2006 VA Powertrain Sprinter

TABLE OF CONTENTS
1.0 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 1.1 1.2 2.0 3.0 SYSTEM COVERAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 SIX-STEP TROUBLESHOOTING PROCEDURE . . . . . . . . . . . . . . . . . . . . . . . . . .1
IDENTIFICATION OF SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 SYSTEM DESCRIPTION AND FUNCTIONAL OPERATION . . . . . . . . . . . . . . . . . . . . . .1 3.1 3.2 GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 FUNCTIONAL OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 3.2.1 ECM ON-BOARD DIAGNOSTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 3.2.2 ECM OPERATING MODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 3.2.3 MONITORED CIRCUITS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 3.2.4 SKREEM OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 3.2.5 SKREEM ON-BOARD DIAGNOSTICS. . . . . . . . . . . . . . . . . . . . . . . . . . .2 3.2.6 SKREEM OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 DIAGNOSTIC TROUBLE CODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 3.3.1 HARD CODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 3.3.2 INTERMITTENT CODE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 3.3.3 ECM DIAGNOSTIC TROUBLE CODES. . . . . . . . . . . . . . . . . . . . . . . . . .3 3.3.4 HANDLING NO TROUBLE CODE PROBLEMS . . . . . . . . . . . . . . . . . . .8 USING THE DRBIII . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 3.4.1 DRBIII DOES NOT POWER UP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 3.4.2 DISPLAY IS NOT VISIBLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
3.3
3.4
4.0
DISCLAIMERS, SAFETY, WARNINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 4.1 4.2 DISCLAIMERS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 4.2.1 TECHNICIAN SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . .8 4.2.2 VEHICLE PREPARATION FOR TESTING. . . . . . . . . . . . . . . . . . . . . . . .9 4.2.3 SERVICING SUB-ASSEMBLIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 4.2.4 DRBIII SAFETY INFORMATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 WARNINGS AND CAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 4.3.1 ROAD TEST WARNINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 4.3.2 VEHICLE DAMAGE CAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
4.3
5.0 6.0 7.0
REQUIRED TOOLS AND EQUIPMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 GLOSSARY OF TERMS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 DIAGNOSTIC INFORMATION AND PROCEDURES . . . . . . . . . . . . . . . . . . . . . . . . . . .11 COMMUNICATION *NO RESPONSE FROM ENGINE CONTROL MODULE . . . . . . . . . . . . . . . . . . . . . . . .12 *NO RESPONSE FROM SENTRY KEY REMOTE ENTRY MODULE . . . . . . . . . . . . . .14 DRIVEABILITY - DIESEL P-1105 ATMOSPHERIC PRESSURE SENSOR PLAUSIBILITY WITH BOOST PRESSURE SENSOR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 P1105-ATMOSPHERIC PRESSURE SENSOR SIGNAL VOLTAGE TOO HIGH . . . . . .16 P1105-ATMOSPHERIC PRESSURE SENSOR SIGNAL VOLTAGE TOO LOW . . . . . .16 P1617- ECM READ/WRITE ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
i
TABLE OF CONTENTS - Continued

P1617- ECM WRITE ERROR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 P1617-ECM INCORRECT VALUE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 P1617-ECM READ ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 P2122-INTERNAL ERROR COUNTER FAULT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 P2122-INTERNAL ERROR ENGINE SHUT OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 P2122-INTERNAL ERROR ENGINE VOLTAGE MONITORING . . . . . . . . . . . . . . . . . . .16 P2122-INTERNAL ERROR ENGINE VOLTAGE MONITORING . . . . . . . . . . . . . . . . . . .16 P2123-INJECTOR BANK ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 P2124-INJECTOR BANK ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 P2139-ECM INJECTOR OUTPUT STAGE #1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 P2139-ECM INJECTOR OUTPUT STAGE #1 SHORT CIRCUIT . . . . . . . . . . . . . . . . . .16 P2140-ECM INJECTOR OUTPUT STAGE #2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 P2140-ECM INJECTOR OUTPUT STAGE #2 SHORT CIRCUIT . . . . . . . . . . . . . . . . . .16 P2149-ECM A/D CONVERTER HIGH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 P2149-ECM A/D CONVERTER LOW. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 P2149-ECM A/D CONVERTER PLAUSIBILITY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 P2153-STARTER RELAY CIRCUIT ECM THERMAL OVERLOAD . . . . . . . . . . . . . . . .16 P2197-FUEL QUANTITY SOLENOID ECM THERMAL OVERLOAD . . . . . . . . . . . . . . .16 P2214-CAN MESSAGE ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 P2319-ECM INTERNAL ERROR 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 P2319-ECM INTERNAL ERROR 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 P2319-ECM INTERNAL ERROR 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 P2319-ECM INTERNAL ERROR 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 P2321-ECM INTERNAL ERROR 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 P2323-ECM INTERNAL ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 P2324-ECM INJECTOR MONITORING 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 P2324-ECM INJECTOR MONITORING 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 P2324-ECM INJECTOR MONITORING 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 P2324-ECM INJECTOR MONITORING 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 P2324-ECM INJECTOR UNDERVOLTAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 P2325-ECM INTERNAL ERROR 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 P2325-ECM INTERNAL ERROR 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 P2325-ECM INTERNAL ERROR 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 P2325-ECM INTERNAL ERROR 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 P2329-ECM INTERNAL ERROR 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 P2330-ECM INTERNAL ERROR 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 P2340-ECM INJECTION QUANTITY ERROR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 P2342-ECM INTERNAL ERROR 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 P2342-ECM INTERNAL ERROR 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 P2350-INTERNAL VOLTAGE ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 P2352-INJECTION FAULT - EXCESSIVE TEMPERATURE . . . . . . . . . . . . . . . . . . . . . .17 P2352-INJECTION FAULT - QUANTITY ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 P2352-INJECTION FAULT - TORQUE LIMIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 P2352-INJECTION FAULT EXCESSIVE ENGINE SPEED . . . . . . . . . . . . . . . . . . . . . . .17 P2354-ECM INTERNAL FAULT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 P2356-ECM INTERNAL ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 P2357-ECM INTERNAL ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 P2358-ECM INTERNAL ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 P2500-FUEL PRESSURE SOLENOID CIRCUIT EXCESSIVE CURRENT . . . . . . . . . .17 P2514-CRANKCASE VENT HEATER EXCESSIVE CURRENT . . . . . . . . . . . . . . . . . . .17 P2526-BOOST PRESSURE SERVO MOTOR EXCESSIVE CURRENT . . . . . . . . . . . .17 P2527-EGR VALVE EXCESSIVE CURRENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 P0100-MASS AIR FLOW SENSOR SIGNAL VOLTAGE TOO LOW . . . . . . . . . . . . . . .19
ii

P0100-MASS AIR FLOW SENSOR SIGNAL VOLTAGE TOO LOW . . . . . . . . . . . . . . .19 P2011-MASS AIR FLOW SENSOR PLAUSIBILITY AIR MASS TOO HIGH . . . . . . . . .19 P2011-MASS AIR FLOW SENSOR PLAUSIBILITY AIR MASS TOO LOW . . . . . . . . . .19 P2024-MASS AIR FLOW SENSOR SIGNAL VOLTAGE TOO HIGH . . . . . . . . . . . . . . .19 P2024-MASS AIR FLOW SENSOR SIGNAL VOLTAGE TOO LOW . . . . . . . . . . . . . . .19 P2065-MASS AIR FLOW SENSOR SUPPLY VOLTAGE TOO HIGH. . . . . . . . . . . . . . .19 P2065-MASS AIR FLOW SENSOR SUPPLY VOLTAGE TOO LOW . . . . . . . . . . . . . . .19 P2067-MASS AIR FLOW SENSOR SIGNAL CIRCUIT OPEN OR SHORTED . . . . . . .19 P2067-MASS AIR FLOW SENSOR SIGNAL VOLTAGE TOO HIGH . . . . . . . . . . . . . . .19 P2067-MASS AIR FLOW SENSOR SIGNAL VOLTAGE TOO LOW . . . . . . . . . . . . . . .19 P2068-MASS AIR FLOW SENSOR PLAUSIBILITY SIGNAL RATIO ERROR . . . . . . . .19 P2633-MAF SENSOR SIGNAL PLAUSIBILITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 P0105-INTAKE PRESSURE SENSOR CAN MESSAGE ERROR . . . . . . . . . . . . . . . . .25 P0105-INTAKE PRESSURE SENSOR PLAUSIBILITY . . . . . . . . . . . . . . . . . . . . . . . . . .25 P0105-INTAKE PRESSURE SENSOR SIGNAL VOLTAGE TOO HIGH. . . . . . . . . . . . .28 P0105-INTAKE PRESSURE SENSOR SIGNAL VOLTAGE TOO LOW . . . . . . . . . . . . .31 P0110-INTAKE AIR TEMP SENSOR SIGNAL VOLTAGE TOO HIGH . . . . . . . . . . . . . .34 P2063-INTAKE AIR TEMP SENSOR CIRCUIT SIGNAL VOLTAGE TOO HIGH . . . . . .34 P0110-INTAKE AIR TEMP SENSOR SIGNAL VOLTAGE TOO LOW. . . . . . . . . . . . . . .37 P2063-INTAKE AIR TEMP SENSOR CIRCUIT SIGNAL VOLTAGE TOO LOW . . . . . .37 P0115-ENGINE COOLANT TEMP SENSOR CIRCUIT PLAUSIBILITY . . . . . . . . . . . . .40 P2012-ENGINE COOLANT TEMP SENSOR CIRCUIT PLAUSIBILITY . . . . . . . . . . . . .40 P0115-ENGINE COOLANT TEMP SENSOR CIRCUIT PLAUSIBILITY WITH ENGINE OIL SENSOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 P0115-ENGINE COOLANT TEMP SENSOR CIRCUIT SIGNAL VOLTAGE TOO HIGH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44 P2054-ENGINE COOLANT TEMP SENSOR CIRCUIT SIGNAL VOLTAGE TOO HIGH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44 P2054-ENGINE COOLANT TEMP SENSOR CIRCUIT SIGNAL VOLTAGE TOO LOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44 P0115-ENGINE COOLANT TEMP SENSOR CIRCUIT SIGNAL VOLTAGE TOO LOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47 P0180-FUEL TEMPERATURE SENSOR CIRCUIT - SIGNAL VOLTAGE TOO HIGH. .49 P0180-FUEL TEMPERATURE SENSOR CIRCUIT - SIGNAL VOLTAGE TOO LOW . .51 P2625-FUEL TEMPERATURE SENSOR PLAUSIBILITY . . . . . . . . . . . . . . . . . . . . . . . .51 P0190-FUEL PRESS SENSOR CIRCUIT MALF SIGNAL VOLTAGE TOO HIGH . . . . .53 P2008-FUEL PRESSURE SENSOR CIRCUIT SIGNAL VOLTAGE TOO HIGH . . . . . .53 P0190-FUEL PRESS SENSOR CIRCUIT MALF SIGNAL VOLTAGE TOO LOW . . . . .57 P2008-FUEL PRESSURE SENSOR CIRCUIT SIGNAL VOLTAGE TOO LOW . . . . . . .57 P0201-CYLINDER 1-INJECTOR CIRCUIT EXCESSIVE CURRENT . . . . . . . . . . . . . . .60 P0201-CYLINDER 1-INJECTOR CIRCUIT OPEN OR SHORTED TO GROUND . . . . .60 P0201-CYLINDER 1-INJECTOR CIRCUIT SHORTED TO GROUND . . . . . . . . . . . . . .60 P0201-CYLINDER 1-INJECTOR CIRCUIT SHORTED TO VOLTAGE . . . . . . . . . . . . . .60 P0202-CYLINDER 2-INJECTOR CIRCUIT EXCESSIVE CURRENT . . . . . . . . . . . . . . .60 P0202-CYLINDER 2-INJECTOR CIRCUIT OPEN OR SHORTED TO GROUND . . . . .60 P0202-CYLINDER 2-INJECTOR CIRCUIT SHORTED TO GROUND . . . . . . . . . . . . . .60 P0202-CYLINDER 2-INJECTOR CIRCUIT SHORTED TO VOLTAGE . . . . . . . . . . . . . .60 P0203-CYLINDER 3-INJECTOR CIRCUIT EXCESSIVE CURRENT . . . . . . . . . . . . . . .60 P0203-CYLINDER 3-INJECTOR CIRCUIT OPEN OR SHORTED TO GROUND . . . . .60 P0203-CYLINDER 3-INJECTOR CIRCUIT SHORTED TO GROUND . . . . . . . . . . . . . .60 P0203-CYLINDER 3-INJECTOR CIRCUIT SHORTED TO VOLTAGE . . . . . . . . . . . . . .60 P0204-CYLINDER 4-INJECTOR CIRCUIT EXCESSIVE CURRENT . . . . . . . . . . . . . . .60 P0204-CYLINDER 4-INJECTOR CIRCUIT OPEN OR SHORTED TO GROUND . . . . .60
iii

P0204-CYLINDER 4-INJECTOR CIRCUIT SHORTED TO GROUND . . . . . . . . . . . . . .60 P0204-CYLINDER 4-INJECTOR CIRCUIT SHORTED TO VOLTAGE . . . . . . . . . . . . . .60 P0205-CYLINDER 5-INJECTOR CIRCUIT EXCESSIVE CURRENT . . . . . . . . . . . . . . .60 P0205-CYLINDER 5-INJECTOR CIRCUIT OPEN OR SHORTED TO GROUND . . . . .60 P0205-CYLINDER 5-INJECTOR CIRCUIT SHORTED TO GROUND . . . . . . . . . . . . . .60 P0205-CYLINDER 5-INJECTOR CIRCUIT SHORTED TO VOLTAGE . . . . . . . . . . . . . .60 P2123-INJECTOR CIRCUIT FAULT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 P2123-INJECTOR CIRCUIT LOW SIDE SHORTED TO GROUND . . . . . . . . . . . . . . . .60 P2123-INJECTOR CIRCUIT SHORTED TO GROUND OR VOLTAGE . . . . . . . . . . . . .60 P2124-INJECTOR CIRCUIT FAULT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 P2124-INJECTOR CIRCUIT LOW SIDE SHORTED TO GROUND . . . . . . . . . . . . . . . .60 P2124-INJECTOR CIRCUIT SHORTED TO GROUND OR VOLTAGE . . . . . . . . . . . . .60 P2141-CYLINDER #1 INJECTOR OPEN CIRCUIT. . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 P2142-CYLINDER #2 INJECTOR OPEN CIRCUIT. . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 P2143-CYLINDER #3 INJECTOR OPEN CIRCUIT. . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 P2144-CYLINDER #4 INJECTOR OPEN CIRCUIT. . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 P2145-CYLINDER #5 INJECTOR OPEN CIRCUIT. . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 P0300-MISFIRE DETECTED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 P2113-MISFIRE CYLINDER #1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 P2114-MISFIRE CYLINDER #2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 P2115-MISFIRE CYLINDER #3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 P2116-MISFIRE CYLINDER #4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 P2117-MISFIRE CYLINDER #5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 P2567-LEAKAGE CYLINDER #1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 P2567-MISFIRE CYLINDER #1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 P2568-LEAKAGE CYLINDER #2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 P2568-MISFIRE CYLINDER #2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 P2569-LEAKAGE CYLINDER #3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 P2569-MISFIRE CYLINDER #3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 P2570-LEAKAGE CYLINDER #4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 P2570-MISFIRE CYLINDER #4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 P2571-LEAKAGE CYLINDER #5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 P2571-MISFIRE CYLINDER #5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 P2573-GENERAL LEAKAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 P2574-INJECTOR 1 INJECTION TIME ABOVE LIMIT . . . . . . . . . . . . . . . . . . . . . . . . . .66 P2574-INJECTOR 1 INJECTION TIME BELOW LIMIT. . . . . . . . . . . . . . . . . . . . . . . . . .66 P2575-INJECTOR 2 INJECTION TIME ABOVE LIMIT . . . . . . . . . . . . . . . . . . . . . . . . . .66 P2575-INJECTOR 2 INJECTION TIME BELOW LIMIT. . . . . . . . . . . . . . . . . . . . . . . . . .66 P2576-INJECTOR 3 INJECTION TIME ABOVE LIMIT . . . . . . . . . . . . . . . . . . . . . . . . . .66 P2576-INJECTOR 3 INJECTION TIME BELOW LIMIT. . . . . . . . . . . . . . . . . . . . . . . . . .66 P2577-INJECTOR 4 INJECTION TIME ABOVE LIMIT . . . . . . . . . . . . . . . . . . . . . . . . . .66 P2577-INJECTOR 4 INJECTION TIME BELOW LIMIT. . . . . . . . . . . . . . . . . . . . . . . . . .66 P2578-INJECTOR 5 INJECTION TIME ABOVE LIMIT . . . . . . . . . . . . . . . . . . . . . . . . . .66 P2578-INJECTOR 5 INJECTION TIME BELOW LIMIT. . . . . . . . . . . . . . . . . . . . . . . . . .66 P0500-WHEEL SPEED SENSOR PLAUS - CAN BUS MESSAGE FROM ABS . . . . . .69 P0600-CAN DATA BUS - BUS CIRCUIT FAULT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71 P1222-ACC PEDAL POSITION SENSOR 1 CKT PLAUSIBILITY . . . . . . . . . . . . . . . . .73 P1222-ACC PEDAL POSITION SENSOR 1 CKT SIGNAL VOLTAGE TOO HIGH . . . .73 P1222-ACC PEDAL POSITION SENSOR 1 CKT SIGNAL VOLTAGE TOO LOW . . . .73 P1234-ACC PEDAL POSITION SENSOR 2 CIRCUIT PLAUSIBILITY. . . . . . . . . . . . . .73 P1234-ACC PEDAL POSITION SENSOR 2 CKT SIGNAL VOLTAGE TOO HIGH . . . .73 P1234-ACC PEDAL POSITION SENSOR 2 CKT SIGNAL VOLTAGE TOO LOW . . . .73 P2327-APP SENSOR PLAUSIBILITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
iv

P1480-GLOW PLUG INDICATOR ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79 P1482-GLOW PLUG MODULE - COMMUNICATION ERROR. . . . . . . . . . . . . . . . . . . .80 P2537-GLOW PLUG CONTROL CIRCUIT PREGLOW FAULT . . . . . . . . . . . . . . . . . . .80 P2537-GLOW PLUG CONTROL CIRCUIT PREGLOW SHORT TO GROUND. . . . . . .80 P2537-GLOW PLUG CONTROL CIRCUIT PREGLOW SHORT TO VOLTAGE . . . . . .80 P1482-GLOW PLUG MODULE - EXCESS CURRENT. . . . . . . . . . . . . . . . . . . . . . . . . .82 P2133-GLOW PLUG #1 CIRCUIT EXCESSIVE CURRENT. . . . . . . . . . . . . . . . . . . . . .82 P2133-GLOW PLUG #1 CIRCUIT OPEN CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . . . . .82 P2133-GLOW PLUG #1 CIRCUIT SHORT TO GROUND . . . . . . . . . . . . . . . . . . . . . . .82 P2133-GLOW PLUG #1 CIRCUIT SHORT TO VOLTAGE . . . . . . . . . . . . . . . . . . . . . . .82 P2134-GLOW PLUG #2 CIRCUIT EXCESSIVE CURRENT. . . . . . . . . . . . . . . . . . . . . .82 P2134-GLOW PLUG #2 CIRCUIT OPEN CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . . . . .82 P2134-GLOW PLUG #2 CIRCUIT SHORT TO GROUND . . . . . . . . . . . . . . . . . . . . . . .82 P2134-GLOW PLUG #2 CIRCUIT SHORT TO VOLTAGE . . . . . . . . . . . . . . . . . . . . . . .82 P2135-GLOW PLUG #3 CIRCUIT EXCESSIVE CURRENT. . . . . . . . . . . . . . . . . . . . . .82 P2135-GLOW PLUG #3 CIRCUIT OPEN CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . . . . .82 P2135-GLOW PLUG #3 CIRCUIT SHORT TO GROUND . . . . . . . . . . . . . . . . . . . . . . .82 P2135-GLOW PLUG #3 CIRCUIT SHORT TO VOLTAGE . . . . . . . . . . . . . . . . . . . . . . .82 P2136-GLOW PLUG #4 CIRCUIT EXCESSIVE CURRENT. . . . . . . . . . . . . . . . . . . . . .82 P2136-GLOW PLUG #4 CIRCUIT OPEN CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . . . . .82 P2136-GLOW PLUG #4 CIRCUIT SHORT TO GROUND . . . . . . . . . . . . . . . . . . . . . . .82 P2136-GLOW PLUG #4 CIRCUIT SHORT TO VOLTAGE . . . . . . . . . . . . . . . . . . . . . . .82 P2137-GLOW PLUG #5 CIRCUIT EXCESSIVE CURRENT. . . . . . . . . . . . . . . . . . . . . .82 P2137-GLOW PLUG #5 CIRCUIT OPEN CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . . . . .82 P2137-GLOW PLUG #5 CIRCUIT SHORT TO GROUND . . . . . . . . . . . . . . . . . . . . . . .82 P2137-GLOW PLUG #5 CIRCUIT SHORT TO VOLTAGE . . . . . . . . . . . . . . . . . . . . . . .82 P1482-GLOW PLUG MODULE - INCORRECT TIMER . . . . . . . . . . . . . . . . . . . . . . . . .85 P1482-GLOW PLUG MODULE - INTERNAL FAULT . . . . . . . . . . . . . . . . . . . . . . . . . . .85 P2538-GLOW PLUG MODULE COMMUNICATION ERROR . . . . . . . . . . . . . . . . . . . . .85 P2538-GLOW PLUG MODULE EXCESSIVE CURRENT ERROR. . . . . . . . . . . . . . . . .85 P2538-GLOW PLUG MODULE TIMER ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85 P1610-ENGINE CONTROL RELAY PLAUSIBILITY . . . . . . . . . . . . . . . . . . . . . . . . . . . .87 P1610-ENGINE CONTROL RELAY SHUTS OFF TOO EARLY . . . . . . . . . . . . . . . . . . .89 P1610-ENGINE CONTROL RELAY SHUTS OFF TOO LATE . . . . . . . . . . . . . . . . . . . .91 P1611-SENSOR SUPPLY 1 VOLTAGE IS TOO HIGH . . . . . . . . . . . . . . . . . . . . . . . . . .94 P1611-SENSOR SUPPLY 1 VOLTAGE IS TOO LOW . . . . . . . . . . . . . . . . . . . . . . . . . .96 P1612-IGNITION VOLTAGE - VOLTAGE ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99 P1615-ECM VOLTAGE SUPPLY IS TOO HIGH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100 P1615-ECM VOLTAGE SUPPLY IS TOO LOW. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100 P1630-IMMOBILIZER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102 P1630-IMMOBILIZER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102 P1630-IMMOBILIZER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102 P1630-IMMOBILIZER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102 P2201-IMMOBILIZER CAN MESSAGE ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102 P2243-NO MESSAGE RECEIVED FROM SKREEM . . . . . . . . . . . . . . . . . . . . . . . . . .102 P1681-ACM CIRCUIT FAULT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104 P1681-ACM CIRCUIT SHORT TO VOLTAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104 P2009-WATER IN FUEL SENSOR - WATER IN FUEL. . . . . . . . . . . . . . . . . . . . . . . . .106 P2009-WATER IN FUEL SENSOR SIGNAL ERROR . . . . . . . . . . . . . . . . . . . . . . . . . .106 P2010-MASS AIR FLOW SENSOR NEGATIVE DEVIATION . . . . . . . . . . . . . . . . . . . .110 P2010-MASS AIR FLOW SENSOR POSITIVE DEVIATION . . . . . . . . . . . . . . . . . . . . .110 P2068-MASS AIR FLOW SENSOR PLAUSIBILITY SIGNAL RATIO TOO LARGE . . .110 P2068-MASS AIR FLOW SENSOR PLAUSIBILITY SIGNAL RATIO TOO SMALL . . .110
v

P2013-AMBIENT AIR TEMPERATURE SIGNAL VOLTAGE TOO HIGH . . . . . . . . . . .112 P2013-AMBIENT AIR TEMPERATURE SIGNAL VOLTAGE TOO LOW. . . . . . . . . . . .112 P2014-ENGINE OIL SENSOR OIL TEMPERATURE PLAUSIBILITY . . . . . . . . . . . . . .113 P2014-ENGINE OIL SENSOR SIGNAL PLAUSIBILITY . . . . . . . . . . . . . . . . . . . . . . . .113 P2014-ENGINE OIL SENSOR SIGNAL VOLTAGE IS TOO HIGH . . . . . . . . . . . . . . . .113 P2014-ENGINE OIL SENSOR SIGNAL VOLTAGE IS TOO LOW . . . . . . . . . . . . . . . .113 P2040-ENGINE OIL SENSOR CIRCUIT INVALID LEVEL . . . . . . . . . . . . . . . . . . . . . .113 P2040-ENGINE OIL SENSOR CIRCUIT LEVEL OUT OF RANGE . . . . . . . . . . . . . . .113 P2040-ENGINE OIL SENSOR CIRCUIT LEVEL OUT OF RANGE . . . . . . . . . . . . . . .113 P2041-ENGINE OIL SENSOR POOR OIL QUALITY . . . . . . . . . . . . . . . . . . . . . . . . . .113 P2041-ENGINE OIL SENSOR QUALITY MEASUREMENT ERROR . . . . . . . . . . . . . .113 P2041-ENGINE OIL SENSOR QUALITY PLAUSIBILITY . . . . . . . . . . . . . . . . . . . . . . .113 P2042-ENGINE OIL SENSOR WATER CONTAMINATION. . . . . . . . . . . . . . . . . . . . . .113 P2061-ENGINE OIL SENSOR OPEN CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113 P2062-ENGINE OIL SENSOR SIGNAL ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113 P2062-ENGINE OIL SENSOR SYNCHRONIZATION ERROR . . . . . . . . . . . . . . . . . . .113 P2015-FUEL RAIL PRESSURE MALFUNCTION MAXIMUM FUEL FLOW EXCEEDED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .117 P2016-FUEL RAIL PRESSURE MALFUNCTION DECELERATION ERROR . . . . . . .117 P2016-FUEL RAIL PRESSURE MALFUNCTION FUEL FLOW BELOW MINIMUM QUANTITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .117 P2017-FUEL RAIL PRESSURE MALFUNCTION RAIL PRESSURE IS TOO LOW . .117 P2018-FUEL RAIL PRESSURE MALFUNCTION RAIL PRESSURE IS TOO HIGH . .117 P2019-FUEL RAIL PRESSURE MALFUNCTION MAXIMUM FUEL PRESSURE EXCEEDED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .117 P2019-FUEL RAIL PRESSURE MALFUNCTION RAIL PRESSURE IS TOO LOW . .117 P2020-FUEL RAIL PRESSURE MALFUNCTION RAIL PRESSURE IS TOO LOW . .117 P2020-FUEL RAIL PRESSURE MALFUNCTION RAIL PRESSURE TOO HIGH . . . .117 P2021-FUEL RAIL PRESSURE MALFUNCTION RAIL PRESSURE TOO LOW . . . . .117 P2023-FUEL RAIL PRESSURE MALFUNCTION RAIL PRESSURE TOO HIGH . . . .117 P2047-FUEL RAIL PRESSURE MALFUNCTION MAXIMUM FUEL PRESSURE EXCEEDED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .117 P2049-FUEL RAIL PRESSURE MALFUNCTION DECELERATION ERROR . . . . . . .117 P2051-FUEL RAIL PRESSURE MALFUNCTION MAXIMUM FUEL PRESSURE EXCEEDED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .117 P2052-FUEL RAIL PRESSURE MALFUNCTION PLAUSIBILITY WITH FUEL PRESSURE SOLENOID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .117 P2025-INTAKE PRESSURE SENSOR PLAUSIBILITY . . . . . . . . . . . . . . . . . . . . . . . . .125 P2025-INTAKE PRESSURE SENSOR SIGNAL VOLTAGE TOO HIGH. . . . . . . . . . . .128 P2030-INTAKE PRESSURE SENSOR CIRCUIT FAULT . . . . . . . . . . . . . . . . . . . . . . .128 P2030-INTAKE PRESSURE SENSOR OPEN CIRCUIT. . . . . . . . . . . . . . . . . . . . . . . .128 P2030-INTAKE PRESSURE SENSOR SIGNAL VOLTAGE TOO HIGH. . . . . . . . . . . .128 P2025-INTAKE PRESSURE SENSOR SIGNAL VOLTAGE TOO LOW . . . . . . . . . . . .131 P2030-INTAKE PRESSURE SENSOR SIGNAL VOLTAGE TOO LOW . . . . . . . . . . . .131 P2026-O2 SENSOR CIRCUIT FAULT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134 P2026-O2 SENSOR CIRCUIT OPEN CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134 P2026-O2 SENSOR CIRCUIT SIGNAL VOLTAGE TOO HIGH . . . . . . . . . . . . . . . . . .134 P2026-O2 SENSOR CIRCUIT SIGNAL VOLTAGE TOO LOW. . . . . . . . . . . . . . . . . . .134 P2028-O2 SENSOR CIRCUIT FAULT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134 P2028-O2 SENSOR CIRCUIT OPEN CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134 P2028-O2 SENSOR CIRCUIT SIGNAL VOLTAGE TOO HIGH . . . . . . . . . . . . . . . . . .134 P2028-O2 SENSOR CIRCUIT SIGNAL VOLTAGE TOO LOW. . . . . . . . . . . . . . . . . . .134 P2032-O2 SENSOR PLAUSIBILITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134
vi

P2032-O2 SENSOR PLAUSIBILITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134 P2032-O2 SENSOR PLAUSIBILITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134 P2057-O2 SENSOR SIGNAL CIRCUIT SIGNAL VOLTAGE TOO HIGH . . . . . . . . . . .134 P2058-O2 SENSOR SIGNAL CIRCUIT SIGNAL VOLTAGE TOO HIGH . . . . . . . . . . .134 P2059-O2 SENSOR SIGNAL CIRCUIT SIGNAL VOLTAGE TOO HIGH . . . . . . . . . . .134 P2090-O2 SENSOR PLAUSIBILITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134 P2090-O2 SENSOR SIGNAL FAULT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134 P2091-O2 SENSOR LOW O2 CONCENTRATION . . . . . . . . . . . . . . . . . . . . . . . . . . . .134 P2091-O2 SENSOR SIGNAL PLAUSIBILITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134 P2195-O2 SENSOR HEATER CIRCUIT FAULT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134 P2353-O2 SENSOR PLAUSIBILITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134 P2366-O2 CIRCUIT FAULT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134 P2034-O2 SENSOR CIRCUIT CALIBRATION VALUE TOO HIGH . . . . . . . . . . . . . . .138 P2034-O2 SENSOR CIRCUIT CALIBRATION VALUE TOO LOW . . . . . . . . . . . . . . . .138 P2036-O2 SENSOR CIRCUIT CALIBRATION VALUE TOO HIGH . . . . . . . . . . . . . . .138 P2036-O2 SENSOR CIRCUIT CALIBRATION VALUE TOO LOW . . . . . . . . . . . . . . . .138 P2038-O2 SENSOR CIRCUIT CALIBRATION VALUE TOO HIGH . . . . . . . . . . . . . . .138 P2038-O2 SENSOR CIRCUIT CALIBRATION VALUE TOO LOW . . . . . . . . . . . . . . . .138 P2043-CAMSHAFT POSITION SENSOR CIRCUIT OPEN CIRCUIT . . . . . . . . . . . . .140 P2043-CAMSHAFT POSITION SENSOR CIRCUIT OPEN OR SHORT CIRCUIT . . .140 P2045-CRANKSHAFT POSITION SENSOR CIRCUIT LOST SIGNAL . . . . . . . . . . . .146 P2045-CRANKSHAFT POSITION SENSOR CIRCUIT SIGNAL PLAUSIBILITY . . . . .146 P2322-CRANKSHAFT POSITION SENSOR PLAUSIBILITY . . . . . . . . . . . . . . . . . . . .146 P2343-CKP PLAUSIBILITY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .146 P2062-ENGINE OIL SENSOR MONITORING ERROR . . . . . . . . . . . . . . . . . . . . . . . .149 P2066-MASS AIR FLOW SENSOR PLAUSIBILITY . . . . . . . . . . . . . . . . . . . . . . . . . . .150 P2355-EGR FLOW RATE IS TOO HIGH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .150 P2355-EGR FLOW RATE IS TOO LOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .150 P2066-MASS AIR FLOW SENSOR PLAUSIBILITY AIR MASS TOO HIGH . . . . . . . .153 P2066-MASS AIR FLOW SENSOR PLAUSIBILITY AIR MASS TOO LOW. . . . . . . . .153 P2087-INTAKE PRESSURE SENSOR INTAKE RESTRICTION . . . . . . . . . . . . . . . . .156 P2100-FUEL PUMP RELAY CIRCUIT OPEN CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . .157 P2100-FUEL PUMP RELAY CIRCUIT SHORTED TO GROUND . . . . . . . . . . . . . . . . .157 P2100-FUEL PUMP RELAY CIRCUIT SHORTED TO VOLTAGE . . . . . . . . . . . . . . . .159 P2100-FUEL PUMP RELAY EXCESSIVE CURRENT. . . . . . . . . . . . . . . . . . . . . . . . . .159 P2104-STARTER RELAY CIRCUIT SHORT CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . . .161 P2152-STARTER RELAY CIRCUIT SHORT TO GROUND . . . . . . . . . . . . . . . . . . . . .161 P2153-STARTER RELAY CIRCUIT OPEN OR SHORTED TO VOLTAGE . . . . . . . . .161 P2110-BOOST PRESSURE SERVO MOTOR CIRCUIT SHORT CIRCUIT. . . . . . . . .164 P2112-BOOST PRESSURE SERVO MOTOR CIRCUIT EXCESSIVE CURRENT . . .164 P2526-BOOST PRESSURE SERVO MOTOR SHORT TO VOLTAGE. . . . . . . . . . . . .164 P2111-BOOST PRESSURE SERVO MOTOR CIRCUIT SHORT TO GROUND . . . . .167 P2112-BOOST PRESSURE SERVO MOTOR CIRCUIT OPEN CIRCUIT . . . . . . . . . .167 P2510-BOOST PRESSURE SERVO MOTOR SHORT TO GROUND . . . . . . . . . . . . .167 P2526-BOOST PRESSURE SERVO MOTOR OPEN CIRCUIT . . . . . . . . . . . . . . . . . .167 P2526-BOOST PRESSURE SERVO MOTOR SHORT TO GROUND . . . . . . . . . . . . .167 P2132-GLOW PLUG CONTROL MODULE CIRCUIT OPEN CIRCUIT . . . . . . . . . . . .171 P2132-GLOW PLUG CONTROL MODULE CIRCUIT SHORTED TO GROUND . . . .171 P2132-GLOW PLUG CONTROL MODULE CIRCUIT SHORTED TO VOLTAGE OR OPEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .171 P2132-GLOW PLUG CONTROL MODULE FAULT . . . . . . . . . . . . . . . . . . . . . . . . . . . .171 P2151-FUEL PRESS SOLENOID SIGNAL PLAUSIBILITY HIGH . . . . . . . . . . . . . . . .173 P2151-FUEL PRESS SOLENOID SIGNAL PLAUSIBILITY LOW . . . . . . . . . . . . . . . . .173
vii

P2500-FUEL PRESSURE SOLENOID CIRCUIT OPEN CIRCUIT . . . . . . . . . . . . . . . .173 P2501-FUEL PRESSURE SOLENOID CIRCUIT SHORTED TO GROUND OR B+ . .173 P2197-FUEL QUANTITY SOLENOID OPEN CIRCUIT. . . . . . . . . . . . . . . . . . . . . . . . .177 P2198-FUEL QUANTITY SOLENOID SHORT TO VOLTAGE . . . . . . . . . . . . . . . . . . .177 P2199-FUEL QUANTITY SOLENOID SHORT TO GROUND. . . . . . . . . . . . . . . . . . . .177 P2502-FUEL QUANTITY SOLENOID SHORT TO GROUND. . . . . . . . . . . . . . . . . . . .177 P2203-TORQUE REDUCTION MESSAGE FROM ABS - CAN PLAUSIBILITY . . . . .180 P2203-TORQUE REDUCTION MESSAGE FROM ABS - MESSAGE ERROR . . . . . .180 P2203-TORQUE REDUCTION MESSAGE FROM ABS - MESSAGES MISSING . . .180 P2203-TORQUE REDUCTION MESSAGE FROM ABS - NO COMMUNIOCATION .180 P2203-TORQUE REDUCTION MESSAGE FROM ABS - PLAUSIBILITY #1 . . . . . . .180 P2203-TORQUE REDUCTION MESSAGE FROM ABS PLAUSIBILITY #2. . . . . . . . .180 P2208-ABS BRAKE SIGNAL CAN MESSAGE IMPLAUSIBLE . . . . . . . . . . . . . . . . . .180 P2208-ABS CAN BRAKE SIGNAL PLAUSIBILITY . . . . . . . . . . . . . . . . . . . . . . . . . . . .180 P2209-ABS CAN MESSAGE MISSING OR INCORRECT . . . . . . . . . . . . . . . . . . . . . .180 P2253-STEERING ANGLE SENSOR PLAUSIBILITY . . . . . . . . . . . . . . . . . . . . . . . . . .180 P2204-TORQUE REDUCTION MESSAGE FROM TCM - CAN PLAUSIBILITY . . . . .182 P2204-TORQUE REDUCTION MESSAGE FROM TCM - ENGINE STOP . . . . . . . . .182 P2204-TORQUE REDUCTION MESSAGE FROM TCM - MESSAGE ERROR . . . . .182 P2204-TORQUE REDUCTION MESSAGE FROM TCM - MESSAGES MISSING . . .182 P2204-TORQUE REDUCTION MESSAGE FROM TCM - PLAUSIBILITY. . . . . . . . . .182 P2204-TORQUE REDUCTION MESSAGE FROM TCM - TCM DTC #1. . . . . . . . . . .182 P2204-TORQUE REDUCTION MESSAGE FROM TCM - TCM DTC #2. . . . . . . . . . .182 P2210-ESM CAN MESSAGE MISSING OR INCORRECT. . . . . . . . . . . . . . . . . . . . . .184 P2234-ABS DTC EXTERNAL QUANTITY CONTROL FAULT PRESENT . . . . . . . . . .184 P2252-LATERAL ACCELERATOR SENSOR PLAUSIBILTY. . . . . . . . . . . . . . . . . . . . .184 P2211-ETC CAN MESSAGE MISSING OR INCORRECT . . . . . . . . . . . . . . . . . . . . . .186 P2258-TCM MESSAGE ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .186 P2258-TCM NO CAN MESSAGE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .186 P2217-TCM DTC INTERNAL FAULT PRESENT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .188 P2218-TCM DTC 1-2 AND 4-5 SHIFT SOLENOID FAULT PRESENT . . . . . . . . . . . .188 P2219-TCM DTC 2-3 SHIFT SOLENOID FAULT PRESENT . . . . . . . . . . . . . . . . . . . .188 P2220-TCM DTC 3-4 SHIFT SOLENOID FAULT PRESENT . . . . . . . . . . . . . . . . . . . .188 P2221-TCM DTC TORQUE CONVERTER CLUTCH SOLENOID FAULT PRESENT.188 P2222-TCM DTC MODULATING PRESSURE SOLENOID FAULT PRESENT . . . . . .188 P2223-TCM DTC SHIFT PRESSURE SOLENOID FAULT PRESENT. . . . . . . . . . . . .188 P2224-TCM DTC VALVE VOLTAGE SUPPLY FAULT PRESENT . . . . . . . . . . . . . . . .188 P2225-TCM DTC SPEED SENSOR VOLTAGE FAULT PRESENT . . . . . . . . . . . . . . .188 P2226-TCM DTC EWM CAN MESSAGE FAULT PRESENT . . . . . . . . . . . . . . . . . . . .188 P2227-TCM DTC RIGHT REAR WHEEL SPEED IMPLAUSIBLE FAULT PRESENT .188 P2228-TCM DTC TRANSMISSION RATIO ERROR FAULT PRESENT . . . . . . . . . . .188 P2229-TCM DTC CAN MSG IMPLAUSIBLE FAULT PRESENT . . . . . . . . . . . . . . . . .188 P2230-TCM DTC TCC EXCESSIVE POWER CONSUMPTION FAULT PRESENT . .188 P2231-TCM DTC NOT UNEQUIVOCAL FAULT PRESENT . . . . . . . . . . . . . . . . . . . . .188 P2232-TCM DTC NEGATIVE GEAR COMPARISON FAULT PRESENT . . . . . . . . . . .188 P2240-ABS STEERING ANGLE SENSOR CAN MESSAGE IMPLAUSIBLE 1 . . . . . .190 P2240-ABS STEERING ANGLE SENSOR CAN MESSAGE IMPLAUSIBLE 2 . . . . . .190 P2242-ABS BRAKE MESSAGE PLAUSIBILITY 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . .192 P2242-ABS BRAKE MESSAGE PLAUSIBILITY 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . .192 P2244-INSTRUMENT CLUSTER MESSAGE PLAUSIBILITY . . . . . . . . . . . . . . . . . . .194 P2259-TORQUE REDUCTION MESSAGE FROM HVAC- PARITY ERROR. . . . . . . .196 P2259-TORQUE REDUCTION MESSAGE FROM HVAC- SWITCH SIGNAL ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .196
viii

P2259-TORQUE REDUCTION MESSAGE FROM HVAC- SWITCH SIGNAL PLAUSIBILITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .196 P229-INSTRUMENT CLUSTER MESSAGE - AMBIENT TEMPERATURE SIGNAL PLAUSIBILITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .197 P2306-SENSOR SUPPLY 2 VOLTAGE IS TOO HIGH . . . . . . . . . . . . . . . . . . . . . . . . .198 P2306-SENSOR SUPPLY 2 VOLTAGE IS TOO LOW . . . . . . . . . . . . . . . . . . . . . . . . .200 P2332-SENSOR SUPPLY 3 VOLTAGE IS TOO LOW . . . . . . . . . . . . . . . . . . . . . . . . .203 P2332-SENSOR SUPPLY 3 VOLTAGE IS TOO HIGH . . . . . . . . . . . . . . . . . . . . . . . . .206 P2333-S/C VEHICLE SPEED PLAUSIBILITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .209 P2338-S/C EXCESSIVE ACCELERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .209 P2338-S/C EXCESSIVE DECELERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .209 P2339-ECM CHECKSUM ERROR #1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .211 P2339-ECM CHECKSUM ERROR #2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .211 P2339-ECM INVALID CODING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .211 P2339-ECM INVALID DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .211 P2344-KICKDOWN SWITCH PLAUSIBILITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .212 P2347-AUTOMATIC TRANSMISSION CODED AS MANUAL TRANSMISSION . . . . .213 P2347-CAN BUS CIRCUIT INTERUPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .213 P2347-MANUAL TRANSMISSIO CODED AS AUTO TRANSMISSION . . . . . . . . . . . .213 P2347-WRITE ERROR TO EEPROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .213 P2351-ECM SUPPLY VOLTAGE TOO LOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .214 P2359-BOOST PRESSURE TOO HIGH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .216 P2359-BOOST PRESSURE TOO LOW. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .216 P2511-EGR VALVE SIGNAL CIRCUIT SHORTED TO GROUND . . . . . . . . . . . . . . . .218 P2527-EGR VALVE SIGNAL CIRCUIT OPEN CIRCUIT. . . . . . . . . . . . . . . . . . . . . . . .218 P2527-EGR VALVE SIGNAL CIRCUIT SHORTED TO GROUND . . . . . . . . . . . . . . . .218 P2514-CRANKCASE VENT HEATER OPEN CIRCUIT . . . . . . . . . . . . . . . . . . . . . . . .221 P2514-CRANKCASE VENT HEATER SHORTED TO GROUND . . . . . . . . . . . . . . . . .221 P2514-CRANKCASE VENT HEATER SHORTED TO VOLTAGE. . . . . . . . . . . . . . . . .221 P2521-IMPROPER START ATTEMPT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .224 P2527-EGR VALVE SIGNAL CIRCUIT SHORTED TO VOLTAGE . . . . . . . . . . . . . . . .225 P2531-FUEL INJECTOR 1 READ TOO LARGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .227 P2531-FUEL INJECTOR 1 READ TOO LARGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .227 P2531-FUEL INJECTOR 1 READ TOO SMALL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .227 P2531-FUEL INJECTOR 1 READ TOO SMALL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .227 P2532-FUEL INJECTOR 2 READ TOO LARGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .227 P2532-FUEL INJECTOR 2 READ TOO LARGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .227 P2532-FUEL INJECTOR 2 READ TOO SMALL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .227 P2532-FUEL INJECTOR 2 READ TOO SMALL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .227 P2533-FUEL INJECTOR 3 READ TOO LARGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .227 P2533-FUEL INJECTOR 3 READ TOO LARGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .227 P2533-FUEL INJECTOR 3 READ TOO SMALL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .227 P2533-FUEL INJECTOR 3 READ TOO SMALL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .227 P2534-FUEL INJECTOR 4 READ TOO LARGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .227 P2534-FUEL INJECTOR 4 READ TOO LARGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .227 P2534-FUEL INJECTOR 4 READ TOO SMALL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .227 P2534-FUEL INJECTOR 4 READ TOO SMALL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .227 P2535-FUEL INJECTOR 5 READ TOO LARGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .227 P2535-FUEL INJECTOR 5 READ TOO LARGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .227 P2535-FUEL INJECTOR 5 READ TOO SMALL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .227 P2535-FUEL INJECTOR 5 READ TOO SMALL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .227 P2606-CMP/CKP SYNCHRONIZATION ERROR . . . . . . . . . . . . . . . . . . . . . . . . . . . . .229 *CHECKING THE FUEL PRESSURE SENSOR CIRCUITS . . . . . . . . . . . . . . . . . . . . .232
ix

*CHECKING THE FUEL PRESSURE SOLENOID CIRCUITS . . . . . . . . . . . . . . . . . . .233 *CHECKING THE FUEL QUANTITY SOLENOID CIRCUITS . . . . . . . . . . . . . . . . . . . .234 *CHECKING THE POWER AND GROUNDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .235 *ENGINE CRANKS BUT WILL NOT START . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .239 *ENGINE WILL NOT CRANK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .242 VERIFICATION TESTS VERIFICATION TESTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .246 8.0 COMPONENT LOCATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .249 8.1 8.2 8.3 8.4 8.5 9.0 CONTROL MODULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .249 CONTROLS AND SOLENOIDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .249 DATA LINK CONNECTOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .250 SENSORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .251 SWITCHES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .253
CONNECTOR PINOUTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .255 ACCELERATOR PEDAL POSITION SENSOR (OBD) . . . . . . . . . . . . . . . . . . . . . . . . .255 AIRBAG CONTROL MODULE - YELLOW. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .255 BOOST PRESSURE SENSOR (OBD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .255 BOOST PRESSURE SERVOMOTOR (OBD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .256 CAMSHAFT POSITION SENSOR - BLACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .256 CONTROLLER ANTILOCK BRAKE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .257 CRANKCASE HEATER - BLACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .257 CRANKSHAFT POSITION SENSOR - BLACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .258 DATA LINK CONNECTOR - BLACK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .258 EGR VALVE - BLACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .258 ENGINE CONTROL MODULE C1 (OBD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .259 ENGINE CONTROL MODULE C2 (OBD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .260 ENGINE COOLANT TEMPERATURE SENSOR - BLACK . . . . . . . . . . . . . . . . . . . . . .260 ENGINE OIL SENSOR - BLACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .261 FUEL INJECTOR NO. 1 - BLACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .261 FUEL INJECTOR NO. 2 - BLACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .261 FUEL INJECTOR NO. 3 - BLACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .261 FUEL INJECTOR NO. 4 - BLACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .262 FUEL INJECTOR NO. 5 - BLACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .262 FUEL PRESSURE SENSOR - BLACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .262 FUEL PRESSURE SOLENOID. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .262 FUEL PUMP (OBD). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .262 FUEL PUMP RELAY (OBD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .263 FUEL QUANTITY CONTROL VALVE (OBD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .263 FUEL TEMPERATURE SENSOR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .263 ENGINE CONTROL RELAY (FUSE BLOCK NO. 1) . . . . . . . . . . . . . . . . . . . . . . . . . . .265 FUSES (FUSE BLOCK NO. 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .265 FUSES (FUSE BLOCK NO. 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .267 FUSES (FUSE/RELAY BLOCK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .269 STARTER MOTOR RELAY (FUSE/RELAY BLOCK) . . . . . . . . . . . . . . . . . . . . . . . . . . .269 GLOW PLUG CONTROL MODULE C1 - BLACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . .270 GLOW PLUG CONTROL MODULE C2 - BLACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . .270 INTAKE AIR PRESSURE SENSOR (OBD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .270 INTAKE AIR TEMPERATURE SENSOR - BLACK . . . . . . . . . . . . . . . . . . . . . . . . . . . .270

