DMR21 TECHNICAL MANUAL 2E

AS
Y

Apartment Intercom System

2-wire series

CONTENTS

Installation Guide..........................................................................2

Modules. .......................................................................................4

Camera Module.........................................................................4

Keypad Module..........................................................................6 RF CARD

TFT Module. ...............................................................................11

Card Reader Module..................................................................12

Call Button Module ....................................................................14 DMR21/S8 DMR21/D16 DMR21/S4/F1 DMR21/D8/F1

Module Connection. ......................................................................16

CONFIGURATIONS......................................................................19

Common Door Station Setting ....................................................19

1 2 3 4 1 2 3 4
5 6 7 8 5 6 7 8

Software Update .........................................................................20

RF CARD

9 0 * # 9 0 * #

A B A B

Tone Update ...............................................................................20

RF CARD RF CARD

Namelist Update .........................................................................21

DMR21/F2 DMR21/D32/F1 EP21/F3 EP21/S12
 INSTALLATION GUIDE
Y
AS
2E

DESCRIPTION TERMINALS

New generation Direct Call Apartments door stations are modular

POW
GND

GND
GND
CTR
DAT
STR
CLK
12V

VIO
design with a flexibility to combine modules.

C2
C1
ON DIP

SET
For example,the video entry module can be assembled with card JP-LK CN/KMB CN/T-COIL
1 2 3 4 5 6
reader module and/or with keypad module.

WG1
WG0
GND
12V
GND

GND

GND
RST
5DA

RX3

RX1
5CL

TX3

TX1
12V
INT
CN-LK
Additional combinations are available: TFT Screen Module with L1 L2
CN/FUN CN/WGN

EB+
EB-
NO
LK+
LK-
+12V
Proximity Reader Module or Keypade Module. Calling to apartments
will be performed by Name List visible on the screen

• +12V: 12VDC power output

• LK-: Power ground
• LK+: Common contact of the relay
• NO.: Normally open contact of the relay
• EB+: Exit button positive connection port
• EB-: Exit button negative connection port
• JP-LK: Electic lock type setting
PARTS AND FUNCTIONS
• SET : DIP switches for door station settings
• CN/KMB: Call button module connection port
• CN/T-COIL: Reserved
Speaker
Camera Lens
• CN/FUN: Touch sensor keypad module or TFT display module
Night View LED connection port
Microphone • CN/WGN: Proximity reader module connection port
ON DIP

A B
1 2 3 4 5 6

Connection port
L1 L2

Status Indicator
ID Card Window • Bus(L1,L2): Non-polarity bus line, connect to power supply
316 mm

RF CARD

Nameplate
Call button

Screw hole

133 mm

PLACE NAMEPLATE

Press down and move right/left to open the transparent nameplate

cover. Then insert the name paper and put the cover back. Note that
the double row button panel can be opened both direction, single row
button can only be opened at right side

Calo
vid
Da

Embedded box Stainless steel panel

name paper

-2- DMR21 Technical Manual

 INSTALLATION GUIDE
Y
AS
2E

MOUNTING SYSTEM CONNECTION

Standard mounting

1 2 Code=32 Code=31 Impedance OFF ON

switch

A B C D

DBC4A
Code=30 Code=29

Cut a hole and install the wall box Connect and plug bus line connector with cable
Code=8 Code=7
3 4 Impedance
switch
OFF ON

A B C D

DBC4A
Code=6 Code=5

Code=4 Code=3
Impedance OFF ON

Use screws to fasten the panel Final result switch

A B C D

DBC4A
Code=2 Code=1

Mounting with expanding panel

AC~
100~240VAC
1 2

PC6

BUS(IM) BUS(DS)

Cut a hole and install the wall box Connect and plug bus line connector with cable

