SAVITRIBAI PHULE PUNE UNIVERSITY

Booklet of Practical Skeleton Papers

For

S.Y.B.Sc (Computer Science)

Choice Based Credit System (CBCS)

Semester - III

Electronics Practical Examination

(From June 2022)

S.Y.B.Sc (Computer Science)

1
 CONTENTS
Page
Sr. No Title of the Experiment
No.
GROUP A (Any 5)

Arithmetic, logical & code conversion problems using assembly/C

A1 3
programming.
Interfacing of thumbwheel & seven segment display to 8051
A2 -
Microcontroller.
A3 Traffic light controller using 8051 microcontroller. 4
A4 Interfacing LCD to 8051Microcontroller 5
Waveform generation using DAC Interface to
A5 6
8051Microcontroller
Event counter using opto-coupler, seven segment LED/LCD
A6 -
display interface to 8051 microcontroller

A7 Speed Control of stepper motor using 8051 microcontroller 7

GROUP B (Any 5)
B1 Study of 3 or 4 Bit Pulse Code Modulation technique 8
B2 Study of Frequency Shift Keying 9
B3 Study of Time Division Multiplexing 10
B4 Study of Frequency Division Multiplexing 11
B5 Study of Code Division Multiple Access System -
B6 Study of Error detection and correction by using Hamming Code technique -
B7 Study of Computer network components : Cables, Connectors, Routers,
12
Switches, Ethernet and related interfacing cards
B8 To study Configuration of IP and MAC address 13

2
 SAVITRIBAI PHULE PUNE UNIVERSITY
S. Y. B. Sc. (Computer Science) Exam.Seat No._____
Electronics Practical Examination
Time Duration: 3 Hours Max. Marks: 35
Distribution of Marks

Flowchart/ Result Experiment

Algorithm Program Execution & Oral Total
Conclusion

05 10 10 05 05 35

Instructions to students:

1. Read slip carefully and write the program in assembly language.

2. Do not switch ON Computer without prior permission of examiner.
3. Show the result to the examiner.
4. Use of calculator is not allowed.
5. The 805 microcontroller manual will be provided on demand.

A1: Arithmetic, logical & code conversion problems using assembly /C Programming.

1. Write an algorithm / flowchart for addition of elements of two equal length array / Hex to
decimal conversion / Decimal to Hex conversion / To find largest or smallest element from an
array. Get it checked from the examiner.
2. Write an assembly/ C language program using 8051 instruction set and show it to the examiner.
3. Execute the program and show the Result to examiner.
4. Modify the program and verify the Result.
5. Write difference between Microprocessor and Microcontroller.
6. What is the use of DA A instruction in 8051 Microcontroller.

3
 SAVITRIBAI PHULE PUNE UNIVERSITY
S. Y. B. Sc. (Computer Science) Exam.Seat No._____
Electronics Practical Examination
Time Duration: 3 Hours Max. Marks: 35
Distribution of Marks

Flowchart/ Block Experiment

Execution
Algorithm diagram & Program Oral Total
&Result
connection

05 08 10 07 05 35

Instructions to students:
1. Read slip carefully and write the program in C Language.
2. Do not switch ON computer / circuit board without prior permission of examiner.
3. Before taking observations, get the circuit connections checked from the examiner.
4. Show the output to examiner.
5. Use of calculator is not allowed.
6. The 8051 manual will be provided on demand.

A3: Traffic light controller using 8051 Microcontroller.

1. Draw block diagram / circuit diagram of Traffic Light Control system using 8051
microcontroller.
2. Write an algorithm/ draw the flowchart for the same .Show it to Examiner.
3. Write Program in embedded C to control the Traffic of 4-way intersection using
Microcontroller.
4. Execute it and show execution result to the examiner.
5. Modify this program for night mode.

4
 Savitribai Phule Pune University Exam.Seat No._____

S. Y. B. Sc. (Comp.Sci.)
Electronics Practical Examination
Time Duration: 3 Hours Max Marks: 35
Distribution of Marks

Flowchart/ Block Experiment

Execution
Algorithm diagram & Program Oral Total
&Result
connection

05 08 10 07 05 35

Instructions to students:
1. Read slip carefully and write the program in C Language.
2. Do not switch ON computer / circuit board without prior permission of examiner.
3. Before taking observations, get the circuit connections checked from the examiner.
4. Show the output to examiner.
5. Use of calculator is not allowed.
6. The 8051 manual will be provided on demand.

A4: Interfacing LCD to 8051 Microcontroller.

1. Draw block diagram / Circuit diagram of LCD interfacing using 8051 microcontroller.
2. Write an algorithm /Draw the flowchart for the same. Show it to the examiner.
3. Write Program in embedded C to display …………. ,…………….. ,……….. on LCD.
4. Execute the Program and show execution result to the examiner.
5. What is the function of RS, R/Wand Enable pins of LCD?

