Installation Guide

Speed gates SBTL8000 series

Applicable Model(s): SBTL8000, SBTL8011, SBTL8022, SBTL8033,
SBTL8200, SBTL8211, SBTL8222, SBTL8233
Version: 1.0
Date: June 2019
1 Preparation

1. Tools: a measuring tape, an adjustable wrench, an impact drill and a small screwdriver (included
in the package).
2. Material: a PVC anti-fire and insulation tube (diameter≥25mm), standard three-core power
extension wire, tether cable (random configuration), M12 expansion screws (included in the
package).
3. Thread the connection wire of the device through the tube before assembly.
4. The power and signal wires should be set separately to easily distinguish strong and weak power.
Please invite professional personnel to complete the wiring. The device must be connected to
the ground.
Below is the outline and dimensions of SBTL8000:

Figure 1-1

SBTL8000 series installation guide 1

2 Installation

1. Prepare the tools for product installation and sort out the auxiliaries according to the packing list.
2. Drill holes after determining the hole positions based on the mounting template as shown in
Figure 2-1. Insert the expansion bolt into the holes accordingly.

Figure 2-1

3. Tighten the nut preliminarily, then connect the master and slave devices with wires.
4. Test the operations of the device after connecting it to the power supply with the temporary
cable. Make sure that the ground wire of AC power is connected to the cabinet of the device.
5. Turn on the air switch to test whether the device is working properly. Wait for 10 seconds for the
turnstile to complete the self-test program. At the same time, check if the indicators work
properly. If everything works fine, you can fasten the ground screw nuts and fix the device. If an
exception occurs, please contact your vendor.

2 SBTL8000 series installation guide

3 Debugging Functions
 Operating instruction

1. After powered on, the LCD screen on the control board will display the default state showing the
current working mode.
2. There are 4 buttons on the control board: UP, DOWN, ENT, and ESC, as shown in Figure 3-1.
UP: to move upwards or increase the value.
DOWN: to move downwards or decrease the value.
ENT: to enter a menu setting item or confirm the current modified value.
ESC: to return to the previous menu or cancel the current operation.

 Menus

1. Position adjustment of the swing barrier

Type: zero (default)

Left limit
Right limit

2. Passing mode

Opening mode: Two-way swipe (default)

Left free, Right swipe
Left swipe, Right free
Two-way free
Left prohibit, Right swipe
Left swipe, Right prohibit
Left prohibit, Right free
Left free, Right prohibit
Two-way prohibit

3. Opening duration (Press ‘ENT’ to modify)

After the gate is opened, it will automatically close if no one passes through within a certain time
duration. The default value is 5 seconds. The value ranges from 2 to 60.

SBTL8000 series installation guide 3

4. Reverse intrusion

Mode: Close the door and voice alarm

Voice alarm only (default)
Turn off reverse detection

5. Trailing alarm detection

Mode: Turn off trailing detection

Voice alarm only (default)
Close the door and voice alarm

6. Opening speed

Speed value: 1~20 (default 1)

7. Closing speed

Speed value: 1~20 (default 1)

8. Swiping mode

Method: Allow the card to be swiped in the channel (default)

Do not allow card swiping in the channel

9. Reset counter

Reset: Out counter (default)

Into the counter
All

10. Gate closing delay time

Time: 0~10 (default 0)

11. Brake unlock mode

Mode: Delay unlock (default)

12. Brake starting angle

Angle: 1~10 (default 3)

13. Fire alarm signal

Signal: right open

4 SBTL8000 series installation guide

 Left open (default)
Shut down

14. Volume setting

Volume: off
The value ranges from 1 to 16 (default 5).
1 is the minimum value; 16 is the maximum value.

15. Audio prompt for gate opening swift

Enable or not: No (default)

Yes

16. Infrared anti-pinch

Mode: Turn off the anti-pinch feature

Enabling anti-pinch (default)

17. Infrared anti-pinch area

Area selection: Disable during In and out of infrared (default)

All infrared zone anti-pinch

18. Memory opening

Whether to open: No (default)

Yes

19. System working mode

Mode: working mode (default)

Test mode
Restore to factory

20. Version number:

Version: V9.0.0

SBTL8000 series installation guide 5

4 Troubleshooting

Number Failure descriptions Analysis and solution

The mode indicator light does not respond Check that the control panel mode indicator
1
or the indication is incorrect. wiring is correct or that the contact is poor.

Check the mode setting of the master and

After swiping the card, there is only a speed slave devices and the 8-core, 2-core
2
gate unlocked. connection lines. See the wiring diagram for
the specific connection circuit.

The barrier doesn’t close when the opening Check to see if the opening delay time is too
3
delay time is ended. long or whether the IR sensor is covered.

In the process of self-test, there are obstacles,

When the gate is self-tested, the swing arm
4 please remove the obstacles, restart the self-
is not in the normal closing position!
test after power-on!

6 SBTL8000 series installation guide

5 Wiring Diagram

Below is the wiring diagram:

Figure 5-1

SBTL8000 series installation guide 7

ZK Building, Wuhe Road, Gangtou, Bantian, Buji Town,
Longgang District, Shenzhen China 518129
Tel: +86 755-89602345
Fax: +86 755-89602394
www.zkteco.com

8 SBTL8000
Copyright©2019 series
ZKTECO CO.,installation
LTD. All rights guide
reserved.