3 4 RF CARD

Use the screws to fasten the panel Final result

DMR21 Technical Manual -3-

 INSTALLATION GUIDE
Y
AS
2E

2) Door Lock Controlled with External Power

DIP SWITCHES SETTING
1. The external power supply must be used according to the lock
Totally 6 bits can be configured by dip-switch. The switches can be
modified either before or after installation, but restarting the power is 2. The jumper must be taken off before connecting
needed whenever the switches have been modified 3. Setup the Unlock Mode Parameter for different lock types
ON(1) OFF(0) • Power-on-to-Unlock type:Unlock Mode=0(default)
ON
ON ON • Power-off-to-Unlock type:Unlock Mode=1
= =
1 2 3 4 5 6
4. If different unlocking time is needed to be configured, change the
unlock time on door station,more detail information refer to DT system
Bit-1 and Bit 2 is for door station ID settings. When multi door stations technical guide
are installed in the system, these two bit must be set correctly, the
first door station set to 00, the second one set to 01, the third one set
to 10, the fourth one set to 11. If only one door station is installed, set Power-on-to-Unlock type: Power-off-to-Unlock type:
to 00.

Bit-3 is for single or double row button door station selection. If the Cut off the line Cut off the line
- -
door station is a double row button, such as DMR21-D8, set this bit to +
+12V
+
+12V
+ LK - (GND)
0. For single row button door station,set to 1.
LK - (GND)
LK+(COM) + LK+(COM)
N.O.
- N.O.
EB- - EB-
EB+
Exit button EB+
Bit-4 is for button code selection. if use the default codes for each 1 2 3
Exit button
Take off the Jumper 1 2 3

button of the door station, set to 0. If use the programmed codes, set JP_LK Take off the Jumper
JP_LK
to 1.(the code for each button can be programmed by software, detail
information refer to DT system technical guide)

Bit-5 is for unlocking time quick setting. 0 is the default setting,and the
default time is 1 second. If set to 1,the unlock time is 5 seconds(the
unlock time can be modified by door station or software) SPECIFICATIONS
Bit-6 is for activating the key A and key B. Normally key A and key B
is not activated(about the functions of key A and key B,please refer to
DT system technical guide ),Just when it set to 1,the key A and key B
is activated.

ELECTRIC LOCK CONNECTION

1) Door Lock Controlled with Internal Power

1. The door lock is limited to 12Vdc, and holding current must be less
than 250mA when using internal power supply mode

2. The Unlock Mode Parameter must be set to 0 (default).

3. Jumper set to 1-2 position for power-off-to-unlock safety

type(Normally closed mode); set to 2-3 position for power-on-to
-unlock type(Normally open mode ).

4. If different unlocking time is needed to be configured, change the

unlock time on door station,detailed information refer to DT system
technical guide

Power-on-to-Unlock type: Power-off-to-Unlock type:

12V 300mA
+12V
- - +12V
LK -
LK+ LK -
+ LK+
N.O.
12V 300mA EB- + N.O.
EB+ EB-
Exit button EB+
1 2 3 Exit button
Jumper position in 2-3 1 2 3
JP_LK Jumper position in 1-2
JP_LK

-4- DMR21 Technical Manual

 MODULES
Y
AS
2E

CAMERA MODULE • Warning Tune Setting

When the door station with Camera Module in standby:

1. Parts and functions
(1)Press and holld Key A for 3 seconds to enter the Warning Tune
Speaker Option Mode, the Status indicator turns on and the current tune
will be played
Camera lens
(2)Press Key A again to play next tune
Night view LED
(3)Press Key B to exit
MIC

Invisible key B
Invisible key A
Status indicator
Talk indicator
• Tune Volume Setting
Unlock indicator
When the door station with Camera Module is standby:

(1)Press Key B to enter Tune Volume Setting, the Talk indicator

Note: Key A and key B can not be seen on the panel,they are cryptic. turns on and plays the tune at current volume
Normally, key A and key B are not active. To activate the buttons,
just set the DIP6 to ON position (2)Press Key A to increase/decrease volume

(3)Press B to exit
2. Settings via touch button If TFT Module is connected, the current Volume will be displayed on
screen
Please know that the DIP6 switch must be set to ON while the others
are set to OFF to carry on the following settings.