5
 SAVITRIBAI PHULE PUNE UNIVERSITY
S. Y. B. Sc. (Computer Science) Exam.Seat No._____
Electronics Practical Examination
Time Duration: 3 Hours Max. Marks: 35
Distribution of Marks

Flowchart/ Block Experiment

Execution
Algorithm diagram & Program Oral Total
&Result
connection

05 08 10 07 05 35

Instructions to students:
1. Read slip carefully and write the program in C Language.
2. Do not switch ON computer / circuit board without prior permission of examiner.
3. Before taking observations, get the circuit connections checked from the examiner.
4. Show the output to examiner.
5. Use of calculator is not allowed.
6. The 8051 manual will be provided on demand.

A5 : Waveform generation using DAC Interface.

1. Draw block diagram/circuit diagram to generate square/triangular/saw tooth waveform using
DAC interfacing with 8051.
2. Write an algorithm/Draw the flowchart for the same. Show it to Examiner.
3. Write Program using embedded C.
4. Make the connections and get it checked by the examiner.
5. Execute the Program and show execution result to the examiner.
6. Take observations for amplitude and frequency measurement of each waveform using CRO.
7. Modify the program to increase/ decrease the amplitude or frequency of waveforms.

6
 SAVITRIBAI PHULE PUNE UNIVERSITY
S. Y. B. Sc. (Computer Science) Exam. Seat No._____
Electronics Practical Examination
Time Duration: 3 Hours Max. Marks: 35
Distribution of Marks

Flowchart/ Block Experiment

Execution
Algorithm diagram & Program Oral Total
&Result
connection

05 08 10 07 05 35

Instructions to students:
1. Read slip carefully and write the program in C Language.
2. Do not switch ON computer / circuit board without prior permission of examiner.
3. Before taking observations, get the circuit connections checked from the examiner.
4. Show the output to examiner.
5. Use of calculator is not allowed.
6. The 8051 manual will be provided on demand.

A7: Speed Control of stepper motor using microcontroller.

1. Draw block diagram to interface stepper motor with 8051 Microcontroller.
2. Write an algorithm/ Draw the flowchart for the same. Show it to Examiner.
3. Write Program in embedded C.
4. Make the connections and get it checked by the examiner.
5. Execute the Program and show execution result to the examiner.
6. Change the direction of stepper motor rotation and verify the result.
7. Define step angle and step angle if steps per revolutions are………..

7
 SAVITRIBAI PHULE PUNE UNIVERSITY
S. Y. B. Sc. (Computer Science) Exam.Seat No._____
Electronics Practical Examination
Time Duration: 3 Hours Max. Marks: 35
Distribution of Marks

Circuit
Observations Experiment
/Block Graph, Result &
Connection & Oral Total
Diagram Conclusion
Calculations

08 05 12 05 05 35

Instructions to students:
1. Read slip carefully and write and perform the experiment accordingly.
2. Do not switch ON any instrument / circuit board without prior permission of examiner.
3. Before taking observations, get the circuit connections checked from the examiner.
4. Show at least one observation to examiner.
5. Use of only non programmable calculator is allowed.
6. IC manual will be provided on demand.

B1: Study of 3 or 4 bit Pulse Code Modulation Technique (PCM)

1. Draw circuit diagram /block diagram of ¾-bit pulse code modulation (PCM) and get checked
from examiner.
2. Draw observation table to measure modulating signal and clock signal.
3. Connect circuit as per diagram and show to examiner.
4. Adjust the modulating signal and clock signal for proper PCM output signal.
5. Draw the waveform of PAM signal and PCM output signal.
6. Write need of sample and Hold circuit in PCM Modulator.
7. Why level shifting is necessary in PCM system.
8. “PCM is a digital Modulation technique” comment.

8
 SAVITRIBAI PHULE PUNE UNIVERSITY
S. Y. B. Sc. (Computer Science) Exam.Seat No._____
Electronics Practical Examination
Time Duration: 3 Hours Max. Marks: 35
Distribution of Marks

Circuit
Observations Experiment
/Block Graph, Result &
Connection & Oral Total
Diagram Conclusion
Calculations

08 05 12 05 05 35

Instructions to students:
1. Read slip carefully and write and perform the experiment accordingly.
2. Do not switch ON any instrument / circuit board without prior permission of examiner.
3. Before taking observations, get the circuit connections checked from the examiner.
4. Show at least one observation to examiner.
5. Use of only non programmable calculator is allowed.
6. IC manual will be provided on demand.

B2: Build and test Time Division Multiplexing (TDM) circuit.

1. Draw the circuit diagram of 2:1 TDM and get it checked from examiner.
2. Make the connections and get them checked from examiner.
3. Measure the input signal Frequencies and control signal frequency using CRO.
4. Calculate the input signal frequencies and control signal frequency using standard formula.
5. Show the TDM output to the examiner.
6. Note down the readings in observation table and draw the necessary timing diagram.
7. Write any four applications of TDM.

