Daewoo G25S-2 Hydraulic Service Manual

https://truckmanualshub.
com/
SB2097E00
Aug. 1996
Specifications
Systems Operation
Testing & Adjusting
Disassembly & Assembly
New Hydraulic Systems
D20/25-2
D20/25/30S-2
G20/25/30S-2
G20/25/30S-2
https://truckmanualshub.com/
Important Safety Information

Most accidents involving product operation, maintenance and repair are caused by failure to observe
basic safety rules or precautions. An accident can often be avoided by recognizing potentially
hazardous situations before an accident occurs. A person must be alert to potential hazards. This
person should also have the necessary training, skills and tools to perform these functions properly.
Improper operation, Iubrication, maintenance or repair of this product can be dangerous and
could result in injury or death.
Do not operate or perform any Iubrication, maintenance or repair on this product, until you
have read and understood the operation, Iubrication, maintenance and repair information.
Safety precautions and warnings are provided in this manual and on the product. If these hazard
warnings are not heeded, bodily injury or death could occur to you or other persons.
The hazards are identified by the "Safety Alert Symbol" and followed by a "Signal Word" such as
"WARNING" as shown below.
WARNING
The meaning of this safety alert symbol is as follows :
Attention! Become Alert! Your Safety is Involved.
The Message that appears under the warning, explaining the hazard, can be either written or
pictorially presented.
Operations that may cause product damage are identified by NOTICE labels on the product and in
this publication.
DAEWOO cannot anticipate every possible circumstance that might involve a potential hazard. The
warnings in this publication and on the product are therefore not all inclusive. If a tool, procedure,
work method or operating technique not specifically recommended by DAEWOO is used, you must
satisfy yourself that it is safe for you and others. You should also ensure that the product will not be
damaged or made unsafe by the operation, Iubrication, maintenance or repair procedures you
choose.
The information, specifications, and illustrations in this publication are on the basis of information
available at the time it was written. The specifications, torques, pressures, measurements,
adjustments, illustrations, and other items can change at any time. These changes can affect the
service given to the product.
Obtain the complete and most current information before starting any job. DAEWOO dealers have
the most current information available.
1 of 29
Index
Specifications
Hydraulic Control Valve .......................................... 5
Systems Operation
Hydraulic Control Valve ........................................ 17

Assembly And Construction .......................... 17
Check Valve .................................................. 21
Flow Control Valve And Relief Valve ............ 20
Valve Operation ............................................ 18
Hydraulic System (D20/25/30S-2,
G20/25/30S-2, GC20/25/30S-2 Model) ................. 6
Hydraulic System (D20/25-2 Model Only) ............ 11
Anti-Stall And Remote Relief Valve .............. 14
Testing And Adjusting
Hydraulic System .................................................. 23

Flow Control Valve Adjustment ..................... 24
Relief Valve Pressure Check ........................ 23
Troubleshooting .................................................... 22
Disassembly And Assembly
Assembly .............................................................. 28
Cleaning, Inspection And Repair .......................... 26
General ................................................................. 25
Unit Disassembly .................................................. 25
New Hydraulic Systems 3 of 29 Index

Specifications
Hydraulic Control valve (1) Torque for bolts that hold control valve sections
together ................ 40.5 ± 2 N•m (360 ± 18 lb•in)
(2) Adjust TILT and sideshift relief valve pressure as

CONTROL VALVE shown above. See Relief Valve Pressure Check
Main Relief TILT, Auxiliary in Testing And Adjusting.
Valve Relief Valve
Pressure Pressure (3) Torque for nipple assembly ........ 36.5 ± 0.5 N•m
± 500 kPa ± 350 kPa (320 ± 4 lb•in)
Model Mast (± 75 psi) (± 50 psi)
See Folw Control Valve Adjstment in Testing And
D(G)20(S) Std 18,100 (2625) 15,500 (2250) Adjusting.
GC20(S) FFL
FFTL (4) Torque for screws ............................12 ± 1.5 N•m
D(G)25(S) Std 19,500 (2825) 15,500 (2250) (105 ± 13 lb •in)
GC25(S) FFL
FFTL
D(G)30S Std 21,550 (3125) 15,500 (2250)
GC30S FFL
FFTL
IDCS001B
New Hydraulic Systems 5 of 29 Specifications

Systems Operation
Hydraulic System
(D20/25/30S-2, G20/25/30S-2, GC20/25/30S-2 Model)
1
2
1
2
3
4
6 7
9
10 8
11
12
13
14 15 16 17
IDCS002B
Basic Hydrauic Schematic With Standard Lift

