Scribd Logo
Upload

Welcome to Scribd!

  • 18 views

    Hempel Paints

    Uploaded by

    ahmadqammaz.89
    sigma TDS 3

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Hempel Paints

    Uploaded by

    ahmadqammaz.89
    18 views4 pages
    sigma TDS 3

    Original Title

    01. Hempel Paints

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    sigma TDS 3

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    18 views4 pages

    Hempel Paints

    Uploaded by

    ahmadqammaz.89
    sigma TDS 3

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 4

    Product Data

    HEMPINOL HB 10270

    Description: HEMPINOL HB 10270 is a physically drying, high build, bituminous coating. It is flexible, water
    resistant and rust preventing.

    Recommended use: As an economical corrosion protection of interior and exterior steel and concrete substrate in
    moderately corrosive environment, not exposed to direct sunlight. Well suited for steel and
    concrete surfaces buried in subsoil conditions.

    Certificates/approvals: Approved under Saudi Aramco’s Engineering Standards APCS 10 and APCS 23.

    Availability: Not included in Group Assortment. Local availability subject to confirmation.

    Physical constants:

    Shade nos/Colours: 19990 / Black


    Finish: Flat
    Volume solids, %: 62 ± 1
    Theoretical spreading rate: 1.4 m²/litre [55 sq.ft/US gallon] – 450 micron/18 mils
    Flash point: 38°C [100°F]
    Specific gravity: 1.2 kg/litre [10 lbs/US gallon]
    Surface-dry: 12 hours (approx.), 20°C/68°F

    The physical constants stated are nominal data according to the Hempel Group's approved formulas.

    Application details:

    Application method: Airless spray / Roller/Brush (touch-up)


    Thinner (max.vol.): 08080 (5%) / 08230 (5%)
    Nozzle orifice: 0.021"- 0.031"
    Nozzle pressure: 200 bar [2900 psi]
    (Airless spray data are indicative and subject to adjustment)
    Cleaning of tools: HEMPEL'S THINNER 08080
    Indicated film thickness, dry: 450 micron/18 mils (see REMARKS overleaf)
    Indicated film thickness, wet: 725 micron/29 mils
    Overcoat interval, min: When dry
    Overcoat interval, max: None (See REMARKS overleaf)

    Safety: Handle with care. Before and during use, observe all safety labels on packaging and
    paint containers, consult Hempel Material Safety Data Sheets and follow all local
    or national safety regulations.

    Issued: October 2016 Page: 1/2


    Product Data
    HEMPINOL HB 10270

    SURFACE PREPARATION: New steel: Abrasive blasting to minimum Sa 2 or mechanical cleaning to St 3. For temporary
    protection, if required, use a suitable shopprimer. All damage of shopprimer and contamination
    from storage and fabrication should be thoroughly cleaned prior to final painting. For repair and
    touch-up, use HEMPINOL HB 10270.
    Concrete: Remove slip agent and other possible contaminants by emulsion washing followed
    by high pressure hosing with fresh water. Remove scum layer and loose matter to a hard,
    rough and uniform surface, preferably by abrasive blasting, possibly by other mechanical
    treatment or acid etching. Seal surface with suitable sealer, e.g. HEMPADUR SEALER 05990,
    or apply HEMPINOL HB 10270 directly on concrete, diluted 10-20% with HEMPEL’S THINNER
    08080.
    Maintenance: Remove oil and grease, etc. thoroughly with suitable detergent. Remove salt
    and other contaminants by (high pressure) fresh water cleaning. Remove all rust and loose
    material by abrasive blasting, power tool cleaning or water jetting. Dust off residues and allow
    the surface to dry. Touch-up to full film thickness.

    APPLICATION CONDITIONS: As dictated by normal good painting practice. In confined spaces, provide adequate ventilation
    during application and drying.

    PRECEDING COAT: None or according to specification.

    SUBSEQUENT COAT: None.

    REMARKS:

    Film thicknesses/thinning: May be specified in another film thickness than indicated depending on purpose and area of
    use. This will alter spreading rate and may influence drying time and recoating interval. Normal
    range is 350-550 microns/14-22 mils.

    Recoating: No maximum recoating interval, but before recoating after exposure in contaminated
    environment, clean the surface thoroughly by high pressure fresh water hosing and allow to
    dry.

    Note: HEMPINOL HB 10270 is for professional use only.

    Issued by: HEMPEL PAINTS (SAUDI ARABIA) W.L.L. – 1027019990

    This Product Data Sheet supersedes those previously issued.


    For explanations, definitions and scope, see “Explanatory Notes” available on www.hempel.com. Data, specifications, directions and recommendations given in this data sheet
    represent only test results or experience obtained under controlled or specially defined circumstances. Their accuracy, completeness or appropriateness under the actual conditions
    of any intended use of the Products herein must be determined exclusively by the Buyer and/or User.
    The Products are supplied and all technical assistance is given subject to HEMPEL’s GENERAL CONDITIONS OF SALES, DELIVERY AND SERVICE, unless otherwise expressly agreed
    in writing. The Manufacturer and Seller disclaim, and Buyer and/or User waive all claims involving, any liability, including but not limited to negligence, except as expressed in said
    GENERAL CONDITIONS for all results, injury or direct or consequential losses or damages arising from the use of the Products as recommended above, on the overleaf or otherwise.
    Product data are subject to change without notice and become void five years from the date of issue.

    Issued: October 2016 Page: 2/2

    You might also like