Kayak Design Terms | Guillemot Kayaks

http://www.guillemot-kayaks.com/guillemot/information/kayak_design/...

Home

Catalog

Information

Community

About Us

Contact Us

Search

Boat Design Browser

Custom Built Boats

Kayak & Boat Kits

Small Boat Plans

Events

Classes

YOU ARE HERE

Information / Kayak Design / Kayak Design Terms

INFORMATION
Products and Services FAQ Kayak Design Varieties of Kayaks Boat Speed How a New Boat is Designed How a Paddle Works Kayak Design Terms Kayak Stability Tracking and Maneuverability Kayak Building Kayaking Technique Kayaking Trips Kayak Building Bibliography Water Line Beam (in) Water Line Length (ft) Also known as Length Water Line or Load Water Line (LWL The length of LWL). LWL the boat measured at the waterline. Used to determine "hull speed". In general boats with longer LWLs will be more efficient at high speeds. In other words long LWLs general make boats faster. As the term "Load Water Line" implies this is the length of the waterline when the boat is loaded the design displacement. Also known as Beam Water Line (BWL The width of the boat BWL). BWL measured at the waterline. This is a primary determinant of initial stability. Over All Width (in) Over All Length (ft) A description of boat design terms and how they relate to boat performance.

SHOPPING CART

Kayak Design Terms

View your shopping cart.

COMMUNITY
Particulars Just a fancy term for the Click on image for measurements and characteristics of a enlargement boat. Also known as Length Over All (LOA LOA). LOA The total length of the kayak from bow to stern Also known as Beam Over All (BOA BOA). BOA The width at the widest point of the boat. Nick's Blog Gallery Kayak Forum Whats New Log In

UPCOMING EVENTS
Kayak Paddle Making Demo @ Lie Nielsen Hand Tool Event (7 days) (Event) Build a High Performance Sea Kayak at CVSW (85 days) (Event)

more

Request a Printed Catalog or Design Water Line Displacement (lbs) The Design Water Line (DWL determines the total amount of DWL) DWL weight the boat was designed to carry. This is a some what arbitrary number. The boat can carry more or less, but the other particulars are only completely accurate when the combined weight of the boat, paddler and the gear it is carrying is the same as the DWL displacement. How far below the waterline the boat reaches. This does not include rudders or retractable skegs. Print your Own

Draft (in)

Wetted Area (sq. ft)

The surface area of the part of the boat that is under water. Lower wetted area means less frictional drag.

Waterpl. Area (sq. ft)

The area of the water plane. The waterplane defined by the waterline outline.

Total surface area (sq. ft)

The total surface area of the skin of the boat. You can get an approximation of the weight of the bare boat by multiplying by the density of the wood strip and fiberglass layupyou are using. A good starting point is 0.7 pounds per square foot for a typical 1/4" layup with 6 ounce glass.

1 de 3

21/10/2011 08:38

Kayak Design Terms | Guillemot Kayaks

http://www.guillemot-kayaks.com/guillemot/information/kayak_design/...

Approximate Bare Boat Weight (lbs) Volume (cu ft) Volume (Gallons)

The weight of the boat before adding seats, hatches, rudders or any other outfitting. This is approximated by multiplying the Total areaabove by 0.7. and assumes 1/4" western red cedar surface area strips with 6 ounce cloth. The total volume of the kayak. The volume of water that the boat would displace if it were totally submerged. Same as above in gallons.

Prismatic Coeff. Prismatic Coefficient (Cp or Cp) Cp Longitudinal Prismatic Coefficient: (The displacement volume) divided by (the volume of a prism equal in length to the LWL whose cross sectional area equals the Midship section area) This is a rough measurement of the "fineness" of the boat shape. A boat with a "fine" shape has quite sharp ends. It is used to estimate drag. The typical range is roughly 0.5 to 0.7. Higher numbers tend to be more efficient at higher speeds and lower number more efficient at lower speeds. The prismatic coefficient was originally developed as term for hull design analysis by Admiral David W Taylor in 1943. Block Coeff. Block Coefficient (Cb Cb) Cb (the displaced volume) divided by (LWL * BWL * Draft) This a rough measurement of how "V" shaped the bottom of the boat. It is useful in determining how well a boat tracks Midship Area Coeff. Midship Coefficient (Cm Cm) Cm (The area of the section at midship) divided by (BWL * Draft)

Waterpl. Area Coeff.

The area of the waterplane divided by the length and width of the boat at the waterline.

Lateral Plane Coeff.

The lateral plane is what you see below the waterline when looking at the boat from the side. This coefficient is the area of the lateral plane divided by the LWL times the Draft. The fore and aft location of the Center of Buoyancy relative to the middle of the boat. Here it tells you how far behind the middle of the boat the Center of Buoyancy is. Often abbreviated as: B , CB or COB CB, COB. The location of the geometric center of the waterplane area relative to the middle of the boat. This is where you would add more weight for the boat to sink straight down. Often abbreviated as:F, CF COF or LCF LCF. F CF, COF, The location of the geometric center of the lateral plane relative to the middle of the boat.

Longitudinal Center of Buoyancy behind Amidship (in) Longitudinal Center of Flotation behind Amidship (in) Center Lateral Area behind Amidship (in)

Sinkage (lbs/in) An approximation of how much weight you would have to add to sink the boat another inch. It will generally require more weight to get a full inch, but if you want to go up or down 1/10th inch, one 1/10th of the Sinkage added or subtracted will be pretty close. Moments to change trim 1 inch (lbft) The amount of torque required to push the bow or stern into the water about 1 inch. This is an indications of how quickly the boat will rise over

2 de 3

21/10/2011 08:38

Kayak Design Terms | Guillemot Kayaks

http://www.guillemot-kayaks.com/guillemot/information/kayak_design/...

waves. Righting Moment at 1 degree (lbft) How much torque is required to tip the boat a small amount. An indication of initial stability.

The VCG is used to calculate the Vertical Center of Gravity above "Moment to change Trim" and the "Righting Moment" above and is DWL (in) important for determining stability. Most of the data on these pages assume a VCG that is 10.5 inches above the bottom of the boat.

How a Paddle Works

up

Kayak Stability

Tags

Design

2005-2011 Guillemot Kayaks. All rights reserved.

3 de 3

21/10/2011 08:38