(1) Lift cylinders. (2) Excess flow protectors. (3) Sideshift cylinder(s)(if equipped). (4) Lowering flow control valve. (5) Hydraulic
control valve. (6) Tilt cylinders (7) Relief valve(lift). (8) Relief valve(tilt and sideshift). (9) Hydraulic oil filter. (10) Hydraulic oil
tank. (11) Priority valve. (12) Oil line(trucks with power brakes only). (13) Oil line. (14) Hydraulic strainer. (15) Hydraulic pump.
(16) Oil line to steering gear. (17) Oil line.
New Hydraulic Systems 6 of 29 Systems Operation

The hydraulic system has hydraulic oil tank (10)

which holds the oil for gear type hydraulic pump (15).
Hydraulic pump (15) sends pressure oil to the power
brakes (if equipped), hydraulic and steering systems.
Pump oil flows from pump (15) to priority valve (11)
where the oil folw divides to the power brakes brake
valve (if equipped)(not shown) through line (12) and
to the steering gear through line (16).
The control valve levers move the valve spools in

control valve (5) to let the pump oil in the control
valve go to lift cylinders (1) and/or (19), tilt cylinders
(6) or sideshift cylinder(s) (3).
The return hydraulic oil from the cylinders flows

through hydraulic control valve (4), line (13), into filter
(9) and hydraulic tank (10). Relief valve (7) in the
control valve body will make the flow control valve
release extra pressure to the hydraulic tank when the
pressure in the lift or tilt circuits goes higher than
relief valve pressure shown in the Control Valve
section of Specifications. Relief valve (8) does the
same thing for the sideshift circuit when it goes
higher than the auxiliary relief valve pressure shown
in the Control Valve section of Specifications.

18 19
1
2
1
2 3
4
7
6
10 8
11
12
13
14 15 16 17
IDCS003B
Basic Hydraulic Schematic With Standard Lift

(1) Lift cylinders. (2) Excess flow protectors. (3) Sideshift cylinder(s)(if equipped). (4) Lowering folw control valve. (5) Hydraulic
control valve. (6) Tilt cylinders. (7) Relief valve(lift). (8) Relief valve(tilt and sideshift). (9)Hydraulic oil filter. (10) Hydraulic oil
(16) Oil line to steering gear. (17) Oil line. (18) Excess folw protector. (19) Lift cylinder(primary).
The maximum speed at which the lift cylinder(s) are The tilt forward, tilt back and sideshift speeds are
lowered is controlled by lowering flow control valve (4). controlled by flow control valves in hydraulic control
valve (5). There is an anti-cavitation valve inside the tilt
Excess flow protectors (2) and (18) will act as flow spool to prevent cavitation (development of air pockets)
control valve if an oil line between them and flow in tilt cylinders (6).
control valve (4) is broken when the mast is raised or
lowered. This prevents a sudden fall of the mast or REFERENCE : For the Hydraulic Systems Schematics.
carriage if an oil line is broken.

Hydraulic System (D20/25-2 Model Only)
1
2
1
2
3
4
7
6
9
8
10 11
12
13
20
14 15 16 17 18 19
IDCS004B

control valve. (6) Tilt cylinders. (7) Relief valve(lift). (8) Relief valve(tilt and sideshift). (9) Hydraulic oil filter. (10) Hydraulic oil
(16) Oil line to steering gear. (17) Oil line. (18) Remote relief valve. (19) Oil line(trucks with anti-stall valve only). (20) Anti-stall
valve(if equipped).

The hydraulic system has hydraulic oil tank (10) which

holds the oil for gear type hydraulic pump (15).
Hydraulic pump (15) sends pressure oil the power
brakes (if equipped), hydraulic and steering systems.
Pump oil flows from pump (15) to priority valve (11)
where the oil folw divides to the power brakes brake
valve (if equipped)(not shown) through line (12) and to
the steering gear through line (16). Oil also flows
through anti-stall valve (20), to hydraulic control valve
(5) and back to hydraulic tank (10).
When the lift truck is at idle speed the hydraulic pump

delivers a low oil flow. If the lift, tilt or auxiliaries are
used the pressure in line (17) will increase and
remote relief valve (18) will dump oil to hydraulic tank
(10). As engine speed is increased, oil flow
increases, anti-stall valve (20) now closes the
passage to remote relief valve (18). With remote
relief valve (18) blocked, normal hydraulic relief
pressures are available.
The control valve levers move the valve spools in

control valve (5) to let the pump oil in the control
valve go to lift cylinders (1) and/or (22), tilt cylinders
(6) or sideshift cylinder(s) (3).
The return hydraulic oil from the cylinders flows

through hydraulic control valve (4), line (13), into filter
(9) and hydraulic tank (10). Relief valve (7) in the
control valve body will make the flow control valve
release extra pressure to the hydraulic tank when the
pressure in the lift or tilt circuits goes higher than
relief valve pressure shown in the Control Valve
section of Specifications. Relief valve (8) does the
same thing for the sideshift circuit when it goes
higher than the auxiliary relief valve pressure shown
in the Control Valve section of Specifications.

