XL6007

400KHz 60V 2A Switching Current Boost / Buck-Boost / Inverting DC/DC Converter

Features General Description

„ Wide 3.6V to 24V Input Voltage Range The XL6007 regulator is a wide input range,
„ Positive or Negative Output Voltage current mode, DC/DC converter which is
Programming with a Single Feedback Pin capable of generating either positive or
„ Current Mode Control Provides Excellent negative output voltages. It can be configured
Transient Response as either a boost, flyback, SEPIC or inverting
„ 1.25V reference adjustable version converter. The XL6007 built in N-channel
„ Fixed 400KHz Switching Frequency power MOSFET and fixed frequency
„ Maximum 2A Switching Current oscillator, current-mode architecture results in
„ SW PIN Built in Over Voltage Protection stable operation over a wide range of supply
„ Excellent line and load regulation and output voltages.
„ EN PIN TTL shutdown capability The XL6007 regulator is special design for
„ Internal Optimize Power MOSFET portable electronic equipment.
„ High efficiency up to 90%
„ Built in Frequency Compensation
„ Built in Soft-Start Function
„ Built in Thermal Shutdown Function
„ Built in Current Limit Function
„ Available in SOP8L package

Applications
„ Automotive and Industrial Boost /
Buck-Boost / Inverting Converters
„ Portable Electronic Equipment

Figure1. Package Type of XL6007

Rev 1.2 www.xlsemi.com

1
 XL6007

400KHz 60V 2A Switching Current Boost / Buck-Boost / Inverting DC/DC Converter

Pin Configurations

EN 1 8 GND

VIN 2 7 GND
XL6007
FB 3 6 SW

NC 4 5 SW

Figure2. Pin Configuration of XL6007 (Top View)

Table 1 Pin Description

Pin Number Pin Name Description

Enable Pin. Drive EN pin low to turn off the device, drive it
1 EN
high to turn it on. Floating is default high.
Supply Voltage Input Pin. XL6007 operates from a 3.6V to 24V
2 VIN DC voltage. Bypass Vin to GND with a suitably large capacitor
to eliminate noise on the input.
3 FB Feedback Pin (FB). The feedback threshold voltage is 1.25V.
4 NC No Connected.
Power Switch Output Pin (SW). Output is the switch node that
5,6 SW
supplies power to the output.
7,8 GND Ground Pin.

Rev 1.2 www.xlsemi.com

2
 XL6007

400KHz 60V 2A Switching Current Boost / Buck-Boost / Inverting DC/DC Converter

Function Block

Figure3. Function Block Diagram of XL6007

Typical Application Circuit

Figure4. XL6007 Typical Application Circuit (Boost Converter)

Rev 1.2 www.xlsemi.com

3
 XL6007

400KHz 60V 2A Switching Current Boost / Buck-Boost / Inverting DC/DC Converter

Ordering Information
Order Information Marking ID Package Type Packing Type Supplied As
XL6007E1 XL6007E1 SOP8L 2500 Units on Tape & Reel
XLSEMI Pb-free products, as designated with “E1” suffix in the par number, are RoHS compliant.

Absolute Maximum Ratings（Note1）

Parameter Symbol Value Unit
Input Voltage Vin -0.3 to 26 V
Feedback Pin Voltage VFB -0.3 to Vin V
EN Pin Voltage VEN -0.3 to Vin V
Output Switch Pin Voltage VOutput -0.3 to 60 V
Power Dissipation PD Internally limited mW
Thermal Resistance (SOP-8L)
RJA 100 ºC/W
(Junction to Ambient, No Heatsink, Free Air)
Operating Junction Temperature TJ -40 to 125 ºC
Storage Temperature TSTG -65 to 150 ºC
Lead Temperature (Soldering, 10 sec) TLEAD 260 ºC
ESD (HBM) >2000 V

Note1: Stresses greater than those listed under Maximum Ratings may cause permanent damage
to the device. This is a stress rating only and functional operation of the device at these or any
other conditions above those indicated in the operation is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect reliability.