KICK DOWN SWITCH - BLACK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .271 MASS AIR FLOW SENSOR - BLACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .271 OXYGEN SENSOR (OBD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .271 FUSED IGNITION SWITCH RUN-START RELAY (RELAY BLOCK) . . . . . . . . . . . . . .273 SPEED CONTROL SWITCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .273 WATER IN FUEL SENSOR - BLACK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .273 10.0 SCHEMATIC DIAGRAMS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .275 10.1 ENGINE CONTROL MODULE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .275 10.2 ENGINE CONTROL MODULE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .276 11.0 CHARTS AND GRAPHS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .277
xi
NOTES
xii
GENERAL INFORMATION
1.0 INTRODUCTION 2.0 IDENTIFICATION OF SYSTEM
The procedures contained in this manual include all specifications, instructions and graphics needed to diagnose engine control module (ECM) and sentry key remote entry module (SKREEM) problems; they are no start, diagnostic trouble code (DTC) and no trouble code problems for the ECM. The diagnostics in this manual are based on the trouble condition or symptom being present at the time of diagnosis. When repairs are required, refer to the appropriate service information for the proper removal and repair procedure. Diagnostic procedures change every year. New diagnostic systems may be added; carryover systems may be enhanced. IT IS RECOMMENDED THAT YOU REVIEW THE ENTIRE MANUAL TO BECOME FAMILIAR WITH ALL NEW AND CHANGED DIAGNOSTIC PROCEDURES. This manual will cover all the necessary requirements to begin a logical diagnostic path for each problem. If there is a diagnostic trouble code (DTC) detected, go to the trouble code test. If there are no DTCs present, go to a no trouble code (*), symptom based test. This book reflects many suggested changes from readers of past issues. After using this book, if you have any comments or recommendations, please fill out the form at the back of the book and mail it back to us.
The ECM is located to the left of the steering column behind the steering column opening cover. The sentry remote entry module (SKREEM) is attached to the rear of the instrument cluster.
3.0
SYSTEM DESCRIPTION AND FUNCTIONAL OPERATION GENERAL DESCRIPTION
3.1
The 2.7L direct injection diesel engine system is equipped with the latest technical advances. The on-board diagnostics incorporated in the engine control module and SKREEM are intended to assist the field technician in repairing vehicle problems by the quickest means. The engine system incorporates a common rail fuel delivery design with exhaust emission feedback. This design utilizes electronically controlled solenoid valve type fuel injectors. Each injector is controlled individually by the ECM. Injector timing and fuel quantity are controlled by the ECM based on inputs from various sensors. The precision control of the injectors by the ECM helps to reduce the engine noise, odor and smoke.
1.1
SYSTEM COVERAGE
3.2 3.2.1
FUNCTIONAL OPERATION ECM ON-BOARD DIAGNOSTICS
This diagnostic procedures manual covers 2005 Sprinter vehicles equipped with the 2.7L common rail diesel engine.
1.2
SIX-STEP TROUBLESHOOTING PROCEDURE
Diagnosis of the engine control module (ECM) and sentry key immobilizer system (SKREEM) is done in six basic steps: verification of complaint verification of any related symptom symptom analysis problem isolation repair of isolated problem
verification of proper operation
NOTE: All tests in this manual should be performed with the engine at operating temperature, unless otherwise specified within a particular test.
The ECM is programmed to monitor different circuits of the diesel fuel injection system. This monitoring is called on-board diagnostics. Certain criteria must be met for a diagnostic trouble code to be entered into the ECM memory. The criteria may be a range of: engine rpm, engine temperature, time or other input signals to the ECM. If all of the criteria for monitoring a system or circuit are met, and a problem is sensed, then a DTC will be stored in the ECM memory. It is possible that a DTC for a monitored circuit may not be entered into the ECM memory, even though a malfunction has occurred. This may happen when the monitoring criteria have not been met. The ECM compares input signal voltages from each input device with specifications (the established high and low limits of the input range) that are programmed into it for that device. If the input voltage is not within the specifications and other trouble code criteria are met, a DTC will be stored in the ECM memory.
GENERAL INFORMATION
3.2.2 ECM OPERATING MODES
As input signals to the ECM change, the ECM adjusts its response to the output devices. For example, the ECM must calculate a different fuel quantity and fuel timing for engine idle condition than it would for a wide open throttle condition. There are several different modes of operation that determine how the ECM responds to the various input signals. position. Other less critical faults will result in power reduction throughout the full range of driving conditions.
Overspeed Detection Mode

If the ECM detects engine RPM that exceeds 5200 RPM, the ECM will set a DTC in memory, limit engine RPM to no more than 2500 RPM, and illuminate the MIL until the DTC is cleared.
Ignition Switch On (Engine Off)

When the ignition is turned on the ECM activates the glow plug relay for a time period that is determined by engine coolant temperature, intake air temperature and battery voltage.
After-Run Mode
The ECM transfers RAM information to ROM and performs an Input/Output state check.
3.2.3
MONITORED CIRCUITS
Engine Start-Up Mode

The ECM uses the intake air temperature sensor, engine temperature sensor and the crankshaft position sensor (engine speed) inputs to determine fuel injection quantity.
Normal Driving Modes

Engine idle, warm-up, acceleration, deceleration and wide open throttle modes are controlled based on all of the sensor inputs to the ECM. The ECM uses these sensor inputs to adjust fuel quantity and fuel injector timing. EGR valve control is performed using feedback from the oxygen sensor. An oxygen sensor is located in the exhaust manifold to sample oxygen content exiting the engine cylinders. The ECM uses the O2 sensor, along with other sensor inputs, to govern the amount of exhaust gas recirculation to reduce HC (HydroCarbons) and CO (Carbon Monoxide). Engine coolant is routed through the base of the EGR valve to provide additional cooling of the exhaust gas, which further helps the reductions of emissions. The EGR valve has a self-cleaning function. When the engine is shut off, the EGR valve rotates twice to reduce carbon deposits at the valve seat.
The ECM is able to monitor and identify most driveability related trouble conditions. Some circuits are directly monitored through ECM feedback circuitry. In addition, the ECM monitors the voltage state of some circuits and compares those states with expected values. Other systems are monitored indirectly when the ECM conducts a rationality test to identify problems. Although most subsystems of the engine control module are either directly or indirectly monitored, there may be occasions when diagnostic trouble codes are not immediately identified. For a trouble code to set, a specific set of conditions must occur and unless these conditions occur, a DTC will not set.
3.2.4
SKREEM OVERVIEW
Overheat Production Mode

