60W Single Output Industrial DIN Rail Power Supply MDR-60 series

User’s Manual
■ Features :
Universal AC input/Full range
Protections: Short circuit / Overload / Over voltage
Cooling by free air convection
Can be installed on DIN rail TS-35/7.5 or 15
Class I, Div 2 Hazardous Locations T4
LED indicator for power on
DC OK relay contact
No load power consumption<0.75W
100% full load burn-in test
■ GTIN CODE 3 years warranty
MW Search: https://www.meanwell.com/serviceGTIN.aspx Bauar t gepruft
Sicherheit
egel ma ge
od o s
THOMAS SAMUEL
THOMAS SAMUEL

be wac g

(except 48V) www.tuv.com

SPECIFICATION
ID 2000000000
R33100
UL62368-1 RoHS TPTC004 IS13252 BS EN/EN62368-1 IEC62368-1

MODEL MDR-60-5 MDR-60-12 MDR-60-24 MDR-60-48

DC VOLTAGE 5V 12V 24V 48V
RATED CURRENT 10A 5A 2.5A 1.25A
CURRENT RANGE 0 ~ 10A 0 ~ 5A 0 ~ 2.5A 0 ~ 1.25A
RATED POWER 50W 60W 60W 60W
RIPPLE & NOISE (max.) Note.2 80mVp-p 120mVp-p 150mVp-p 200mVp-p
OUTPUT VOLTAGE ADJ. RANGE 5 ~ 6V 12 ~ 15V 24 ~ 30V 48 ~ 56V
VOLTAGE TOLERANCE Note.3 ±2.0% ±1.0% ±1.0% ±1.0%
LINE REGULATION ±1.0% ±1.0% ±1.0% ±1.0%
LOAD REGULATION ±1.5% ±1.0% ±1.0% ±1.0%
SETUP, RISE TIME Note.5 500ms, 30ms/230VAC 500ms, 30ms/115VAC at full load
HOLD UP TIME (Typ.) 50ms/230VAC 20ms/115VAC at full load
VOLTAGE RANGE 85 ~ 264VAC 120 ~ 370VDC
FREQUENCY RANGE 47 ~ 63Hz
EFFICIENCY (Typ.) 78% 85% 87% 87%
INPUT
AC CURRENT (Typ.) 1.8A/115VAC 1A/230VAC
INRUSH CURRENT (Typ.) COLD START 30A/115VAC 60A/230VAC
LEAKAGE CURRENT <1mA / 240VAC
105 ~ 150% rated output power
OVERLOAD
Protection type : Constant current limiting, recovers automatically after fault condition is removed
PROTECTION
6.25 ~ 7.25V 15.6 ~ 18V 31.2 ~ 36V 57.6 ~ 64.8V
OVER VOLTAGE
Protection type : Shut down o/p voltage, re-power on to recover
FUNCTION DC OK SIGNAL Relay contact rating(max.): 30V/1A resistive
WORKING TEMP. -20 ~ +70℃ (Refer to "Derating Curve")
WORKING HUMIDITY 20 ~ 90% RH non-condensing
ENVIRONMENT STORAGE TEMP., HUMIDITY -40 ~ +85℃, 10 ~ 95% RH
TEMP. COEFFICIENT ±0.03%/℃ (0 ~ 50℃)
VIBRATION Component : 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes ; Mounting : Compliance to IEC60068-2-6
SAFETY STANDARDS Ul508, UL62368-1, TUV BS EN/EN62368-1,Class I, Div. 2 Group A, B, C, D Hazardous Locations T4, EAC TP TC 004,
BSMI CNS14336-1, AS/NZS 60950.1 , IS13252(Part1)/IEC60950-1(except 48V) approved
SAFETY & WITHSTAND VOLTAGE I/P-O/P:3KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC
EMC ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:>100M Ohms / 500VDC / 25℃/ 70% RH
(Note 4) EMC EMISSION Compliance to BS EN/EN55032 (CISPR32), BS EN/EN61204-3 Class B, BS EN/EN61000-3-2,-3, EAC TP TC 020, CNS13438 Class B
Compliance to BS EN/EN61000-4-2, 3, 4, 5, 6, 8, 11, BS EN/EN55035, BS EN/EN61000-6-2, BS EN/EN61204-3, heavy industry level,
EMC IMMUNITY EAC TP TC 020
MTBF 2355.2K hrs min. Telcordia SR-332 (Bellcore) ; 489.9K hrs min. MIL-HDBK-217F (25℃)
OTHERS DIMENSION 40*90*100mm (W*H*D)
PACKING 0.33Kg; 42pcs/14.8Kg/0.82CUFT
NOTE 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1μF & 47μF parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives. For guidance on how to perform these EMC tests, please refer to “EMI testing of component power supplies.”
(as available on https://www.meanwell.com//Upload/PDF/EMI_statement_en.pdf )
5. Length of set up time is measured at first cold start. Turning ON/OFF the power supply may lead to increase of the set up time.
6. The ambient temperature derating of 3.5℃/1000m with fanless models and of 5℃/1000m with fan models for operating altitude higher than 2000m(6500ft).
※ Product Liability Disclaimer：For detailed information, please refer to https://www.meanwell.com/serviceDisclaimer.aspx

File Name:MDR-60-SPEC 2024-02-19

 60W Single Output Industrial DIN Rail Power Supply MDR-60 series

Mechanical Specification Case No.962A Unit:mm

35 40 100
5 5 5 5 5

+V +V -V -V
DC OK

DC OK
+
+V ADJ
90

N L

7.5 7.5
Install DIN rail TS35/7.5 or TS35/15

Block Diagram
fosc : 60KHz

DC OK

RECTIFIERS RECTIFIERS +V
EMI POWER
I/P & &
FILTER SWITCHING -V
FILTER FILTER
O.C.P.

FG DETECTION
CIRCUIT
O.L.P. CONTROL
O.V.P.
DC OK Relay Contact

Contact Close PSU turns on / DC OK.

Contact Open PSU turns off / DC Fail.
Contact Ratings (max.) 30V/1A resistive load.

Derating Curve Output Derating VS Input Voltage

100
100
12V,24V,48V
90
80
80

60 70
50
LOAD (%)

5V
LOAD (%)

60
40
50
20
40

-20 0 10 20 30 45 55 60 70 (VERTICAL) 85 95 100 115 120 140 160 180 200 220 240 264

AMBIENT TEMPERATURE (℃) INPUT VOLTAGE (VAC) 60Hz

File Name:MDR-60-SPEC 2024-02-19