BUTTERFLY VALVE
SERIES NE STYLE
INFORMATION
The MUD KING wafer and lug type butterfly valves are designed to meet the stringent requirements of
chemical plants, processing plants, power plants, refineries, shipbuilding, pulp and paper mills, and wherever
positive shut-off is required for liquids, oil, gas, and gas slurries. They are also the ideal choice for heating,
ventilation and air conditioning applications.
THE LEADER AND #1 CHOICES IN THE OIL DRILLING INDUSTRY
STEM FLATS INDICATOR
POSITION OF DISC
TWO SELF-LUBRICATING
BRONZE BEARINGS
PROVIDE LOAD SUPPORT
AND SMOOTH OPERATING
STEM RETAINER PINS
ENSURING A BLOW
DOUBLE DRIVE
OUT PROOF DESIGN
GIVES POSITIVE
STEM AND DISC
CONNECTION
MAXIMUM FLOW DISC
PROVEN PHENOLIC
BONDED CARTRIDGE
SEAT ONE PIECE
RIBBED WAFER
OR LUG BODY
NE BUTTERFLY VALVES 2" – 12"
14" – 24" AVAILABLE ON REQUEST
Demco is a registered trademark of another company. MUD KING Products is not affiliated with Demco. Reference to company
name is for identification purposes only and are not trademarks or trade names used by or affiliated with MUD KING Products. Page 1
BUTTERFLY VALVE
DESIGN FEATURES - 2" – 12"
FLANGE SEALS
The inner surface of the seat is widened to project outside the
face-to-face width of the valve body. When mounted between
weld neck or socket flanges, the extra rubber is compressed to
form a positive seal against both flanges. The seal surface, near
the outer periphery of each seat face is designed to seal against
slip-on or threaded flanges. Only valves with throttling discs
require gaskets.
DISC DRIVE
Proper – orientation of the stem/disc connection is assured by
the rectangular drive. The disc is permitted to float on the stem
to perfectly center in the valve seat.
BODY
One piece bodies are ribbed to assure high strength and
minimum weight. Bodies are cast in both wafer and tapped-lug STEMS
patterns, in a wide variety of material choices, to meet virtually Upper stems are flatted for positive drive and for easy installation
every installation requirement. of handles and actuators.
Body rating is ANSI Class 150 (285 psi non-shock). Wafer Retained by tangential pins, upper and lower stems are
body diameters are designed to self-center in ANSI 150 flange blowout proof for safety when handles or actuators are removed
patterns. from the valve top.
The large top flange provides a secure mounting area for
automatic or manual actuators. STEM JOURNAL
Two self-lubricating bronze bearings reduce torsional friction,
eliminate galling and seizing of the stem, while supporting the
DISC stem against side loading from pressure on the closed disc.
MK Butterfly Valve discs and seat are configured for MK places one bearing at the base of the stem.
low pressure drop and high flow coefficients. Full radius
polished edges slide into drop tight seat engagement with little
turning effort. STEM SEALS
The stem holes in the disc are surrounded by an annular raised
Disc
land which passes the seat onto the seat flat at every angular
position of the disc. The resilient seat presses back with a
higher specific force than the line pressure, preventing leakage
to the stem.
In competitive stem seal designs with boot seats, a seal is
accomplished by an interference “squeezing" on the stem,
or an o-ring in the stem journal. The potential for leakage
SEAT Stem
behind the seat is high. As the disc wipes the seat, elongation
The MK Butterfly Valve seat is constructed by bonding a of the stem seal area allows leakage to collect behind the seat.
resilient elastomer to a rigid back-up ring, which forms the This condition is eliminate by MKP dry stem journal and
outside periphery of the seat. Slip fitted in the valve body, the hard-backed seat.
seat is field replaceable without special tools. In the closed
position, the disc rim and stem seal lands form an uninterrupted
line of sealing contact with the resilient seat, to assure
drop tight sealing at rated shutoff pressure. MKP seats is
offered in a wide range of materials.