If the engine temperature is above 105C (221F) and vehicle speed is above 40 km/h (25 MPH) the ECM will limit fuel quantity for engine protection.
The sentry key remote entry module system (SKREEM) is designed to prevent unauthorized vehicle operation. The system consists of a sentry key remote entry module (SKREEM), ignition key(s) equipped with a transponder chip and the ECM. When the ignition switch is turned on, the SKREEM interrogates the ignition key. If the ignition key is Valid or Invalid, the SKREEM sends a message to the ECM indicating ignition key status. Upon receiving this message the ECM will terminate engine operation or allow the engine to continue to operate.
3.2.5
SKREEM ON-BOARD DIAGNOSTICS
Limp-In Mode
The ECM utilizes different degrees of engine limp-in. The ECM is able to limit engine rpm, engine power output (turbo boost reduction), activate engine cooling fan or all of these functions based on the type of fault that is detected. Critical engine performance faults such as accelerator pedal position sensor fault will result in a fixed idle speed of approximately 680 rpm regardless of actual pedal
The SKREEM has been programmed to transmit and monitor many different coded messages as well as CAN Bus messages. This monitoring is called On-Board Diagnostics. Certain criteria must be met for a DTC to be entered into SKREEM memory. The criteria may be a range of; input voltage, CAN Bus message or coded messages to the SKREEM. If all the criteria for monitoring a circuit or function are met and a fault is detected, a DTC will be stored in the SKREEM memory and the START ERROR indicator will be turned on in the instrument cluster.
2
GENERAL INFORMATION
3.2.6 SKREEM OPERATION
When ignition power is supplied to the SKREEM, the SKREEM performs an internal self-test. After the self-test is complete, the SKREEM energizes the antenna (this activates the transponder chip) and sends a challenge to the transponder chip. The transponder chip responds to the challenge by generating an encrypted response message. After responding to the coded message, the transponder sends a transponder ID message to the SKREEM. The SKREEM compares the transponder ID message to the available valid key codes in SKREEM memory (8 key maximum at any one time). After validating the ignition key the SKREEM sends a CAN Bus message request to the ECM, then waits for the ECM response. If the ECM does not respond, the SKREEM will send the request again. If the ECM does not respond again, the SKREEM will stop sending the request and store a trouble code in memory. If the ECM sends a correct response to the SKREEM, the SKREEM sends a valid/invalid key message to the ECM. The ECM will allow or disallow engine operation based on this message. Secret Key - an electronically stored value (identification number) that is unique to each SKREEM. The secret key is stored in the SKREEM, ECM and all ignition key transponders. Challenge - a random number that is generated by the SKREEM at each ignition key cycle. The secret key and challenge are the two variables used in the algorithm that produces the encrypted response message. The transponder uses the crypto algorithm to receive, decode and respond to the message sent by the SKREEM. After responding to the coded message, the transponder sends a transponder ID message to the SKREEM. beginning of each test. When the fault is not a hard code, an intermittent test must be performed.
NOTE: If the DRBIII displays faults for multiple components (i.e. ECT, MAF, IAT sensors) identify and check the shared circuits for possible problems before continuing (i.e. sensor grounds or 5-volt supply circuits). Refer to the appropriate schematic to identify shared circuits.
3.3.2
INTERMITTENT CODE
A DTC that is not current every time the ECM/ SKREEM checks the circuit or function is an intermittent code. Most intermittent DTCs are caused by wiring or connector problems. Problems that come and go like this are the most difficult to diagnose; they must be looked for under specific conditions that cause them. The following checks may assist you in identifying a possible intermittent problem. Visually inspect the related wire harness connectors. Look for broken, bent, pushed out or corroded terminals. Visually inspect the related wire harness. Look for chafed, pierced or partially broken wire. Refer to hotlines or technical service bulletins that may apply.
NOTE: Electromagnetic (radio) interference can cause an intermittent system malfunction. This interference can interrupt communication between the ignition key transponder and the SKREEM.
3.3
DIAGNOSTIC TROUBLE CODES
3.3.3
ECM DIAGNOSTIC TROUBLE CODES
Each diagnostic trouble code (DTC) is diagnosed by following a specific procedure. The diagnostic test procedure contains step-by-step instruction for determining the cause of the DTC as well as no trouble code problems. It is not necessary to perform all of the tests in this book to diagnose an individual code. Always begin diagnosis by reading the DTCs using the DRBIII . This will direct you to the specific test(s) that must be performed.
3.3.1
HARD CODE
A DTC that comes back within one cycle of the ignition key is a hard code. This means that the problem is current every time the ECM/SKREEM checks that circuit or function. Procedures in this manual verify if the DTC is a hard code at the
3
IMPORTANT NOTE: Before replacing the ECM for a failed driver, control circuit or ground circuit, be sure to check the related component/circuit integrity for failures not detected due to a double fault in the circuit. Most ECM driver/control circuit failures are caused by internal failures to components (i.e. relays and solenoids) and shorted circuits (i.e. sensor pull-ups, drivers and ground circuits). These faults are difficult to detect when a double fault has occurred and only one DTC has set.
If the DRBIII displays faults for multiple components (i.e. MAF, ECT, ENG OIL, etc.), identify and check the shared circuits for possible problems before continuing (i.e. sensor grounds or 5-volt
GENERAL INFORMATION
supply circuits). Refer to the appropriate wiring diagrams to identify shared circuits. abs brake message plausibility 1 abs brake message plausibility 2 abs brake signal can message implausible abs can brake signal plausibility abs can message missing or incorrect abs dtc external quantity control fault present abs steering angle sensor can message implausible 1 abs steering angle sensor can message implausible 2 acc pedal position sensor 1 ckt plausibility acc pedal position sensor 1 ckt signal voltage too high acc pedal position sensor 1 ckt signal voltage too low acc pedal position sensor 2 circuit plausibility acc pedal position sensor 2 ckt signal voltage too high acc pedal position sensor 2 ckt signal voltage too low acm circuit fault acm circuit short to voltage ambient air temperature signal voltage too high ambient air temperature signal voltage too low app sensor plausibility atmospheric pressure sensor plausibility with boost pressure sensor atmospheric pressure sensor signal voltage too high atmospheric pressure sensor signal voltage too low automatic transmission coded as manual transmission boost pressure servo motor circuit excessive current boost pressure servo motor circuit open circuit boost pressure servo motor circuit short circuit boost pressure servo motor circuit short to ground boost pressure servo motor excessive current boost pressure servo motor open circuit boost pressure servo motor short to ground boost pressure servo motor short to ground boost pressure servo motor short to voltage boost pressure too high boost pressure too low camshaft position sensor circuit open circuit camshaft position sensor circuit open or short circuit can bus circuit interuption can data bus -bus circuit fault can message error *checking the fuel pressure sensor circuits *checking the fuel pressure solenoid circuits *checking the fuel quantity solenoid circuits *checking the power and grounds ckp plausibility cmp/ckp synchronization error crankcase vent heater excessive current crankcase vent heater open circuit crankcase vent heater shorted to ground crankcase vent heater shorted to voltage
4
crankshaft position sensor circuit lost signal crankshaft position sensor circuit signal plausibility crankshaft position sensor plausibility cylinder #1 injector open circuit cylinder #2 injector open circuit cylinder #3 injector open circuit cylinder #4 injector open circuit cylinder #5 injector open circuit cylinder 1-injector circuit excessive current cylinder 1-injector circuit open or shorted to ground cylinder 1-injector circuit shorted to voltage cylinder 1-injector circuit shorted to ground cylinder 2-injector circuit excessive current cylinder 2-injector circuit open or shorted to ground cylinder 2-injector circuit shorted to ground cylinder 2-injector circuit shorted to voltage cylinder 3-injector circuit excessive current cylinder 3-injector circuit open or shorted to ground cylinder 3-injector circuit shorted to ground cylinder 3-injector circuit shorted to voltage cylinder 4-injector circuit excessive current cylinder 4-injector circuit open or shorted to ground cylinder 4-injector circuit shorted to ground cylinder 4-injector circuit shorted to voltage cylinder 5-injector circuit excessive current cylinder 5-injector circuit open or shorted to ground cylinder 5-injector circuit shorted to ground cylinder 5-injector circuit shorted to voltage ecm a/d converter high ecm a/d converter low ecm a/d converter plausibility ecm checksum error #1 ecm checksum error #2 ecm incorrect value ecm injection quantity error ecm injector monitoring 1 ecm injector monitoring 2 ecm injector monitoring 3 ecm injector monitoring 4 ecm injector output stage #1 ecm injector output stage #1 short circuit ecm injector output stage #2 ecm injector output stage #2 short circuit ecm injector undervoltage ecm internal error ecm internal error ecm internal error ecm internal error ecm internal error 1 ecm internal error 1 ecm internal error 1 ecm internal error 1 ecm internal error 1 ecm internal error 2 ecm internal error 2 ecm internal error 2 ecm internal error 3
GENERAL INFORMATION
ecm internal error 3 ecm internal error 4 ecm internal error 4 ecm internal error 5 ecm internal fault ecm invalid coding ecm invalid data ecm read error ecm read/write error ecm supply voltage too low ecm voltage supply is too high ecm voltage supply is too low ecm write error egr flow rate is too high egr flow rate is too low egr valve excessive current egr valve signal circuit open circuit egr valve signal circuit shorted to ground egr valve signal circuit shorted to ground egr valve signal circuit shorted to voltage engine control relay plausibility engine control relay shuts off too early engine control relay shuts off too late engine coolant temp sensor circuit plausibility engine coolant temp sensor circuit plausibility engine coolant temp sensor circuit plausibility with engine oil sensor engine coolant temp sensor circuit signal voltage too high engine coolant temp sensor circuit signal voltage too high engine coolant temp sensor circuit signal voltage too low engine coolant temp sensor circuit signal voltage too low *engine cranks but will not start engine oil sensor circuit invalid level engine oil sensor circuit level out of range engine oil sensor circuit level out of range engine oil sensor monitoring error engine oil sensor oil temperature plausibility engine oil sensor open circuit engine oil sensor poor oil quality engine oil sensor quality measurement error engine oil sensor quality plausibility engine oil sensor signal error engine oil sensor signal plausibility engine oil sensor signal voltage is too high engine oil sensor signal voltage is too low engine oil sensor synchronization error engine oil sensor water contamination *engine will not crank esm can message missing or incorrect etc can message missing or incorrect fuel injector 1 read too large fuel injector 1 read too large fuel injector 1 read too small fuel injector 1 read too small
5
fuel injector 2 read too large fuel injector 2 read too large fuel injector 2 read too small fuel injector 2 read too small fuel injector 3 read too large fuel injector 3 read too large fuel injector 3 read too small fuel injector 3 read too small fuel injector 4 read too large fuel injector 4 read too large fuel injector 4 read too small fuel injector 4 read too small fuel injector 5 read too large fuel injector 5 read too large fuel injector 5 read too small fuel injector 5 read too small fuel press sensor circuit malf signal voltage too high fuel press sensor circuit malf signal voltage too low fuel press solenoid signal plausibility high fuel press solenoid signal plausibility low fuel pressure sensor circuit signal voltage too high fuel pressure sensor circuit signal voltage too low fuel pressure solenoid circuit excessive current fuel pressure solenoid circuit open circuit fuel pressure solenoid circuit shorted to ground or b+ fuel pump relay circuit open circuit fuel pump relay circuit shorted to ground fuel pump relay circuit shorted to voltage fuel pump relay excessive current fuel quantity solenoid ecm thermal overload fuel quantity solenoid open circuit fuel quantity solenoid short to ground fuel quantity solenoid short to ground fuel quantity solenoid short to voltage fuel rail pressure malfunction deceleration error fuel rail pressure malfunction deceleration error fuel rail pressure malfunction fuel flow below minimum quantity fuel rail pressure malfunction maximum fuel flow exceeded fuel rail pressure malfunction maximum fuel pressure exceeded fuel rail pressure malfunction maximum fuel pressure exceeded fuel rail pressure malfunction maximum fuel pressure exceeded fuel rail pressure malfunction plausibility with fuel pressure solenoid fuel rail pressure malfunction rail pressure is too high fuel rail pressure malfunction rail pressure is too low fuel rail pressure malfunction rail pressure is too low fuel rail pressure malfunction rail pressure is too low fuel rail pressure malfunction rail pressure too high
GENERAL INFORMATION
fuel rail pressure malfunction rail pressure too high fuel rail pressure malfunction rail pressure too low fuel temperature sensor circuit signal voltage too high fuel temperature sensor circuit signal voltage too low fuel temperature sensor plausibility general leakage glow plug #1 circuit excessive current glow plug #1 circuit open circuit glow plug #1 circuit short to ground glow plug #1 circuit short to voltage glow plug #2 circuit excessive current glow plug #2 circuit open circuit glow plug #2 circuit short to ground glow plug #2 circuit short to voltage glow plug #3 circuit excessive current glow plug #3 circuit open circuit glow plug #3 circuit short to ground glow plug #3 circuit short to voltage glow plug #4 circuit excessive current glow plug #4 circuit open circuit glow plug #4 circuit short to ground glow plug #4 circuit short to voltage glow plug #5 circuit excessive current glow plug #5 circuit open circuit glow plug #5 circuit short to ground glow plug #5 circuit short to voltage glow plug control circuit preglow fault glow plug control circuit preglow short to ground glow plug control circuit preglow short to voltage glow plug control module circuit open circuit glow plug control module circuit shorted to ground glow plug control module circuit shorted to voltage or open glow plug control module fault glow plug indicator error glow plug module communication error glow plug module -communication error glow plug module -excess current glow plug module excessive current error glow plug module -incorrect timer glow plug module -internal fault glow plug module timer error ignition voltage -voltage error immobilizer immobilizer immobilizer immobilizer immobilizer can message error improper start attempt injection fault excessive engine speed injection fault -excessive temperature injection fault -quantity error injection fault -torque limit injector 1 injection time above limit injector 1 injection time below limit injector 2 injection time above limit
6
injector 2 injection time below limit injector 3 injection time above limit injector 3 injection time below limit injector 4 injection time above limit injector 4 injection time below limit injector 5 injection time above limit injector 5 injection time below limit injector bank error injector bank error injector circuit fault injector circuit fault injector circuit low side shorted to ground injector circuit low side shorted to ground injector circuit shorted to ground or voltage injector circuit shorted to ground or voltage instrument cluster message -ambient temperature signal plausibility instrument cluster message plausibility intake air temp sensor circuit signal voltage too high intake air temp sensor circuit signal voltage too low intake air temp sensor signal voltage too high intake air temp sensor signal voltage too low intake pressure sensor can message error intake pressure sensor circuit fault intake pressure sensor intake restriction intake pressure sensor open circuit intake pressure sensor plausibility intake pressure sensor plausibility intake pressure sensor signal voltage too high intake pressure sensor signal voltage too high intake pressure sensor signal voltage too high intake pressure sensor signal voltage too low intake pressure sensor signal voltage too low intake pressure sensor signal voltage too low internal error counter fault internal error engine shut off internal error engine voltage monitoring internal error engine voltage monitoring internal voltage error kickdown switch plausibility lateral accelerator sensor plausibilty leakage cylinder #1 leakage cylinder #2 leakage cylinder #3 leakage cylinder #4 leakage cylinder #5 maf sensor signal plausibility manual transmissio coded as auto transmission mass air flow sensor negative deviation mass air flow sensor plausibility mass air flow sensor plausibility air mass too high mass air flow sensor plausibility air mass too high mass air flow sensor plausibility air mass too low mass air flow sensor plausibility air mass too low mass air flow sensor plausibility signal ratio error mass air flow sensor plausibility signal ratio too large mass air flow sensor plausibility signal ratio too
GENERAL INFORMATION
small mass air flow sensor positive deviation mass air flow sensor signal circuit open or shorted mass air flow sensor signal voltage too high mass air flow sensor signal voltage too high mass air flow sensor signal voltage too low mass air flow sensor signal voltage too low mass air flow sensor signal voltage too low mass air flow sensor signal voltage too low mass air flow sensor supply voltage too high mass air flow sensor supply voltage too low misfire cylinder #1 misfire cylinder #1 misfire cylinder #2 misfire cylinder #2 misfire cylinder #3 misfire cylinder #3 misfire cylinder #4 misfire cylinder #4 misfire cylinder #5 misfire cylinder #5 misfire detected no message received from skreem o2 circuit fault o2 sensor circuit calibration value too high o2 sensor circuit calibration value too high o2 sensor circuit calibration value too high o2 sensor circuit calibration value too low o2 sensor circuit calibration value too low o2 sensor circuit calibration value too low o2 sensor circuit fault o2 sensor circuit fault o2 sensor circuit open circuit o2 sensor circuit open circuit o2 sensor circuit signal voltage too high o2 sensor circuit signal voltage too high o2 sensor circuit signal voltage too low o2 sensor circuit signal voltage too low o2 sensor heater circuit fault o2 sensor low o2 concentration o2 sensor plausibility o2 sensor plausibility o2 sensor plausibility o2 sensor plausibility o2 sensor plausibility o2 sensor signal circuit signal voltage too high o2 sensor signal circuit signal voltage too high o2 sensor signal circuit signal voltage too high o2 sensor signal fault o2 sensor signal plausibility s/c excessive acceleration s/c excessive deceleration s/c vehicle speed plausibility sensor supply 1 voltage is too high sensor supply 1 voltage is too low sensor supply 2 voltage is too high sensor supply 2 voltage is too low sensor supply 3 voltage is too high
7
sensor supply 3 voltage is too low starter relay circuit ecm thermal overload starter relay circuit open or shorted to voltage starter relay circuit short circuit starter relay circuit short to ground steering angle sensor plausibility tcm dtc 1-2 and 4-5 shift solenoid fault present tcm dtc 2-3 shift solenoid fault present tcm dtc 3-4 shift solenoid fault present tcm dtc can msg implausible fault present tcm dtc ewm can message fault present tcm dtc internal fault present tcm dtc modulating pressure solenoid fault present tcm dtc negative gear comparison fault present tcm dtc not unequivocal fault present tcm dtc right rear wheel speed implausible fault present tcm dtc shift pressure solenoid fault present tcm dtc speed sensor voltage fault present tcm dtc tcc excessive power consumption fault present tcm dtc torque converter clutch solenoid fault present tcm dtc transmission ratio error fault present tcm dtc valve voltage supply fault present tcm message error tcm no can message torque reduction message from abs -can plausibility torque reduction message from abs -message error torque reduction message from abs -messages missing torque reduction message from abs -no communication torque reduction message from abs -plausibility #1 torque reduction message from abs plausibility #2 torque reduction message from hvac switch signal plausibility torque reduction message from hvac-parity error torque reduction message from hvac-switch signal error torque reduction message from tcm -can plausibility torque reduction message from tcm -engine stop torque reduction message from tcm -message error torque reduction message from tcm -messages missing torque reduction message from tcm -plausibility torque reduction message from tcm -tcm dtc #1 torque reduction message from tcm -tcm dtc #2 water in fuel sensor signal error water in fuel sensor -water in fuel wheel speed sensor plaus -can bus message from abs write error to eeprom
GENERAL INFORMATION
3.3.4 HANDLING NO TROUBLE CODE PROBLEMS 4.0 DISCLAIMERS, SAFETY, WARNINGS DISCLAIMERS
After reading Section 3.0 (System Description and Functional Operation), you should have a better understanding of the theory and operation of the on-board diagnostics and how this relates to the diagnosis of a vehicle that may have a driveabilityrelated symptom or complaint. When there are no trouble codes present, refer to the no trouble code (*) tests.
4.1
All information, illustrations and specifications contained in this manual are based on the latest information available at the time of publication. The right is reserved to make changes at any time without notice.
3.4
USING THE DRBIII
4.2 4.2.1
SAFETY TECHNICIAN SAFETY INFORMATION
Refer to the DRBIII users guide for instructions and assistance with reading the DTCs, erasing the DTCs, lab scope usage and other DRBIII functions.
3.4.1
DRBIII DOES NOT POWER UP
If the LEDs do not light or no sound is emitted at start up, check for loose cable connections or a bad cable. Check the vehicle battery voltage at data link connector cavity 16. A minimum of 11.0 volts is required to adequately power the DRBIII . Check for proper ground connection at data link connector cavities 4 and 5. If all connections are proper between the DRBIII and the vehicle or other devices, and the vehicle battery is fully charged, an inoperative DRBIII may be the result of a faulty cable or vehicle wiring. For a blank screen, refer to the appropriate diagnostic manual.
WARNING: HIGH-PRESSURE FUEL LINES DELIVER DIESEL FUEL UNDER EXTREME PRESSURE FROM THE INJECTION PUMP TO THE FUEL INJECTORS. THIS MAY BE AS HIGH AS 23,200 PSI (1600 BAR). USE EXTREME CAUTION WHEN INSPECTING FOR HIGH-PRESSURE FUEL LEAKS. FUEL UNDER THIS AMOUNT OF PRESSURE CAN PENETRATE SKIN CAUSING PERSONAL INJURY OR DEATH. INSPECT FOR HIGH-PRESSURE FUEL LEAKS WITH A SHEET OF CARDBOARD. WEAR SAFETY GOGGLES AND ADEQUATE PROTECTIVE CLOTHING WHEN SERVICING FUEL SYSTEM. WARNING: ENGINES PRODUCE CARBON MONOXIDE THAT IS ODORLESS, CAUSES SLOWER REACTION TIME AND CAN LEAD TO SERIOUS INJURY. WHEN THE ENGINE IS OPERATING, KEEP SERVICE AREA WELL VENTILATED OR ATTACH THE VEHICLE EXHAUST SYSTEM TO THE SHOP EXHAUST REMOVAL SYSTEM.
Set the parking brake and block the wheels before testing or repairing the vehicle. It is especially important to block the wheels on front wheel drive vehicles; the parking brake does not hold the drive wheels. When servicing a vehicle, always wear eye protection and remove any metal jewelry such as watchbands or bracelets that might make electrical contact. When diagnosing powertrain system problems, it is important to follow approved procedures where applicable. These procedures can be found in the
3.4.2
DISPLAY IS NOT VISIBLE
Low temperatures will affect the visibility of the display. Adjust the contrast to compensate for this condition.
GENERAL INFORMATION
service manual. Following these procedures is very important to the safety of the individuals performing the diagnostic tests. Voltage between any terminal and ground must not exceed 500v DC or 500v peak AC. Use caution when measuring voltage above 25v DC or 25v AC. The circuit being tested must be protected by a 10 amp fuse or circuit breaker. Use the low current shunt to measure circuits up to 10 amps. Use the high current shunt to measure circuits exceeding 10 amps. When testing for the presence of voltage or current, make sure the meter is functioning correctly. Take a reading of a known voltage or current before accepting a zero reading. When measuring current, connect the meter in series with the load. Disconnect the live test lead before disconnecting the common test lead.
4.2.2
VEHICLE PREPARATION FOR TESTING
Make sure the vehicle being tested has a fully charged battery. If it does not, false diagnostic codes or error messages may occur.
4.2.3
SERVICING SUB-ASSEMBLIES
Some components of the powertrain system are intended to be serviced as an assembly only. Attempting to remove or repair certain system subcomponents may result in personal injury and/or improper system operation. Only those components with approved repair and installation procedures in the service manual should be serviced.
4.2.4
DRBIII SAFETY INFORMATION
4.3 4.3.1
WARNINGS AND CAUTIONS ROAD TEST WARNINGS
WARNING: EXCEEDING THE LIMITS OF THE DRBIII MULTIMETER IS DANGEROUS. IT CAN EXPOSE YOU TO SERIOUS OR POSSIBLE FATAL INJURY. CAREFULLY READ AND UNDERSTAND THE CAUTIONS AND SPECIFICATION LIMITS.
Follow the vehicle manufacturers service specifications at all times. Do not use the DRBIII if it has been damaged. Do not use the test leads if the insulation is damaged or if metal is exposed. To avoid electrical shock, do not touch the test leads, tip or the circuit being tested. Choose the proper range and function for the measurement. Do not try voltage or current measurements that may exceed the rated capacity. Do not exceed the limits shown in the table below: FUNCTION Volts Ohms (Resistance)* Frequency Measure Frequency Generated Temperature INPUT LIMIT 0500 peak volts AC 0500 volts DC 01.12 megaohms 010 kHz 58 +1100F 50 +600C
Some complaints will require a test drive as part of the repair verification procedure. The purpose of the test drive is to try to duplicate the diagnostic code or symptom condition.
CAUTION: Before road testing a vehicle, be sure that all components are reassembled. During the test drive, do not hang the DRBIII from the rear view mirror. Do not attempt to read the DRBIII while driving. Have an assistant available to operate the DRBIII .
4.3.2
VEHICLE DAMAGE CAUTIONS
Before disconnecting any control module, make sure the ignition is off. Failure to do so could damage the module. When testing voltage or circuit integrity at any control module, use the terminal side (not the wire end) of the harness connector. Do not probe through the insulation; this will damage it and eventually cause it to fail because of corrosion. Be careful when performing electrical test so as to prevent accidental shorting of terminals. Such a mistake can damage fuses or components. Also, a second code could be set, making diagnosis of the original problem more difficult.
5.0
REQUIRED TOOLS AND EQUIPMENT
* Ohms cannot be measured if voltage is present. Ohms can be measured only on a non-powered circuit.
9
DRBIII (diagnostic read-out box) scan tool vacuum gauge ammeter
GENERAL INFORMATION
ohmmeter voltmeter jumper wires and probes oscilloscope MAF MIL ms O2 PDC S/C A/C APP BCM BP CKP CMP CTM DLC ECM ECT EGR EOS IAT IP air conditioning accelerator pedal position (sensor) body control module boost pressure (sensor) crankshaft position (sensor) camshaft position (sensor) central timer module data link connector engine control module engine coolant temperature (sensor) exhaust gas recirculation (solenoid/ valve) engine oil sensor intake air temperature (sensor) intake pressure sensor SKREEM SRC WIF mass air flow (sensor) malfunction indicator lamp millisecond(s) oxygen sensor power distribution center speed control sentry key remote entry module signal range check water in fuel (sensor)
6.0
GLOSSARY OF TERMS
10
7.0 DIAGNOSTIC INFORMATION AND PROCEDURES
11
COMMUNICATION
Symptom: *NO RESPONSE FROM ENGINE CONTROL MODULE
POSSIBLE CAUSES CHECK POWERS AND GROUNDS TO THE ENGINE CONTROL MODULE K-ECM CIRCUIT SHORTED TO GROUND K-ECM CIRCUIT SHORTED TO VOLTAGE K-ECM CIRCUIT OPEN ENGINE CONTROL MODULE
TEST 1 ACTION Turn the ignition off. Disconnect the Engine Control Module harness connectors. Check each power and ground circuit to the module. Were any problems found? Yes Refer to the wiring diagrams located in the service information to help isolate an open or shorted condition. Repair as necessary. Perform ROAD TEST VERIFICATION - VER-2. Go To 2 All APPLICABILITY All
No 2
Turn the ignition off. Disconnect the ECM harness connectors. Disconnect the DRBIII from the DLC. Measure the resistance between ground and the K-ECM circuit. Is the resistance below 5.0 ohms? Yes No Repair the K-ECM circuit for a short to ground. Perform ROAD TEST VERIFICATION - VER-2. Go To 3
Turn the ignition off. Disconnect the DRBIII from the DLC. Disconnect the ECM harness connectors. Turn the ignition on. Using a 12-volt test light connected to ground, probe the K-ECM circuit. NOTE: The test light must illuminate brightly. Compare the brightness to that of a direct connection to the battery. Does the test light illuminate brightly? Yes No Repair the K-ECM circuit for a short to voltage. Perform ROAD TEST VERIFICATION - VER-2. Go To 4
All
12
COMMUNICATION
*NO RESPONSE FROM ENGINE CONTROL MODULE
TEST 4 ACTION Turn the ignition off. Disconnect the ECM harness connectors. Disconnect the DRBIII from the DLC. Measure the resistance of the K-ECM circuit between the ECM connector and the DLC. Is the resistance below 5.0 ohms? Yes Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Repair the K-ECM circuit for an open. Perform ROAD TEST VERIFICATION - VER-2.
Continued
APPLICABILITY All
No
13
COMMUNICATION
Symptom: *NO RESPONSE FROM SENTRY KEY REMOTE ENTRY MODULE
POSSIBLE CAUSES CHECK POWERS AND GROUNDS TO THE SENTRY KEY REMOTE ENTRY MODULE K-SKREEM CIRCUIT SHORTED TO GROUND K-SKREEM CIRCUIT SHORTED TO VOLTAGE K-SKREEM CIRCUIT OPEN SENTRY KEY REMOTE ENTRY MODULE
TEST 1 ACTION Turn the ignition off. Disconnect the SKREEM harness connector. Check each power and ground circuit to the module. Were any problems found? Yes Refer to the wiring diagrams located in the service information to help isolate an open or shorted condition. Repair as necessary. Perform BODY VERIFICATION TEST - VER 1. Go To 2 All APPLICABILITY All
No 2
Turn the ignition off. Disconnect the SKREEM harness connector. Disconnect the DRBIII from the DLC. Measure the resistance between ground and the K-SKREEM circuit. Is the resistance below 5.0 ohms? Yes No Repair the K-SKREEM circuit for a short to ground. Perform BODY VERIFICATION TEST - VER 1. Go To 3
Turn the ignition off. Disconnect the DRBIII from the DLC. Disconnect the SKREEM harness connector. Turn the ignition on. Using a 12-volt test light connected to ground, probe the K-SKREEM circuit. NOTE: The test light must illuminate brightly. Compare the brightness to that of a direct connection to the battery. Does the test light illuminate brightly? Yes No Repair the K-SKREEM circuit for a short to voltage. Perform BODY VERIFICATION TEST - VER 1. Go To 4
All
14
COMMUNICATION
*NO RESPONSE FROM SENTRY KEY REMOTE ENTRY MODULE
Continued
TEST 4 ACTION Turn the ignition off. Disconnect the SKREEM harness connector. Disconnect the DRBIII from the DLC. Measure the resistance of the K-SKREEM circuit between the SKREEM connector and the DLC. Is the resistance below 5.0 ohms? Yes Replace and program the Sentry Key Remote Entry Module in accordance with the Service Information. Perform BODY VERIFICATION TEST - VER 1. Repair the K-SKREEM circuit for an open. Perform BODY VERIFICATION TEST - VER 1. APPLICABILITY All
No
15
DRIVEABILITY - DIESEL
Symptom List: P-1105 ATMOSPHERIC PRESSURE SENSOR PLAUSIBILITY WITH BOOST PRESSURE SENSOR P1105-ATMOSPHERIC PRESSURE SENSOR SIGNAL VOLTAGE TOO HIGH P1105-ATMOSPHERIC PRESSURE SENSOR SIGNAL VOLTAGE TOO LOW P1617- ECM READ/WRITE ERROR P1617- ECM WRITE ERROR P1617-ECM INCORRECT VALUE P1617-ECM READ ERROR P2122-INTERNAL ERROR COUNTER FAULT P2122-INTERNAL ERROR ENGINE SHUT OFF P2122-INTERNAL ERROR ENGINE VOLTAGE MONITORING P2122-INTERNAL ERROR ENGINE VOLTAGE MONITORING P2123-INJECTOR BANK ERROR P2124-INJECTOR BANK ERROR P2139-ECM INJECTOR OUTPUT STAGE #1 P2139-ECM INJECTOR OUTPUT STAGE #1 SHORT CIRCUIT P2140-ECM INJECTOR OUTPUT STAGE #2 P2140-ECM INJECTOR OUTPUT STAGE #2 SHORT CIRCUIT P2149-ECM A/D CONVERTER HIGH P2149-ECM A/D CONVERTER LOW P2149-ECM A/D CONVERTER PLAUSIBILITY P2153-STARTER RELAY CIRCUIT ECM THERMAL OVERLOAD P2197-FUEL QUANTITY SOLENOID ECM THERMAL OVERLOAD P2214-CAN MESSAGE ERROR P2319-ECM INTERNAL ERROR 1 P2319-ECM INTERNAL ERROR 2 P2319-ECM INTERNAL ERROR 3 P2319-ECM INTERNAL ERROR 4 P2321-ECM INTERNAL ERROR 5 P2323-ECM INTERNAL ERROR P2324-ECM INJECTOR MONITORING 1 P2324-ECM INJECTOR MONITORING 2 P2324-ECM INJECTOR MONITORING 3 P2324-ECM INJECTOR MONITORING 4 P2324-ECM INJECTOR UNDERVOLTAGE P2325-ECM INTERNAL ERROR 1 P2325-ECM INTERNAL ERROR 2 P2325-ECM INTERNAL ERROR 3 P2325-ECM INTERNAL ERROR 4 P2329-ECM INTERNAL ERROR 1 P2330-ECM INTERNAL ERROR 1 P2340-ECM INJECTION QUANTITY ERROR P2342-ECM INTERNAL ERROR 1
16
P-1105 ATMOSPHERIC PRESSURE SENSOR PLAUSIBILITY WITH BOOST PRESSURE SENSOR Continued P2342-ECM INTERNAL ERROR 2 P2350-INTERNAL VOLTAGE ERROR P2352-INJECTION FAULT - EXCESSIVE TEMPERATURE P2352-INJECTION FAULT - QUANTITY ERROR P2352-INJECTION FAULT - TORQUE LIMIT P2352-INJECTION FAULT EXCESSIVE ENGINE SPEED P2354-ECM INTERNAL FAULT P2356-ECM INTERNAL ERROR P2357-ECM INTERNAL ERROR P2358-ECM INTERNAL ERROR P2500-FUEL PRESSURE SOLENOID CIRCUIT EXCESSIVE CURRENT P2514-CRANKCASE VENT HEATER EXCESSIVE CURRENT P2526-BOOST PRESSURE SERVO MOTOR EXCESSIVE CURRENT P2527-EGR VALVE EXCESSIVE CURRENT
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P-1105 ATMOSPHERIC PRESSURE SENSOR PLAUSIBILITY WITH BOOST PRESSURE SENSOR.
When Monitored and Set Condition: P1105-ATMOSPHERIC PRESSURE SENSOR SIGNAL VOLTAGE TOO HIGH When Monitored: Set Condition: With the ignition on.
The ECM internal Atmospheric Pressure Sensor is faulty.
P1105-ATMOSPHERIC PRESSURE SENSOR SIGNAL VOLTAGE TOO LOW When Monitored: Set Condition: With the ignition on.
The ECM internal Atmospheric Pressure Sensor is faulty.
P2500-FUEL PRESSURE SOLENOID CIRCUIT EXCESSIVE CURRENT When Monitored: With the ignition on.
Set Condition: The ECM detects an open or short to ground on the Fuel Pressure Solenoid Control circuit.
POSSIBLE CAUSES ENGINE CONTROL MODULE INTERMITTENT CONDITION
17
P-1105 ATMOSPHERIC PRESSURE SENSOR PLAUSIBILITY WITH BOOST PRESSURE SENSOR Continued
TEST 1 ACTION NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. NOTE: If there are other DTCs set with this DTC repair other DTCs before continuing with this diagnostic procedure. NOTE: This DTC indicates an internal ECM problem except in the case of DTC P2352 where it may indicate a fuel injector problem. Using the Service Information, check the fuel injectors for leakage before replacing the ECM. NOTE: This code can be caused by an intermittent problem in the wiring and connectors to the Engine Control Module. Inspect the Engine Control Module harness connector and associated wiring for signs of poor terminal contact. Turn the ignition on. With the DRBIII , erase ECM DTCs. Perform several engine run cycles, turning the ignition off for at least 20 seconds between each engine run cycle. With the DRBIII , read the ECM DTCs. Did this DTC set again? Yes Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Go To 2 All APPLICABILITY All
No 2
WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING. NOTE: The conditions that set the DTC are not present at this time. The following list may help in identifying the intermittent condition. With the engine running at normal operating temperature, monitor the DRB parameters related to the DTC while wiggling the wiring harness. Look for parameter values to change and/or a DTC to set. Review the DTC When Monitored and Set Conditions. If possible, try to duplicate the conditions under which the DTC was set. Refer to any Technical Service Bulletins (TSB) that may apply. Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or partially broken wires. Visually inspect the related wiring harness connectors. Look for broken, bent, pushed out, or corroded terminals. Were any of the above conditions present? Yes No Repair as necessary. Perform ROAD TEST VERIFICATION - VER-2. Test Complete.
18
Symptom List: P0100-MASS AIR FLOW SENSOR SIGNAL VOLTAGE TOO LOW P0100-MASS AIR FLOW SENSOR SIGNAL VOLTAGE TOO LOW P2011-MASS AIR FLOW SENSOR PLAUSIBILITY AIR MASS TOO HIGH P2011-MASS AIR FLOW SENSOR PLAUSIBILITY AIR MASS TOO LOW P2024-MASS AIR FLOW SENSOR SIGNAL VOLTAGE TOO HIGH P2024-MASS AIR FLOW SENSOR SIGNAL VOLTAGE TOO LOW P2065-MASS AIR FLOW SENSOR SUPPLY VOLTAGE TOO HIGH P2065-MASS AIR FLOW SENSOR SUPPLY VOLTAGE TOO LOW P2067-MASS AIR FLOW SENSOR SIGNAL CIRCUIT OPEN OR SHORTED P2067-MASS AIR FLOW SENSOR SIGNAL VOLTAGE TOO HIGH P2067-MASS AIR FLOW SENSOR SIGNAL VOLTAGE TOO LOW P2068-MASS AIR FLOW SENSOR PLAUSIBILITY SIGNAL RATIO ERROR P2633-MAF SENSOR SIGNAL PLAUSIBILITY
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P0100-MASS AIR FLOW SENSOR SIGNAL VOLTAGE TOO LOW.
When Monitored and Set Condition: P0100-MASS AIR FLOW SENSOR SIGNAL VOLTAGE TOO LOW When Monitored: Set Condition: P0100-MASS AIR FLOW SENSOR SIGNAL VOLTAGE TOO LOW When Monitored: Set Condition: P2011-MASS AIR FLOW SENSOR PLAUSIBILITY AIR MASS TOO HIGH When Monitored: Set Condition: With the ignition on. With the ignition on. With the ignition on.
The ECM detects a rationality problem with the MAF Sensor signal.
P2011-MASS AIR FLOW SENSOR PLAUSIBILITY AIR MASS TOO LOW When Monitored: Set Condition: With the ignition on.
The ECM detects a rationality problem with the MAF Sensor signal.
19
P0100-MASS AIR FLOW SENSOR SIGNAL VOLTAGE TOO LOW
Continued
P2024-MASS AIR FLOW SENSOR SIGNAL VOLTAGE TOO HIGH When Monitored: Set Condition: P2024-MASS AIR FLOW SENSOR SIGNAL VOLTAGE TOO LOW When Monitored: Set Condition: P2067-MASS AIR FLOW SENSOR SIGNAL VOLTAGE TOO HIGH When Monitored: Set Condition: With the ignition on. With the ignition on. With the ignition on.
The Mass Air Flow Sensor Signal voltage is above 4.8 volts.
P2067-MASS AIR FLOW SENSOR SIGNAL VOLTAGE TOO LOW When Monitored: Set Condition: With the ignition on.
The Mass Air Flow Sensor Signal voltage is below 0.2 volt.
P2068-MASS AIR FLOW SENSOR PLAUSIBILITY SIGNAL RATIO ERROR When Monitored: Set Condition: With the ignition on.
The ECM detects a rationality problem with the MAF Sensor.
POSSIBLE CAUSES 12 VOLT SUPPLY CIRCUIT OPEN CHECKING THE ENGINE CONTROL RELAY SYSTEM ECM - 5-VOLT SUPPLY CIRCUIT MASS AIRFLOW SENSOR SENSOR GROUND OPEN INTERMITTENT CONDITION MAF SENSOR 5 VOLT SUPPLY CIRCUIT OPEN MAF SENSOR SIGNAL CIRCUIT OPEN MAF 5 VOLT SUPPLY CIRCUIT SHORTED TO THE SENSOR GROUND CIRCUIT MAF SENSOR SIGNAL CIRCUIT SHORTED TO GROUND ECM SENSOR GROUND CIRCUIT OPEN MAF SENSOR 5 VOLT SUPPLY CIRCUIT SHORTED TO GROUND MAF SENSOR SIGNAL CIRCUIT SHORTED TO THE SENSOR GROUND CIRCUIT MAF SENSOR 5 VOLT SUPPLY CIRCUIT SHORTED TO VOLTAGE MAF SENSOR CIRCUIT SHORTED TO VOLTAGE
20
Continued
TEST 1 ACTION NOTE: If DTC P1611, P2306 or P2332 is present with this DTC, diagnose DTCs P1611, P2306 or P2332 before diagnosing this DTC. NOTE: Inspect all air intake and turbocharger related tubes for damage, restriction or poor connection. Any of these conditions can cause a this DTC to set. NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. Turn the ignition on. With the DRBIII , erase the ECM DTCs. Test drive the vehicle. With the DRBIII , read the ECM DTCs. Does the DRB III display a Mass Air Flow Sensor DTC? Yes No 2 Go To Go To 2 16 All APPLICABILITY All
NOTE: Check the ECM for other ECM DTCs related to circuits that are open, shorted to ground or low voltage problems. Does the DRB also display these type of DTCs? Yes No Go To Go To 3 4
Turn the ignition off. Disconnect the ECM harness connectors. Turn the ignition on. Connect a jumper wire between ground and the Engine Control Relay Signal circuit in ECM C2 harness connector cavity 44. Using a 12-volt test light connected to ground, check the Fused Engine Control Relay Output circuits at the ECM C1 harness connector cavities 1, 3 and 5. Does the test light illuminate brightly for each circuit? Yes No Go To 4
All
Refer to symptom list and perform Checking the ECM Power and Grounds. Perform ROAD TEST VERIFICATION - VER-2. All
NOTE: A malfunctioning EGR system can cause this DTC to set. Refer to symptom Checking the EGR System in the Driveability category to check EGR system operation. Turn the ignition off. Disconnect the MAF Sensor harness connector. Turn the ignition on. Measure the voltage of the MAF Sensor 5 Volt Supply circuit in MAF Sensor harness connector. Is the voltage between 4.8 and 5.2 volts? Yes No Go To Go To 5 12
21
Continued
TEST 5 ACTION Turn the ignition off. Disconnect the MAF Sensor harness connector. Disconnect the ECM harness connectors. Remove the Engine Control Relay. Connect a jumper wire between cavity 30 and cavity 87 of the Engine Control Relay connector. Turn the ignition on. Measure the voltage of the MAF Sensor Signal circuit. Is the voltage above 1.0 volt? Yes No 6 Repair the MAF Sensor Signal circuit for a short to voltage. Perform ROAD TEST VERIFICATION - VER-2. Go To 6 All APPLICABILITY All
Turn the ignition off. Disconnect the MAF Sensor harness connector. Disconnect the ECM harness connectors. Measure the resistance of the MAF Sensor Signal circuit. Is the resistance below 10.0 ohms? Yes No Go To 7
Repair the MAF Sensor Signal circuit for an open Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Disconnect the MAF Sensor harness connector. Disconnect the ECM harness connectors. Measure the resistance between ground and the MAF Sensor Signal circuit. Is the resistance below 1000 ohms? Yes No Repair the MAF Sensor Signal circuit for a short to ground. Perform ROAD TEST VERIFICATION - VER-2. Go To 8
Turn the ignition off. Disconnect the MAF Sensor harness connector. Disconnect the ECM harness connectors. Measure the resistance between the MAF Sensor Signal circuit and the Sensor Ground circuit at of the MAF Sensor harness connector. Is the resistance below 1000 ohms? Yes No Repair the MAF Sensor Signal for a short to Sensor Ground . Perform ROAD TEST VERIFICATION - VER-2. Go To 9
All
Turn the ignition off. Disconnect the MAF Sensor harness connector. Disconnect the ECM harness connectors. Measure the resistance of the Sensor Ground circuit between the MAF Sensor and the ECM. Is the resistance below 10.0 ohms? Yes No Go To 10
All
Repair the Sensor Ground circuit for an open. Perform ROAD TEST VERIFICATION - VER-2.
22
Continued
TEST 10 ACTION Turn the ignition off. Disconnect the MAF Sensor harness connector. Turn the ignition on. Measure the voltage between the 5-volt Supply circuit and the Sensor Ground circuit at the MAF Sensor harness connector. Is the voltage above 4.5 volts? Yes No Go To 11 APPLICABILITY All
Replace and program the ECM in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. All
11
Turn the ignition off. Disconnect the MAF Sensor harness connector. Turn the ignition on. Using a 12-volt test light connected to ground, probe the 12 Volt Supply circuit in the MAF Sensor harness connector Does the test light illuminate brightly? Yes No Replace the MAF Sensor. Perform ROAD TEST VERIFICATION - VER-2. Repair the 12 Volt Supply circuit for an open. Perform ROAD TEST VERIFICATION - VER-2.
12
Turn the ignition off. Disconnect the MAF Sensor harness connector. Disconnect the ECM harness connectors. Measure the resistance of the 5 Volt Supply circuit. Is the resistance below 10.0 ohms? Yes No Go To 13
All
Repair the MAF Sensor 5 Volt Supply circuit for an open. Perform ROAD TEST VERIFICATION - VER-2. All
13
Turn the ignition off. Disconnect the MAF Sensor harness connector. Disconnect the ECM harness connectors. Measure the resistance between the MAF Sensor 5 Volt Supply circuit and the Sensor Ground circuit at the MAF Sensor harness connector. Is the resistance above 1000 ohms? Yes No Go To 14
Repair the MAF 5 Volt Supply circuit for a short to the Sensor Ground circuit. Perform ROAD TEST VERIFICATION - VER-2. All
14
Turn the ignition off. Disconnect the MAF Sensor harness connector. Disconnect the ECM harness connectors. Measure the resistance between ground and the MAF Sensor 5 Volt Supply circuit at the MAF harness connector. Is the resistance below 1000 ohms? Yes No Repair the MAF Sensor 5 Volt Supply circuit for a short to ground. Perform ROAD TEST VERIFICATION - VER-2. Go To 15
23
Continued
TEST 15 ACTION Turn the ignition off. Disconnect the MAF Sensor harness connector. Disconnect the ECM harness connectors. Remove the Engine Control Relay. Connect a jumper wire between cavity 30 and cavity 87 of the Engine Control Relay connector. Turn the ignition on. Measure the voltage of the MAF Sensor 5 Volt Supply circuit in the ECM harness connector. Is the voltage above 1.0 volt? Yes No Repair the MAF Sensor 5 Volt Supply circuit for a short to voltage. Perform ROAD TEST VERIFICATION - VER-2. Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. All APPLICABILITY All
16
WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING. NOTE: The conditions that set the DTC are not present at this time. The following list may help in identifying the intermittent condition. With the engine running and at normal operating temperature, monitor the DRB parameters related to the DTC while wiggling the wiring harness. Look for parameter values to change and/or a DTC to set. Review the DTC When Monitored and Set Conditions. If possible, try to duplicate the conditions under which the DTC was set. Refer to any Technical Service Bulletins (TSB) that may apply. Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or partially broken wires. Visually inspect the related wiring harness connectors. Look for broken, bent, pushed out, or corroded terminals. Were any of the above conditions present? Yes No Repair as necessary. Perform ROAD TEST VERIFICATION - VER-2. Test Complete.
24
Symptom List: P0105-INTAKE PRESSURE SENSOR CAN MESSAGE ERROR P0105-INTAKE PRESSURE SENSOR PLAUSIBILITY
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P0105-INTAKE PRESSURE SENSOR CAN MESSAGE ERROR.
POSSIBLE CAUSES AIR FILTER AIR RESTRICTION INTERMITTENT CONDITION CAN BUS COMMUNICATION DTCS HIGH RESISTANCE IN THE INTAKE PRESSURE SENSOR SIGNAL CIRCUIT HIGH RESISTANCE IN THE INTAKE PRESSURE SENSOR GROUND CIRCUIT CAN BUS CIRCUITS OPEN TO THE SHIFTER MODULE HIGH RESISTANCE IN THE INTAKE PRESSURE SENSOR 5-VOLT SUPPLY CIRCUIT ENGINE CONTROL MODULE
TEST 1 ACTION NOTE: If DTC P1611, P2306 or P2332 is present with this DTC, diagnose DTCs P1611, P2306 or P2332 before diagnosing this DTC. NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. Turn the ignition on. With the DRB, erase ECM DTCs. Turn the ignition off, wait 30 seconds. Test drive the vehicle. With the DRB, read ECM DTCs. Did this DTC set again? Yes No 2 Go To Go To 2 9 All APPLICABILITY All
Turn the ignition off. Remove and inspect the Air Filter for soiling or excessive dirt and debris which may cause air flow restriction. Were any of these problems found? Yes No Replace the Air Filter element. Perform ROAD TEST VERIFICATION - VER-2. Go To 3
25
P0105-INTAKE PRESSURE SENSOR CAN MESSAGE ERROR
TEST 3 ACTION NOTE: Inspect all air intake and turbocharger related tubes for damage, restriction or poor connection. Any of these conditions can cause a this DTC to set. Turn the ignition off. Inspect all air intake and turbocharger related tubes and connections. Were any problems found? Yes No 4 Repair or replace as necessary. Perform ROAD TEST VERIFICATION - VER-2. Go To 4 All
Continued
APPLICABILITY All
With the DRBIII , read the active and stored DTCs for the Transmission Control Module. NOTE: Due to capabilities of certain controllers that use the CAN Bus, not all modules report CAN Bus DTCs. Is the TCM reporting active or stored CAN Bus communication DTCs related to the Shifter Module? Yes No Refer to symptom list to diagnose CAN Bus DTC in the TCM. Perform ROAD TEST VERIFICATION - VER-2. Go To 5
Turn the ignition off to the lock position. Disconnect the Shifter Module harness connector. Disconnect the ECM harness connector. NOTE: Check connectors - Clean/repair as necessary. Measure the resistance of both the CAN C Bus (+) circuit and the CAN C Bus (-) circuit between the Shifter Module harness connector and ECM harness connector. Is the resistance below 10.0 ohms for each measurement? Yes No Go To 6
All
Repair the CAN C Bus (+) and/or CAN C Bus (-) circuit for an open. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Disconnect the Intake Pressure Sensor harness connector. Disconnect the ECM harness connectors. Measure the resistance of the Intake Pressure Sensor Signal circuit. Is the resistance below 10.0 ohms? Yes No Go To 7
Repair the Intake Pressure Sensor Signal circuit for high resistance. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Disconnect the Intake Pressure Sensor harness connector. Disconnect the ECM harness connectors. Measure the resistance of the Sensor Ground circuit. Is the resistance below 10.0 ohms? Yes No Go To 8
Repair the Intake Pressure Sensor Ground circuit for high resistance. Perform ROAD TEST VERIFICATION - VER-2.
26
P0105-INTAKE PRESSURE SENSOR CAN MESSAGE ERROR
TEST 8 ACTION Turn the ignition off. Disconnect the Intake Pressure Sensor harness connector. Disconnect the ECM harness connectors. Measure the resistance of the Intake Pressure Sensor 5-volt Supply circuit. Is the resistance below 10.0 ohms? Yes Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Repair the Intake Pressure Sensor 5 Volt Supply circuit for high resistance. Perform ROAD TEST VERIFICATION - VER-2. All
Continued
APPLICABILITY All
No
27
Symptom: P0105-INTAKE PRESSURE SENSOR SIGNAL VOLTAGE TOO HIGH
When Monitored and Set Condition: P0105-INTAKE PRESSURE SENSOR SIGNAL VOLTAGE TOO HIGH When Monitored: Set Condition: With the ignition on.
Intake Pressure Sensor Signal voltage is 4.9 volts or greater.
POSSIBLE CAUSES INTERMITTENT CONDITION INTAKE PRESSURE SENSOR GROUND CIRCUIT SHORTED TO VOLTAGE INTAKE PRESSURE SENSOR SIGNAL CIRCUIT SHORTED TO VOLTAGE INTAKE PRESSURE SENSOR GROUND CIRCUIT OPEN INTAKE PRESSURE SENSOR POOR CONNECTOR TERMINAL CONTACT ENGINE CONTROL MODULE (INTERNAL) ENGINE CONTROL MODULE (SENSOR SIGNAL SHORTED TO VOLTAGE)
TEST 1 ACTION NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: If DTC P1611, P2306 or P2332 is present with this DTC, diagnose DTCs P1611, P2306 or P2332 before diagnosing this DTC. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. NOTE: Ensure all turbocharger inlet and outlet tubes are connected properly, without damage and restriction before continuing with this test. Also ensure the boost pressure servo motor and servo rod are attached and functioning properly. NOTE: If a Boost Pressure Servo Motor DTC is present with this DTC, diagnose that DTC before continuing. Turn the ignition on. With the DRB, erase ECM DTCs. Cycle the ignition key on and off several times, leaving the key on for at least 10 seconds at a time. With the DRB, read ECM DTCs. Did this DTC set again? Yes No Go To Go To 2 8 APPLICABILITY All
28
P0105-INTAKE PRESSURE SENSOR SIGNAL VOLTAGE TOO HIGH
Continued
TEST 2 ACTION Turn the ignition off. Disconnect the Intake Pressure Sensor harness connector. Disconnect the ECM harness connectors. Turn the ignition on. Measure the voltage between ground and the Intake Pressure Sensor Signal circuit. Is the voltage above 1.0 volt? Yes No 3 Go To Go To 3 4 All APPLICABILITY All
Turn the ignition off. Disconnect the Intake Pressure Sensor harness connector. Disconnect the ECM harness connectors. Remove the Engine Control Relay. Connect a jumper wire between cavity 30 and cavity 87 of the Engine Control Relay connector. Turn the ignition on. Measure the voltage between ground and the Intake Pressure Sensor Signal circuit. Is the voltage above 1.0 volt? Yes Repair the Intake Pressure Sensor Signal circuit for a short to voltage. Perform ROAD TEST VERIFICATION - VER-2. Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2.
No
Turn the ignition off. Disconnect the Intake Pressure Sensor harness connector. Disconnect the ECM harness connectors. Remove the Engine Control Relay. Connect a jumper wire between cavity 30 and cavity 87 of the Engine Control Relay connector. Turn the ignition on. Measure the voltage between ground and the Intake Pressure Sensor Ground circuit. Is the voltage above 1.0 volt? Yes Repair the Intake Pressure Sensor Ground circuit for a short to voltage. Note: The ECM will need to be checked for proper operation before the repair is completed. A short to voltage on a ground circuit can damage the ECM. Perform ROAD TEST VERIFICATION - VER-2. Go To 5
All
No
NOTE: If the Sensor Ground circuit had a short to voltage on it, the ECM could be damaged. 5 Turn the ignition off. Disconnect the Intake Pressure Sensor harness connector. Disconnect the ECM harness connectors. Measure the resistance of the Sensor Ground circuit. Is the resistance below 10.0 ohms? Yes No Go To 6 All
Repair the Intake Pressure Sensor Ground circuit for an open. Perform ROAD TEST VERIFICATION - VER-2.
29
Continued
TEST 6 ACTION Turn the ignition off. NOTE: Ensure all harness connectors are connected. Turn the ignition on. Measure the voltage of the Intake Pressure Sensor Signal circuit by back probing ECM harness connector C2, cavity 11. Is the voltage above 4.85 volts? Yes No 7 Replace the Intake Pressure Sensor. Perform ROAD TEST VERIFICATION - VER-2. Go To 7 All APPLICABILITY All
Turn the ignition on. With the DRB, read ECM DTCs. With the DRBIII , erase ECM DTCs. Did this DTC set again? Yes Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Ensure good terminal contact between the Intake Pressure Sensor harness connector and the sensor. The repair is complete. Perform ROAD TEST VERIFICATION - VER-2.
No
All
30
Symptom: P0105-INTAKE PRESSURE SENSOR SIGNAL VOLTAGE TOO LOW
When Monitored and Set Condition: P0105-INTAKE PRESSURE SENSOR SIGNAL VOLTAGE TOO LOW When Monitored: Set Condition: With the ignition on.
Intake Pressure Sensor Signal voltage is 0.2 volt or lower.
POSSIBLE CAUSES INTERMITTENT CONDITION INTAKE PRESSURE SENSOR 5 VOLT SUPPLY CIRCUIT OPEN INTAKE PRESSURE SENSOR INTAKE PRESSURE SENSOR SIGNAL CIRCUIT SHORTED TO GROUND INTAKE PRESSURE SENSOR SIGNAL AND GROUND CIRCUITS SHORTED TOGETHER ENGINE CONTROL MODULE INTAKE PRESSURE SENSOR SIGNAL CIRCUIT OPEN
TEST 1 ACTION NOTE: If DTC P1611, P2306 or P2332 is present with this DTC, diagnose DTCs P1611, P2306 or P2332 before diagnosing this DTC. Turn the ignition on. With the DRB, read the Intake Pressure Sensor voltage. Is the voltage below 0.3 volt? Yes No 2 Go To Go To 2 8 All APPLICABILITY All
Turn the ignition off. Disconnect the Intake Pressure Sensor harness connector. Turn the ignition on. Measure the voltage between ground and the Intake Pressure Sensor 5-Volt Supply circuit at the Intake Pressure Sensor harness connector. Is the voltage above 4.9 volts? Yes No Go To 3
Repair the Intake Pressure Sensor 5-Volt Supply circuit for an open. Perform ROAD TEST VERIFICATION - VER-2.
31
P0105-INTAKE PRESSURE SENSOR SIGNAL VOLTAGE TOO LOW
Continued
TEST 3 ACTION Turn the ignition off. Disconnect the Intake Pressure Sensor harness connector. Turn the ignition on. Connect a jumper wire between the Intake Pressure Sensor Signal circuit and the Intake Pressure Sensor 5-Volt Supply circuit. With the DRB, read the Intake Pressure Sensor voltage. Is the Intake Pressure Sensor voltage above 4.5 volts? Yes No 4 Replace the Intake Pressure Sensor. Perform ROAD TEST VERIFICATION - VER-2. Go To 4 All APPLICABILITY All
Turn the ignition off. Disconnect the Intake Pressure Sensor harness connector. Disconnect the ECM harness connectors. Measure the resistance between ground and the Intake Pressure Sensor Signal circuit. Is the resistance above 1000 ohms? Yes No Go To 5
Repair the Intake Pressure Sensor Signal circuit for a short to ground. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Disconnect the Intake Pressure Sensor harness connector. Disconnect the ECM harness connectors. Measure the resistance between the Intake Pressure Sensor Signal circuit and Sensor Ground circuit. Is the resistance above 1000 ohms? Yes No Go To 6
Repair the Intake Pressure Sensor Signal circuit for a short to the Sensor Ground circuit. Perform ROAD TEST VERIFICATION - VER-2. All
Repair the Intake Pressure Sensor Signal circuit for an open. Perform ROAD TEST VERIFICATION - VER-2. All
If there are no possible causes remaining, view repair. Repair Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2.
32
Continued
TEST 8 ACTION WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING. NOTE: The conditions that set the DTC are not present at this time. The following list may help in identifying the intermittent condition. With the engine running at normal operating temperature, monitor the DRB parameters related to the DTC while wiggling the wiring harness. Look for parameter values to change and/or a DTC to set. Review the DTC When Monitored and Set Conditions. If possible, try to duplicate the conditions under which the DTC was set. Refer to any Technical Service Bulletins (TSB) that may apply. Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or partially broken wires. Visually inspect the related wiring harness connectors. Look for broken, bent, pushed out, or corroded terminals. Were any of the above conditions present? Yes No Repair as necessary. Perform ROAD TEST VERIFICATION - VER-2. Test Complete. APPLICABILITY All
33
Symptom List: P0110-INTAKE AIR TEMP SENSOR SIGNAL VOLTAGE TOO HIGH P2063-INTAKE AIR TEMP SENSOR CIRCUIT SIGNAL VOLTAGE TOO HIGH
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P0110-INTAKE AIR TEMP SENSOR SIGNAL VOLTAGE TOO HIGH.
When Monitored and Set Condition: P0110-INTAKE AIR TEMP SENSOR SIGNAL VOLTAGE TOO HIGH When Monitored: Set Condition: With the ignition on.
The Intake Air Temperature Sensor Signal voltage is above 4.83 volts.
P2063-INTAKE AIR TEMP SENSOR CIRCUIT SIGNAL VOLTAGE TOO HIGH When Monitored: Set Condition: With the ignition on.
The Intake Air Temperature Sensor Signal voltage is above 4.83 volts.
POSSIBLE CAUSES CHECK FOR ACTIVE DTC INTERMITTENT CONDITION INTAKE AIR TEMP SENSOR SIGNAL CIRCUIT SHORTED TO VOLTAGE INTAKE AIR TEMP SENSOR GROUND CIRCUIT OPEN INTAKE AIR TEMP SENSOR SIGNAL CIRCUIT OPEN ENGINE CONTROL MODULE
TEST 1 ACTION NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. Turn the ignition on. With the DRB, erase ECM DTCs. Turn the ignition off for 10 seconds. Turn the ignition on. Monitor the DRB for ECM DTCs. Did this DTC set again? Yes No Go To Go To 2 5 APPLICABILITY All
34
P0110-INTAKE AIR TEMP SENSOR SIGNAL VOLTAGE TOO HIGH
Continued
TEST 2 ACTION Turn the ignition off. Disconnect the IAT Sensor harness connector. Disconnect the ECM harness connectors. Remove the Engine Control Relay. Connect a jumper wire between cavity 30 and cavity 87 of the Engine Control Relay connector. Turn the ignition on. Measure the voltage on the IAT Sensor Signal circuit. Is the voltage below 1.0 volt? Yes No Go To 3 APPLICABILITY All
Repair the Intake Air Temperature Sensor Signal circuit for a short to voltage. Perform ROAD TEST VERIFICATION - VER-2.
NOTE: Remove the jumper wire. 3 Turn the ignition off. Disconnect the ECM harness connectors. Disconnect the IAT Sensor harness connector. Measure the resistance of the Intake Air Temperature Sensor Signal circuit. Is the resistance below 10.0 ohms? Yes No Go To 4 All
Repair the Intake Air Temperature Sensor Signal circuit for an open. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Disconnect the IAT Sensor harness connector. Disconnect the ECM harness connectors. Measure the resistance of the Sensor Ground circuit between the ECM harness connector and the IAT Sensor harness connector. Is the resistance below 10.0 ohms? Yes Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Repair the Intake Air Temperature Sensor Ground circuit for an open. Perform ROAD TEST VERIFICATION - VER-2.
No
35
P0110-INTAKE AIR TEMP SENSOR SIGNAL VOLTAGE TOO HIGH
Continued
36
Symptom List: P0110-INTAKE AIR TEMP SENSOR SIGNAL VOLTAGE TOO LOW P2063-INTAKE AIR TEMP SENSOR CIRCUIT SIGNAL VOLTAGE TOO LOW
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P0110-INTAKE AIR TEMP SENSOR SIGNAL VOLTAGE TOO LOW.
When Monitored and Set Condition: P0110-INTAKE AIR TEMP SENSOR SIGNAL VOLTAGE TOO LOW When Monitored: With the ignition on.
Set Condition: The Intake Air Temperature Sensor Signal voltage is below 0.073 volt for more than 60 seconds. P2063-INTAKE AIR TEMP SENSOR CIRCUIT SIGNAL VOLTAGE TOO LOW When Monitored: With the ignition on.
Set Condition: The Intake Air Temperature Sensor Signal voltage is below 0.073 volt for more than 60 seconds.
POSSIBLE CAUSES INTERMITTENT CONDITION IAT SENSOR INTAKE AIR TEMP SENSOR SIGNAL CIRCUIT SHORTED TO GROUND INTAKE AIR TEMP SENSOR SIGNAL CIRCUIT SHORTED TO SENSOR GROUND ENGINE CONTROL MODULE
TEST 1 ACTION NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. Turn the ignition on. With the DRB, erase ECM DTCs. Monitor the DRB for ECM DTCs for at least 2 minutes. Did this DTC set again? Yes No Go To Go To 2 6 APPLICABILITY All
37
P0110-INTAKE AIR TEMP SENSOR SIGNAL VOLTAGE TOO LOW
Continued
TEST 2 ACTION Turn the ignition off. Disconnect the IAT Sensor harness connector. Turn the ignition on. Monitor the DRB for ECM DTCs for at least 2 minutes. Does the DRB display P0110 INTAKE AIR TEMP SIGNAL VOLTAGE TOO HIGH? Yes No 3 Replace the Intake Air Temperature Sensor. Perform ROAD TEST VERIFICATION - VER-2. Go To 3 All APPLICABILITY All
Turn the ignition off. Disconnect the ECM harness connectors. Disconnect the IAT Sensor harness connector. Measure the resistance between ground and the Intake Air Temperature Sensor Signal circuit. Is the resistance above 1000 ohms? Yes No Go To 4
Repair the Intake Air Temperature Sensor Signal circuit for a short to ground. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Disconnect the ECM harness connectors. Disconnect the IAT Sensor harness connector. Measure the resistance between the Intake Air Temperature Sensor Signal circuit and the Sensor Ground circuit. Is the resistance above 1000 ohms? Yes No Go To 5
Repair the Intake Air Temperature Sensor Signal circuit for a short to the Sensor Ground circuit. Perform ROAD TEST VERIFICATION - VER-2. All
38
P0110-INTAKE AIR TEMP SENSOR SIGNAL VOLTAGE TOO LOW
Continued
39
Symptom List: P0115-ENGINE COOLANT TEMP SENSOR CIRCUIT PLAUSIBILITY P2012-ENGINE COOLANT TEMP SENSOR CIRCUIT PLAUSIBILITY
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P0115-ENGINE COOLANT TEMP SENSOR CIRCUIT PLAUSIBILITY.
POSSIBLE CAUSES ECT SENSOR ECT SENSOR - COLD ECT SENSOR - HOT HGH RESISTANCE IN ECT SENSOR CIRCUITS ENGINE COLD TOO LONG
TEST 1 ACTION Note: The best way to diagnose this DTC is to allow the vehicle to remain outside overnight in order to have a completely cold soaked engine. Note: Extremely cold outside ambient temperatures may cause this DTC to set. Verify that the coolant level is correct. Start the engine. With the DRBIII , set the engine RPM to 1500 and allow the engine to warm up for 10-15 minutes. With the DRBIII , monitor the Engine Coolant Temperature value during the warm up cycle. Make sure the transition of temperature change is smooth. Did the engine temperature reach a minimum of 80 C (176 F)? Yes No Go To 2 APPLICABILITY All
Refer to the Service Information for cooling system performance diagnosis. The most probable cause is a Thermostat problem. Also, refer to any related TSBs. Perform ROAD TEST VERIFICATION - VER-2. All
NOTE: The engine temperature must be below 50C (120F) for this test. NOTE: The thermostat must be operating correctly for this test to be valid. With the DRBIII in Sensors, read and note the engine coolant temperature. Using a temperature probe, measure the engine block temperature near the ECT Sensor. Are the readings within 7C (13F) of each other? Yes No Go To Go To 3 4
40
P0115-ENGINE COOLANT TEMP SENSOR CIRCUIT PLAUSIBILITY
Continued
TEST 3 ACTION NOTE: The thermostat must be operating correctly for this test to be valid. Start the engine and bring the engine to operating temperature (thermostat open). Turn the engine off and wait 10 minutes to allow the engine temperature to stabilize. Using a temperature probe, measure the engine block temperature near the ECT Sensor. With the DRBIII , select Engine, then Sensors and read the engine coolant temperature. Are the readings within 7C (13F) of each other? Yes No 4 Test Complete. Go To 4 All APPLICABILITY All
Disconnect the ECT harness connector. Disconnect the ECM harness connectors. Measure the resistance of the ECT Sensor Signal circuit between the ECM harness connector and the ECT harness connector. Measure the resistance of the Sensor Ground circuit between the ECM harness connector and the ECT harness connector. Is the resistance below 10.0 ohms for each measurement? Yes No Replace the Engine Coolant Temperature Sensor. Perform ROAD TEST VERIFICATION - VER-2. Repair the ECT Sensor circuit(s) that measured above 10.0 ohms for high resistance. Perform ROAD TEST VERIFICATION - VER-2.
41
Symptom: P0115-ENGINE COOLANT TEMP SENSOR CIRCUIT PLAUSIBILITY WITH ENGINE OIL SENSOR
When Monitored and Set Condition: P0115-ENGINE COOLANT TEMP SENSOR CIRCUIT PLAUSIBILITY WITH ENGINE OIL SENSOR When Monitored: Set Condition: EOS Sensor. With the engine running.
The ECT Sensor signal indicates a different engine temperature than the
POSSIBLE CAUSES CURRENT DTC ECT SENSOR ECT SENSOR - COLD ECT SENSOR - HOT ENGINE OIL SENSOR SENSOR HGH RESISTANCE IN ECT SENSOR CIRCUITS ENGINE COLD TOO LONG
TEST 1 ACTION Verify that the coolant level is correct. Start the engine. NOTE: The thermostat must be operating correctly for this test to be valid. With the DRBIII , erase ECM DTCs. With the DRBIII , set the engine RPM to 1500 and allow the engine to warm up for 10-15 minutes. With the DRBIII , monitor the Engine Coolant Temperature value during the warm up cycle. Make sure the transition of temperature change is smooth. Did the engine temperature reach a minimum of 80 C (176 F)? Yes No Go To 2 APPLICABILITY All
Refer to the Service Information for cooling system performance diagnosis. The most probable cause is a Thermostat problem. Also, refer to any related TSBs. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition on. With the DRBIII , read the ECM DTCs. Did this DTC return after performing the previous test? Yes No Go To 3
Check for possible connecor or wiring problems at the ECT sensor that may cause an intermittent problem. Repair as necessary. Test Complete. Perform ROAD TEST VERIFICATION - VER-2.
42
P0115-ENGINE COOLANT TEMP SENSOR CIRCUIT PLAUSIBILITY WITH ENGINE OIL SENSOR Continued
TEST 3 ACTION NOTE: The engine temperature must be below 50C (120F) for this test. NOTE: The thermostat must be operating correctly for this test to be valid. With the DRBIII in Sensors, read and note the engine coolant temperature. Using a temperature probe, measure the engine block temperature near the ECT Sensor. Are the readings within 7C (13F) of each other? Yes No 4 Go To Go To 4 5 All APPLICABILITY All
NOTE: The thermostat must be operating correctly for this test to be valid. Start the engine and bring the engine to operating temperature (thermostat open). Turn the engine off and wait 10 minutes to allow the engine temperature to stabilize. Using a temperature probe, measure the engine block temperature near the ECT Sensor. With the DRBIII , select Engine, then Sensors and read the engine coolant temperature. Are the readings within 7C (13F) of each other? Yes No Replace the Engine Oil Sensor. Perform ROAD TEST VERIFICATION - VER-2. Go To 5
Disconnect the ECT harness connector. Disconnect the ECM harness connectors. Measure the resistance of the ECT Sensor Signal circuit between the ECM harness connector and the ECT harness connector. Measure the resistance of the Sensor Ground circuit between the ECM harness connector and the ECT harness connector. Is the resistance below 10.0 ohms for each measurement? Yes No Replace the Engine Coolant Temperature Sensor. Perform ROAD TEST VERIFICATION - VER-2. Repair the ECT Sensor circuit(s) that measured above 10.0 ohms for high resistance. Perform ROAD TEST VERIFICATION - VER-2.
All
43
Symptom List: P0115-ENGINE COOLANT TEMP SENSOR CIRCUIT SIGNAL VOLTAGE TOO HIGH P2054-ENGINE COOLANT TEMP SENSOR CIRCUIT SIGNAL VOLTAGE TOO HIGH P2054-ENGINE COOLANT TEMP SENSOR CIRCUIT SIGNAL VOLTAGE TOO LOW
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P0115-ENGINE COOLANT TEMP SENSOR CIRCUIT SIGNAL VOLTAGE TOO HIGH.
When Monitored and Set Condition: P0115-ENGINE COOLANT TEMP SENSOR CIRCUIT SIGNAL VOLTAGE TOO HIGH When Monitored: With the ignition on.
Set Condition: The Engine Coolant Temperature Sensor Signal voltage is above 4.98 volts for more than 3 seconds. P2054-ENGINE COOLANT TEMP SENSOR CIRCUIT SIGNAL VOLTAGE TOO HIGH When Monitored: With the ignition on.
Set Condition: The Engine Coolant Temperature Sensor Signal voltage is above 4.98 volts for more than 3 seconds. P2054-ENGINE COOLANT TEMP SENSOR CIRCUIT SIGNAL VOLTAGE TOO LOW When Monitored: Set Condition: With the ignition on.
POSSIBLE CAUSES INTERMITTENT CONDITION ECM ECT SENSOR SIGNAL CIRCUIT SHORTED TO VOLTAGE ECT SENSOR GROUND CIRCUIT OPEN ECT SENSOR ECT SENSOR SIGNAL CIRCUIT OPEN ENGINE CONTROL MODULE
44
P0115-ENGINE COOLANT TEMP SENSOR CIRCUIT SIGNAL VOLTAGE TOO HIGH Continued
TEST 1 ACTION NOTE: If multiple DTCs are present, the most likely cause is a 5-Volt Supply or Sensor Ground circuit shorted to voltage or ground. Refer to the Service Information Wiring section for circuits that would affect multiple DTCs. NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. Turn the ignition on. With the DRB, monitor the Engine Coolant Temperature (ECT) Sensor voltage. Is the ECT Sensor voltage above 4.90 volts? Yes No 2 Go To Go To 2 7 All APPLICABILITY All
Turn the ignition off. Disconnect the ECT Sensor harness connector. Turn the ignition on. Measure the voltage on the ECT Sensor Signal circuit. Is the voltage above 5.5 volts? Yes No Repair the ECT Sensor Signal circuit for a short to voltage. Perform ROAD TEST VERIFICATION - VER-2. Go To 3
Turn the ignition off. Disconnect the ECT Sensor harness connector. Connect a jumper wire between the ECT Sensor harness connector cavities. Turn the ignition on. With the DRB, read the ECT Sensor voltage. Is the voltage below 1.0 volt? Yes Replace the ECT Sensor in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Go To 4
All
No 4
Turn the ignition off. Disconnect the ECT Sensor harness connector. Disconnect the ECM harness connectors. Measure the resistance of the ECT Sensor Ground circuit. Is the resistance below 10.0 ohms? Yes No Go To 5
All
Repair the ECT Sensor Ground circuit for an open. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Disconnect the ECM harness connectors. Disconnect the ECT Sensor harness connector. Measure the resistance of the ECT Sensor Signal circuit. Is the resistance below 10.0 ohms? Yes No Go To 6
Repair the ECT Sensor Signal circuit for an open. Perform ROAD TEST VERIFICATION - VER-2.
45
P0115-ENGINE COOLANT TEMP SENSOR CIRCUIT SIGNAL VOLTAGE TOO HIGH Continued
TEST 6 ACTION If there are no possible causes remaining, view repair. Repair Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. 7 WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING. NOTE: The conditions that set the DTC are not present at this time. The following list may help in identifying the intermittent condition. With the engine running at normal operating temperature, monitor the DRB parameters related to the DTC while wiggling the wiring harness. Look for parameter values to change and/or a DTC to set. Review the DTC When Monitored and Set Conditions. If possible, try to duplicate the conditions under which the DTC was set. Refer to any Technical Service Bulletins (TSB) that may apply. Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or partially broken wires. Visually inspect the related wiring harness connectors. Look for broken, bent, pushed out, or corroded terminals. Were any of the above conditions present? Yes No Repair as necessary. Perform ROAD TEST VERIFICATION - VER-2. Test Complete. All APPLICABILITY All
46
Symptom: P0115-ENGINE COOLANT TEMP SENSOR CIRCUIT SIGNAL VOLTAGE TOO LOW
When Monitored and Set Condition: P0115-ENGINE COOLANT TEMP SENSOR CIRCUIT SIGNAL VOLTAGE TOO LOW When Monitored: With the ignition on.
Set Condition: The Engine Coolant Temperature Sensor Signal voltage is below 0.1 volt for more than 3 seconds.
POSSIBLE CAUSES INTERMITTENT CONDITION ECT SENSOR ECT SENSOR SIGNAL CIRCUIT SHORTED TO GROUND ECT SENSOR SIGNAL AND GROUND CIRCUITS SHORTED TOGETHER ENGINE CONTROL MODULE
TEST 1 ACTION NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. Turn the ignition on. With the DRB, monitor the Engine Coolant Temperature (ECT) Sensor voltage. Is the ECT Sensor voltage below 0.1 volt? Yes No 2 Go To Go To 2 6 All APPLICABILITY All
Turn the ignition off. Disconnect the ECT Sensor harness connector. Turn the ignition on. With the DRB, read the ECT Sensor voltage. Is the voltage above 4.0 volts? Yes Replace the ECT Sensor in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Go To 3
No
47
P0115-ENGINE COOLANT TEMP SENSOR CIRCUIT SIGNAL VOLTAGE TOO LOW Continued
TEST 3 ACTION Turn the ignition off. Disconnect the ECM harness connectors. Disconnect the ECT Sensor harness connector. Measure the resistance between ground and the ECT Sensor Signal circuit. Is the resistance above 1000 ohms? Yes No 4 Go To 4 APPLICABILITY All
Repair the ECT Sensor Signal circuit for a short to ground. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Disconnect the ECM harness connectors. Disconnect the ECT Sensor harness connector. Measure the resistance between the ECT Sensor Signal circuit and Sensor Ground circuit. Is the resistance above 1000 ohms? Yes No Go To 5
Repair the ECT Sensor Signal and Ground circuits for a short together. Perform ROAD TEST VERIFICATION - VER-2. All
All
48
Symptom: P0180-FUEL TEMPERATURE SENSOR CIRCUIT - SIGNAL VOLTAGE TOO HIGH
When Monitored and Set Condition: P0180-FUEL TEMPERATURE SENSOR CIRCUIT - SIGNAL VOLTAGE TOO HIGH When Monitored: Set Condition: With the ignition on.
The fuel temperature sensor signal voltage is above 4.7 volts.
POSSIBLE CAUSES INTERMITTENT CONDITION FUEL TEMPERATURE SENSOR GROUND CIRCUIT OPEN FUEL TEMPERATURE SENSOR SIGNAL CIRCUIT SHORTED TO VOLTAGE FUEL TEMPERATURE SENSOR FUEL TEMPERATURE SENSOR SIGNAL CIRCUIT OPEN ENGINE CONTROL MODULE
TEST 1 ACTION NOTE: If multiple DTCs are present, the most likely cause is a 5-Volt Supply or Sensor Ground circuit shorted to voltage or ground. Refer to the Service Information Wiring section for circuits that would affect multiple DTCs. NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. Turn the ignition on. With the DRB, monitor the Fuel Temperature Sensor voltage. Is the Fuel Temperature Sensor voltage above 4.80 volts? Yes No 2 Go To Go To 2 6 All APPLICABILITY All
Turn the ignition off. Disconnect the Fuel Temperature Sensor harness connector. Turn the ignition on. Measure the voltage on the Fuel Temperature Sensor Signal circuit. Is the voltage above 5.5 volts? Yes Repair the Fuel Temperature Sensor Signal circuit for a short to voltage. Perform ROAD TEST VERIFICATION - VER-2. Go To 3
No
49
P0180-FUEL TEMPERATURE SENSOR CIRCUIT - SIGNAL VOLTAGE TOO HIGH Continued
TEST 3 ACTION Turn the ignition off. Disconnect the Fuel Temperature Sensor harness connector. Connect a jumper wire between the Fuel Temperature Sensor harness connector cavities. Turn the ignition on. With the DRB, read the Fuel Temperature Sensor voltage. Is the voltage below 1.0 volt? Yes Replace the Fuel Temperature Sensor in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Go To 4 All APPLICABILITY All
No 4
Turn the ignition off. Disconnect the Fuel Temperature Sensor harness connector. Disconnect the ECM harness connectors. Measure the resistance of the Fuel Temperature Sensor Ground circuit. Is the resistance below 10.0 ohms? Yes No Go To 5
Repair the Fuel Temperature Sensor Ground circuit for an open. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Disconnect the ECM harness connectors. Disconnect the Fuel Temperature Sensor harness connector. Measure the resistance of the Fuel Temperature Sensor Signal circuit. Is the resistance below 10.0 ohms? Yes Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Repair the Fuel Temperature Sensor Signal circuit for an open. Perform ROAD TEST VERIFICATION - VER-2.
No 6
All
50
Symptom List: P0180-FUEL TEMPERATURE SENSOR CIRCUIT - SIGNAL VOLTAGE TOO LOW P2625-FUEL TEMPERATURE SENSOR PLAUSIBILITY
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P0180-FUEL TEMPERATURE SENSOR CIRCUIT - SIGNAL VOLTAGE TOO LOW.
When Monitored and Set Condition: P0180-FUEL TEMPERATURE SENSOR CIRCUIT - SIGNAL VOLTAGE TOO LOW When Monitored: Set Condition: With the ignition on.
The fuel temperature sensor signal voltage is below 0.8 volt.
P2625-FUEL TEMPERATURE SENSOR PLAUSIBILITY When Monitored: Set Condition: With the ignition on.
The Mass Air Flow Sensor Signal voltage is above 4.8 volts.
POSSIBLE CAUSES INTERMITTENT CONDITION FUEL TEMPERATURE SENSOR FUEL TEMPERATURE SENSOR SIGNAL CIRCUIT SHORTED TO GROUND FUEL TEMPERATURE SENSOR SIGNAL AND GROUND CIRCUITS SHORTED TOGETHER ENGINE CONTROL MODULE
TEST 1 ACTION NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. Turn the ignition on. With the DRB, monitor the Fuel Temperature Sensor voltage. Is the Fuel Temperature Sensor voltage below 0.10 volt? Yes No Go To Go To 2 5 APPLICABILITY All
51
P0180-FUEL TEMPERATURE SENSOR CIRCUIT - SIGNAL VOLTAGE TOO LOW Continued
TEST 2 ACTION Turn the ignition off. Disconnect the Fuel Temperature Sensor harness connector. Turn the ignition on. With the DRB, read the Fuel Temperature Sensor voltage. Is the voltage above 4.0 volts? Yes Replace the Fuel Temperature Sensor in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Go To 3 All APPLICABILITY All
No 3
Turn the ignition off. Disconnect the ECM harness connectors. Disconnect the Fuel Temperature Sensor harness connector. Measure the resistance between ground and the Fuel temperature Sensor Signal circuit. Is the resistance above 1000 ohms? Yes No Go To 4
Repair the Fuel Temperature Sensor Signal circuit for a short to ground. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Disconnect the ECM harness connectors. Disconnect the Fuel Temperature Sensor harness connector. Measure the resistance between the Fuel Temperature Sensor Signal circuit and Sensor Ground circuit. Is the resistance above 1000 ohms? Yes Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Repair the Fuel Temperature Sensor Signal and Ground circuits for a short together. Perform ROAD TEST VERIFICATION - VER-2.
No
WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING. NOTE: The conditions that set the DTC are not present at this time. The following list may help in identifying the intermittent condition. With the engine running at normal operating temperature, monitor the DRB parameters related to the DTC while wiggling the wiring harness. Look for parameter values to change and/or a DTC to set. Review the DTC When Monitored and Set Conditions. If possible, try to duplicate the conditions under which the DTC was set. Refer to any Technical Service Bulletins (TSB) that may apply. Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or partially broken wires. Visually inspect the related wiring harness connectors. Look for broken, bent, pushed out, or corroded terminals. Were any of the above conditions present? Yes No Repair as necessary. Perform ROAD TEST VERIFICATION - VER-2. Test Complete. 52
All
Symptom List: P0190-FUEL PRESS SENSOR CIRCUIT MALF SIGNAL VOLTAGE TOO HIGH P2008-FUEL PRESSURE SENSOR CIRCUIT SIGNAL VOLTAGE TOO HIGH
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P0190-FUEL PRESS SENSOR CIRCUIT MALF SIGNAL VOLTAGE TOO HIGH.
When Monitored and Set Condition: P0190-FUEL PRESS SENSOR CIRCUIT MALF SIGNAL VOLTAGE TOO HIGH When Monitored: Set Condition: With the ignition on.
The Fuel Rail Pressure Sensor Signal voltage is above 4.8 volts.
POSSIBLE CAUSES ECM - FUEL PRESSURE SENSOR SIGNAL CIRCUIT SHORTED TO VOLTAGE ECM - FUEL PRESSURE SENSOR SIGNAL OPEN FUEL PRESSURE SENSOR SIGNAL CIRCUIT OPEN FUEL PRESSURE SENSOR SIGNAL CIRCUIT SHORTED TO VOLTAGE SENSOR GROUND CIRCUIT OPEN INTERMITTENT CONDITION FUEL PRESSURE SENSOR 5-VOLT SUPPLY CIRCUIT OPEN SENSOR GROUND CIRCUIT SHORTED TO VOLTAGE FUEL PRESSURE SENSOR ENGINE CONTROL MODULE
53
P0190-FUEL PRESS SENSOR CIRCUIT MALF SIGNAL VOLTAGE TOO HIGH Continued
TEST 1 ACTION WARNING: THE FUEL INJECTION PUMP SUPPLIES HIGH-PRESSURE FUEL TO EACH INDIVIDUAL INJECTOR THROUGH HIGH-PRESSURE FUEL LINES. FUEL UNDER HIGH PRESSURE CAN PENETRATE SKIN AND CAUSE PERSONAL INJURY. WEAR SAFETY GOGGLES AND ADEQUATE PROTECTIVE CLOTHING. NOTE: If DTC P1611, P2306 or P2332 is present with this DTC, diagnose DTCs P1611, P2306 or P2332 before diagnosing this DTC. NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. Turn the ignition on. With the DRB, erase ECM DTCs. Cycle the ignition key on and off several times, leaving the key on for at least 10 seconds at a time. With the DRB, read ECM DTCs. Did this DTC set again? Yes No 2 Go To Go To 2 10 All APPLICABILITY All
Turn the ignition off. Disconnect the Fuel Pressure Sensor harness connector. Turn the ignition on. Measure the voltage of the Fuel Pressure Sensor Signal circuit. Select the appropriate voltage reading. Voltage is above 5.4 volts. Go To 3 Voltage is between 4.7 and 5.4 volts. Go To 4 Voltage is below 4.7 volts. Go To 9
Turn the ignition off. Disconnect the Fuel Pressure Sensor harness connector. Disconnect the ECM harness connectors. Remove the Engine Control Relay. Connect a jumper wire between cavity 30 and cavity 87 of the Engine Control Relay connector. Turn the ignition on. Measure the voltage of the Fuel Pressure Sensor Signal circuit. Is the voltage below 1.0 volt? Yes Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Repair the Fuel Pressure Sensor Signal circuit for a short to voltage. Perform ROAD TEST VERIFICATION - VER-2.
All
No
54
TEST 4 ACTION Turn the ignition off. Disconnect the Fuel Pressure Sensor harness connector. Disconnect the ECM harness connectors. Measure the resistance of the Sensor Ground circuit. Is the resistance below 10.0 ohms? Yes No 5 Go To 5 APPLICABILITY All
Repair the Sensor Ground circuit for an open. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Disconnect the Fuel Pressure Sensor harness connector. Disconnect the ECM harness connectors. Measure the resistance of the Fuel Pressure Sensor 5-Volt Supply circuit. Is the resistance below 10.0 ohms? Yes No Go To 6
Repair the Fuel Pressure Sensor 5-volt Supply circuit for an open. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Disconnect the Fuel Pressure Sensor harness connector. Disconnect the ECM harness connectors. Remove the Engine Control Relay. Connect a jumper wire between cavity 30 and cavity 87 of the Engine Control Relay connector. Turn the ignition on. Measure the voltage of the Sensor Ground circuit at the Fuel Pressure Sensor and ECM harness connectors. Is the voltage above 1.0 volt at either connector? Yes No Repair the Sensor Ground circuit for a short to voltage. Perform ROAD TEST VERIFICATION - VER-2. Go To 7
NOTE: If the Sensor Ground circuit had a short to voltage on it, the ECM could be damaged. Retest the Fuel Pressure Sensor circuit. 7 Turn the ignition off. Disconnect the Fuel Pressure Sensor harness connector. Connect a jumper wire between the Fuel Pressure Sensor Signal circuit and the Sensor Ground circuit in the Fuel Pressure Sensor harness connector. Turn the ignition on and monitor the DRB for DTCs. Is DTC P0190 FUEL PRESS SENSOR CIRCUIT MALF SIGNAL VOLTAGE TOO LOW present? Yes No 8 Replace the Fuel Pressure Sensor. Perform ROAD TEST VERIFICATION - VER-2. Go To 8 All All
55
TEST 9 ACTION Turn the ignition off. Disconnect the Fuel Pressure Sensor harness connector. Disconnect the ECM harness connectors. Measure the resistance of the Fuel Pressure Sensor Signal circuit. Is the resistance below 10.0 ohms? Yes Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Repair the Fuel Pressure Sensor Signal circuit for an open. Perform ROAD TEST VERIFICATION - VER-2. All APPLICABILITY All
No 10
56
Symptom List: P0190-FUEL PRESS SENSOR CIRCUIT MALF SIGNAL VOLTAGE TOO LOW P2008-FUEL PRESSURE SENSOR CIRCUIT SIGNAL VOLTAGE TOO LOW
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P0190-FUEL PRESS SENSOR CIRCUIT MALF SIGNAL VOLTAGE TOO LOW.
When Monitored and Set Condition: P0190-FUEL PRESS SENSOR CIRCUIT MALF SIGNAL VOLTAGE TOO LOW When Monitored: Set Condition: With the ignition on.
The Fuel Rail Pressure Sensor Signal voltage is below 0.2 volt.
POSSIBLE CAUSES FUEL PRESSURE SENSOR INTERMITTENT CONDITION FUEL PRESSURE SENSOR SIGNAL CIRCUIT SHORTED TO GROUND FUEL PRESSURE SENSOR SIGNAL CIRCUIT SHORTED TO SENSOR GROUND ECM - FUEL PRESSURE SENSOR SIGNAL SHORTED TO GROUND
TEST 1 ACTION WARNING: THE FUEL INJECTION PUMP SUPPLIES HIGH-PRESSURE FUEL TO EACH INDIVIDUAL INJECTOR THROUGH HIGH-PRESSURE FUEL LINES. FUEL UNDER HIGH PRESSURE CAN PENETRATE SKIN AND CAUSE PERSONAL INJURY. WEAR SAFETY GOGGLES AND ADEQUATE PROTECTIVE CLOTHING. NOTE: If DTC P1611, P2306 or P2332 is present with this DTC, diagnose DTCs P1611, P2306 or P2332 before diagnosing this DTC. NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. Turn the ignition on. With the DRB, erase ECM DTCs. Cycle the ignition key on and off several times, leaving the key on for at least 10 seconds at a time. With the DRB, read ECM DTCs. Did this DTC set again? Yes No Go To Go To 2 6 APPLICABILITY All
57
P0190-FUEL PRESS SENSOR CIRCUIT MALF SIGNAL VOLTAGE TOO LOW Continued
TEST 2 ACTION Turn the ignition off. Disconnect the Fuel Pressure Sensor harness connector. Turn the ignition on. Measure the voltage of the Fuel Pressure Sensor Signal circuit. Is the voltage between 4.7 and 5.3 volts? Yes No 3 Replace the Fuel Pressure Sensor. Perform ROAD TEST VERIFICATION - VER-2. Go To 3 All APPLICABILITY All
Turn the ignition off. Disconnect the Fuel Pressure Sensor harness connector. Disconnect the ECM harness connectors. Measure the resistance between ground and the Fuel Pressure Sensor Signal circuit. Is the resistance above 1000 ohms? Yes No Go To 4
Repair the Fuel Pressure Sensor Signal circuit for a short to ground. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Disconnect the Fuel Pressure Sensor harness connector. Disconnect the ECM harness connectors. Measure the resistance between the Sensor Ground circuit and the Fuel Pressure Sensor Signal circuit. Is the resistance above 1000 ohms? Yes No Go To 5
Repair the Fuel Pressure Sensor Signal circuit for a short to the Sensor Ground circuit. Perform ROAD TEST VERIFICATION - VER-2. All
58
P0190-FUEL PRESS SENSOR CIRCUIT MALF SIGNAL VOLTAGE TOO LOW Continued
TEST 6 ACTION WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING. NOTE: The conditions that set the DTC are not present at this time. The following list may help in identifying the intermittent condition. With the engine running and at normal operating temperature, monitor the DRB parameters related to the DTC while wiggling the wiring harness. Look for parameter values to change and/or a DTC to set. Review the DTC When Monitored and Set Conditions. If possible, try to duplicate the conditions under which the DTC was set. Refer to any Technical Service Bulletins (TSB) that may apply. Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or partially broken wires. Visually inspect the related wiring harness connectors. Look for broken, bent, pushed out, or corroded terminals. Were any of the above conditions present? Yes No Repair as necessary. Perform ROAD TEST VERIFICATION - VER-2. Test Complete. APPLICABILITY All
59
Symptom List: P0201-CYLINDER 1-INJECTOR CIRCUIT EXCESSIVE CURRENT P0201-CYLINDER 1-INJECTOR CIRCUIT OPEN OR SHORTED TO GROUND P0201-CYLINDER 1-INJECTOR CIRCUIT SHORTED TO GROUND P0201-CYLINDER 1-INJECTOR CIRCUIT SHORTED TO VOLTAGE P0202-CYLINDER 2-INJECTOR CIRCUIT EXCESSIVE CURRENT P0202-CYLINDER 2-INJECTOR CIRCUIT OPEN OR SHORTED TO GROUND P0202-CYLINDER 2-INJECTOR CIRCUIT SHORTED TO GROUND P0202-CYLINDER 2-INJECTOR CIRCUIT SHORTED TO VOLTAGE P0203-CYLINDER 3-INJECTOR CIRCUIT EXCESSIVE CURRENT P0203-CYLINDER 3-INJECTOR CIRCUIT OPEN OR SHORTED TO GROUND P0203-CYLINDER 3-INJECTOR CIRCUIT SHORTED TO GROUND P0203-CYLINDER 3-INJECTOR CIRCUIT SHORTED TO VOLTAGE P0204-CYLINDER 4-INJECTOR CIRCUIT EXCESSIVE CURRENT P0204-CYLINDER 4-INJECTOR CIRCUIT OPEN OR SHORTED TO GROUND P0204-CYLINDER 4-INJECTOR CIRCUIT SHORTED TO GROUND P0204-CYLINDER 4-INJECTOR CIRCUIT SHORTED TO VOLTAGE P0205-CYLINDER 5-INJECTOR CIRCUIT EXCESSIVE CURRENT P0205-CYLINDER 5-INJECTOR CIRCUIT OPEN OR SHORTED TO GROUND P0205-CYLINDER 5-INJECTOR CIRCUIT SHORTED TO GROUND P0205-CYLINDER 5-INJECTOR CIRCUIT SHORTED TO VOLTAGE P2123-INJECTOR CIRCUIT FAULT P2123-INJECTOR CIRCUIT LOW SIDE SHORTED TO GROUND P2123-INJECTOR CIRCUIT SHORTED TO GROUND OR VOLTAGE P2124-INJECTOR CIRCUIT FAULT P2124-INJECTOR CIRCUIT LOW SIDE SHORTED TO GROUND P2124-INJECTOR CIRCUIT SHORTED TO GROUND OR VOLTAGE P2141-CYLINDER #1 INJECTOR OPEN CIRCUIT P2142-CYLINDER #2 INJECTOR OPEN CIRCUIT P2143-CYLINDER #3 INJECTOR OPEN CIRCUIT P2144-CYLINDER #4 INJECTOR OPEN CIRCUIT P2145-CYLINDER #5 INJECTOR OPEN CIRCUIT
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P0201-CYLINDER 1-INJECTOR CIRCUIT EXCESSIVE CURRENT.
When Monitored and Set Condition:

