Scribd
Upload
44 views29 pages

3 - Controller BCP7 Hardware

Domino

Uploaded by

Aldiyansah Pratama1
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
44 views29 pages

3 - Controller BCP7 Hardware

Domino

Uploaded by

Aldiyansah Pratama1
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 29

Controller BCP7

Hardware
Controller BCP7 (D120i / D320i / D620i)
 ETX Board
 DIB (D-Series Interface Board)
 User I/O (Optional)
 Safety Relay
 Main Power Supply
 Laser Power Supply
 Fuses
 Push Button
 Key Switch
Power Adaption Box (60 Watt Laser Only)
 PEB (Power Extension Board)
 Laser Power Contactors
 Laser Power Supply
 Fuses
 Main Switch
Controller BCP7 (D120i / D320i / D620i)
ETX Board

CF-Card

USB

Ethernet connected to
VGA connector the front panel

USB connected to
the front panel

Connection to optional
User I/O
RS232
Connection to optional User I/O

Connection to DIB PC-CMOS Battery


DIB (D-Series Interface Board)
Main Power from Main Switch Socket for ETXB Power from the laser
power supply

Main voltage to
Main Power Supply

Main voltage to
Laser Power Supply

Connectors for the


conduit of the laser
head

Key Switch

24 Volt for CPU-Fan


(not used) Voltages from Main power supply
Safety Relay
24 Volt from PC power supply
Fans (controller) Additional
heat sensor (option) Voltage to optional User I/O
DIB (D-Series Interface Board)

Switched AC power
for Laser Power Supply
(used up to 30 Watt systems)

Switched AC power
for Laser Power Supply
(used for 55 Watt systems)
DIB (D-Series Interface Board)
X7 X28 X23 X59 X3 X6

Interlock 1
Interlock 2
Server Running
Printer Ready
Printer Busy

X4 X2 X29 X58
* Lihat Presentasi Datashet Connector BCP7
User I/O (Optional)

RS232 Cable

User I/O Cable

Ground Cable

Power Cable

User I/O Board


User I/O (Optional)

RS232
User I/O

Power Cable
Ground Cable

User I/O RS232


User I/O (Optional)

Optional User I/O


Every new D-Series controller is prepared for the
User I/O board.

The controller front plate is prepared to fit the


connectors without special tools.
Safety Relay

Power on relay
Interlock 1
Interlock 2
Relay switched on
Reset
Fault
Main Power Supply

Tegangan Out : Tegangan Input :


+5 VDC 100 - 240 VAC/50Hz
+15 / -15 VDC
+24 VDC
Laser Power Supply

Tegangan Input : Tegangan Out :


100 - 240 VAC/50Hz +30 VDC
Fuses
2 X 12,5 A (Main Power Supply) 1 X 10 A (Laser Power Supply)
Push Button

ON/OFF Controller
Key Switch

Laser Start
Standby
Disable
Questions ?
Controller BCP7 (D120i / D320i / D620i)
 ETX Board
 DIB (D-Series Interface Board)
 User I/O (Optional)
 Safety Relay
 Main Power Suply
 Laser Power Suply
 Fuses
 Push Button
 Key Switch
Power Adaption Box (60Watt Laser Only)
Power Adaption Box (60Watt Laser Only)

PEB (Power extension board)


Main Switch

24 Volts Laser Power Supply 1

Laser Power Contactor

24 Volts Laser Power Supply 2 Fuses


PEB (Power Extension Board)

Bypass Relay Fans

24Volt input
from laser power supply 1

Connector for
programming the board

Control Signal for Laser


Power Contactor Laser Power Contactor

AC power to Laser power supply 1


AC power to Laser power supply 2
for future propose Triac‘s
AC Main Power input
AC Main power output
PEB (Power Extension Board)

V9 : Bypass Relay
V10 : Triac enabled

V8 : 24 Volts for Relays present


PEB (Power Extension Board)

V7 : Mains Wave negatif AC

V6 : Mains Wave positif AC


PEB (Power Extension Board)

X11/12 : parallel connected

5V
24V
OK
Warning
Over Temperature

X12 optional used for controller Chain

X11 used for controlling the extension Box (connected to X58)


Laser Power Contactors

Contactor for switching laser power supplies


Laser Power Suply

Tegangan Input : Tegangan Out :


100 - 240 VAC/50Hz / 8,2 A +24 VDC / 25A
(Adjusted to 25,25 V)
Fuses

2x 20 Ampere (Main Power)


Main Switch

Main Switch (AC power)


Need to be switched on before the controller is switched on
Questions ?
Power Adaption Box (60 Watt Laser Only)
 PEB (Power Extension Board)
 Laser Power Contactors
 Laser Power Supply
 Fuses
 Main Switch

You might also like