RecoverPoint Deploy Questions

1. When determining the Journal volume size, which factors must be considered?
A. Rate of change, percentage of sequential writes, and the RPO/RTO
B. Number of snapshots to retain, rate of change, and the number of RPAs
C. Synchronous or asynchronous replication, RPO/RTO, and the network type
D. Rate of change, application data type to be replicated, and the number of snapshots to
retain

2. Which factors should be considered when using Deployment Manager to connect a

RecoverPoint cluster to an existing cluster?
A Connectivity Protocol and Number of RPAs
B. License Type and RPA Type
C. Connectivity Protocol and RPA Type
D. License Type and Connectivity Protocol

3. You are performing a RecoverPoint cluster installation using Deployment Manager. The new
cluster is using physical RPAs. During the "Connectivity Settings" step of Deployment
Manager, which interface(s) can be configured to use DHCP?
A LAN only
B. Cluster management
C. WAN and LAN
D. iSCSI-1 and iSCSI-2

4. What is the maximum number of copies that RecoverPoint can maintain?

A. RecoverPoint with VNX(SE): 1 production copy + up to 2 replicated copies
B. RecoverPoint EX/CL: 1 production copy + up to 6 replicated copies
C. RecoverPoint with VNX(SE): production copy + up to 4 replicated copies
D. RecoverPoint EX/CL: 1 production copy + up to 2 replicated copies

5. What is the maximum number of concurrent initial syncs that can be performed in a Unity
VSA setup with RecoverPoint?
A. 4
B. 16
C. 8
D. 32

6. Which user account will launch the Installation Manager to allow the RecoverPoint
administrator to make RPA parameter changes and test or diagnose connectivity issues?
A. webdownload
B. boxmgmt
C. admin
D. security-admin
RecoverPoint Deploy Questions

7. A company is deploying a physical RPA cluster to protect a Unity array. Which requirement
must be verified prior to running the Deployment Manager, RecoverPoint with Unity Installer
wizard?
A. Unity RecoverPoint write splitter is enabled
B. CHAP secrets are configured for the Unity iSCSI ports
C. RecoverPoint with VNX(SE) license is installed on the Unity system
D. RPA FC ports are not zoned to the Unity synchronous replication ports

8. A service provider is implementing a VMAX splitter with four RPA RecoverPoint/EX clusters.
How should the RPA and the host FC ports be zoned, and the LUNs masked?
A. Only RPA 1 and RPA 2 must be zoned and masked to the same FA ports as the hosts
B. All RPAs must be zoned and masked to different FA ports as the hosts
C. Only RPA 3 and RPA 4 must be zoned and masked to the same FA ports as the hosts
D. All RPA FC ports must be zoned and masked to the same FA ports as the hosts

9. Which RPA type(s) supports replication of XtremiO volumes?

A. Gen 6 only
B. Gen 5 and vRPAs
C. Gen 5 and Gen 6
D. Gen 6 and VRPAs

10. An application is running on XtremlO replicating to another XtremlO using RecoverPoint with
the following:
What is the minimum required size for the Journal volume using the default parameters?
A 72.4 GB
B. 57.3 GB
C. 10 GB
D. 60 GB

11. A RecoverPoint administrator is implementing a RecoverPoint/EX cluster using a VNX splitter.

The zoning between the RPAs and the VNX ports is completed and the RPA ports are
available in the connectivity status on the VNX.
What is the next step to complete?
A. Add the RPAs to the storage groups
B. Create a storage group on the VNX for RecoverPoint
C. Create a LUN on the VNX for RecoverPoint
D. Each RPA port should be manually registered with the VNX

12. An administrator ran the capture load command on a RecoverPoint cluster during a high-load
issue. However, the administrator forgot to capture the output. Where can the RecoverPoint
Cluster Load report be located?
A. In the output from running the Collection System Information wizard
B. https://Cluster_Management_IP/info/long_term_statistics
C. https://Cluster_Management_IP/info/load_balancing/
D. In the output from the events log
RecoverPoint Deploy Questions

13. A system administrator wants to configure a RecoverPoint cluster and the required
Repository volume created on a VNX accessible by all RAs. However, the Repository volume
is not visible in Deployment Manager to continue the RecoverPoint cluster configuration.
What is a possible reason for this situation?
A. Volume is configured as with FAST disabled
B. Volume is configured as a Thick LUN
C. Volume is configured as a Thin LUN
D. Volume is configured as a private LUN