60
P0201-CYLINDER 1-INJECTOR CIRCUIT EXCESSIVE CURRENT
Continued
P0201-CYLINDER 1-INJECTOR CIRCUIT EXCESSIVE CURRENT When Monitored: With the engine running.
Set Condition: The ECM detects excessive current through the Cylinder #1 Injector driver when on. P0201-CYLINDER 1-INJECTOR CIRCUIT OPEN OR SHORTED TO GROUND When Monitored: Set Condition: circuit. With the engine running.
The ECM detects an open or short to ground on the Cylinder #1 Injector
P0201-CYLINDER 1-INJECTOR CIRCUIT SHORTED TO GROUND When Monitored: Set Condition: With the engine running.
The ECM detects a short to ground on the Cylinder #1 Injector circuit.
P0201-CYLINDER 1-INJECTOR CIRCUIT SHORTED TO VOLTAGE When Monitored: Set Condition: With the engine running.
The ECM detects a short to voltage on the Cylinder #1 Injector circuit.
Set Condition: The ECM detects excessive current through the Cylinder #3 Injector driver when on.
61
Continued
P0203-CYLINDER 3-INJECTOR CIRCUIT OPEN OR SHORTED TO GROUND When Monitored: Set Condition: circuit. With the engine running.
62
Continued
POSSIBLE CAUSES CHECKING ECM POWER AND GROUNDS CHECKING THE ENGINE CONTROL RELAY SYSTEM ENGINE CONTROL MODULE INTERMITTENT CONDITION FUEL INJECTOR CONTROL CIRCUIT SHORTED TO VOLTAGE FUEL INJECTOR CONTROL CIRCUIT SHORTED TO GROUND FUEL INJECTOR CIRCUITS SHORTED TOGETHER FUEL INJECTOR CONTROL CIRCUIT OPEN FUEL INJECTOR
TEST 1 ACTION NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. Turn the ignition on. With the DRBIII , erase the ECM DTCs. Attempt to start the engine and test drive the vehicle. With the DRBIII , read the ECM DTCs. Did this DTC set again? Yes No Go To Go To 2 8 APPLICABILITY All
63
Continued
TEST 2 ACTION Turn the ignition off. Disconnect the ECM harness connectors. Connect a jumper wire between ground and the Engine Control Relay Control circuit in ECM C2 harness connector cavity 44. Turn the ignition on. Using a 12-volt test light connected to ground, check the Fused Engine Control Relay Output circuits at the ECM C2 harness connector cavities 1, 3 and 5. Choose the appropriate result. Test light is on for all circuits. Go To 3 Test light is on for 1 or 2 circuits Repair the Engine Control Relay Output circuit(s) that did not illuminate brightly for an open. Perform ROAD TEST VERIFICATION - VER-2. Light off for all circuits. Refer to symptom Checking the ECM Power and Grounds. Perform ROAD TEST VERIFICATION - VER-2. 3 Turn the ignition off. Disconnect all of the Cylinder Fuel Injector harness connectors. Disconnect the ECM harness connectors. Remove the Engine Control Relay from Fuse Block No.1 Connect a jumper wire between cavity 30 and cavity 87 of the Engine Control Relay connector in Fuse Block No.1. Turn the ignition on. Measure the voltage of all of the Fuel Injector Control circuit. Is the voltage above 1.0 volt for any of the measurements? Yes Repair the appropriate Fuel Injector Control circuit for a short to voltage. Perform ROAD TEST VERIFICATION - VER-2. Go To 4 All All APPLICABILITY All
No 4
Turn the ignition off. Disconnect the ECM harness connectors. Disconnect all of the Fuel Injector harness connectors. Measure the resistance between ground and all of the Fuel Injector Control circuit. Is the resistance below 1000 ohms for any of the measurements? Yes No Repair the Fuel Injector Control circuit for a short to ground. Perform ROAD TEST VERIFICATION - VER-2. Go To 5
Turn the ignition off. Disconnect the ECM harness connectors. Disconnect all of the Cylinder Fuel Injector harness connectors. Measure the resistance between Fuel Injector No. 1 harness connector cavities 1 and 2. Repeat the previous step for injectors 2, 3, 4, and 5. Is the resistance below 1000 ohms for any of the measurements? Yes Repair the Fuel Injector Control circuit and Common Driver circuit for a short together. Perform ROAD TEST VERIFICATION - VER-2. Go To 6
All
No
64
Continued
TEST 6 ACTION Turn the ignition off. Disconnect the ECM harness connectors. Disconnect all of the Cylinder Fuel Injector harness connectors. Measure the resistance of each Fuel Injector Control circuit between its respective injector harness connector and the ECM harness connector. Is the resistance below 10.0 ohms for each measurement? Yes No 7 Go To 7 APPLICABILITY All
Repair the appropriate Fuel Injector Control circuit for an open. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Replace the Cylinder Fuel Injector that was identified in the DTC in accordance with the Service Information. With the DRBIII , erase the ECM DTCs. Test drive the vehicle. With the DRBIII , read the ECM DTCs. Does the DRBIII display this DTC? Yes Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. The repair is complete. Perform ROAD TEST VERIFICATION - VER-2.
No 8
All
65
Symptom List: P0300-MISFIRE DETECTED P2113-MISFIRE CYLINDER #1 P2114-MISFIRE CYLINDER #2 P2115-MISFIRE CYLINDER #3 P2116-MISFIRE CYLINDER #4 P2117-MISFIRE CYLINDER #5 P2567-LEAKAGE CYLINDER #1 P2567-MISFIRE CYLINDER #1 P2568-LEAKAGE CYLINDER #2 P2568-MISFIRE CYLINDER #2 P2569-LEAKAGE CYLINDER #3 P2569-MISFIRE CYLINDER #3 P2570-LEAKAGE CYLINDER #4 P2570-MISFIRE CYLINDER #4 P2571-LEAKAGE CYLINDER #5 P2571-MISFIRE CYLINDER #5 P2573-GENERAL LEAKAGE P2574-INJECTOR 1 INJECTION P2574-INJECTOR 1 INJECTION P2575-INJECTOR 2 INJECTION P2575-INJECTOR 2 INJECTION P2576-INJECTOR 3 INJECTION P2576-INJECTOR 3 INJECTION P2577-INJECTOR 4 INJECTION P2577-INJECTOR 4 INJECTION P2578-INJECTOR 5 INJECTION P2578-INJECTOR 5 INJECTION
TIME ABOVE LIMIT TIME BELOW LIMIT TIME ABOVE LIMIT TIME BELOW LIMIT TIME ABOVE LIMIT TIME BELOW LIMIT TIME ABOVE LIMIT TIME BELOW LIMIT TIME ABOVE LIMIT TIME BELOW LIMIT
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P0300-MISFIRE DETECTED.
When Monitored and Set Condition: P0300-MISFIRE DETECTED When Monitored: Set Condition: With the engine running.
The ECM detects multiple misfires from one or more cylinders.
POSSIBLE CAUSES CHECKING FOR FUEL LEAKAGE CHECKING INJECTOR CLASSIFICATION
66
P0300-MISFIRE DETECTED
Continued
POSSIBLE CAUSES CORRECTION QUANTITY CHECK CYLINDER SPEED CHECK ENGINE COMPRESSION INJECTOR LEAKAGE INTERMITTENT CONDITION
TEST 1 ACTION NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. With the DRBIII , erase ECM DTCs. Test drive the vehicle and attempt to duplicate the problem. With the DRB, read ECM DTCs. Did this DTC set again? Yes No 2 Go To Go To 2 8 All APPLICABILITY All
Start and idle the engine for 5 minutes. Turn the ignition off. Inspect the fuel rail, fuel pressure sensor, fuel pressure solenoid and all fuel injectors for evidence of fuel leakage. Is there fuel leakage near any of the injectors or the fuel rail? Yes No Refer to the Service Information to repair fuel leakage. Perform ROAD TEST VERIFICATION - VER-2. Go To 3
Turn the ignition off. With the DRBIII , perform the Cylinder Compression Test. Is the cylinder compression within specification for all cylinders? Yes No Go To 4
All
Repair as necessary in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Read and note the six-digit code located on the top of each injector. Turn the ignition on. With the DRBIII , check the current programmed injector classifications to the six-digit codes from the vehicles current fuel injectors. Are all of the Fuel Injectors classified correctly? Yes No Go To 5
Using the DRB III, reset injectors to correct classification. Perform ROAD TEST VERIFICATION - VER-2.
67
P0300-MISFIRE DETECTED
TEST 5
Continued
APPLICABILITY All
ACTION With the DRBIII , select System Test, Smooth Eng Run Check, then Correction Quantity Check. Perform this test at Idle, 2000 rpm and 3000 rpm. NOTE: Readings per cylinder should be below 0.00450 mm3/stroke for each cylinder at each engine speed. Did any of the cylinders exceed 0.00450 mm3/stroke during this test? Yes Replace Fuel Injector of the cylinder(s) that had readings above 0.00450 mm3/stroke. Perform ROAD TEST VERIFICATION - VER-2. Go To 6
No 6
With the DRBIII , select System Test, Smooth Eng Run Check, then Cylinder Speed Check. NOTE: Readings for all cylinders should be close to each other. Look for one or two cylinders to differ high or low from the other cylinders. Did any of the cylinders differ significantly from the majority of the other cylinders? Yes Replace Fuel Injector of the cylinder(s) that had readings significantly above or below the other fuel injectors. Perform ROAD TEST VERIFICATION - VER-2. Go To 7
All
No 7
Turn the ignition off. Perform the INJECTOR LEAKAGE TEST in accordance with the Service Information. Were any problems found? Yes Repair or replace as necessary in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Test Complete.
All
No 8
All
68
Symptom: P0500-WHEEL SPEED SENSOR PLAUS - CAN BUS MESSAGE FROM ABS
When Monitored and Set Condition: P0500-WHEEL SPEED SENSOR PLAUS - CAN BUS MESSAGE FROM ABS When Monitored: Set Condition: seconds. With the ignition on.
The Boost Pressure Sensor Signal voltage exceeds 4.85 volts for at least 2
POSSIBLE CAUSES INTERMITTENT CONDITION CHECK FOR RELATED CONTROLLER ANTILOCK BRAKES DTCS CHECK FOR RELATED TRANSMISSION CONTROL MODULE DTCS ENGINE CONTROL MODULE
TEST 1 ACTION NOTE: If the ECM displays multiple CAN Bus related DTCs, check the CAN Bus circuits at the ECM harness connector for proper connection before continuing with this test. NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. Turn the ignition on. With the DRB, erase ECM DTCs. Test drive the vehicle. With the DRB, read the ECM DTCs. Does the DRB display this DTC? Yes No 2 Go To Go To 2 4 All APPLICABILITY All
Turn the ignition on. With the DRB, check for Controller Antilock Brakes DTCs. NOTE: The ECM Receives vehicle speed messages via CAB Bus from the ABS module. An interruption on the CAN Bus can cause this fault to set. Are any related CAB DTCs present? Yes Refer to symptom list for problems related to CAB DTCs before continuing. Perform ROAD TEST VERIFICATION - VER-2. Go To 3
No
69
P0500-WHEEL SPEED SENSOR PLAUS - CAN BUS MESSAGE FROM ABS Continued
TEST 3 ACTION NOTE: The TCM Receives vehicle speed messages via CAB Bus from the ABS module. An interruption on the CAN Bus can cause this fault to set. Turn the ignition on. With the DRB, check the TCM for DTCs. Are any ABS CAN Bus Message or Vehicle Speed related TCM DTCs present? Yes No Replace the CAB in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. All APPLICABILITY All
70
Symptom: P0600-CAN DATA BUS - BUS CIRCUIT FAULT
When Monitored and Set Condition: P0600-CAN DATA BUS - BUS CIRCUIT FAULT When Monitored: Set Condition: Bus circuit. With the ignition on.
The ECM detects an open, short to ground or short to voltage on the CAN
POSSIBLE CAUSES ENGINE CONTROL MODULE INTERMITTENT CONDITION CAN BUS COMMUNICATION DTCS CAN BUS CIRCUITS OPEN TO TCM
TEST 1 ACTION NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. Turn the ignition on. With the DRBIII , erase the ECM DTCs. Test drive the vehicle. With the DRBIII , read the ECM DTCs. Did this DTC set again? Yes No 2 Go To Go To 2 4 All APPLICABILITY All
With the DRBIII , read the active and stored DTCs for all modules that use CAN Bus communication. NOTE: Due to capabilities of certain controllers that use the CAN Bus, not all modules report CAN Bus DTCs. NOTE: If a total CAN Bus failure transpires, there will be multiple CAN Bus DTCs present in many modules. If the other modules are reporting Engine CAN Bus message faults or DTCs related to ECM CAN messages ONLY, answer No for the following question. Are other modules reporting active or stored CAN Bus communication DTCs? Yes No Refer to symptom list for problems related to CAN Bus Failure. Perform BODY VERIFICATION TEST - VER 1. Go To 3
71
P0600-CAN DATA BUS - BUS CIRCUIT FAULT
TEST 3 ACTION Turn the ignition off to the lock position. Disconnect the TCM C2 harness connector. Disconnect the ECM harness connector. NOTE: Check connectors - Clean/repair as necessary. Measure the resistance of both the CAN C Bus (+) circuit and the CAN C Bus (-) circuit between the TCM C2 harness connector and ECM harness connector. Is the resistance below 10.0 ohms for each measurement? Yes Replace the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Repair the CAN C Bus (+) and/or CAN C Bus (-) circuit for an open. Perform BODY VERIFICATION TEST - VER 1. All
Continued
APPLICABILITY All
No
WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING. NOTE: The conditions that set the DTC are not present at this time. The following list may help in identifying the intermittent condition. With the engine running at normal operating temperature, monitor the DRB parameters related to the DTC while wiggling the wiring harness. Look for parameter values to change and/or a DTC to set. Review the DTC When Monitored and Set Conditions. If possible, try to duplicate the conditions under which the DTC was set. Refer to any Technical Service Bulletins (TSB) that may apply. Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or partially broken wires. Visually inspect the related wiring harness connectors. Look for broken, bent, pushed out, or corroded terminals. Were any of the above conditions present? Yes No Repair as necessary. Perform BODY VERIFICATION TEST - VER 1. Test Complete.
72
Symptom List: P1222-ACC PEDAL POSITION SENSOR 1 CKT PLAUSIBILITY P1222-ACC PEDAL POSITION SENSOR 1 CKT SIGNAL VOLTAGE TOO HIGH P1222-ACC PEDAL POSITION SENSOR 1 CKT SIGNAL VOLTAGE TOO LOW P1234-ACC PEDAL POSITION SENSOR 2 CIRCUIT PLAUSIBILITY P1234-ACC PEDAL POSITION SENSOR 2 CKT SIGNAL VOLTAGE TOO HIGH P1234-ACC PEDAL POSITION SENSOR 2 CKT SIGNAL VOLTAGE TOO LOW P2327-APP SENSOR PLAUSIBILITY
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P1222-ACC PEDAL POSITION SENSOR 1 CKT PLAUSIBILITY.
POSSIBLE CAUSES ACCELERATOR PEDAL POSITION SENSOR ECM - APP SENSOR 1 5-VOLT SUPPLY CIRCUIT SENSOR GROUND OPEN (APP SENSOR) INTERMITTENT CONDITION APP SENSOR 5-VOLT SUPPLY CIRCUIT OPEN APP SENSOR SIGNAL CIRCUIT OPEN APP SENSOR 5-VOLT SUPPLY CIRCUIT SHORTED TO SENSOR GROUND APP SENSOR SIGNAL CIRCUIT SHORTED TO GROUND APP SENSOR 5-VOLT SUPPLY CIRCUIT SHORTED TO GROUND VERIFY APP SENSOR OPERATION APP SENSOR SIGNAL CIRCUIT SHORTED TO THE SENSOR GROUND CIRCUIT APP SENSOR 5-VOLT SUPPLY CIRCUIT SHORTED TO VOLTAGE ECM - SENSOR GROUND OPEN APP SENSOR CIRCUIT SHORTED TO VOLTAGE APP SENSOR GROUND CIRCUIT SHORTED TO VOLTAGE ECM - APP SENSOR SIGNAL CIRCUIT
73
P1222-ACC PEDAL POSITION SENSOR 1 CKT PLAUSIBILITY Continued
TEST 1 ACTION NOTE: If DTC P1611, P2306 or P2332 is present with this DTC, diagnose DTCs P1611, P2306 or P2332 before diagnosing this DTC. NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. NOTE: The APP Sensor is a device that contains 2 separate potentiometer type sensors. Each sensor has its own 5-volt supply circuit, sensor ground circuit and signal circuit. The APP Sensor no longer incorporates a low-idle switch. NOTE: The APP Sensor 2 signal should always be approximately 1/2 the voltage of the APP Sensor 1 signal. Turn the ignition on. Using a voltmeter, backprobe the APP Sensor 1 and APP Sensor 2 Signal circuits at the APP Sensor harness connector with the accelerator pedal in the at rest position. Is the voltage between 0.28 and 0.37 volt for sensor 1 and 0.10 and 0.19 volt for sensor 2? Yes No 2 Go To Go To 2 5 All APPLICABILITY All
Turn the ignition on. Fully depress the accelerator pedal. Using a voltmeter backprobe the APP Sensor harness connector and read the voltage for APP Sensor 1 and APP Sensor 2 Signal circuits. Is the voltage between 4.45 and 4.75 volts for #1 and 2.15 and 2.45 volts for #2? Yes No Go To Go To 3 5
Turn the ignition on. With the DRB, read the APP Sensor 1 and APP Sensor 2 percentages (%). With the accelerator pedal in the idle position, slowly depress the accelerator pedal until the pedal is fully depressed. NOTE: The percentage readings for APP Sensors 1 and 2 should increase smoothly as the pedal is depressed. NOTE: This test can also performed using a voltmeter by back probing each APP Sensor Signal circuit at the APP Sensor harness connector and observing the voltmeter for a smooth voltage change through the entire pedal travel. Does the percentage (voltage) increase smoothly for both readings with the accelerator pedal travel? Yes No Go To 4
All
Replace the Accelerator Pedal Position Sensor in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2.
74
TEST 4 ACTION WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING. NOTE: The conditions that set the DTC are not present at this time. The following list may help in identifying the intermittent condition. With the engine running and at normal operating temperature, monitor the DRB parameters related to the DTC while wiggling the wiring harness. Look for parameter values to change and/or a DTC to set. Review the DTC When Monitored and Set Conditions. If possible, try to duplicate the conditions under which the DTC was set by slowly pressing and releasing the accelerator pedal several times. Refer to any Technical Service Bulletins (TSB) that may apply. Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or partially broken wires. Visually inspect the related wiring harness connectors. Look for broken, bent, pushed out, or corroded terminals. Were any of the above conditions present? Yes No 5 Repair as necessary. Perform ROAD TEST VERIFICATION - VER-2. Test Complete. All APPLICABILITY All
NOTE: Perform the rest of this diagnostic procedure on the individual APP Sensor Potentiometer (1 or 2) that did not display the correct voltages in the previous test. Turn the ignition off. Disconnect the APP Sensor harness connector. Turn the ignition on. Measure the voltage of the 5-Volt Supply circuit in the APP Sensor harness connector. Is the voltage between 4.7 and 5.3 volts? Yes No Go To Go To 6 14
Turn the ignition off. Disconnect the APP Sensor harness connector. Connect a jumper wire between APP Sensor Signal circuit and the 5-volt supply circuit at the APP Sensor harness connector . With the DRB, read the PEDAL OUTPUT VOLTS. Does the DRB display between 4.0 and 5.5 volts? Yes No Go To Go To 7 10
All
Turn the ignition off. Disconnect the APP Sensor harness connector. Disconnect the ECM harness connectors. Remove the Engine Control Relay. Connect a jumper wire between cavity 30 and cavity 87 of the Engine Control Relay connector. Turn the ignition on. Measure the voltage of the APP Sensor Ground circuit. Is the voltage above 1.0 volt? Yes No Repair the App Sensor Ground circuit for a short to voltage. Perform ROAD TEST VERIFICATION - VER-2. Go To 8
All
75
TEST 8 ACTION Turn the ignition off. Disconnect the APP Sensor harness connector. Disconnect the ECM harness connectors. Measure the resistance of the Sensor Ground circuit between the APP Sensor and the ECM. Is the resistance below 10.0 ohms? Yes No 9 Go To 9 APPLICABILITY All
Repair the APP Sensor Ground circuit for an open. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Disconnect the APP Sensor harness connector. Using a 12-volt test light connected to 12-volts, check the Sensor Ground circuit of the appropriate potentiometer. Does the test light illuminate brightly? Yes No Replace the Accelerator Pedal Position Sensor. Perform ROAD TEST VERIFICATION - VER-2. Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2.
10
Turn the ignition off. Disconnect the APP Sensor harness connector. Disconnect the ECM harness connectors. Measure the resistance of the APP Sensor Signal circuit. Is the resistance below 10.0 ohms? Yes No Go To 11
All
Repair the APP Sensor Signal circuit for an open Perform ROAD TEST VERIFICATION - VER-2. All
11
Turn the ignition off. Disconnect the APP Sensor harness connector. Disconnect the ECM harness connectors. Measure the resistance between ground and the APP Sensor Signal circuit. Is the resistance below 1000 ohms? Yes No Repair the APP Sensor Signal circuit for a short to ground. Perform ROAD TEST VERIFICATION - VER-2. Go To 12
12
Turn the ignition off. Disconnect the APP Sensor harness connector. Disconnect the ECM harness connectors. Measure the resistance between the APP Sensor Signal circuit and the Sensor Ground circuit at the APP Sensor harness connector. Is the resistance below 1000 ohms? Yes Repair the APP Sensor Signal and Sensor Ground circuits for a short together. Perform ROAD TEST VERIFICATION - VER-2. Go To 13
All
No
76
TEST 13 ACTION Turn the ignition off. Disconnect the APP Sensor harness connector. Disconnect the ECM harness connectors. Remove the Engine Control Relay. Connect a jumper wire between cavity 30 and cavity 87 of the Engine Control Relay connector. Turn the ignition on. Measure the voltage of the APP Sensor Signal circuit. Is the voltage above 1.0 volt? Yes No Repair the APP Sensor Signal circuit for a short to voltage. Perform ROAD TEST VERIFICATION - VER-2. Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. All APPLICABILITY All
14
Turn the ignition off. Disconnect the APP Sensor harness connector. Disconnect the ECM harness connectors. Measure the resistance of the Accelerator Pedal Position Sensor 5-volt Supply circuit. Is the resistance below 10.0 ohms? Yes No Go To 15
Repair the Accelerator Pedal Position Sensor 5-Volt Supply circuit for an open. Perform ROAD TEST VERIFICATION - VER-2. All
15
Turn the ignition off. Disconnect the APP Sensor harness connector. Disconnect the ECM harness connectors. Measure the resistance between the Accelerator Pedal Position Sensor 5-Volt Supply circuit and both Sensor Ground circuits in the APP Sensor harness connector. Is the resistance above 1000 ohms? Yes No Go To 16
Repair the 5-Volt Supply circuit for a short to the Sensor Ground circuit. Perform ROAD TEST VERIFICATION - VER-2. All
16
Turn the ignition off. Disconnect the APP Sensor harness connector. Disconnect the ECM harness connectors. Measure the resistance between ground and the Accelerator Pedal Position Sensor 5-volt Supply circuit. Is the resistance below 1000 ohms? Yes Repair the Accelerator Pedal Position Sensor 5-Volt Supply circuit for a short to ground. Perform ROAD TEST VERIFICATION - VER-2. Go To 17
No
77
TEST 17 ACTION Turn the ignition off. Disconnect the APP Sensor harness connector. Disconnect the ECM harness connectors. Remove the Engine Control Relay. Connect a jumper wire between cavity 30 and cavity 87 of the Engine Control Relay connector. Turn the ignition on. Measure the voltage of the Accelerator Pedal Position Sensor 5-Volt Supply circuit in the ECM harness connector. Is the voltage above 1.0 volt? Yes Repair the Accelerator Pedal Position Sensor 5-Volt Supply circuit for a short to voltage. Perform ROAD TEST VERIFICATION - VER-2. Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. APPLICABILITY All
No
78
Symptom: P1480-GLOW PLUG INDICATOR ERROR
When Monitored and Set Condition: P1480-GLOW PLUG INDICATOR ERROR When Monitored: Witth the ignition on.
Set Condition: the ECM recieves a glow plug inidcator error message from the instrument cluster over the CAN Bus.
POSSIBLE CAUSES VERIFY CURRENT DTC

TEST 1 ACTION Turn the ignition on. With the DRBIII , erase the ECM DTCs. Perform several ignition key cycles leaving the ignition on for 10 seconds, then off for 10 seconds. With the DRBIII , read the ECM DTCs. Did this DTC set again? Yes Refer Refer to Instrument Cluster information for the related symptom(s). Perform ROAD TEST VERIFICATION - VER-2. Test Complete. APPLICABILITY All
No
79
Symptom List: P1482-GLOW P2537-GLOW P2537-GLOW GROUND P2537-GLOW VOLTAGE
PLUG MODULE - COMMUNICATION ERROR PLUG CONTROL CIRCUIT PREGLOW FAULT PLUG CONTROL CIRCUIT PREGLOW SHORT TO PLUG CONTROL CIRCUIT PREGLOW SHORT TO
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P1482-GLOW PLUG MODULE COMMUNICATION ERROR.
POSSIBLE CAUSES ENGINE CONTROL MODULE GLOW PLUG CONTROL SIGNAL CIRCUIT OPEN GLOW PLUG CONTROL SIGNAL CIRCUIT SHORTED TO GROUND GLOW PLUG CONTROL SIGNAL CIRCUIT SHORTED TO VOLTAGE GLOW PLUG MODULE INTERMITTENT CONDITION
TEST 1 ACTION NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. Turn the ignition on. With the DRB, erase ECM DTCs. Perform several engine run cycles, turning the ignition off for at least 20 seconds between each engine run cycle. Turn the ignition on. With the DRB, read ECM DTCs. Did this DTC set again? Yes No 2 Go To Go To 2 6 All APPLICABILITY All
Turn the ignition off. Disconnect the Glow Plug Module harness connectors. Disconnect the ECM harness connectors. Measure the resistance of the Glow Plug Control Signal circuit. Measure the resistance of the Glow Plug Module Control circuit. Is the resistance below 10.0 ohms? Yes No Go To 3
Repair the Glow Plug Control Signal circuit for an open. Perform ROAD TEST VERIFICATION - VER-2.
80
P1482-GLOW PLUG MODULE - COMMUNICATION ERROR
TEST 3 ACTION Turn the ignition off. Disconnect the Glow Plug Module harness connectors. Disconnect the ECM harness connectors. Measure the resistance between ground and the Glow Plug Control Signal circuit. Is the resistance above 1000 ohms? Yes No 4 Go To 4
Continued
APPLICABILITY All
Repair the Glow Plug Control Signal circuit for a short to ground. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Disconnect the Glow Plug Module harness connectors. Disconnect the ECM harness connectors. Remove the Engine Control Relay. Connect a jumper wire between cavity 30 and cavity 87 of the Engine Control Relay connector. Measure the voltage of the Glow Plug Control Signal circuit. Is the voltage below 1.0 volt? Yes No Go To 5
Repair the Glow Plug Control Signal circuit for a short to voltage. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Replace the Glow Plug Module in accordance with the Service Information. Turn the ignition on. With the DRBIII , erase ECM DTCs. Perform several engine run cycles, turning the ignition off for at least 20 seconds between each engine run cycle. With the DRBIII , read the ECM DTCs. Did this DTC set again? Yes Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Test Complete.
No 6
WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING. NOTE: The conditions that set the DTC are not present at this time. The following list may help in identifying the intermittent condition. With the engine running at normal operating temperature, monitor the DRB parameters related to the DTC while wiggling the wiring harness. Look for parameter values to change and/or a DTC to set. Review the DTC When Monitored and Set Conditions. If possible, try to duplicate the conditions under which the DTC was set. Refer to any Technical Service Bulletins (TSB) that may apply. Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or partially broken wires. Visually inspect the related wiring harness connectors. Look for broken, bent, pushed out, or corroded terminals. Were any of the above conditions present? Yes No Repair as necessary. Perform ROAD TEST VERIFICATION - VER-2. Test Complete. 81
All
Symptom List: P1482-GLOW P2133-GLOW P2133-GLOW P2133-GLOW P2133-GLOW P2134-GLOW P2134-GLOW P2134-GLOW P2134-GLOW P2135-GLOW P2135-GLOW P2135-GLOW P2135-GLOW P2136-GLOW P2136-GLOW P2136-GLOW P2136-GLOW P2137-GLOW P2137-GLOW P2137-GLOW P2137-GLOW
PLUG PLUG PLUG PLUG PLUG PLUG PLUG PLUG PLUG PLUG PLUG PLUG PLUG PLUG PLUG PLUG PLUG PLUG PLUG PLUG PLUG
MODULE - EXCESS CURRENT #1 CIRCUIT EXCESSIVE CURRENT #1 CIRCUIT OPEN CIRCUIT #1 CIRCUIT SHORT TO GROUND #1 CIRCUIT SHORT TO VOLTAGE #2 CIRCUIT EXCESSIVE CURRENT #2 CIRCUIT OPEN CIRCUIT #2 CIRCUIT SHORT TO GROUND #2 CIRCUIT SHORT TO VOLTAGE #3 CIRCUIT EXCESSIVE CURRENT #3 CIRCUIT OPEN CIRCUIT #3 CIRCUIT SHORT TO GROUND #3 CIRCUIT SHORT TO VOLTAGE #4 CIRCUIT EXCESSIVE CURRENT #4 CIRCUIT OPEN CIRCUIT #4 CIRCUIT SHORT TO GROUND #4 CIRCUIT SHORT TO VOLTAGE #5 CIRCUIT EXCESSIVE CURRENT #5 CIRCUIT OPEN CIRCUIT #5 CIRCUIT SHORT TO GROUND #5 CIRCUIT SHORT TO VOLTAGE
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P1482-GLOW PLUG MODULE EXCESS CURRENT.
POSSIBLE CAUSES GLOW PLUG GLOW PLUG CONTROL CIRCUIT OPEN GLOW PLUG CONTROL CIRCUIT SHORTED TO GROUND GLOW PLUG CONTROL CIRCUIT SHORTED TO VOLTAGE GLOW PLUG MODULE INTERMITTENT CONDITION
82
P1482-GLOW PLUG MODULE - EXCESS CURRENT
TEST 1 ACTION NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. Turn the ignition on. With the DRB, erase ECM DTCs. Perform several ignition cycles leaving the ignition on for at least 10 seconds then off for 10 seconds. With the DRBIII , read the ECM DTCs. Did this DTC set again? Yes No 2 Go To Go To 2 6 All
Continued
APPLICABILITY All
Turn the ignition off. Disconnect each Glow Plug harness connector. Disconnect the Glow Plug Module harness connector. Measure the resistance of each Glow Plug Control circuit. Is the resistance below 10.0 ohms for each circuit? Yes No Go To 3
Repair the appropriate Glow Plug Control circuit for an open. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Disconnect each Glow Plug harness connector. Disconnect the Glow Plug Module harness connector. Measure the resistance between ground and each Glow Plug Control circuit. Is the resistance below 1000.0 ohms for any of the measurements? Yes Repair the appropriate Glow Plug Control circuit for a short to ground. Perform ROAD TEST VERIFICATION - VER-2. Go To 4
No 4
Turn the ignition off. Disconnect each Glow Plug harness connector. Disconnect the Glow Plug Module harness connector. Turn the ignition on. Measure the voltage of each Glow Plug Control circuit. Is the voltage below 1.0 volt for each circuit? Yes No Go To 5
All
Repair the appropriate Glow Plug Control circuit for a short to voltage Perform ROAD TEST VERIFICATION - VER-2.
83
P1482-GLOW PLUG MODULE - EXCESS CURRENT
TEST 5 ACTION Turn the ignition off. With the DRBIII , erase ECM DTCs. Refer to the Service Information and perform the Glow Plug Test on each Glow plug. Did each Glow Plug pass the test? Yes No Replace the Glow Plug Module. Perform ROAD TEST VERIFICATION - VER-2. Replace the appropriate Glow Plug in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. All
Continued
APPLICABILITY All
84
Symptom List: P1482-GLOW P1482-GLOW P2538-GLOW P2538-GLOW P2538-GLOW
PLUG PLUG PLUG PLUG PLUG
MODULE MODULE MODULE MODULE MODULE
- INCORRECT TIMER - INTERNAL FAULT COMMUNICATION ERROR EXCESSIVE CURRENT ERROR TIMER ERROR
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P1482-GLOW PLUG MODULE INCORRECT TIMER.
POSSIBLE CAUSES GLOW PLUG MODULE INTERMITTENT CONDITION

TEST 1 ACTION NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. NOTE: This DTC indicates an internal Glow Plug Control Module problem or an incorrect Glow Plug Module has been installed. Turn the ignition on. With the DRBIII , erase ECM DTCs. Perform several engine run cycles, turning the ignition off for at least 20 seconds between each engine run cycle. With the DRBIII , read the ECM DTCs. Did this DTC set again? Yes Replace and program the Glow Plug Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Go To 2 APPLICABILITY All
No
85
P1482-GLOW PLUG MODULE - INCORRECT TIMER
TEST 2 ACTION WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING. NOTE: The conditions that set the DTC are not present at this time. The following list may help in identifying the intermittent condition. With the engine running at normal operating temperature, monitor the DRB parameters related to the DTC while wiggling the wiring harness. Look for parameter values to change and/or a DTC to set. Review the DTC When Monitored and Set Conditions. If possible, try to duplicate the conditions under which the DTC was set. Refer to any Technical Service Bulletins (TSB) that may apply. Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or partially broken wires. Visually inspect the related wiring harness connectors. Look for broken, bent, pushed out, or corroded terminals. Were any of the above conditions present? Yes No Repair as necessary. Perform ROAD TEST VERIFICATION - VER-2. Test Complete.
Continued
APPLICABILITY All
86
Symptom: P1610-ENGINE CONTROL RELAY PLAUSIBILITY
When Monitored and Set Condition: P1610-ENGINE CONTROL RELAY PLAUSIBILITY When Monitored: During after-run.
Set Condition: The internal ECM timer determines that the Engine Control Relay remains on for more than 2.0 seconds after the ECM has turned off the Engine Control Relay.
POSSIBLE CAUSES CHECK FOR OTHER DTCS CHECK THE ECM POWER AND GROUNDS ENGINE CONTROL MODULE INTERMITTENT CONDITION SUBSTITUTE ENGINE CONTROL RELAY
TEST 1 ACTION Turn the ignition on. With the DRB, check for additional DTCs. Are other DTCs present? Yes Refer to the Symptom List for diagnosis of the other DTCs before continuing. Perform ROAD TEST VERIFICATION - VER-2. Go To 2 All APPLICABILITY All
No 2
NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. Turn the ignition on. With the DRB, erase ECM DTCs. Perform several ignition key cycles, pausing for at least 10 seconds between each cycle. Turn the ignition on. With the DRB, read ECM DTCs. Did this DTC set again? Yes No Go To Go To 3 5
87
P1610-ENGINE CONTROL RELAY PLAUSIBILITY
TEST 3 ACTION Turn the ignition off. Install a substitute relay in place of the Engine Control Relay. Turn the ignition on. With the DRBIII , erase DTCs. Perform several ignition key cycles, pausing for at least 10 seconds between each cycle. Turn the ignition on. With the DRB, read ECM DTCs. Did this DTC set again? Yes No 4 Go To 4
Continued
APPLICABILITY All
Replace the Engine Control Relay. Perform ROAD TEST VERIFICATION - VER-2. All
Refer to symptom Checking the ECM Power and Grounds. Are the ECM Power and Ground circuits o.k.? Yes No Replace the ECM in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Repair as necessary. Perform ROAD TEST VERIFICATION - VER-2.
All
88
Symptom: P1610-ENGINE CONTROL RELAY SHUTS OFF TOO EARLY
When Monitored and Set Condition: P1610-ENGINE CONTROL RELAY SHUTS OFF TOO EARLY When Monitored: During after-run.
Set Condition: The internal ECM timer determines that the Engine Control Relay has shut off before the AFTER-RUN mode of operation has been completed.
POSSIBLE CAUSES CHECK FOR OTHER DTCS INTERMITTENT CONDITION SUBSTITUTE ENGINE CONTROL RELAY ENGINE CONTROL RELAY CONTROL CIRCUIT OPEN INTERMITTENTLY ENGINE CONTROL MODULE
No 2
89
P1610-ENGINE CONTROL RELAY SHUTS OFF TOO EARLY
TEST 3 ACTION Turn the ignition on. With the DRBIII , erase ECM DTCs. Turn the ignition off. Install a substitute relay in place of the Engine Control Relay. Perform several ignition key cycles, pausing for at least 10 seconds between each cycle. Turn the ignition on. With the DRB, read ECM DTCs. Did this DTC set again? Yes No 4 Go To 4
Continued
APPLICABILITY All
Turn the ignition off. Remove the Engine Control Relay. Disconnect the ECM harness connectors. Measure the resistance of the Engine Control Relay Control circuit while wiggling the wiring harness and connectors between the ECM and the Fuse Block #1. Was the resistance above 10.0 ohms at any time while wiggling the wiring harness and connectors? Yes Repair the Engine Control Relay Control circuit for an intermittent open. Perform ROAD TEST VERIFICATION - VER-2. Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2.
No
All
90
Symptom: P1610-ENGINE CONTROL RELAY SHUTS OFF TOO LATE
When Monitored and Set Condition: P1610-ENGINE CONTROL RELAY SHUTS OFF TOO LATE When Monitored: During after-run.
Set Condition: The internal ECM timer determines that the Engine Control Relay remains on for more than 2.0 seconds after the ECM has turned off the Engine Control Relay.
POSSIBLE CAUSES CHECK FOR OTHER DTCS INTERMITTENT CONDITION SUBSTITUTE ENGINE CONTROL RELAY ENGINE CONTROL RELAY CONTROL CIRCUIT SHORTED TO GROUND INTERMITTENTLY ENGINE CONTROL RELAY OUTPUT CIRCUIT SHORTED TO VOLTAGE ENGINE CONTROL MODULE
No 2
91
P1610-ENGINE CONTROL RELAY SHUTS OFF TOO LATE
TEST 3 ACTION Turn the ignition off. Install a substitute relay in place of the Engine Control Relay. Turn the ignition on. With the DRBIII , erase DTCs. Perform several ignition key cycles, pausing for at least 10 seconds between each cycle. Turn the ignition on. With the DRB, read ECM DTCs. Did this DTC set again? Yes No 4 Go To 4
Continued
APPLICABILITY All
Turn the ignition off. Remove the Engine Control Relay. Disconnect the ECM harness connectors. Measure the resistance between ground and the Engine Control Relay Control circuit while wiggling the wiring harness and connectors. Was the resistance below 1000.0 ohms at any time while wiggling the wiring harness and connectors? Yes Repair the Engine Control Relay Control circuit for an intermittent short to ground. Perform ROAD TEST VERIFICATION - VER-2. Go To 5
No 5
Turn the ignition off. Remove the Engine Control Relay. Turn the ignition on. Measure the voltage of the Engine Control Relay Output circuit. Is the voltage below 0.5 volt? Yes Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Repair the Engine Control Relay Output circuit for a short to voltage. Perform ROAD TEST VERIFICATION - VER-2.
All
No
92
P1610-ENGINE CONTROL RELAY SHUTS OFF TOO LATE
Continued
APPLICABILITY All
93
Symptom: P1611-SENSOR SUPPLY 1 VOLTAGE IS TOO HIGH
When Monitored and Set Condition: P1611-SENSOR SUPPLY 1 VOLTAGE IS TOO HIGH When Monitored: With the ignition on.
Set Condition: The ECM detects a short to voltage on the APP Sensor 5-volt Supply circuit or the CMP Sensor 5-volt Supply circuit.
POSSIBLE CAUSES VISUAL WIRING AND CONNECTOR INSPECTION INTERMITTENT CONDITION SENSOR SUPPLY 1 SHORTED TO VOLTAGE ENGINE CONTROL MODULE
TEST 1 ACTION NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. Turn the ignition on. With the DRB, erase ECM DTCs. Turn the ignition off for 10 seconds. Start the engine. Monitor the DRB for ECM DTCs. Did this DTC set again? Yes No 2 Go To Go To 2 4 All APPLICABILITY All
Turn the ignition off. Visually inspect the wiring and connectors associated with the APP and CMP Sensors for problems that may result in a short circuit. Were any problems found? Yes No Repair or replace wiring/connectors as necessary. Perform ROAD TEST VERIFICATION - VER-2. Go To 3
94
P1611-SENSOR SUPPLY 1 VOLTAGE IS TOO HIGH
TEST 3 ACTION Turn the ignition off. Disconnect the APP and CMP Sensor harness connectors. Disconnect the ECM harness connectors. Remove the Engine Control Relay. Connect a jumper wire between cavity 30 and cavity 87 of the Engine Control Relay connector in Fuse Block No.1. Turn the ignition on. Measure the voltage at ECM harness connector cavities C1-38, C1-37, C2-13, C2-24 and C2-25. Is the voltage above 1.0 volt for any of the measurements? Yes Repair the circuit(s) that measured above 1.0 volt for a short to voltage. Perform ROAD TEST VERIFICATION - VER-2. Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. All
Continued
APPLICABILITY All
No
95
Symptom: P1611-SENSOR SUPPLY 1 VOLTAGE IS TOO LOW
When Monitored and Set Condition: P1611-SENSOR SUPPLY 1 VOLTAGE IS TOO LOW When Monitored: With the ignition on.
Set Condition: The ECM detects a short to ground on the APP Sensor 5-volt Supply circuit or the CMP Sensor 5-volt Supply circuit.
POSSIBLE CAUSES APP SENSOR CMP SENSOR VISUAL WIRING AND CONNECTOR INSPECTION INTERMITTENT CONDITION SENSOR SUPPLY 1 SHORTED TO GROUND ACCEL PEDAL POSITION SENSOR 5-VOLT SUPPY CIRCUIT SHORT TO SENSOR GROUND CIRCUIT CAMSHAFT POSITION SENSOR 5-VOLT SUPPLY CIRCUIT SHORTED TO SENSOR GROUND CIRCUIT ENGINE CONTROL MODULE
TEST 1 ACTION NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. Turn the ignition on. With the DRB, erase ECM DTCs. Turn the ignition off for 10 seconds. Turn the ignition on. Monitor the DRB for ECM DTCs. Did this DTC set again? Yes No 2 Go To Go To 2 8 All APPLICABILITY All
Turn the ignition off. Visually inspect the wiring and connectors associated with the APP and CMP Sensors for problems that may result in a short circuit. Were any problems found? Yes No Repair or replace wiring/connectors as necessary. Perform ROAD TEST VERIFICATION - VER-2. Go To 3
96
P1611-SENSOR SUPPLY 1 VOLTAGE IS TOO LOW
TEST 3 ACTION Turn the ignition off. Disconnect the APP and CMP Sensor harness connectors. Disconnect the ECM harness connectors. Measure the resistance between ground and ECM harness connector cavities C1-38, C1-37, C2-13, C2-24 and C2-25. Is the voltage below 1000 ohms for any of the measurements? Yes Repair the circuit(s) that measured below 1000 ohms for a short to ground. Perform ROAD TEST VERIFICATION - VER-2. Go To 4 All
Continued
APPLICABILITY All
No 4
Turn the ignition off. Disconnect the Camshaft Position Sensor harness connector. Disconnect the ECM harness connectors. Measure the resistance between the Sensor Ground circuit and the CMP Sensor 5-volt Supply circuit at the CMP Sensor harness connector. Is the resistance above 1000 ohms? Yes No Go To 5
Repair the Camshaft Position Sensor 5-volt Supply circuit for a short to the Sensor Ground circuit. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Disconnect the APP Sensor harness connector. Disconnect the ECM harness connectors. Measure the resistance between the 5-volt Supply circuit and each of the Sensor Ground circuits at the APP Sensor harness connector. Is the resistance above 1000 ohms for both measurements? Yes No Go To 6
Repair the APP Sensor 5-volt Supply circuit for a short to the Sensor Ground circuit. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Disconnect the APP Sensor harness connector. Turn the ignition on. With the DRBIII , erase ECM DTCs. Turn the ignition off for 10 seconds. Turn the ignition on. With the DRBIII , read ECM DTCs. Does the DRB display this DTC? Yes No Go To 7
Replace the APP Sensor. Perform ROAD TEST VERIFICATION - VER-2.
97
TEST 7 ACTION Turn the ignition off. Disconnect the CMP Sensor harness connector. Turn the ignition on. With the DRBIII , erase ECM DTCs. Turn the ignition off for 10 seconds. Turn the ignition on. With the DRBIII , read ECM DTCs. Does the DRB display this DTC? Yes Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Replace the Camshaft Position Sensor. Perform ROAD TEST VERIFICATION - VER-2. All
Continued
APPLICABILITY All
No 8
98
Symptom: P1612-IGNITION VOLTAGE - VOLTAGE ERROR
POSSIBLE CAUSES CHECK THE ECM POWER AND GROUNDS ENGINE CONTROL MODULE INTERMITTENT CONDITION
TEST 1 ACTION Turn the ignition on. With the DRBIII , erase ECM DTCs. Perform several engine run cycles, turning the ignition off for at least 20 seconds between each engine run cycle. With the DRBIII , read the ECM DTCs. Did this DTC set again? Yes No 2 Go To Go To 2 3 All APPLICABILITY All
Refer to symptom Checking the ECM Power and Grounds. Are the ECM Power and Ground circuits o.k.? Yes No Replace the ECM in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Repair as necessary. Perform ROAD TEST VERIFICATION - VER-2.
All
99
Symptom List: P1615-ECM VOLTAGE SUPPLY IS TOO HIGH P1615-ECM VOLTAGE SUPPLY IS TOO LOW
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P1615-ECM VOLTAGE SUPPLY IS TOO HIGH.
When Monitored and Set Condition: P1615-ECM VOLTAGE SUPPLY IS TOO HIGH When Monitored: Set Condition: With the ignition on.
The ECM detects voltage above 16 volts on the Battery Supply circuit(s).
P1615-ECM VOLTAGE SUPPLY IS TOO LOW When Monitored: Set Condition: circuit(s). With the ignition on.
The ECM detects voltage below 8.0 volts on the ECM Battery Supply
POSSIBLE CAUSES CHECKING ECM POWER AND GROUNDS ECM INTERMITTENT CONDITION
TEST 1 ACTION NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. Turn the ignition on. With the DRB, erase ECM DTCs. NOTE: This DTC may be caused by a charging system problem. Refer to the Service Information and verify proper charging system operation before continuing. Test drive the vehicle. Turn the ignition on. With the DRB, read ECM DTCs. Did this DTC set again? Yes No Go To Go To 2 3 APPLICABILITY All
100
P1615-ECM VOLTAGE SUPPLY IS TOO HIGH
TEST 2 ACTION Refer to the symptom list and perform the Checking the ECM Power and Ground test. Were any problem found with the ECM powers and grounds? Yes No Repair as necessary. Perform ROAD TEST VERIFICATION - VER-2. Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. All
Continued
APPLICABILITY All
101
Symptom List: P1630-IMMOBILIZER P1630-IMMOBILIZER P1630-IMMOBILIZER P1630-IMMOBILIZER P2201-IMMOBILIZER CAN MESSAGE ERROR P2243-NO MESSAGE RECEIVED FROM SKREEM
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P1630-IMMOBILIZER.
POSSIBLE CAUSES CHECKING SKREEM DTCS OPEN CAN BUS CIRCUITS SKREEM MODULE INTERMITTENT CONDITION
Turn the ignition on. With the DRBIII , attempt to communicate with the SKREEM and read SKREEM DTCs. NOTE: If the DRB is unable to communicate with the SKREEM, refer to the appropriate test in the Communication category Are there any SKREEM DTCs? Yes No Repair SKREEM DTCs as necessary. Perform ROAD TEST VERIFICATION - VER-2. Go To 3
102
P1630-IMMOBILIZER
TEST 3
Continued
ACTION APPLICABILITY All
Turn the ignition off. Disconnect the SKREEM Module harness connector. Disconnect the ECM harness connectors. Measure the resistance of each CAN Bus circuit between the ECM harness connector and the SKREEM harness connector. Is the resistance below 10.0 ohms for each measurement? Yes Replace and program the SKREEM Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Repair the open CAN Bus circuit(s) between the ECM and the SKREEM. Perform ROAD TEST VERIFICATION - VER-2.
No
All
103
Symptom List: P1681-ACM CIRCUIT FAULT P1681-ACM CIRCUIT SHORT TO VOLTAGE
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P1681-ACM CIRCUIT FAULT.
POSSIBLE CAUSES AIRBAG CONTROL MODULE INTERMITTENT CONDITION ACM SIGNAL CIRCUIT SHORTED TO VOLTAGE ENGINE CONTROL MODULE
TEST 1 ACTION NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. With the DRB, check the Airbag Module for proper communication and DTCs. If there are any ACM DTCs, repair them prior to continuing this test. Turn the ignition on. With the DRB, erase ECM DTCs. Start the engine. With the DRB, read ECM DTCs. Did this DTC set again? Yes No 2 Go To Go To 2 4 All APPLICABILITY All
Turn the ignition off. Disconnect the ECM harness connectors. Remove the Engine Control Relay. Connect a jumper wire between cavity 30 and cavity 87 of the Engine Control Relay connector. Turn the ignition on. Measure the voltage of the ACM Signal circuit. Is the voltage below 1.0 volt? Yes Replace the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Go To 3
No
104
P1681-ACM CIRCUIT FAULT
TEST 3
Continued
APPLICABILITY All
ACTION Turn the ignition off. Refer to the Service Information and disconnect the ACM harness connector. Disconnect the ECM harness connectors. Remove the Engine Control Relay from the Fuse Block No.1 Connect a jumper wire between cavity 30 and cavity 87 of the Engine Control Relay connector in Fuse Block No.1. Turn the ignition on. Measure the voltage of the ACM Signal circuit. Is the voltage below 1.0 volt? Yes Replace and program the Airbag Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Repair the ACM Signal circuit for a short to voltage. Perform ROAD TEST VERIFICATION - VER-2.
No 4
All
105
Symptom List: P2009-WATER IN FUEL SENSOR - WATER IN FUEL P2009-WATER IN FUEL SENSOR SIGNAL ERROR
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P2009-WATER IN FUEL SENSOR - WATER IN FUEL.
POSSIBLE CAUSES 12-VOLT SUPPLY CIRCUIT OPEN CHECKING ECM POWER AND GROUNDS CHECKING THE ENGINE CONTROL RELAY SYSTEM ECM - WATER IN FUEL SENSOR SIGNAL CIRCUIT SHORTED TO VOLTAGE ECM - WATER IN FUEL SENSOR SIGNAL SHORT TO GROUND SENSOR GROUND CIRCUIT OPEN WATER IN FUEL SENSOR FAILURE WATER IN FUEL SENSOR SIGNAL CIRCUIT OPEN WATER IN FUEL SENSOR SIGNAL CIRCUIT SHORTED TO 12-VOLT SUPPLY WATER IN FUEL SENSOR SIGNAL CIRCUIT SHORTED TO GROUND WATER IN FUEL SENSOR SIGNAL CIRCUIT SHORTED TO SENSOR GROUND WATER IN FUEL SENSOR SIGNAL CIRCUIT SHORTED TO VOLTAGE INTERMITTENT CONDITION
TEST 1 ACTION NOTE: If DTC P1611, P2306 or P2332 is present with this DTC, diagnose DTCs P1611, P2306 or P2332 before diagnosing this DTC. NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. NOTE: If you are here due to a P2009 indicating Water In The Fuel Filter DTC, ensure that the fuel system is not contaminated with water or other fluids before continuing. NOTE: If the fuel system is contaminated, refer to the Service Information to remove fuel, clean system and refill with known good fuel. Turn the ignition on. With the DRB, erase ECM DTCs. Start the engine several times, letting the engine run for at least 30 seconds at a time. With the DRB, read ECM DTCs. Did this DTC set again? Yes No Go To Go To 2 11 106 APPLICABILITY All
P2009-WATER IN FUEL SENSOR - WATER IN FUEL
TEST 2 ACTION Turn the ignition off. Disconnect the ECM harness connectors. Connect a jumper wire between ground and the Engine Control Relay Control circuit in ECM C2 harness connector cavity 44. Turn the ignition on. Using a 12-volt test light connected to ground, check the Fused Engine Control Relay Output circuits at the ECM C2 harness connector cavities 1, 3 and 5. Choose the appropriate result. Test light is on for all circuits. Go To 3 Test light is on for 1 or 2 circuits Repair the Engine Control Relay Output circuit(s) that did not illuminate brightly for an open. Perform ROAD TEST VERIFICATION - VER-2. Light off for all circuits. Refer to symptom Checking the ECM Power and Grounds. Perform ROAD TEST VERIFICATION - VER-2. 3 Turn the ignition off. Disconnect the Water In Fuel Sensor harness connector. Turn the ignition on. Measure the voltage of the Water In Fuel Sensor Signal circuit. Select the appropriate voltage reading. Voltage is above 5.4 volts. Go To 4 Voltage is between 4.7 and 5.4 volts. Go To 6 Voltage is below 4.7 volts. Go To 8 4 Turn the ignition off. Disconnect the In Fuel Level Sensor harness connector. Disconnect the ECM harness connectors. Remove the Engine Control Relay. Connect a jumper wire between cavity 30 and cavity 87 of the Engine Control Relay connector. Turn the ignition on. Measure the voltage of the Water In Fuel Sensor Signal circuit. Is the voltage below 1.0 volt? Yes No Go To 5 All All
Continued
APPLICABILITY All
Repair the Water In Fuel Sensor Signal circuit for a short to voltage. Perform ROAD TEST VERIFICATION - VER-2.
107
TEST 5 ACTION Turn the ignition off. Disconnect the Water In Fuel Sensor harness connector. Disconnect the ECM harness connectors. Measure the resistance between the 12-volt supply circuit and the Water In Fuel Sensor Signal circuit. Is the resistance above 1000 ohms? Yes Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Repair the Water In Fuel Sensor Signal circuit for a short to the 12-volt Supply circuit. Perform ROAD TEST VERIFICATION - VER-2. All
Continued
APPLICABILITY All
No
Turn the ignition off. Disconnect the ECM harness connectors. Disconnect the Water In Fuel Sensor harness connector. Measure the resistance of the 12-Volt Supply circuit between the ECM harness connector and the Water In Fuel Sensor harness connector. Is the resistance below 10.0 ohms? Yes No Go To 7
Repair the 12-Volt Supply circuit for an open. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Disconnect the ECM harness connectors. Disconnect the Water In Fuel Sensor harness connector. Measure the resistance of the Sensor Ground circuit. Is the resistance below 10.0 ohms? Yes No Replace the Water In Fuel Sensor. Perform ROAD TEST VERIFICATION - VER-2. Repair the Sensor Ground circuit for an open. Perform ROAD TEST VERIFICATION - VER-2.
Turn the ignition off. Disconnect the ECM harness connectors. Disconnect the Water In Fuel Sensor harness connector. Measure the resistance of the Water In Fuel Sensor Signal circuit. Is the resistance below 10.0 ohms? Yes No Go To 9
All
Repair the Water In Fuel Sensor Signal circuit for an open. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Disconnect the ECM harness connectors. Disconnect the Water In Fuel Sensor harness connector. Measure the resistance between ground and the Water In Fuel Sensor Signal circuit. Is the resistance above 1000 ohms? Yes No Go To 10
Repair the Water In Fuel Sensor Signal circuit for a short to ground. Perform ROAD TEST VERIFICATION - VER-2.
108
TEST 10 ACTION Turn the ignition off. Disconnect the ECM harness connectors. Disconnect the Water In Fuel Sensor harness connector. Measure the resistance between Sensor Ground and the Water In Fuel Sensor Signal circuit. Is the resistance above 1000 ohms? Yes Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Repair the Water In Fuel Sensor Signal circuit for a short to the Sensor Ground circuit. Perform ROAD TEST VERIFICATION - VER-2. All
Continued
APPLICABILITY All
No
11
109
Symptom List: P2010-MASS AIR FLOW SENSOR NEGATIVE DEVIATION P2010-MASS AIR FLOW SENSOR POSITIVE DEVIATION P2068-MASS AIR FLOW SENSOR PLAUSIBILITY SIGNAL RATIO TOO LARGE P2068-MASS AIR FLOW SENSOR PLAUSIBILITY SIGNAL RATIO TOO SMALL
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P2010-MASS AIR FLOW SENSOR NEGATIVE DEVIATION.
When Monitored and Set Condition: P2010-MASS AIR FLOW SENSOR NEGATIVE DEVIATION When Monitored: Set Condition: With the ignition on.
P2010-MASS AIR FLOW SENSOR POSITIVE DEVIATION When Monitored: Set Condition: With the ignition on.
P2068-MASS AIR FLOW SENSOR PLAUSIBILITY SIGNAL RATIO TOO LARGE When Monitored: Set Condition: With the ignition on.
P2068-MASS AIR FLOW SENSOR PLAUSIBILITY SIGNAL RATIO TOO SMALL When Monitored: Set Condition: With the ignition on.
POSSIBLE CAUSES MASS AIRFLOW SENSOR INTERMITTENT CONDITION
110
P2010-MASS AIR FLOW SENSOR NEGATIVE DEVIATION
TEST 1 ACTION NOTE: Inspect the turbocharger inlet tube between the MAF Sensor and the turbocharger for damage, restriction or poor connection. Any of these conditions can cause a MAF Plausibility DTC. NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. Turn the ignition on. With the DRBIII , erase the ECM DTCs. Test drive the vehicle. With the DRBIII , read the ECM DTCs. Does the DRB III display a Mass Air Flow Sensor DTC? Yes No 2 Replace the MAF Sensor. Perform ROAD TEST VERIFICATION - VER-2. Go To 2 All
Continued
APPLICABILITY All
111
Symptom List: P2013-AMBIENT AIR TEMPERATURE SIGNAL VOLTAGE TOO HIGH P2013-AMBIENT AIR TEMPERATURE SIGNAL VOLTAGE TOO LOW
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P2013-AMBIENT AIR TEMPERATURE SIGNAL VOLTAGE TOO HIGH.
When Monitored and Set Condition: P2013-AMBIENT AIR TEMPERATURE SIGNAL VOLTAGE TOO HIGH When Monitored: Set Condition: With the ignition on.
The Ambient Air Temperature Sensor signal is above 4.82 volts.
P2013-AMBIENT AIR TEMPERATURE SIGNAL VOLTAGE TOO LOW When Monitored: Set Condition:
TEST 1
With the ignition on.