• Unlocking Mode Setting

When the door station with Camera Module in standby:

(1)Press Key A, the Unlock indicator turns on with the warning sound
of BP+, BP;
• Talk Volume Setting
(2)Press Key A again to set the Unlocking Mode to Normally Open (1)During conversation, press and hold Key B for 3 seconds to
or Normally Closed. (Normally Open: the Status indicator blinks enter the Talk Volume Setting. The Talk indicator turns on with the
ones with the warning sound of BP+; Normally Closed:the Status warning sound of BP+,BP
indicator blinks twice with the warning sound of BP+, BP)
(2)Press Key A to increase/decrease volume
If TFT Module is connected, the info will be displayed on screen
(3)Press Key B to exit

• Unlocking Time Delay Setting

When the door station with Camera Module in standby:

3. Restore to factory setting
(1)Press Key A, the Unlock indicator turns on with the warning sound
of BP+, BP;
Attention: All settings will be canceled if the Restore Factory Setting
(2)Press and hold Key B to enter the Unlocking Time Delay Setting, a is activated. Include the modules setting, such as Proximity module,
warning sound of BP will be heard and the Status indicator blinks Keypad module (even if the modules are not connected to the
one time per second Camera Module)

The counting of Unlocking Time is the times that Status indicator When in standby mode, short out the Exit Button Port(EB+,EB-),
blinks (the units is second). For example,the Status indicator blinks then continuously toggle the DIP-6 switch for 4 times with a warning
for four times,that means the unlocking time is 4 seconds sound of BP+, and the three Indicators will blink at the same time,
that means the Restore Factory Setting is in progress; If the three
Indicators turn off with a warning sound of BP+,it means the Restore
Factory Setting is finished

DMR21 Technical Manual -5-

 MODULES
Y
AS
2E

KEYPAD MODULE

1. Parts and functions

 • The example is set as cancel button and # as
confirm button,please refer to */# function setting
for detail information
• Forbid to slide to touch the digital keypad,it may
cause mistaken key,the correct operation is using
your finger to press the digit you desired
Mounting
screw • You should press“confirm”button after finish input-
ting the code number each time,otherwise,the
Touch sensor
operation will be cancelled automatically in 10s
keypad
Call button

Setting items Setting range Default Setting

value code

Reset all settings 1,2,3,4 - 00

2. Keypad operation with TFT module
1 ~ 12 digits
Setting the master code 1234 01
Valid keys:0 ~ 9
• Call Residents
Setting the key 10 to 99 seconds/
10 sec 02
Input room number directly, the screen will be showed the room illumination time continually lit
number, press to start calling
Setting the unlock time 01 to 99 seconds 1 sec 03

Setting the unlock mode 0:opened/1:closed opened 04

Operation tone settings 0,1,2 on 05

Reset code settings 1,2,3,4 - 06

&# function settings 0:Normal/1:Reverse Normal 07

Call tone settings 0:Enable/1:Disable Enable 08

Interference resistant
• Password Unlocking Valid keys:0 ~ 5 2 09
grade settings
Input password +”#” to unlock the door. SPK Adjustment Valid keys:0~9 5 11

Night light level Valid keys:0 ~ 5 4 13

Reserve Reserve Reserve 14~17

Setting the code 1 ~ 12 digits

- 18
forTemporary1 Valid keys:0~9

Setting the code 1 ~ 12 digits

- 19
forTemporary2 Valid keys:0~9

1 ~ 12 digits
• Parameters Setting Setting the code
Number of codes:40 - 20~59
for user group1
This section explains the settings of each function, please refer to the
Valid keys:0~9
tables 1 ~ 12 digits
Setting the code for
Number of codes:40 - 60~99
About the setting mode: user group2
Valid keys:0~9
Input the master code to switch to the setting mode, and input the cor-
responding setting code to perform the settings for the function you
want. After settings have been made, input the following setting codes
to continue the setting operation. Press " " to exit the setting mode