9
 SAVITRIBAI PHULE PUNE UNIVERSITY
S. Y. B. Sc. (Computer Science) Exam.Seat No._____
Electronics Practical Examination
Time Duration: 3 Hours Max. Marks: 35
Distribution of Marks

Circuit
Observations Experiment
/Block Graph, Result &
Connection & Oral Total
Diagram Conclusion
Calculations

08 05 12 05 05 35

Instructions to students:
1. Read slip carefully and write and perform the experiment accordingly.
2. Do not switch ON any instrument / circuit board without prior permission of examiner.
3. Before taking observations, get the circuit connections checked from the examiner.
4. Show at least one observation to examiner.
5. Use of only non programmable calculator is allowed.
6. IC manual will be provided on demand.

B3: Build and test Frequency Shift Keying (FSK) circuit.

1. Draw the circuit diagram of FSK and get it checked from the examiner.
2. Make the connections and get them checked.
3. Identify the modulating signal and modulated signal and show them to the examiner on CRO.
4. Measure the mark and space frequencies.
5. What is FSK? Write any two application of FSK.

10
 SAVITRIBAI PHULE PUNE UNIVERSITY
S. Y. B. Sc. (Computer Science) Exam.Seat No._____
Electronics Practical Examination
Time Duration: 3 Hours Max. Marks: 35
Distribution of Marks

Circuit
Observations Experiment
/Block Graph, Result &
Connection & Oral Total
Diagram Conclusion
Calculations

08 05 12 05 05 35

Instructions to students:
1. Read slip carefully and write and perform the experiment accordingly.
2. Do not switch ON any instrument / circuit board without prior permission of examiner.
3. Before taking observations, get the circuit connections checked from the examiner.
4. Show at least one observation to examiner.
5. Use of only non programmable calculator is allowed.
6. IC manual will be provided on demand.

B4: Study of Frequency Division Multiplexing (FDM) circuit.

1. Draw the block diagram of Frequency Division Multiplexing (FDM) circuit and get it checked
from examiner.
2. Draw observation table to measure modulating input signal, Carrier input signal and modulated
output signals.
3. Connect circuit and show to examiner.
4. Adjust the modulating signal & carrier signal for both balanced modulator circuits to get proper
AM output on CRO.
5. Draw the waveform of FDM output.
6. List the types of multiplexing technique & its applications.
7. What is the use of Linear Adder/ Mixer in FDM circuit?

11
 SAVITRIBAI PHULE PUNE UNIVERSITY
S. Y. B. Sc. (Computer Science) Exam.Seat No._____
Electronics Practical Examination
Time Duration: 3 Hours Max. Marks: 35
Distribution of Marks

Circuit
Observations Experiment
/Block Graph, Result &
Connection & Oral Total
Diagram Conclusion
Calculations

08 05 12 05 05 35

Instructions to students:
1. Read slip carefully and write and perform the experiment accordingly.
2. Do not switch ON any instrument / circuit board without prior permission of examiner.
3. Before taking observations, get the circuit connections checked from the examiner.
4. Show at least one observation to examiner.
5. Use of only non programmable calculator is allowed.
6. IC manual will be provided on demand.

B7: Study of Computer network Components: Cables, Connectors, Routers, Switches, Ethernet
and related interfacing cards

1. Draw the block of computer network using network components.

2. Transfer files between two systems in a LAN. Show it to the examiner.
3. List the names of the network topologies.
4. List different types of cables. Explain any one type.
5. Explain role of Router, Switches and Ethernet.
6. What is NICs? Write its use.
7. Explain Gateway?

12
 SAVITRIBAI PHULE PUNE UNIVERSITY
S. Y. B. Sc. (Computer Science) Exam.Seat No._____
Electronics Practical Examination
Time Duration: 3 Hours Max. Marks: 35
Distribution of Marks

Circuit/Block Observations Experiment

Graph, Result &
Diagram Connection & Oral Total
Conclusion
Calculations

08 05 12 05 05 35

Instructions to students:
1. Read slip carefully and write and perform the experiment accordingly.
2. Do not switch ON any instrument / circuit board without prior permission of examiner.
3. Before taking observations, get the circuit connections checked from the examiner.
4. Show at least one observation to examiner.
5. Use of only non programmable calculator is allowed.
6. IC manual will be provided on demand.

B8 : To study configuration of IP and MAC Address and to study Local Area Network setup.

1. Draw the block of computer network using network components.

2. Write the steps to configure IP Address, Subnet mask and Default Gateway.
3. Configure Internet connection using IPCONFIG and PING commands.
4. Show the established wired or wireless LAN connection to the examiner.
5. List the names of the network topologies.
6. List different network devices and explain any two of them.

13