KENYA COAST NATIONAL POLYTECHNIC

MARINE BLASTING LEVEL 3

ASSESSMENT TOOLS

Page 1 of 26
 MARINE BLAASTING LEVEL 3

CANDIDATE’S ORAL ASSESSMENT

Page 2 of 26
Qualification Code : ………………
Qualification : Marine Blasting level 3
Unit Code : KCNP/MAE/CU/TD/CO/11/3/A
Unit of Competency : Basic Engineering Drawing

ORAL ASSESSMENT (20 MARKS)

INSTRUCTIONS TO CANDIDATE
1. This assessment requires you to demonstrate competence against unit of competency:
Apply Basic engineering drawing skills
2. The assessor will ask you Ten (10) questions.
3. You are required to provide short verbal answers.
4. Time allocated is 30 minutes.
5. Your responses will be recorded by the audio-visual means.

Page 3 of 26
 KENYA COAST NATIONAL POLYTECHNIC

Qualification Code : ………….

Qualification : Marine Blasting level 3
Unit Code : KCNP/MAE/CU/TD/CO/11/3/A

Unit of Competency : Basic Engineering Drawing

ORAL ASSESSMENT ASSESSOR’S GUIDE

INSTRUCTIONS TO THE ASSESSOR

1. Ask the candidate each of the following questions.
2. Record the assessment process via audio-visual means.
3. Record the marks for each question in the candidate’s score column provided.
4. Time allocated is 30 minutes

Page 4 of 26
Candidate’s Name: _______________________________________________________

Candidate’s Registration Code: ____________________________________________

Assessor’s Name: _______________________________________________________

Assessor’s Registration
Code:__________________________________________________

Venue of Assessment: _______________________________________________

Date of Assessment: ___________________________________________________

S/ Question Model answers Maximu Candidate’ Remarks

No. (These are suggested m s
answers to act as Marks Score
guidelines)
1 What are the  Front 3
three views  End
used in  plan
orthographic
projection?

2 What is a  Is a plane figure 1

circle? bounded by one
continue curved
line which is
equidistant from
Page 5 of 26
 the Centre
3 What is an  Is a regular 1
octagon? geometric figure
that has eight
equal sides
4 Which line  Centre line 1
shows mid-
point of an
object?

5 What is  It is a drawing 1
sketch? which is not
dawn to a
standard scale
6 What is  It is means of 2
orthographic producing a true
projection? shape and
dimensions of all
details of a three
dimensional
object on a two
dimensional
plane surface
7 What is a  It is a datum line 1
reference line for a drawing in
in drawing? which an
drawing object
should be located
8 Name four  They are thin 4
features of a  Continues
dimensional  Should have
Page 6 of 26
 line? sharp filled-in
arrow-head of
4mm long
 Placed outside
the outline of the
component

9 What is an  It is a drawing 2
isometric whose vertical
projection? lines are drawn
vertically and
horizontal lines
drawn at an
angle of 300 to
horizontal
10 What are four  T-square 4
drawing  Set squares
instruments  Ruler
used for  pencil
making lines?

TOTAL MARKS 0

Comments by Assessor

Assessor’s Signature Date

------------------------------ -----------------------------

Page 7 of 26
 MARINE BLASTING LEVEL 3

CADIDATE’S WRITTEN ASSESSMENT

Page 8 of 26
 KENYA COAST NATIONAL POLYTECHNIC CURRICULUM

Qualification Code :
Qualification : Marine welding Level 4
Unit Code : KCNP/MAE/CU/TD/CO/11/3/A

Unit of Competency : Basic Engineering Drawing

WRITTEN ASSESSMENT

Candidate’s Name :

Registration Code:

Venue of
Assessment:

Date of Assessment:

INSTRUCTIONS TO CANDIDATE
1. This assessment requires you to demonstrate competence against unit of
competency: Apply Basic Engineering Drawing skills

Page 9 of 26
2. You have Three hours and thirty minutes (3hr 30 Min) to attempt all the
questions.
3. Marks for each question are indicated in brackets ( ).
4. This paper consists of two (2) sections: A and B
5. The following tools and materials will be required during the assessment:

 A T-square

 Drawing board

 Set squares

 Engineering drawing set

 Masking tape

 Pencils(2H and HB preferably steadler)

 Pure white rubber

 A drawing paper

Page 10 of 26
 SECTION A (20 MARKS)
Attempt all the questions in this section
Write down your answers in the spaces provided

1. When constructing given object, the drawings must the standards. What are the
three requirements of an engineering drawing? (3 marks)
…………………………………………………………………………………………
…………………………………………………………………………………………
2. As a technician, you are required to produce a quality engineering drawing.
Which are some of the paper preparation to ensure to achieve quality drawing? (3marks)
…………………………………………………………………………………………
…………………………………………………………………………………………

3. You are to interpret a drawing for a component for welding, what are some of
the four types of drawing lines that may be incorporated? (4marks)
………………………………………………………………………………………………
……………………………………………………………………………………