21 22 1
2
1
2 3
4 7
9
8
10
11
12
13
14 15 16 17 18 19 20
IDCS005B

control valve. (6) Tilt cylinders. (7) Relief valve(lift). (8) Relief valve(tilt and sideshift). (9) Hydraulic oil filter. (10) Hydraulic oil
(16) Oil line to steering gear. (17) Oil line. (18) Remote relief valve. (19) Oil line(trucks with anti-stall valve only). (20) Anti-stall
valve. (21) Excess flow protector. (22) Lift cylinder(primary).
The maximum speed at which the lift cylinder(s) are The tilt forward, tilt back and sideshift speeds are
lowered is controlled by lowering flow control valve (4). controlled by flow control valves in hydraulic control
valve (5). There is an anti-cavitation valve inside the
Excess flow protectors (2) and (21) will act as flow tilt spool to prevent cavitation (development of air
control valve if an oil line between them and flow pockets) in tilt cylinders (6).
control valve (4) is broken when the mast is raised or
lowered. This prevents a sudden fall of the mast or REFERENCE : For the Hydraulic Systems Schematics.
carriage if an oil line is broken.

Anti-Stall And Remote Relief Valve
The anti-stall valve in combination with the remote

relief valve prevent hydraulic overloads at engine
idle, which could cause excessive vibration and
engine stalling. At engine idle, the anti-stall valve
opens ports to the hydraulic control valve and the
remote relief valve. If the hydraulic control valve is
used, the pressure in the oil line from the priority
valve to the anti-stall valve will increase. This
pressure increase will be limited by the remote relief
valve to 8250 kPa (1200 psi) (6R7072 Relief Valve).
This relatively low system pressure allows for a
smoother engine idle because the engine is not
overloaded by the hydraulic pump with an engine
speed of 700 rpm minimum.
As engine speed increases the hydraulic system oil

flow increases. The anti-stall valve senses this flow
increase and closes the output port to the remote
relief valve. Flow is now directed to the main control
valve only and full system pressure can be achieved.

Hydraulic Control Valve
IDCS006B
(1) Relief Valve. (2) Inlet Body. (3) Center Spring. (4) Switch Bracket.
(5) Cam. (6) Center Body. (7) Spool. (8) Tie Stud.
(9) Outlet Body. (10) Check Valve. (11) Seal Rings.
Assembly And Construction Passages between the bodies connect each section
to the common inlet and tank ports.
Seal rings between the sections seal the connecting
Above figure is a cross-section view showing passages, Sections are held together by studs and
construction and assembly of a three-section valve. nuts.
The inlet section also contain a relief valve
assembly.

Valve Operation Lift Spool
IN Pressure to “B”
“A” to tank
By-pass blocked
IDCS007B CENTER “A” and “B” blocked

By-pass open
(1) Control Valve Sensing Orifice.
(2) Flow Control And Relief Valve. OUT “B” to tank
(3) Tank Passage.
(4) By-pass Flow Control Orifice.
“A” blocked
IDCS008B
(5) Cylinder Ports. By-pass open
(6) Pressure Passage. (7) By-pass Passage.
Lift spool - used for control of single acting cylinder

applications. It directs flow to only one end of a
Figure IDCS007B is a schematic illustration of a
cylinder, as in the lift mechanism of a lift truck.
three section valve, showing the inlet and outlet ports
Return flow is from the same end of the cylinder and
and the by-pass, pressure and tank passages.
relies on gravity or mechanical means to retract.
The pressure passage is used to carry fluid to the
cylinder ports when the spools are shifted. The by-
pass passage permits flow directly to the outlet when
the spools are not being operated. The tank passage
also carries fluid to the outlet; either return flow from
the cylinder ports or fluid diverted past the flow
control and relief valve,
The spools are shown in the centered or neutral

position, Under these conditions, fluid in the pressure
passage is blocked from the cylinder ports by the
spool lands. Flow through the valve is through the
by-pass and tank passages to the outlet.
IDCS009B

