Republic of the Philippines

Department of Education
Region V
Division of Masbate
DAMASO R. RUBIA MEMORIAL HIGH SCHOOL
San Agustin, Aroroy, Masbate
_______________________________________________________________________________________________

T.L.E. 8
Fourth Quarter Examination
SY. 2023-2024
Name of Learner: ____________________________ Date: ____________________________
Grade Level and Section: ______________________ Score: ___________________________

Direction: Identify what is asked or described in each item. Write the letter of the correct answer.
1. It is the skill or work of making or fixing wooden objects or wooden parts of buildings.
A. Carpentry B. Carpenter C.Tools D. Materials
2. It is a person whose job is making and repairing wooden things.
A. Carpenter B. Carpentry C. Materials D. Tools
3. It is a material used for partitions, floors, ceilings, and sheating.
A. Cement B. Mallet C. Gravel D. Plywood
4. The following are tools needed in carpentry EXCEPT.
A. Cement B.Mallet C. Try square D. Hammer
5. It is a raw products that you make something with which could be just about anything such as wood, metals, plants,
liquids, and chemicals.
A. Tool. B. Materials C. Equipment's D. All of the above
6. The following are materials needed in carpentry EXCEPT.
A. Cement B. Nails C.Gravel D. Hammer
7. It is a tool used in squaring, measuring, and testing the squareness of a wood.
A. Mallet B. Try square. C. Gravel D. Hammer
8. Which material refers to sawn timber?
A. Lumber. B. Gravel C. Plywood D. Wood
9. Which classification of hand tool does an Auger bit belong?
A. Measuring tool. C. Boring tools
B. Tooth-cutting tools. D. Edge-cutting tools
10. What tooth-cutting tools are you going to use if you want to cut a piece of wood into pieces
A. Cross-cut saw B. Coping saw C.Back saw D.Dovetail saw
11. Which is the correct way of inspecting the materials?
A. Count the number of tools and set it aside
B. Look for defective items and dispose it immediately
C. In case of missing part, look for a replacement to improve it.
D. Check if the materials and tools are complete in terms of quantity quality and specification.
12. Which classification of hand tools does a Turning saw belong?
A. Tooth-cutting tools B. Boring tools C. Testing tools D. Edge-cutting tools
13. Which does not belong Marking lining tools?
A. Pencil B. Marking gauge C. Compass D. Caliper
14. It is a tool used to trim and shape wood.
A. Chisel B. Plane C. Spoke shave D. Cabinet scraper
15. It is a tool used to cut the wood along the grain.
A. Cross-cut saw B. Rip-saw C. Compass saw D. Coping saw
16. What will you use to get the details in the amount of materials of the project
A. Quantity B. Materials C. Unit price D. Requisition unit
17. It is a tool used for testing vertical and horizontal surfaces.
A. Spirit level B Plumb bob C .Steel square D. Try square
18. It is used to lay out or mark cutting lines.
A. Marking gauge B. Pencil C. Chalk line D. Divider
19. Which is not an example of marking lining tools.
A. Pencil B. Chalk line C. Divider D. Try square
20. Which tool is not an example of Edge cutting tools?
A. Cross-cut saw B. Rip saw C. Turning saw D. Plumb bob
21. Which material refers to coarse aggregate.
A. Gravel B. Plywood C. Cement D. Sand
22. Which of the following is a boring tool?
A. Claw hammer B. Chisel C. Screw driver D. Drill bit
23. What is the form that you need to fill in if you want to write a written request.
A. Requisition form B. Toll C. Bill D. Work
24. Which is NOT an example of materials?
A. Level bar B. Lumber C. Water D. Nail
25. Which of the following is NOT a part of a bill of materials?
A. Amount B. Quality C. Unit cost D Quantity
26. These are all examples of edges cutting tools EXCEPT;
A. Plumb bob B. Plane C. Chisel D. Spoke shave
27. It is a measuring tools that used to transfer measurements from the ruler to the work.
A. Caliper B. meter stick C. pull-push rule D. ruler
28. It is a measuring tool that used to measure a work piece.
A. meter stick B. pencil C. divider D. ruler
29. It is a tool used to make hole in woods.
A. Auger bit B. expansive bit C. rip-saw D. chisel
30. It is a tool used for testing vertical and horizontal surfaces.
A. plumb bob B. spirit level C. steel square D. coping saw
31. Which of the following materials is needed to construct a cabinet?
A. cement B. plywood C. sand D. gravel
33. The price of one (1) hammer that Kate's father just bought is 200.00 pesos. What part of the bill of material is 200.00
pesos?
A. requisition unit C. unit price
B. quantity D. materials and description
34. Why is it important to check and inspect the materials and tools for any defect and damage before receiving them?
A. So you can count the materials and tools properly
B. So you will know how many damaged materials and tools
C. So that you can ask for replacements if you found it to be defective
D. So you can reprimand the supplier for delivering damaged materials or tools
35. What part of the bill of materials are the term kilogram, liter, piece and foot found?
A. requisition unit C. unit price
B. quantity D. materials and description
36. Which hand tool would you pick if you were asked to find and get a measuring tool?
A. marking gauge B. pull-push rule C. chalk line D. pencil
37. Which of the following hand tool is NOT a testing tool?
A. try square B. steel square C. spoke shave D. plumb bob
38. Which of the following DOES NOT belong to the measuring tools?
A. pull-push rule B. try square C. steel square D. caliper
39. It is a material made of metal used for fastening woods.
A. nails B. lumber C. cement D. gravel
40. It states the detailed name of the materials.
A. description B. specification C. total amount D. unit
41. It is a powdered substance mixed with water.
A. cement B. sand C. nail D. lumber
42. In laying out and marking the thickness and width of the stock, the BEST tool to use is _____________________.
A. pencil B. ruler C. marking gauge D. all of the above
43. It is a buy product of lumber which is made of large thin layers or sheets of woods called piles.
A. ply board B. wood lumber C. plywood D. hard lumber
44. Tool used for cutting across the grain.
A. rip-saw B. cross-cut saw C. caliper D. pull-push rule
45. A tool for measuring long distance.
A. ruler B. try square C. pull-push rule D. meter stick
46. It is a flexible tape that slides into a material case and it is used to measure irregular and regular shapes.
A. pull-push rule B. ruler C. caliper D. pencil
47. It is used for laying out and scribing arcs and circles.
A. protractor B. divider C. ruler D. compass
48. A folded measuring tool commonly used for overhead measurement.
A. caliper B. meter stick C. pull-push rule D. zigzag rule
49. Which is used to drive and pull out nails on a wooden.
A. claw hammer B. screwdriver C. cabinet scraper D. mallet
50. Which is used to protect hands while working?
A. claw hammer B. gloves C. screwdriver D. facemask

PREPARED BY: CHECKED BY: NOTED:

ROSEFE B. REGALA MARICEL C. CALUSA GENARO FRANCISCO III

ROSEFE B. REGALA
TLE Pre – Service Teacher

CHECKED BY:

MARICEL C. CALUSA
Cooperating Teacher/ Teacher I

NOTED:

GENARO FRANCISCO III