SCOTT SCALE

USER MANUAL
All rights reserved © 2017 SCOTT Sports SA

Distribution:
SSG (Europe) Distribution Center SA, P.E.D. Zone C1, Rue du Kiell 60, 6790 Aubange, Belgium
v7.0/21052017

WWW.SCOTT-SPORTS.COM W W W. S C O T T- S P O R T S . C O M
SCOTT Sports SA
Route du Crochet 17, CH–1762 Givisiez
Phone: +41 26 460 16 16 | Fax: +41 26 460 16 00
Email: [email protected]
 ••CONTENTS
SCOTT SCALE 3 . . . . . . . . . . . . . . . . . . . . . . . 04
Scale Concept . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 04

Geometry/Technical Data Scale 3 900 . . . . . . . . . . . . . . . . . . . . . 05

WWW.SCOTT-SPORTS.COM
RIDELOC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 06

Basic Set-Up of Forks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 07

SAG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 08
The SCOTT Scale should be adjusted exactly to the individual
rider to achieve maximum saftey and fun while riding. Rebound Fork Set-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 09
SCOTT recommends that all adjustments be carried out by
your local authorized SCOTT dealer. Some basic maintenance Replaceable Rear Dropout . . . . . . . . . . . . . . . . . . . . . . . . . . . . 09
can be done if strictly following the manuals supplied with
this bike.
Brake Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Please contact your authorized SCOTT dealer for advice in order Cable Guides and Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
to avoid any harm and assist you with any questions or technical
problems. BB Standards/FD Mounting Details . . . . . . . . . . . . . . . . . . . . . . . 14

•• IMPORTANT
This manual refers to all 2018 SCOTT Scale carbon bikes and
Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

frames, for all other bikes and frames please refer to the GUARANTEE ON SCOTT BIKES . . . . . . . . . . . . . . .16
correct manual or your authorised SCOTT dealer.
For SCOTT Scale 700 plus please contact your local SCOTT
dealer or refer to 2017 Scale manual and the general SCOTT
manual for more information

| 02 ENGLISH SCALE | BIKE USER MANUAL BIKE USER MANUAL | SCALE ENGLISH 03 |
SCOTT SCALE 3 ••GEOMETRY/TECHNICAL DATA SCALE 3 900
Seatpost Diameter 31.6mm

••SCALE CONCEPT Seattube clamp

Headset
34.9
bearings: 51.9x40x8 45 ° x 45 °/
41.8x30.5x8 45 ° x 45 °
From the Carbon fiber to the manufacturing process to the final result- the new Scale
has been completely redesigned. The result: a new benchmark for race hardtail frames. Fork travel 100mm
The Scale RC 700 SL weighs in at only 849 grams. The incredible lightweight frame BB housing BB PF92
characteristics and two dedicated frame platforms for 1x and 2x drivetrains lift the standard Front derailleur Shimano high direct mount side
of hardtail mountain bikes to a new level. swing (none RC models only)
Additional parts needed
A mix of high-end carbon fibers has been used on all Scale Carbon frames in order to Chainring size 38T max
achieve incredible results. The HMX-SL frame utilizes MR70, YS60 and HR40 Carbon
Max tyre width 2.3/57mm
fibers. HR40 is a strong and light filament which, used together with MR70 fibers, attains
Please note:
unachieved tensile strength values. In order to achieve the set stiffness targets, YS60 layers Tire sizes often vary from brand to
are added into the lay-up. After choosing the Carbon fibers, the engineers are using specific
tools, like FEA software, to map out the carbon lay-up. Thanks to SCOTT's proprietary •• IMPORTANT
Only a bottle with 0.55L capacity will
brand. Ensure the tire clearance is
adequate when replacing your tires!
EvoLap-Technology, different forces can be applied on a virtual model and the frame
have the clearance to fit a small frame
construction is adjusted accordingly.
The SDS2 technology achieves comfort in carbon frames without adding parts or sacrificing
stiffness characteristics. In order to achieve this, the engineers use different tube shapes in
combination with a strategic alignment of the carbon fibers to avoid any undesired flex that
can impair performance.
The Boost standard improves wheel stiffness and allows for increased tire clearance. The
new Scale frame has been developed around the Boost standard in order to maximize the
advantages of the new norm. The three millimeter outboard chain ring adds clearance to the
chainstay area allowing for a significant increase of the chainstay cross-section for both, the
1x and 2x models. This offers more possibilities to find the right position of the rear wheel in
the frame in order to achieve improved structural stiffness.
The new Scale is available in two different versions. The HMX-SL and HMX frames are S M L XL
optimized for 1x drivetrains only and therefore dedicated to race-oriented riders. The HMF
line-up is designed and optimized around a double chain ring setup. These models can, A HEAD TUBE ANGLE 69.5 ° 69.5 ° 69.5 ° 69.5 °
however, accommodate a single chainring configuration. B HEAD TUBE LENGTH 95.0 mm 3.7 in 100.0 mm 3.9 in 115.0 mm 4.5 in 125.0 mm 4.9 in
C TOP TUBE HORIZONTAL 575.0 mm 22.6 in 600.0 mm 23.6 in 625.0 mm 24.6 in 650.0 mm 25.6 in
On the new Scale introduce a specific brake mount adapter which is linked directly to the
D STANDOVER HEIGHT 743.0 mm 29.3 in 774.0 mm 30.5 in 800.0 mm 31.5 in 835.1 mm 32.9 in
chainstay and thru-axle in order to increase stiffness.
E BB OFFSET -58.0 mm -2.3 in -58.0 mm -2.3 in -58.0 mm -2.3 in -58.0 mm -2.3 in