Tilt Spool Auxiliary Spool
IN “A” to tank
IN Pressure to “B”
“B” blocked
By-pass open
“A” to tank
By-pass blocked
CENTER “A” and “B” blocked
By-pass open
CENTER “A” and “B” blocked
By-pass open
OUT Pressure to “A”
OUT Pressure to “A”
“B” blocked
IDCS012B By-pass blocked
“B” to tank
By-pass blocked
IDCS010B
Auxiliary spool - directs flow to either end of a double

acting cylinder. Flow from the end that is not under
Tilt spool - a counterbalance spool normally used to
pressure is returned to tank via internal coring of the
control the tilt function of a lift truck.
valve section.
The counterbalance feature prevents the forks from
tilting forward faster than the pump can supply oil,
preventing tilt.
IDCS013B
IDCS011B

Flow Control And Relief Valve Flow Control
Earlier design valves were equipped with simple relief

valves in the inlet sections.
The partial flow by-pass system in the LT valve
makes use of a compound type flow control and relief
valve arrangement.
Sensing the pressure drop across an orifice at the

entrance to the by-pass, the valve acting as a control
to limit flow through the by-pass to approximately
seven gallons per minute. The balance of the pump
delivery is diverted through the reservoir passage.
This arrangement greatly reduces pressure drop
through the valve in the neutral position.
IDCS007B
When a spool is shifted to operate a portion of a
machine, the flow control is inoperative and full pump (1) Control Valve Sensing Orifice.
volume is available to the system. The control valve (2) Flow Control And Relief Valve.
then functions as an overload relief valve. System (3) Tank Passage.
pressure is limited to a prescribed maximum by the
(5) Cylinder Ports. (6) Pressure Passage.
action of this valve. Inlet body type F is not equipped (7) By-pass Passage.
with a relief valve. Full pump volume is available to
the system at all times.
Figure IDCS007B shows the valve operation in
Use of the optional secondary relief valve allows the neutral with flow in excess of seven USgpm. Flow
use of lower pressure for tilt and accessory function across the by-pass orifice result in a pressure drop.
while higher pressure is provided for the lift function. Decreased pressure is sensed at the spring end of
the valve sub-assembly through a sensing orifice.
NOTE : The secondary relief valve must be set at a The slightly higher pressure at the other end of the
lower relief setting than the system relief. valve permits it to shift down, diverting excess flow to
the reservoir passage. With flow at less than seven
USgpm there would be negligible pressure drop
across the by-pass orifice. Then the control valve
would be held closed by the large spring and all flow
would be through the by-pass passage.
Optional flow control valves are available for all

operating sections. These valves can be set from
1 - 15 US gpm.

Relief Valve If a different relief valve setting is required, the valve

sub-assembly should be replaced,
Part Setting
Model Number Pressure
D20-2, D20S-2, D144363 2625 psi

G20S-2, GC20S-2 (18,100 kPa)
D25-2, D25S-2 D144364 2825 psi

G25S-2, GC25S-2 (19,478kPa
D30S-2, G30S-2 D144365 3125 psi

GC30S-2 (21,546 kPa)
IDCS014B
(1) Spring. (2) Spool. (3) Poppet. Check Valve

(5) Flow Control And Relief Valve.
(6) Spring. (7) Sensing Orifice.
Operation of the relief valve feature is shown in

above figure. When an operating spool is shifted,
fluid is ported into the system and the by-pass is
blocked.
Above figure A shows operation at less than the relief

valve setting. There is no flow over the by-pass
orifice, so full system pressure is sensed at the spring
end of the control valve, as well as the opposite end.
The valve is thus hydraulically balanced and the large
spring holds the relief spool closed. IDCS014B
Maximum pressure is determined by the setting of (1) Spring. (2) Spool. (3) Poppet.
the small spring inside the control valve assembly. (4) By-pass Flow Control Orifice.
When system pressure is sufficient to overcome this (5) Flow Control And Relief Valve.
(6) Spring. (7) Sensing Orifice.
heavy spring, the poppet is forced off its seat (see
above figure B).
Fluid immediately flows past the poppet to the tank
passage. This flow creates a pressure drop across
Timing of the spools is such that one cylinder port
the sensing orifice and the control valve is no longer
opens to pressure and the other port opens to
hydraulically balanced.
reservoir before the by- pass passage is
completelyblocked.
When pressure drop across the sensing orifice is
great enough to overcome the force of the large
To prevent return flow from passing into the pressure
spring, the valve spool shifts, permitting flow to the
passage and escaping through the partially closed
tank passage.
by-pass, check valves are provided in each operating
section except sections with “ B” spool.
Relief valve sub-assemblies in the inlet section are
The check valves prevent the load from dropping.
pre-set and tested by Vickers for given pressure
settings. Selection of the relief valves setting is based
on the work requirements of the system.

