A.

s7M- d3795
RANGER APPAREL EXPORT APPAREL PVT. LTD RANER

Beesely Balance

Introduction:

Beesely balance is used to determine the count of yarn directly in any system like, Ne, Tex, Metric,
Worsted, Denier etc.

Product Details:
Beesely balance is completely made of mild steel duly painted and the internal assembly is made out of Stainless
Steel. Sliding glass door is provided for trouble free operation from external hindrance. The equipment is
supplied with specially designed template for preparing sample for testing. Leveling of the instrument can be
easily maintained with leveling screw.

Special features:

Direct yarn count balance.

Easy to operate & reliable.
It requires no calculations for results.
Tabletop model easy to handle.
Comes with template for calculating in different units.
Yarn count can be calculated directly in Ne, Nm, worsted & linen etc.

Technical Specifications:
Weight of rider 0.115 g
No of Rider supplied 2 Nos

Template for direct calculating count in Ne. Nm, Nw

& linen.
RANGER APPAREL EXPORT APPAREL PVT. LTDRANGER
CROCK METER
INSTRUCTIONMANUAL

Introduction
The Apparatus is used for testing the Color fastness of Textiles in the form of Yarn,
Fabric whether dyed, printed or otherwise colored to crocking i.e. wet rubbing and dry
rubbing. In this test, a finger of cylindrical shape, covered with Standard White fabric
(Crocking Cloth) is rubbed against the Test specimen under a fixed load of 9 N.

Testing Procedure
The Crock meter consists a base frame on which the fabric Yarn
or are mounted
on the top of the frame are holded by clamp.
A moving finger is fixed to with
an arm a rotating handle. By rotating the handle the
finger moves To and Fro to a fixed distance set as per that standards.
The finger is given load of 9N
a by an extra mass provided on the moving arm.
Mechanical counter provided for counting the number of strokes with Re-settable
facility.
The base of the apparatus is nicely finished by powder coating, others parts are
Nical plated to give a corrosion-resistant fine finish.
Accessories
o Fabric Clip - 2 NoS

O Water emery
600
(160x40) - 1 No.

Maintenance
This instrument does not any special maintenance procedure. Always kept the instrument
in dust free environment.
 WATER ABSORBENCY TESTING PROCEDURE

Testing method
AATCC-79

Requirement
1. Burette (10ml capacity) with stand
2. Fabric clamp
3. Beaker
4. Specimen
5. Distilled water

Technical instruction
1. Specimen size should be 20cm x 20cm
2. Distance between the tip of burette to the surface of fabric is 10mm
3. Burette capacity is 1Oml (not applicable if more than 10ml)
4. To ensure the fabric to be flat without waves.
5. Distilled water is necessary. Do not use normal water

PROCEDURE
1. Specimen need to be clamped over the beaker without any
wrinkles and waves. It Should be even
2. One drop of water applied on the fabric surface, At the same
time stop watch must be started
3. Need to notice the fall or observation of water by the fabric
until the disappearance of reflection which means the water
just spread flatly.
4. In this time, need to stop the watch and notice the time. same
will be continued for the next trails.

Burette (distance from the tip to

10 mm)
d tabric surface:

Test fabric (20 x 20 cm)

RANGER APPAREL EXPORT APPAREL PVT.LTDRaNGER
User Manual
Of
Button Snap Pull Tester
Introduction:
Oracle Button Snap Pull Tester is very useful equipment to measure separation force of

button. press buttons & snaps from garments. It can also be used to check zip lock strength.

Top Handle

Gauge

Lifting Handle
Jaw

Round Knob
Lower Grasp

Equipment Detail:
Button Snap Pull Tester is completely made of mild steel with duly chrome plated.

IMADA force Measuring gauge, Made In Japan, up to 30 kg capacity is used for

measuring accurate strength of buttons. Specially designed three jaws are supplied with the
cquipment to grip different type of buttons& snaps flawlessly with no slippage. Special Vice
with adjustable location for easy alignment.15 Ibs calibration weight is also supplied to
verify the gauge performance on regular basis.
List of Items Supplied with the equipment:

.MainUnit No

Jaw Big No

Jaw Medium No

.JawSmall I No

.Calibration Weight No

User's Manual I No

Operating Procedure
Place the sample underthe lower grasp as shown in the figure.

.Rotate the round knob to tighten the sample under lowergrasp.

.Grip the button with appropriate jaw as shown in the figure.

Set the gauge at 0' Mark. Setthe gauge in °On' po sition with the switch given in
the left side of the gauge.

Lift the lifting handle up ward to check the load required to separate the button.

See the reading in the gauge.

Technical Specifications:

Capacity 30 Ke

Sensitivity 250 g
No of Jaws Three

Gauge Type Analog

Calibration Weight 15 Ibs
 BUTTON/SNAP PULL TESTING MACHINE

Make: Saf Guard

Parameters: Range 0-30Kgf

Procedure:

Snappulltest procedure
15 lbs weight will be applied in machine to calibrate the snap pull testing machine.
Place the snapped garment in constant clamping and hold the fabric with lower fabric clamp.
Place the Upper universal grip/ Upper stud griper and lock the tool with machine.

