The integral microprocessor analysis the signal according to the factors such as signal strength and rate of increase, then confirms these pattern with the pre- programmed fire scenarios and smoke patterns for a faster and safer response. By intelligent analysis, the smoke detection sensitivity will be automatically adjusted according to temperature change, providing a rapid response.
Secure and speedy communication through
the on board processor enables the detector to make its own decision, resulting in greater automation. The sensor and the panels utilized fuzzy logic providing an almost limitless cause and effect scenarios.
Drift compensation, to monitor for the long
term changes caused by aging, humidity, temperature, dust, etc. constant Features and Benefits monitoring and self adjusting, the I-9101 updates sensitivity base line for its sensing 1. Built in 8 bit microprocessor element. Even when the detector raises a 2. Algorithm maps for faster response warning advising that it requires cleaning, and false alarm rejection the sensitivity remains the same as the day 3. Analogue sensing it was installed. 4. Secure and speedy communication 5. Intelligent Linear Drift compensation Electronic addressing can be done through 6. Self diagnosis and history log Handhold Programming device (P-9910), 7. Electronic addressing purchased separately. 8. Sensing chamber for exceptional dust Technical Specifications proof ability 9. Twin LED for 360º vision • Standard: EN54-part7 10. Built-in remote indicator output • Approval: LPCB,CE 11. Low profile design • Protection rating: IP 32 • Operating voltage: 24Vdc Loop Description voltage • Operating Current: The I-9102 Optical Smoke Detector is the • Standby current 0.6mA ideal device for most application due to its • Alarm Current 2mA excellent linear response to a wide variety of • Operating temperature: -10°C to different type of smoke patterns. The unit +50°C meets the sensitivity requirement of EN 54 • Relative humidity: 95% part 7, European Standard and approved by • Application: Indoor use Loss Prevention Certificate Board (LCPB). • Detecting range: 100 sqm elevated than 6m, 80 sqm less than 6m Aesthetically pleasing with a low profile • Field Programmable sensitivity: design, unobtrusive to complement modern 0.10dB/m to 0.56dB/m – 3 level building designs. The unit incorporates an • Visual Indicator: twin LED, Red ( lit intelligent processor that provides Algorithm steady when alarm, 3 sec interval map, Built-in A/D converter, Drift blinking at normal state) compensation, Self Diagnosis and history log. • Material and colour: ABS, off-white • Wiring: 1 pair non polarized • Dimensions: diameter 10cm; height 5cm Intelligent Optical Smoke Detector I-9102 CONCRETE PAD OR HOLDING PAD EMBEDDED BOX
Mounting Standard Base
The detector is mounted using our standard MARK−LINE 2ND MARK−LINE base DZ-03.Multiple-direction design allows easy direction adjustment. Suitable for surface mount only, mount on standard 1gang electrical back box with a mounting LED INDICATOR
hole of 65mm spacing ROTATE CLOCKWISE
CONCRETE PAD OR EMBEDDED BOX
HOLDING PAD SCREW Programming The address of the detector and sensitivity HOLE can be programmed using GST handhold STANDARD DETECTOR BASE programmer (P-9910), purchased separately. Connect the two wires of the BASE MOUNTING handheld programmer to terminals 1 and 3 of the detector. Wiring and Connection Connect the wires to the required terminal according to the wiring diagram below; terminal 1 and 3 for the loop; connection of remote indicator output is on terminals 2 and I−91XX 4. The cable must be fire rated type and the DETECTOR
size depends on the distance and application.
Minimum size gauge 1.0mm²(18 AWG)
DETECTOR TERMINAL
FIELD DEVICE PROGRAMMER
TERMINALS
TO NEXT DEVICE 1 PAIR FIRE CABLE Selection of compatible Control Panels 1 2 Compatible with all GST Intelligent Fire FROM CONTROL PANEL Alarm Panels GST 100, GST 200, GST 5000 and GST 9000. 1 PAIR FIRE CABLE
4 3 REMOTE INDICATOR
Ordering Information: Part No Description Weight Pack Detector Installation /Kg Qty per The Intelligent optical smoke detector should Box be installed in compliance with all local codes I-9102 Intelligent 0.123 120 having a jurisdiction in your area or NFPA 72 Optical Smoke National Fire Alarm Code, NFPA 70 National Detector with Electrical Code, BS 5389 and EN54. Before Remote installation verify the proper wiring and base Indicator are firmly mounted to prevent detector DZ-03 Standard 0.050 360 damage before the installation. Point the Detector Base detector in the base by the mark-line and secure the detector in that position by rotating it clockwise until it reaches the next MANUFACTURED IN ACCORDANCE WITH mark line.
Note: Specifications are subject to change without notice.