4. After carrying out a construction, drawing tools should be maintained and safely kept.
What three care and maintenance practises to ensure on a drawing instruments (3marks)
………………………………………………………………………………………………
………………………………………………………………………………………………
………………………………………………………………………………………………
………………………………………………………………………………………………
………………………………………………………………………………………………
………………………………………………………………………………………………

Page 11 of 26
5. You have been consulted by an organization on the workshop work holding devices.
Draw by se of a freehand sketch a bench vice in good proportion (9marks)

6. Draw four common lines used in technical engineering drawing. (4marks)

………………………………………………………………………………………………
………………………………………………………………………………………………
………………………………………………………………………………………………
………………………………………………………………………………………………
………………………………………………………………………………………………

Page 12 of 26
 SECTION B (30 MARKS)
Attempt all the questions in this section
Write down your answers in the drawing paper provided

7. Construct a regular heptagon of side length 30mm in a circle. Show all the construction
work. (6marks)

8. As an engineering technician, you are to blend two circles of centers A and B to achieve a
common curve touching the two circles. If the radii are r=15mm and R= 25mm with a
distance AB = 60mm. Perform the construction of the curve. (6marks)

9. Figure b shows a pictorial view of a spring hanger bracket. Using third angle projection
draw the front view from point A and plan in full size. (9marks)

Fig. b.

Page 13 of 26
10. Construct a circle such that it touches a given circle of radius, r = 15mm (4marks)

11. Figure c. shows the outline of two circles. Draw the blank, full size, showing clearly the
constructions arcs and curves. (7marks)

Fig c.

Page 14 of 26
 KENYA COAST NATIONAL POLYTECHNIC CURRICULUM

Qualification Code :
Qualification : Marine welding Level 4
Unit Code : KCNP/MAE/CU/TD/CO/11/3/A

Unit of Competency : Basic Engineering Drawing

WRITTEN ASSESSMENT ASSESSOR’S GUIDE

SECTION A (20 MARKS)

Note to Assessor: These are suggested answers to act as guidelines.

12. When constructing given object, the drawings must the standards. What are the
three requirements of an engineering drawing? (3 marks)
 Technique
 Accuracy
 Neatness
13. As a technician, you are required to produce a quality engineering drawing.
Which are some of the paper preparation to ensure to achieve quality drawing? (3marks)
 Appropriate use of instrument
 Clear dimensioning

Page 15 of 26
  A clear scale
 Clear tittle block
14. You are to interpret a drawing for welding, what are some of the four types of
line that may be incorporated? (4marks)
 hidden detail line
 Centre line
 cutting plane line
 thin continuous line
 medium continuous line
 long break line

15. After carrying out a construction, drawing tools should be maintained and
safely kept. What three care and maintenance practises to ensure on a drawing
instruments (3marks)
 Drawing instruments should be carefully handled at all times to avoid damage.
 Instruments should be stored flat in clean dry compartments in drawers or
boxes which are dust proof.
 Instruments should be wiped clean before and after use.
 Instruments should be properly used for their proper purpose

16. You have been consulted by an organization on the workshop work holding devices. Draw
by se of a freehand sketch a bench vice in good proportion (9marks)

Page 16 of 26
 fig.a

17. Draw four common lines used in technical engineering drawing. (4marks)

Page 17 of 26
Page 18 of 26
 SECTION B (30 MARKS)

Note to Assessor: These are suggested answers to act as guidelines.

1. a) Construct a regular heptagon of side length 30mm in a circle. show all the construction
work. (6marks)
Solution.

2. As an engineering technician, you are to blend two circles of centers A and B to achieve a
common curve touching the two circles. If the radii are r=15mm and R= 25mm with a distance
AB = 60mm. Perform the construction of the curve. (6marks)

Solution.

Page 19 of 26
3. Figure b shows a pictorial view of a spring hanger bracket. Using third angle projection draw
the front view from point A and End view in full size.
(8marks)

Page 20 of 26
Fig. b.

Page 21 of 26
Solution

Page 22 of 26
4. Construct a circle such that it touches a given circle of radius, r = 15mm (5marks)

Solution.

5. Figure c. shows the outline curves of two circles. Draw the blank, full size, showing clearly
the constructions arcs and curves. (8marks)

Page 23 of 26
Page 24 of 26
 Candidate’s Name & Registration Code

Assessor’s Name & Registration Code

Venue of Assessment

Date of Assessment

Marks Marks
Question
Available Obtained
ORAL ASSESSMENT 20

SECTION A 20
Question 1 to 6

SECTION B (STRUCTURED QUESTIONS)

Question 7 5

Question 8 5

Question 9 9

Question 10 4

Question 11 7

SUB-TOTAL SECTION B 30

TOTAL MARKS 70

The candidate was found to be: Competent Not yet competent

(The candidate is competent if s/he gets 50% or higher)

Page 25 of 26
 Comments by Assessor:

Assessor’s Signature Date

------------------------------ -----------------------------

Page 26 of 26