

Computer Software Copyrights

WARRANTY Limited Software Warranty

Limited Media Warranty

Chapter 2: RSS Overview

688 1085E 35-AN

RADIO SERVICE SOFTWARE INSTRUCTION MANUAL

Chapter 4: Optimizing the ASTRO-TAC Comparator

Chapter 5: Diagnostics and Status

Chapter 6: Performing Post Repair Alignment

Chapter 7: Version Compatibility and Upgrades

Chapter 8: Password Protection

Chapter 9: Remote Dial-Up

Chapter 10: WildCard Operation

Chapter 11: Software Downloading

688 1085E 35-AN

RADIO SERVICE SOFTWARE INSTRUCTION MANUAL

688 1085E 35-AN

688 1085E 35-AN

RADIO SERVICE SOFTWARE INSTRUCTION MANUAL

THIS PAGE INTENTIONALLY LEFT BLANK.

688 1085E 35-AN

688 1085E 35-AN

Intended User Profile ...................................

ORGANIZATION OF THIS GUIDE

Organization of this Guide ...................................

688 1085E 35-AN

RADIO SERVICE SOFTWARE INSTRUCTION MANUAL

Related Manuals ...................................

THIS PAGE INTENTIONALLY LEFT BLANK.

688 1085E 35-AN

Summary of Features ...................................

USER INTERFACE DESCRIPTION

CHAPTER 2: RSS OVERVIEW

User Interface Description ...................................

Navigation pane Status bar

Figure 2-1 RSS Window Overview

688 1085E 35-AN

RADIO SERVICE SOFTWARE INSTRUCTION MANUAL

USER INTERFACE DESCRIPTION

File Open File Save Read Configuration From Device

Context Sensitive Help

Open Connection Screen Open Codeplug Properties

Write Configuration To Device

Figure 2-2 RSS Toolbar Buttons

Figure 2-3 RSS Menus

CHAPTER 2: RSS OVERVIEW

Installing the RSS Software ...................................

688 1085E 35-AN

RADIO SERVICE SOFTWARE INSTRUCTION MANUAL

INSTALLING THE RSS SOFTWARE

INSTALLING THE RSS SOFTWARE

CHAPTER 2: RSS OVERVIEW

688 1085E 35-AN