-6- DMR21 Technical Manual

 MODULES
Y
AS
2E

Input the master code

Beep+, Beep
(Default: # #)

1.Reset all settings 2.Setting the master code 3.Setting the key 4.Setting the
(Default 1234) illumination time unlock time
(Default 10s) (Default 1s)

Input the setting code. Input the setting code. Input the setting code. Input the setting code.
00+# 01+# 02+# 03+#

Beep+, Beep Beep+, Beep Beep+, Beep Beep+, Beep

Inputting of code Inputting of new master code Inputting of code (ex.: 10) Inputting of code (ex.: 09)
(ex.: 4321)(1~12 digits) range:00 or 10~99 range:01~99
1234+# 4321+# 10+# 09+#

Beep+ Beep+ Beep+ Beep+

- When the “
* cancel” key is pressed, the indicator will show its standby color, the buzzer beeps, and the system
exits the setting mode
- When there isn’t any operation in 10s, the buzzer beeps, and the system exits the setting mode Beep, Beep+

- When setting failure, the buzzer beeps

- All settings will restore to their - The master code is allowed 1~12 - If the key illumination time is set - The unlock time can be set on
default value. digits. The same code cannot be to 00,the key illumination will light both monitor and door station,
and the valid value is the number
- When power on or activate set for both the user code and the up all the time when power on. you set last
the reset all setting item,the master code. It is recommended - If the key illumination time is set to
keypad checking will carry out, that you change the default master 10~99,the key illumination will light
during this time,the key code up for 10~99 seconds.At this mode,
illumination will blink and the the key illumination lights off in
touching operation is forbidden, standby mode, touching any digital
after finish checking,the key key can illuminate,but this is the
illumination will stop blinking invalid digit.
and sent out a long sound of beep

DMR21 Technical Manual -7-

 MODULES
Y
AS
2E

Input the master code

Beep+, Beep
(Default: # #

5.Setting the unlock mode

(Default 0(Opened))
6.Setting operation tone
(Default ON)
7.Reset code setting
*
8. &# function setting
(Default Normal)

Input the setting code. Input the setting code. Input the setting code. Input the setting code.
04+# 05+# 06+# 07+#

Beep+, Beep Beep+, Beep Beep+, Beep Beep+, Beep

0/1 0/1 0/1

Inputting of code (ex.: 1) Inputting of code (ex.: 1) Inputting of code Inputting of code (ex.: 1)
range:0:(open)/1:(close) range:0:(on)/1:(off) range:0:(normal)/1:(reverse)
1+# 1+# 1234+# 1+#

Beep+ Beep+ Beep+ Beep+

- When the “
* cancel” key is pressed, the indicator will show its standby color, the buzzer beeps, and the system
exits the setting mode.
- When there isn’t any operation in 10s, the buzzer beeps, and the system exits the setting mode. Beep, Beep+

- When setting failure, the buzzer beeps.

- The unlock mode can be set on - When the operation tone is - Cancel all the passwords except - When the item is set to 0,press
both monitor and door station, set to 0,pressing the digital the master code. the button to cancel the input,
*
and the valid value is the number keypad will sent out a sound - Restore the master code to and press the # button to confirm
you set last of beep. default value(1,2,3,4) the input.
- When the operation tone is - When the item is set to 1,press
set to 1,pressing the digital the # button to cancel the input,
keypad will blink one time. and press the * button to confirm
the input .