ACTION APPLICABILITY All
The Ambient Air Temperature Sensor signal is below 0.068 volt.
NOTE: The Ambient Air Temperature Sensor is hardwired to the Instrument Cluster NOTE: Refer to the Instrument Cluster Diagnostic Information for the related symptom(s). Test Complete. Yes Test Complete.
112
Symptom List: P2014-ENGINE P2014-ENGINE P2014-ENGINE P2014-ENGINE P2040-ENGINE P2040-ENGINE P2040-ENGINE P2041-ENGINE P2041-ENGINE P2041-ENGINE P2042-ENGINE P2061-ENGINE P2062-ENGINE P2062-ENGINE
OIL OIL OIL OIL OIL OIL OIL OIL OIL OIL OIL OIL OIL OIL
SENSOR SENSOR SENSOR SENSOR SENSOR SENSOR SENSOR SENSOR SENSOR SENSOR SENSOR SENSOR SENSOR SENSOR
OIL TEMPERATURE PLAUSIBILITY SIGNAL PLAUSIBILITY SIGNAL VOLTAGE IS TOO HIGH SIGNAL VOLTAGE IS TOO LOW CIRCUIT INVALID LEVEL CIRCUIT LEVEL OUT OF RANGE CIRCUIT LEVEL OUT OF RANGE POOR OIL QUALITY QUALITY MEASUREMENT ERROR QUALITY PLAUSIBILITY WATER CONTAMINATION OPEN CIRCUIT SIGNAL ERROR SYNCHRONIZATION ERROR
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P2014-ENGINE OIL SENSOR OIL TEMPERATURE PLAUSIBILITY.
POSSIBLE CAUSES 5-VOLT SUPPLY CIRCUIT OPEN ECM - ENGINE OIL SENSOR SIGNAL CIRCUIT SHORTED TO VOLTAGE ECM - ENGINE OIL SENSOR SIGNAL SHORT TO GROUND ENGINE OIL SENSOR FAILURE ENGINE OIL SENSOR SIGNAL CIRCUIT OPEN ENGINE OIL SENSOR SIGNAL CIRCUIT SHORTED TO GROUND ENGINE OIL SENSOR SIGNAL CIRCUIT SHORTED TO SENSOR GROUND ENGINE OIL SENSOR SIGNAL CIRCUIT SHORTED TO VOLTAGE SENSOR GROUND CIRCUIT OPEN ENGINE OIL CONTAMINATION INTERMITTENT CONDITION
113
P2014-ENGINE OIL SENSOR OIL TEMPERATURE PLAUSIBILITY
Continued
TEST 1 ACTION NOTE: If DTC P1611, P2306 or P2332 is present with this DTC, diagnose DTCs P1611, P2306 or P2332 before diagnosing this DTC. NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. NOTE: The engine oil must be at the proper level for this test to be valid. Refer to the Service Information and ensure the engine oil level is at the specified level. Turn the ignition on. With the DRB, erase ECM DTCs. Start the engine several times, letting the engine run for at least 30 seconds at a time. With the DRB, read ECM DTCs. Did this DTC set again? Yes No 2 Go To Go To 2 10 All APPLICABILITY All
WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING. Refer to any Technical Service Bulletins (TSB) that may apply. Turn the ignition off. NOTE: This DTC implies that the engine may be contaminated by water, engine coolant or other material due to a mechanical or service failures such as failed gaskets, seals, cracks or incorrectly installed components. Inspect the engine for conditions referred to in the above note. Were any of the above conditions present? Yes No Repair as necessary. Perform ROAD TEST VERIFICATION - VER-2. Go To 3
Turn the ignition off. Disconnect the Engine Oil Sensor harness connector. Turn the ignition on. Measure the voltage of the Engine Oil Sensor Signal circuit. Select the appropriate voltage reading. Voltage is above 5.4 volts. Go To 4 Voltage is between 4.7 and 5.4 volts. Go To 5 Voltage is below 4.7 volts. Go To 7
All
114
Continued
TEST 4 ACTION Turn the ignition off. Disconnect the Engine Oil Sensor harness connector. Disconnect the ECM harness connectors. Remove the Engine Control Relay. Connect a jumper wire between cavity 30 and cavity 87 of the Engine Control Relay connector. Turn the ignition on. Measure the voltage of the Engine Oil Sensor Signal circuit. Is the voltage below 1.0 volt? Yes Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Repair the Engine Oil Sensor Signal circuit for a short to voltage. Perform ROAD TEST VERIFICATION - VER-2. All APPLICABILITY All
No 5
Turn the ignition off. Disconnect the ECM harness connectors. Disconnect the Engine Oil Sensor harness connector. Measure the resistance of the 5-Volt Supply circuit between the ECM harness connector and the Engine Oil Sensor harness connector. Is the resistance below 10.0 ohms? Yes No Go To 6
Turn the ignition off. Disconnect the ECM harness connectors. Disconnect the Engine Oil Sensor harness connector. Measure the resistance of the Sensor Ground circuit. Is the resistance below 10.0 ohms? Yes No Replace the Engine Oil Sensor. Perform ROAD TEST VERIFICATION - VER-2. Repair the Sensor Ground circuit for an open. Perform ROAD TEST VERIFICATION - VER-2.
Turn the ignition off. Disconnect the ECM harness connectors. Disconnect the Engine Oil Sensor harness connector. Measure the resistance of the Engine Oil Sensor Signal circuit. Is the resistance below 10.0 ohms? Yes No Go To 8
All
Repair the Engine Oil Sensor Signal circuit for an open. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Disconnect the ECM harness connectors. Disconnect the Engine Oil Sensor harness connector. Measure the resistance between ground and the Engine Oil Sensor Signal circuit. Is the resistance above 1000 ohms? Yes No Go To 9
Repair the Engine Oil Sensor Signal circuit for a short to ground. Perform ROAD TEST VERIFICATION - VER-2.
115
Continued
TEST 9 ACTION Turn the ignition off. Disconnect the ECM harness connectors. Disconnect the Engine Oil Sensor harness connector. Measure the resistance between Sensor Ground and the Engine Oil Sensor Signal circuit. Is the resistance above 1000 ohms? Yes Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Repair the Engine Oil Sensor Signal circuit for a short to the Sensor Ground circuit. Perform ROAD TEST VERIFICATION - VER-2. All APPLICABILITY All
No
10
116
Symptom List: P2015-FUEL RAIL PRESSURE MALFUNCTION MAXIMUM FUEL FLOW EXCEEDED P2016-FUEL RAIL PRESSURE MALFUNCTION DECELERATION ERROR P2016-FUEL RAIL PRESSURE MALFUNCTION FUEL FLOW BELOW MINIMUM QUANTITY P2017-FUEL RAIL PRESSURE MALFUNCTION RAIL PRESSURE IS TOO LOW P2018-FUEL RAIL PRESSURE MALFUNCTION RAIL PRESSURE IS TOO HIGH P2019-FUEL RAIL PRESSURE MALFUNCTION MAXIMUM FUEL PRESSURE EXCEEDED P2019-FUEL RAIL PRESSURE MALFUNCTION RAIL PRESSURE IS TOO LOW P2020-FUEL RAIL PRESSURE MALFUNCTION RAIL PRESSURE IS TOO LOW P2020-FUEL RAIL PRESSURE MALFUNCTION RAIL PRESSURE TOO HIGH P2021-FUEL RAIL PRESSURE MALFUNCTION RAIL PRESSURE TOO LOW P2023-FUEL RAIL PRESSURE MALFUNCTION RAIL PRESSURE TOO HIGH P2047-FUEL RAIL PRESSURE MALFUNCTION MAXIMUM FUEL PRESSURE EXCEEDED P2049-FUEL RAIL PRESSURE MALFUNCTION DECELERATION ERROR P2051-FUEL RAIL PRESSURE MALFUNCTION MAXIMUM FUEL PRESSURE EXCEEDED P2052-FUEL RAIL PRESSURE MALFUNCTION PLAUSIBILITY WITH FUEL PRESSURE SOLENOID
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P2015-FUEL RAIL PRESSURE MALFUNCTION MAXIMUM FUEL FLOW EXCEEDED.
POSSIBLE CAUSES AIR IN FUEL SYSTEM CHECKING ELECTRICAL CIRCUITS-ENGINE RUNNING CHECKING ELECTRICAL CIRCUITS-NO START CHECKING FOR OTHER DTCS CHECKING THE FUEL DELIVERY SYSTEM
117
P2015-FUEL RAIL PRESSURE MALFUNCTION MAXIMUM FUEL FLOW EXCEEDED Continued
POSSIBLE CAUSES CHECKING THE FUEL DELIVERY SYSTEM CORRECTION QUANTITY CHECK CYLINDER SPEED CHECK FUEL INJECTION PUMP CHECK FUEL LEAK QUANTITY CHECK FUEL LEAK QUANTITY CHECK FUEL PRESSURE SOLENOID FUEL PRESSURE SOLENOID CHECK FUEL PRESSURE VARIATION CHECK FUEL PUMP FUEL QUANTITY SOLENOID FUEL SYSTEM CONTAMINATION FUEL SYSTEM LEAK INTERMITTENT CONDITION
TEST 1 ACTION WARNING: HIGH-PRESSURE FUEL LINES DELIVER DIESEL FUEL UNDER EXTREME PRESSURE FROM THE INJECTION PUMP TO THE FUEL INJECTORS. THIS MAY BE AS HIGH AS 23,200 PSI (1600 BAR). USE EXTREME CAUTION WHEN INSPECTING FOR HIGH-PRESSURE FUEL LEAKS. WARNING: FUEL UNDER THIS AMOUNT OF PRESSURE CAN PENETRATE SKIN CAUSING PERSONAL INJURY OR DEATH. INSPECT FOR HIGH-PRESSURE FUEL LEAKS WITH A SHEET OF CARDBOARD. WEAR SAFETY GOGGLES AND ADEQUATE PROTECTIVE CLOTHING WHEN SERVICING FUEL SYSTEM. Turn the ignition on. With the DRBIII , read the ECM DTCs. Are there any other DTCs present? Yes Refer to symptom list for problems related to the DTC other than this DTC. Perform ROAD TEST VERIFICATION - VER-2. Go To 2 All APPLICABILITY All
No 2
Turn the ignition on. With the DRBIII , erase the ECM DTCs. Attempt to start the engine. Does the engine start and idle? Yes No Go To Go To 3 17
118
TEST 3 ACTION Turn the ignition off. WARNING: HIGH-PRESSURE FUEL LINES DELIVER DIESEL FUEL UNDER EXTREME PRESSURE FROM THE INJECTION PUMP TO THE FUEL INJECTORS. THIS MAY BE AS HIGH AS 23,200 PSI (1600 BAR). USE EXTREME CAUTION WHEN INSPECTING FOR HIGH-PRESSURE FUEL LEAKS. WARNING: FUEL UNDER THIS AMOUNT OF PRESSURE CAN PENETRATE SKIN CAUSING PERSONAL INJURY OR DEATH. INSPECT FOR HIGH-PRESSURE FUEL LEAKS WITH A SHEET OF CARDBOARD. WEAR SAFETY GOGGLES AND ADEQUATE PROTECTIVE CLOTHING WHEN SERVICING FUEL SYSTEM. Inspect the entire fuel system for leakage. Is there any evidence of leakage? Yes No 4 Repair as necessary in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Go To 4 All APPLICABILITY All
NOTE: Mixing any other fuels such as gasoline or kerosine can cause this DTC to set. Turn the ignition off. WARNING: HIGH-PRESSURE FUEL LINES DELIVER DIESEL FUEL UNDER EXTREME PRESSURE FROM THE INJECTION PUMP TO THE FUEL INJECTORS. THIS MAY BE AS HIGH AS 23,200 PSI (1600 BAR). USE EXTREME CAUTION WHEN INSPECTING FOR HIGH-PRESSURE FUEL LEAKS. WARNING: FUEL UNDER THIS AMOUNT OF PRESSURE CAN PENETRATE SKIN CAUSING PERSONAL INJURY OR DEATH. INSPECT FOR HIGH-PRESSURE FUEL LEAKS WITH A SHEET OF CARDBOARD. WEAR SAFETY GOGGLES AND ADEQUATE PROTECTIVE CLOTHING WHEN SERVICING FUEL SYSTEM. Refer to the Service Information and inspect the fuel system for contamination. Is the fuel contaminated? Yes No Repair as necessary in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Go To 5
119
TEST 5 ACTION NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB III at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. NOTE: Refer to the Service Information and perform the Air Bleed Procedure before continuing diagnosis. Turn the ignition on. With the DRBIII , erase the ECM DTCs. Start and idle the engine while monitoring for ECM DTCs. If the DTC does not reset at idle condition, test drive the vehicle under various load and speed conditions to attempt to duplicate the fault. NOTE: Driving the vehicle up and down steep hills or rapid cornering with a low fuel level can cause this DTC to set. Verify with customer if Low Fuel Light was illuminated when fault occurred. With the DRBIII , read the ECM DTCs. Does the DRBIII display this DTC? Yes No 6 Go To Go To 6 16 All APPLICABILITY All
Start the engine. With the DRBIII in Sensors, compare the Fuel Pressure Setpoint with the Actual Fuel Pressure readings. NOTE: If there is air in the fuel system, the Actual Fuel Pressure will oscillate above and below the Fuel Pressure Setpoint. Does Actual Fuel Pressure oscillate above and below the Fuel Pressure Setpoint? Yes No Refer to the Service Information to purge air from the fuel system. Perform ROAD TEST VERIFICATION - VER-2. Go To 7
Start the engine. With the DRBIII in Sensors, compare the Fuel Pressure Setpoint with the Actual Fuel Pressure readings. NOTE: A sticking Fuel Pressure Solenoid is indicated by Actual Fuel Pressure gradually dropping below the Fuel Pressure Setpoint then suddenly increasing (spiking) above the Fuel Pressure Setpoint. Does Actual Fuel Pressure gradually decrease then suddenly increase (spike) above the Fuel Pressure Yes Replace the Fuel Pressure Solenoid in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Go To 8
All
No
120
TEST 8 ACTION Refer to the appropriate Service Information and refer to Diagnosis and Testing Fuel Delivery System table. NOTE: The following is a list of problems that can cause fuel pressure to deviate from specification: restricted fuel filter or fuel lines, failed fuel pressure solenoid, failed fuel lift pump, failed fuel sending unit, contaminated fuel, faulty injector. Were there any problems with the Fuel Delivery System? Yes No 9 Repair as necessary in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Go To 9 All APPLICABILITY All
Refer to each of the following symptoms in the Driveability category. CHECKING THE FUEL PRESSURE SOLENOID CIRCUITS CHECKING THE FUEL QUANTITY SOLENOID CIRCUITS CHECKING THE FUEL PRESSURE SENSOR CIRCUITS Were any problems found? Yes No Repair as necessary. Perform ROAD TEST VERIFICATION - VER-2. Go To 10
10
NOTE: An injector that sticks open can cause this DTC. A sticking injector will cause the engine to misfire and emit excessive black smoke from the exhaust system. Refer to the Service Information and perform the Fuel Injector Leak Quantity Test. Were any problems found? Yes Using the Service Information, remove and inspect the Fuel Injectors for signs of damage or debris that may cause the injector to stick. Sticking injectors may cause the combustion chamber to become black and oil soaked. Replace Injector(s) as necessary. Perform ROAD TEST VERIFICATION - VER-2. Go To 11
All
No 11
With the DRBIII , select System Test, Smooth Eng Run Check, then Correction Quantity Check. Perform this test at Idle, 2000 rpm and 3000 rpm. NOTE: Readings per cylinder should be below 0.00450 mm3/stroke for each cylinder at each engine speed. Did any of the cylinders exceed 0.00450 mm3/stroke during this test? Yes Replace Fuel Injector of the cylinder(s) that had readings above 0.00450 mm3/stroke. Perform ROAD TEST VERIFICATION - VER-2. Go To 12
All
No 12
With the DRBIII , select System Test, Smooth Eng Run Check, then Cylinder Speed Check. NOTE: Readings for all cylinders should be close to each other. Look for one or two cylinders to differ high or low from the other cylinders. Did any of the cylinders differ significantly from the majority of the other cylinders? Yes Replace Fuel Injector of the cylinder(s) that had readings significantly above or below the other fuel injectors. Perform ROAD TEST VERIFICATION - VER-2. Go To 13
All
No
121
TEST 13 ACTION With the DRBIII , select System Tests, then perform the Rail Press Control Valve Test. Did this test pass? Yes No Go To 14 APPLICABILITY All
Replace the Fuel Pressure Solenoid in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. All
14
With the DRBIII , select System Tests, then perform the Rail Press Control Valve Variation Test. Did this test pass? Yes No Go To 15
Replace the Fuel Pressure Solenoid in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. All
15
With the DRBIII , select System Test, then High Pressure Pump. NOTE: During this test engine speed is set at 1,400 rpm and initial fuel pressure at approximately 6,800 psi. During the test fuel pressure is instantly set to above 20,000 psi. to test the performance of the Fuel Injection Pump. NOTE: After the test is completed, the DRB display fuel pressure in 30 counter steps. If the fuel pressure increases from approximately 6,800 psi to above 20,000 psi in one counter step, the injection pump passes the test. Did the fuel pressure increase to above 20,000 psi within one counter step on the DRB? Yes Replace the Fuel Quantity Solenoid in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Replace Fuel Injection Pump in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2.
No
16
WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING. NOTE: The conditions that set the DTC are not present at this time. The following list may help in identifying the intermittent condition. With the engine running and at normal operating temperature, monitor the DRB III parameters related to the DTC while wiggling the wiring harness. Look for parameter values to change and/or a DTC to set. Review the DTC When Monitored and Set Conditions. If possible, try to duplicate the conditions under which the DTC was set. Refer to any Technical Service Bulletins (TSB) that may apply. Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or partially broken wires. Visually inspect the related wiring harness connectors. Look for broken, bent, pushed out, or corroded terminals. Were any of the above conditions present? Yes No Repair as necessary. Perform ROAD TEST VERIFICATION - VER-2. Test Complete.
All
122
TEST 17 ACTION Refer to the appropriate Service Information and refer to Diagnosis and Testing Fuel Delivery System table. NOTE: The following is a list of problems that can cause fuel pressure to deviate from specification: restricted fuel filter or fuel lines, failed fuel pressure solenoid, air in fuel system, failed fuel sending unit, contaminated fuel, faulty injector. Were there any problems with the Fuel Delivery System? Yes No 18 Repair as necessary in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Go To 18 All APPLICABILITY All
Refer to each of the following symptoms in the Driveability category. CHECKING THE FUEL PRESSURE SOLENOID CIRCUITS CHECKING THE FUEL QUANTITY SOLENOID CIRCUITS CHECKING THE FUEL PRESSURE SENSOR CIRCUITS Were any problems found? Yes No Repair as necessary. Perform ROAD TEST VERIFICATION - VER-2. Go To 19
19
NOTE: An injector that sticks open can cause this DTC. A sticking injector will cause the engine to misfire and emit excessive black smoke from the exhaust system. Refer to the Service Information and perform the Fuel Injector Leak Quantity during engine cranking test. Were any problems found? Yes Using the Service Information, remove and inspect the Fuel Injectors for signs of damage or debris that may cause the injector to stick. Sticking injectors may cause the combustion chamber to become black and oil soaked. Replace Injector(s) as necessary. Perform ROAD TEST VERIFICATION - VER-2. Go To 20
All
No 20
Turn the ignition off. Replace the Fuel Pressure Solenoid in accordance with the Service Information. Turn the ignition on. With the DRBIII , erase the ECM DTCs. Attempt to start and test drive the vehicle. With the DRBIII , read the ECM DTCs. Did this DTC set again? Yes No Go To 21
All
Test Complete.
123
TEST 21 ACTION Turn the ignition off. Replace the Fuel Quantity Solenoid in accordance with the Service Information. Turn the ignition on. With the DRBIII , erase the ECM DTCs. Attempt to start and test drive the vehicle. With the DRBIII , read the ECM DTCs. Did this DTC set again? Yes Replace the Fuel Pump in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Test Complete. APPLICABILITY All
No
124
Symptom: P2025-INTAKE PRESSURE SENSOR PLAUSIBILITY
When Monitored and Set Condition: P2025-INTAKE PRESSURE SENSOR PLAUSIBILITY When Monitored: With the ignition on.
Set Condition: The Intake Pressure Sensor signal does not agree with the Atmospheric Pressure Sensor signal in the ECM.
POSSIBLE CAUSES AIR FILTER AIR RESTRICTION INTERMITTENT CONDITION HIGH RESISTANCE IN THE INTAKE PRESSURE SENSOR SIGNAL CIRCUIT HIGH RESISTANCE IN THE INTAKE PRESSURE SENSOR GROUND CIRCUIT HIGH RESISTANCE IN THE INTAKE PRESSURE SENSOR 5-VOLT SUPPLY CIRCUIT ENGINE CONTROL MODULE
TEST 1 ACTION NOTE: If DTC P1611, P2306 or P2332 is present with this DTC, diagnose DTCs P1611, P2306 or P2332 before diagnosing this DTC. NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. Turn the ignition on. With the DRB, erase ECM DTCs. Turn the ignition off, wait 30 seconds. Test drive the vehicle. With the DRB, read ECM DTCs. Did this DTC set again? Yes No 2 Go To Go To 2 7 All APPLICABILITY All
125
P2025-INTAKE PRESSURE SENSOR PLAUSIBILITY
TEST 3 ACTION NOTE: Inspect all air intake and turbocharger related tubes for damage, restriction or poor connection. Any of these conditions can cause a this DTC to set. Turn the ignition off. Inspect all air intake and turbocharger related tubes and connections. were any problems found? Yes No 4 Repair or replace as necessary. Perform ROAD TEST VERIFICATION - VER-2. Go To 4 All
Continued
APPLICABILITY All
Repair the Intake Pressure Sensor Signal circuit for high resistance. Perform ROAD TEST VERIFICATION - VER-2. All
Repair the Intake Pressure Sensor Ground circuit for high resistance. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Disconnect the Intake Pressure Sensor harness connector. Disconnect the ECM harness connectors. Measure the resistance of the Intake Pressure Sensor 5-volt Supply circuit. Is the resistance below 10.0 ohms? Yes Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Repair the Intake Pressure Sensor 5 Volt Supply circuit for high resistance. Perform ROAD TEST VERIFICATION - VER-2.
No
126
P2025-INTAKE PRESSURE SENSOR PLAUSIBILITY
Continued
APPLICABILITY All
127
Symptom List: P2025-INTAKE P2030-INTAKE P2030-INTAKE P2030-INTAKE
PRESSURE SENSOR SIGNAL VOLTAGE TOO HIGH PRESSURE SENSOR CIRCUIT FAULT PRESSURE SENSOR OPEN CIRCUIT PRESSURE SENSOR SIGNAL VOLTAGE TOO HIGH
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P2025-INTAKE PRESSURE SENSOR SIGNAL VOLTAGE TOO HIGH.
POSSIBLE CAUSES INTERMITTENT CONDITION INTAKE PRESSURE SENSOR GROUND CIRCUIT SHORTED TO VOLTAGE INTAKE PRESSURE SENSOR SIGNAL CIRCUIT SHORTED TO VOLTAGE INTAKE PRESSURE SENSOR GROUND CIRCUIT OPEN INTAKE PRESSURE SENSOR ENGINE CONTROL MODULE (INTERNAL) ENGINE CONTROL MODULE (SENSOR SIGNAL SHORTED TO VOLTAGE)
TEST 1 ACTION NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. NOTE: Ensure all turbocharger inlet and outlet tubes are connected properly, without damage and restriction before continuing with this test. Also ensure the Boost Pressure Servo Motor and Servo Motor rod are attached and functioning properly. Turn the ignition on. With the DRB, erase ECM DTCs. Cycle the ignition key on and off several times, leaving the key on for at least 10 seconds at a time. With the DRB, read ECM DTCs. Did this DTC set again? Yes No Go To Go To 2 7 APPLICABILITY All
128
Continued
TEST 2 ACTION Turn the ignition off. Disconnect the Intake Pressure Sensor harness connector. Disconnect the ECM harness connectors. Turn the ignition on. Measure the voltage between ground and the Intake Pressure Sensor Signal circuit. Is the voltage above 1.0 volt? Yes No 3 Go To Go To 3 4 All APPLICABILITY All
Turn the ignition off. Disconnect the Intake Pressure Sensor harness connector. Disconnect the ECM harness connectors. Remove the Engine Control Relay. Connect a jumper wire between cavity 30 and cavity 87 of the Engine Control Relay connector. Turn the ignition on. Measure the voltage between ground and the Intake Pressure Sensor Signal circuit. Is the voltage above 1.0 volt? Yes Repair the Intake Pressure Sensor Signal circuit for a short to voltage. Perform ROAD TEST VERIFICATION - VER-2. Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2.
No
Turn the ignition off. Disconnect the Intake Pressure Sensor harness connector. Disconnect the ECM harness connectors. Remove the Engine Control Relay. Connect a jumper wire between cavity 30 and cavity 87 of the Engine Control Relay connector. Turn the ignition on. Measure the voltage between ground and the Intake Pressure Sensor Ground circuit. Is the voltage above 1.0 volt? Yes Repair the Intake Pressure Sensor Ground circuit for a short to voltage. Note: The ECM will need to be checked for proper operation before the repair is completed. A short to voltage on a ground circuit can damage the ECM. Perform ROAD TEST VERIFICATION - VER-2. Go To 5
All
No 5
All
Repair the Intake Pressure Sensor Ground circuit for an open. Perform ROAD TEST VERIFICATION - VER-2.
129
Continued
TEST 6 ACTION Turn the ignition off. NOTE: Ensure all harness connectors are connected. Turn the ignition on. Measure the voltage of the Intake Pressure Sensor Signal circuit by back probing ECM harness connector. Is the voltage above 4.85 volts? Yes No Replace the Intake Pressure Sensor. Perform ROAD TEST VERIFICATION - VER-2. Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. All APPLICABILITY All
130
Symptom List: P2025-INTAKE PRESSURE SENSOR SIGNAL VOLTAGE TOO LOW P2030-INTAKE PRESSURE SENSOR SIGNAL VOLTAGE TOO LOW
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P2025-INTAKE PRESSURE SENSOR SIGNAL VOLTAGE TOO LOW.
POSSIBLE CAUSES INTERMITTENT CONDITION INTAKE PRESSURE SENSOR 5 VOLT SUPPLY INTAKE PRESSURE SENSOR INTAKE PRESSURE SENSOR SIGNAL CIRCUIT SHORTED TO GROUND INTAKE PRESSURE SENSOR SIGNAL AND GROUND CIRCUITS SHORTED TOGETHER ENGINE CONTROL MODULE INTAKE PRESSURE SENSOR SIGNAL CIRCUIT OPEN
TEST 1 ACTION NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. NOTE: Ensure all turbocharger inlet and outlet tubes are connected properly, without damage and restriction before continuing with this test. Also ensure the Boost Pressure Servo Motor and Servo Motor rod are attached and functioning properly. Turn the ignition on. With the DRB, erase ECM DTCs. Cycle the ignition key on and off several times, leaving the key on for at least 10 seconds at a time. With the DRB, read ECM DTCs. Did this DTC set again? Yes No 2 Go To Go To 2 7 All APPLICABILITY All
Turn the ignition off. Disconnect the Intake Pressure Sensor harness connector. Turn the ignition on. Measure the voltage between ground and the Intake Pressure Sensor 5 Volt Supply circuit. Is the voltage above 4.8 volts? Yes No Go To 3
Repair the Intake Pressure Sensor 5 Volt Supply circuit for an open. Perform ROAD TEST VERIFICATION - VER-2.
131
Continued
TEST 3 ACTION Turn the ignition off. Disconnect the Intake Pressure Sensor harness connector. Disconnect the ECM harness connectors. Measure the resistance of the Intake Pressure Sensor Signal circuit. Is the resistance below 10.0 ohms? Yes No 4 Go To 4 APPLICABILITY All
Repair the Intake Pressure Sensor Signal circuit for an open. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Disconnect the Intake Pressure Sensor harness connector. Disconnect the ECM harness connectors. Measure the resistance between the Intake Pressure Sensor Signal circuit and Sensor Ground circuit. Is the resistance above 1000 ohms? Yes No Go To 5
Repair the Intake Pressure Sensor Signal circuit for a short to the Sensor Ground circuit. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Disconnect the Intake Pressure Sensor harness connector. Disconnect the ECM harness connectors. Measure the resistance between ground and the Intake Pressure Sensor Signal circuit. Is the resistance above 1000 ohms? Yes No Go To 6
Repair the Intake Pressure Sensor Signal circuit for a short to ground. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Disconnect the Intake Pressure Sensor harness connector. Turn the ignition on. Connect a jumper wire between the Intake Pressure Sensor Signal and Intake Pressure Sensor 5 Volt Supply circuits. With the DRB, read the Intake Pressure Sensor voltage. Is the voltage above 4.5 volts? Yes No Replace the Intake Pressure Sensor. Perform ROAD TEST VERIFICATION - VER-2. Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2.
132
Continued
133
Symptom List: P2026-O2 SENSOR CIRCUIT FAULT P2026-O2 SENSOR CIRCUIT OPEN CIRCUIT P2026-O2 SENSOR CIRCUIT SIGNAL VOLTAGE TOO HIGH P2026-O2 SENSOR CIRCUIT SIGNAL VOLTAGE TOO LOW P2028-O2 SENSOR CIRCUIT FAULT P2028-O2 SENSOR CIRCUIT OPEN CIRCUIT P2028-O2 SENSOR CIRCUIT SIGNAL VOLTAGE TOO HIGH P2028-O2 SENSOR CIRCUIT SIGNAL VOLTAGE TOO LOW P2032-O2 SENSOR PLAUSIBILITY P2032-O2 SENSOR PLAUSIBILITY P2032-O2 SENSOR PLAUSIBILITY P2057-O2 SENSOR SIGNAL CIRCUIT SIGNAL VOLTAGE TOO HIGH P2058-O2 SENSOR SIGNAL CIRCUIT SIGNAL VOLTAGE TOO HIGH P2059-O2 SENSOR SIGNAL CIRCUIT SIGNAL VOLTAGE TOO HIGH P2090-O2 SENSOR PLAUSIBILITY P2090-O2 SENSOR SIGNAL FAULT P2091-O2 SENSOR LOW O2 CONCENTRATION P2091-O2 SENSOR SIGNAL PLAUSIBILITY P2195-O2 SENSOR HEATER CIRCUIT FAULT P2353-O2 SENSOR PLAUSIBILITY P2366-O2 CIRCUIT FAULT
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P2026-O2 SENSOR CIRCUIT FAULT.
POSSIBLE CAUSES CHECKING CIRCUIT INTEGRITY ECM O2 SENSOR O2 SENSOR CIRCUIT SHORT TO GROUND O2 SENSOR CIRCUIT SHORT TO VOLTAGE O2 SENSOR CIRCUIT SHORT TOGETHER O2 SENSOR OPEN CIRCUIT POWER SUPPLY OPEN INTERMITTENT CONDITION
134
P2026-O2 SENSOR CIRCUIT FAULT
TEST 1 ACTION NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. Turn the ignition on. With the DRB, erase ECM DTCs. Turn the ignition off for 10 seconds. Test drive the vehicle. Monitor the DRB for ECM DTCs. Did this DTC set again? Yes No 2 Go To Go To 2 9 All
Continued
APPLICABILITY All
Turn the ignition off. Using the Service Information wiring diagrams, inspect the wiring and connectors between the ECM and the O2 sensor for damage, corrosion, poor terminal contact or other problems. Were any problems found? Yes No Clean, repair or replace as necessary. Perform ROAD TEST VERIFICATION - VER-2. Go To 3
Turn the ignition off. Disconnect the O2 Sensor harness connector. Turn the ignition on. Using a 12-volt test light connected to ground, check the Power Supply circuit at the O2 harness connector cavity 4. Does the test light illuminate brightly? Yes No Go To 4
All
Repair the Power Supply circuit for an open or short to ground. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Disconnect the O2 Sensor harness connector. Disconnect the ECM harness connectors. Perform the following resistance measurements from the O2 harness connector to the ECM harness connector. O2 Sensor Cavity 1 to ECM Cavity C1-15. O2 Sensor Cavity 2 to ECM Cavity C1-40. O2 Sensor Cavity 3 to ECM Cavity C1-72. O2 Sensor Cavity 5 to ECM Cavity C1-62. O2 Sensor Cavity 6 to ECM Cavity C1-39. Is the resistance below 10.0 ohms for each measurement? Yes No Go To 5
Repair the circuit(s) that measured above 10.0 ohms for an open. Perform ROAD TEST VERIFICATION - VER-2.
135
TEST 5 ACTION Turn the ignition off. Disconnect the O2 Sensor harness connector. Disconnect the ECM harness connectors. Measure the resistance between ground and O2 Sensor harness connector cavities 1, 2, 3, 5, and 6. Is the resistance above 1000 ohms for each measurement? Yes No Go To 6
Continued
APPLICABILITY All
Repair the circuit(s) that measured below 1000 ohms for a short to ground. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Disconnect the O2 Sensor harness connector. Disconnect the ECM harness connectors. NOTE: The circuits connecting the O2 Sensor and the ECM are single circuits and do not contain any splices. There should be NO continuity from one circuit to the other. Using an ohmmeter, check the O2 Sensor circuits for shorts together (resistance below 1000 ohms).. Is the resistance from any O2 Sensor circuit to another below 1000 ohms? Yes Repair the circuits that measured below 1000 ohms for a short together. Perform ROAD TEST VERIFICATION - VER-2. Go To 7
No 7
Turn the ignition off. Disconnect the O2 Sensor harness connector. Disconnect the ECM harness connectors. Remove the Engine Control Relay. Connect a jumper wire between cavity 30 and cavity 87 of the Engine Control Relay connector. Turn the ignition on. Measure the voltage of O2 Sensor harness connector cavities 1, 2, 3, 5, and 6. Is the voltage below 1.0 volts for each measurement? Yes No Go To 8
All
Repair the circuit(s) that measured below 1000 ohms for a short to voltage. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Replace the O2 Sensor in accordance with the Service Information. Turn the ignition on. With the DRBIII , erase the ECM DTCs. Test drive the vehicle. With the DRBIII , read the ECM DTCs. Did this DTC set again? Yes No Replace the ECM in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Test Complete.
136
Continued
APPLICABILITY All
137
Symptom List: P2034-O2 P2034-O2 P2036-O2 P2036-O2 P2038-O2 P2038-O2
SENSOR SENSOR SENSOR SENSOR SENSOR SENSOR
CIRCUIT CIRCUIT CIRCUIT CIRCUIT CIRCUIT CIRCUIT
CALIBRATION CALIBRATION CALIBRATION CALIBRATION CALIBRATION CALIBRATION
VALUE VALUE VALUE VALUE VALUE VALUE
TOO TOO TOO TOO TOO TOO
HIGH LOW HIGH LOW HIGH LOW
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P2034-O2 SENSOR CIRCUIT CALIBRATION VALUE TOO HIGH.
POSSIBLE CAUSES CHECKING CIRCUIT INTEGRITY O2 SENSOR INTERMITTENT CONDITION