14. Which environment settings can be changed in the System Modification wizard for an RPA
connected to a VNX, VMAX, or a VPLEX?
A VNX cluster name, Time zone, and DNS server
B. VMAX credentials, Time zone, and DNS server
C. VPLEX cluster name, Time zone, and DNS server
D. RecoverPoint cluster name, Time zone, and DNS server

15. What is required to add a local copy to a Consistency Group that already contains one
remote copy?
A. RecoverPoint system must be RecoverPoint with VNX(SE)
B. RecoverPoint license type must be RecoverPoint/CL
C. Write splitter type at the production cluster must be the same type as the remote copy
D. Sufficient local copy licensed capacity on the production cluster

16. A storage administrator wants the ability to have the same point-in-time image across
multiple Consistency Groups. If a RecoverPoint system uses vRPAs to protect data stored on
VNX arrays, which feature provides this functionality?
A. Group Sets
B. Snapshot Consolidation
C. Consistency Groups
D.Bookmarks

17. What is a supported method to re-image a Gen 6 RPA node?

A. Boot from the RPA DVDROM
B. Boot from the USB memory stick
C. Boot from the LAN
D. Boot from the RPA hard drive

18. Where and for which purpose should the rp_ import-certificate command be issued?
A. Deployment Manager - to set up credentials
B. VPLEX CLI - to obtain management, installation, and integration information about volume
types
C. RecoverPoint and VPLEX - to obtain management, installation, and integration information
about volume types
D. RecoverPoint CLI - to obtain management, installation, and integration information about
volume types
RecoverPoint Deploy Questions

19. You are deploying a new RecoverPoint cluster using a VPLEX array; however, you need to
determine where to locate the Repository volume. What is the recommended location for
the Repository volume?
A. On the VPLEX as a distributed volume
B. On the VPLEX as a metadata volume
C. On third-party storage
D. On the VPLEX as a virtual volume

20. You are deploying RecoverPoint and need to configure zoning for a Brocade switch. How can
the RPA WWNs / PWWNs be retrieved?
A. Log into RecoverPoint Management IP with admin user and run get_ initiators
B. Log into RecoverPoint Management IP with admin user and run get system_ settings
C. Log into each RPA with boxmgmt user and gather the information from the SAN
Diagnostics menu
D. Start Deployment Manager and allow Deployment Manager to automatically configure
the zones

21. A storage administrator has seen high-load events in their RecoverPoint environment. The
administrator wants to review the performance data for the past week with RecoverPoint. In
addition, the administrator wants the raw data saved to a spreadsheet to review and create
graphs of system performance over a period of time.
Which CLI command should be used?
A. bahance_load
B. detect _bottlenecks
C. export_ statistics
D. get rpa statistics

22. You need to install a new Gen 6 RPA within a VNX storage environment. However, while
verifying the inventory, you discover that the local HDD on one of the RPA nodes was
misplaced.

What are the correct slots for the RAID 1-protected drives?

A. Slot 0 and 3

B. Slot 0 and 1

C. Slot 0 and 2

D. Slot 1 and 2

23. You complete the installation of a RecoverPoint with VNX(SE) system with two clusters. The
company's storage administrator wants to know how to add an additional cluster at their
new data center.

Which information should be provided to the administrator?

A. Install the new RecoverPoint/EX cluster

Connect thim new cluster to the existing system

B.Install the new RecoverPoint/EX cluster

RecoverPoint Deploy Questions

Add the license to the new cluster

Connect the new cluster to the existing system

C. Convert the new RecoverPoint/EX cluster

Add the license to the new cluster

Connect the new cluster to the existing system

D. Convert the existing system to RecoverPoint/EX

Install the new RecoverPoint/EX cluster

Connect the new cluster to the existing system

24. A RecoverPoint storage administrator needs to protect a mission-critical application. The

application is stored on three volumes provisioned from a new VNX. Once the Consistency
Group is created for the application, how many replication sets will the group contain?

OA Determined by the number of copies

B. 1

C. 2

D. 3

25. A company's host systems are configured with iSCSI HBAs and they want to directly attach
the RPAs to a VNX. Which configuration will meet this requirement?