-8- DMR21 Technical Menu

 MODULES
Y
AS
2E

Input the master code

Beep+, Beep
(Default: # #

9. Call tone setting 10.Interference resistant 11.SPK volume adjust 12.Night light level
(Default enable) grade setting setting setting
(Default 2) (Default:4) (Default 4)

Input the setting code. Input the setting code. Input the setting code. Input the setting code.
08+# 09+# 11+# 13+#

Beep+, Beep Beep+, Beep Beep+, Beep Beep+, Beep

0/1
Inputting of code (ex.: 1) Inputting of code (ex.: 3) Inputting of code (ex.: 5) Inputting of code (ex.: 3)
range:0(enable)/1:(disable) range:0~5 range:0~9 range:0~5
1+# 3+# 5+# 3+#

Beep+ Beep+ Beep+ Beep+

- When the “
* cancel” key is pressed, the indicator will show its standby color, the buzzer beeps, and the system
exits the setting mode.
- When there isn’t any operation in 10s, the buzzer beeps, and the system exits the setting mode. Beep, Beep+

- When setting failure, the buzzer beeps.

- If the item is set to 0,the unit will - The larger you set the - Unlock via password is still - Night Light Level:0~5. -
respond a call tone when pressing interference resistant grade, available even when the door The higher the number, the
the “CALL” button. the stronger it will be,but the station is talking state. brighter the lights
- If set to 1, the unit will have no sensitivity of the keypad will - When door station is talking,
respons when pressing the be more lower. you can enter the Master code
“CALL” button - The interference resistant (the LED turns white upon that)
grade setting also will activate to activate the volume adjusting
the keypad checking function:
Speaker adjustment: 3 (up),
6 (down)

DMR21 Technical Manual -9-

 MODULES
Y
AS
2E

Input the master code

Beep+, Beep
(Default: # #

16.Setting the code 17.Setting the code 18.Setting the code 19.Setting the code
forTemporary1 forTemporary2 for user group1 for user group2

20~59 60~99
Input the setting code. Input the setting code. Input the setting code. Input the setting code.
(ex.:21) (ex.:60)
18+# 19+# 21+# 60+#

Beep+, Beep Beep+, Beep Beep+, Beep Beep+, Beep

Inputting of code (ex.: 1006) Inputting of code (ex.: 2011) Inputting of code (ex.: 2011) Inputting of code (ex.: 2012)
1~12 digits 1~12 digits 1~12 digits 1~12 digits
1006+# 2010+# 2011+# 2012+#

Beep+ Beep+ Beep+ Beep

- When the “
* cancel” key is pressed, the indicator will show its standby color, the buzzer beeps, and the system
exits the setting mode.
- When there isn’t any operation in 10s, the buzzer beeps, and the system exits the setting mode. Beep, Beep+

- When setting failure, the buzzer beeps.

- When input the correct temporary password to release the door, - The user code group1 is used to release the first lock,and the user
the system will clear the temporary password after 60 seconds code group2 is used to release the second lock (the second lock
automatically.But you should know that the password is valid within need external device to support).
60 seconds after inputing the correct temporary password - The user code group1 and user code code group2 can contain 40
- The temporary1 is used to release the first lock,and the temporary group passwords
2 is used to release the second lock(the second lock need external - If the password length exceeds 12 digits, the system will sent out
device to support). the sound of “beep,beep,beep,beep”,and the digitals you input
- If the password length exceeds 12 digits, the system will sent out before will be cleared at the same time.
the sound of “beep,beep,beep,beep”,and the digitals you input before - The user code can not be set the same as the master code and
will be cleared at the same time. temporary code.
- The temporary code can not be set the same as the master code
and user code.

-10- DMR21 Technical Manual

 MODULES
Y
AS
2E

• Calling Display
TFT DISPLAY MODULE
This is the user interface of calling process. (Know that if the name
list is created, the resident’s name will be showed on screen)
1. Parts and functions
Press * (Keypad Module) to cancel the call.

Mounting
screw

3.5 inch TFT

screen

Touch sensor
button

• Conversation

This is the user interface of conversation process.

