Scribd
Upload
180 views8 pages

Spark LINK User Manual

Uploaded by

Hilton
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
180 views8 pages

Spark LINK User Manual

Uploaded by

Hilton
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 8

Spark LINK

User Manual
Table of Contents
02 Product Specifications

02 What’s In The Box?

04 Get Started

05 Operation

06 Charging Spark LINK

06 Auto Power Management

07 Manual Power Reset

1
Product Specifications

● Frequency range: 2.4GHz

● Sample rate: 24-bit, 48 kHz

● Frequency response: 20 Hz - 20 kHz

● Dynamic range: 96 dB

● Latency: < 3ms

● Line of sight range: 70ft (21 meters)

● Battery life: up to 6 hours of continuous use

● Charging time: approx. 2 hours

What’s In The Box?

● Spark LINK TX – Transmitter that plugs into your guitar.

2
● Spark LINK RX – Receiver that plugs into your amp.

● USB-A to USB-C charging cable.

● Quick Start Guide and Safety Instructions.

3
Get Started

● Connect The Transmitter (TX) To Your Guitar

1. Plug Spark LINK TX into the output jack of your guitar.


2. Adjust the hinge so that Spark LINK TX sits comfortably on your
guitar.
3. Press and hold the button to turn on.

● Connect The Receiver (RX) To An Amp or Effect Pedal

1. Plug Spark LINK RX into the input of your amp or effect pedal.
2. Press and hold the button to turn on.

4
Operation

● Pairing Spark LINK We TX and Spark LINK RX


Spark LINK TX and Spark LINK RX will automatically pair once both
are turned on. The LED will flash blue while pairing and once paired,
will show battery status. You can connect up to four Spark LINK
setups for simultaneous jamming within the same space.

● Re-Pairing Spark LINK TX and Spark LINK RX


While both powered on, double-press the button on Spark LINK TX to
scan and re-pair to Spark LINK RX.

● Muting Spark LINK


Quick-press the Power button on Spark LINK TX to mute and
unmute. The LED will flash yellow and green.

● LED Indicator
The LED will flash blue while pairing and once paired, will show
battery status.

LED Color Status

Blue TX / RX Pairing / Connecting

Green Battery Level : 60% - 100%

Yellow Battery Level : 6% - 60%

Red Battery Level : Below 5%

5
Charging Spark LINK
Plug Spark LINK TX and Spark LINK RX into a USB power supply
with the USB cable provided. It is recommended the power supply be
5V-1A.

While charging, the LED indicator on both devices will display battery
level.

LED Color Charge Status

Flashing Red Below 5%

Flashing Yellow 6% - 60%

Flashing Green 60% - 99%

Solid Green 100%

Auto Power Management


If there's no signal for 15 minutes, Spark LINK TX will automatically
turn off to conserve battery. Spark LINK RX will likewise turn off after
15 seconds if it detects no connection to Spark LINK TX.

6
Manual Power Reset
If you encounter any issues with Spark LINK that render it unusable
or shut down properly, you can resolve the issue by performing a
manual power reset:

1. Locate the reset button inside the small hole on the side of Spark
LINK.

2. Use a needle or paperclip to gently insert into the reset button hole.
Press the reset button once to reset power.

You might also like