Rev 1.2 www.xlsemi.com

4
 XL6007

400KHz 60V 2A Switching Current Boost / Buck-Boost / Inverting DC/DC Converter

XL6007 Electrical Characteristics

Ta = 25℃;unless otherwise specified.
Symbol Parameter Test Condition Min. Typ. Max. Unit
System parameters test circuit figure4
Feedback Vin = 12V to 16V, Vout=18V
VFB 1.213 1.25 1.287 V
Voltage Iload=0.1A to 0.5A
Vin=12V ,Vout=18.5V
Efficiency ŋ - 90 - %
Iout=0.5A

Electrical Characteristics (DC Parameters)

Vin = 12V, GND=0V, Vin & GND parallel connect a 220uf/50V capacitor; Iout=0.5A, Ta =
25℃; the others floating unless otherwise specified.
Parameters Symbol Test Condition Min. Typ. Max. Unit
Input operation voltage Vin 3.6 24 V
Shutdown Supply Current ISTBY VEN=0V 70 100 uA
VEN =2V,
Quiescent Supply Current Iq 2.5 5 mA
VFB =Vin
Oscillator Frequency Fosc 320 400 480 Khz

Switch Current Limit IL VFB =0 2 A

Vin=12V,
Output Power NMOS Rdson 110 120 mohm
ISW=2A

High (Regulator ON) 1.4

EN Pin Threshold VEN V
Low (Regulator OFF) 0.8

EN Pin Input Leakage IH VEN =2V (ON) 3 10 uA

Current IL VEN =0V (OFF) 3 10 uA

Max. Duty Cycle DMAX VFB=0V 90 %

Rev 1.2 www.xlsemi.com

5
 XL6007

400KHz 60V 2A Switching Current Boost / Buck-Boost / Inverting DC/DC Converter

Schottky Diode Selection Table

Current Surface Through VR (The same as system maximum input voltage)
Mount Hole
20V 30V 40V 50V 60V
1A √ 1N5817 1N5818 1N5819

√ 1N5820 1N5821 1N5822

√ MBR320 MBR330 MBR340 MBR350 MBR360
√ SK32 SK33 SK34 SK35 SK36
3A
√ 30WQ03 30WQ04 30WQ05
√ 31DQ03 31DQ04 31DQ05
√ SR302 SR303 SR304 SR305 SR306

Typical System Application – Boost (Output 18.5V/0.5A)

Figure5. XL6007 Typical System Application (Boost Converter)

Rev 1.2 www.xlsemi.com

6
 XL6007

400KHz 60V 2A Switching Current Boost / Buck-Boost / Inverting DC/DC Converter

Typical System Application – SEPIC Buck-Boost (Input 10V~18V, Output 12V/0.5A)

Figure6. XL6007 Typical System Application (SEPIC Buck-Boost Converter)

Typical System Application for Inverting Converter
– SEPIC Inverting Topology (Input 10V~18V, Output + -12V/0.6A)
VOUT -12V
COUT
L1C 220uf/50V
D1 1N5822

CDC 22uf/50V

VOUT +12V
D1 1N5822
L1A L1B

CDC 22uf/50V
SW R2 8.6K
5,6
VIN FB
2 XL6007 3
COUT
7,8 1
105 220uf/50V
GND EN R1 1K
VIN
CIN 105 ON
47uf /50V OFF

SEPIC + - Converter
Input 10V ~ 18V
Output +-12V / 0.6A
VOUT=1.25*(1+R2/R1)

Figure7. XL6007 Typical System Application (SEPIC Inverting Converter)

Rev 1.2 www.xlsemi.com

7
 XL6007

400KHz 60V 2A Switching Current Boost / Buck-Boost / Inverting DC/DC Converter

Package Information

SOP8 Package Mechanical Dimensions

Rev 1.2 www.xlsemi.com

8