Page 2
BUTTERFLY VALVE
DESIGN FEATURES – 2" × 12"
PRESSURE RATING ACTUATION
Three drop tight pressure ratings are offered for Positive latch handles, worm gear operators,
MK Butterfly Valves. Normally, 200 psi shutoff is and automatic actuators are available and totally
used in butterfly applications. However, 285 psi inter-changeable on the MKP valve.
shutoff is optionally available for higher pressure
The MKP to flange is dimensionally compat-
applications. For smaller actuator sizing, 50 psi
ible with other competitive butterfly valves.
valves offer reduced torque.
With optional “utility top" stem, the MKP valve
For minimum torque, throttling valves, which do not interchange directly with competitive valves,
provide drop tight closure, are available. allowing valve replacement without the need for new
actuation.
END-OF-LINE SERVICE
Lug body valves may be used in end-of-line ser-
vice, with downstream piping removed. (Weld neck
or socket flanges, only can be used for this service).
Since upstream pressure is excluded between the
flange seal, there is no effective force to slide the seat
downstream.
MKP Lug Butterfly Valves are recommended for
liquid service up to 200 psi with downstream piping
removed.
Lug body valves are recommended for isolation of
pumps, control devices, or other system compo- INSTALLATION AND MAINTENANCE
nents which may need to be removed for repair or
MKP Butterfly Valves are bi-directional, with
replacement. Lug valves are also suitable for
identical flow-way from either face. To install,
installation at points from which piping expansions
simply close the valve, insert between flanges
may proceed. Such valves are normally blanked with
and make up with studs or cap screws. No regular
blind flanges, to protect the exposed seats, until new
maintenance or lubrication is ever required.
piping is attached.
Disassembly is simple, for inspection or
replacement of parts. Open the valve, remove handle
or actuator, remove tangential pins, pull out stems
and push the disc and seat out of the body. Reassem-
ble in reverse order, with a small amount of general
purpose non-hydrocarbon based lubricant on the out-
side of stems, seat, and disc flats.
Steel or cast iron flanges of either raised or
flat-faced type are suitable for use with
MKP Butterfly Valves.
Page 3
BUTTERFLY VALVE
ORDERING INFORMATION FOR NE STYLE
VALVE ASSEMBLY PART NUMBER
A base part number defines series, size, and shutoff pressure, and is followed by a
7-digit suffix which specifies all options, including handles.
BODY CONFIGURATION 1 Wafer 5 Lug
BODY MATERIAL 4 Ductile Iron ( Lug) 2 Gray Iron (Wafer 2" – 12"; Lug 2" – 8")
1 416 SS
STEM MATERIAL
2 316 SS 4 Aluminum Bronze
DISC MATERIAL 5 Nickle Plated Ductile Iron 6 Nylon 11 Coated Ductile Iron
31 Buna-N 32 Black Neoprene 33 Hypalon 34 Viton 35 EPDM
BASE SEAT ELAS. 36 Natural Rubber 37 White Neoprene × Special
NUMBER HANDLE 1 10 Position Lug 5 Square Nut 6 2 Position Lkg. 9 None
(from table
below)
XXXXX - X X X X X X
COMPONENT DESCRIPTION 2" 2½" 3" 4" 5" 6" 8" 10" 12"
NE-C 200 psi M22119 M22120 M22121 M22122 M22123 M22124 M22125 M22126 M22127
WEIGHT Wafer 5.8 7.0 7.7 11.4 14.7 17.6 28.5 47.9 71.0
LBS. Lug 8.0 9.9 10.7 17.0 24.5 28.5 43.5 65.9 98.5
NE-D 200 psi M22181 M22129 M22182 M22183 M22184 M22185 M22134 M22186 M22136
Weight (lbs. - bare stem) Wafer 4.9 6.4 6.9 10.2 13.7 16.4 28.4 44.8 66.8
HANDLE PARTS - STANDARD TRIM
REF
COMPONENT DESCRIPTION 2" – 4" 5" – 6" 8" 10" 12"
NO.