Routing the cables internally avoids bulky external hardware and looks cleaner. Due to the F BB HEIGHT 312.0 mm 12.3 in 312.0 mm 12.3 in 312.0 mm 12.3 in 312.0 mm 12.3 in

improved protection, the cables have a longer lifetime. G WHEEL BASE 1,076.4 mm 42.4 in 1,101.8 mm 43.4 in 1,127.9 mm 44.4 in 1,153.7 mm 45.4 in
H BB CENTER TO TOPTUBE CENTER 325.0 mm 12.8 in 375.0 mm 14.8 in 415.0 mm 16.3 in 465.0 mm 18.3 in
The new Scale chain guide weighs in at just 23 grams, is easy to assemble thanks to a smart I BB CENTER TO TOP OF SEATTUBE 390.0 mm 15.4 in 440.0 mm 17.3 in 480.0 mm 18.9 in 530.0 mm 20.9 in
mounting system and can accommodate 30T to 36T chainrings. J SEAT ANGLE 73.6 ° 73.6 ° 73.6 ° 73.6 °
K CHAINSTAY 425.0 mm 16.7 in 425.0 mm 16.7 in 425.0 mm 16.7 in 425.0 mm 16.7 in
The new Scale dropouts are designed to be integrated on the thru-axle system thanks to a
L REACH 398.7 mm 15.7 in 422.3 mm 16.6 in 443.2 mm 17.4 in 465.5 mm 18.3 in
hollow tube design that allows a simple and lightweight structure.
M STACK 599.0 mm 23.6 in 603.6 mm 23.8 in 617.7 mm 24.3 in 627.1 mm 24.7 in
N STEM LENGTH 60.0 mm 2.4 in 70.0 mm 2.8 in 80.0 mm 3.1 in 90.0 mm 3.5 in
0 TRAIL 83.9 mm 3.3 in 83.9 mm 3.3 in 83.9 mm 3.3 in 83.9 mm 3.3 in

| 04 ENGLISH SCALE | BIKE USER MANUAL BIKE USER MANUAL | SCALE ENGLISH 05 |
 •• IMPORTANT! ••BASIC SET-UP OF FORKS
SCOTT Scale 3 is designed around the BOOST platform so many of the fitted parts: cranks/
Recommended tools for the shock setup:
wheels/dropouts/forks differ from traditional cycle parts. Always consult your authorized
SCOTT dealer for advice on replacing or repairing any part of your SCOTT bike! -- The SAG tool that came with your bike. *Fox forks only
-- A shock pump with a special air valve connector (not supplied with this bike), this will
help stop air from escaping while removing the pump from the shock valve.
••RIDELOC
This section refers to SCOTT bikes fitted with the RIDELOC system. For all non-RIDELOC
systems please refer to the specific fork manual for your setup.
The RIDELOC system offers the rider full control of all 3 modes of the front forks with a
single lever, the position and function of the RIDELOC lever make for effortless control over
the forks function.
The 3 basic functions of RIDELOC system are:
-- Climb-out Mode
-- Traction Mode
-- Descent Mode

There are 3 positions of the RIDELOC remote lever.

1. CLIMB MODE: The fork is nearly locked; climbing on asphalt roads is now possible with Please note that air will flow into the hose and indicator when counterchecking the air
little power loss. A simultaneous blow-off-system prevents the forks being damaged in pressure, this will give the appearance that the shock has less air pressure than it was setup,
case the rider does not open the system while crossing obstacles. your shock may need to be adjusted once this action is made.