A. RPAs physically connected to each other through both their iSCSI ports

B. RPAs physically connected to each other through their WAN ports

C. RPAs physically connected to each other through their FC ports

D. RPAs cannot be physically connected to each other

26. Prior to installation, you are meeting with the network administrator as part of your site
preparations. The administrator wants to know the minimum number of IP addresses
required for their two-node VRPA cluster.

27. What is the minimum number of IP addresses needed?

A3

B. 6

C.5

D. 9
RecoverPoint Deploy Questions

28. The production and remote copies of a Consistency Group are hosted on XtremO arrays.
During application testing of the remote copy, the Image Access log capacity does not
advance.

Why is the Image Access log capacity static?

A. Application writes are to an XtremlO snapshot and are not stored in the Journal

B. Journals on XtremO arrays are virtual and do not track the writes

C. Application writes are stored in RPA memory when using the XtremO array

D. Failover has not completed so the writes have not been distributed to the Journal

29. In order to perform dynamic resizing of a replication set, what is a requirement?

A. Both production and the copies must be provisioned from an XtremO array

B. Both production and the copies must be provisioned from a VPLEX array

C. Copy must be provisioned from an XtremlO array; the production can be on any supported array

D. Production must be provisioned from an XtremO array; the copy can be on any supported array

30. Franklin Cluster: IP and connectivity settings

Define the new RPA IP settings at duster Frankin

K 1. Prerequistes

# 2. Configuration Fle

7 3. Login credentials

# 4. Add new RPAS

→ 5. IP and connectivity settings

6. Apply configuration results

7. Storage Configuration

2 7. 1. zonng

$ 7.2. SAN diagnostics

→ 7. 3. Configure new RPAS

8. Apply changes

9. Summary

RPA IP addresses and connectivity settings

Cluster managemenk

10.127.118.65
RecoverPoint Deploy Questions

WAN IPV4

LAN IPV4

255.255.255.224

Interface netmask

255.255.255.128

WAN IPV4

LAN IPV4

RPA 1

RPA 2

RPA 3

10.127.118.63

10.127.118.68

10.127.118.69

172.168.1.20

172.168.1.21

172.168.1.23|

31. Based on the exhibit, what describes the state in which RPA-3 must be in prior to selecting
"Next" to advance the wizard?

A. Attached to the displayed RecoverPoint cluster

B. Powered on and configured with the displayed LAN address

C. Connected to the SAN with storage provisioned

D. Powered on and configured with the displayed WAN address

32. Which RPA cluster iSCSI configuration setting(s) can be changed in the System Modification
wizard on the RPA ¡SCSI Configuration display?

A. IP only

B. CHAP and MTU

C. IP and MTU

D. CHAP and IP
RecoverPoint Deploy Questions

33. A VPLEX distributed device has been configured as a production copy in a MetroPoint
Consistency Group. However, a fracture has occurred between the two VPLEX clusters.

What is the expected behavior of the RecoverPoint replication?

A Replication will pause until the distributed device fracture is resolved

B. Replication continues to both clusters as the distributed device fracture does not impact
replication

C. Replication will continue through the VPLEX winner site

D. Replication to the losing site will mark all writes and distribute them when the distributed device
fracture is restored

34. What is the state of a RecoverPoint cluster during the running of the Deployment Manager
Cluster Conversion wizard?

A Monitoring Mode

B. Read-only Mode

C. Diagnostic Mode

D. Maintenance Mode

35. What is a characteristic of a cluster that is running on RecoverPoint 5.0 or later?

A. If the WAN and LAN are on different network adapters, they must be on different subnets

B. If the WAN and LAN are on different network adapters, they must be on the same subnets

C. If the WAN and LAN are on different network adapters, different subnets are optional

D. WAN and LAN traffic cannot be on the same network adapters

36. How does Unisphere identify a RecoverPoint initiator with VNX through RPA registration?

A. RP._< name >_0_0

B. RPA_0_0

C. RPA_< wWn >

D. RP_HBA_0_0

37. Which type of RecoverPoint Consistency Group contains both active and standby production
copies?
RecoverPoint Deploy Questions

A. MetroPoint Consistency Group

B. XtremlO Consistency Groups

C. Distributed Consistency Groups

D. Any group with multiple remote copies

38. A RecoverPoint administrator wants to add volumes from an unlicensed array to a

RecoverPoint/EX cluster. Which supported RecoverPoint volume type(s) addresses the
administrator's requirement?