2. Features
The conversation time will be recorded.
• Calling via name list
Press * (Keypad Module) to cancel the call.
• 3.5 inch TFT display
• Operation visualization
• With three touch buttons
• Easy update of name list

3. Functions
• Standby

This is the start point in standby mode, It can be customized.(More

details refer to UI Update section)

• Keypad operation

i) When in standby mode, input the number by pressing keypad, the

room number will be showed on screen.

• Name List Calling

In standby mode, press to show the name list. Press or

to select name. After that, press to call the corresponding user.
ii) When in standby mode, press # key,a password will be asked. This
Press * (Keypad Module) to cancel the call.
is the user interface of password input.

DMR21 Technical Manual -11-

 MODULES
Y
AS
2E

iii) When input admin code,a Setting Code will be asked on TFT CARD READER MODULE
screen.

1. Parts and functions

Mounting
screw

Swiping card
area

LED indicator
• Combination with ID module

When registered ID card will be presented to a Proximity Reader,

“Door open” message will be showed on TFT Display Module screen

2. Features
• Up to 320 user cards can be registered by door station
• Easy management with indicators and sound hints
• Two Master Cards are supplied, one MASTER CARD ADD
and one MASTER CARD DELETE
• The distance of card reading is from 3 to 5 cm
• The Master Cards are necessary when you add or delete user
cards. Please keep them safe for future use
It is possible to create new Master Cards, the old ones are invalid
This is the user interface of adding card, please know that the user automatically
interface of delete card or initialization is similar as the following pic-
ture shows.
3. Card Operation

• Master Card Setting

Power on and short out EB+,EB- , a sound of “BP+” will be sent out,
and the Unlock indicator will turn on

Toggle DIP4 switch for four times, a sound of “BP+,BP” will be sent
out , the Talk indicator and the Unlock indicator will turn on

Show the ADD CARD, a sound of “BP+” will be sent out, the Unlock
indicator is turned on.

Show the DELETE CARD, a sound of “BP+” will be sent out, and all
indicators will be turned off. After 10 seconds, it will exit the Master
Card Setting automatically

-12- DMR21 Technical Manual

 MODULES
Y
AS
2E

• User Card Setting iii) Format Card

Power on and short out EB+,EB- , a sound of “BP+” will be sent out, In standby mode, show the MASTER CARD DELETE, it will sound
and the Unlock indicator will turn on “BP+,BP”, and the Unlock indicator will turn on

i) Add User Card Show the MASTER CARD ADD, it will sound “BP+,BP”, and the Talk
indicator and the Unlock indicator will turn on
In standby mode, show the MASTER CARD ADD, it will sound
“BP+,BP”, the Talk indicator will turn on

Show the MASTER CARD ADD, it will sound “BP”, the Talk indicator
Input the room number you need to set (0 is default). Show User and the Unlock indicator will blink, and after 10 seconds, it will
Cards, it will sound “BP+”, and the Talk indicator blinks ones. You return to standby mode
can continuously show User Cards

iiii) Card Database

i) By PC
ii) By SD Card

Show the MASTER CARD ADD to exit out Add User Card Setting,
it will sound “BP,BP+”, and all indicators are turned off. (without any
operation for 10 seconds, it will return to standby mode)
4. Combination

ii) Delete User Card • Combination With TFT

Module

In standby mode, show the MASTER CARD DELETE, it will sound

“BP+,BP”, and the Unlock indicator is turned on. and the Delete
Card Mode is activated.

1234
56 78
9 0 * #

A B
In Delete Card Mode :

--Delete by room number: Input the room code, it will sound “BP+”,
and the Unlock indicator blinks one time,all associated cards will be
RF CARD

deleted..

--Delete by User Card: Show the User Cards which you need to
delete. It will sound “BP+”, and he Unlock indicator blinks one time.
(You can continuously show user cards that you need to delete)

Show the MASTER CARD DELETE to exit out Delete Card Mode. The informations will be displayed on screen when some operations
It will sound “BP,BP+”, and all indicators are turned off. (without any are carried on, such as Master Card Setting, Add User Card and
operation for 10 seconds, it will return to standby mode) Delete User Card etc.