ASSY. BASE PART NO. -10 POSITION M24227-001 M24228-001 M24229-001 M24230-001 M24231-001
-2 POSITION M24232-001 M24233-001 M24234-001 M24235-001 M24236-001
1 SCREW Steel M5650-24020 M5650-28024
2 HANDLE Ductile Iron M24237-001 M24238-001 M24239-001 M24240-001 M24241-001
3 LATCH Zinc Plated Steel M23719-001 M23720-001 M23721-001
4 SPRING Spring Steel M16238
5 SPRING PIN Spring Steel M5445-25014 M5446-37516
6 THROTTLE PLATE -10 POSITION M24242-001 M24243-001 M24244-001 M24245-001 M24246-001
-2 POSITION M24247-001 M24248-001 M24249-001 M24250-001 M24251-001
7 LOCK WASHER Steel M5900-006 M5901-008
8 NUT Zinc Plated Steel M5327-024 M5327-028
9 SET SCREW Steel M5727-22012 M5727-22016
DIMENSIONS M 9.50 11.00 15.00 15.00 22.00
N 0.85 1.07 1.13 1.13 1.13
HANDLE WEIGHTS (lbs) 2 or 10 Pos. Lkg. 2 3 5 5 9
Page 4
BUTTERFLY VALVE
REPLACEMENT PARTS FOR THE NE STYLE
REF
COMPONENT DESCRIPTION 2" 2½" 3" 4" 5" 6" 8" 10" 12"
NO.
1 BODY NE-C Wafer M22137-012 M22138-012 M22139-012 M22140-012 M22141-012 M22142-012 M22143-012 M22144-012 M22145-012
ASTM A48 Gray Iron -012
NE-C Lug M21986-05x M21987-05x M21988-05x M21989-05x M21990-05x M21991-05x M21992-05x M21993-051 M21994-051
Options ASTM A395 Ductile Iron -051, ASTM A48 Gray Iron -052
NE-D Wafer M22187-021 M22682-011 M22188-021 M22189-021 M22190-021 M22191-021 M22687-011 M22192-021 M22689-011
2 SEAT M1786-xxx M1788-xxx M1790-xxx M1792-xxx M1794-xxx M1002-xxx M1798-xxx M1815-xxx M1817-xxx
Options -031 Buna-N -032 Blk. Neoprene -033 Hypalon -034 Viton
-035 EPT -036 Nat. Rubber -037 While Neoprene -x Special
3 DISC 200 psi M22045-0xx M22046-0xx M22047-0xx M22048-0xx M22049-0xx M22050-0xx M22051-0xx M22052-0xx M22053-0xx
Options -002 316 SS -005 Ni. Plated Duct Iron -014 Alum. Bronze
4 UPPER STEM NE-C M22066-00x M22067-00x M22068-00x M22069-00x M22070-00x M22071-00x M22072 -00x
NE-D M22073-00x M22074-00x M22193-00x M22194-00x M22195-00x M22077-00x M22078-00x M22079-00x
6 LOWER STEM M22080-66x M22081-00x M22082-00x M22083-00x M22084-00x M22085-00x M22086-00x
Options -001 416 SS -002 316 SS -004 Phos. Coated Steel
7 SPRING PIN (2) 302 SS M5448-18720 M5448-18724 M5448-25028
8 RETAINER Stainless Steel M22117 M13704 M13705 M13706 M13707
9 TOP O-RING Buna-N M5526-114 M5526-115 M5526-117 M5526-119 M5526-125
10 STEM O-RING Buna-N M5526-113 M5526-115 M5526-116 M5526-212 M5526-214 M5526-220
11 BEARING Bronze M22526-001 M22118-001 M13112-001 M13115-001 M13116-001 M13117-001
Page 5
BUTTERFLY VALVE
SERIES NE-C STYLE 2"– 12"
ENGINEERING
THE NE-C STYLE BUTTERFLY
VALVES ARE OFFERED IN
WAFER OR LUG DESIGN
WHICH MOUNT IN BETWEEN
ANSI 125/150 FLANGES
DIMENSIONS
VALVE SIZE A C D E F G H J K L N P R S
2" 1.74 5.62 8.44 4.12 4.00 3.25 .408 4.75 5/8 - 11 4 1.00 .44 .625 .375
2½ " 1.86 6.12 9.19 4.88 4.00 3.25 .408 5.50 5/8 - 11 4 1.00 .44 .625 .375
3" 1.86 6.38 9.69 5.36 4.00 3.25 .408 6.00 5/8 - 11 4 1.00 .44 .625 .375
4" 2.11 7.12 11.00 6.88 4.00 3.25 .408 7.50 5/8 - 11 8 1.00 .44 .625 .375
5" 2.24 7.75 12.12 7.75 4.00 3.25 .408 8.50 3/4 - 10 8 1.25 .44 .838 .500
6" 2.24 8.25 13.25 8.75 4.00 3.25 .408 9.50 314 - 10 8 1.25 .44 .838 .500