2. TRACTION MODE: Altering the dampening of the forks will result in climbing with reduced Please also note that the indicators of shock pumps have a tolerance of max. 10%.
“bobbing” and still offers optimum control of the front wheel.
3. DESCENT MODE: Full travel of the fork. For bikes spec’d with Fox forks:
You can find more specific information about Fox set
You can only assemble the “standard” RIDELOC remote lever in “left side upward position” up on Fox’s website, please use your fork ID number
on the handlebar (this is usually fitted on bikes with x2 front chainrings). to find more useful setup tips for your exact fork
(visit: ridefox.com)
On bikes with X1 chainring on the front the under bar RIDELOC remote lever in “left side
downward” position can be fitted as standard.
It is possible to change the RIDELOC lever to the underbar option if the bikes gears have
been changed to X1 system, a new alternative lever will be required for this adjustment;
please consult your local SCOTT dealer for more information on obtaining the correct lever
for your bike.

You will find the following positions on the remote lever:

| 06 ENGLISH SCALE | BIKE USER MANUAL BIKE USER MANUAL | SCALE ENGLISH 07 |
••SAG ••REBOUND FORK SET-UP
Your SCOTT bike will be supplied with a SAG tool to help set up your bikes suspension, these “Rebound” describes the speed the fork returns back
SAG tools can be easily clipped on the fork body and Fork dust seal. to its original length after absorbing an obstacle,
setting of this is very important for the handling and
correct function of the bike.
For the best performance it is recommended you start with SAG of 15-20% for forks.
The rebound adjustment dial location may vary form
1. Make sure before any adjustment is made that your forks are in the “open” position. fork to fork please consult the manual that came with
this bike.
2. With the fork pump attached to the fork valve, pump your desired pressure into the fork.
Once the pressure is achieved slowly compress and decompress your fork through 25% of
its travel 10 times. This will equalize the positive and negative air chambers and will change
After the fork pressure/SAG is correctly set ride your
the pressure on the pump gauge, if needed add or reduce pressure and repeat.
bike in a safe area with your riding gear/backpack,
Note the compression/decompression of the fork through the travel must also be done * Fox rebound adjuster shown
etc. While remaining in the saddle, ride you bike off a
if the pressure is reduced!
drop/kerb of about 10-15 cm.
3. Once your desired pressure is reached slide the rubber O-ring on the fork leg against the
-- If it bounces 1-2 times and settles the set-up is good.
dust seal, clip on your SAG tool if required.
-- If it bounces more than 3 times the rebound is too fast, turn the knob 1-2 “clicks”
4. Sit on your bike in your usual riding position (in your riding gear: if you carry a bag/ clockwise and repeat.
Hydration-system put it on,) don’t “bounce” the suspension while doing this, use a wall or
a friend for support if needed. -- If there is no bounce the rebound is too slow, turn the knob 1-2 click counter clockwise
and repeat.
5. Get off the bike gently without bouncing and check the O-ring position on the fork
-- Repeat these steps until the desired result is achieved.
stanchion, with the SAG adjuster clipped on. This makes it easy to see where your SAG is
set. Example below. Your SCOTT Scale bike was designed to be used in conjunction with a specific forks,
changing the forks on your bike may cause poor/unsafe riding characteristics or damage
to frame and components, please consult your SCOTT dealer for any assistance you need,
failure to do this may affect your warranty
This is the basic principle on setting your forks up, please always consult the fork owner's
manual for full instructions to familiarize yourself with the product.

•• IMPORTANT!
Do not sit on your bike with the shock pump
attached to the bike! ••REPLACEABLE REAR DROPOUT
On SCOTT Scale models for 2018 the rear derailleur hanger is replaceable, this hanger is
available in two options depending on if your bike is equipped with a standard or direct
mount rear derailleur.

FOR CARBON SCOTT SCALE 3 FRAMES ONLY:

Sram and non-direct Shimano direct

mount derailleurs mount derailleurs
SCOTT part number 254090 SCOTT part number 254091

| 08 ENGLISH SCALE | BIKE USER MANUAL BIKE USER MANUAL | SCALE ENGLISH 09 |
If your dropout needs to be replaced, we recommend this work should be carried out by
your local SCOTT dealer as the rear derailleur may need adjustment, failure to adjust this
••BRAKE MOUNT
correctly may result in accident or damage to your bike.

•• IMPORTANT!