For example,swipe the user card, the info of “Door Open” will be dis-
played on screen.

DMR21 Technical Manual -13-

 MODULES
Y
AS
2E

• Combination With Keypad Module

CALL BUTTON MODULE

1. Parts and functions

Mounting
screw

Call button

Name plate

Double row call button module

Mounting
screw
1) Master Card Setting(Reserve)
Name plate

2) Add Card Setting(Reserve)

Call button

2) Delete Card Setting(Reserve)

Single row call button module

• Combination With Keypad & TFT Modules

2. Call codes

The DMR21 automatically assigns the call codes to the connected

module’s buttons. Regardless of the structure of the call button mod-
ule, the button numbers are listed from the top to bottom and from
left to right (in the case of double row buttons):

* Examples:

In the case of double row buttons:

ON

• DIP3 switch set Off 1 2 3 4 5 6

09 10
11 12
13 14
15 16
01 02 17 18
03 04 RF CARD 19 20
05 06 21 22
07 08 23 24
01 02 09 10 01 02 25 26
03 04 11 12 03 04 27 28
05 06 13 14 05 06 29 30
07 08 15 16 07 08 31 32

-14- DMR21 Technical Manual

 MODULES
Y
AS
2E

For single row of buttons

ON
• DIP3 switch set Off
1 2 3 4 5 6

10
12
14
16
02 18
RF CARD 04 RF CARD 20
06 22
08 24
02 10 02 26
04 12 04 28
06 14 06 30
08 16 08 32

ON

• DIP3 switch set to on 1 2 3 4 5 6

05
06
07
08
01 09
RF CARD 02 RF CARD 10
03 11
04 12
01 05 01 13
02 06 02 14
03 07 03 15
04 08 04 16

3. Address description

NO. Functions
01 Call apartment 01
02 Call apartment 02
03 Call apartment 03
04 Call apartment 04
05 Call apartment 05
06 Call apartment 06
07 Call apartment 07
08 Call apartment 08

DMR21 Technical Manual -15-

 MODULES CONNECTION
Y
AS
2E

TERMINAL DESCRIPTION • Card reader module

1 2
• Video entry module

INPUT

1 2 3 4 5

OUTPUT

3
6 7 8

NO. Name Descriptions

NO. Name Descriptions 1 JWGN1 Connect to CN/WGN of video entry module
1 SET DIP switches for system configurations 2 JKB' Connect to next call button module
2 JP-LK For electronic lock safety type setting
3 JKB Connect to next call button module
3 CN/KMB Call button module connection port
4 CN/T-COIL Reserved
5 Bus Non-polarity bus line,connect to power comb unit
6 CN-LK Electric lock and exit button connection port
Touch sensor keypad module or TFT display
7 CN/FUN module connection port
• Call button module
8 CN/WGN Card reader module connection port

• Keypad and TFT module

INPUT

OUTPUT

NO. Name Descriptions

2 1 INPUT Connect to CN/KMB of video entry module
2 OUTPUT Connect to next call button module