Upper universal grip/ Upper stud griper will hold the snap button in lower fabric clamp.
.Make the dial zero point and swatch on the dial reading button.
Rotate the slow movement handle at right side bottom of the machine.
As per ASTM 5035 (MOD) standard 15lbs will the slow movement handle and
move once 15lbs will
reach in dial stop rotate the handle and hold 10 seconds at same lbs.
Reset the slow movement handle and remove the snap button from the machine and observe the
snap
and fabric quality (like snap button or fabric damage).
Record the reading in snap pull strength report as shown in the dial.

TTF reading procedure for snap

Place the snapped garment in constant clamping and hold the fabric with lower fabric clamp.
Place theUpper universal grip/ Upper stud griper and lock the tool with machine.
Upper universal grip/ Upper stud griper will hold the snap button in lower fabric
clamp.
Make the dial zero point and swatch on the dial reading button.
Left the handle at right side top of the machine till breakage of the snap button or snap button
attached fabric.
Remove the snap button or snap button attached fabric from the machine.
Record the TTF
(Test to failure) reading in snap pull strength report as shown in the dial.
Button pulltest procedure

15 lbs weight will be applied in machine to calibrate the button pull testing machine.

Place the buttoned garment in constant clamping and hold the falbric with lower fabric clamp.

Place the Upper grasp button grip and lock the tool with machine.

Upper grasp button grip will hold the button in lower fabric clamp.

Make the dial zero point and swatch on the dial reading button.

Rotate the slow movement handle at right side bottom of the mac

A s per ASTM 5035 (MOD) standard 15lbs will move the slow movement handle and once 15lbs will
reach in dial stop rotate the handile and hold 10 seconds at same lbs.

Reset the slow movement handle and remove the button from the machine and observe the button,

thread and fabric quality (like button broken, thread breakage or fabric damage).

Record the reading in button pull strength report as shown in the dial.

TF reading procedure for button

Place the buttoned garment in constant clamping and hold the fabric with lower fabric clamp.

Place the Upper grasp button grip and lock the tool with machine.

Upper grasp button grip will hold the button in lower fabric clamp.
Make the dial zero point and swatch on the dial reading button.

Left the handle at right side top of the machine till breakage of the button or button attached fabric.

Remove the button or button attached fabric from the machine.

Record the TTF (Test to failure) reading in button pull strength report as shown in the dial.

Standards:

Snap button pull strength for men, women's and children garment is 15Lbs.

Button pull strength for men, women's and children garment is 15Lbs.

Reference
As per ASTM 5035 (MOD)
RANGER APPAREL EXPORT APPAREL PVT. LTDRANcER
User Manual
Of
TEAR STRENGTH TESTER i5-6.4 kg capacity

Introduction:
The Tear Strength Tester of fabrics, Plastic films, or other similar materials is determined by
measurement of the work done in tearing through a fixed length of the test specimen using the
Elmendorf tear tester.

Equipment Details:
Elmendorf Tear Tester consist of a sector pendulum pivoted on anti-friction ball bearing on
vertical bracket fived on a rigid metallic base. The test specimen in shape of a rectangular piece is
held between two jaws, one of which is mounted on the pendulum and the other is mounted on the
Vertical Arm. The Jaws eclamps are mounted in such a manner that their holding faces are aligned
with each other when the pendulum is locked in its raised position.

An adjustable knife is also mounted on the Vertical Arm. It is centered between the two jaws for

initial slit in the test The is released by lifting a brake release lever.
making specimen. pendulum
This action causes t:e test specimen to tear right through. The tearing strength is indicated on a

calibrated scale fitted o. the pendulum by a fine pointer. A set of calibrated check weights are

Supplied with the tester for verification calibration of the seale at 1600, 3200 and 6400 gms

capacities,

In orde incrce se the capacity of the tester, from 1600 gms augmenting weights of 3200 gms d

5400 gmsr supplied as standard accessories.

time.
Nute For testing of low strength materials, multiple specimens may be mounted at the same
RANGER APPAREL EXPORT APPAREL PVT, LTDRANGER

Technical Details:
Capacity 1600gms, 3200gms & 6400gmns
Clamping surfaces of each clamp 35.5mm length x 15.5mm width
Distance betwecn clamps
2.50+0.25mm
Tearing Distance 43+0.15mm
Slit Size
200.2mm
Scale Reading 0 to 100% of range (Least count: 1%)
Calibration check weight At 1600gms, 3200gms & 6400gms
Overall Dimension of the unit 520 (L) x 255 (W) x 560 (H) mm.

Net weight of the unit

28kgs.
Balancing weight main pendulum 50 x 50 x 2.5 mm

Main pendulum 240 (R) x 5 (T) mm

Template Size As per ASTM standard.

Related Standards:
BS 4153, 4253, 3424, 4468

ASTM D 1424

DIN 53862

M&S P 29

BSEN IS0 13937

Newt 17