TEST 1 ACTION Turn the ignition off. Using the Service Information wiring diagrams, inspect the wiring and connectors between the ECM and the O2 sensor for damage, corrosion, poor terminal contact or other problems. Were any problems found? Yes No 2 Clean, repair or replace as necessary. Perform ROAD TEST VERIFICATION - VER-2. Go To 2 All APPLICABILITY All
NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. Turn the ignition on. With the DRB, erase ECM DTCs. Turn the ignition off for 10 seconds. Test drive the vehicle. Monitor the DRB for ECM DTCs. Did this DTC set again? Yes No Replace the Oxygen Sensor. Perform ROAD TEST VERIFICATION - VER-2. Go To 3
138
P2034-O2 SENSOR CIRCUIT CALIBRATION VALUE TOO HIGH
Continued
139
Symptom List: P2043-CAMSHAFT POSITION SENSOR CIRCUIT OPEN CIRCUIT P2043-CAMSHAFT POSITION SENSOR CIRCUIT OPEN OR SHORT CIRCUIT
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P2043-CAMSHAFT POSITION SENSOR CIRCUIT OPEN CIRCUIT.
POSSIBLE CAUSES 5-VOLT SUPPLY CIRCUIT OPEN CAMSHAFT POSITION SENSOR SIGNAL CIRCUIT SHORTED TO VOLTAGE CHECKING 5-VOLT SUPPLY CIRCUIT DAMAGED CMP SENSOR OR CAMSHAFT ECM ECM ECM - CAMSHAFT POSITION SENSOR SIGNAL CIRCUIT SHORTED TO VOLTAGE SENSOR GROUND CIRCUIT OPEN INTERMITTENT CONDITION CMP SENSOR SIGNAL CIRCUIT OPEN 5-VOLT SUPPLY CIRCUIT SHORTED TO GROUND CMP SENSOR SIGNAL CIRCUIT SHORTED TO GROUND CMASHAFT POSITION SENSOR ECM SENSOR GROUND CIRCUIT OPEN 5-VOLT SUPPLY CIRCUIT SHORTED TO THE SENSOR GROUND CIRCUIT CMP SENSOR SIGNAL CIRCUIT SHORTED TO THE SENSOR GROUND CIRCUIT
140
P2043-CAMSHAFT POSITION SENSOR CIRCUIT OPEN CIRCUIT
Continued
TEST 1 ACTION NOTE: If DTC P1611, P2306 or P2332 is present with this DTC, diagnose DTCs P1611, P2306 or P2332 before diagnosing this DTC. NOTE: The Timing Belt/Chain must be correctly installed and operational before diagnosis can be made. Refer to the Service Information to ensure the timing belt is properly installed. NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. Turn the ignition on. With the DRBIII , erase the ECM DTCs. Attempt to start the engine cranking the engine for at least 7 seconds. With the DRBIII , read the ECM DTCs. Does the DRBIII display this DTC? Yes No 2 Go To Go To 4 2 All APPLICABILITY All
Turn the ignition on. With the DRBIII , erase the ECM DTCs. Test drive the vehicle. With the DRBIII , read the ECM DTCs. Does the DRBIII display this DTC? Yes No Go To Go To 3 16
Turn the ignition off. Disconnect the Camshaft Position Sensor harness connector. Turn the ignition on. Measure the voltage of the CMP Sensor Signal circuit. Select the appropriate voltage reading. Voltage is above 5.4 volts. Go To 4 Voltage is between 4.7 and 5.4 volts. Go To 5 Voltage is below 4.7 volts. Go To 13
All
141
Continued
TEST 4 ACTION Turn the ignition off. Disconnect the Camshaft Position Sensor harness connector. Disconnect the ECM harness connectors. Remove the Engine Control Relay. Connect a jumper wire between cavity 30 and cavity 87 of the Engine Control Relay connector. Turn the ignition on. Measure the voltage of the CMP Position Sensor Signal circuit. Is the voltage below 1.0 volt? Yes Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Repair the Camshaft Position Sensor Signal circuit for a short to voltage. Perform ROAD TEST VERIFICATION - VER-2. All APPLICABILITY All
No
Turn the ignition off. Disconnect the Camshaft Position Sensor harness connector. Turn the ignition on. Measure the voltage of the CMP Sensor 5-Volt Supply circuit. Select the appropriate voltage reading. Voltage is above 5.4 volts. Repair the CMP 5-Volt Supply circuit for a short to voltage. Perform ROAD TEST VERIFICATION - VER-2. Voltage is between 4.7 and 5.4 volts. Go To 6 Voltage is below 4.7 volts. Go To 10
Turn the ignition off. Disconnect the CMP Sensor harness connector. Disconnect the ECM harness connectors. Measure the resistance of the Sensor Ground circuit between the CMP Sensor harness connector and the ECM harness connector. Is the resistance below 10.0 ohms? Yes No Go To 7
All
Repair the Sensor Ground circuit for an open. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition on. Disconnect the ECT Sensor harness connector. Disconnect the Camshaft Position Sensor harness connector. Connect one end of a jumper wire to the ECT Sensor signal circuit in the ECT Sensor harness connector. Connect the other end of the jumper wire to the Sensor Ground circuit in the Camshaft Position Sensor harness connector. With the DRBIII in Engine, Sensors, read the Engine Coolant Temp volts. Is the voltage below 0.5 volt? Yes No Go To 8
Replace and program the ECM in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2.
142
Continued
TEST 8 ACTION Turn the ignition off. Remove the CMP Sensor. Inspect the CMP Sensor for conditions such as loose mounting screws, damage, or cracks. Inspect the camshaft for conditions such as damage, debris or cracked teeth. Is there any evidence of these conditions? Yes No 9 Repair as necessary. Perform ROAD TEST VERIFICATION - VER-2. Go To 9 All APPLICABILITY All
Turn the ignition off. With the DRBIII lab scope lead, backprobe the CMP Signal circuit. Set the DRBIII lab scope settings as follows: Time = 0.2s/Div, 20 volts scale, Offset = 0.00 volts, Probe = X10, Coupling = DC. While observing the DRBIII display, crank the engine. NOTE: The DRBIII should display a digital signal (square wave) similar to that shown in Charts and Graphs. Does the DRBIII display an uninterrupted digital signal (square wave)? Yes Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Replace the Camshaft Position Sensor in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2.
No
10
Turn the ignition off. Disconnect the ECM harness connectors. Disconnect the CMP Sensor harness connector. Measure the resistance of the 5-Volt Supply circuit between the ECM harness connector and the CMP Sensor harness connector. Is the resistance below 10.0 ohms? Yes No Go To 11
All
11
Turn the ignition off. Disconnect the CMP Sensor harness connector. Disconnect the ECM harness connectors. Measure the resistance between ground and the CMP Sensor 5-Volt Supply circuit. Is the resistance above 1000 ohms? Yes No Go To 12
Repair the CMP Sensor 5-Volt Supply circuit for a short to ground. Perform ROAD TEST VERIFICATION - VER-2.
143
Continued
TEST 12 ACTION Turn the ignition off. Disconnect the CMP Sensor harness connector. Disconnect the ECM harness connectors. Measure the resistance between the CMP Sensor 5-Volt Supply circuit and the Sensor Ground circuit at the CMP Sensor harness connector. Is the resistance above 1000 ohms? Yes Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Repair the CMP Sensor 5-Volt Supply and Sensor Ground circuits for a short together. Perform ROAD TEST VERIFICATION - VER-2. All APPLICABILITY All
No
13
Turn the ignition off. Disconnect the CMP Sensor harness connector. Disconnect the ECM harness connectors. Measure the resistance of the CMP Sensor Signal circuit. Is the resistance below 10.0 ohms? Yes No Go To 14
Repair the CMP Sensor Signal circuit for an open Perform ROAD TEST VERIFICATION - VER-2. All
14
Turn the ignition off. Disconnect the CMP Sensor harness connector. Disconnect the ECM harness connectors. Measure the resistance between ground and the CMP Sensor Signal circuit. Is the resistance below 1000 ohms? Yes No Repair the CMP Sensor Signal circuit for a short to ground. Perform ROAD TEST VERIFICATION - VER-2. Go To 15
15
Turn the ignition off. Disconnect the CMP Sensor harness connector. Disconnect the ECM harness connectors. Measure the resistance between the CMP Sensor Signal circuit and the Sensor Ground circuit at the CMP Sensor harness connector. Is the resistance below 1000 ohms? Yes Repair the CMP Sensor Signal and Sensor Ground circuits for a short together. Perform ROAD TEST VERIFICATION - VER-2. Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2.
All
No
144
Continued
TEST 16 ACTION WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING. NOTE: The conditions that set the DTC are not present at this time. The following list may help in identifying the intermittent condition. With the engine running and at normal operating temperature, monitor the DRB parameters related to the DTC while wiggling the wiring harness. Look for parameter values to change and/or a DTC to set. Remove the CMP Sensor and the CKP Sensor, checking for loose mounting screws and debris on the sensor magnets that can corrupt the sensor signal. Refer to any Technical Service Bulletins (TSB) that may apply. Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or partially broken wires. Visually inspect the related wiring harness connectors. Look for broken, bent, pushed out, or corroded terminals. Were any of the above conditions present? Yes No Repair as necessary. Perform ROAD TEST VERIFICATION - VER-2. Test Complete. APPLICABILITY All
145
Symptom List: P2045-CRANKSHAFT POSITION SENSOR CIRCUIT LOST SIGNAL P2045-CRANKSHAFT POSITION SENSOR CIRCUIT SIGNAL PLAUSIBILITY P2322-CRANKSHAFT POSITION SENSOR PLAUSIBILITY P2343-CKP PLAUSIBILITY
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P2045-CRANKSHAFT POSITION SENSOR CIRCUIT LOST SIGNAL.
POSSIBLE CAUSES CKP MOUNTING AND FLYWHEEL CRANKSHAFT POSITION SENSOR ENGINE CONTROL MODULE OPEN SHIELD CIRCUIT INTERMITTENT CONDITION CRANKSHAFT POSITION SENSOR SIGNAL CIRCUIT(S) SHORTED TO GROUND CKP SENSOR CIRCUITS SHORTED TOGETHER CKP SENSOR SIGNAL CIRCUITS OPEN CKP SENSOR SIGNAL CIRCUIT(S) SHORTED TO VOLTAGE
TEST 1 ACTION NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. Attempt to start the engine. Did the engine start? Yes No Go To Go To 2 3 APPLICABILITY All
146
P2045-CRANKSHAFT POSITION SENSOR CIRCUIT LOST SIGNAL
Continued
TEST 2 ACTION WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING. NOTE: The conditions that set the DTC are not present at this time. The following list may help in identifying the intermittent condition. With the engine running at normal operating temperature, monitor the DRB parameters related to the DTC while wiggling the wiring harness. Look for parameter values to change and/or a DTC to set. Review the DTC When Monitored and Set Conditions. If possible, try to duplicate the conditions under which the DTC was set. Refer to any Technical Service Bulletins (TSB) that may apply. Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or partially broken wires. Visually inspect the related wiring harness connectors. Look for broken, bent, pushed out, or corroded terminals. Were any of the above conditions present? Yes No 3 Repair as necessary. Perform ROAD TEST VERIFICATION - VER-2. Test Complete. All APPLICABILITY All
Refer to the Service Information to ensure the Engine Drive Gears/Sprocket are installed correctly and the camshaft and crankshaft gears are timed correctly. Turn the ignition off. Disconnect the CKP Sensor harness connector. Disconnect the ECM harness connectors. Measure the resistance between ground and both of the CKP Sensor Signal circuits. Is the resistance above 1000 ohms for both measurements? Yes No Go To 4
Repair the CKP Sensor Signal circuit(s) for a short to ground. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Disconnect the CKP Sensor harness connector. Disconnect the ECM harness connectors. Measure the resistance between the CKP Sensor Signal circuits. Is the resistance above 1000 ohms? Yes No Go To 5
Repair the CKP Sensor Signal circuits for a short together. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Disconnect the CKP Sensor harness connector. Disconnect the ECM harness connectors. Measure the resistance of CKP Sensor Signal circuits. Is the resistance below 10.0 ohms for both measurements? Yes No Go To 6
Repair the CKP Sensor Signal circuit(s) for an open. Perform ROAD TEST VERIFICATION - VER-2.
147
P2045-CRANKSHAFT POSITION SENSOR CIRCUIT LOST SIGNAL
Continued
TEST 6 ACTION Turn the ignition off. Disconnect the CKP Sensor harness connector. Disconnect the ECM harness connectors. Remove the Engine Control Relay. Connect a jumper wire between cavity 30 and cavity 87 of the Engine Control Relay connector. Turn the ignition on. Measure the voltage of both CKP Sensor Signal circuits. Is the voltage below 1.0 volt for both measurements? Yes No 7 Go To 7 APPLICABILITY All
Repair the CKP Sensor Signal circuit(s) for a short to voltage. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Using the DRB lab scope, backprobe both of the CKP Sensor Signal circuits at the ECM harness connector. NOTE: Refer to Charts and Graphs to view a correct CKP Sensor signal. Start the engine, if the engine will not start, crank the engine for several seconds while monitoring the DRB. Does the DRB display a steady clean CKP Signal pattern for both circuits? Yes No Go To 8
Replace the Crankshaft Position Sensor. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Inspect the CKP Sensor Shield circuit. Were any problems found? Yes No Repair the Shield circuit as necessary. Perform ROAD TEST VERIFICATION - VER-2. Go To 9
Turn the ignition off. Inspect the CKP Sensor for signs of damage or improper/loose attachment to the engine. Inspect the flywheel for excessive dirt contamination or tooth damage which can cause improper CKP Sensor signal output. Where any of these problems found? Yes No Repair or replace as necessary. Perform ROAD TEST VERIFICATION - VER-2. Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2.
All
148
Symptom: P2062-ENGINE OIL SENSOR MONITORING ERROR
POSSIBLE CAUSES ENGINE OIL SENSOR VERIFY THE CURRENT DTC

TEST 1 ACTION Turn the ignition off. Check the engine oil level. Add or remove as necessary to obtain proper engine oil level. Start the engine and allow it to reach operating temperature. Test drive the vehicle. With the DRBIII , read the ECM DTCs. Did this DTC set again? Yes No Replace the Engine Oil Sensor. Perform ROAD TEST VERIFICATION - VER-2. Test complete. Perform ROAD TEST VERIFICATION - VER-2. APPLICABILITY All
149
Symptom List: P2066-MASS AIR FLOW SENSOR PLAUSIBILITY P2355-EGR FLOW RATE IS TOO HIGH P2355-EGR FLOW RATE IS TOO LOW
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P2066-MASS AIR FLOW SENSOR PLAUSIBILITY.
When Monitored and Set Condition: P2066-MASS AIR FLOW SENSOR PLAUSIBILITY When Monitored: Set Condition: EGR flow. With the engine running.
The ECM detects a rationality problem with the MAF Sensor or excessive
POSSIBLE CAUSES AIR FILTER AIR RESTRICTION CHECKING FOR AIR LEAKS EGR ACTUATION - 1200 RPM EGR VALVE MAF SENSOR MAF SENSOR READING - 3OOO RPM INTERMITTENT CONDITION EGR RESTRICTION
TEST 1 ACTION NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. Turn the ignition on. With the DRB, erase ECM DTCs. Test drive the vehicle and monitor the DRB for ECM DTCs. Did this DTC set again? Yes No Go To Go To 2 10 APPLICABILITY All
150
P2066-MASS AIR FLOW SENSOR PLAUSIBILITY
TEST 2 ACTION Start and idle the engine. With the DRBIII in Sensors, read the MAF mg/strk and compare it to the MAF SPEC mg/strk with the engine at idle. NOTE: The MAF Sensor reading should be within 5% of the MAF Spec reading. Is the MAF Sensor reading within 5% of the MAF Spec? Yes No 3 Go To Go To 3 7 All
Continued
APPLICABILITY All
Place the transmission in Park or Neutral for this test. Start the engine and increase engine the engine speed to 3000 RPM. With the DRBIII in Sensors, read the MAF mg/strk and compare it to the MAF SPEC mg/strk with the engine speed at 3000 RPM. NOTE: The MAF Sensor reading should be within 5% of the MAF Spec reading. Is the MAF Sensor reading within 5% of the MAF Spec? Yes No Go To Go To 4 7
NOTE: Inspect the complete exhaust system for restriction. Restrictions in the exhaust system can cause improper EGR flow. Repair as necessary Allow the engine to idle until the engine reaches operating temperature. With the DRBIII , actuate the EGR Positioner with the engine idling. NOTE: The EGR Positioner will actuate from 5% to 95%. With the engine idling at approximately 680 RPM the MAF reading should switch a minimum of 200 mg/strk between 5% and 95% of EGR actuation. Note the MAF readings. Does the MAF switch a minimum of 200 mg/strk between 5% and 95% of EGR actuation? Yes No Go To Go To 5 6
All
Allow the engine to idle until the engine reaches operating temperature. With the DRBIII , actuate the EGR Positioner with the engine speed at 1200 RPM. NOTE: The EGR Positioner will actuate from 5% to 95%. With the engine speed at approximately 1200 RPM the MAF reading should switch a minimum of 200 mg/strk between 5% and 95% of EGR actuation. Note the MAF readings. Does the MAF switch a minimum of 200 mg/strk between 5% and 95% of EGR actuation? Yes No No problem found. Test complete. Perform ROAD TEST VERIFICATION - VER-2. Go To 6
All
Turn the ignition off. Remove the EGR valve and check the valve and flow passages for debris or other restrictions. Were any problems found? Yes No Clean or repair as necessary. Perform ROAD TEST VERIFICATION - VER-2. Replace the EGR Valve. Perform ROAD TEST VERIFICATION - VER-2.
All
151
P2066-MASS AIR FLOW SENSOR PLAUSIBILITY
TEST 7 ACTION Turn the ignition off. Remove and inspect the Air Filter for soiling or excessive dirt and debris which may cause air flow restriction. Were any of these problems found? Yes No 8 Replace the Air Filter element. Perform ROAD TEST VERIFICATION - VER-2. Go To 8 All
Continued
APPLICABILITY All
NOTE: Inspect all air intake and turbocharger related tubes for damage, restriction or poor connection. Any of these conditions can cause a this DTC to set. NOTE: Inspect the exhaust system and related tubes for damage, restriction or poor connection. Any of these conditions can cause a this DTC to set. Turn the ignition off. Inspect the intake system, exhaust system and related tubes and connections. Were any problems found? Yes No Repair or replace as necessary. Perform ROAD TEST VERIFICATION - VER-2. Go To 9
Turn the ignition off. Remove the Intake Air Temperature Sensor. Connect smoke machine 84-04 to the Intake Air Temperature Sensor port in the intake duct and begin injecting smoke into the intake system. Observe all intake system components for evidence of smoke leakage. Is there evidence of smoke leakage? Yes No Repair or replace as necessary. Perform ROAD TEST VERIFICATION - VER-2. Replace the MAF Sensor. Perform ROAD TEST VERIFICATION - VER-2.
All
10
All
152
Symptom List: P2066-MASS AIR FLOW SENSOR PLAUSIBILITY AIR MASS TOO HIGH P2066-MASS AIR FLOW SENSOR PLAUSIBILITY AIR MASS TOO LOW
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P2066-MASS AIR FLOW SENSOR PLAUSIBILITY AIR MASS TOO HIGH.
When Monitored and Set Condition: P2066-MASS AIR FLOW SENSOR PLAUSIBILITY AIR MASS TOO HIGH When Monitored: Set Condition: With the engine running.
The ECM detects excessive air flow from the MAF Sensor.
P2066-MASS AIR FLOW SENSOR PLAUSIBILITY AIR MASS TOO LOW When Monitored: Set Condition: With the engine running.
The ECM detects low air flow from the MAF Sensor.
POSSIBLE CAUSES AIR FILTER AIR RESTRICTION CHECKING FOR AIR LEAKS MASS AIRFLOW SENSOR INTERMITTENT CONDITION
153
P2066-MASS AIR FLOW SENSOR PLAUSIBILITY AIR MASS TOO HIGH
Continued
TEST 1 ACTION NOTE: If DTC P1611, P2306 or P2332 is present with this DTC, diagnose DTCs P1611, P2306 or P2332 before diagnosing this DTC. NOTE: Inspect all air intake and turbocharger related tubes for damage, restriction or poor connection. Any of these conditions can cause a this DTC to set. NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. Turn the ignition on. With the DRBIII , erase the ECM DTCs. Test drive the vehicle. With the DRBIII , read the ECM DTCs. Does the DRB III display a Mass Air Flow Sensor DTC? Yes No 2 Go To Go To 2 5 All APPLICABILITY All
NOTE: Inspect all air intake and turbocharger related tubes for damage, restriction or poor connection. Any of these conditions can cause a this DTC to set. NOTE: Inspect the exhaust system and related tubes for damage, restriction or poor connection. Any of these conditions can cause a this DTC to set. Turn the ignition off. Inspect the intake system, exhaust system and related tubes and connections. Were any problems found? Yes No Repair or replace as necessary. Perform ROAD TEST VERIFICATION - VER-2. Go To 4
All
Turn the ignition off. Remove the Intake Air Temperature Sensor. Connect smoke machine 84-04 to the Intake Air Temperature Sensor port in the intake duct and begin injecting smoke into the intake system. Observe all intake system components for evidence of smoke leakage. Is there evidence of smoke leakage? Yes No Repair or replace as necessary. Perform ROAD TEST VERIFICATION - VER-2. Replace the MAF Sensor. Perform ROAD TEST VERIFICATION - VER-2.
All
154
P2066-MASS AIR FLOW SENSOR PLAUSIBILITY AIR MASS TOO HIGH
Continued
155
Symptom: P2087-INTAKE PRESSURE SENSOR INTAKE RESTRICTION
When Monitored and Set Condition: P2087-INTAKE PRESSURE SENSOR INTAKE RESTRICTION When Monitored: Set Condition: With the ignition on.
POSSIBLE CAUSES RESTRICTED INTAKE SYSTEM
Repair Instructions: RESTRICTED INTAKE SYSTEM This DTC indicates a restriction in the intake system. Check for clogged air filter, collapsed hoses, or other conditions that could cause restricted air flow through the intake system. Repair or replace as necessary. Perform ROAD TEST VERIFICATION - VER-2.
156
Symptom List: P2100-FUEL PUMP RELAY CIRCUIT OPEN CIRCUIT P2100-FUEL PUMP RELAY CIRCUIT SHORTED TO GROUND
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P2100-FUEL PUMP RELAY CIRCUIT OPEN CIRCUIT.
POSSIBLE CAUSES INTERMITTENT CONDITION ENGINE CONTROL RELAY OUTPUT CIRCUIT OPEN FUEL LIFT PUMP RELAY FUEL LIFT PUMP RELAY CONTROL CIRCUIT SHORTED TO GROUND FUEL LIFT PUMP RELAY CONTROL CIRCUIT OPEN ENGINE CONTROL MODULE
TEST 1 ACTION NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. Turn the ignition on. With the DRBIII , erase the ECM DTCs. Crank and attempt to start the engine several times. With the DRBIII , read the active ECM DTCs. Did this DTC set again? Yes No 2 Go To Go To 2 6 All APPLICABILITY All
Turn the ignition off. Remove the Fuel Lift Pump Relay. Turn the ignition on. Using a 12-volt test light connected to ground, check the Engine Control Relay Output circuit. Did the test light illuminate brightly? Yes No Go To 3
Refer to Checking the ECM Power and Grounds for the related symptom(s). Perform ROAD TEST VERIFICATION - VER-2.
157
P2100-FUEL PUMP RELAY CIRCUIT OPEN CIRCUIT
TEST 3 ACTION Turn the ignition off. Install a substitute relay in place of the Fuel Lift Pump Relay. Turn the ignition on. With the DRB, actuate the Fuel Lift Pump Relay. Does the Fuel Lift Pump Relay cycle on and off? Yes No 4 Replace the Fuel Lift Pump Relay. Perform ROAD TEST VERIFICATION - VER-2. Go To 4 All
Continued
APPLICABILITY All
Turn the ignition off. Remove the Fuel Lift Pump Relay. Disconnect the ECM harness connectors. Measure the resistance between ground and the Fuel Lift Pump Relay Control circuit. Is the resistance above 1000 ohms? Yes No Go To 5
Repair the Fuel Lift Pump Relay Control circuit for a short to ground. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Remove the Fuel Lift Pump Relay. Disconnect the ECM harness connectors. Measure the resistance of the Fuel Lift Pump Relay Control circuit. Is the resistance below 10.0 ohms? Yes Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Repair the Fuel Lift Pump Relay Control circuit for an open. Perform ROAD TEST VERIFICATION - VER-2.
No 6
All
158
Symptom List: P2100-FUEL PUMP RELAY CIRCUIT SHORTED TO VOLTAGE P2100-FUEL PUMP RELAY EXCESSIVE CURRENT
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P2100-FUEL PUMP RELAY CIRCUIT SHORTED TO VOLTAGE.
POSSIBLE CAUSES INTERMITTENT CONDITION FUEL LIFT PUMP RELAY FUEL LIFT PUMP RELAY CONTROL CIRCUIT SHORTED TO VOLTAGE ENGINE CONTROL MODULE
TEST 1 ACTION NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. Turn the ignition on. With the DRB, actuate the Fuel Lift Pump Relay. Does the Fuel Lift Pump Relay cycle on and off? Yes No 2 Go To Go To 2 3 All APPLICABILITY All
159
P2100-FUEL PUMP RELAY CIRCUIT SHORTED TO VOLTAGE Continued
TEST 3 ACTION Turn the ignition off. Install a substitute relay in place of the Fuel Lift Pump Relay. Turn the ignition on. With the DRB, actuate the Fuel Lift Pump Relay. Does the Fuel Lift Pump Relay cycle on and off? Yes No 4 Replace the Fuel Lift Pump Relay. Perform ROAD TEST VERIFICATION - VER-2. Go To 4 All APPLICABILITY All
Turn the ignition off. Remove the Fuel Lift Pump Relay. Remove the Engine Control Relay. Connect a jumper wire between cavity 30 and cavity 87 of the Engine Control Relay connector. Turn the ignition on. Measure the voltage of the Fuel Lift Pump Relay Control circuit. Is the voltage below 1.0 volt? Yes Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Repair the Fuel Lift Pump Relay Control circuit for a short to voltage. Perform ROAD TEST VERIFICATION - VER-2.
No
160
Symptom List: P2104-STARTER RELAY CIRCUIT SHORT CIRCUIT P2152-STARTER RELAY CIRCUIT SHORT TO GROUND P2153-STARTER RELAY CIRCUIT OPEN OR SHORTED TO VOLTAGE
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P2104-STARTER RELAY CIRCUIT SHORT CIRCUIT.
When Monitored and Set Condition: P2104-STARTER RELAY CIRCUIT SHORT CIRCUIT When Monitored: Set Condition: circuit. During engine crank attempt.
The ECM detects too much current on the Starter Motor Relay Control
POSSIBLE CAUSES CHECKING THE ENGINE CONTROL RELAY SYSTEM INTERMITTENT CONDITION SUBSTITUTE STARTER RELAY STARTER RELAY CONTROL CIRCUIT SHORTED TO GROUND STARTER RELAY CONTROL CIRCUIT SHORTED TO VOLTAGE ENGINE CONTROL MODULE STARTER RELAY CONTROL CIRCUIT OPEN
TEST 1 ACTION NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. Turn the ignition on. With the DRB, erase ECM DTCs. Attempt to start the engine several times, pausing for at least 10 seconds between each cycle. Turn the ignition on. With the DRB, read ECM DTCs. Did this DTC set again? Yes No Go To Go To 2 8 APPLICABILITY All
161
P2104-STARTER RELAY CIRCUIT SHORT CIRCUIT
TEST 2 ACTION NOTE: If DTC P1611, P2306 or P2332 is present with this DTC, diagnose DTCs P1611, P2306 or P2332 before diagnosing this DTC. NOTE: Check the ECM for other ECM DTCs related to circuits that are open, shorted to ground or low voltage problems. Does the DRB also display these type of DTCs? Yes No 3 Go To Go To 3 4 All
Continued
APPLICABILITY All
Turn the ignition off. Install a substitute relay in place of the Starter Relay. Turn the ignition on. With the DRBIII , erase DTCs. Attempt to start the engine several times, pausing for at least 10 seconds between each cycle. Turn the ignition on. With the DRB, read ECM DTCs. Did this DTC set again? Yes No Go To 5
Replace the Starter Relay. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Remove the Starter Relay. Disconnect the ECM harness connectors. Measure the resistance of the Starter Relay Control circuit. Is the resistance below 10.0 ohms? Yes No Go To 6
Repair the Starter Relay Control circuit for an open. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Remove the Starter Relay. Disconnect the ECM harness connectors. Measure the resistance between ground and the Starter Relay Control circuit. Is the resistance above 1000 ohms? Yes No Go To 7
Repair the Starter Relay Control circuit for a short to ground. Perform ROAD TEST VERIFICATION - VER-2.
162
P2104-STARTER RELAY CIRCUIT SHORT CIRCUIT
TEST 7 ACTION Turn the ignition off. Remove the Starter Relay. Disconnect the ECM harness connectors. Remove the Engine Control Relay. Connect a jumper wire between cavity 30 and cavity 87 of the Engine Control Relay connector. Turn the ignition on. Measure the voltage of the Starter Relay Control circuit. Is the voltage below 1.0 volt? Yes Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Repair the Starter Relay Control circuit for a short to voltage. Perform ROAD TEST VERIFICATION - VER-2. All
Continued
APPLICABILITY All
No 8
163
Symptom List: P2110-BOOST PRESSURE SERVO MOTOR CIRCUIT SHORT CIRCUIT P2112-BOOST PRESSURE SERVO MOTOR CIRCUIT EXCESSIVE CURRENT P2526-BOOST PRESSURE SERVO MOTOR SHORT TO VOLTAGE
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P2110-BOOST PRESSURE SERVO MOTOR CIRCUIT SHORT CIRCUIT.
When Monitored and Set Condition: P2110-BOOST PRESSURE SERVO MOTOR CIRCUIT SHORT CIRCUIT When Monitored: With the ignition on.
Set Condition: The ECM detects a short to battery on the Boost Pressure Servo Motor Control circuit.
POSSIBLE CAUSES INTERMITTENT CONDITION BOOST PRESSURE SERVO MOTOR BOOST PRESSURE SERVO MOTOR CONTROL SHORT TO VOLTAGE ENGINE CONTROL MODULE - INTERNAL ENGINE CONTROL MODULE - INTERNAL SHORT TO VOLTAGE
TEST 1 ACTION NOTE: If DTC P1611, P2306 or P2332 is present with this DTC, diagnose DTCs P1611, P2306 or P2332 before diagnosing this DTC. NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. Turn the ignition on. With the DRB, erase ECM DTCs. Test drive the vehicle and monitor the DRB for ECM DTCs. Did this DTC set again? Yes No Go To Go To 2 5 APPLICABILITY All
164
P2110-BOOST PRESSURE SERVO MOTOR CIRCUIT SHORT CIRCUIT
Continued
TEST 2 ACTION Turn the ignition off. Disconnect the Boost Pressure Servo Motor harness connector. Turn the ignition on. With the DRB, erase ECM DTCs. Monitor the DRB for ECM DTCs. Does the DRB display BOOST PRESSURE SERVO MOTOR OPEN CIRCUIT? Yes No 3 Replace the Boost Pressure Servo Motor. Perform ROAD TEST VERIFICATION - VER-2. Go To 3 All APPLICABILITY All
Turn the ignition off. Disconnect the Boost Pressure Servo Motor harness connector. Turn the ignition on. Measure the voltage of the Boost Pressure Servo Motor Control circuit. Is the voltage below 0.5 volt? Yes Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Go To 4
No 4
Turn the ignition off. Disconnect the Boost Pressure Servo Motor harness connector. Disconnect the ECM harness connectors. Remove the Engine Control Relay. Connect a jumper wire between cavity 30 and cavity 87 of the Engine Control Relay connector. Turn the ignition on. Measure the voltage of the Boost Pressure Servo Motor Control circuit. Is the voltage below 0.5 volt? Yes Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Repair the Boost Pressure Servo Motor Control circuit for a short to voltage. Perform ROAD TEST VERIFICATION - VER-2.
All
No
165
P2110-BOOST PRESSURE SERVO MOTOR CIRCUIT SHORT CIRCUIT
Continued
166
Symptom List: P2111-BOOST GROUND P2112-BOOST CUIT P2510-BOOST P2526-BOOST P2526-BOOST
PRESSURE SERVO MOTOR CIRCUIT SHORT TO PRESSURE SERVO MOTOR CIRCUIT OPEN CIRPRESSURE SERVO MOTOR SHORT TO GROUND PRESSURE SERVO MOTOR OPEN CIRCUIT PRESSURE SERVO MOTOR SHORT TO GROUND
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P2111-BOOST PRESSURE SERVO MOTOR CIRCUIT SHORT TO GROUND.
When Monitored and Set Condition: P2111-BOOST PRESSURE SERVO MOTOR CIRCUIT SHORT TO GROUND When Monitored: With the ignition on.
Set Condition: The ECM detects a short to battery on the Boost Pressure Servo Motor Control circuit. P2112-BOOST PRESSURE SERVO MOTOR CIRCUIT OPEN CIRCUIT When Monitored: With the ignition on.
Set Condition: The ECM detects an open or short to ground on the Boost Pressure Servo Motor Control circuit.
POSSIBLE CAUSES CHECKING THE ENGINE CONTROL RELAY SYSTEM INTERMITTENT CONDITION 12 VOLT SUPPLY CIRCUIT OPEN BOOST PRESSURE SERVO MOTOR CONTROL CIRCUIT SHORTED TO GROUND BOOST PRESSURE SERVO MOTOR CONTROL CKT OPEN BOOST PRESSURE SERVO MOTOR ENGINE CONTROL MODULE
167
P2111-BOOST PRESSURE GROUND Continued
TEST 1
SERVO
ACTION
MOTOR
CIRCUIT
SHORT
TO
APPLICABILITY All
NOTE: If DTC P1611, P2306 or P2332 is present with this DTC, diagnose DTCs P1611, P2306 or P2332 before diagnosing this DTC. NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. Turn the ignition on. With the DRB, erase ECM DTCs. Test drive the vehicle. Monitor the DRB for ECM DTCs. Did this DTC set again? Yes No Go To Go To 2 8
All
Turn the ignition off. Disconnect the ECM harness connectors. Connect a jumper wire between ground and the Engine Control Relay Signal circuit in ECM C2 harness connector cavity 44. Turn the ignition on. Using a 12-volt test light connected to ground, check the Fused Engine Control Relay Output circuits at the ECM C1 harness connector cavities 1, 3 and 5. Does the test light illuminate brightly for each circuit? Yes No Go To 4
All
Turn the ignition off. Disconnect the Boost Pressure Servo Motor harness connector. Turn the ignition on. Using a 12-volt test light connected to ground, check the 12 Volt Supply circuit in the Boost Pressure Servo Motor harness connector. Does the test light illuminate brightly? Yes No Go To 5
Repair the 12 Volt Supply circuit for an open. Perform ROAD TEST VERIFICATION - VER-2.
168
TEST 5
SERVO
ACTION
MOTOR
CIRCUIT
SHORT
TO
APPLICABILITY All
Turn the ignition off. Disconnect the Boost Pressure Servo Motor harness connector. Disconnect the ECM harness connectors. Measure the resistance between the Boost Pressure Servo Motor Control circuit in the Boost Pressure Servo Motor harness connector and ground. Is the resistance above 1000 ohms? Yes No Go To 6
Repair the Boost Pressure Servo Motor Control circuit for a short to ground. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Disconnect the Boost Pressure Servo Motor harness connector. Disconnect the ECM harness connectors. Measure the resistance of the Boost Pressure Servo Motor Control circuit. Is the resistance below 10.0 ohms? Yes No Go To 7
Repair the Boost Pressure Servo Motor Control circuit for an open. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Install a substitute Boost Pressure Servo Motor in place of the vehicles Boost Pressure Servo Motor. NOTE: Ensure the ECM and Boost Pressure Servo Motor harness connectors are connected. Turn the ignition on. With the DRB, check for this DTC to set again. Did this DTC set again? Yes Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Replace the Boost Pressure Servo Motor. Perform ROAD TEST VERIFICATION - VER-2.
No
169
TEST 8
SERVO
ACTION
MOTOR
CIRCUIT
SHORT
TO
APPLICABILITY All
WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING. NOTE: The conditions that set the DTC are not present at this time.The following list may help in identifying the intermittent condition. With the engine running at normal operating temperature, monitor the DRB parameters related to the DTC while wiggling the wiring harness. Look for parameter values to change and/or a DTC to set. Review the DTC When Monitored and Set Conditions. If possible, try to duplicate the conditions under which the DTC was set. Refer to any Technical Service Bulletins (TSB) that may apply. Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or partially broken wires. Visually inspect the related wiring harness connectors. Look for broken, bent, pushed out, or corroded terminals. Were any of the above conditions present? Yes No Repair as necessary. Perform ROAD TEST VERIFICATION - VER-2. Test Complete.
170
Symptom List: P2132-GLOW PLUG CONTROL MODULE CIRCUIT OPEN CIRCUIT P2132-GLOW PLUG CONTROL MODULE CIRCUIT SHORTED TO GROUND P2132-GLOW PLUG CONTROL MODULE CIRCUIT SHORTED TO VOLTAGE OR OPEN P2132-GLOW PLUG CONTROL MODULE FAULT
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P2132-GLOW PLUG CONTROL MODULE CIRCUIT OPEN CIRCUIT.
POSSIBLE CAUSES BATTERY SUPPLY CIRCUIT OPEN GROUND CIRCUIT OPEN INTERMITTENT CONDITION GLOW PLUG CONTROL MODULE
TEST 1 ACTION NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. Turn the ignition on. With the DRB, erase ECM DTCs. Turn the ignition off for 10 seconds. Turn the ignition on. Monitor the DRB for ECM DTCs. Repeat this test several times. Did this DTC set again? Yes No 2 Go To Go To 2 4 All APPLICABILITY All
Turn the ignition off. Disconnect the Glow Plug Control Module harness connector. Using a 12-volt test light connected to 12-volts, check the Ground circuit at the Glow Plug Control Module harness connector. Does the test light illuminate brightly? Yes No Go To 3
Repair the Glow Plug Control Module Ground circuit for an open. Perform ROAD TEST VERIFICATION - VER-2.
171
P2132-GLOW PLUG CONTROL MODULE CIRCUIT OPEN CIRCUIT
Continued
TEST 3 ACTION Turn the ignition off. Disconnect the Glow Plug Control Module harness connector. Using a 12-volt test light connected to ground, check the Battery Supply circuit at the Glow Plug Control Module harness connector. Does the test light illuminate brightly? Yes No Replace the Glow Plug Control Module. Perform ROAD TEST VERIFICATION - VER-2. Repair the Glow Plug Control Module Battery Supply circuit for an open. Perform ROAD TEST VERIFICATION - VER-2. All APPLICABILITY All
172
Symptom List: P2151-FUEL PRESS SOLENOID SIGNAL PLAUSIBILITY HIGH P2151-FUEL PRESS SOLENOID SIGNAL PLAUSIBILITY LOW P2500-FUEL PRESSURE SOLENOID CIRCUIT OPEN CIRCUIT P2501-FUEL PRESSURE SOLENOID CIRCUIT SHORTED TO GROUND OR B+
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P2151-FUEL PRESS SOLENOID SIGNAL PLAUSIBILITY HIGH.
When Monitored and Set Condition: P2500-FUEL PRESSURE SOLENOID CIRCUIT OPEN CIRCUIT When Monitored: With the ignition on.
Set Condition: The ECM detects an open or short to ground on the Fuel Pressure Solenoid Control circuit. P2501-FUEL PRESSURE SOLENOID CIRCUIT SHORTED TO GROUND OR B+ When Monitored: With the ignition on and the ECM attempting to actuate the Fuel Pressure Solenoid. Set Condition: The ECM detects excessive current on the Fuel Pressure Solenoid Control circuit when attempting to actuate the Fuel Pressure Solenoid.
POSSIBLE CAUSES CHECKING THE ENGINE CONTROL RELAY SYSTEM INTERMITTENT CONDITION FUEL PRESSURE SOLENOID CONTROL SHORTED TO VOLTAGE FUEL PRESSURE SOLENOID CONTROL CIRCUIT SHORTED TO GROUND FUEL PRESSURE SOLENOID CONTROL CIRCUIT OPEN FUEL PRESSURE SOLENOID ENGINE CONTROL MODULE
173
P2151-FUEL PRESS SOLENOID SIGNAL PLAUSIBILITY HIGH
Continued
TEST 1 ACTION NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. WARNING: HIGH-PRESSURE FUEL LINES DELIVER DIESEL FUEL UNDER EXTREME PRESSURE FROM THE INJECTION PUMP TO THE FUEL INJECTORS. THIS MAY BE AS HIGH AS 23,200 PSI (1600 BAR). USE EXTREME CAUTION WHEN INSPECTING FOR HIGH-PRESSURE FUEL LEAKS. WARNING: FUEL UNDER THIS AMOUNT OF PRESSURE CAN PENETRATE SKIN CAUSING PERSONAL INJURY OR DEATH. INSPECT FOR HIGH-PRESSURE FUEL LEAKS WITH A SHEET OF CARDBOARD. WEAR SAFETY GOGGLES AND ADEQUATE PROTECTIVE CLOTHING WHEN SERVICING FUEL SYSTEM. Turn the ignition on. With the DRB, erase ECM DTCs. Start the engine several times, turning the ignition off for at least 30 seconds between each run cycle. Monitor the DRB for ECM DTCs. Did this DTC set again? Yes No 2 Go To Go To 2 8 All APPLICABILITY All
All
Refer to symptom list and perform Checking the ECM Power and Grounds. Perform ROAD TEST VERIFICATION - VER-2.
174
Continued
TEST 4 ACTION Turn the ignition off. Disconnect the Fuel Pressure Solenoid harness connector. Disconnect the ECM harness connectors. Remove the Engine Control Relay. Connect a jumper wire between cavity 30 and cavity 87 of the Engine Control Relay connector. Turn the ignition on. Measure the voltage of the Fuel Pressure Solenoid Control circuit. Is the voltage below 1.0 volt? Yes No Go To 5 APPLICABILITY All
Repair the Fuel Pressure Solenoid Control circuit for a short to voltage. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Disconnect the Fuel Pressure Solenoid harness connector. Disconnect the ECM harness connectors. Measure the resistance between ground and the Fuel Pressure Solenoid Control circuit. Measure the resistance between ground and the Fuel Pressure Solenoid 12-volt Supply Is the resistance above 1000 ohms for both measurements? Yes No Go To 6
Repair the Fuel Pressure Solenoid circuit(s) for a short to ground. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Disconnect the Fuel Pressure Solenoid harness connector. Disconnect the ECM harness connectors. Measure the resistance of the Fuel Pressure Solenoid Control circuit. Measure the resistance of the Fuel Pressure Solenoid 12-volt Supply circuit. Is the resistance below 10.0 ohms for both measurements? Yes No Go To 7
Repair the Fuel Pressure Solenoid circuit(s) for an open. Perform ROAD TEST VERIFICATION - VER-2.
175
Continued
TEST 7 ACTION Turn the ignition off. Disconnect the Fuel Pressure Solenoid harness connector. Turn the ignition on. With the DRB, erase ECM DTCs. Monitor the DRB for ECM DTCs. NOTE: The DRB should display P2500-FUEL PRESSURE SOLENOID OPEN CIRCUIT. Turn the ignition off. Connect a jumper wire between cavity 1 and cavity 2 of the Fuel Pressure Solenoid harness connector. Turn the ignition on. With the DRB, erase ECM DTCs. Monitor the DRB for ECM DTCs. NOTE: The DRB should display P2501-FUEL PRESSURE SOLENOID SHORT CIRCUIT. Does the DRB display the appropriate DTC for each condition? Yes Replace the Fuel Pressure Solenoid in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. All APPLICABILITY All
No
176
Symptom List: P2197-FUEL P2198-FUEL P2199-FUEL P2502-FUEL
QUANTITY QUANTITY QUANTITY QUANTITY
SOLENOID SOLENOID SOLENOID SOLENOID
OPEN CIRCUIT SHORT TO VOLTAGE SHORT TO GROUND SHORT TO GROUND
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P2197-FUEL QUANTITY SOLENOID OPEN CIRCUIT.
POSSIBLE CAUSES CHECKING ECM POWER AND GROUNDS CHECKING THE ENGINE CONTROL RELAY SYSTEM FUEL QUANTITY SOLENOID FUEL QUANTITY SOLENOID CIRCUIT(S) SHORTED TO GROUND FUEL QUANTITY SOLENOID CIRCUIT(S) SHORTED TO VOLTAGE FUEL QUANTITY SOLENOID CIRCUIT(S) SHORTED TOGETHER FUEL QUANTITY SOLENOID OPEN CIRCUIT(S) INTERMITTENT CONDITION
TEST 1 ACTION Turn the ignition on. With the DRBIII , erase ECM DTCs. Perform several engine run cycles, turning the ignition off for at least 20 seconds between each engine run cycle. With the DRBIII , read the ECM DTCs. Did this DTC set again? Yes No Go To Go To 2 7 APPLICABILITY All
177
P2197-FUEL QUANTITY SOLENOID OPEN CIRCUIT
TEST 2 ACTION Turn the ignition off. Disconnect the ECM harness connectors. Connect a jumper wire between ground and the Engine Control Relay Control circuit in ECM C2 harness connector cavity 44. Turn the ignition on. Using a 12-volt test light connected to ground, check the Fused Engine Control Relay Output circuits at the ECM C2 harness connector cavities 1, 3 and 5. Choose the appropriate result. Test light is on for all circuits. Go To 3 Test light is on for 1 or 2 circuits Repair the Engine Control Relay Output circuit(s) that did not illuminate brightly for an open. Perform ROAD TEST VERIFICATION - VER-2. Light off for all circuits. Refer to symptom Checking the ECM Power and Grounds. Perform ROAD TEST VERIFICATION - VER-2. 3 Turn the ignition off. Disconnect the ECM harness connectors. Disconnect the Fuel Quantity Solenoid harness connector. Measure the resistance of each of the Fuel Quantity Solenoid circuits between the ECM harness connector and the Fuel Quantity Solenoid harness connector. Is the resistance below 10.0 ohms for each measurement? Yes No 4 Go To 4 All
Continued
APPLICABILITY All
Repair the circuit(s) that measured above 10.0 ohms for an open. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Disconnect the ECM harness connectors. Disconnect the Fuel Quantity Solenoid harness connector. Measure the resistance between ground and each of the Fuel Quantity Solenoid circuits. Is the resistance above 1000 ohms for each measurement? Yes No Go To 5
Repair the circuit(s) that measured below 1000 ohms for a short to ground. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Disconnect the ECM harness connectors. Disconnect the Fuel Quantity Solenoid harness connector. Measure the resistance between the Fuel Quantity Solenoid circuits. Is the resistance above 1000 ohms? Yes No Go To 6
Repair the Fuel Quantity Solenoid circuits for a short together. Perform ROAD TEST VERIFICATION - VER-2.
178
P2197-FUEL QUANTITY SOLENOID OPEN CIRCUIT
TEST 6 ACTION Turn the ignition off. Disconnect the ECM harness connectors. Disconnect the Fuel Quantity Solenoid harness connector. Remove the Engine Control Relay. Connect a jumper wire between cavity 30 and cavity 87 of the Engine Control Relay connector. Turn the ignition on. Measure the voltage each of the Fuel Quantity Solenoid circuits. Is the voltage below 1.0 volt for each measurement? Yes Replace the Fuel Quantity Solenoid in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Repair the circuit(s) that measured above 1.0 volts for a short to voltage. Perform ROAD TEST VERIFICATION - VER-2. All
Continued
APPLICABILITY All
No
179
Symptom List: P2203-TORQUE REDUCTION MESSAGE FROM ABS - CAN PLAUSIBILITY P2203-TORQUE REDUCTION MESSAGE FROM ABS - MESSAGE ERROR P2203-TORQUE REDUCTION MESSAGE FROM ABS - MESSAGES MISSING P2203-TORQUE REDUCTION MESSAGE FROM ABS - NO COMMUNIOCATION P2203-TORQUE REDUCTION MESSAGE FROM ABS - PLAUSIBILITY #1 P2203-TORQUE REDUCTION MESSAGE FROM ABS PLAUSIBILITY #2 P2208-ABS BRAKE SIGNAL CAN MESSAGE IMPLAUSIBLE P2208-ABS CAN BRAKE SIGNAL PLAUSIBILITY P2209-ABS CAN MESSAGE MISSING OR INCORRECT P2253-STEERING ANGLE SENSOR PLAUSIBILITY
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P2203-TORQUE REDUCTION MESSAGE FROM ABS - CAN PLAUSIBILITY.
POSSIBLE CAUSES CAB DTCS ENGINE CONTROL MODULE VERIFY CAB COMMUNICATION INTERMITTENT CONDITION
TEST 1 ACTION Turn the ignition on. With the DRBIII attempt to communicate with the CAB. NOTE: If there are other DTCs set with this DTC, refer to the Symptom List and repair other stored ECM DTCs before diagnosing this DTC. Is the CAB communicating with the DRB? Yes No Go To 2 APPLICABILITY All
Refer to the appropriate symptom in the Body Diagnostic Information. Perform BODY VERIFICATION TEST - VER 1.
180
P2203-TORQUE REDUCTION MESSAGE FROM ABS - CAN PLAUSIBILITY Continued
TEST 2 ACTION Turn the ignition on. With the DRBIII , read the CAB DTCs. Are there any CAB DTCs? Yes No 3 Refer to symptom list for problems related to CAB. Perform BODY VERIFICATION TEST - VER 1. Go To 3 All APPLICABILITY All
NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. Turn the ignition on. With the DRBIII , erase the ECM DTCs. Turn the ignition off then turn the ignition on and wait 60 seconds. With the DRBIII , read the ECM DTCs. Does the DRB display this DTC? Yes Replace and program the Engine Control Module in accordance with the Service Information. Perform BODY VERIFICATION TEST - VER 1. Go To 4
No 4
All
181
Symptom List: P2204-TORQUE SIBILITY P2204-TORQUE STOP P2204-TORQUE ERROR P2204-TORQUE MISSING P2204-TORQUE ITY P2204-TORQUE P2204-TORQUE
REDUCTION MESSAGE FROM TCM - CAN PLAUREDUCTION MESSAGE FROM TCM - ENGINE REDUCTION MESSAGE FROM TCM - MESSAGE REDUCTION MESSAGE FROM TCM - MESSAGES REDUCTION MESSAGE FROM TCM - PLAUSIBILREDUCTION MESSAGE FROM TCM - TCM DTC #1 REDUCTION MESSAGE FROM TCM - TCM DTC #2
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P2204-TORQUE REDUCTION MESSAGE FROM TCM - CAN PLAUSIBILITY.
POSSIBLE CAUSES ENGINE CONTROL MODULE TCM DTCS VERIFY TCM COMMUNICATION INTERMITTENT CONDITION
TEST 1 ACTION Turn the ignition on. With the DRBIII attempt to communicate with the TCM. NOTE: If there are other DTCs set with this DTC, refer to the Symptom List and repair other stored ECM DTCs before diagnosing this DTC. Is the TCM communicating with the DRB? Yes No Go To 2 APPLICABILITY All
Refer to the appropriate symptom in the Body Diagnostic Information. Perform BODY VERIFICATION TEST - VER 1. All
Turn the ignition on. With the DRBIII , read the TCM DTCs. Are there any TCM DTCs? Yes No Refer to symptom list for problems related to TCM. Perform BODY VERIFICATION TEST - VER 1. Go To 3
182
P2204-TORQUE REDUCTION MESSAGE FROM TCM - CAN PLAUSIBILITY Continued
TEST 3 ACTION NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. Turn the ignition on. With the DRBIII , erase the ECM DTCs. Turn the ignition off then turn the ignition on and wait 60 seconds. With the DRBIII , read the ECM DTCs. Does the DRB display this DTC? Yes Replace and program the Engine Control Module in accordance with the Service Information. Perform BODY VERIFICATION TEST - VER 1. Go To 4 All APPLICABILITY All
No 4
183
Symptom List: P2210-ESM CAN MESSAGE MISSING OR INCORRECT P2234-ABS DTC EXTERNAL QUANTITY CONTROL PRESENT P2252-LATERAL ACCELERATOR SENSOR PLAUSIBILTY
FAULT
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P2210-ESM CAN MESSAGE MISSING OR INCORRECT.
POSSIBLE CAUSES ABS MODULE CAN BUS CIRCUITS OPEN INTERMITTENT CONDITION ABS DTCS
TEST 1 ACTION NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. NOTE: This DTC indicates a communication problem between the TCM and the ECM. Turn the ignition on. With the DRBIII , erase ECM DTCs. Perform several engine run cycles, turning the ignition off for at least 20 seconds between each engine run cycle. With the DRBIII , read the ECM DTCs. Did this DTC set again? Yes No 2 Go To Go To 2 4 All APPLICABILITY All
Turn the ignition on. With the DRBIII , attempt to read ABS DTCs. NOTE: If the DRB is unable to communicate with the ABS Module, refer to the symptom list for problem related to ABS Module Communication. Are there any ABS DTCs? Yes No Refer to symptom list for problems related to ABS DTCs. Perform ROAD TEST VERIFICATION - VER-2. Go To 3
184
P2210-ESM CAN MESSAGE MISSING OR INCORRECT
TEST 3 ACTION Turn the ignition off. Disconnect the ABS Module harness connectors. NOTE: This code can be caused by an intermittent problem in the wiring and connectors to the ABS Module. Inspect the ABS harness connector and associated wiring for signs of poor terminal contact. Turn the ignition on. Measure and note the voltage of both CAN Bus circuit at the ABS Module harness connector. Is the voltage between 2.2 volts and 2.8 volts for each measurement? Yes No 4 Test Complete. Perform ROAD TEST VERIFICATION - VER-2. Repair the CAN Bus circuit(s) for an open. Perform ROAD TEST VERIFICATION - VER-2. All
Continued
APPLICABILITY All
185
Symptom List: P2211-ETC CAN MESSAGE MISSING OR INCORRECT P2258-TCM MESSAGE ERROR P2258-TCM NO CAN MESSAGE
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P2211-ETC CAN MESSAGE MISSING OR INCORRECT.
POSSIBLE CAUSES CAN BUS CIRCUITS OPEN TRANSMISSION CONTROL MODULE INTERMITTENT CONDITION TCM DTCS
TEST 1 ACTION NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. NOTE: This DTC indicates a communication problem between the TCM and the ECM. Turn the ignition on. With the DRBIII , erase ECM DTCs. Perform several engine run cycles, turning the ignition off for at least 20 seconds between each engine run cycle. With the DRBIII , read the ECM DTCs. Did this DTC set again? Yes No 2 Go To Go To 2 4 All APPLICABILITY All
Turn the ignition on. With the DRBIII , attempt to read TCM DTCs. NOTE: If the DRB is unable to communicate with the TCM, refer to the symptom list for problem related to TCM Communication. Are there any TCM DTCs? Yes No Refer to symptom list for problems related to TCM DTCs. Perform ROAD TEST VERIFICATION - VER-2. Go To 3
186
P2211-ETC CAN MESSAGE MISSING OR INCORRECT
TEST 3 ACTION Turn the ignition off. Disconnect the TCM harness connectors. Turn the ignition on. Measure and note the voltage of both CAN Bus circuit at the TCM harness connector. NOTE: This code can be caused by an intermittent problem in the wiring and connectors to the Transmission Control Module. Inspect the Transmission Control Module harness connector and associated wiring for signs of poor terminal contact. Is the voltage between 2.2 volts and 2.8 volts for each measurement? Yes No 4 Test Complete. Perform ROAD TEST VERIFICATION - VER-2. Repair the CAN Bus circuit(s) for an open. Perform ROAD TEST VERIFICATION - VER-2. All
Continued
APPLICABILITY All
187
Symptom List: P2217-TCM DTC INTERNAL FAULT PRESENT P2218-TCM DTC 1-2 AND 4-5 SHIFT SOLENOID FAULT PRESENT P2219-TCM DTC 2-3 SHIFT SOLENOID FAULT PRESENT P2220-TCM DTC 3-4 SHIFT SOLENOID FAULT PRESENT P2221-TCM DTC TORQUE CONVERTER CLUTCH SOLENOID FAULT PRESENT P2222-TCM DTC MODULATING PRESSURE SOLENOID FAULT PRESENT P2223-TCM DTC SHIFT PRESSURE SOLENOID FAULT PRESENT P2224-TCM DTC VALVE VOLTAGE SUPPLY FAULT PRESENT P2225-TCM DTC SPEED SENSOR VOLTAGE FAULT PRESENT P2226-TCM DTC EWM CAN MESSAGE FAULT PRESENT P2227-TCM DTC RIGHT REAR WHEEL SPEED IMPLAUSIBLE FAULT PRESENT P2228-TCM DTC TRANSMISSION RATIO ERROR FAULT PRESENT P2229-TCM DTC CAN MSG IMPLAUSIBLE FAULT PRESENT P2230-TCM DTC TCC EXCESSIVE POWER CONSUMPTION FAULT PRESENT P2231-TCM DTC NOT UNEQUIVOCAL FAULT PRESENT P2232-TCM DTC NEGATIVE GEAR COMPARISON FAULT PRESENT
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P2217-TCM DTC INTERNAL FAULT PRESENT.
POSSIBLE CAUSES VERIFY CURRENT DTC
188
P2217-TCM DTC INTERNAL FAULT PRESENT
TEST 1 ACTION NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. NOTE: This code was set in the ECM by the Transmission Control Module to indicate a transmission fault. Diagnosis of transmission faults should be done using the Transmission Diagnostic Information. NOTE: When repairs have been completed, the ECM and TCM must have codes cleared. Turn the ignition on. With the DRBIII , erase ECM DTCs only. With the DRBIII , read ECM DTCs. Are there any TCM DTCs present in the ECM? Yes Refer to Transmission Diagnostic Information for the related symptom(s). Perform NAG1 TRANSMISSION VERIFICATION TEST - VER 1. Test Complete.
Continued
APPLICABILITY All
No
189
Symptom List: P2240-ABS STEERING ANGLE SENSOR CAN MESSAGE IMPLAUSIBLE 1 P2240-ABS STEERING ANGLE SENSOR CAN MESSAGE IMPLAUSIBLE 2
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P2240-ABS STEERING ANGLE SENSOR CAN MESSAGE IMPLAUSIBLE 1.
POSSIBLE CAUSES CAN BUS CIRCUITS OPEN STEERING ANGLE SENSOR INTERMITTENT CONDITION
TEST 1 ACTION NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. NOTE: This DTC indicates a communication problem between the Steering Angle Sensor and the ECM. Turn the ignition on. With the DRBIII , erase ECM DTCs. Perform several engine run cycles, turning the ignition off for at least 20 seconds between each engine run cycle. With the DRBIII , read the ECM DTCs. Did this DTC set again? Yes No 2 Go To Go To 2 3 All APPLICABILITY All
Turn the ignition off. Disconnect the Steering Angle Sensor harness connector. NOTE: This code can be caused by an intermittent problem in the wiring and connectors to the Steering Angle Sensor. Inspect the Steering Angle Sensor harness connector and associated wiring for signs of poor terminal contact. Turn the ignition on. Measure and note the voltage of both CAN Bus circuit at the Steering Angle Sensor harness connector. Is the voltage between 2.2 volts and 2.8 volts for each measurement? Yes No Test Complete. Perform ROAD TEST VERIFICATION - VER-2. Repair the CAN Bus circuit(s) for an open. Perform ROAD TEST VERIFICATION - VER-2.
190
P2240-ABS STEERING ANGLE SENSOR CAN MESSAGE IMPLAUSIBLE 1 Continued
191
Symptom List: P2242-ABS BRAKE MESSAGE PLAUSIBILITY 1 P2242-ABS BRAKE MESSAGE PLAUSIBILITY 2
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P2242-ABS BRAKE MESSAGE PLAUSIBILITY 1.
POSSIBLE CAUSES CAB DTCS CHECKING BRAKE SWITCH INPUT CONTROLLER ANTILOCK BRAKE MODULE TCM DTCS VERIFY CAB COMMUNICATION VERIFY TCM COMMUNICATION
TEST 1 ACTION NOTE: This DTC can be set if the vehicle operator depresses the brake pedal and the accelerator at the same time (riding the brake pedal). Check with vehicle operator for this type of driving behavior. Turn the ignition on. With the DRBIII attempt to communicate with the CAB. NOTE: If there are other DTCs set with this DTC, refer to the Symptom List and repair other stored ECM DTCs before diagnosing this DTC. Is the CAB communicating with the DRB? Yes No Go To 2 APPLICABILITY All
Turn the ignition on. With the DRBIII , read the CAB DTCs. Are there any CAB DTCs? Yes No Refer to symptom list for problems related to CAB. Perform BODY VERIFICATION TEST - VER 1. Go To 3
Turn the ignition on. With the DRBIII attempt to communicate with the TCM. Is the TCM communicating with the DRB? Yes No Go To 4
All
Refer to the appropriate symptom in the Body Diagnostic Information. Perform BODY VERIFICATION TEST - VER 1.
192
P2242-ABS BRAKE MESSAGE PLAUSIBILITY 1
TEST 4 ACTION Turn the ignition on. With the DRBIII , read the CAB DTCs. Are there any CAB DTCs? Yes No 5 Refer to symptom list for problems related to TCM Perform BODY VERIFICATION TEST - VER 1. Go To 5 All
Continued
APPLICABILITY All
Turn the ignition on. With the DRBIII select TCM then Sensors. Read the Brake Switch input while pressing and releasing the brake pedal several times. With the DRBIII select CAB then Sensors. Read the Brake Switch input while pressing and releasing the brake pedal several times. Is the Brake Switch input operating correctly for both modules? Yes Replace and program the CAB in accordance with the Service Information. Perform BODY VERIFICATION TEST - VER 1. Refer to the Service Information wiring to diagnose brake switch problem. Perform BODY VERIFICATION TEST - VER 1.
No
193
Symptom: P2244-INSTRUMENT CLUSTER MESSAGE PLAUSIBILITY
POSSIBLE CAUSES ENGINE CONTROL MODULE INSTRUMENT CLUSTER DTCS VERIFY INSTRUMENT CLUSTER COMMUNICATION INTERMITTENT CONDITION
TEST 1 ACTION Turn the ignition on. With the DRBIII attempt to communicate with the Instrument Cluster. NOTE: If there are other DTCs set with this DTC, refer to the Symptom List and repair other stored ECM DTCs before diagnosing this DTC. Is the Instrument Cluster communicating with the DRB? Yes No Go To 2 APPLICABILITY All
Turn the ignition on. With the DRBIII , read the Instrument Cluster DTCs. Are there any Instrument Cluster DTCs? Yes No Refer to symptom list for problems related to Instrument Cluster. Perform BODY VERIFICATION TEST - VER 1. Go To 3
NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. Turn the ignition on. With the DRBIII , erase the ECM DTCs. Turn the ignition off then turn the ignition on and wait 60 seconds. With the DRBIII , read the ECM DTCs. Does the DRB display this DTC? Yes Replace and program the Engine Control Module in accordance with the Service Information. Perform BODY VERIFICATION TEST - VER 1. Go To 4
All
No
194
P2244-INSTRUMENT CLUSTER MESSAGE PLAUSIBILITY
TEST 4 ACTION WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING. NOTE: The conditions that set the DTC are not present at this time. The following list may help in identifying the intermittent condition. With the engine running at normal operating temperature, monitor the DRB parameters related to the DTC while wiggling the wiring harness. Look for parameter values to change and/or a DTC to set. Review the DTC When Monitored and Set Conditions. If possible, try to duplicate the conditions under which the DTC was set. Refer to any Technical Service Bulletins (TSB) that may apply. Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or partially broken wires. Visually inspect the related wiring harness connectors. Look for broken, bent, pushed out, or corroded terminals. Were any of the above conditions present? Yes No Repair as necessary. Perform BODY VERIFICATION TEST - VER 1. Test Complete.
Continued
APPLICABILITY All
195
Symptom List: P2259-TORQUE REDUCTION MESSAGE FROM HVAC- PARITY ERROR P2259-TORQUE REDUCTION MESSAGE FROM HVAC- SWITCH SIGNAL ERROR P2259-TORQUE REDUCTION MESSAGE FROM HVAC- SWITCH SIGNAL PLAUSIBILITY
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P2259-TORQUE REDUCTION MESSAGE FROM HVAC- PARITY ERROR.
POSSIBLE CAUSES AUTOMATIC TEMP CONTROL DTC