Trouble :
Testing And Adjusting No motion, slow or jerky action of hydraulic system
Remedy
Troubleshooting Probable Cause
Relief valve not properly set, or Repair, clean and readjust

stuck in base and/or worn
Below table lists the difficulties which may be
Dirt or foreign particles lodged Disassemble, clean and
experienced with the unit and the hydraulic system. It
between relief valve control poppet reassemble
indicates the cause and remedy for each of the and seat
trouble listed. It should always be remembered that
pressure and delivery are factors which are usually Valve body cracked inside Replace valve section
dependent upon each other. Adequate pressure
Spool not moved to full stroke Check travel
gauge equippment and a thorough understanding of
the operation of the complete hydraulic system are
essential to diagnose improper conditions. Trouble :
No relief valve action (high pressure)
Trouble :
Probable Cause Remedy
Oil leaks at either end of spools.
Small particle of dirt plugging Remove relief valve and
orifice in relief valve sub- check hole. If blocked, clear
Probable Cause Remedy assembly hole
Defective O-rings in valve Replace O-rings Relief valve sub-assembly

body installed backward Install properly
Trouble :
Load will not hold
Trouble :
Spring-centered spools do not return to neutral. Probable Cause Remedy
Probable Cause Remedy Oil by passing between spool Replace valve

and body
Broken springs Replace springs
Oil by passing piston in cylinder Repair or replace cylinder
Bent spool Replace with new section of
same size and type Cylinder not centered Refer to above spool remedies
Foreign particles Clean system and valve
Misalignment of operating Check linkage for binding Trouble :

linkage condition Load drops when spool is moved from neutral to a
power position
Valve bank improperly Retorque nuts to specified
torqued ratings
Dirt or foreign particles lodged Disassemble, clean and

between check valve ball and seat reassemble
Trouble :
Detent type spools will not stay in detent position Scoreed or sticking check valve Replace poppet
Worn detent barrel Replace detent barrel
Weak or broken detent Replace detent spring

spring
New Hydraulic Systems 22 of 29 Testing and Adjusting

Hydraulic System
2
Relief Valve Pressure Check
1
Tools Needed
Fittings Group
IDCS001C
CONTROL VALVE Pressure Tap Location

(1) Cap. (2) Nipple assembly.
Main Relief Tilt, Auxiliary
Valve Relief Valve
Pressure Pressure
°æ 500 kPa °æ 350 kPa With the engine off, remove cap (1) from nipple
Model Mast (°æ 75 psi) (°æ 50 psi) assembly (2) and connect the 28,000 kPa (4000 psi)
gauge to the nipple assembly.
D(G)20(S) Std 18,100 (2625) 15,500 (2250)
GC20(S) FFL
FFTL
Lift Relief Valve Check and Adjustment
D(G)25(S) Std 19,500 (2825) 15,500 (2250)
GC25(S) FFL
FFTL 1. Start the engine and activate the hydraulics until
the hydraulic oil is at the normal operating
D(G)30S Std 21,550 (3125) 15,500 (2250) temperature. Tilt the mast back to the end of its
GC30S FFL
travel.
FFTL
2. With the engine at high idle, hold the tilt control
lever in the tilt back position and watch the gauge.
Use the Fittings Group to check the relief valve The gauge indication is the pressure that opens
pressure. the relief valve.
3. The correct pressure setting is shown in the chart.
WARNING
Hydraulic oil, under pressure can remain in the
hydraulic system after the engine and pump have
been stopped. Personal injury can be caused if this
pressure is not released before any work is done on
the hydraulic system. To prevent possible injury, 3
lower the carriage to the ground, turn the engine off
and move the control levers to make sure all
hydraulic pressure is released before any fitting,
plug, hose or component is loosened, tightened,
removed or adjusted. Always move the lift truck to a
clean and level location away from the travel of IDCS002C
other machines. Be sure that other personnel are
not near the machine when the engine is running Relief Valve Adjustment.
(3) Plug.
and tests or adjustments are made.

