Scribd Logo
Upload

Welcome to Scribd!

  • 18 views

    RRU PWR Calculation

    Uploaded by

    turi313
    Deep dive in to rru power calculations

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd

    RRU PWR Calculation

    Uploaded by

    turi313
    18 views4 pages
    Deep dive in to rru power calculations

    Original Title

    RRU Pwr calculation

    Copyright

    © © All Rights Reserved

    Available Formats

    DOCX, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Deep dive in to rru power calculations

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    18 views4 pages

    RRU PWR Calculation

    Uploaded by

    turi313
    Deep dive in to rru power calculations

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    of 4

    How to calculate the power of eRRU3232

    Publication Date: 2017-10-24


    Issue Description
    The customer wants to know about the difference between the power of RRUs.

    The first RRU: FunctionModule,eRRU3232,WD5MPSRB1C0,Multi-mode Multi-carriers Remote Radio Unit (TX3600-3800MHz/RX3600-3800MHz,4T4R,With

    installation kits,SP) which accepts 10W per port.

    The second RRU: FunctionModule,eRRU3232,WD5MPSRB1CA,Multi-mode Multi-carriers Remote Radio Unit (TX3670-3700MHz/RX3670-

    3700MHz,4T4R,With installation kits) which accepts 8Ws per port.

    These values are not the same because the customer ordered different equipment
    configuration.

    This result is based on the formula for the output power:

    Solution
    The see the PA value you need to list the below parameters with the LST CELLDLPCPDSCHPA
    command:
    To list PA parameters related to PDSCH power control for the cell with
    Local cell identity of 0, run the following command:
    LST CELLDLPCPDSCHPA: LocalCellId=0;
    The result is shown as follows:
    +++ 0 2016-03-14 14:54:22
    O&M #806384666
    %%LST CELLDLPCPDSCHPA: LocalCellId=0;%%
    RETCODE = 0 Operation succeeded.

    List Pa parameters for PDSCH power control


    ------------------------------------------
    Local cell ID = 0
    PA adjusting switch = Off
    PA for even power distribution(dB) = -3 dB
    PA for PTP User(dB) = -3 dB
    PA for Video User(dB) = -3 dB
    (Number of results = 1)

    --- END

    Local cell ID Indicates the local ID of the cell. It uniquely identifies a cell within a BS.

    PA adjusting switch Indicates the switch for adjusting the PA through power control on the PDSCH. If this p
    when the channel quality is extremely good or bad.

    PA for even power Indicates the PA to be used when PA adjustment for PDSCH power control is disabled

    distribution(dB) used for the PDSCH.

    PA for PTP User(dB) Indicates the PA used for PDSCH power control.

    PA for Video User(dB) Indicates the PA value used in a Video. A proper PA setting helps power control for vid

    The see the PB value you need to list the below parameters with the LST CELLDLPCPDSCHPA
    command:
    To list the PDSCH configuration of the cell with Local cell ID of 0, run
    the following command:
    LST PDSCHCFG: LocalCellId=0;
    The result is shown as follows:
    +++ HUAWEI 2013-06-24 16:08:08
    O&M #12379
    %%LST PDSCHCFG: LocalCellId=0;%%
    RETCODE = 0 Operation succeeded.

    Display PDSCHCfg
    ----------------
    Local cell ID = 0
    Reference signal power(0.1dBm) = 182
    PB = 1
    Reference Signal Power Margin(0.1dB) = 0
    Offset of Ant0 to Tx Power(0.1dB) = 255
    Offset of Ant1 to Tx Power(0.1dB) = 255
    Offset of Ant2 to Tx Power(0.1dB) = 255
    Offset of Ant3 to Tx Power(0.1dB) = 255
    (Number of results = 1)

    --- END

    Local cell ID Indicates the local ID of the cell. It uniquely identifies a cell within a BS.
    Reference signal Indicates the cell reference signal power of each physical antenna. However, th
    power(0.1dBm)
    PB Indicates the scaling factor index of the Energy Per Resource Element (EPRE)
    3GPP TS 36.213.
    Reference Signal Power Indicates the cell reference signal power headroom of each physical antenna. T
    Margin(0.1dB)
    Offset of Ant0 to Tx Indicates the offset of the TX power of physical channel 0 relative to the baselin
    Power(0.1dB) If the TX power configurations should be the same between physical channels,
    parameter to a proper value based on the actual situation. This parameter appl
    Offset of Ant1 to Tx Indicates the offset of the TX power of physical channel 1 relative to the baselin
    Power(0.1dB) If the TX power configurations should be the same between physical channels,
    parameter to a proper value based on the actual situation. This parameter appl

    Offset of Ant2 to Tx Indicates the offset of the TX power of physical channel 2 relative to the baselin
    Power(0.1dB) If the TX power configurations should be the same between physical channels,
    parameter to a proper value based on the actual situation. This parameter appl
    Offset of Ant3 to Tx Indicates the offset of the TX power of physical channel 3 relative to the baselin
    Power(0.1dB) If the TX power configurations should be the same between physical channels,
    parameter to a proper value based on the actual situation. This parameter appl

    So if the RS configuration 122, then it is 7.5 (watts)

    If RS is configured for 134, it is 10 (watts)

    You might also like