TEST 1 ACTION NOTE: This DTC indicates the presents of a problem or DTC in the ATC Module. View repair statement. Yes Refer to symptom list for problems related to Automatic Temperature Control. Perform ROAD TEST VERIFICATION - VER-2. APPLICABILITY All
196
Symptom: P229-INSTRUMENT CLUSTER MESSAGE - AMBIENT TEMPERATURE SIGNAL PLAUSIBILITY
POSSIBLE CAUSES INSTRUMENT CLUSTER DTC

TEST 1 ACTION NOTE: This DTC indicates the presents of a problem with the Ambient Temp Sensor input to the Instrument Cluster. View repair statement. Yes Refer to symptom list for problems related to Instrument Cluster. Perform ROAD TEST VERIFICATION - VER-2. APPLICABILITY All
197
POSSIBLE CAUSES BOOST PRESSURE SENSOR FUEL PRESSURE SENSOR VISUAL WIRING AND CONNECTOR INSPECTION INTERMITTENT CONDITION SENSOR SUPPLY VOLTAGE 2 SHORTED TO VOLTAGE ENGINE CONTROL MODULE
Turn the ignition off. Visually inspect the wiring and connectors associated with the Boost Pressure Sensor and Fuel Pressure Sensor for problems that may result in a short circuit. Were any problems found? Yes No Repair or replace wiring/connectors as necessary. Perform ROAD TEST VERIFICATION - VER-2. Go To 3
Turn the ignition off. Disconnect the Boost Pressure Sensor and Fuel Pressure Sensor harness connectors. Disconnect the ECM harness connectors. Remove the Engine Control Relay. Connect a jumper wire between cavity 30 and cavity 87 of the Engine Control Relay connector in Fuse Block No.1. Turn the ignition on. Measure the voltage at all circuits in the Fuel Pressure Sensor and Boost Pressure Sensor harness connector cavities. Is the voltage above 1.0 volt for any of the measurements? Yes Repair the circuit(s) that measured above 1.0 volt for a short to voltage. Perform ROAD TEST VERIFICATION - VER-2. Go To 4 198
All
No
TEST 4 ACTION Turn the ignition off. Disconnect the Fuel Pressure Sensor harness connector. Turn the ignition on. With the DRBIII , erase ECM DTCs. Turn the ignition off for 10 seconds. Turn the ignition on. With the DRBIII , read ECM DTCs. Does the DRB display this DTC? Yes No Go To 5
Continued
APPLICABILITY All
Replace the Fuel Pressure Sensor in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Disconnect the Boost Pressure Sensor harness connector. Turn the ignition on. With the DRBIII , erase ECM DTCs. Turn the ignition off for 10 seconds. Turn the ignition on. With the DRBIII , read ECM DTCs. Does the DRB display this DTC? Yes Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Replace the Boost Pressure Sensor. Perform ROAD TEST VERIFICATION - VER-2.
No 6
All
199
POSSIBLE CAUSES BOOST PRESSURE SENSOR FUEL PRESSURE SENSOR VISUAL WIRING AND CONNECTOR INSPECTION INTERMITTENT CONDITION SENSOR SUPPLY VOLTAGE 2 SHORTED TO GROUND BOOST PRESSURE SENSOR SIGNAL CIRCUIT SHORTED TO SENSOR GROUND CIRCUIT ENGINE CONTROL MODULE FUEL PRESSURE SENSOR SIGNAL CIRCUIT SHORTED TO SENSOR GROUND CIRCUIT
Turn the ignition off. Visually inspect the wiring and connectors associated with the Boost Pressure Sensor and Fuel Pressure Sensor for problems that may result in a short circuit. Were any problems found? Yes No Repair or replace wiring/connectors as necessary. Perform ROAD TEST VERIFICATION - VER-2. Go To 3
Turn the ignition off. Disconnect the Boost Pressure Sensor and Fuel Pressure Sensor harness connectors. Disconnect the ECM harness connectors. Measure the resistance between ground and all of the Fuel Pressure Sensor and Boost Pressure Sensor harness connector cavities. Is the voltage below 1000 ohms for any of the measurements? Yes Repair the circuit(s) that measured below 1000 ohms for a short to ground. Perform ROAD TEST VERIFICATION - VER-2. Go To 4
All
No
200
TEST 4 ACTION Turn the ignition off. Disconnect the Fuel Pressure Sensor harness connector. Disconnect the ECM harness connectors. Measure the resistance between the Sensor Ground circuit and the Fuel Pressure Sensor Signal circuit at the Fuel Pressure Sensor harness connector. Is the resistance above 1000 ohms? Yes No Go To 5
Continued
APPLICABILITY All
Repair the Fuel Pressure Sensor Signal circuit for a short to the Sensor Ground circuit. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Disconnect the Boost Pressure Sensor harness connector. Disconnect the ECM harness connectors. Measure the resistance between the Sensor Ground circuit and the Boost Pressure Sensor Signal circuit at the Boost Pressure Sensor harness connector. Is the resistance above 1000 ohms? Yes No Go To 6
Repair the Boost Pressure Sensor Signal circuit for a short to the Sensor Ground circuit. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Disconnect the Boost Pressure Sensor harness connector. Turn the ignition on. With the DRBIII , erase ECM DTCs. Turn the ignition off for 10 seconds. Turn the ignition on. With the DRBIII , read ECM DTCs. Does the DRB display this DTC? Yes No Go To 7
Replace the Boost Pressure Sensor. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Disconnect the Fuel Pressure Sensor harness connector. Turn the ignition on. With the DRBIII , erase ECM DTCs. Turn the ignition off for 10 seconds. Turn the ignition on. With the DRBIII , read ECM DTCs. Does the DRB display this DTC? Yes Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Replace the Fuel Pressure Sensor. Perform ROAD TEST VERIFICATION - VER-2.
No
201
Continued
APPLICABILITY All
202
POSSIBLE CAUSES ENGINE OIL SENSOR INTAKE AIR PRESSURE SENSOR VISUAL WIRING AND CONNECTOR INSPECTION INTERMITTENT CONDITION SENSOR SUPPLY VOLTAGE 3 SHORTED TO GROUND ENGINE CONTROL MODULE ENGINE OIL SENSOR SIGNAL CIRCUIT SHORTED TO SENSOR GROUND CIRCUIT INTAKE AIR PRESSURE SENSOR SIGNAL CIRCUIT SHORTED TO SENSOR GROUND CIRCUIT
Turn the ignition off. Visually inspect the wiring and connectors associated with the Intake Air Pressure Sensor and Engine Oil Sensors for problems that may result in a short circuit. Were any problems found? Yes No Repair or replace wiring/connectors as necessary. Perform ROAD TEST VERIFICATION - VER-2. Go To 3
Turn the ignition off. Disconnect the Intake Air Pressure Sensor and Engine Oil Sensor harness connectors. Disconnect the ECM harness connectors. Measure the resistance between ground and all of the EOS and Intake Air Pressure Sensor harness connector cavities. Is the voltage below 1000 ohms for any of the measurements? Yes Repair the circuit(s) that measured below 1000 ohms for a short to ground. Perform ROAD TEST VERIFICATION - VER-2. Go To 4 203
All
No
TEST 4 ACTION Turn the ignition off. Disconnect the Engine Oil Sensor harness connector. Disconnect the ECM harness connectors. Measure the resistance between the Sensor Ground circuit and the Engine Oil Sensor Signal circuit at the Engine Oil Sensor harness connector. Is the resistance above 1000 ohms? Yes No Go To 5
Continued
APPLICABILITY All
Repair the Engine Oil Sensor Signal circuit for a short to the Sensor Ground circuit. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Disconnect the Intake Air Pressure Sensor harness connector. Disconnect the ECM harness connectors. Measure the resistance between the Sensor Ground circuit and the Intake Air Pressure Sensor Signal circuit at the Intake Air Pressure Sensor harness connector. Is the resistance above 1000 ohms? Yes No Go To 6
Repair the Intake Air Pressure Sensor Signal circuit for a short to the Sensor Ground circuit. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Disconnect the Intake Air Pressure Sensor harness connector. Turn the ignition on. With the DRBIII , erase ECM DTCs. Turn the ignition off for 10 seconds. Turn the ignition on. With the DRBIII , read ECM DTCs. Does the DRB display this DTC? Yes No Go To 7
Replace the Intake Air Pressure Sensor. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Disconnect the Engine Oil Sensor harness connector. Turn the ignition on. With the DRBIII , erase ECM DTCs. Turn the ignition off for 10 seconds. Turn the ignition on. With the DRBIII , read ECM DTCs. Does the DRB display this DTC? Yes Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Replace the Engine Oil Sensor. Perform ROAD TEST VERIFICATION - VER-2.
No
204
Continued
APPLICABILITY All
205
POSSIBLE CAUSES EO SENSOR INTAKE AIR PRESSURE SENSOR VISUAL WIRING AND CONNECTOR INSPECTION INTERMITTENT CONDITION SENSOR SUPPLY VOLTAGE 3 SHORTED TO VOLTAGE ENGINE CONTROL MODULE
Turn the ignition off. Visually inspect the wiring and connectors associated with the Intake Air Pressure Sensor and Engine Oil Sensors for problems that may result in a short circuit. Were any problems found? Yes No Repair or replace wiring/connectors as necessary. Perform ROAD TEST VERIFICATION - VER-2. Go To 3
206
TEST 3 ACTION Turn the ignition off. Disconnect the Intake Air Pressure Sensor and Engine Oil Sensor harness connectors. Disconnect the ECM harness connectors. Remove the Engine Control Relay. Connect a jumper wire between cavity 30 and cavity 87 of the Engine Control Relay connector in Fuse Block No.1. Turn the ignition on. Measure the voltage at all circuits in the Engine Oil Sensor and Intake Air Pressure Sensor harness connector cavities. Is the voltage above 1.0 volt for any of the measurements? Yes Repair the circuit(s) that measured above 1.0 volt for a short to voltage. Perform ROAD TEST VERIFICATION - VER-2. Go To 4 All
Continued
APPLICABILITY All
No 4
Turn the ignition off. Disconnect the Engine Oil Sensor harness connector. Turn the ignition on. With the DRBIII , erase ECM DTCs. Turn the ignition off for 10 seconds. Turn the ignition on. With the DRBIII , read ECM DTCs. Does the DRB display this DTC? Yes No Go To 5
Replace the Engine Oil Sensor. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Disconnect the Intake Air Pressure Sensor harness connector. Turn the ignition on. With the DRBIII , erase ECM DTCs. Turn the ignition off for 10 seconds. Turn the ignition on. With the DRBIII , read ECM DTCs. Does the DRB display this DTC? Yes Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Replace the Intake Air Pressure Sensor. Perform ROAD TEST VERIFICATION - VER-2.
No
207
Continued
APPLICABILITY All
208
Symptom List: P2333-S/C VEHICLE SPEED PLAUSIBILITY P2338-S/C EXCESSIVE ACCELERATION P2338-S/C EXCESSIVE DECELERATION
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P2333-S/C VEHICLE SPEED PLAUSIBILITY.
POSSIBLE CAUSES BRAKE SWITCH VERIFICATION CAB DTCS OPEN CAN BUS CIRCUITS VERIFY CAB COMMUNICATION WHEEL SPEED VERIFICATION INTERMITTENT CONDITION
TEST 1 ACTION NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. With the DRBIII , erase ECM DTCs. Test drive the vehicle and attempt to duplicate the problem. With the DRB, read ECM DTCs. Did this DTC set again? Yes No 2 Go To Go To 2 7 All APPLICABILITY All
Turn the ignition on. With the DRBIII attempt to communicate with the CAB. NOTE: If there are other DTCs set with this DTC, refer to the Symptom List and repair other stored ECM DTCs before diagnosing this DTC. Is the CAB communicating with the DRB? Yes No Go To 3
Refer to the appropriate symptom in the Body Diagnostic Information. Perform ROAD TEST VERIFICATION - VER-2.
209
P2333-S/C VEHICLE SPEED PLAUSIBILITY
TEST 3 ACTION Turn the ignition on. With the DRBIII , read the CAB DTCs. Are there any CAB DTCs? Yes No 4 Refer to symptom list for problems related to CAB. Perform ROAD TEST VERIFICATION - VER-2. Go To 4 All
Continued
APPLICABILITY All
Turn the ignition off. Disconnect the CAB Module harness connector. Disconnect the ECM harness connectors. Measure the resistance of each CAN Bus circuit between the ECM harness connector and the CAB harness connector. Is the resistance below 10.0 ohms for each measurement? Yes No Go To 5
Repair the open CAN Bus circuit(s) between the ECM and the SKREEM. Perform ROAD TEST VERIFICATION - VER-2. All
With the DRBIII , perform the Wheel Speed Test of the ABS system. Were any problems found? Yes No Repair wheel speed signal problem as necessary. Perform ROAD TEST VERIFICATION - VER-2. Go To 6
Check the Brake Switch for proper operation and adjustment. Were any problems found? Yes No Adjust or replace the Brake Switch as necessary. Perform ROAD TEST VERIFICATION - VER-2. Test Complete.
All
All
210
Symptom List: P2339-ECM P2339-ECM P2339-ECM P2339-ECM
CHECKSUM ERROR #1 CHECKSUM ERROR #2 INVALID CODING INVALID DATA
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P2339-ECM CHECKSUM ERROR #1.
POSSIBLE CAUSES ENGINE CONTROL MODULE

TEST 1 ACTION NOTE: This DTC indicates that an error occurred during ECM programming. Turn the ignition on. With the DRBIII , erase ECM DTCs. Refer to the Service Information and attempt to reprogram the ECM. Perform several engine run cycles, turning the ignition off for at least 20 seconds between each engine run cycle. With the DRBIII , read the ECM DTCs. Did this DTC set again? Yes Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Test Complete. APPLICABILITY All
No
211
Symptom: P2344-KICKDOWN SWITCH PLAUSIBILITY
POSSIBLE CAUSES INTERMITTENT CONDITION

TEST 1 ACTION NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. NOTE: If there are any Accelerator Pedal Position Sensor DTCs present, repair the APP Sensor DTCs before continuing. Turn the ignition on. With the DRB, erase ECM DTCs. Turn the ignition off for 10 seconds. Test drive the vehicle. Be sure to completely depress the accelerator pedal several times to activate the Kickdown Switch. Monitor the DRB for ECM DTCs. Did this DTC set again? Yes No 2 Test Complete. Go To 2 All APPLICABILITY All
212
Symptom List: P2347-AUTOMATIC TRANSMISSION CODED AS MANUAL TRANSMISSION P2347-CAN BUS CIRCUIT INTERUPTION P2347-MANUAL TRANSMISSIO CODED AS AUTO TRANSMISSION P2347-WRITE ERROR TO EEPROM
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P2347-AUTOMATIC TRANSMISSION CODED AS MANUAL TRANSMISSION.
POSSIBLE CAUSES ENGINE CONTROL MODULE VERIFY ECM PROGRAMMING

TEST 1 ACTION Turn the Ignition on. With the DRBIII , erase the ECM DTCs. With the DRBIII , verify that the ECM is properly coded for the options and components that the vehicle is equipped with. NOTE: Reprogram the ECM with correct information if necessary. Start and idle the engine. With the DRBIII , read ECM DTCs. Did this DTC set again? Yes Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Test complete. Perform ROAD TEST VERIFICATION - VER-2. APPLICABILITY All
No
213
Symptom: P2351-ECM SUPPLY VOLTAGE TOO LOW
POSSIBLE CAUSES ECM ECM IGNITION CIRCUIT OPEN STARTER OR LIFT PUMP RELAY CIRCUIT(S) SHORTED TO GROUND INTERMITTENT CONDITION
TEST 1 ACTION NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. Turn the ignition on. With the DRB, erase ECM DTCs. Turn the ignition off for 10 seconds. Test drive the vehicle. Monitor the DRB for ECM DTCs. Did this DTC set again? Yes No 2 Go To Go To 2 4 All APPLICABILITY All
Turn the ignition off. Disconnect the ECM harness connectors. Remove the Starter Relay and disconnect the Fuel Lift Pump harness connector Measure the resistance between ground and the Starter Relay control circuit. Measure the resistance between ground and the Fuel Lift Pump Relay control circuit. Did both circuits measure above 1000 ohms? Yes No Go To 3
Repair the relay control circuit(s) that did not measure above 1000 ohms for a short to ground. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Disconnect the ECM harness connectors. Using the Service Wiring Information determine which circuits in the ECM harness connector provide Ignition Switch power to the ECM. Turn the ignition on. Using a 12-volt test light connected to ground, check each Ignition Switch Output circuits in the ECM harness connectors. Does the test light illuminate brightly for each circuit? Yes No Replace the ECM in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Repair the Ignition Supply circuit as necessary. Perform ROAD TEST VERIFICATION - VER-2.
214
P2351-ECM SUPPLY VOLTAGE TOO LOW
Continued
APPLICABILITY All
215
Symptom List: P2359-BOOST PRESSURE TOO HIGH P2359-BOOST PRESSURE TOO LOW
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P2359-BOOST PRESSURE TOO HIGH.
POSSIBLE CAUSES AIR FILTER AIR RESTRICTION CHECKING FOR AIR LEAKS INTERMITTENT CONDITION BOOST PRESSURE SERVO MOTOR TURBOCHARGER
TEST 1 ACTION NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. NOTE: Ensure all turbocharger inlet and outlet tubes are connected properly, without damage and restriction before continuing with this test. Also ensure the Boost Pressure Servo Motor and Servo Motor rod are attached and functioning properly. Turn the ignition on. With the DRBIII , erase ECM DTCs. Test drive the vehicle. Monitor the DRBIII for ECM DTCs. Did this DTC set again? Yes No 2 Go To Go To 2 6 All APPLICABILITY All
216
P2359-BOOST PRESSURE TOO HIGH
TEST 3 ACTION NOTE: Inspect all air intake and turbocharger related tubes for damage, restriction or poor connection. Any of these conditions can cause a this DTC to set. Turn the ignition off. Inspect all air intake and turbocharger related tubes and connections. Were any problems found? Yes No 4 Repair or replace as necessary. Perform ROAD TEST VERIFICATION - VER-2. Go To 4 All
Continued
APPLICABILITY All
Turn the ignition off. Remove the Intake Air Temperature Sensor. Connect smoke machine 84-04 to the Intake Air Temperature Sensor port in the intake duct and begin injecting smoke into the intake system. Observe all intake system components for evidence of smoke leakage. Is there evidence of smoke leakage? Yes No Repair or replace as necessary. Perform ROAD TEST VERIFICATION - VER-2. Go To 5
Turn the ignition off. Replace the Boost Pressure Servo Motor in accordance with the Service Information. NOTE: Ensure the ECM and Boost Pressure Servo Motor harness connectors are connected. Test drive the vehicle. With the DRB, check for this DTC to set again. Did this DTC set again? Yes Replace the Turbocharger assembly in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Replace the Boost Pressure Servo Motor. Perform ROAD TEST VERIFICATION - VER-2.
All
No 6
All
217
Symptom List: P2511-EGR VALVE SIGNAL CIRCUIT SHORTED TO GROUND P2527-EGR VALVE SIGNAL CIRCUIT OPEN CIRCUIT P2527-EGR VALVE SIGNAL CIRCUIT SHORTED TO GROUND
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P2511-EGR VALVE SIGNAL CIRCUIT SHORTED TO GROUND.
POSSIBLE CAUSES CHECKING THE ENGINE CONTROL RELAY SYSTEM INTERMITTENT CONDITION ENGINE CONTROL RELAY OUTPUT CIRCUIT OPEN EGR VALVE CONTROL CIRCUIT SHORTED TO GROUND EGR VALVE CONTROL CIRCUIT OPEN EGR SOLENOID ENGINE CONTROL MODULE
TEST 1 ACTION NOTE: If DTC P1611, P2306 or P2332 is present with this DTC, diagnose DTCs P1611, P2306 or P2332 before diagnosing this DTC. NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. Turn the ignition on. With the DRB, erase ECM DTCs. Perform several ignition cycles, turning the ignition off for at least 10 seconds between each ignition cycle. Monitor the DRB for ECM DTCs. Did this DTC set again? Yes No 2 Go To Go To 2 8 All APPLICABILITY All
218
P2511-EGR VALVE SIGNAL CIRCUIT SHORTED TO GROUND Continued
TEST 3 ACTION Turn the ignition off. Disconnect the ECM harness connectors. Connect a jumper wire between ground and the Engine Control Relay Signal circuit in ECM C2 harness connector cavity 44. Turn the ignition on. Using a 12-volt test light connected to ground, check the Fused Engine Control Relay Output circuits at the ECM C2 harness connector cavities 1, 3 and 5. Does the test light illuminate brightly for each circuit? Yes No Go To 4 APPLICABILITY All
Turn the ignition off. Disconnect the EGR Valve harness connector. Turn the ignition on. Using a 12-volt test light connected to ground, check the Engine Control Relay Output circuit in the EGR Valve harness connector. Does the test light illuminate brightly? Yes No Go To 5
Repair the Engine Control Relay Output circuit for an open. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Disconnect the EGR Valve harness connector. Disconnect the ECM harness connectors. Measure the resistance between the EGR Valve Control circuit in the EGR Valve harness connector and ground. Is the resistance above 1000 ohms? Yes No Go To 6
Repair the EGR Valve Control circuit for a short to ground. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Disconnect the EGR Valve harness connector. Disconnect the ECM harness connectors. Measure the resistance of the EGR Valve Control circuit. Is the resistance below 10.0 ohms? Yes No Go To 7
Repair the EGR Valve Control circuit for an open. Perform ROAD TEST VERIFICATION - VER-2.
219
P2511-EGR VALVE SIGNAL CIRCUIT SHORTED TO GROUND Continued
TEST 7 ACTION Turn the ignition off. Install a substitute EGR Solenoid in place of the vehicles EGR Solenoid. NOTE: Ensure the ECM and EGR Valve harness connectors are connected. Turn the ignition on. With the DRB, check for this DTC to set again. Did this DTC set again? Yes Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Replace the EGR Solenoid. Perform ROAD TEST VERIFICATION - VER-2. All APPLICABILITY All
No 8
220
Symptom List: P2514-CRANKCASE VENT HEATER OPEN CIRCUIT P2514-CRANKCASE VENT HEATER SHORTED TO GROUND P2514-CRANKCASE VENT HEATER SHORTED TO VOLTAGE
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P2514-CRANKCASE VENT HEATER OPEN CIRCUIT.
POSSIBLE CAUSES CHECKING ECM POWER AND GROUNDS CHECKING THE ENGINE CONTROL RELAY SYSTEM INTERMITTENT CONDITION CRANKCASE VENT HEATER SHORTED TO VOLTAGE CRANKCASE VENT HEATER CIRCUIT SHORTED TO GROUND CRANKCASE HEATER VENT CIRCUIT(S) OPEN CRANCASE VENT HEATER ENGINE CONTROL MODULE
TEST 1 ACTION NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. NOTE: The engine should be cold for this test to be accurate. Turn the ignition on. With the DRB, erase ECM DTCs. Perform several engine run cycles, turning the ignition off for at least 10 seconds between each engine run cycle. Monitor the DRB for ECM DTCs. Did this DTC set again? Yes No Go To Go To 2 7 APPLICABILITY All
221
P2514-CRANKCASE VENT HEATER OPEN CIRCUIT
TEST 2 ACTION Turn the ignition off. Disconnect the ECM harness connectors. Connect a jumper wire between ground and the Engine Control Relay Control circuit in ECM C2 harness connector cavity 44. Turn the ignition on. Using a 12-volt test light connected to ground, check the Fused Engine Control Relay Output circuits at the ECM C2 harness connector cavities 1, 3 and 5. Choose the appropriate result. Test light is on for all circuits. Go To 3 Test light is on for 1 or 2 circuits Repair the Engine Control Relay Output circuit(s) that did not illuminate brightly for an open. Perform ROAD TEST VERIFICATION - VER-2. Light off for all circuits. Refer to symptom Checking the ECM Power and Grounds. Perform ROAD TEST VERIFICATION - VER-2. 3 Turn the ignition off. Disconnect the Crankcase Vent Heater harness connector. Disconnect the ECM harness connectors. Measure the resistance of the both circuits between the Crankcase Vent Heater harness connector and the ECM harness connector. Is the resistance below 10.0 ohms for each measurement? Yes No 4 Go To 4 All
Continued
APPLICABILITY All
Repair the Crankcase Vent Heater circuit(s) for an open. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Disconnect the Crankcase Vent Heater harness connector. Disconnect the ECM harness connectors. Measure the resistance between ground and both of the Crankcase Vent Heater circuits. Is the resistance above 1000 ohms for each circuit? Yes No Go To 5
Repair the Crankcase Vent Heater circuit(s) for a short to ground. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Disconnect the Crankcase Vent Heater harness connector. Disconnect the ECM harness connectors. Turn the ignition on. Measure the voltage of the both Crankcase Vent Heater circuits. Is the voltage below 1.0 volt for each circuit? Yes No Go To 6
Repair the Crankcase Vent Heater circuit for a short to voltage. Perform ROAD TEST VERIFICATION - VER-2.
222
P2514-CRANKCASE VENT HEATER OPEN CIRCUIT
TEST 6 ACTION Turn the ignition off. Install a substitute Crankcase Vent Heater in place of the vehicles existing Crankcase Vent Heater. NOTE: Ensure the ECM and Crankcase Vent Heater harness connectors are connected. With the engine cold, start and idle the engine. With the DRB, check for this DTC to set again. Did this DTC set again? Yes Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Replace the initial Crankcase Vent Heater. Perform ROAD TEST VERIFICATION - VER-2. All
Continued
APPLICABILITY All
No 7
223
Symptom: P2521-IMPROPER START ATTEMPT
POSSIBLE CAUSES VERIFY ACTIVE DTC ENGINE CONTROL MODULE

TEST 1 ACTION NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. NOTE: This DTC indicates that engine rotation has occurred without an ignition switch Start input. This can occurred when an attempt to start the vehicle using a push start method. NOTE: Consult with the customer to determine if a push start has been attempted. Turn the ignition on. With the DRBIII , erase ECM DTCs. Perform several engine run cycles, turning the ignition off for at least 20 seconds between each engine run cycle. With the DRBIII , read the ECM DTCs. Did this DTC set again? Yes Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Test complete. Perform ROAD TEST VERIFICATION - VER-2. APPLICABILITY All
No
224
Symptom: P2527-EGR VALVE SIGNAL CIRCUIT SHORTED TO VOLTAGE
POSSIBLE CAUSES INTERMITTENT CONDITION EGR SOLENOID EGR VALVE CONTROL SHORTED TO VOLTAGE ENGINE CONTROL MODULE - INTERNAL ENGINE CONTROL MODULE - INTERNAL SHORT TO VOLTAGE
TEST 1 ACTION NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. Turn the ignition on. With the DRB, erase ECM DTCs. Test drive the vehicle and monitor the DRB for ECM DTCs. Did this DTC set again? Yes No 2 Go To Go To 2 5 All APPLICABILITY All
Turn the ignition off. Disconnect the EGR Valve harness connector. Turn the ignition on. With the DRB, erase ECM DTCs. Monitor the DRB for ECM DTCs. Does the DRB display an EGR OPEN CIRCUIT DTC? Yes No Replace the EGR Solenoid. Perform ROAD TEST VERIFICATION - VER-2. Go To 3
Turn the ignition off. Disconnect the EGR Valve harness connector. Turn the ignition on. Measure the voltage of the EGR Valve Control circuit at the EGR Valve harness connector. Is the voltage below 0.5 volt? Yes Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Go To 4
All
No
225
P2527-EGR VALVE SIGNAL CIRCUIT SHORTED TO VOLTAGE Continued
TEST 4 ACTION NOTE: If DTC P1611 or P2306 is present with this DTC, diagnose DTCs P1611 and P2306 before diagnosing this DTC. Turn the ignition off. Disconnect the EGR Valve harness connector. Disconnect the ECM harness connectors. Remove the Engine Control Relay. Connect a jumper wire between cavity 30 and cavity 87 of the Engine Control Relay connector. Turn the ignition on. Measure the voltage of the EGR Valve Control circuit. Is the voltage below 0.5 volt? Yes Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Repair the EGR Valve Control circuit for a short to voltage. Perform ROAD TEST VERIFICATION - VER-2. All APPLICABILITY All
No 5
226
Symptom List: P2531-FUEL P2531-FUEL P2531-FUEL P2531-FUEL P2532-FUEL P2532-FUEL P2532-FUEL P2532-FUEL P2533-FUEL P2533-FUEL P2533-FUEL P2533-FUEL P2534-FUEL P2534-FUEL P2534-FUEL P2534-FUEL P2535-FUEL P2535-FUEL P2535-FUEL P2535-FUEL
INJECTOR INJECTOR INJECTOR INJECTOR INJECTOR INJECTOR INJECTOR INJECTOR INJECTOR INJECTOR INJECTOR INJECTOR INJECTOR INJECTOR INJECTOR INJECTOR INJECTOR INJECTOR INJECTOR INJECTOR
1 1 1 1 2 2 2 2 3 3 3 3 4 4 4 4 5 5 5 5
READ READ READ READ READ READ READ READ READ READ READ READ READ READ READ READ READ READ READ READ
TOO TOO TOO TOO TOO TOO TOO TOO TOO TOO TOO TOO TOO TOO TOO TOO TOO TOO TOO TOO
LARGE LARGE SMALL SMALL LARGE LARGE SMALL SMALL LARGE LARGE SMALL SMALL LARGE LARGE SMALL SMALL LARGE LARGE SMALL SMALL
Test Note:
All symptoms listed above are diagnosed using the same tests. The title for the tests will be P2531-FUEL INJECTOR 1 READ TOO LARGE.
POSSIBLE CAUSES FUEL INJECTOR INTERMITTENT CONDITION
227
P2531-FUEL INJECTOR 1 READ TOO LARGE
TEST 1 ACTION NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. NOTE: This DTC indicates an internal ECM problem except in the case of DTC P0606 where it may indicate a fuel injector problem. Using the Service Information, check the fuel injectors for leakage before replacing the ECM. Turn the ignition on. With the DRBIII , erase ECM DTCs. Perform several engine run cycles, turning the ignition off for at least 20 seconds between each engine run cycle. With the DRBIII , read the ECM DTCs. Did this DTC set again? Yes Replace the Fuel Injector identified in the DTC in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Go To 2 All
Continued
APPLICABILITY All
No 2
228
Symptom: P2606-CMP/CKP SYNCHRONIZATION ERROR
POSSIBLE CAUSES CAMSHAFT POSITION SENSOR SIGNAL PROBLEM CRANKSHAFT POSITION SENSOR SIGNAL PROBLEM DAMAGED CKP SENSOR DAMAGED CMP SENSOR OR CAMSHAFT ENGINE CONTROL MODULE GEAR ALIGNMENT PROBLEM INTERMITTENT CONDITION
TEST 1 ACTION NOTE: If the ECM detects and stores a DTC, the ECM also stores the engine/vehicle operating conditions under which the DTC was set. Some of these conditions are displayed on the DRB at the same time the DTC is displayed. NOTE: Before erasing stored DTCs, record these conditions. Attempting to duplicate these conditions may assist when checking for an active DTC. Turn the ignition on. With the DRBIII , erase the ECM DTCs. Attempt to start the engine. With the DRBIII , read the ECM DTCs. Does the DRB III display this DTC? Yes No 2 Go To Go To 3 2 All APPLICABILITY All
Turn the ignition on. With the DRBIII , erase the ECM DTCs. Test drive the vehicle. With the DRBIII , read the ECM DTCs. Does the DRB III display this DTC? Yes No Go To Go To 3 8
Refer to the Service Information to ensure the Engine Drive Gears/Sprocket are installed correctly and the camshaft and crankshaft gears are timed correctly. Turn the ignition off. Remove the CMP Sensor. Inspect the CMP Sensor for conditions such as loose mounting screws, damage or debris, also check the camshaft for cracked teeth. Is there any evidence of these conditions? Yes No Repair as necessary. Perform ROAD TEST VERIFICATION - VER-2. Go To 4
All
229
P2606-CMP/CKP SYNCHRONIZATION ERROR
TEST 4 ACTION Turn the ignition off. Remove the CKP Sensor. Inspect the CKP Sensor for conditions such as loose mounting screws, damage or debris. Is there any evidence of these conditions? Yes No 5 Repair as necessary. Perform ROAD TEST VERIFICATION - VER-2. Go To 5 All
Continued
APPLICABILITY All
Turn the ignition off. Using the DRB lab scope, backprobe the CMP Sensor Signal circuit at the CMP Sensor harness connector. Start the engine, if the engine will not start, crank the engine for several seconds while monitoring the DRB. NOTE: Refer to Charts and Graphs to view a correct CMP Sensor signal. Does the DRB display a steady clean CMP Signal pattern? Yes No Go To 6
Perform Test for DTC P2043-Camshaft Position Sensor Circuit Static Plausibility. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Using the DRB lab scope, backprobe both of the CKP Sensor Signal circuits at the CKP Sensor harness connector. NOTE: Refer to Charts and Graphs to view a correct CKP Sensor signal. Start the engine, if the engine will not start, crank the engine for several seconds while monitoring the DRB. Does the DRB display a steady clean CKP Signal pattern for each circuit? Yes No Go To 7
Perform Test for DTC P2045-Crankshaft Position Sensor Circuit Dynamic Plausibility. Perform ROAD TEST VERIFICATION - VER-2. All
Refer to the Service Information and check alignment of the camshaft sprocket, crankshaft sprocket and injection pump sprocket. Are all of the sprockets aligned correctly? Yes Replace and program the Engine Control Module in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Repair or adjust as necessary. Perform ROAD TEST VERIFICATION - VER-2.
No
230
P2606-CMP/CKP SYNCHRONIZATION ERROR
Continued
APPLICABILITY All
231
Symptom: *CHECKING THE FUEL PRESSURE SENSOR CIRCUITS
POSSIBLE CAUSES OPEN CIRCUITS

TEST 1 ACTION Turn the ignition off. Disconnect the Fuel Pressure Sensor harness connector. Disconnect the ECM harness connectors. Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or partially broken wires. Repair as necessary. Visually inspect the related wiring harness connectors. Look for broken, bent, pushed out, or corroded terminals. Repair as necessary. Measure the resistance of each of the three Fuel Pressure Sensor circuits between the ECM harness connector and the Fuel Pressure Sensor harness connector. Is the resistance below 10.0 ohms for each measurement? Yes No Test Complete. Repair open circuit(s) as necessary. Perform ROAD TEST VERIFICATION - VER-2. APPLICABILITY All
232
Symptom: *CHECKING THE FUEL PRESSURE SOLENOID CIRCUITS
POSSIBLE CAUSES FUEL PRESSURE SOLENOID RESISTANCE OPEN CIRCUITS

TEST 1 ACTION Turn the ignition off. Disconnect the Fuel Pressure Solenoid harness connector. Disconnect the ECM harness connectors. Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or partially broken wires. Repair as necessary. Visually inspect the related wiring harness connectors. Look for broken, bent, pushed out, or corroded terminals. Repair as necessary. Measure the resistance of both Fuel Pressure Solenoid circuits between the ECM harness connector and the Fuel Pressure Solenoid harness connector. Is the resistance below 10.0 ohms for both measurements? Yes No 2 Go To 2 APPLICABILITY All
Repair open circuit(s) as necessary. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Disconnect the Fuel Pressure Solenoid harness connector. Measure the resistance of the Fuel Pressure Solenoid. Is the resistance between 3.5 and 5.5 ohms? Yes No Test Complete. Replace the Fuel Pressure Solenoid. Perform ROAD TEST VERIFICATION - VER-2.
233
Symptom: *CHECKING THE FUEL QUANTITY SOLENOID CIRCUITS
POSSIBLE CAUSES OPEN CIRCUITS