Tilt and Sideshift Relief Valve Flow Control Valve Adjustment

Check and Adjustment WARNING
(1) Flow control valve adjuster.
Hydraulic oil, under pressure can remain in the
1. Start the engine and activate the hydraulics until
hydraulic system after the engine and pump have
the hydraulic oil is at the normal operating
been stopped. Personal injury can be caused if this
temperature. Put the carriage in the full sideshift
pressure is not released before any work is done on
position. the hydraulic system. To prevent possible injury,
2. With the enigne at high idle, hold the sideshift lower the carriage to the ground, turn the engine off
and move the control levers to make sure all
control lever in the full sideshift position and watch
hydraulic pressure is released before any fitting,
the gauge. The gauge indication is the pressure
plug, hose or component is loosened, tightened,
that opens the relief valve.
removed or adjusted. Always move the lift truck to a
3. The correct pressure setting is shown in the chart. clean and level location away from the travel of
other machines. Be sure that other personnel are
4. If an adjustment to the relief valve setting is not near the machine when the engine is running
necessary, loosen nut (5). and tests or adjustments are made.
Lift Section
Remove nut
tie-bolt
6 stud here
5
IDCS003C 1
IDCS016B
Relief Valve Adjustment
(5) Nut. (6) Setscrew.
1. Remove the nut from the main hydraulic valve tie-
5. Turn setscrew (6) clockwise to increase or bolt stud.
counterclockwise to decrease the pressure setting
2. Remove the stud from the valve.
of the relief valve.
3. Use Hex Wrench (6mm), turn the flow control
6. Tighten the locknut and check the pressure setting
adjuster clockwise to increase the flow or
again for correct adjustment.
counterclockwise to decrease the flow.
4. Assemble the tie bolt stud in the valve. Torque the

Flow Control Valve Adjustment stud to 38.5 - 42.5 N ¥m (342 - 378 lb ¥in)
5. Reinstall the nut on the tie bolt and torue

The tilt and first attachment speeds can be adjusted 38.5 - 42.5 N ¥m (342 - 378 lb¥in).
at the control valves. They can be adjusted by turning
plug the in the hydraulic control valve body. The lift
speed can not be adjusted. Do the procedure that
follows to change the flow control assembly.

Disassembly And Assembly
General Attaching Parts
During disassembly, particular attention should be given 1. Remove the four nuts (1) and four tie studs (2).
to identification of parts for reassembly. Spools are
selectively fitted to valve bodies and must be returned to 2. Separate the valve sections, being careful not to
the same bodies from which they were removed, destroy or lose spacers.
Valve sections must be reassembled in the same 3. Remove retainer (3), seals (4) and O-rings(5).
order. Figure IDCS015B is an exploded view showing
the proper relationship for reassembly. Reference is
made to these figures in the procedures which follow. Flow Control Checks
1. Remove flow control check springs (6) and ball(s)

WARNING (7).
Before breaking a circuit connection, make certain

that power is off and system pressure has been End Caps
released. Lower all vertical cylinders, discharge
accumulators, and block any load whose
movement could generate pressure. Plug all 1. Unscrew two screws (8) holding dust cover (9),
removed units and cap all lines to prevent the entry retainer (10) and sleeve (11).
of dirt into the system
2. Remove the O-ring (12) from the sleeve.
Unit Removal Operating Spool
1. Thoroughly clean the exterior of the valve and the 1. Slide the spool (13) out of its bore.
area around the valve to prevent contamination of
the system during removal. 2. Remove the quad seals (14) from the valve body
around the spool bore.
2. Loosen mounting bolts that hold valve to mounting
surface. Be ready to catch fluid retained inside 3. Remove the wiper seal (15).
lines and valve.
NOTE : Do not remove the centering spring (16) or
3. Remove valve from mounting surface and set it on the retainers (17) unless it is necessary to replace
a clean work bench. them.
Unit Disassembly Check Valve
NOTE : All parts within the unit must be kept clean 1. Remove the retainer ring (18) and screw out plug
during the overhaul process. Handle each part with stop adjuster (19) from the valve body.
great care. The close tolerance of the parts makes
this requirement very important. Clean all parts that 2. Remove the back-up ring (20) and O-ring (21).
are removed from the unit with a commercial cleaning
solvent that is compatible with the system fluid. 3. Remove the spring (22) and ball (23) from the
Compressd air may be used in the cleaning process, valve body.
however, it must be filtered to remove water and
other contamination. Be sure the unit is not subjected
to pressure. Disconnect and cap all lines and
disconnect linkage to the spool.
New Hydraulic Systems 25 of 29 Disassembly and Assembly

