Scribd
Upload
266 views4 pages

T3 Tech Spec

The document provides wiring diagrams and instructions for connecting various subwoofer configurations to Ultimate Car Audio amplifiers. It recommends following the diagrams to prevent damage and maximize performance. The diagrams show mono, stereo, and bridged wiring options for single and dual voice coil subwoofers. Specifications for amplifier power output at different voltages and impedances are also included.

Uploaded by

Aguz Wibowo
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
266 views4 pages

T3 Tech Spec

The document provides wiring diagrams and instructions for connecting various subwoofer configurations to Ultimate Car Audio amplifiers. It recommends following the diagrams to prevent damage and maximize performance. The diagrams show mono, stereo, and bridged wiring options for single and dual voice coil subwoofers. Specifications for amplifier power output at different voltages and impedances are also included.

Uploaded by

Aguz Wibowo
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Ultimate Car Audio

Technical Pages
IMPORTANT!!!
In order to maximize the performance of our Class D amplifiers, it is highly recommended to follow the wiring diagrams below. Failure to do so may result in premature damage to your amplifier and/or subwoofers.
September 1, 2005 Ver. 1.0

T3-500D with one T3-10.3 / T3-12.3


Single voice coil subwoofer connection
MONO WIRING
+

Ultimate

888

888

Results in a 3 ohm load on the amplifier.

T3-500D with two T3-10.3 / T3-12.3


Single voice coil subwoofer connection
STEREO WIRING
+

Ultimate

888

888

Results in a 1.5 ohm load on the amplifier.

Performance Data
Operating Voltage - 13.8v
Amplifier Speaker Load RMS Power Current

Operating Voltage - 12.5v


Amplifier Speaker Load RMS Power Current

4 ohm 2 ohm

500W 1000W

45A 92A

4 ohm 2 ohm

500W 1000W

53A 100A

Note: No less than 4ga power and ground wire must be used in these wiring configurations. We also recommend the use of a 1 farad capacitor for optimized power delivery.
Ultimate Car Audio is not responsible for any damage that may occur to ones vehicle, as a result of improperly installed or configured amplifiers. Specifications subject to change. The data above is based on a controlled test bench environment. Test frequency is 100hz, at 1% THD.

Ultimate Car Audio


Technical Pages
IMPORTANT!!!
In order to maximize the performance of our Class D amplifiers, it is highly recommended to follow the wiring diagrams below. Failure to do so may result in premature damage to your amplifier and/or subwoofers.
September 1, 2005 Ver. 1.0

T3-500D with one T3-10.3DVC / T3-12.3DVC


Dual voice coil subwoofer connection
STEREO WIRING
+

Ultimate

888

888

Results in a 1.5 ohm load on the amplifier.

T3-500D with two T3-10.3DVC / T3-12.3DVC


Dual voice coil subwoofer connection
STEREO WIRING
+

Ultimate

888

888

Voice coils wired in series.

Voice coils wired in series.

Results in a 3 ohm load on the amplifier.

Performance Data
Operating Voltage - 13.8v
Amplifier Speaker Load RMS Power Current

Operating Voltage - 12.5v


Amplifier Speaker Load RMS Power Current

4 ohm 2 ohm

500W 1000W

45A 92A

4 ohm 2 ohm

500W 1000W

53A 100A

Note: No less than 4ga power and ground wire must be used in these wiring configurations. We also recommend the use of a 1 farad capacitor for optimized power delivery.
Ultimate Car Audio is not responsible for any damage that may occur to ones vehicle, as a result of improperly installed or configured amplifiers. Specifications subject to change. The data above is based on a controlled test bench environment. Test frequency is 100hz, at 1% THD.

Ultimate Car Audio


Technical Pages
IMPORTANT!!!
In order to maximize the performance of our Class D amplifiers, it is highly recommended to follow the wiring diagrams below. Failure to do so may result in premature damage to your amplifier and/or subwoofers.
September 1, 2005 Ver. 1.0

T3-1000D with two T3-10.3 / T3-12.3


Single voice coil subwoofer connection
STEREO WIRING
+

BRIDGE

Ultimate

888

888

Results in a 3 ohm load on the amplifier.

T3-1000D with two T3-10.3 / T3-12.3


Single voice coil subwoofer connection
BRIDGED WIRING
+

BRIDGE

Ultimate

888

888

Woofers are wired in parallel with each other.

Results in a 1.5 ohm load on the amplifier.

Performance Data
Operating Voltage - 13.8v
Amplifier Speaker Load RMS Power Current

Operating Voltage - 12.5v


Amplifier Speaker Load RMS Power Current

4 ohm stereo 4 ohm mono 2 ohm stereo 2 ohm mono

530W/ch 38A 1800W 59A 800W/ch 60A 2700W 105A

4 ohm stereo 4 ohm mono 2 ohm stereo 2 ohm mono

300W/ch 1000W 500W/ch 2000W

65A 105A 98A 210A

Note: No less than 0ga power and ground wire must be used in these wiring configurations. We also recommend the use of a 2 farad capacitor for optimized power delivery.
Ultimate Car Audio is not responsible for any damage that may occur to ones vehicle, as a result of improperly installed or configured amplifiers. Specifications subject to change. The data above is based on a controlled test bench environment. Test frequency is 100hz, at 1% THD.

Ultimate Car Audio


Technical Pages
IMPORTANT!!!
In order to maximize the performance of our Class D amplifiers, it is highly recommended to follow the wiring diagrams below. Failure to do so may result in premature damage to your amplifier and/or subwoofers.
September 1, 2005 Ver. 1.0

T3-1000D with one T3-10.3DVC / T3-12.3DVC


Dual voice coil subwoofer connection
STEREO WIRING
+

BRIDGE

Ultimate

888

888

Results in a 3 ohm load on the amplifier.

T3-1000D with two T3-10.3DVC / T3-12.3DVC


Dual voice coil subwoofer connection
BRIDGED WIRING
+

BRIDGE

Ultimate

888

888

Voice coils wired in series.

Voice coils wired in series.

Results in a 3 ohm load on the amplifier.

Performance Data
Operating Voltage - 13.8v
Amplifier Speaker Load RMS Power Current

Operating Voltage - 12.5v


Amplifier Speaker Load RMS Power Current

4 ohm stereo 4 ohm mono 2 ohm stereo 2 ohm mono

530W/ch 38A 1800W 59A 800W/ch 60A 2700W 105A

4 ohm stereo 4 ohm mono 2 ohm stereo 2 ohm mono

300W/ch 1000W 500W/ch 2000W

65A 105A 98A 210A

Note: No less than 0ga power and ground wire must be used in these wiring configurations. We also recommend the use of a 2 farad capacitor for optimized power delivery.
Ultimate Car Audio is not responsible for any damage that may occur to ones vehicle, as a result of improperly installed or configured amplifiers. Specifications subject to change. The data above is based on a controlled test bench environment. Test frequency is 100hz, at 1% THD.

You might also like