•• IMPORTANT!
We recommend all work should be carried out by your authorised SCOTT dealer!
We recommend all work should be carried out by your authorised SCOTT dealer!
There is an option to use either a 160 or
If you wish to change this item yourself, please ensure the bike is supported correctly to 180mm brake rotor on the rear of for SCOTT
prevent damage. Please refer to the general manual supplied with your bike for instructions. Scale carbon with the use of the correct
adaptor (note this does not apply bikes with
boost Q/R).
New mounts are available from your authorized
SCOTT dealer and the size is marked on the
underside of the mount.
Part number: 254096 /160 mm brake mount.
Part number; 254095 /180 mm Brake mount.

If you wish to change this item yourself, please ensure the bike is supported correctly to
prevent damage. Please refer to the general manual supplied with your bike for instructions.

Before installing the new hanger first Insert the end cap through the frame and
make sure the area is clean; insert into the hanger.
the hanger. For this adaptor to be fitted you must remove the rear wheel and rear brake calliper.
Once all the correct items are removed the new mount will fit by swinging into place.

Make sure the location arrow is pointing Insert the second bolt in the rear of the
to the lower bolt hole; insert the bolt (Max dropout (Max torque 1.5 N/M)
torque 1.5 N/M)

Once the bike is reassembled please insure the wheels are refitted correctly and the gears
are set correctly including the over shift stops, please consult your authorized SCOTT dealer
for assistance.

| 10 ENGLISH SCALE | BIKE USER MANUAL BIKE USER MANUAL | SCALE ENGLISH 11 |
 •• IMPORTANT!
For 180mm rotors, please ensure the conical washer on the front mount is fitted!
The inserts are marked A-E, these letters dictate what cables can be used; these are the
same for left and right.

Refit the wheel and brake calliper checking the correct operation of all the components
before riding, if in any doubt please contact your SCOTT dealer for assistance and advice.

HT: HT-Blank:
this is the cover plate this is the no cable option
for all cable options

A: B: C:
1x Mechanical cable 2x Mechanical cables 2x mechanical cables
1x hydraulic

••CABLE GUIDES AND CABLING

On the SCOTT Scale carbon the cable guides on the headtube can be changed if required
so different cable configurations can be used.
The main cover plate of the cable guide is available in two options:
-- HT-Blank: this can be used when no cables are to be routed.
-- HT: this is open and can be used for different cable options.
D: E:
If cables are to be routed you must select the correct insert for the cover depending on the
1x single cable & Di2 Single cable and Live valve
configuration you require, the inserts can be easily changed in cover plate once the cables
have been removed and the cover removed from the bike.

If you wish to change or replace the headtube cableguide set on your SCOTT Scale this kit
can be ordered from your local SCOTT dealer.
SCOTT part number: 266587 and consists of:
2x HT/A/B/C/D
1x HT-Blank/E

| 12 ENGLISH SCALE | BIKE USER MANUAL BIKE USER MANUAL | SCALE ENGLISH 13 |
These cable guides are fitted with a single bolt, the fixing torque of this must not exceed
0.75-1 N/M.
••ADJUSTMENT
We recommend all adjustments are carried out by your local authorized SCOTT dealer but
basic maintenance and checks should be done regularly before each ride as described in the
With the many different cabling options it is possible to customise the cable routing slightly general manual that was supplied with your bike.
depending what components you wish to run, it is recommended that handlebar cables
that come from the right hand side enter the frame on the left, and handlebar cables that Please pay attention to all instructions and torque settings, if you have any doubts please
come from the left hand side enter the frame on the right, while this is not crucial to the contact your dealer,
performance of the bike it may help to prevent any cable rub. *in addition to the torque settings please note all bikes with a dropper type seatpost have a
Below is an example of a bike set up “European style” with a 1X set up and a dropper seatpost. seatpost clamp maximum torque of 5 N/M.

Please note that below is an example and that your bikes brakes need to be set up as per
the law in your country, please check with your local SCOTT dealer for this information.

••BB STANDARDS/FD MOUNTING DETAILS

The SCOTT Scale has a Press fit PF92 bottom bracket with an inner diameter of 41mm, this
is a press fit system and special tools are required for removal and refitting, please contact
your SCOTT dealer for assistance.

The SCOTT Scale (non RC models) uses

a high direct mount side swing front
derailleur only, this must be used with the
use of an FD adaptor plate.