Adjustable Flow Control Valve Cleaning, Inspection And

Repair
1. Remove the retainer ring (18) and screw out plug
stop adjuster (19) from the valve body.
1. Check that all internal passages are clean and free
from obstruction. Examine all mating surfaces for
2. Unscrew the adjustable relief seat (24) from the
nicks and burrs. Minor nicks and burrs can be
plug stop adjuster (19).
removed with a crocus cloth or an India stone.
3. Remove the back-up ring (20) and O-ring (21).
2. Discard all old seals and O-rings. Wash all parts in
a clean mineral oil solvent and place them on a
4. Remove the spring (22) and poppet (25) from the
clean surface for inspection.
valve body.
NOTE : Obtain new seal kits. Refer to the appropriate
part drawing as shown on figure IDCS015B for the
Relief Valve Subassembly seal kit part number. Apply a light film of clean
hydraulic fluid to the new seals. This will make
assembly easier and also provide initial lubrication of
1. Screw out the plug (26) which retains the relief
moving parts.
valve and remove the O-ring (27) from the plug.
3. Inspect the valve spools and bores for burrs and
2. Remove the spring (28) and the relief valve sub-
scoring. If scoring is not deep enough to cause
assembly (29).
objectionable leakage, the surfaces can be stoned
or polished with crocus cloth. If scoring is
excessive, the valve body and spool must be
Secondary Adjustable Relief Valve replaced. Check the valve spool for freedom of
movement in the bore.
1. Screw out relief plug (30) and remove O-ring (31)
CAUTION : DO NOT stone the edges of spool
from valve body.
sealing lands. Remove minor burrs with #500 grit
paper. Use paper very lightly on the outer diameter of
2. Remove setscrew (32) and nut (33) from relief
each spool.
plug.
4. Check the relief valve for smooth movement in its
3. Remove O-ring (34) and spring (35) from relief
bore. The valve should move from its own weight.
plug.
5. Inspect all screws for evidence of damaged
4. Pull piston (36) and poppet (37) from the plug.
threads. If threads are damaged, replace the
screws.
Valve Body 6. Inspect all springs for distortion or wear. The ends
of the springs shall be square and parallel to each
other. Replace springs that are damaged or
1. Remove the plug (38) and O-ring (39) from
distorted.
cylinder °∞b°± work port.
2. Remove the plug (40) and O-ring (41) on models

with a single acting spool. If the alternate discharge
port is plugged, it is not necessary to remove the
plug unless the body is to be replaced. On bodies
equipped with the quick disconnect option, remove
the dust cap (42) and the coupling (43).
3. Remove O-ring (44) from coupling.
4. Unscrew the plug (45) and remove O-ring (46).

IDCS015B

Assembly Relief Valve
1. Install a new O-ring (27) on the relief valve plug

Assembly is generally performed in reverse order of (26).
disassembly. Refer to figure IDCS015B during the
following assembly procedure. 2. Place the relief valve assembly (29) in its bore,
HEX NUT END UP.
NOTE : Coat all parts with clean hydraulic oil to
facilitate assembly and provide initial lubrication. 3. Install the spring (28) and plug. Tighten the plug
Petroleum jelly can be used to hold seal rings in securely, but do not Over Tighten.
place on assembly.
Optional Adjustable Flow Control Valve

Valve Body
1. Install a new back-up ring (20) and O-ring (21) on
1. Install new O-ring (39) on plug (38) and install in the plug stop adjuster (19) with the O-ring toward
cylinder “b ” work port. On models with a single the spring (22) and seat (24).
acting spool, install new O-ring (41) on the port
plug (40) and plug the appropriate cylinder port. 2. Place the poppet (25) and spring in the body and
install the plug stop adjuster. Be sure the hole in
2. Tighten the plug (40) securely but DO NOT over the plug lines up with the stud hole in the body.
tighten.
3. Replace retaining ring (18).
3. On bodies with the quick disconnect option, install
new O-ring (46) on plug (45) and screw into bore.
Check Valve
4. Tighten the plug (45) to a torque of 97 - 106 N ¥m
(71 - 78 lb ¥ft).
1. Install a new back-up ring (20) and O-ring (21) on
5. Install new O-ring (44) on quick disconnect the plug stop adjuster (19) with the O-ring toward
coupling (43) and insert coupling into plug. the spring (22) and ball (23).
6. Tighten the coupling (43) to a torque of 2. Place the ball and spring in the body and install the
29 - 31 N¥m (21 - 23 lb ¥ft). plug stop adjuster (19). Be sure the hole in the
plug lines up with the stud hole in the body.
7. Install dust cap (42).
3. Replace retaining ring (18).
Secondaty Adjustable Relief Valve

Operating Spool
1. Replace O-ring (34), piston (36) and spring (35) in

relief plug (30). 1. If the centering spring was removed, install spring
(16) and retainers (17) on the spool (13).
2. Insert poppet (37) in plug.
2. Slide the spool into the bore.
3. Install the O-ring (31) on the relief plug. Tighten the
plug securely in valve body. DO NOT over tighten.
CAUTION : Hex head of relief valve must be face

outside of unit.

