Three Phase Inverter Circuit Diagram

In this post we are going to construct a three-phase inverter circuit using Arduino and MOSFET. We will
have a brief look at the three phase transformer working and we will construct a three phase transformer
using three “single phase transformer” by combining the windings in delta and start connections. We will
also take a look at the wave form generated by Arduino.

We will see:

Circuit Diagram.
Circuit Description.
Program code for Arduino.
Three phase waveform generated by Arduino.
Push-Pull MOSFET stage.
Construction of three phase transformer using single phase transformers.
Advantage and disadvantage of this three phase inverter circuit.

Also related: 3 Phase sinewave generator

Three Phase Inverter Circuit Diagram:

Three Phase Inverter Circuit

Circuit Description:
 The circuit consists of an Arduino which generates the 3 phase waveform with 120degree electrical
phase difference between each individual waveform. You may use your favorite Arduino board.
The BJTs and MOSFETs are configured in push-pull configuration; three push-pull stages are utilized
for three individual phases.
Three single phase step-down transformers (used in reverse) are connected in delta and star
connection at primary and secondary winding respectively; this will replicate a three phase
transformer.
At the output we have three phases and one neutral line derived by using star connection at
secondary side.
We have used three 0-9V transformer and all must be at-least 5A rated to get a decent power output.
A fuse is included in the circuit to prevent short-circuit due to some unfortunate situations that may
occur.

Program Code For 3 Phase Inverter Circuit:

// --------- <Electronics-project-hub>com -------- //

const int output_1 = 9;
const int output_2 = 10;
const int output_3 = 11;
const int t = 3310;
void setup()
{
pinMode(output_1, OUTPUT); // Phase 1
pinMode(output_2, OUTPUT); // Phase 2
pinMode(output_3, OUTPUT); // Phase 3
}
void loop()
{
delayMicroseconds(t);
digitalWrite(output_1, LOW);
delayMicroseconds(t);
digitalWrite(output_2, HIGH);
delayMicroseconds(t);
digitalWrite(output_3, LOW);
delayMicroseconds(t);
digitalWrite(output_1, HIGH);
delayMicroseconds(t);
digitalWrite(output_2, LOW);
delayMicroseconds(t);
digitalWrite(output_3, HIGH);
}
// --------- <Electronics-project-hub>com -------- //

Waveform generated by Arduino:

All three phases are shifted 120 degree electrically with each individual phase and yes, this is not a pure
sine wave type.

A86L-0027-0001#102 Testado -
Em stock - No mesmo dia

ACESSAR

Ad

3 phase square wave output

The above wave-forms are generated by Arduino at pins 9, 10and 11. The last two waveforms are moved
downwards on the oscilloscope, so that the waveform don’t overlap each other and we can compare the
wave-forms.

To get a clear idea we have marked the waveform so that we can see the 120 degree phase shift in the
wave from.
 3 phase output

As we can see that each waveform are 120 degree electrically shifted from each other. The generated
three phase signal cannot be applied directly to the transformer to step-up; to do this the three phase
signals are applied to a buffer stage which consists of BJTs and MOSFETs.

All the three phase signals are 50Hz and 50% duty cycle with respect to ground.

Push-Pull MOSFET Driver Stage:

The feeble three phase signals are pre-amplified by a couple of low power BJTs per phase signal. The
BJT is configured in push-pull configuration so that it can amplify both LOW and HIGH signals; now three
such push-pull stages are implemented in the circuit.

Mouser
Mouser Brazil
 Maior Estoque Do Mundo
Mouser Brazil

The output signal from BJT is inverted by 180 degree from the applied signal (for all three phases). The
5V signal from Arduino is now amplified to 12V signal which is sufficient for a MOSFETs to turn ON and
OFF(fully). If we directly apply the 5V signal from Arduino to gate of the MOSFET, the MOSFET will still
switch ON and OFF (partially) but there will be huge resistance between source and drain terminal which
will not allow maximum current to flow and cause MOSFETs to overheat.

Also Related: 3 Phase sinewave generator

Now the 12V (from BJTs) signal is applied to MOSFETs which is also configured in push-pull. The output
at the MOSFET is now a strong which can drive the three phase transformer. The output signal from the
MOSFET is 180 degree inverted (again) from the BJT’s output, now we got zero degree phase shift with
respect to Arduino’s output. The weak signal from the Arduino is now on the steroid with exactly same
phase difference etc.

Construction of Three Phase Transformer Using Three Single

Phase Transformer:
 NOVO NOVO

NOVO

AliExp​ress​.com

Now here is the most interesting part of the project, we are going to construct a three phase transformer
using three individual ordinary step-down transformers.

We can take three single phase transformers and connect their primary windings each other and
secondary windings each other in star or delta configuration or one of the windings in star and other
in delta configuration, now we can use it with three phase supply.

Delta-Star Connection

In this case the output is configured in “star” with a neutral point taken from the center of the star
connection, while the other side of transformer is connected in delta configuration as illustrated below:
NOVO NOVO

NOVO

AliExp​ress​.com

Three phase inverter transformer

Some terms related to three phase transformer:

Phase Voltage: The voltage between neutral and any one of the phases in “star” configuration is called
Phase Voltage.

In this case the expected phase voltage is 220V at the output.

NOVO

AliExp​ress​.com

Line Voltage: The voltage between any two phases is called Line Voltage.

R$3.27 R$104.75 R$160.82

R$32.47 R$75.42 R$24.08

Mouser Electronics Brasil
Mouser Brazil

In this case the expected phase voltage between any two phases is 440V at the output.

The delta-star (wye) transformers are commonly used for commercial and industrial purposes.
Combining three single phase transformers are a common practice for manufacturing single three
phase transformer for cost effectiveness and reducing the weight.

R$259.99 R$249.99 R$199.99

R$169.99 R$219.99 R$169.99

Pichau Info
Pichau

Simulation for the proposed three phase inverter circuit:

Three Phase Inverter Circuit Using Arduino -Simulation

Download simulation files here: Click here

 Sharp Microelectronics MACOM
PC817XNNIP1B MAAD-007078-000100
Optoacopladores de… Atenuadores
R$ 3,27 R$ 104,75

STMicroelectronics
NUCLEO-H755ZI-Q
Placas e kits de…
R$ 160,82

Mouser Brazil

Advantage and disadvantage of this three phase inverter

circuit:

Advantages:

Simplest design, even a beginner to intermediate hobbyist can replicate this circuit.

···

No need to purchase expensive three phase transformer, three “single phase step-down
transformers” are enough.
Disadvantage:

The output is square wave which is not suitable for many inductive loads.

···

If you have any questions regarding this post, please comment below you can anticipate a
guaranteed reply from us.

Blogthor
My nick name is blogthor, I am a professional electronics engineer specialized in
Embedded System. I am a experienced programmer and electronics hardware
developer. I am the founder of this website, I am also a hobbyist, DIYer and a constant
learner. I love to solve your technical queries via comment section.

Arduino, Inverter, MOSFET

Arduino, Inverter