Scribd
Upload
23 views7 pages

Network Address Translation (NAT) Static NAT: Router 1

Uploaded by

sivabalanapple13
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
23 views7 pages

Network Address Translation (NAT) Static NAT: Router 1

Uploaded by

sivabalanapple13
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 7

Network address translation(NAT)

Static NAT

Assign all IP address and gate way to all PC and Server

Turn on http SERVER

Assign router 1 and router 2 IP address only

Router 1

Would you like to enter the initial configuration dialog? [yes/no]: n

Press RETURN to get started!

Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface gigabitEthernet 0/0
Router(config-if)#ip address 10.0.0.1 255.0.0.0
Router(config-if)#no shutdown

Router(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state


to up

Router(config-if)#exit
Router(config)#interface gigabitEthernet 0/1
Router(config-if)#ip address 30.0.0.1 255.0.0.0
Router(config-if)#no shutdown

Router(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state


to up

Router(config-if)#exit
Router(config)#

Router 2

Would you like to enter the initial configuration dialog? [yes/no]: n

Press RETURN to get started!

Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface gigabitEthernet 0/0
Router(config-if)#ip address 20.0.0.1 255.0.0.0
Router(config-if)#no shutdown

Router(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state


to up
Router(config-if)#exit
Router(config)#interface gigabitEthernet 0/1
Router(config-if)#ip address 30.0.0.2 255.0.0.0
Router(config-if)#no shutdown

Router(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to up
Router(config-if)#exit
Router(config)#interface gigabitEthernet 0/1
Router(config-if)#ip route 0.0.0.0 0.0.0.0 30.0.0.1
Router(config)#exit
Router#
%SYS-5-CONFIG_I: Configured from console by console

Router#wr
Building configuration...
[OK]
Router#

Static NAT router 1


Router(config)#ip nat inside source static 10.0.0.5 50.0.0.5
Router(config)#ip nat inside source static 10.0.0.6 50.0.0.6
Router(config)#interface gigabitEthernet 0/0
Router(config-if)#ip nat inside
Router(config-if)#exit
Router(config)#interface gigabitEthernet 0/1
Router(config-if)#ip nat outside
Router(config-if)#exit
Router(config)#interface gigabitEthernet 0/1
Router(config-if)#ip route 0.0.0.0 0.0.0.0 30.0.0.2
Router(config)#exit
Router#
%SYS-5-CONFIG_I: Configured from console by console

Router#wr
Building configuration...
[OK]
Router#
Dynamic NAT

Router 1

Would you like to enter the initial configuration dialog? [yes/no]: n

Press RETURN to get started!

Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface gigabitEthernet 0/0
Router(config-if)#ip address 10.0.0.1 255.0.0.0
Router(config-if)#no shutdown

Router(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state


to up

Router(config-if)#exit
Router(config)#interface gigabitEthernet 0/1
Router(config-if)#ip address 20.0.0.1 255.0.0.0
Router(config-if)#no shutdown

Router(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to up
Router(config-if)#exit
Router(config)#
Router 2
Would you like to enter the initial configuration dialog? [yes/no]: n

Press RETURN to get started!

Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface gigabitEthernet 0/0
Router(config-if)#ip address 20.0.0.2 255.0.0.0
Router(config-if)#no shutdown

Router(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state


to up

Router(config-if)#exit
Router(config)#interface gigabitEthernet 0/1
Router(config-if)#ip address 30.0.0.1 255.0.0.0
Router(config-if)#no shutdown

Router(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to up

Router(config-if)#exit
Router(config)#interface gigabitEthernet 0/0
Router(config-if)#ip route 0.0.0.0 0.0.0.0 20.0.0.1
Router(config)#interface gigabitEthernet 0/1
Router(config-if)#ip route 0.0.0.0 0.0.0.0 30.0.0.2
Router(config)#^Z
Router#
%SYS-5-CONFIG_I: Configured from console by console

Router#wr
Building configuration...
[OK]
Router#
Router 3

Would you like to enter the initial configuration dialog? [yes/no]: n

Press RETURN to get started!

Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface gigabitEthernet 0/0
Router(config-if)#ip address 40.0.0.1 255.0.0.0
Router(config-if)#no shutdown

Router(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state


to up

Router(config-if)#exit
Router(config)#interface gigabitEthernet 0/1
Router(config-if)#ip address 30.0.0.2 255.0.0.0
Router(config-if)#no shutdown

Router(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state


to up

Router(config-if)#exit
Router(config)#interface gigabitEthernet 0/1
Router(config-if)#ip route 0.0.0.0 0.0.0.0 30.0.0.1
Router(config)#^Z
Router#
%SYS-5-CONFIG_I: Configured from console by console

Router#wr
Building configuration...
[OK]
Dynamic NAT
Router 1
Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#access-list 33 permit 10.0.0.0 0.255.255.255
Router(config)#ip nat pool tsrss 50.0.0.5 50.0.0.20 netmask 255.0.0.0
Router(config)#ip nat inside source list 33 pool tsrss overload
Router(config)#interface gigabitEthernet 0/0
Router(config-if)#ip nat inside
Router(config-if)#exit
Router(config)#interface gigabitEthernet 0/1
Router(config-if)#ip nat outside
Router(config-if)#exit
Router(config)#interface gigabitEthernet 0/1
Router(config-if)#ip route 0.0.0.0 0.0.0.0 20.0.0.2
Router(config)#
Router(config)#^Z
Router#
%SYS-5-CONFIG_I: Configured from console by console

Router#wr
Building configuration...
[OK]
Router#

You might also like