A. Journal and Copy

B. Repository and Journal

C. Journal only

D. Repository only

39. Which ports are required for proper communication between Deployment Manager and the
RecoverPoint Appliances?

A TCP 21, 22, 7225, and 8082

B. TCP 21, 22, 80, 443, and UDP 53

C. TCP 21, 22, 25, 80, and 7225

D. TCP 21, 22, 25, 80, and 443

40. You completed creating the RecoverPoint zoning on the SAN switch based on the design
document. What is the zoning method that should be used while running the RecoverPoint
with VNX(SE)

Installation wizard?

A. Semi-automatic

B. Dual initiator zoning

C. Manual

D. Automatic
RecoverPoint Deploy Questions

41. Which command should be used to verify if the VMAX LUNs to be used with RecoverPoint
are tagged?

A symdev -sid list -dev_tag

B. symdev -sid list - tagged

C. symdev -sid list - rp_tag

D. symdev -sid list -reypnt _tag

42. A company is implementing a total of four VNXs; two at their production site and two at their
disaster recovery site. In addition, the company wants to manage all clusters as one
RecoverPoint system.

When installing the RecoverPoint cluster, what should be selected in the RecoverPoint
Deployment Manager wizard?

A. RecoverPoint Installer

B. RecoverPoint with VNXe Installer

C. RecoverPoint Installer followed by Converter to convert to RecoverPoint/EX

D. RecoverPoint with VNX Installer

43. You are installing a new Gen 6 RecoverPoint Appliance (RPA). After completing the physical
installation, you log into the RPA for the first time using the "boxmgmt" account.

How can the RecoverPoint version running on the RPA be determined?

A. Running the get_ version command

B. Obtained using the Diagnostics menu

C. Displayed in the opening view after login

D. Obtained using the Installation menu

44. What is the maximum number of arrays, per cluster, supported with a RecoverPoint/EX
license?

A. 2

B. Unlimited

C. 1

D.3
RecoverPoint Deploy Questions

45. An boyad batin orgasting storage protection solutions for multie companies. ner solor

An organization is hosting storage protection solutions for multiple companies. Their solutions are
based on a single VNX array. What is the maximum number of RecoverPoint clusters that can be

A. Five clusters, assuming only vRPAs are used

B. Eight clusters, assuming each LUN is attached to only one cluster at a time

C. Six clusters, assuming each LUN is attached to only one cluster at a time

D. Eight clusters, assuming each LUN is replicated across the clusters

46. When the admin user password has been lost, how can the password be reset?

A. Log into the LI using boxmgmt and then run the set _user name-admin password= command

B. Log into the bomgmt menu, select Diagnostics => Advanced Diagnostics => Run Internal
Commands => and then run the passwd admin command

C. Log into the CLI with the security role and then run the set.

user

name=admin password= command

D. Reboot the appliance from DVD and then select "password recovery" from the GRUB menu

47. A company decided to change their VNX environment from Mirror View to RecoverPoint with
VN(SE) as a disaster recovery solution. They initially planned to purchase four RPAs at each
site to replication between Sites A and B. However, to ensure the company uses their large
server inventory, management plans to change from physical RPAs to vRPAs.

What effect do their plans have on the license procurement?

A. An additional RecoverPoint with VNX(SE) license is needed

B. A RecoverPoint/EX license is needed

C. An advanced RecoverPoint license is needed

D. Licensing remains same; no action required

48. What is the correct sequence of steps for Snap-based replication on XtremlO?

Answer Area

Steps

1. Create the snapshot

RecoverPoint Deploy Questions

2. Create a second snap, and then retrieve the DIFF between the first and second snapshot
3. Transfer the DIFF
4. Create and promote the snapshot
5. Get the DIFF between the snapshot and the root volume

Transfer the DIFF

Create the snapshot

Create and promote the snapshot

Get the DIFF between the snapshot and the root volume

Create a second snap, and then retrieve the DIFF between the first and second

snapshot

49. A Consistency Group contains a production and a remote copy. Both are provisioned from
XtremO arrays. Where are the snapshots that represent the point-in-time images kept during
normal replication?