NO. Name Descriptions

1 CN/FUN_IN Connect to CN/FUN of video entry module
2 CN/FUN_OUT Connect to next keypad or TFT module

-16- DMR21 Technical Manual

 MODULES CONNECTION
Y
AS
2E

CONNECTIONS

• DMR21/D16 • DMR21/T4/D8

CN/KMB
CN/KMB

CN/FUN

INPUT

INPUT

OUTPUT

OUTPUT

INPUT
INPUT

OUTPUT

• DMR21/ID/S4 • DMR21/ID/KP

CN/KMB

CN/WGN CN/FUN CN/WGN

INPUT INPUT

OUTPUT OUTPUT

INPUT

INPUT

1 2 3
4
RF CARD 7 8
5 6
9 * #
0
A B OUTPUT

RF CARD

DMR21 Technical Manual -17-

 MODULE CONNECTION
Y
AS
2E

• DMR21/S8+F3

INPUT

CN/KMB

CN/FUN CN/WGN
OUTPUT

INPUT

INPUT

OUTPUT
OUTPUT

INPUT

INPUT

1 2 3 4
5 6 7 8
9 0 * # OUTPUT
A B OUTPUT

RF CARD

• DMR21/ID/KP

INPUT

CN/KMB

CN/WGN
OUTPUT

INPUT

INPUT

OUTPUT OUTPUT

INPUT
INPUT

RF CARD
OUTPUT

OUTPUT

-18- DMR21 Technical Manual

 CONFIGURATION
Y
AS
2E

COMMON DOOR STATION SETTING 4.Calling

1.Namelist.txt file Setting: • Calling By Buttons

Press the call button to call corresponding monitors

i) Create a TXT file, and named Namelist.

ii) Open the Namelist.txt file, and input 5 [ ] symbols. Each [ ] symbol
has its meaning, see the following picture.

Description:

Button: DMR21 button which you need to set. • Calling By Namelist

Name: It will be displayed on TFT module. i) Press touch sensor button to show the name list

Gateway: Set the Gateway mode recording to BDU address. [08~15]

means BDU address 01~08

Router: Set the Router mode recording to BDU address.[01~08]

means BDU address 01~08

Address: Set the monitor address you want to call.

iii) Edit Namelist.txt file. For example, as the following picture.

ii) Select the name,then press touch sensor button to call

Definition:

[001][Alan_1][08][00][01]

Press the first button, it would call the monitor 01 in BDU 1, and it is • Calling By Keypad Module
displayed Alan_1 on TFT module.
Input the Aprt number on keypad (with keypad module) and press
touch sensor button to call the corresponding monitor

2.Work Mode Setting:

This section is reserved

3.Namelist Update:

For more details please refer to the following section of Namelist

Update By SD Card

DMR21 Technical Manual -19-

 CONFIGURATIONS
Y
AS
2E

SOFTWARE UPDATE TONE UPDATE

1. Format SD card 1. Format SD card

2. Copy the Update DMR21.bin file to SD card by computer. 2. Copy the Update Ring.bin file to SD card by computer.

3.Update software: 3.Update ringtone:

i) Power on the DMR21, and set DIP6 switch to ON, as the following i) Power on the DMR21, and set DIP6 switch to ON, as the following
picture shows: picture shows:

DIP6=ON DIP6=ON
ON ON

1 2 3 4 5 6 1 2 3 4 5 6

CN/KMB CN/KMB

CN/WGN CN/WGN

INPUT INPUT

ii) Insert SD card to slot. ii) Insert SD card to slot.

iii) A long warning sound of “BP+” will be sent out, and the Status
indicator is turned on.
iii) A long warning sound of “BP+” will be sent out, and the Talk indi-
cator is turned on.

iii) After 3 seconds, all the indicators are turned on.

iiii) After 20 seconds, a long sound of “BP+” will be sent out, and the
Talk indicator is turned off, It means Tone update is finished.

iiii) After 20 seconds, a long sound of “BP+” will be sent out, and all
indicators are turned off.It means Software update is finished.

-20- DMR21 Technical Manual

 CONFIGURATIONS
Y
AS
2E

NAMELIST UPDATE

• Update by SD card

1. Format SD card

2. Copy the Update Namelist.bin file to SD card by computer.

3.Update namelist:

i) Power on the DMR21, and set DIP6 switch to ON, as the following
picture shows:

DIP6=ON
ON

1 2 3 4 5 6

CN/KMB

CN/WGN

INPUT

ii) Insert SD card to slot.

iii) A long warning sound of “BP+” will be sent out, and the Talk indi-
cator is turned on.

iiii) After 20 seconds, a long sound of “BP+” will be sent out, and the
Talk indicator is turned off, It means Namelist update is finished.

DMR21 Technical Manual -21-