End Cap
1. Install new O-ring (12) on the sleeve(11).
2. Insert sleeve (11) into retainer (10).
3. Assemble dust cover (9) and retainer and sleeve

with attaching screws (8).
4. Tighten the screws (8) to a torque of 11 - 15 N¥m

(8 - 11 lb¥ft).
Flow Control Checks
1. Insert small check spring (6) into larger spring.
2. Install flow control sensor ball(s)(7) and springs in

proper bores of inlet and mid-body sections.
Attaching Parts
CAUTION : Make sure all mating surfaces of valve

bodies are clean and free of burrs.
1. Install seals (4), O-ring (5) and the retainer (3) in

the grooves in the body of each inlet and mid-body
section.
2. Carefully place the sections together in the same

order in which they were removed.
3. Coat the stud threads with Loctite or a similar

sealant and install the studs.
4. Tighten the nuts to 38 - 44 N¥m (28 - 32 lb ¥ft)

torque.

Daewoo G25S-2 Hydraulic Service Manual

Uploaded by

Copyright:

Available Formats

Daewoo G25S-2 Hydraulic Service Manual

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Daewoo G25S-2 Hydraulic Service Manual

Uploaded by

Copyright:

Available Formats

https://truckmanualshub.

Important Safety Information

The meaning of this safety alert symbol is as follows :

Attention! Become Alert! Your Safety is Involved.

Hydraulic Control Valve .......................................... 5

Hydraulic Control Valve ........................................ 17

Testing And Adjusting

Hydraulic System .................................................. 23

Disassembly And Assembly

New Hydraulic Systems 3 of 29 Index

(2) Adjust TILT and sideshift relief valve pressure as

New Hydraulic Systems 5 of 29 Specifications

Basic Hydrauic Schematic With Standard Lift

New Hydraulic Systems 6 of 29 Systems Operation

The hydraulic system has hydraulic oil tank (10)

The control valve levers move the valve spools in

The return hydraulic oil from the cylinders flows

New Hydraulic Systems 7 of 29 Systems Operation

Basic Hydraulic Schematic With Standard Lift

New Hydraulic Systems 8 of 29 Systems Operation

Hydraulic System (D20/25-2 Model Only)

Basic Hydraulic Schematic With Standard Lift

New Hydraulic Systems 11 of 29 Systems Operation

The hydraulic system has hydraulic oil tank (10) which

When the lift truck is at idle speed the hydraulic pump

The control valve levers move the valve spools in

The return hydraulic oil from the cylinders flows

New Hydraulic Systems 12 of 29 Systems Operation

Basic Hydraulic Schematic With Standard Lift

New Hydraulic Systems 13 of 29 Systems Operation

Anti-Stall And Remote Relief Valve

The anti-stall valve in combination with the remote

As engine speed increases the hydraulic system oil

New Hydraulic Systems 14 of 29 Systems Operation

Hydraulic Control Valve

New Hydraulic Systems 17 of 29 Systems Operation

Valve Operation Lift Spool

IDCS007B CENTER “A” and “B” blocked

Lift spool - used for control of single acting cylinder

The spools are shown in the centered or neutral

New Hydraulic Systems 18 of 29 Systems Operation

Tilt Spool Auxiliary Spool

Auxiliary spool - directs flow to either end of a double

New Hydraulic Systems 19 of 29 Systems Operation

Flow Control And Relief Valve Flow Control

Earlier design valves were equipped with simple relief

Sensing the pressure drop across an orifice at the

Optional flow control valves are available for all

New Hydraulic Systems 20 of 29 Systems Operation

Relief Valve If a different relief valve setting is required, the valve

D20-2, D20S-2, D144363 2625 psi

D25-2, D25S-2 D144364 2825 psi

D30S-2, G30S-2 D144365 3125 psi

(1) Spring. (2) Spool. (3) Poppet. Check Valve

Operation of the relief valve feature is shown in

Above figure A shows operation at less than the relief

New Hydraulic Systems 21 of 29 Systems Operation

Relief valve not properly set, or Repair, clean and readjust

Defective O-rings in valve Replace O-rings Relief valve sub-assembly

Probable Cause Remedy Oil by passing between spool Replace valve