It is not possible to mount a front

derailleur to RC frames/bikes.

| 14 ENGLISH SCALE | BIKE USER MANUAL BIKE USER MANUAL | SCALE ENGLISH 15 |
GUARANTEE ON SCOTT BIKES improper or incorrectly performed maintenance or repairs performed by someone other
than an authorized SCOTT dealer, use of parts or devices not consistent with the Product,
and alteration of the Product.

•• WARNING!
SCOTT Sports SA is not responsible or liable for any injury caused by any missing
All Products come with a manual; please carefully follow the instructions located there
or affixed elsewhere to the Product. To the extent permitted by law, consequential and
incidental damages are not recoverable under this limited warranty.
compliance with these instructions, particularly but not limited to misuse, incorrect
maintenance, incorrect set-up and handling, neglect or abuse. Failure to follow these
instructions can result in component failure, serious personal injury. Component failure How do you make a claim under this limited warranty?
can lead to loss of control of the bicycle and result in serious personal injury. To make a claim under this limited warranty, you must notify SCOTT of the claimed defect
within the warranty period and timely return the Product to SCOTT at your expense for
inspection. Please contact your authorized SCOTT dealer, call SCOTT’s customer service
What is Covered? or the national SCOTT distributor (dealer locator: www.scott-sports.com). All returned
This warranty covers defects in materials and workmanship at the time of transfer of risks in Products must be accompanied by proof of purchase (receipt) from an authorized SCOTT
frames, swingarms and forks (provided it is a fork of SCOTT) on SCOTT branded bikes sold dealer or this limited warranty will not apply. In case of replacement or refund, returned
completely assembled by SCOTT or an authorized SCOTT dealer (“Product”). Product becomes the property of SCOTT.
A protocol for the handing over of the Product (which you will find at the end of the manual)
How long does coverage last?
will remain in copy at the SCOTT dealer after acceptance and signature of the consumer. It
This voluntary manufacturer’s warranty is limited to five years for frames and swingarms,
is obligatory to show this protocol of handing over together with the defective part in case
respectively two years for forks, from the date of purchase of the Product and is limited
of a warranty claim given that it provides evidence of purchase or this limited warranty will
to the first purchaser of the Product and subject to the prior registration of your SCOTT
not apply.
bike on www.scott-sports.com within 10 days as of the date of purchase. Transfer of
the Product from the first purchaser to another person terminates this limited warranty.
How do state laws affect your rights under this limited warranty?
The limited warranty of five years for the frames and swingarms shall only be granted
This limited warranty gives you specific legal rights, and you may also have other rights,
in case once a year a maintenance service has been effected according to maintenance
which vary from state to state.
requirements as set forth in the manual. The effected annual maintenance service shall
be confirmed by stamp and signature. In case such an annual maintenance service has
not been effected the warranty of five years for the frame shall be reduced to three years. Recommendation
Costs for maintenance and service have to be borne by the owner of the Product. We strongly recommend that you use only authorized SCOTT dealers for yearly maintenance
services and for repairs, as improper or incorrectly performed maintenance or repairs voids
On Gambler, Voltage FR and Volt-X the warranty period is limited to two years. this limited warranty. Costs for maintenance service have to be borne by the consumer.
Repaired or replaced Products are covered for the remainder of the original warranty
period and subject to the conditions outlined in the original warranty, to the extent
permitted by law.
Hereby SCOTT grants a worldwide voluntarily manufacturer’s warranty. To the extent
permitted by law and unless a shorter duration is stipulated by law, any warranties implied
by law are limited in duration to maximum five, respectively two years, from the date of
purchase of the Product and are limited to the first purchaser of the Product.

What will SCOTT do in the event of a guarantee case?

SCOTT will replace the defective product with a product of a quality or nature and similar
level, will repair or refund the purchase price (after presentation of the proof of purchase of the
product), at its sole discretion. Non-defective components are replaced at your expense. In
such a case, we will contact you before replacing the non-defective part for your agreement.
5
What does this limited warranty not cover? SCOTT Bikes
This limited warranty does not cover defects which did not exist before the transfer of
Gambler, Voltage FR, Volt-X
risks. This limited warranty does not cover Products used in rental operations. This limited
warranty does not cover purchases of not completely assembled bikes. This limited warranty
does not cover any defect caused by “wear and tear” (a complete list of all parts of “wear
and tear” can be found in the general manual that came with your bike), accident, neglect,
improper handling, colour fade due to exposure to sunlight, abuse, misuse, an act of God,
improper assembly, non-compliance with recommended maintenance and care procedures,

| 16 ENGLISH SCALE | BIKE USER MANUAL BIKE USER MANUAL | SCALE ENGLISH 17 |