TEST 1 ACTION Turn the ignition off. Disconnect the Fuel Quantity Solenoid harness connector. Disconnect the ECM harness connectors. Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or partially broken wires. Repair as necessary. Visually inspect the related wiring harness connectors. Look for broken, bent, pushed out, or corroded terminals. Repair as necessary. Measure the resistance of both Fuel Quantity Solenoid circuits between the ECM harness connector and the Fuel Quantity Solenoid harness connector. Is the resistance below 10.0 ohms for both measurements? Yes No Test Complete. Repair open circuit(s) as necessary. Perform ROAD TEST VERIFICATION - VER-2. APPLICABILITY All
234
Symptom: *CHECKING THE POWER AND GROUNDS
POSSIBLE CAUSES CHECKING THE ENGINE CONTROL RELAY SYSTEM EC RELAY OUTPUT CIRCUIT ECM GROUND CIRCUIT(S) OPEN ECM OUTPUT SHORTED - FUSE 16 ENGINE CONTROL MODULE ENGINE CONTROL RELAY ENGINE CONTROL RELAY B+ SUPPLY ENGINE CONTROL RELAY CONTROL CIRCUIT OPEN ENGINE CONTROL RELAY CONTROL CIRCUIT SHORT TO VOLTAGE ENGINE CONTROL RELAY OUTPUT CIRCUIT(S) OPEN ENGINE CONTROL RELAY OUTPUT CKT SHORTED TO GROUND FUSE #16 ENGINE CONTROL RELAY OUTPUT CKT SHORTED TO GROUND FUSE #17 IGNITION SWITCH START OUTPUT CIRCUIT OPEN IGNITION SWITCH START/RUN OUTPUT CIRCUIT OPEN SHORTED COMPONENT
TEST 1 ACTION Turn the ignition off. Disconnect the ECM harness connectors. Using a 12-volt test light connected to 12-volts, check each of the ECM ground circuits in ECM harness connector C2 cavities 2, 4 and 6. Did the test light illuminate brightly for each cavity? Yes No 2 Go To 2 APPLICABILITY All
Repair the ECM Ground circuit(s) for an open. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Disconnect the ECM harness connectors. Turn the ignition switch to the Start position. Using a 12-volt test light connected to ground, check the Fused Ignition Switch Start Output circuit in ECM C2 harness connector cavity 36. Does the test light illuminate brightly? Yes No Go To 3
Repair the Ignition Switch Start Output circuit for an open. Perform ROAD TEST VERIFICATION - VER-2.
235
*CHECKING THE POWER AND GROUNDS
TEST 3 ACTION Turn the ignition off. Disconnect the ECM harness connectors. Turn the ignition switch to the Start position. Using a 12-volt test light connected to ground, check the Fused Ignition Switch Start/Run Output circuit in ECM C2 harness connector cavity 19. Repeat the previous step with the ignition switch in the Run position. Does the test light illuminate brightly in the Start and Run positions? Yes No 4 Go To 4
Continued
APPLICABILITY All
Repair the Ignition Switch Start/Run Output circuit for an open. Perform ROAD TEST VERIFICATION - VER-2. All
Turn the ignition off. Remove the Engine Control Relay from Fuse Block No. 1. Using a 12-volt test light connected to 12-volts, check the Engine Control Relay Control circuit in the Engine Control Relay connector in Fuse Block No. 1. Turn the ignition on. Does the test light illuminate? Yes No Go To Go To 5 14
Turn the ignition off. Remove and inspect Fuse #17 from Fuse Block No.1. Is the fuse open? Yes No Go To Go To 6 8
All
Turn the ignition off. Disconnect the ECM harness connectors. Disconnect the EGR Valve harness connector. Disconnect the Boost Pressure Solenoid harness connector. Remove the Starter Relay. Remove the Lift Pump Relay. Install a good fuse in place of Fuse #17 in Fuse Block No.1 Connect a jumper wire between ground and the Engine Control Relay Control circuit in ECM C2 harness connector cavity 44. Turn the ignition on. Remove and inspect Fuse #17 in Fuse Block No. 1. Is the fuse open? Yes Repair the Engine Control relay Output circuit for a short to ground. Perform ROAD TEST VERIFICATION - VER-2. Go To 7
All
No 7
NOTE: A short circuit exists in one of the following: Lift Pump Relay, Starter Relay, EGR Valve, Boost Pressure Servo Motor or ECM. View repair. Yes Using the Service Information wiring check the listed components for short circuits. Replace the shorted component as necessary. Perform ROAD TEST VERIFICATION - VER-2.
All
236
TEST 8 ACTION Turn the ignition off. Remove and inspect Fuse #16 from Fuse Block No.1 Is the fuse open? Yes No 9 Go To Go To 9 11 All
Continued
APPLICABILITY All
Turn the ignition off. Disconnect the ECM harness connectors. Install a good fuse in place of Fuse #16 in Fuse Block No.1 Connect a jumper wire between ground and the Engine Control Relay Control circuit in ECM C2 harness connector cavity 44. Remove and inspect Fuse #16 from Fuse Block No.1. Is the fuse open? Yes Repair the Engine Control Relay Output circuit for a short to ground. Perform ROAD TEST VERIFICATION - VER-2. Go To 10
No 10
The Fuel Injectors, Crankcase Heater, Water In Fuel Sensor and related circuits can cause Fuse #16 in Fuse Block No.1 to open. Use the Service Information Wiring Diagrams and check these circuits/components for shorted circuits. Were any problems found. Yes No Repair or replace shorted circuit/component as necessary. Perform ROAD TEST VERIFICATION - VER-2. Replace and program the ECM in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2.
All
11
Turn the ignition off. Disconnect the ECM harness connectors. Connect a jumper wire between ground and the Engine Control Relay Control circuit in ECM C2 harness connector cavity 44. Turn the ignition on. Using a 12-volt test light connected to ground, check the Fused Engine Control Relay Output circuits at the ECM C2 harness connector cavities 1, 3 and 5. Choose the appropriate result. Test light is on for all circuits. Test Complete. Test light is on for 1 or 2 circuits Repair the Engine Control Relay Output circuit(s) for an open. Perform ROAD TEST VERIFICATION - VER-2. Light off for all circuits. Go To 12
All
237
TEST 12 ACTION Turn the ignition off. Substitute the Engine Control Relay with a known good relay. Disconnect the ECM harness connectors. Connect a jumper wire between ground and the Engine Control Relay Signal circuit in ECM C2 harness connector cavity 44. Turn the ignition on. Using a 12-volt test light connected to ground, check the Fused Engine Control Relay Output circuits at the ECM C2 harness connector cavities 1, 3 and 5. Does the test light illuminate brightly? Yes No 13 Replace the initial Engine Control Relay. Perform ROAD TEST VERIFICATION - VER-2. Go To 13 All
Continued
APPLICABILITY All
Turn the ignition off. Remove the Engine Control Relay from Fuse Block No.1 Using a 12-volt test light connected to ground, check both Battery (+) circuits at the Engine Control Relay connector in Fuse Block No.1 Does the test light illuminate brightly for each circuit? Yes Repair the Engine Control Relay Output circuit for an open between the Engine Control Relay connector in Fuse Block No. 1 and ECM C2 harness connector cavities 1, 3 and 5. It may be necessary to replace the Fuse Block No. 1 to repair this circuit. Perform ROAD TEST VERIFICATION - VER-2. Repair the Battery (+) Supply circuits to the Engine Control Relay. Perform ROAD TEST VERIFICATION - VER-2.
No
14
Turn the ignition off. Remove the Engine Control Relay from Fuse Block No. 1. Disconnect the ECM harness connectors. Measure the resistance of the Engine Control Relay Control circuit. Is the resistance below 10.0 ohms? Yes No Go To 15
All
Repair the Engine Control Relay Control circuit for an open. Perform ROAD TEST VERIFICATION - VER-2. All
15
Turn the ignition off. Remove the Engine Control Relay from Fuse Block No. 1. Disconnect the ECM harness connectors. Measure the voltage of the Engine Control Relay Control circuit. Is the voltage below 1.0 volts? Yes Replace and program the ECM in accordance with the Service Information. Perform ROAD TEST VERIFICATION - VER-2. Repair the Engine Control Relay Control circuit for a short to voltage. Perform ROAD TEST VERIFICATION - VER-2.
No
238
Symptom: *ENGINE CRANKS BUT WILL NOT START
POSSIBLE CAUSES CAMSHAFT POSITION SENSOR SIGNAL PROBLEM CRANKSHAFT POSITION SENSOR SIGNAL PROBLEM ECM CODES PRESENT ECT SENSOR ENGINE CONTROL MODULE ENGINE DRIVE GEAR/SPROCKET FUEL SUPPLY CONTAMINATION FUEL SYSTEM PRESSURE MECHANICAL FUEL SYSTEM RESTRICTION GLOW PLUGS SKIM CODES PRESENT
TEST 1 ACTION NOTE: The ECM must have proper power and ground connections for the following tests to be valid. Refer to Checking the ECM Power and Grounds in the symptom list. NOTE: A no-start condition may occur if the Fuel Temperature Sensor is shorted or if the Fuel Temperature Sensor Signal circuit is shorted to ground or shorted to Sensor Ground. Turn the ignition on. With the DRBIII , read the ECM DTCs. Does the DRBIII display any ECM DTCs? Yes No 2 Refer to symptom list for problems related to ECM DTC. Perform NO START VERIFICATION - VER-1. Go To 2 All APPLICABILITY All
Turn the ignition on. With the DRBIII , read the SKREEM DTCs. Does the DRBIII display any SKREEM DTCs? Yes No Refer to symptom list for problems related to SKIM DTC. Perform NO START VERIFICATION - VER-1. Go To 3
Using a temperature probe, check the vehicle temperature near the ECT Sensor. Turn the ignition on. With the DRBIII in Sensors, read the ECT Sensor temperature. Compare the temperature probe reading with the DRBIII reading. Are the two readings within 10C of each other? Yes No Go To 4
All
Repair as necessary. Perform NO START VERIFICATION - VER-1.
239
*ENGINE CRANKS BUT WILL NOT START
TEST 4 ACTION NOTE: Prior to performing this test, be sure to check the Glow Plug Relay operation. Refer to CHECKING GLOW PLUG OPERATION for the related symptom(s). Refer to the Service Information and check the Glow Plugs for proper operation. Are the Glow Plugs operating properly? Yes No 5 Go To 5
Continued
APPLICABILITY All
Repair as necessary. Perform NO START VERIFICATION - VER-1. All
Inspect the fuel system lines for restrictions, leaks or other problems. NOTE: Refer to the Service Information to ensure that the fuel system is properly primed. An unprimed system or excessive air in the supply system will cause a no-start condition. Is there any evidence of problems? Yes No Repair as necessary. Perform NO START VERIFICATION - VER-1. Go To 6
Refer to the Service Information and perform the fuel pressure test. Is the fuel pressure within specification? Yes No Go To 7
All
Repair as necessary. Perform NO START VERIFICATION - VER-1. All
Inspect the fuel supply for contamination. Is the fuel contaminated? Yes Refer to the Service Information to remove and replace fuel throughout the fuel system. Perform NO START VERIFICATION - VER-1. Go To 8
No 8
Turn the ignition off. Using the DRBIII lab scope, backprobe the CMP Sensor Signal circuit at the ECM harness connector. Start the engine, if the engine will not start, crank the engine for several seconds while monitoring the DRBIII . NOTE: Refer to Charts and Graphs to view a correct CMP Sensor signal. Does the DRBIII display a steady clean CMP Signal pattern? Yes No Go To 9
All
Perform Test for DTC P2043-Camshaft Position Sensor Circuit Static Plausibility. Perform NO START VERIFICATION - VER-1.
240
*ENGINE CRANKS BUT WILL NOT START
TEST 9 ACTION Turn the ignition off. Using the DRBIII lab scope, backprobe both of the CKP Sensor Signal circuits at the ECM harness connector. NOTE: Refer to Charts and Graphs to view a correct CKP Sensor signal. Start the engine, if the engine will not start, crank the engine for several seconds while monitoring the DRBIII . Does the DRBIII display a steady clean CKP Signal pattern for each circuit? Yes No Go To 10
Continued
APPLICABILITY All
Perform Test for DTC P2045-Crankshaft Position Sensor Circuit Dynamic Plausibility. Perform NO START VERIFICATION - VER-1. All
10
Refer to the Service Information to ensure the Engine Drive Gears/Sprocket are installed correctly and the camshaft and crankshaft gears are timed correctly. Were any problems found? Yes No Repair as necessary. Perform NO START VERIFICATION - VER-1. Replace and program the Engine Control Module in accordance with the Service Information. Perform NO START VERIFICATION - VER-1.
241
Symptom: *ENGINE WILL NOT CRANK
POSSIBLE CAUSES BATTERY CABLE HIGH RESISTANCE BATTERY CABLES CHECKING ECM POWER AND GROUNDS CHECKING FOR TCM CODES ECM ECM CODES PRESENT IGNITION SWITCH OUTPUT (START) CIRCUIT OPEN MECHANICAL PROBLEM SKREEM CODES PRESENT STARTER MOTOR STARTER MOTOR RELAY STARTER MOTOR RELAY CIRCUIT(S) OPEN STARTER MOTOR RELAY CIRCUIT(S) SHORTED TO GROUND STARTER RELAY CONTROL CIRCUIT SHORTED TO VOLTAGE STARTER RELAY OUTPUT CIRCUIT OPEN
TEST 1 ACTION Turn the ignition off. NOTE: The battery must be fully charged before diagnosing a no crank condition. Inspect the battery cables for corrosion, looseness or other problems. Is there evidence of problems? Yes No 2 Repair as necessary. Perform NO START VERIFICATION - VER-1. Go To 2 All APPLICABILITY All
Turn the ignition off. Remove the Starter Motor Relay from the Fuse/Relay Block. Connect a test light between cavities 85 and 86 of the Starter Motor Relay connector in the Fuse/Relay Block connector. While observing the test light, attempt to start the engine. Did the test light illuminate when turning the ignition switch to the Crank position? Yes No Go To Go To 3 8
242
*ENGINE WILL NOT CRANK
TEST 3
Continued
APPLICABILITY All
ACTION Turn the ignition off. Remove the Starter Motor Relay from the Fuse/Relay Block. Using a 12-volt test light connected to ground, check the Ignition Switch Output (Start) circuit in the Starter Motor Relay connector in the Fuse/Relay Block while turning the ignition to the Crank/Start position. Did the test light illuminate while turning the ignition to the Crank/Start position? Yes No Go To 4
Repair the Ignition Switch Output (Start) circuit for an open. Perform NO START VERIFICATION - VER-1. All
Turn the ignition off. Remove the Starter Motor Relay from the Fuse/Relay Block. Install a substitute relay in place of the Starter Motor Relay. Attempt to start the engine. Does the engine crank? Yes No Replace the Starter Motor Relay. Perform NO START VERIFICATION - VER-1. Go To 5
Turn the ignition off. Remove the Starter Motor Relay from the Fuse/Relay Block. Disconnect the Starter Motor Relay Output wire from the Starter Solenoid. Connect the Starter Motor Relay Output wire (at the Starter) to ground. Using a 12-volt test light connected to 12-volts, check the Starter Motor Relay Output circuit at the Starter Motor Relay connector in the Fuse/Relay Block. Does the test light illuminate brightly? Yes No Go To 6
All
Repair the Starter Relay Output circuit for an open. Perform NO START VERIFICATION - VER-1. All
Using the Service Information, check the battery cables for high resistance. Did either battery cable have a voltage drop greater than 0.2 volts? Yes No Replace the battery cable(s). Perform NO START VERIFICATION - VER-1. Go To 7
Turn the ignition off. Attempt to manually rotate the crankshaft 360. Is the crankshaft able to rotate 360? Yes No Replace the Starter Motor. Perform NO START VERIFICATION - VER-1. Repair the engine mechanical problem. Perform NO START VERIFICATION - VER-1.
All
243
TEST 8
Continued
APPLICABILITY All
ACTION NOTE: The ECM must have proper power and ground connections for the following tests to be valid. Refer to Checking the ECM Power and Grounds in the symptom list. Turn the ignition on. With the DRBIII , read the ECM DTCs. Does the DRBIII display any ECM DTCs? Yes No Refer to symptom list for problems related to ECM DTC. Perform NO START VERIFICATION - VER-1. Go To 9
Turn the ignition on. With the DRBIII , read the SKREEM DTCs. Does the DRBIII display any SKREEM DTCs? Yes No Refer to symptom list for problems related to SKREEM. Perform NO START VERIFICATION - VER-1. Go To 10
All
10
Turn the ignition on. With the DRBIII , read the TCM DTCs. Does the DRBIII display any TCM DTCs? Yes No Refer to symptom list for problems related to TCM. Perform NO START VERIFICATION - VER-1. Go To 11
All
11
Perform the Checking the ECM Power and Grounds test. Were any problems found? Yes No Repair as necessary. Perform NO START VERIFICATION - VER-1. Go To 12
All
12
Turn the ignition off. Disconnect the ECM harness connectors. Remove the Starter Motor Relay from the Fuse/Relay Block Remove the Engine Control Relay from the Fuse Block No.1. Using a jumper wire, connect Engine Control Relay connector cavities 30 and 87 in the Fuse Block No.1. Turn the ignition on. Measure the voltage of the Starter Motor Relay Control circuit. Is the voltage above 1.0 volt? Yes No Repair the Starter Relay Control circuit for a short to voltage. Perform NO START VERIFICATION - VER-1. Go To 13
All
244
TEST 13
Continued
APPLICABILITY All
ACTION Turn the ignition off. Disconnect the ECM harness connectors. Remove the Starter Motor Relay from the Fuse/Relay Block. Measure the resistance of the Starter Motor Relay Control circuit between the ECM harness connector and the Fuse/Relay Block connector. Measure the resistance of the Starter Motor Relay 12-volt Supply circuit between the ECM harness connector and the Fuse/Relay Block connector. Is the resistance below 10.0 ohms for each measurement? Yes No Go To 14
Repair the Starter Motor Relay circuit(s) for an open. Perform NO START VERIFICATION - VER-1. All
14
Turn the ignition off. Disconnect the ECM harness connectors. Remove the Starter Motor Relay from the Fuse/Relay Block. Measure the resistance between ground and the Starter Motor Relay Control circuit at the Fuse/Relay Block connector. Measure the resistance between ground and the Starter Motor Relay 12-volt Supply circuit at the Fuse/Relay Block connector. Is the resistance below 10.0 ohms for each measurement? Yes Replace and program the Engine Control Module in accordance with the Service Information. Perform NO START VERIFICATION - VER-1. Repair the Starter Motor Relay circuit(s) for a short to ground. Perform NO START VERIFICATION - VER-1.
No
245
VERIFICATION TESTS
Verification Tests
BODY VERIFICATION TEST - VER 1 1. Disconnect all jumper wires and reconnect all previously disconnected components and connectors. 2. Ensure that all accessories are turned off and the battery is fully charged. 3. NOTE: Refer to the service information for proper programming procedures if the ABM; ACM; ATC; CTM; ECM; IC; SKREEM; SLA; or SSM was replaced. 4. If the SKREEM was replaced, program all RKE transmitters used with this vehicle. 5. NOTE: Perform the next 8 steps of this procedure if either diagnosing the Automatic Temperature Control (ATC) system or if repairs were made to the ATC system. All of the following criteria must be met in order to successfully run the ATC Function Test. 6. With DRBIII , record and erase ATC DTCs. 7. Place the shift lever in Park. 8. Start the engine. Allow the engine to reach normal operating temperature. 9. Set the blower to high speed. 10. Press the Air Conditioning switch On. 11. With the DRBIII , verify that the ambient temperature is above 59F (15C), the refrigerant pressure is between 29 and 348 PSI (2 and 24 bar), the evaporator temperature is above 36.5F (2.5C), and the coolant temperature is above 158F (70C). 12. With the DRBIII in ATC, select System Tests and select ATC Function Test. When the ATC Function Test is complete, proceed to the next step of this procedure. 13. With the DRBIII , read active ATC DTCs. If any DTC is active or if the original condition is still present, proceed to the conclusion question and answer Yes. 14. With the DRBIII , record and erase all DTCs from ALL modules. Start and run the engine for 2 minutes. Operate all functions of the system that caused the original concern. 15. Turn the ignition off and wait 5 seconds. Turn the ignition on and using the DRBIII , read DTCs from ALL modules. Are any DTCs present or is the original condition still present? Yes No Repair is not complete, refer to the appropriate symptom. Repair is complete. NAG1 TRANSMISSION VERIFICATION TEST - VER 1 1. Reconnect any disconnected components. 2. Connect the DRBIII to the Data Link Connector. 3. With the DRBIII , erase ABS DTCs. 4. With the DRBIII , erase ECM DTCs. 5. With the DRBIII , erase Transmission DTCs. 6. With the DRBIII , display Transmission Temperature. Start and run the engine until the Transmission Temperature is HOT, above 43 C (110 F). 7. Check the Transmission fluid and adjust if necessary. Refer to the Service Information for the proper Fluid Fill procedure. 8. NOTE: If internal repairs were performed and the shift quality is still poor, it may be necessary to check the internal repair. Also check for any TSBs and/or Controller Flash updates that may apply. 9. ROAD TEST PROCEDURE 10. Road test the vehicle. Make fifteen to twenty 1-2, 2-3, 3-4 and 4-5 upshifts. 11. Perform these shifts from a standing start to 72 km/h (45 MPH) with a constant throttle opening of 20 to 25 degrees. 12. With speeds below 40 km/h (25 MPH), make five to eight wide open throttle kickdowns to 1st gear. Allow at least 5 seconds each in 2nd and 3rd gear between each kickdown. 13. With the DRBIII , read Transmission DTCs. Were there any Diagnostic Trouble Codes set? Yes No Repair is not complete, refer to appropriate symptom. Repair is complete. APPLICABILITY All APPLICABILITY All
246
VERIFICATION TESTS
Verification Tests
Continued
APPLICABILITY All
NO START VERIFICATION - VER-1 1. NOTE: IMPORTANT! If the Engine Control Module or Sentry Key Immobilizer Module has been replaced, ensure the programming procedure for the module has been performed in accordance with the Service Information. 2. Inspect the vehicle to ensure that all engine components are properly installed and connected. Reassemble and reconnect components as necessary. 3. Inspect the engine oil for contamination. If it is contaminated, change the oil and filter. 4. With the DRB, erase all diagnostic trouble codes (DTCs). 5. Turn the ignition off for at least 10 seconds. 6. Attempt to start the engine. 7. If the engine is unable to start, look for any Technical Service Bulletins (TSBs) that may relate to this condition. Return to the Symptom List if necessary. 8. If the engine starts and continues to run, the repair is now complete. Are any DTCs or symptoms remaining? Yes No Repair is not complete, refer to appropriate symptom. Repair is complete. ROAD TEST VERIFICATION - VER-2 1. Inspect the vehicle to ensure that all engine components are properly installed and connected. Reassemble and reconnect components as necessary. 2. If this verification procedure is being performed after a non-DTC test, perform steps 3 and 4. If not, proceed to step 5. 3. Check to see if the initial symptom still exists. If there are no trouble codes and the symptom no longer exists, the repair was successful and testing is now complete. 4. If the initial or another symptom exists, the repair is not complete. Check all pertinent Technical Service Bulletins (TSBs) and return to the Symptom List if necessary. 5. For previously read DTCs that have not been dealt with, return to the Symptom List and follow the diagnostic path for that DTC; otherwise, continue. 6. If the Engine Control Module (ECM) has not been changed, perform steps 7 and 8, otherwise, continue with step 9. 7. With the DRB III , erase all diagnostic trouble codes (DTCs), then disconnect the DRB III . 8. Turn the ignition off for at least 10 seconds. 9. If equipped with a Transfer Case Position Switch, perform step 10, otherwise, continue with step 11. 10. With the ignition switch on, place the Transfer Case Shift Lever in each gear position, stopping for 15 seconds in each position. 11. Ensure no DTCs remain by performing steps 12 through 15. 12. Road test the vehicle. For some of the road test, go at least 64 km/h (40 MPH). If this test is for an A/C Relay Control Circuit, drive the vehicle for at least 5 minutes with the A/C on. 13. At some point, stop the vehicle and turn the engine off for at least 10 seconds, then restart the engine and continue. 14. Upon completion of the road test, turn the engine off and check for DTCs with the DRB III . 15. If the repaired DTC has set again, the repair is not complete. Check for any pertinent Technical Service Bulletins (TSBs) and return to the Symptom List. If there are no DTCs, the repair was successful and is now complete. Are any DTCs or symptoms remaining? Yes No Repair is not complete, refer to appropriate symptom. Repair is complete.
APPLICABILITY All
247
NOTES
248
COMPONENT LOCATIONS
8.0 8.1 COMPONENT LOCATIONS CONTROL MODULES
C O M P O N E N T L O C A T I O N S
8.2
CONTROLS AND SOLENOIDS
249
COMPONENT LOCATIONS
8.2 CONTROLS AND SOLENOIDS (Continued)
8.3
DATA LINK CONNECTOR
250
COMPONENT LOCATIONS
8.4 SENSORS
251
COMPONENT LOCATIONS
8.4 SENSORS (Continued)
252
COMPONENT LOCATIONS
8.5 SWITCHES
253
NOTES
254
CONNECTOR PINOUTS
9.0 CONNECTOR PINOUTS
ACCELERATOR PEDAL POSITION SENSOR (OBD)
CAV 1 2 3 4 5 18BL/DG 18BR/GY 18GY/DG 18BL/RD 18BR/BL CIRCUIT FUNCTION ACCEL PEDAL POSITION SENSOR SIGNAL NO. 1 ACCEL PEDAL POSITION SENSOR GROUND NO. 2 ACCEL PEDAL POSITION SENSOR SIGNAL NO. 2 ACCEL PEDAL POSITION SENSOR 5 VOLT SUPPLY ACCEL PEDAL POSITION SENSOR GROUND NO. 1
AIRBAG CONTROL MODULE - YELLOW

CAV 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 20DG 20BL/DG 20BR/DG 20BK/RD 20DG 20VT 20BL 20BR/YL 20BL 20BR 20BK 20BR 20YL K-ACM DRIVER AIRBAG SQUIB 1 LINE 2 DRIVER AIRBAG SQUIB 1 LINE 1 PASSENGER AIRBAG SQUIB 1 LINE 2 PASSENGER AIRBAG SQUIB 1 LINE 1 ENHANCED ACCIDENT REPORT DRIVER CIRCUIT FUNCTION DRIVER SEAT BELT TENSIONER LINE 2 DRIVER SEAT BELT TENSIONER LINE 1 PASSENGER SEAT BELT TENSIONER LINE 2 PASSENGER SEAT BELT TENSIONER LINE 1 FUSED IGNITION SWITCH OUTPUT (RUN-START) GROUND AIRBAG WARNING INDICATOR DRIVER -
C O N N E C T O R P I N O U T S
BOOST PRESSURE SENSOR (OBD)

CAV 1 2 3 18BR/WT 18WT/DG 18WT/RD CIRCUIT SENSOR GROUND BOOST PRESSURE SENSOR SIGNAL BOOST PRESSURE SENSOR 5 VOLT SUPPLY FUNCTION
255
CONNECTOR PINOUTS
BOOST PRESSURE SERVOMOTOR (OBD)
CAV 1 2 3 4 5 16YL/DG 16YL/BK 16YL/WT CIRCUIT GROUND BOOST PRESSURE SERVOMOTOR CONTROL FUNCTION FUSED ENGINE CONTROL RELAY OUTPUT
CAMSHAFT POSITION SENSOR - BLACK

CAV 1 2 3 3 20BR/DG 20YL/GY 18RD/BL (EXCEPT OBD) 20RD/BL (OBD) CIRCUIT FUNCTION CAMSHAFT POSITION SENSOR GROUND CAMSHAFT POSITION SENSOR SIGNAL CAMSHAFT POSITION SENSOR 12 VOLT SUPPLY CAMSHAFT POSITION SENSOR 5 VOLT SUPPLY
256
CONNECTOR PINOUTS
CONTROLLER ANTILOCK BRAKE
CAV 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 20RD/BL 20DG 20DG/YL 20WT/RD 18BK/RD 20DG/WT 20BR 20WT/GY 18BK/BL 18BR 20BR 20BR 20YL 18BK/RD POWER INPUT CAN C BUS (-) SENSOR SIGNAL 5 VOLT SUPPLY 20WT 20BR CAN C BUS (+) SENSOR GROUND BRAKE PRESSURE SENSOR SIGNAL TCS SWITCH (ASR) SENSE LEFT FRONT WHEEL SPEED SENSOR (-) LEFT REAR WHEEL SPEED SENSOR (-) RIGHT REAR WHEEL SPEED SENSOR (-) RIGHT REAR WHEEL SPEED SENSOR (+) BRAKE LAMP SWITCH OUTPUT 20WT 18BR 18BK BRAKE SWITCH OUTPUT GROUND FUSED OPTIONAL EQUIPMENT RELAY OUTPUT 20BK/DG 20YL/WT 20YL/RD 18BL/BK 18BK 14BR 14RD SENSOR SIGNAL SENSOR SIGNAL SENSOR SIGNAL K-ABS/SHIFTER ASSEMBLY LEFT FRONT WHEEL SPEED SENSOR (+) LEFT REAR WHEEL SPEED SENSOR (+) RIGHT FRONT WHEEL SPEED SENSOR (-) RIGHT FRONT WHEEL SPEED SENSOR (+) 12BR 12RD GROUND FUSED B(+) CIRCUIT GROUND FUSED B(+) FUNCTION
CRANKCASE HEATER - BLACK

CAV 1 1 2 2 CIRCUIT 18BR (EXCEPT OBD) 18BK/RD (OBD) 16BK/RD (EXCEPT OBD) 18BK/BR (OBD) GROUND CRANKCASE HEATER SIGNAL FUSED ENGINE CONTROL RELAY OUTPUT CRANKCASE HEATER GROUND FUNCTION
257
CONNECTOR PINOUTS
CRANKSHAFT POSITION SENSOR - BLACK

CAV 1 1 2 2 CIRCUIT 20DG (EXCEPT OBD) 20DG/WT (OBD) 20DG/WT (EXCEPT OBD) 20DG (OBD) FUNCTION CRANKSHAFT POSITION SENSOR SIGNAL NO. 2 CRANKSHAFT POSITION SENSOR SIGNAL NO. 1 CRANKSHAFT POSITION SENSOR SIGNAL NO. 1 CRANKSHAFT POSITION SENSOR SIGNAL NO. 2
DATA LINK CONNECTOR - BLACK

CAV 1 2 3 4 5 6 7 20BL/YL 20BK/BL/DG 20BL/BK 20BL 20GY/DG/RD 20BK/RD 20WT/GY 20RD/YL K-IC/ATC/HBM/CHM FUSED B(+) K-TCM/RADIO K-CTM/SSM K-ACM 8 9 10 11 12 13 14 15 16 20DG/YL 20BR 20BR K-ECM FUSED IGNITION SWITCH OUTPUT (RUN-START) K-ABS/SHIFTER ASSEMBLY 20WT/DG ENGINE RPM GROUND GROUND CIRCUIT K-SKREEM FUNCTION
EGR VALVE - BLACK

CAV 1 1 2 2 3 3 4 CIRCUIT 20RD/YL (EXCEPT OBD) 20DG/WT (OBD) 16BK/GY (EXCEPT OBD) 16BK/DG (OBD) 18BR/BK (EXCEPT OBD) 20BR/DG (OBD) EGR VALVE CONTROL EGR VALVE CONTROL FUSED ENGINE CONTROL RELAY OUTPUT FUSED ENGINE CONTROL RELAY OUTPUT SENSOR GROUND SENSOR GROUND FUNCTION
258
CONNECTOR PINOUTS
ENGINE CONTROL MODULE C1 (OBD)
CAV 1 2 3 4 8 10 11 12 13 14 15 20 21 25 26 28 31 32 35 36 37 38 39 40 49 50 51 52 55 56 57 59 61 62 72 73 74 76 79 84 85 86 87 88 90 91 93 16BL 16BL/WT 16DG 20RD/WT 18BL/GY 20RD/YL 20GY/BL 20BR/RD 20VT/DG 20BR/DG 20DG/BK 18BK/YL 18BK/RD 16BK 16BK/WT 18RD/BK 20YL/BL 18DG/BK 20BR/BK 20VT/RD 20RD/BL 20YL/GY 20GY 20GY/WT 16BK/VT 16BK/DG 16BK/YL 20BK/WT 18BR 20BR/WT 20DG/RD 20DG/VT 20BR/VT 20DG/YL 20GY/BL 16BK/RD 16BK/BL 18BR/YL 18BR/RD 20BR/GY 20YL/DG 20RD/DG 20DG/WT 20DG 20DG/WT 18BK/BR 16YL/DG CIRCUIT FUNCTION FUEL INJECTOR NO. 1 HIGH-SIDE CONTROL FUEL INJECTOR NO. 4 HIGH-SIDE CONTROL FUEL INJECTOR NO. 3 HIGH-SIDE CONTROL FUEL PRESSURE SOLENOID 12 VOLT SUPPLY FUEL TEMPERATURE SENSOR SIGNAL ENGINE OIL SENSOR 5 VOLT SUPPLY ENGINE OIL SENSOR SIGNAL INTAKE PRESSURE SENSOR GROUND INTAKE PRESSURE SENSOR SIGNAL CAMSHAFT POSITION SENSOR GROUND O2 1/1 PUMP CELL SIGNAL WATER IN FUEL SENSOR SIGNAL CRANKCASE HEATER SIGNAL FUEL INJECTOR NO. 2 HIGH-SIDE CONTROL FUEL INJECTOR NO. 5 HIGH-SIDE CONTROL FUEL QUANTITY SOLENOID 12 VOLT SUPPLY MASS AIR FLOW SENSOR GROUND FUEL TEMPERATURE SENSOR GROUND SENSOR GROUND INTAKE PRESSURE SENSOR 5 VOLT SUPPLY CAMSHAFT POSITION SENSOR 5 VOLT SUPPLY CAMSHAFT POSITION SENSOR SIGNAL O2 1/1 SENSOR CELL SIGNAL O2 1/1 VIRTUAL GROUND FUEL INJECTOR NO. 4 LOW-SIDE CONTROL FUEL INJECTOR NO. 3 LOW-SIDE CONTROL FUEL INJECTOR NO. 5 LOW-SIDE CONTROL FUEL PRESSURE SOLENOID CONTROL WATER IN FUEL SENSOR GROUND ENGINE COOLANT TEMPERATURE SENSOR GROUND ENGINE COOLANT TEMPERATURE SENSOR SIGNAL FUEL PRESSURE SENSOR SIGNAL MASS AIR FLOW SENSOR 5 VOLT SUPPLY O2 1/1 PUMP CELL CONTROL O2 1/1 HEATER CONTROL FUEL INJECTOR NO. 1 LOW-SIDE CONTROL FUEL INJECTOR NO. 2 LOW-SIDE CONTROL FUEL QUANTITY SOLENOID CONTROL WATER IN FUEL SENSOR 12 VOLT SUPPLY FUEL PRESSURE SENSOR GROUND MASS AIR FLOW SENSOR SIGNAL FUEL PRESSURE SENSOR 5 VOLT SUPPLY CRANKSHAFT POSITION SENSOR SIGNAL NO. 1 CRANKSHAFT POSITION SENSOR SIGNAL NO. 2 EGR VALVE CONTROL CRANKCASE HEATER GROUND BOOST PRESSURE SERVOMOTOR CONTROL
259
CONNECTOR PINOUTS
ENGINE CONTROL MODULE C2 (OBD)
CAV 1 2 3 4 5 6 7 8 10 11 12 13 14 17 18 19 24 25 26 28 31 32 36 37 38 42 43 44 50 51 52 53 54 55 58 16BK/RD 14BR 14BK/BL 14BR 14BK/BL 14BR 18RD 18BR/WT 18WT/RD 18WT/DG 18BR/WT 18GY/DG 18BR/GY 18BR/DG 20DG/YL 18BK 18BL/RD 18BL/DG 18BR/BL 18BR/DG 20BL/YL 20DG 18VT 18DG 18BK 18DG/WT 18BK/RD 18YL/BL 18YL 18GY 18BL 20DG/WT 20DG 18BR/RD 18VT/DG CIRCUIT GROUND FUSED ENGINE CONTROL RELAY OUTPUT GROUND FUSED ENGINE CONTROL RELAY OUTPUT GROUND S/C SWITCH 12 VOLT SUPPLY HIGH IDLE ON SIGNAL BOOST PRESSURE SENSOR 5 VOLT SUPPLY BOOST PRESSURE SENSOR SIGNAL SENSOR GROUND ACCEL PEDAL POSITION SENSOR SIGNAL NO. 2 ACCEL PEDAL POSITION SENSOR GROUND NO. 2 KICKDOWN SWITCH SIGNAL ENGINE RPM FUSED IGNITION SWITCH OUTPUT (RUN-START) ACCEL PEDAL POSITION SENSOR 5 VOLT SUPPLY ACCEL PEDAL POSITION SENSOR SIGNAL NO. 1 ACCEL PEDAL POSITION SENSOR GROUND NO. 1 INTAKE AIR TEMPERATURE SENSOR GROUND K-ECM ENHANCED ACCIDENT REPORT DRIVER IGNITION SWITCH OUTPUT (START) ACCEL/SET SIGNAL VERIFICATION SIGNAL INTAKE AIR TEMPERATURE SENSOR SIGNAL GLOW PLUG MODULE CONTROL ENGINE CONTROL RELAY CONTROL DECEL/SET SIGNAL OFF SIGNAL RESUME SIGNAL CAN C BUS (+) CAN C BUS (-) FUEL PUMP RELAY CONTROL STARTER MOTOR RELAY CONTROL FUNCTION FUSED ENGINE CONTROL RELAY OUTPUT
ENGINE COOLANT TEMPERATURE SENSOR - BLACK

CAV 1 2 20BR/WT 20DG/RD CIRCUIT FUNCTION ENGINE COOLANT TEMPERATURE SENSOR GROUND ENGINE COOLANT TEMPERATURE SENSOR SIGNAL
260
CONNECTOR PINOUTS
ENGINE OIL SENSOR - BLACK

CAV 1 2 3 20GY/BL 20BR/BK 20RD/YL CIRCUIT SENSOR GROUND ENGINE OIL SENSOR 5 VOLT SUPPLY FUNCTION ENGINE OIL SENSOR SIGNAL
FUEL INJECTOR NO. 1 - BLACK

CAV 1 1 2 2 CIRCUIT 14BK/BL (EXCEPT OBD) 16BK/RD (OBD) 14BK (EXCEPT OBD) 16BL (OBD) FUNCTION FUEL INJECTOR NO. 1 CONTROL FUEL INJECTOR NO. 1 LOW-SIDE CONTROL COMMON INJECTOR DRIVER NO. 1 FUEL INJECTOR NO. 1 HIGH-SIDE CONTROL

CAV 1 1 2 2 CIRCUIT 14BK/VT (EXCEPT OBD) 16BK/BL (OBD) 14BL (EXCEPT OBD) 16BK (OBD) FUNCTION FUEL INJECTOR NO. 2 CONTROL FUEL INJECTOR NO. 2 LOW-SIDE CONTROL COMMON INJECTOR DRIVER NO. 2 FUEL INJECTOR NO. 2 HIGH-SIDE CONTROL

CAV 1 1 2 2 CIRCUIT 14BK/RD (EXCEPT OBD) 16BK/DG (OBD) 14BK (EXCEPT OBD) 16DG (OBD) FUNCTION FUEL INJECTOR NO. 3 CONTROL FUEL INJECTOR NO. 3 LOW-SIDE CONTROL COMMON INJECTOR DRIVER NO. 1 FUEL INJECTOR NO. 3 HIGH-SIDE CONTROL
261
CONNECTOR PINOUTS

CAV 1 1 2 2 CIRCUIT 14BK/YL (EXCEPT OBD) 16BK/VT (OBD) 14BK (EXCEPT OBD) 16BL/WT (OBD) FUNCTION FUEL INJECTOR NO. 4 CONTROL FUEL INJECTOR NO. 4 LOW-SIDE CONTROL COMMON INJECTOR DRIVER NO. 1 FUEL INJECTOR NO. 4 HIGH-SIDE CONTROL

CAV 1 1 2 2 CIRCUIT 14BK/DG (EXCEPT OBD) 16BK/YL (OBD) 14BL (EXCEPT OBD) 16BK/WT (OBD) FUNCTION FUEL INJECTOR NO. 5 CONTROL FUEL INJECTOR NO. 5 LOW-SIDE CONTROL COMMON INJECTOR DRIVER NO. 2 FUEL INJECTOR NO. 5 HIGH-SIDE CONTROL
FUEL PRESSURE SENSOR - BLACK

CAV 1 2 3 20BR/GY 20DG/VT 20RD/DG CIRCUIT FUNCTION FUEL PRESSURE SENSOR GROUND FUEL PRESSURE SENSOR SIGNAL FUEL PRESSURE SENSOR 5 VOLT SUPPLY
FUEL PRESSURE SOLENOID

CAV 1 2 20BK/WT 20RD/WT CIRCUIT FUNCTION FUEL PRESSURE SOLENOID CONTROL FUEL PRESSURE SOLENOID 12 VOLT SUPPLY
FUEL PUMP (OBD)

CAV 1 2 14BK 14BR CIRCUIT FUEL PUMP RELAY OUTPUT GROUND FUNCTION
262
CONNECTOR PINOUTS
FUEL PUMP RELAY (OBD)
CAV 30 85 86 87 87A 14RD/BK 18BR/RD 18BK/RD 14BK CIRCUIT FUSED B(+) FUEL PUMP RELAY CONTROL FUSED ENGINE CONTROL RELAY OUTPUT FUEL PUMP RELAY OUTPUT FUNCTION
FUEL QUANTITY CONTROL VALVE (OBD)

CAV 1 2 20BK/WT 18RD/BK CIRCUIT FUNCTION FUEL QUANTITY SOLENOID CONTROL FUEL QUANTITY SOLENOID 12 VOLT SUPPLY
FUEL TEMPERATURE SENSOR

CAV 1 2 18DG/BK 18BL/GY CIRCUIT FUNCTION FUEL TEMPERATURE SENSOR GROUND FUEL TEMPERATURE SENSOR SIGNAL
263
CONNECTOR PINOUTS
264
CONNECTOR PINOUTS
ENGINE CONTROL RELAY (FUSE BLOCK NO. 1)
CAV 30 85 86 87 87A CIRCUIT INTERNAL INTERNAL INTERNAL INTERNAL FUSED B(+) ENGINE CONTROL RELAY CONTROL FUSED B(+) ENGINE CONTROL RELAY OUTPUT FUNCTION
FUSES (FUSE BLOCK NO. 1)

FUSE NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 10A 10A 10A 10A 20A 15A 20A 15A 10A 10A 10A 10A 15A 10A 15A 15A 15A 15A 15A 30A AMPS 16WT 16WT 16WT/BL/RD 16BK/BL/WT INTERNAL 16BK/YL 16RD/YL INTERNAL 16GY/DG/RD 16GY/BK 18YL 18YL 16BK/YL/WT 16BK/RD 12BK/BL 16BK/RD 14BK 14RD/BK (OBD) 16RD/BL 12RD FUSED CIRCUIT FUNCTION FUSED HIGH BEAM SWITCH OUTPUT FUSED HIGH BEAM SWITCH OUTPUT FUSED IGNITION SWITCH OUTPUT (RUN-START) FUSED IGNITION SWITCH OUTPUT (RUN-START) FUSED IGNITION SWITCH OUTPUT (RUN-START) FUSED IGNITION SWITCH OUTPUT (RUN-START) FUSED B(+) FUSED B(+) HEADLAMP SWITCH OUTPUT FUSED LEFT LAMP RELAY OUTPUT HEADLAMP SWITCH OUTPUT HEADLAMP SWITCH OUTPUT FOG LAMP RELAY SIGNAL FUSED IGNITION SWITCH OUTPUT (ACC-RUN-START) ENGINE CONTROL RELAY OUTPUT ENGINE CONTROL RELAY OUTPUT FUSED IGNITION SWITCH OUTPUT (RUN-START) FUSED B(+) FUSED B(+) FUSED B(+)
265
CONNECTOR PINOUTS
266
CONNECTOR PINOUTS
FUSES (FUSE BLOCK NO. 2)
FUSE NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 10A 10A 15A 7.5A 25A 7.5A 25A 10A 15A 7.5A 7.5A 25A 15A 10A 25A AMPS 16RD/GY 16RD 16RD 16RD/YL 14RD/WT 18RD/YL 16BK/YL 16BK/RD 16RD/YL/WT 16RD/YL/WT 16RD/YL/WT 14RD 14RD 14RD 16BK/YL/DG FUSED CIRCUIT FUSED B(+) FUSED B(+) FUSED B(+) FUSED B(+) FUSED B(+) FUSED B(+) OPTIONAL EQUIPMENT RELAY OUTPUT OPTIONAL EQUIPMENT RELAY OUTPUT FUSED D+ RELAY NO. 1 OUTPUT FUSED D+ RELAY NO. 1 OUTPUT FUSED D+ RELAY NO. 1 OUTPUT FUSED B(+) FUSED B(+) FUSED B(+) OPTIONAL EQUIPMENT RELAY OUTPUT FUNCTION
267
CONNECTOR PINOUTS
268
CONNECTOR PINOUTS
FUSES (FUSE/RELAY BLOCK)
FUSE NO. 1 2 3 4 5 6 7 8 9 10 10A 7.5A 25A 40A 40A 30A 30A 16RD/YL 18BK/RD 14RD 12RD 12RD 12RD/GY AMPS 14BL/YL FUSED B(+) FUSED OPTIONAL EQUIPMENT RELAY OUTPUT FUSED B(+) FUSED B(+) FUSED B(+) FUSED B(+) FUSED CIRCUIT FUSED B(+) FUNCTION
STARTER MOTOR RELAY (FUSE/RELAY BLOCK)

CAV 30 85 86 86 87 87A 12BK/YL 18VT/DG 18RD/BL (EXCEPT OBD) 18BK/RD (OBD) 12VT CIRCUIT STARTER MOTOR RELAY OUTPUT STARTER MOTOR RELAY CONTROL STARTER MOTOR RELAY 12 VOLT SUPPLY STARTER MOTOR RELAY 12 VOLT SUPPLY IGNITION SWITCH OUTPUT (START) FUNCTION
269
CONNECTOR PINOUTS
GLOW PLUG CONTROL MODULE C1 - BLACK

CAV 1 2 3 18BR 18BK/RD CIRCUIT GROUND GLOW PLUG MODULE CONTROL FUNCTION
GLOW PLUG CONTROL MODULE C2 - BLACK

CAV 1 2 3 14BK/DG 14BK/YL 14BK/RD 14BK/VT 14BK/BL CIRCUIT FUNCTION GLOW PLUG NO. 5 SUPPLY VOLTAGE GLOW PLUG NO. 4 SUPPLY VOLTAGE GLOW PLUG NO. 3 SUPPLY VOLTAGE GLOW PLUG NO. 2 SUPPLY VOLTAGE GLOW PLUG NO. 1 SUPPLY VOLTAGE -
4 5 6
INTAKE AIR PRESSURE SENSOR (OBD)

CAV 1 2 3 20BR/RD 20VT/DG 20VT/RD CIRCUIT FUNCTION INTAKE PRESSURE SENSOR GROUND INTAKE PRESSURE SENSOR SIGNAL INTAKE PRESSURE SENSOR 5 VOLT SUPPLY
INTAKE AIR TEMPERATURE SENSOR - BLACK

CAV 1 2 18BR/DG 18DG/WT CIRCUIT FUNCTION INTAKE AIR TEMPERATURE SENSOR GROUND INTAKE AIR TEMPERATURE SENSOR SIGNAL
270
CONNECTOR PINOUTS
KICK DOWN SWITCH - BLACK

CAV 1 2 2 18BR/DG 18BR (EXCEPT OBD) 18BR (OBD) CIRCUIT SENSOR GROUND GROUND FUNCTION KICKDOWN SWITCH SIGNAL
MASS AIR FLOW SENSOR - BLACK

CAV 1 2 2 3 3 4 4 5 CIRCUIT 16YL/RD (OBD) 20YL/RD (EXCEPT OBD) 20BR/VT (OBD) 20BR/YL (EXCEPT OBD) 20YL/BL (OBD) 20BR/BK (EXCEPT OBD) 20YL/DG (OBD) 20YL/DG (EXCEPT OBD) FUNCTION FUSED IGNITION SWITCH OUTPUT (RUN-START) MASS AIR FLOW SENSOR 12 VOLT SUPPLY MASS AIR FLOW SENSOR 5 VOLT SUPPLY MASS AIR FLOW SENSOR GROUND MASS AIR FLOW SENSOR GROUND MASS AIR FLOW SENSOR 5 VOLT SUPPLY MASS AIR FLOW SENSOR SIGNAL MASS AIR FLOW SENSOR SIGNAL
OXYGEN SENSOR (OBD)

CAV 1 2 3 4 5 6 20DG/BK 20GY/WT 20GY/BL 20RD/DG 20DG/YL 20GY CIRCUIT O2 1/1 PUMP CELL SIGNAL O2 1/1 VIRTUAL GROUND O2 1/1 HEATER CONTROL FUSED ENGINE CONTROL RELAY OUTPUT O2 1/1 PUMP CELL CONTROL O2 1/1 SENSOR CELL SIGNAL FUNCTION
271
CONNECTOR PINOUTS
272
CONNECTOR PINOUTS
FUSED IGNITION SWITCH RUN-START RELAY (RELAY BLOCK)
CAV 30 85 86 87 87A 14RD 18BK 16BR 14BK/YL CIRCUIT FUSED B(+) FUSED IGNITION SWITCH OUTPUT (RUN-START) GROUND FUSED IGNITION SWITCH RUN-START RELAY OUTPUT FUNCTION
SPEED CONTROL SWITCH

CAV 1 2 3 4 5 6 18GY 18BK 18BL 18YL 18DG 18RD CIRCUIT OFF SIGNAL VERIFICATION SIGNAL RESUME SIGNAL DECEL/SET SIGNAL ACCEL/SET SIGNAL S/C SWITCH 12 VOLT SUPPLY FUNCTION
WATER IN FUEL SENSOR - BLACK

CAV 1 2 3 18BR 18BR/RD 18BK/YL CIRCUIT FUNCTION WATER IN FUEL SENSOR GROUND WATER IN FUEL SENSOR 12 VOLT SUPPLY WATER IN FUEL SENSOR SIGNAL
273
NOTES
274
SCHEMATIC DIAGRAMS
10.0 10.1 SCHEMATIC DIAGRAMS ENGINE CONTROL MODULE
S C H E M A T I C D I A G R A M S
275
SCHEMATIC DIAGRAMS
10.2 ENGINE CONTROL MODULE
S C H E M A T I C D I A G R A M S
276
CHARTS AND GRAPHS

11.0 CHARTS AND GRAPHS
C H A R T S A N D G R A P H S
277
NOTES
278
DIAGNOSTIC TEST PROCEDURES TELL US!

DaimlerChrysler Corporation is constantly working to provide the technician the best diagnostic manuals possible. Your comments and recommendations regarding the diagnostic manuals and procedures are appreciated.
To best understand your suggestion, please complete the form giving us as much detail as possible.
Model Transmission Diagnostic Procedure
Year
Body Type Vehicle Mileage Book No.
Engine MDH Page
Comments/recommendations (if necessary, draw sketch)
Name
Submitted by: Address City/State/Zip Business Phone #

All comments become property of DaimlerChrysler Corporation and may be used without compensation.
Dealer Technical Operations 800 Chrysler Drive CIMS 486-02-76 Auburn Hills, MI 48326-2757

2006 VA Powertrain Sprinter

Uploaded by

Copyright:

Available Formats

2006 VA Powertrain Sprinter

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

2006 VA Powertrain Sprinter

Uploaded by

Copyright:

Available Formats

What is the purpose of the document?

What is the purpose of the document?

What topics are covered in the document?

What topics are covered in the document?

TABLE OF CONTENTS

5.0 6.0 7.0

TABLE OF CONTENTS - Continued

TABLE OF CONTENTS - Continued

TABLE OF CONTENTS - Continued

TABLE OF CONTENTS - Continued

TABLE OF CONTENTS - Continued

TABLE OF CONTENTS - Continued

TABLE OF CONTENTS - Continued

TABLE OF CONTENTS - Continued

TABLE OF CONTENTS - Continued

TABLE OF CONTENTS - Continued

SYSTEM DESCRIPTION AND FUNCTIONAL OPERATION GENERAL DESCRIPTION

FUNCTIONAL OPERATION ECM ON-BOARD DIAGNOSTICS

SIX-STEP TROUBLESHOOTING PROCEDURE

verification of proper operation

Overspeed Detection Mode

Ignition Switch On (Engine Off)

Engine Start-Up Mode

Normal Driving Modes

Overheat Production Mode

SKREEM ON-BOARD DIAGNOSTICS

DIAGNOSTIC TROUBLE CODES

ECM DIAGNOSTIC TROUBLE CODES

USING THE DRBIII

SAFETY TECHNICIAN SAFETY INFORMATION

DRBIII DOES NOT POWER UP

DISPLAY IS NOT VISIBLE

VEHICLE PREPARATION FOR TESTING

DRBIII SAFETY INFORMATION

WARNINGS AND CAUTIONS ROAD TEST WARNINGS

VEHICLE DAMAGE CAUTIONS

REQUIRED TOOLS AND EQUIPMENT

DRBIII (diagnostic read-out box) scan tool vacuum gauge ammeter

7.0 DIAGNOSTIC INFORMATION AND PROCEDURES

The ECM internal Atmospheric Pressure Sensor is faulty.

The ECM internal Atmospheric Pressure Sensor is faulty.

POSSIBLE CAUSES ENGINE CONTROL MODULE INTERMITTENT CONDITION

The ECM detects a rationality problem with the MAF Sensor.

Intake Pressure Sensor Signal voltage is 4.9 volts or greater.

Intake Pressure Sensor Signal voltage is 0.2 volt or lower.

The fuel temperature sensor signal voltage is above 4.7 volts.

The fuel temperature sensor signal voltage is below 0.8 volt.

When Monitored and Set Condition:

The ECM detects an open or short to ground on the Cylinder #1 Injector

The ECM detects a short to ground on the Cylinder #1 Injector circuit.

The ECM detects a short to voltage on the Cylinder #1 Injector circuit.

The ECM detects an open or short to ground on the Cylinder #2 Injector

The ECM detects a short to ground on the Cylinder #2 Injector circuit.

The ECM detects a short to voltage on the Cylinder #2 Injector circuit.

The ECM detects an open or short to ground on the Cylinder #3 Injector

The ECM detects a short to ground on the Cylinder #3 Injector circuit.

The ECM detects a short to voltage on the Cylinder #3 Injector circuit.

The ECM detects an open or short to ground on the Cylinder #4 Injector

The ECM detects a short to ground on the Cylinder #4 Injector circuit.

The ECM detects a short to voltage on the Cylinder #4 Injector circuit.