8" 2.54 9.44 15.56 11.00 6.00 5.00 .533 11.75 3/4 - 10 8 1.38 .56 .838 .500
10" 2.74 11.25 18.69 13.38 6.00 5.00 .533 14.25 7/8 - 9 12 1.38 .56 .963 .625
12" 3.24 12.19 21.69 16.12 6.00 5.00 533 17.00 7/8 - 9 12 1.38 .56 1.338 .750
CLASS II
TORQUES (Inch - Pounds)
Shutoff Pressure 2" 2½" 3" 4" 5" 6" 8" 10" 12" Value 10° 20° 30° 40° 50° 60° 70° 80° 90°
Size
50 PSI SHUTOFF 88 96 150 225 350 450 750 1325 2250 2" 2 5 10 18 28 55 77 127 153
75 PSI SHUTOFF 98 141 237 243 504 651 1050 1778 2990 2½ ‘’ 3 7 14 24 41 87 115 186 242
100 PSI SHUTOFF 103 148 249 261 531 685 1105 1872 3147 3" 4 12 23 37 66 129 186 274 337
125 PSI SHUTOFF 107 155 260 375 553 714 1151 1950 3279 4" 6 24 44 76 125 241 312 521 601
150 PSI SHUTOFF 110 158 265 384 564 728 1775 1989 3345 5" 8 32 87 158 257 298 632 983 1122
175 PSI SHUTOFF 121 175 283 417 632 814 1337 2320 3928 6" 9 52 148 244 413 786 1028 1633 1949
200 PSI SHUTOFF 132 192 300 450 700 900 1500 2650 4500 8" 12 101 246 418 693 1279 1732 2702 3232
250 PSI SHUTOFF 145 211 318 485 770 990 1695 2995 5085 10" 21 165 393 667 1144 2140 2744 4276 4979
285 PSI SHUTOFF 160 232 337 528 847 1089 1915 3384 5746 12" 28 233 555 992 1588 3096 4044 6048 7481
Class II Notes:
> Valve to be operated a minimum of once a month. 1. The chart to be used as a guide only.
> Temperature wall within resilient seat limits. 2. These torque rating do not apply to every possible service criteria, which may affect seating and unseating torque.
> Line media is a self lubricating (Aqueous liquids) *. 3. Torque values are applicable to MUD KING NE-C values.
> Minor chemical attacks on seat. 4. Do not apply a safety factor to the above torque values when sizing actuators.
5. Dynamic Torque should always be a consideration when sizing valves with high differential pressures.
> Disc corrosion and media deposits to be mild. 6. For 3 way tee assemblies multiply the above torques by 1.5.
TYPE COMPOUND TYPE OF SERVICE TEMPERATURES
Buna-N General purpose elastomer compound for maximum hydrocarbon or petroleum. 0° F – 180° F
Black Neoprene Complies with FDA guidelines and generally used in food and beverage service and resistant to brine, vegetable oils, and oxygen. 0° F – 180° F
Same chemical resistant as black neoprene in physical properties are not as good as black. White neoprene should only be used when
White Neoprene 0° F – 180° F
black cannot be tolerated and storage should be in low light conditions.
Viton Excellent in harsh chemical environments and elevated temperatures. +20° F – 300° F
Hypalon Excellent in acids and hydrocarbons and very high chemical resistant. 0° F – 180° F
Natural Rubber Recommended for dry material handling and high abrasion resistance. Use in oils and solvents not recommended. +30° F – 150° F
EPDM Formulated to comply with FDA guidelines, this material in suitable for food service except edible oils and milk. +30° F – 275° F
MUD KING Products is not affiliated with EJ Dupont De Nemours. Reference to company name is for identification
Page 6 purposes only and are not trademarks or trade names used by or affiliated with MUD KING Products.