A. On the XtremO array containing the production volume

B. In the Journal pool on the XtremlO array containing the copy volume

C. On the XtremO array containing the copy volume

D. In the Journal pool on the XtremlO array containing the production volume

50. When are new RecoverPoint licenses added to a new cluster?

A. Before the Deployment Manager Installer has started

B. During the Deployment Manager Installer "Apply Configuration" step

C. After the Deployment Manager "Connection" steps are completed

D. During the Deployment Manager "Prepare New Cluster for Connection" step

51. A storage administrator wants to implement a new RecoverPoint with VNX(SE) cluster using
virtual RPAs in their VMware environment. The administrator wants to ensure the highest
availability for all communication within the cluster.

What is the recommended number of virtual switches required for this type of
configuration?

A. 2

B. 4

C.1

D. 3
RecoverPoint Deploy Questions

52. A company has a RecoverPoint with VN(SE) cluster with local replication connected to a VNX
array. They want to replace the VNX array with a Unity 600F array. All LUNs from the previous
storage will be deleted and new ones will be created in the new storage.

What changes need to be performed in the RecoverPoint cluster?

A. Replace old the Local Replication license for a new one using the Unity Serial number

B. Add a new Local Replication license using the Unity Serial number

C. RecoverPoint automatically recognizes the Unity array; no new licenses are required

D. Convert RecoverPoint with VN(SE) to RecoverPoint/EX and add a new Local Replication license
using the Unity Serial number

53. When manually registering each RPA initiator with the VNX, what is the required
configuration?

A. Initiator Type - RecoverPoint Appliance

Failover Mode - 3 (Passive Ready)

B. Initiator Type - RecoverPoint Appliance

Failover Mode - 0 (LUN Based)

C. Initiator Type - RecoverPoint Appliance

Failover Mode - 4 (ALUA)

D. Initiator Type - SGI

Failover Mode - 4 (ALUA)

54. What is the correct sequence of steps to implement RecoverPoint with XtremO?

Answer area

Steps

Add XtremlO to RecoverPoint

Map the replication LUNs

Create an initiator group on the XtremlO for the RecoverPoint cluster

Zone all RPA ports to XtremO Storage Controller ports

1. Add XtremIO to RecoverPoint

2. Zone all RPA ports to XtremIO Storage Controller ports
3. Map the replication LUNs
4. Create an initiator group on the XtremIO for the RecoverPoint cluster
RecoverPoint Deploy Questions

55. What is the correct sequence of steps to implement RecoverPoint with VPLEX?

Answer Area

Steps

Zone the RA FC ports to the VPLEX cluster VPLEX BE and FE ports

Register the VPLEX credentials in RecoverPoint

Register the RPA initiators with VPLEX and then create a storage view (masking)

Import the certificates and add the RecoverPoint cluster to VPLEX

1. Zone the RPA FC ports to the VPLEX cluster VPLEX BE and FE ports
2. Register the RPA initiators with VPLEX and then create a storage view (masking)
3. Register the VPLEX credentials in RecoverPoint
4. Import the certificates and add the RecoverPoint cluster to VPLEX
5. License VPLEX with RecoverPoint

License VPLEX with RecoverPoint

56. During the write phase of RecoverPoint replication, when does the RPA send an
acknowledgement back to the write splitter?

A. After the RPA has received an acknowledgement from all copies involved with replication

B. After the distribution phase has completed

C. After the local RPA has received an acknowledgement from the remote RPA

D. As soon as the RPA receives the write

57. While running the Deployment Manager Installer for a new cluster with two RAs, you
discover that one RPA is running a different version. Which action is required to resolve this
issue?

A. Continue the cluster installation and once finished, perform a RecoverPoint code upgrade

B. Ensure that all RPAs are running on the same version and then retry the failed step

C. Download a new version of Deployment Manager supporting a lower RecoverPoint version found
on the RPA

D. Continue running Deployment Manager and on the "Update RecoverPoint Release" step, select
the required code version

58. A RecoverPoint administrator performs a Consistency Group failover to a remote copy. What
happens to the point-in-time images stored in the copy Journal after the copy becomes
production?
RecoverPoint Deploy Questions

A. Images are consolidated

B. Images art deleted

C. Images are replicated to the new production Journal

D. Images are replicated to the new copy Journal