Scribd
Upload
21 views9 pages

Design and Construction

Electrical and Electronic project material

Uploaded by

Michael Nwaokike
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
21 views9 pages

Design and Construction

Electrical and Electronic project material

Uploaded by

Michael Nwaokike
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 9

DESIGN AND CONSTRUCTION OF RUNNING 50 LEDs CHASER LIGHT

BY

ULONNAM PETER

ND2021/00724/1/CET

DEPARTMENT OF COMPUTER ENGINEERING

ABIA STATE POLYTECHNIC, ABA

FEBRUARY, 2024

i
DESIGN AND ONSTRUCTION OF A RUNNING 50 LEDs CHASER LIGHT

BY

ULONNAM PETER

ND2021/00724/1/CET

A PROJECT REPORT SUBMITTED TO THE DEPART METN OF COMPUTER ENGIEERING

SCHOOL OF ENGIEERING TECHNOLOGY, ABIA STATE POLYTECHNIC, ABA.

IN PARTIAL FULFILLMENT OF THE REQUIREMENT OF THE AWARD FOR NATIONAL

DIPLOMA IN COMPUTER ENGINEERING TECHNOLOGY

ii
APPROVAL PAGE

This is to certify that the project design and construction of Running 50 Leds Chaser

Light was carried out by Ulonnam Peter, ND2021/00724/1/CET, department of

Computer Engineering, Abia State Polytechnic, Aba. This project is submitted in

partial fulfillment of the requirement for the award of National Diploma under the

strict supervision of the undersigned;

………………………………….…………… Date…………………………

Engr Igwe A. F

(project supervisor)

….……………………………………….

Engr Innocent Alozie Date………………………

(H.O.D)

………………………………… Date…………………………

External Examiner

iii
DEDICATION

This project is dedicated to the almighty God for his protection, kindness over my life

throughout my study in this school and also my parents who has supported both

financially, spiritually and morally care towards me. May their effort never go in vain.

iv
ACKNOWLEDGEMENT

I wish to express my sincere thanks to Almighty God who has been the source of my

inspiration through my study at Abia state Polytechnic Aba.

My profound gratitude goes to my project supervisor in the person of Engr Igwe A.F.,

for his constructive criticism and politeness in going through this work, I’m really

grateful sir.

My gratitude goes to my entire lecturers, may God bless you all for your positive

contribution towards my life during my program.

Also, my parents for their support both morally and financially.

ABSTRACT

v
This project work is on an “LED CHASER LIGHTING SYSTEM” which is an electronic
display used in advertising and distribution of information in public and private
locations. The displays are seen mainly in many public places such as airports, train
stations, and shopping malls. In this work, signs uses technology such as LED to
display information and can be found in public spaces, transportation systems,
museums, stadiums, retail stores, hotels, restaurants, and corporate buildings. This
device was built with 555 timer ic and 4017 decade as the major components. The
device was built successfully and tested, it was seen that the device performed its
operation successfully.

vi
TABLE OF CONTENTS

TITLE PAGE i

APPROVAL PAGE ii

DEDICATION iii

ACKNOWLEDGEMENT iv

TABLE OF CONTENT v

ABSTRACT vii

CHAPTER ONE

INTRODUCTION

1.0 BACKGROUND OF THE STUDY 1

1.1 STATEMENT OF THE PROBLEM 1

1.2 OBJECTIVE OF THE STUDY 2

1.3 SCOPE OF THE STUDY 3

1.4 SIGNIFICANCE OF THE STUDY 3

1.5 LIMITATION OF THE STUDY 3

1.6 PROJECT ORGANISATION 3

CHAPTER TWO

LITERATURE REVIEW

2.0 HISTORICAL BACKGROUND OF LIGHT EMITTING DIODE 4

2.1 REVIEW OF COMMERCIAL DEVELOPMENT OF AN LED 6

2.2 REVIEW OF ELECTRONICS SIGN BOARD 7

vii
2.3 HISTORICAL BACKGROUND OF ELECTRONICS SIGN BOARD 8

CHAPTER THREE

METHODOLOGY

3.0 SYSTEM BLOCK DIAGRAM 12

3.1 SYSTEM CIRCUIT DIAGRAM 12

3.2 COMPONENTS LIST 13

3.3 CIRCUIT DESCRIPTION 13

3.4 CIRCUIT OPERATION 14

3.5 POWER SOURCE CONSIDERATIONS 18

3.6 DESCRIPTION OF MAJOR COMPONENTS USED 18

CHAPTER FOUR

TESTING AND RESULTS

4.0 CONSTRUCTION PROCEDURE AND TESTING 32

4.1 CASING AND PACKAGING 32

4.2 ASSEMBLING TESTING OF SYSTEM OPERATION

4.1 ASSEMBLING OF SECTIONS 33

4.2 TESTING OF SYSTEM OPERATION 33

CHAPTER FIVE

5.1 CONCLUSION

5.2 RECOMMENDATION

5.3 REFERENCES

viii
ix

You might also like