0327-0328_F37-002_cENG cENG 2nd

*The heat resistance temperatures shown in the tables are for the spring wire
Springs material. The data are obtained in room temperature. Allowable load and durability
may decrease depending on the various conditions under higher temperature.
Overview
* The load range shown is for material SWP-A.
* Values for the Tension Springs Configurable Type are for coil length =50.
Part Number
Load* N{kgf} QTension Springs
Type Features Type Material
SWP-A SUS304-WPB min. max.
Extra Light Load P.329 AWA P.329 AUA 0.69{0.07} 19.6{2.0} Load P[N] = Initial Tension Pi[N] + (Spring Constant k[N/mm] x Deflection F[mm])
Light Load P.329 AWY BWY P.329 AUY BUY 1.86{0.19} 78.45{8.0}
Tension Springs

Light Medium Load P.330 AWU BWU P.330 AUU BUU 2.45{0.25} 98.07{10.0} • MISUMI
 Tension Springs (except for Specified Types) are standardized to maintain the maximum load constantly to the same diameter.
Medium Load P.330 AWS BWS P.330 AUS BUSS 3.53{0.36} 225.55{23.01} Produced based on the maximum load value, the initial tension and spring constant are reference values.
Medium Heavy Load P.331 AWF - - 6.47{0.66} 83.36{8.5} • Use
 the springs within the range of the allowable deflection F max.(mm). Using at higher than the allowable deflection values may cause
Heavy Load P.331 AWT BWT P.331 AUT BUT 8.8{0.9} 430.51{43.91} deformation or failure after a few uses. Also, do not extend tension springs more than its allowable deflection during the installation.
*Heat Resistant Temperature:
Configurable P.332 WFSP BWFSP P.332 UFSP BUFSP 2.37{0.2} 156{15.9} EFor Tension Springs durability can not be shown because stress concentration may occur depending on the hook installation. It is
SWP-A 0~120°C, SUS304-WPB 0~180°C Long, No Hook P.333 LWS P.333 LUS - - recommended to use the springs within 70 % of allowable deflection F max.(mm).
Part Number Max. Allowable Deflection • It is recommended to use the tension springs (AW#, BW#, AWFM, WFSP, LWS, LWSH) under ambient temperature (at 40°C or less).
Load* N{kgf}
Type Features Type Material % Load value attenuates when tension springs are used in temperature higher than 40°C, although it depends on other conditions.
SWP-A SUS304-WPB (Standard Usage Count) min. max.
P.343 WY P.353 UV, UY 75 (1 Million Times) 0.18{0.018} 1.75{0.179} QRound Coil Springs / Irregular Shaped Coil Springs
P.344 WR P.353 UR 60 (1 Million Times) 0.9{0.09} 23.5{2.4}
P.345 WF P.354 UF 45 (1 Million Times) 1.1{0.11} 35.3{3.6}
P.346 WL P.355 UL 40 (1 Million Times) 0.98{0.1} 117.7{12} Load P[N] = (Spring Constant k[N/mm] x Deflection F[mm])
O.D. Referenced
P.347 WT P.356 UTT 40 (1 Million Times) 2.9{0.3} 125.5{12.8}
Round Coil Springs

P.348 WM P.357 UM 28 ~ 35 (1 Million Times) 3.4{0.35} 171.6{17.5} • MISUMI

 Round Coil Springs are standardized to maintain the spring constant constantly to the same diameter. The tolerance of spring
P.349 WH P.358 UH 20 ~ 30 (1 Million Times) 4.4{0.45} 441.3{45} constant is ±10%.
(Stainless Steel) P.350 WB P.359 UBB 25 (1 Million Times) 5.9{0.6} 735.5{75} Irregular shaped coil springs are standardized to maintain the maximum load constantly to the same diameter. The load tolerances vary
- - P.351 VUR 60 (1 Million Times) 2.65{0.27} 17.64{1.8} depending on the spring type, please refer to the respective page.
- - P.351 VUF 45 (1 Million Times) 3.33{0.34} 22.05{2.25} • Use
 the springs within the range of the allowable deflection F max.(mm). Using at higher than the allowable deflection values may cause
I.D. Referenced
- - P.352 VUL 40 (1 Million Times) 5.88{0.60} 39.20{4.00} deformation or failure.
- - P.352 VUM 35 (1 Million Times) 15.39{1.57} 102.90{10.50} • The values of solid length are for reference only. Using it compressed to the solid length may cause deformation or break after a few uses.
O.D. Referenced P.360 FWR P.360 FUR 60 (1 Million Times) 2.5{0.25} 55.2{5.63} • Round
 Coil Springs are manufactured based on the following diametric tolerance priorities given. I.D. Selectable Type: Inner diameter
*Heat Resistant Temperature:
L Dimension P.360 FWF P.360 FUF 50 (1 Million Times) 4.5{0.46} 100.0{10.2} tolerance prioritized / O.D. Selectable Type: Outer diameter tolerance prioritized.
Configurable
SWP-A 120°C, SUS304-WPB 180°C P.360 FWT P.360 FUT 40 (1 Million Times) 7.1{0.73} 128.0{13.1} For inner/outer diameter tolerances of irregular shaped coil springs, refer to the respective pages.
EIt is recommended to use the round coil springs and irregular shaped coil springs under ambient temperature (40˚C or less). Load value
Type Flat Springs Torsion Springs Constant Force Springs
attenuates when tension springs are used in temperature higher than 40°C, although it depends on other conditions. (Heat resistant
springs are listed on "Standard Components for Plastic Mold".)
• Irregular
 Shaped Coil Springs are listed on "Standard Components for Press Dies" and "Standard Components for Plastic Mold". (Large
Features Dia. Sizes are also available.)

QRelationship between Spring Length L and Load P

Type Straight One-Point-Bend Two-Point-Bend Arm Angle 90° Arm Angle 135° Arm Angle 180° Main Body Bracket • Tension Springs • Round Coil Springs
Load P (N) Load P (N)
Material SUS304-CSP SUS304-WPB SUS301EH SUS430
Part Number IBN IBNS IBNW UA90# UA135# UA180# CFS CFSB
Max. Allowable Load Max. Allowable Load
Page P.339 P.340 P.341
P max. P max.
Part Number Max. Allowable Deflection Load N{kgf}
Type Features Material Color %
Oil tempered wires for springs (Standard Usage Count) min. max.
Pastel 65 (1 Million Times) 29.4{3} 392.3{40}
P.361 SWY green 70 (300,000 Times) 31.7{3.2} 425.6{43}
60 (1 Million Times) 68.6{7} 588.4{60}
P.362 SWU Light Blue
65 (300,000 Times) 73.9{7.5} 637.4{65}
Initial Tension
Irregular Shaped Coil Springs

50 (1 Million Times) 78.5{8} 1323.9{135} Pi

P.363 SWR Ivory
55 (300,000 Times) 87.2{8.8} 1456.3{148}
40 (1 Million Times) 87.2{8.8} 1569.1{160}
* Heat Resistant Temperature: Oil tempered wires for springs 200°C P.364 SWS Orange
45 (300,000 Times) 97.1{10} 1765.2{180} Spring Length L Spring Length L
0 0 F max. (mm)
40 (1 Million Times) 47.1{4.8} 3138.1{320} Free Length L0 F max. L max. (mm)
L min. Free Length L0
P.365 SWF Yellow
50 (300,000 Times) 58.8{6} 3922.6{400} L min.=L0-Fmax.
32 (1 Million Times) 62.8{6.4} 657.0{67} Use within this range.
P.367 SWL Blue
40 (300,000 Times) 78.5{8} 823.8{84}
Free Length L0 Free Length L0
25.6 (1 Million Times) 78.5{8} 980.7{100}
P.368 SWM Red
32 (300,000 Times) 98.1{10} 1225.8{125} L. min. under max. L. min. under max.
19.2 (1 Million Times) 109.8{11.2} 1471.0{150} allowable deflection allowable deflection
P.369 SWH Green
24 (300,000 Times) 137.4{14} 1833.8{187} Use within this range.
16 (1 Million Times) 141.2{14.4} 1922.1{196}
* Heat Resistant Temperature: Oil tempered wires for springs 200°C P.370 SWB Brown
20 (300,000 Times) 176.5{18} 2402.6{245}
1N=0.101972kgf 1deg=1°(Angle)

2 -327 2 -328